Nutek ATRNA Transceiver User Manual

Nutek Corporation Transceiver Users Manual

Users Manual

128-93091 of 24Page 1Model APS-997EOwners Guide2 Way LCD Long Range Vehicle Security & Remote Start System PATENTED: www.voxxintl.com/company/patents Table Of Contents:Features and Options Page 2 - 4Arming Your System Page 4Protection While The System Is Armed Page 5Disarming The System Page 5 - 6Intrusion Signals and Tones Page 7Valet Override, Programming & Safety Control Switch Page 7Programming Custom Code Override Page 8 - 9Eliminating the Normal Arm & Disarm Chirps Page 9Remote Panic Operation Page 10Remote Control Shock Sensor Selection Page 10 - 11Push Button LED Receiver Safety Control Switch Page 11Remote Starting Your Vehicle Page 11 - 12Automatic Start Timer Operation Page 12 - 13Optional Device Channels Page 13 - 15Turbo Timer Mode Page 15Telematic Upgrade Page 15Two Way Remote (Transceiver) Screen Icons & Indications Page 15 - 2124 Hour Timed Start Setup, Operation, and Use Page 21Temperature Start Mode Operation Page 21Two Way Remote Function Program Chart Page 22Functions At A Glance Page 23Replacement or Additional Transmitters Programming Page 24
128-9309 of 2 of 24Page 25 Button Remote Start Security System With Plug-In Shock Sensor & Starter DisableIMPORTANT! In order to provide you with the highest level of security to your vehi-cle, this system is equipped with selectable manual override circuitry. It is possible that you will need to override you security system if the transmitter becomes lost, or inoperative due to battery failure. Reading the sections on "Manually Overriding Your System" is necessary to fully understand the procedure required to enable your vehicle in such situations. In addition, the chart on page 23 of this manual has a section for the particular features and options installed in your vehicle as well as the override method selected. Although the default mode is "Valet Switch" operation, the system can be congured for "Custom Code" operation for enhanced security. Conrm the override mode selected on page 23 of this manual, and familiarize yourself with the section on it's operation. FEATURES:  1 Two Way 5 Button Remote Control And 1 One Way 5 Button Remote Control Six Channel Code Learning Programmable Receiver  External Superheterodyne Transceiver Antenna w/Push Button Switch & LED  Single Or Two User Programmable W/Separate Control Outputs Single Button Lock/Unlock or Separate Button Lock/Unlock or Both  Remote Keyless Entry With Optional Access Guard (must have power door locks) Selectable Manual Override Mode  New Enhanced Panic Feature (Any button other than unlock stops siren, no change to the units state) Smart Disarm (If triggered, elect to shut off siren, or disarm entire unit ) Adjustable Shock Sensor Via The Transmitter (Pre-Detect Off, Pre & Full Detect Off, City Mode) Safe Start Output Controlled From Channel 3 (Option Channel 3 For Trunk, Or For Remote Start) 24 Hour Time Start Mode Cold Temperature Start Mode 2 or 4 Hour Automatic Start Mode Parking Meter Count Down Timer On LCD Remote Additional Count Down Timer Mode Remote Panic In All Modes (Press & Hold Lock/Unlock Button For 3 Seconds To Engage) Improved Custom Code Override, User Selectable and Programmable Protected Push Button Valet/Override Switch In Windshield Receiver  7-Function LED-Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming Intrusion Alert With Memory Instant Siren Activation Starter Disable Output  Additional Engine Immobilizer Output, (Optional Relay Required)
128-93093 of 24Page 3 True Last Door Arming (Hardwire Only) Defective Zone By-Pass Defective Zone Chirp Conrmation (Unit Chirps To Report Zone Cleared) 6 Tone Mini Siren  Car Horn Output For Additional Alarm Response (Improved Timing To Minimize RF Interference.) Additional Negative Trigger Input (Hood and Trunk) RF Inhibit With Ignition On Parking Light Flasher (Relay On Board) Plug In Dual Stage Shock Sensor (Pre-detect, Full Trigger and “City Mode”)  Audible Arm, Disarm, Defect, and Tamper Chirp Indications Headlight Control Output Illuminated Entry Control Output  Active or Passive Arming Selectable Programmable Auto Lock On / Off Programmable Auto Unlock On / Off/Drivers Door/All Doors Programmable Door Lock Pulse Duration 1 Second / 3.5 Seconds/1 Sec L/ Dbl. U/L Programmable Active or Passive Door Locks User Programmable Permanent Chirp Delete On Command RF Chirp Delete from Transmitter Or Selectable Through Software  Dome Delay Learn Circuitry  Two Vehicle OperationOPTIONS : Remote Trunk Release (must have electric trunk release) Remote Keyless Entry (must have power door locks) Multiple Vehicle Capable Remote Power Window Roll UpWARNING! Be certain that the vehicle is outdoors before using this or any remote vehicle starting device. A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs. DO NOT remote start the vehicle if it is garaged.YOUR “SPREAD SPRECTUM" TRANSMITTERSThe transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on any current automotive security system. Some of today’s sophisticated auto thieves use a device known as a code grabber, which will receive and store the signal from your key chain transmitter and re-transmit at a later time to disarm your system.Your Spread Spectrum transmitters will shift frequencies making it impossible for a thief to grab and rebroadcast your code.
128-9309 of 4 of 24Page 4PRESTIGE1 2If your transmitter button is pressed more than fty times while it is out of range of the vehicle (children playing with your keys), the transmitter will not operate when you return to the vehicle, and will need to be re-aligned to the receiver. To do this, simply press button 1, (lock), two times within a one second time period. The system will now respond to that transmitter each time a button is pressed.NOTE: This system is custom congurable and can be set up to operate with a number of options controlled from any transmitter button or button combination. For reference, we will describe operation assuming that your system is programmed for separate lock and unlock buttons. Also reference will be made to the icons as shown on the buttons left.NOTE: The LCD based remote will be explained in detail further in this manual See "System Status" described later in this manual. Consult your installation center if your system has been congured differently.NOTE: Your system has the option of using a siren, the vehicle horn, or both for the sounding device. Where the siren is referenced below, the horn or both may in fact chirp, or beep. ARMING THE SYSTEM - ACTIVE1. Turn off the engine, exit the vehicle, and close all doors, hood lid and trunk lid.2. Press and release Lock/Arm button on the keychain transmitter. The dash mounted LED begins to ash slowly. Parking Lights ash one time. Siren sounds one chirp.If the siren/horn sounds 3 chirps, then you have left a door, trunk, or hood lid ajar. Simply close the opened entry point to provide full protection. If the siren "chirped" three times, sometime after arming, the exclusive delayed dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired. Again, closing the hood, trunk, or doors will correct the problem and you do not need to disarm the system to make the correction. If the siren/horn did not sound when arming, then the chirps have been turned off and you should refer to the section titled "ELIMINATING THE ARM/DISARM CHIRPS" in this manual. Doors Lock - OptionalNOTE: If the optional Headlamp illumination feature has been added, and has been selected for operation when arming, as an added convenience, the system will turn on the headlights when the system is armed. SILENT ARMING - ACTIVE (Feature must be active during programming)During step 2 above, hold the transmitter button for 2 seconds then release. The unit will arm without the chirps for this one lock cycle.
128-93095 of 24Page 5 ARMING THE SYSTEM - PASSIVE (AUTOMATIC) (Must be activated during programming)1. Turn off the engine, exit the vehicle and close and lock all doors, hood lid and trunk lid. The dash mounted LED begins to ash rapidly, indicating 30 second passive arming has begun.2. Opening any protected entry point during the 30 second passive arming cycle will immediately suspend automatic arming and the 30 second passive arming cycle will restart when all doors are closed. At the end of the passive arming cycle; The dash mounted LED begins to ash slowly. Parking Lights ash one time. Siren sounds one chirpIf the siren did not sound when arming, then the chirps have been turned off and you should refer to the section titled “ELIMINATING THE ARM / DISARM CHIRPS“ in this manual. Doors Lock - OptionalDoor locking during passive arming is a selectable feature. The alarm can be pro-grammed to allow the doors to lock only when arming using the keychain transmitter and they will not automatically lock during passive arming. PROTECTION WHILE THE SYSTEM IS ARMED Opening any protected door, hood or trunk lid will cause the alarm to immediately sound. The alarm will continue to sound for 30 seconds, then stop and continue to monitor all protected entry points. If the thief left a door opened, the alarm will sound for six 30 second cycles, remain armed and ignore that triggered zone.\ Whenever the system is armed, the dash mounted LED indicator will slowly ash. This serves as a visual deterrent to the potential thief. The LED is a very low current bulb and will not cause the vehicle’s battery to drain, even when left unattended for extended periods. Whenever the system is triggered, the vehicle’s parking lights will ash for the full 30 second alarm cycle, attracting visual attention to the vehicle. Optional - Whenever the system is armed, the vehicle’s starting circuit will be bypassed. If the thief should choose to ignore the siren, the vehicle can not be started. Any mild impact to the vehicle’s glass will cause the alarm to sound a short series of warning tones. Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full 30 second alarm cycle.NOTE: If the optional interior illumination circuit was installed, the interior light will ash as well for the full 30 second alarm cycle.DISARMING THE SYSTEMNOTE: If the optional 2 step door unlock circuit is installed, when the unlock
128-9309 of 6 of 24Page 6transmitter button is activated, the drivers door only will unlock, pressing theunlock button a second time will cause all doors to unlock. NOTE: If your transmitter has been congured with single button Lock/Unlock, toactivate the all door unlock feature press the Lock/Unlock button a secondtime within 3 seconds of the rst unlock command. 1. As you approach the vehicle, press and release the Unlock/Disarm button on the keychain transmitter. The dash mounted LED turns off.The LED will start ashing rapidly, indicating that the system is re-arming automatically. Open any door to suspend the automatic arming. Parking Lights ash two times.If the parking lights ashed three times, then the alarm was triggered in yourabsence. Before turning the key on, examine the LED to identify which zone was triggered.  Siren sounds two chirps.If the siren sounds 4 chirps, then the alarm was triggered in your absence. Before turning the key on, examine the LED and refer to the INTRUSION WARNING SIGNALS section of this manual to identify which zone was triggered.If the siren did not sound when disarming, then the chirps have been turned off and you should refer to the section titled “ELIMINATING THE ARM / DISARMCHIRPS“ in this manual. Doors Unlock - Optional 2 Step Doors Unlock - OptionalNOTE: If the optional Headlamp illumination feature has been added and hasbeen selected for operation when disarming, as an added convenience, thesystem will turn on the headlights when the system is disarmed. SILENT DISARMING (Feature must be activated during programming)During step 1 above, hold the transmitter button for 2 seconds then release. The unit will arm without the chirps for this one lock cycle.WHILE THE SYSTEM IS SOUNDINGIf during a triggered state, you wish to shut off the siren without disarming your security system, simply press and release any transmitter button other than the Unlock/Disarm button. This action will turn off the siren yet leave the vehicle fully armed and protected. This feature is particularly useful if you are aware of children playing near your vehicle that may accidentally trigger your security system. In this case you can cancel the siren sounding without disarming your alarm.
128-93097 of 24Page 7INTRUSION WARNING SIGNALSThis system will inform you if an intrusion attempt has occurred while you were away from the vehicle. If an intrusion attempt has occurred, the siren will chirp 4 times and the parking lights will ash 3 times when disarming the system. Enter the vehicle and observe the red dash mounted LED to identify which zone was triggered. If the LED is ashing one time...pause...one time...pause...etc., then an intrusion attempt was made to the shock sensor, or an accessory triggering device that may have been added to the system. If the LED is ashing two times...pause...two times...pause...etc., then an intrusion attempt was made to a hood or trunk pin switch that was added to the system or to a light activated entry point if the alarm was installed using the voltage sensing feature. If the LED is ashing three times...pause...three times...pause...etc., then an intrusion attempt was made through one of the vehicle’s doors.These intrusion warning indicators are stored in the system’s memory and will only be erased when the ignition key is turned on.PUSH BUTTON LED RECEIVER VALET/OVERRIDE/SAFETY SWITCHThe Push Button LED switch located in the receiver allows you to temporarily bypass all alarm functions, eliminating the need to hand your transmitter to parking atten-dants or garage mechanics. When the system is in valet mode, all alarm functions are bypassed, however the remote panic feature and remote door locks will remain operational. To use the valet mode, the system must rst be disarmed either by using your keychain transmitter, or by activating your personalized manual override code.1. Enter the vehicle, and turn the ignition key to the on position.2. Press and hold the Push Button switch until the LED turns on solid. The system will remain in the valet mode.3. To return to normal operation, press and release the Push Button switch any time the ignition is on.NOTE: Always remember to return the vehicle to the valet off position. This will ensure that the vehicle remains protected at all times. MANUALLY OVERRIDING YOUR SYSTEM: USING THE RECEIVERS PUSH BUTTON OVERRIDE SWITCHYour Security System can be disarmed without the use of the keychain transmit-ter. This is necessary, since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails. If your system has been selected for Valet Switch manual override as indicated on the last page of this manual, to bypass the alarm system;1. Open the vehicle door. The alarm will sound.2. Turn the ignition key to the ON position.3. Within 5 seconds, press and release the push button override switch.The alarm system will stop sounding and enter the (bypassed) mode. You can now start and operate the vehicle normally.Typically this override mode is used only if the transmitter has become inoperative.
128-9309 of 8 of 24Page 8PROGRAMMING YOUR CUSTOM OVERRIDE CODEUnlike override switches easily found, and defeated, this security system allows the consumer to program a personal override code, offering a higher level of security. To take advantage of this option, programmable feature # 9 must be selected for the Custom Code Option. Consult your installation center for programming details. The system comes from the factory with a pre-programmed override code of 11. To change this default override code, do the following:1. Disarm the system by use of the transmitter, or by use of the emergency override sequence. Turn the ignition switch to the on position.2. Within 10 seconds, press and release the Receivers push button switch, 3 times.3. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will beep and the lights will ash one time.)4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and re-leasing the Receivers push button switch from 1 up to 9 times.5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off then on.6. Within 10 seconds, begin to enter your chosen units digit by pressing and re-leasing the Receivers push button switch from 1 up to 9 times.7. Finish by turning the ignition switch to the OFF position. If the new code was accepted, the unit will report back the newly entered code, by ashing the LED, rst indicating the 10ths digit, pause and then the units digit. The unit will report the new code three times with a one second pause between each code, then the system will begin arming. If the LED ash pattern reports the previously stored code, the new code was not entered correctly. Please repeat steps 1 through 7 above considering the following.NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0 (Zero), or no digit entered in any place, units or tenths.NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then 5 seconds during any of the above steps, the unit will revert back to the last successfully stored code.CUSTOM CODE PROGRAMMING EXAMPLETo Change the code from the factory pre-assigned code of 11 to “52” you would do the following:1. Disarm the system by use of the transmitter, or by use of the emergency override sequence. 2. Turn the ignition switch to the on position. 3. Within 10 seconds, press and release the Receivers push button switch, 3 times.4. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will beep and the lights will ash one time.)5. Within 10 seconds, begin to press and release the Receivers push button switch to set the tenths digit. (As per the example, press and release 5 times to set the tenths digit to 5)6. Within 10 seconds of the last press of the pushbutton, turn the ignition switch off then on.7. Within 10 seconds, begin to press and release the Receivers Push button switch to set the units digit. (As per the example, press and release 2 times to set the units digit to 2).8. Turn the ignition switch to the off position. Immediately observe the LED ash pattern.
128-93099 of 24Page 9You will notice the LED ashing ve times, pause, and then ash two times, pause. This pattern will be repeated three times indicating the new code (52) has been accepted and stored in memory.NOTE: If after step 7, the LED ashes a code other than what was just entered, this indicates that the code has not been changed. You will have to repeat steps 1 through 7 above being certain to note the following: Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0 (Zero), or no digit entered in any place, units or tenths.NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then 5 seconds during any of the above steps, the unit will revert back to the last successfully stored code. MANUALLY OVERRIDING YOUR SYSTEM: USING THE CUSTOM CODE OVERRIDEAssuming the override code programmed has not been changed, and the default override code of 11 is in the system's memory.1) Enter the vehicle and turn the ignition switch to the on position.NOTE: The siren will sound.2) Within 5 seconds, press and release the Receivers push button switch 1 time.3) Within 5 seconds, turn the ignition switch off then on.4) Within 5 seconds, press and release the Receivers push button switch 1 time.5) Turn the ignition switch off then on and start the vehicle. NOTE: If you have changed the programmed override code then substitute your new code tenths for step 2 above, and units for step 5 above. ELIMINATING THE NORMAL ARM/DISARM CHIRPSYou can selectively eliminate the normal arm and disarm chirps by holding the transmitter button slightly longer when arming or disarming. This will prevent the siren chirps for one arm or disarm cycle. If you nd this inconvenient and wish to eliminate these chirps permanently,1. Turn the ignition switch 'on" then 'off".2. Within 10 seconds of turning off the ignition, press and release the Receivers push button switch 3 times.3. If the chirps were on before you started, the siren will emit 2 short chirps indicating that the chirps are now off. If the chirps were off before you started, the siren will emit one short chirp indicating that the chirps are now on.NOTE: If the vehicle battery is disconnected then reconnected, the unit will return to the default setting of chirps on. Repeat the above procedure to eliminate the arm/disarm chirps.NOTE: Your system must be programmed by the installation center to enable this feature. NOTE: Whenever the chirps are bypassed, the 4-chirp intrusion indicator and 3 chirp defective zone indicator will always operate. Since these are important warnings to you that something has happened, they cannot be eliminated.NOTE: Your system must be programmed by the installation center to enable this feature.
128-9309 of 10 of 24Page 10 REMOTE PANIC OPERATIONThe Lock or Unlock button on your keychain transmitter also functions as a panic switch for use in emergency situations. To use remote panic:1. Press and hold the Lock or Unlock button on the keychain transmitter for 3 or more seconds. The alarm will immediately sound.2. To stop the alarm, press and hold the Lock or Unlock button on the transmitter again for 3 seconds. If the button is not pressed, the alarm will automatically stop after 30 seconds. Also if any transmitter button other than the Lock or Unlock button is pressed and released, the Panic mode will be turned off immediately. The normal function of this transmitter button will be suspended during the Panic sounding period.3. During the panic mode, the Lock and Unlock buttons can be used to lock and unlock the doors, (if the option is installed), however once the unlock/disarm button is pressed, the vehicle's starter inhibit device, (where installed) will be disabled allowing the vehicle to start.NOTE: While in the Panic mode, pressing and releasing the Lock or Unlock buttons will, if the option is installed, lock and unlock the doors respectively. While in the panic mode, anytime the Unlock button is pressed, the panic feature will continue for the allotted 30 seconds, however, the security system will be disarmed allowing the vehicle to start. RF SHOCK SENSOR MODE SELECTIONThe way in which your alarm system reacts to threatening vibrations, created by attempts to enter the vehicle by breaking a window, is adjustable by the transmitter immediately after arming. There are 4 modes of operation that can be selected by the operator: 1. Normal Operation (default mode) In this mode, any strong vibrations will cause the siren to sound (full detect) for 30 seconds. Any lesser vibration will cause the siren to emit about 6 short warn away chirps, (pre-detect). 2. Stage 1 (Omit pre-detect) In this mode, the warn away chirps created by the lesser vibration will be deleted. If strong vibration occurs, the siren will sound. 3. Stage 2 (Omit pre & full detect) In this mode, both the pre-detect stage and the full trigger stage of the sensor are defeated. The unit will not react to vibration of any magnitude.NOTE: Shock Sensor Icon Is Displayed On The LCD Panel. 4. Stage 3 (City Mode) In this mode, the pre-detect chirps will change from six pre-warning tones to a full 10 seconds of warning chirps. The full detect trigger duration will be reduced from 30 seconds to 15 seconds.NOTE: Setting the stage of the shock sensor will be effective for one arming cycle only. Once the system has been disarmed, the very next arming cycle will cause the sensor to default to the normal operation stage.To change or adjust the shock sensor, press and release the ARM button of you keychain transmitter.
128-930911 of 24Page 11 1. Within 2 seconds of arming, press and release the ARM button 1 time, to defeat the pre-detect stage of the shock sensor. (The lights will ash and the siren will chirp once.) 2. Within 2 seconds of step 1, press and release the ARM button 2 times, to defeat the pre and full detect stages of the shock sensor. (The lights will ash and the siren will chirp twice.) 3. Within 2 seconds of step 1, press and release the ARM button 3 times to enter the "City Mode" of operation. (The lights will ash and the siren will chirp three times.)While under control of the remote start the system can be programmed to allow you to shunt the shock sensor from the transmitter. If the system has been programmed, simply press the lock button of your keychain transmitter anytime during the remote start cycle. The shock sensor will be shunted for the entire run cycle and will resume normal operation after the remote start unit shuts off.Check with your installation center to determine if this feature has been programmed into your system. PUSH-BUTTON LED RECEIVER SAFETY CONTROL SWITCHThe Push-Button LED control switch allows you to temporarily disable the remote starting function of the system. This recommended whenever the vehicle is being serviced. To place the system in the service mode:1) With the system disarmed/unlocked, and the ignition switch off press and hold2) Turn the ignition switch on, off, on, off, on, off.3) The LED begins to ash two short ashes followed by one long ashes and continues this pattern until returned to normal mode of operation. This puts the unit into the R/S Override mode indicating that the remote start is in the service mode and will not start from RF or any other input Posse or otherwise.To Exit R/S Override Mode1) With the system disarmed, press and hold the push button, found on the wind-shield receiver, in.2) Turn the ignition switch on, off, on, off, on, off.3) The LED turns off indicating that the R/S unit is fully functional one again. REMOTE STARTING THE VEHICLEThe system WILL NOT start the vehicle if any one of the following conditions exists: 1. The Vehicle Hood Is Opened. 2. The Gear Selector Is In Any Gear Other Then Park. 3. The Brake Is Depressed. 4. The Safety Control Switch Is In The Off Position. WARNING! Be certain that the vehicle is outdoors before using this or any remote vehicle starting device. A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs. DO NOT remote start the vehicle if it is garaged.
128-9309 of 12 of 24Page 12 TO REMOTE START THE VEHICLEPress and release the programmed channel of your keychain transmitter two times within 2 seconds. The vehicle will start and remain running for the pre-programmed 5, 10, 15, or 20 minutes. As a visual indication, the parking lights will ash or turn on depending on the programming set up by your installation center. When you arrive at your vehicle, disarm the alarm system by pressing and releasing the arm/disarm button of your keychain transmitter. Enter the vehicle and turn the ignition key to the on position. NOTE: This system has the ability to be congured to a single press start if you so desire. Please check with your installation center if your system was changed from the default safe start setting of two press start or if you wish to change your conguration. WARNING! Do not turn the key to the start position. This will cause the starter motor to engage with the already running engine which could result in damage. Step on the brake pedal to disengage the remote start unit. The vehicle will continue to run but now on it's own power. NOTE: The engine will stop running before the expiration of the pre-programmed run timer if you complete any of the following: 1. Press and release the programmed channel of your keychain transmitter two times within 2 seconds. 2. Depress the brake pedal. 3. Open the hood. 4. Move the red handled control switch to the off position. 5. Race the engine to above 4000 RPM. OPERATING ON AUTOMATIC START UP TIMER MODEYour system has the ability to automatically start the vehicle every 2 or 4 hours over a 48 hour period. This feature is especially useful in cold climates where the only means to keep the engine and engine uids warm is to periodically start the engine.WARNING! Be certain that the vehicle is outdoors before using this or any remote vehicle starting device. A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs. DO NOT remote start the vehicle if it is garaged. TO BEGIN THE AUTOMATIC START UP TIMER 1. Turn the ignition key on then off. 2. Within 10 seconds, activate the RF start command two times. (Push the pro-grammed channel button of your keychain transmitter 4 times).The parking lights will ash and the siren will chirp 4 times indicating the timed start mode is activated.The vehicle, on a 2 or 4 hour interval basis, will automatically start, run for the pre-programmed time (5,10,15 or 20 minutes), and then shut off. This will continue for 48 hours. NOTE: The automatic start up timer can also be initiated from the keychain trans-mitter. To do this:
128-930913 of 24Page 13 1. Start the vehicle using the keychain transmitter by pressing and releasing the second channel transmitter button 2 times. 2. Shut off the vehicle using the keychain transmitter by pressing and releasing the second channel transmitter button 2 times. 3. Within 10 seconds of step 2, activate the RF start command two times. (Push the second channel button of your keychain transmitter 4 times).The parking lights will ash and the siren will chirp 4 times indicating the timed start mode is activated. CANCELING THE AUTOMATIC START UP TIMERTo cancel the automatic start up timer do one of the following; 1. Start the vehicle manually with the use of the ignition key and depress the brake pedal. 2. Remote start the vehicle using your keychain RF transmitter. NOTE: Option button used in combination is only available on the alternate remote transmitter and not available on the LCD Transmitter. OPTIONAL DEVICE OUTPUT ( CHANNEL 3 )Controlled By: Trunk/Key Button Other Transmitter button congurations are also available. Consult your installation center for other congurations not listed above that may have been programmed to operate a specic feature of your system. This security system is equipped with an output which will activate when the ap-propriate transmitter button is depressed for 4 seconds. Although this output is intended to activate the trunk release option, any other optional devices may be connected to this channel. Consult your installation center for more information about this output. ADDITIONAL REMOTE FUNCTION ( CHANNEL 4 )Controlled By:  Trunk/Key Button  Option Button  Lock + Unlock Buttons  Lock + Trunk/Key Buttons  Unlock + Trunk/Key Buttons Other Transmitter button congurations are also available. Consult your installation center for other congurations not listed above that may have been programmed to operate a specic feature of your system. This security system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are; Remote Car Starter Remote Window Closure Remote Garage Door InterfaceTo remotely operate the device indicated, momentarily press, or press and hold the appropriate transmitter button(s) as indicated above. ADDITIONAL REMOTE FUNCTION ( CHANNEL 5 )Controlled By:  Trunk/Key Button  Option Button  Lock + Unlock Buttons  Lock + Trunk/Key Buttons  Unlock + Trunk/Key Buttons
128-9309 of 14 of 24Page 14Other Transmitter button congurations are also available. Consult your installation center for other congurations not listed above that may have been programmed to operate a specic feature of your system. This security system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are: Remote Car Starter Remote Window Closure Remote Garage Door InterfaceTo remotely operate the device indicated, momentarily press, or press and hold the appropriate transmitter button(s) as indicated above. ADDITIONAL REMOTE FUNCTION ( CHANNEL 6 )Channel 6 is an alternate output that can be controlled by the unlock button of the transmitter, or by and independent button or combination of buttons. For your vehicle this output is: Controlled By:  Trunk/Key Button  Option Button  Lock + Unlock Buttons  Lock + Trunk/Key Buttons  Unlock + Trunk/Key Buttons Other Transmitter button congurations are also available. Consult your installation center for other congurations not listed above that may have been programmed to operate a specic feature of your system. This security system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are: Remote Car Starter Remote Window Closure Remote Garage Door InterfaceTo remotely operate the device indicated, momentarily press, or press and hold the appropriate transmitter button(s) as indicated above. ADDITIONAL REMOTE FUNCTION ( CHANNEL 7 )Channel 7 is an alternate output that can be controlled by the unlock button of the transmitter or by any independent button or combination of buttons. For your vehicle this output is:Controlled By:  Trunk/Key Button  Option Button  Lock + Unlock Buttons  Lock + Trunk/Key Buttons  Unlock + Trunk/Key Buttons
128-930915 of 24Page 15Other Transmitter button congurations are also available. Consult your installation center for other congurations not listed above that may have been programmed to operate a specic feature of your system. This security system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are: Remote Window Closure Remote Garage Door InterfaceTo remotely operate the device indicated, momentarily press, or press and hold the appropriate transmitter button(s) as indicated above. TURBO TIMER MODEThis system provides a means to cool down the vehicles turbo charger, if so equipped, by allowing the vehicle to continue to run for a prescribed period of time every time the vehicle's engine is turned off. This feature requires the system to be set up for turbo timer during installation. Consult with your installation center to be certain this feature was activated and how long the vehicle will continue to run, 3, 5, or 10 minutes after the ignition switch is turned off.To activate the turbo timer:Anytime the engine is running for more than 15 seconds:1) Place the gear selector in park.2) Set the parking, (hand), brake.3) Be certain your foot is off the brake pedal.4) Press the receiver's program/Push-Button switch 2 times within 5 seconds. The parking lights will ash two times indicating the mode was successfully entered.If your parking lights ashed four times, this indicates the turbo mode was on and is now turned off.With the turbo timer mode selected on, after you've arrived at your destination, while the engine is still running, set the parking brake, pause 2 seconds, then turn the ignition switch to the off position. The engine will continue to run the allotted time according to the selection during installation.If you do not want the vehicle to continue to run for one cycle, simply step on the vehicle's brake, or release the parking brake, or activate the transmitter's start button two times in succession. Any of these will cause the engine to turn off. TELEMATIC UPGRADEThis system has the ability to have a Telematic Upgrade module connected to it. This is a upgrade that can give you control of certain functions of your vehicle from a Telephone, or in some cases a computer interface. Please check with your installation center for most recent Telematic Upgrades. If you had a Telematic Up-grade installed, the manual supplied with the upgrade unit will provide a operators manual advising of the features of the system and means available to control these features of your vehicle. TRANSCEIVER ICONS AND THEIR INDICATIONSRefer to the LCD Transceiver Located On Page 18 and it's call outs which will be referred to in the following feature descriptions.
128-9309 of 16 of 24Page 16When Disarmed, Press the Arm/Lock button to Lock and Arm the System. The Lock Icon is displayed on the LCD panel & the parking lights ash once.When Armed, Press the Disarm/Unlock button to Unlock and Disarm the System. The Unlock Icon is displayed on the LCD panel and the parking lights ash twice. When the Key Icon Button Has Been Operated for 3 seconds the trunk open icon will ash on the LED Screen. When the Key Icon Button is pressed 2 times in succession The reverse circle is displayed on the LCD screen while the vehicle is running. This icon will ash and the hour glass will indicate count down timer based on the run time set up by your installation center. When the unit shuts off the Icon will turn off and the transmitter will play a melody. NOTE: Engine can be started in many modes armed, disarmed, valet, etc. The screen will display multiple icons indicative of these modes. When the Panic Mode has been activated and the system is armed the vehicle's lights will ash, the siren and lock icon will be displayed on the LCD screen and the siren will beep. If the system is disarmed and the Panic Mode is activated, the lights will ash unlock icon will be displayed and the siren will beep on the LCD screen. TURNING OFF BEEP TONES AT THE TRANSCEIVERWhen ever the vehicle is operated from the two way transmitter, the unit will beep responsive to the function executed at the vehicle. 1 beep when armed, 2 beeps when disarmed, etc. at times it may be inconvenient or too noisy to hear the beep tones, so the system allows you to set the unit for vibrate mode.To toggle on or off beep tones/vibrate, simultaneously press the "F" and unlock buttons. The icons shown left will appear in the upper left hand corner of the screen to indicate vibrate..If the alarm system has been triggered, the icon displayed on the LCD transmitter will indicate which zone has been activated, as well sound the beep tones, or vibrate dependent upon the setting as shown above. The following trigger patterns will be displayed.Triggered and the entry attempt was made to one of the vehicle Doors.Triggered and entry attempt was made to the vehicles Hood or Trunk.
128-930917 of 24Page 17ATriggered and entry attempt was made to the vehicles glass, or the ve-hicle has been hit or bumped hard enough to cause a response from the vibration detector. ADDITIONAL ICONS THAT MAY BE DISPLAYED ARE:If the arm/disarm chirp tones have been turned off at the vehicle, when you arm, or disarm, the display will indicate this as shown and there will be no arm/disarm chirps at the transmitter. This is true if the transmitter is set for vibrate mode as well.When the vehicle is armed, and a door is opened, or ajar, the transmitter will chirp 3 times, the lights will ash, and the display will indicate a door trigger as shown above. When the door is closed or the zone clears, the transmitter will chirp 1 time, and the display will clear. When the vehicle is armed, and the hood or trunk, is opened or ajar, the trans-mitter will chirp 3 times, the lights will ash, and the display will indicate a hood or trunk trigger as shown on the previous page. When the hood or trunk is closed, or the zone clears, the transmitter will chirp 1 time, and the display will clear. PROGRAMMED TRANSMITTER NOTIFICATION (PTN) Every time after Disarm when the ignition key is turned on, the unit's LED will report the number of transmitters programmed into the system. This safety feature will alert you if an unauthorized transmitter has been programmed into your vehicle's security system without your knowledge. Typical from the factory, there will be a 2 ash, pause, repeated 3 times indicating that two transmitters are programmed into the system. If you note additional ashes, there may have been an additional transmitter added without your knowledge or authorization. If you notice a change in the transmitter LED report pattern, you can correct this by looking up how to erase and reprogram your transmitters found in the transmit-ter programming guide. This reprogram operation will erase all unauthorized or unwanted transmitters.
128-9309 of 18 of 24Page 18PRESTIGEIGNAMPMZZ24S1 2INHIBITA0Lock/Arm Unlock/DisarmTrunk Release/ Remote StartOptionFFunction Button24 ADDITIONAL REMOTE FEATURES:The two way remote control unit allows you to access status information from the vehicle, check temperature, light the display, toggle the transmitter from beep tones to vibrate mode, initiate daily start timer, and temperature start. Selection of these and other features are shown below:NOTE: Transmitter must be within operating range of the vehicle, approximately 5000ft. Check Vehicle StatusPress the lock+key+option buttons simultaneously for 1 second. The vehicle's alarm will display the systems current status. Check Temperature (Only available on certain remote start units)Press the option+key buttons simultaneously for 1 second. The vehicle's alarm will display the temperature. Temperature is read from the alarm's module located below the dashboard. This reading may be higher than actual ambient temperature due to the greenhouse effect and is relative only to the inside vehicle temperature.Temperature Start Mode (Available on certain models)To toggle this feature on or off, from the armed mode, press the Option & Unlock Buttons simultaneously, the temperature icon appear on, or disappear from the display, and the transmitter will emit a tone. NOTE: This feature must be active in the feature selection menu of your system. Check with your installing dealer to ensure this feature is set to the on position.Light The DisplayPress and release the "F" (Function) button one time. The display will illuminate for 10 seconds.Vibrate Or TonesPress the "F" and unlock buttons simultaneously to toggle this feature on and off.Daily Start Timer (Only available on certain remote start units)24 Hour Start Timer. Standing at the vehicle at the time you want it to start, press the option + lock buttons simultaneously for 1 second. The transmitter will beep and display the 24 hr timer. This is the time the vehicle will start when you follow the exit procedure. In other words, if you want the vehicle to start 6AM, at 6AM of any morning, standing at the vehicle, press and hold the option + lock buttons until you hear a beep and the 24 hr timer is displayed. This establishes a starting time. The Remote Start unit will start at the prescribed time once only. This function must be activated by following the procedure below each time you want the vehi-cle to start at the prescribed time.
128-930919 of 24Page 19To activate this function, (a) Turn the ignition switch off. (b) Within 10 seconds of step (a), depress and hold the brake pedal, while press-ing the key icon transmitter button 2 times. (c) The unit will emit 2 chirps, the transmitter will beep and the 24 Hour start timer icon on the display will remain on. The vehicle will start at the set time 24 hours from when set. To toggle this feature off, press the option + lock buttons simultaneously until a beep is heard and the 24 hr timer turns off.NOTE: The unit will start once and run for the prescribed time. If you require more frequent starting please refer to auto start up timer mode shown earlier in this guide. NOTE: To insure accurate 24 Hour Start up, it is advisable to reset the start time periodically as time may drift slightly each day. Timing Count DownThe unit offers an additional count down timer for situations where an alert tone may be needed to remind you of something important. For instance you may have a meeting 4 hours from now and you want a reminder in 3 Hrs and 45 Mins. This additional count down timer allows you to set the count down up 19 Hours and 59 Minutes from the current time and when the timer reaches zero, the transmitter will emit a tone or vibrate depen-dent on your preferred setting. See chart for setting the count down time for this feature. ValetWhen the System is in the valet mode, the icon shown will show in the display when the status check buttons are activated.Parking Meter CounterThe transmitter has a built in clock that can count down from 10, 20, 30, 60, 90, or 120 minutes. This feature is useful when parking the vehicle in a metered parking lot. If the time on the parking meter is 30 minutes, you can set the count down timer to 20 minutes. The transmitter will emit a beep tone when the timer expires to remind you to get back to your vehicle. See following chart for setting the parking meter count down timer feature. Alarm Clock ModeThe transmitter has a built in alarm clock that can be set to beep at a cer-tain time each day. The alarm clock mode must be set, and the feature turned on. To use this feature please refer to the chart on the following page.NOTE: Your system is shipped with two transmitters, 1 two way, shown on the left and the one way transmitter, shown right. The one and two way transmitters are programmed from the factory with separate lock & un-ZZ
128-9309 of 20 of 24Page 20lock buttons, the trunk/key icon button operates remote start and remote trunk release where ap-plicable. The option button and any button com-bination may be programmed to operate various options. Consult your installation center for button programming and options that may have been added to your vehicle. Although this is the default programming from the factory, this can be changed for you to any conguration you prefer. Please refer to the transmitter program guides included with your kit.NOTE: A maximum of two of either style transmitter may be programmed to your unit.BATTERY INDICATOR Your transmitter has a battery indicator that is shown in the upper right corner of the screen as shown left. This icon indicates a new battery shown with 3 bars. As the battery deteriorates, the bars will disappear. bar indicates the battery should be replaced. Replace battery with a fresh 1.5V AAA battery and dispose of the used battery properly.Other icons that will be displayed at times when certain functions and features are active in the vehicle or on the remote.RANGE INDICATOR The range indicator will have bars to the side of the icon if the unit is out of range.VIBRATE MODE ON This icon will be displayed if you select vibrate instead of tones. To toggle vibrate on and off, press "F" + Unlock simultaneously.ALARM CLOCK This icon will be toggled on and off when the "F" + Trunk/Key buttons are pressed simultaneously. The feature must be set in the feature selection menu of the transmitter.COUNT DOWN TIMER The unit offers an additional count down timer for situations where an alert tone may be needed to remind you of something important. Setting information shown on previous page. POWER SAVE FEATURE Press the "F" and Lock buttons simultaneously to toggle this feature on and off. With this mode on, the battery in the transmitter will go into a power down mode when the unit is disarmed.PRESTIGEIGNAMPMZZ24S1 2INHIBITA0PRESTIGE1 2S
128-930921 of 24Page 2124 24 HOUR START TIMER Standing at the vehicle at the time you want it to start, press the option + lock buttons simultaneously for 1 seconds. The transmitter will beep and display the 24 hr timer. This is the time the vehicle will start when you fol-low the exit procedure. In other words, if you want the vehicle to start 6AM, at 6AM of any morning, standing at the vehicle, press and hold the option + lock buttons until you hear a beep and the 24 hr timer is displayed. This establishes a starting time. The unit will start at the prescribed time once only. This function must be selected each time you want the vehicle to start. To activate this function:(a) Turn the ignition switch off. (b) Within 10 seconds of step (a), depress and hold the brake pedal, while pressing the key icon transmitter button 2 times. (c) The unit will emit 2 chirps, the transmitter will beep and the start timer icon on the display will remain on. The vehicle will start at the set time. To toggle this feature off, press the option + lock buttons simultaneously until a beep is heard and the 24 hr timer turns off.TEMPERATURE START MODEThis icon will appear when the temp start mode is activated. The vehicle will start one time automatically when the temperature reaches 0*. WARNING! Be certain vehicle is outside before activating this mode. To toggle this feature on of off, from the Locked/Armed mode, press the Option and Lock buttons simultaneously. (Available on certain remote start models only).Throughout this manual you will nd screen shots where they apply if using the two way transmitter. If using the one way transmitter while the two way transmitter is within range of the vehicle, the two way transmitter will update it's screen.
128-9309 of 22 of 24Page 22TRANSMITTERFUNCTIONSELECTIONTRANSMITTER BUTTONICON DISPLAYEDTONE/VIBRATETIMING ADJUST MODE (HRS)TIMING ADJUST MODE (MINS)ALARM CLOCKADJUST MODE (HRS)ALARM CLOCKADJUST MODE (MINS)ALARM CLOCK & POWERUP MUSIC SELECTTIMING COUNT DOWNADJUST MODE (HRS)TIMING COUNT DOWNADJUST MODE (MINS)TIMING COUNT DOWNEND MELODY SELECTIONTIMING COUNT DOWNMODE SELECT ON/OFFREMOTE START ONMELODY SELECT 2ALARM CLOCK ADJUSTMODE ON/OFFFFFFFFFFFFFPRESS FOR5 SECONDSPRESS 1XPRESS 2XPRESS 3XPRESS 4XPRESS 5XPRESS 6XPRESS 7XPRESS 8XPRESS 9XPRESS 10X 5 8AMPM 18:88AMPM 18:88AMPM 18:88AMPM 18:88AMPM 18:888ON/OFFAMPM 18:888ON/OFF2 BEEP TONES5 SELECTIONS PRESSKEY BUTTON OR OPTIONBUTTON TO SELECT5 SELECTIONS PRESSKEY BUTTON OR OPTIONBUTTON TO SELECT5 SELECTIONS PRESSKEY BUTTON OR OPTIONBUTTON TO SELECTTRANSMITTERFUNCTIONOPERATIONTRANSMITTER BUTTONS TOPRESSICON DISPLAYEDTONE/VIBRATE10 MIN PARKINGCOUNT DOWN TIMER FFFFFFFFFFF0:200:101:000:300:00ON/OFFMELODY20 MIN PARKINGCOUNT DOWN TIMER30 MIN PARKINGCOUNT DOWN TIMER60 MIN PARKINGCOUNT DOWN TIMER90 MIN PARKINGCOUNT DOWN TIMER120 MIN PARKINGCOUNT DOWN TIMERPARKING COUNT DOWNTIMER OFF MODEBACKLIGHT DISPLAYFOR 10 SECONDSVIBRATE/TONE SELECTALARM CLOCK MODESELECT ON/OFFFAHRENHEIT/CELSIUSSELECTPOWER SAVE MODE F+ OPTION 1X+ OPTION 2X+ OPTION 3X+ OPTION 4X+ OPTION 5X+ OPTION 6X+ OPTION 7X1XPRIMARY OR SECONDARY VEHICLE ON/OFFTRUNK/KEY + LOCK BUTTON 5 SECONDS 1 OR 22:001:30MELODYMELODYMELODYMELODYMELODYMELODYILLUMINATESDISPLAYVIBRATES 4 TIMESOR BEEPS 1XMELODYMELODYMELODYMELODYF OR C+ + OPTION 1X+ KEY 1XS+1X+1X
128-930923 of 24Page 23APS 997ESYSTEM FUNCTIONS AT A GLANCEDASH LED INDICATORSRAPID FLASHING = PASSIVE ARMING/ACTIVE REARMINGSLOW FLASHING = ARMEDOFF = DISARMEDON SOLID = VALET MODE3 FLASH...PAUSE = INTRUSION ZONE 32 FLASH...PAUSE = INTRUSION ZONE 21 FLASH...PAUSE = INTRUSION ZONE 1SIREN CHIRP INDICATORS1 CHIRP * = ARM2 CHIRPS * = DISARM3 CHIRPS = ARM / DOOR OPENED4 CHIRPS = DISARM / INTRUSION* These chirps are optional, and can be de - activated.PARKING LAMP INDICATORS1 FLASH = ARM2 FLASHES = DISARM3 FLASHES = DISARM / INTRUSIONFCC COMPLIANCEThis device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada.Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including any interference that maycause undesired operation.Warning!Changes or modications not expressly approved by the party responsible forcompliance could void the user’s authority to operate the equipment.NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this equipment. Such modications could void the user’s authority to operate the equipment
128-9309 of 24 of 24Page 24© 2014 Voxx Electronics Corporation. 150 Marcus Blvd. Hauppauge, NY 11788 128-9309To purchase replacement transmitters or to get additional product information go to: www.prestigecarsecurity.comPATENTED: www.voxxintl.com/company/patentsPROGRAMMING NEW OR REPLACEMENT TRANSMITTERS (BANK 1)Transmitter Model Name 145SP or 5BCR14SP Is Also Found On Back Of Transmitter Case. Use Battery CR2032 For 145SP & AAA For 5BCR14SP. 1) Turn the ignition key to the on position.2) Press and release the valet/programming switch 3 times (Siren Chirps).3) Press the Lock Button of each transmitter you want programmed until you hear a chirp from the horn or siren.4) Turn the ignition switch off.The above action programs the Lock, Unlock, Start/Trunk, and Option 1 buttons which are typical for most systems. For additional channel programming beyond the option 1 button, you can use any unused button or combination of buttons not in use. In other words, to access option channel 5, 6, 7, you would do the following:From step 3 above: a) Press and release the valet/programming button 4 additional times to get to channel 5, then press any unused transmitter button or button combination to program.b) From a, press and release the valet/programming button 1 time to get to channel 6, then press any unused transmitter button or button combination to program.c) From b, press and release the valet/programming button 1 time to get to channel 7, then press any unused transmitter button or button combination to program.NOTE: Not all systems have channels above 3, check with your installation center for options your system may or may not have.NOTE: Certain systems have the ability to utilize channels 6 & 7 for driver priority programming. For driver priority, the vehicle must be equipped with this feature, and the optional feature must be set up and installed by your installation center. Once this feature is added when the unlock button of transmitter 1 is used, it will set driver 1 priority, and when the unlock button of transmitter 2 is used it will set driver 2 priority. In this situation, the unlock button can be programmed into two receiver channels, unlock, channel 2 and driver priority 6 or 7. In no other circumstance will the system allow a transmitter button to be programmed into 2 receiver channels at the same time.This unit's transmitters can control two vehicles with Prestige Remote Systems. To toggle primary or secondary vehicle press trunk/key & option for 5 seconds.Transmitter Battery Replacement1) Locate and remove the "00" point Phillips head screw on the back of the transmitter case.2) Carefully separate the front case from the rear.3) Slide the CR2032 battery out from under the battery clip and dispose of properly.4) Install the new battery with the (+) side facing up away from the circuit board.5) Close the case and reassemble in reverse of disassembly

Navigation menu