Nutek ATRA Transmitter User Manual

2) During the run cycle, enter the vehicle using your door key or, if the unlock option is installed,

once you are within range of the vehicle, press and hold the transmitter button for 3 seconds to

unlock the vehicle doors.

3) Enter the vehicle, insert your key and turn it to the run, NOT START, position, then step on the

brake, the vehicle is now in control of the ignition key.

NOTE: For push to start vehicles, contact your installation center for proper procedure.

4) With vehicle running, if you wish to make a quick stop and leave the vehicle running, once

you arrive at your destination:

a) place the gear selector in Park,

b) set the parking brake,

feature is useful in extremely cold climates where starting the engine is the only means to keep

the battery charged and uids warm. The operator has the option to have the unit start every 2 or

4 hours for a maximum of 48 hours. Factory preset is to start at 4 hour intervals. To select 2 or

4 hour automatic start timer:

1. Start By Holding the Push Button Switch found on the windshield mount receiver on.

the siren and or lights ash and chirp 4 times indicating that the 4 Hour Start Interval has suc-

cessfully been set.

NOTE: Once selected, 2 or 4, this timer interval will remain in memory until it is manually

changed. To change, the above sequence will have to be followed.

TIMED START OPERATION:

To begin the start timer, within 10 seconds of turning off the ignition switch, activate the RF com-

mand to start 2 times. (Press the start button four times). The lights will ash and the siren will

chirp 4 times. Indicating timed interval mode has been initiated. The vehicle will automatically start

every 2 or 4 hours as programmed. To cancel the timed start mode start the vehicle either by RF

or by the ignition key.

switch located on the receiver unit on.

2) Turn the ignition switch on, off, on, off, on, off.

3) The LED begins to ash two short ashes followed by one long ashes and continues this

The action above puts the unit into the Remote Start Override mode or vehicle service mode and

will not start from the RF transmitter or any other input.

To Exit Remote Start Override Mode:

1) With the system disarmed, Press and Hold the PBLED on.

2) Turn the ignition switch on, off, on, off, on, off.

3) Press and hold the transmitter start button, until the LED on the receiver turns solid.

4) Release the transmitter button. Programming is complete.

5) Repeat step 3 for all new or additional transmitters you want to operate your system up to a

total of four.

The above action programs the rst 3 channels of the transmitter, or the start channel of the one

button transmitter, regardless of the number of buttons.

If you have lost a transmitter and want to insure it is no longer capable of operating your vehicle,

it is suggested that you erase all transmitters before recoding or adding any new ones.

For this action you will need all transmitters you want to control the system present before

4) Turn the ignition switch off.

Once you have erased all transmitters, you will have to go back and program all transmitters

that you want to operate your system.

Transmitter Battery Replacement

1) Locate the slot at the lower right hand side of the transmitter case.

the case halves.

3) Carefully slide the CR2032 battery out from under the battery clip and dispose of properly.

FCC COMPLIANCE

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

—Consult the dealer or an experienced radio/TV technician for help.

Warning!

responsible for compliance could void the use’s authority to operate the equipment

NOTE: The manufacturer is not responsible for any radio or TV interference caused by

to operate the equipment.

NOTE: The 1BER17XPRP two way transmitter used two CR2025 Batteries.

1) Locate and remove the “00” point Phillips head screw located in the lower center on the back