Nutek NTREA Alarm Device User Manual 5bcr bcr03

Nutek Corporation Alarm Device 5bcr bcr03

Users Manual

Your Alarm and or Remote Start unit has a configurable receiver thatallows the transmitter to be programmed to operate the Lock Unlockfunctions with one transmitter button or with two transmitter buttons(separate Lock/Unlock). In addition, the receiver also allows driver priorityfunction. This driver priority function takes place when ever a particulartransmitter is used to unlock the vehicle regardless of the selection of onebutton or two button operation.The following indicates the receiver programmable slots.1 Lock/Unlock or Lock2 Unlock if Programmed3 Trunk Release & or Remote Start (Optional on some models)4 Auxiliary Output5 Auxiliary Output6 Driver 1 Priority or Sperate Output7 Driver 2 Priority or Separate OutputReceiver channels 6 or 7 will accept the programming of transmitterchannel 1 if used as the Lock/Unlock button, or Channel 2 when separateLock Unlock buttons are programmed. In this way, whenever the transmit-ter is used to unlock the vehicle, channel 6 or 7, when programmed, willprovide a pulsed ground output. This output can be connecter to the driverpriority function of the vehicle to reset preset user features. Please consultwith your installation center’s technician to see if this feature is available inyour vehicle.NOTE: A total of 4 transmitters may be programmed into any receiverchannel. Two two way and two one way or four one way transmittercombinations only.Force programming a transmitter, removing a transmitter, or re-prioritizing atransmitter is covered later in this manual.Also, if you do not program a transmitter button into channel 2 which is theseparate unlock/disarm channel, then whatever button is programmed intochannel 1 will serve as both lock/arm & unlock/disarm.Note: The “F” Button serves as a function button in combination with otherbuttons explained in your owners manual. This button may not be used tooperate a receiver channel.NOTE: The Option Button is predetermined and programmed for access toTime Start, and Temperature Start & Check so it cannot be used for multiplebutton operation of any other feature. It will however operate for any singlebutton programming.This transmitter is also capable of one button programming for certain modelAudiovox Alarms. If your alarm is one of these models, then when step 3 iscompleted on the following page, you can turn the ignition switch off andprogramming with the default button configurations for the first four channelswill be complete.Model UTX-ETXProgramming Guide
TO ENTER THE PROGRAM MODE:1. Turn the ignition switch to the “ON” position.2. Within 10 seconds, Press and release the valet/program switch threetimes.(Siren emits 1 short chirp indicating channel 1 has been entered)3. Within 10 Seconds, Press and hold the button of the first transmitter youwish to control the Lock & Arm feature of your security system until a longchirp is heard from the siren.(Repeat this for each transmitter you wish to operate the Lock/Armfeature).NOTE: If single button programming is available on your alarm system,then programming is complete at this step. You can turn off your ignitionswitch. (Check your owners manual for advise of this feature availability).4. Within 10 seconds, press and release the valet program switch onetime.(Siren emits 2 short chirps indicating channel 2 has been entered)5. Within 10 Seconds, Press and hold any unused button(s) of the firsttransmitter you wish to control the Unlock/Disarm feature of your securitysystem until a long chirp is heard from the siren.NOTE: This channel is used only if you desire separate control of theLock/Unlock feature. If you wish to operate the Lock/Unlock features froma single button, move onto step 6 as whatever button is programmed intochannel 1 will control both Lock & Arm/Unlock & Disarm.(Repeat this for each transmitter you wish to operate the Unlock/Disarmfeature).6. Within 10 seconds, press and release the valet program switch onetime.(Siren emits 3 short chirps indicating channel 3 has been entered)7. Within 10 Seconds, Press and hold any unused button(s) of the firsttransmitter you wish to control Channel 3 output, (Trunk Release) until along chirp is heard from the siren.(Repeat this for each transmitter you wish to operate the Channel 3 output(Trunk Release)8. Within 10 seconds, press and release the valet program switch onetime.(Siren emits 4 short chirps indicating channel 4 has been entered)9. Within 10 Seconds, Press and hold any unused button(s) of the firsttransmitter you wish to control Channel 4 output, (Auxiliary Output 1) untila long chirp is heard from the siren.(Repeat this for each transmitter you wish to operate the Channel 4output)10. Within 10 seconds, press and release the valet program switch onetime.(Siren emits 5 short chirps indicating channel 5 has been entered)
11. Within 10 Seconds, Press and hold any unused button(s) of the firsttransmitter you wish to control Channel 5 output, (Auxiliary Output 2) untila long chirp is heard from the siren.(Repeat this for each transmitter you wish to operate the Channel 5output)12. Within 10 seconds, press and release the valet program switch onetime.(Siren emits 6 short chirps indicating channel 6 has been entered)13. Within 10 Seconds, Press and hold the unlock button, (or any unusedbutton(s)), of the first transmitter you wish to control Channel 6 output,(Driver Priority 1) until a long chirp is heard from the siren.(Repeat this for each transmitter you wish to operate the Channel 6output, Driver Priority 1)14. Within 10 seconds, press and release the valet program switch onetime.(Siren emits 7 short chirps indicating channel 7 has been entered)15 .Within 10 Seconds, Press and hold the unlock button (or any unusedbutton(s)) of the first transmitter you wish to control Channel 7 output,(Driver Priority 2) until a long chirp is heard from the siren.(Repeat this for each transmitter you wish to operate the Channel 7output, Driver Priority 2)NOTE: Channels 6 and 7 can be used as a separate output to control afunction other than driver priority. Simply programming any unusedtransmitter button other than the unlock button will allow completeindependent control of these outputs.ERASING TRANSMITTERS IF THEY HAVE BEEN LOST OR STOLEN:NOTE: Before you begin to erase the lost or stolen transmitter(s), have alltransmitters available that you wish to remain programmed. These will beused during the program process to identify transmitters that will continueto be used.Enter the transmitter program mode:1. Turn the ignition switch to the “ON” position.2. Within 10 seconds, press and release the valet/program switch threetimes. (Siren emits 1 short chirp indicating channel 1 has been entered)3 .Within 10 Seconds, Press and hold the ARM or ARM/DISARM button ofthe first transmitter you wish to remain stored into the control unit until asingle chirp is heard from the siren.(Repeat this for each transmitter you wish to remain stored in the controlunit).The receiver stores up to four transmitters. To be certain all transmitterslots in the receiver are occupied with transmitters you wish to continueto use, and all others are erased, you will have to fill all four receiver slots.If in step 3 you identified one transmitter, you will have to fill the additional
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions. (1)This device may not cause harmful interference, and(2)This device must accept any interference received, including interference that may cause undesired operation. Per FCC 15.21, you are cautioned that changes or modifications not expressly approved by the part esponsible for compliancecould void the user’s authority to operate the equipment.

Navigation menu