Nutek NTRLG Deluxe 2-way Alarm & Remote start User Manual

Nutek Corporation Deluxe 2-way Alarm & Remote start

User manual

www.caralarm.com LIMITED LIFETIME WARRANTY  Products manufactured and sold by OMEGA RESEARCH & DEVELOPMENT (the Company), are warranted to be free from defects in materials and workmanship under normal use. If a product sold by the Company proves to be defective, the Company will repair or replace it free of charge within the first year and  thereafter all parts to be repaired will be free with only a nominal charge for Omega Research and Development’s labor and return shipping, to the original owner during the lifetime of the car in which it was originally installed.  All products for warranty repair must be sent postage prepaid to Omega Research & Development, 981 N. Burnt Hickory Road, Douglasville, GA 30134, with bill of sale or other dated proof of purchase. This warranty is nontransferable and does not apply to any product damaged by accident, physical or electrical misuse or abuse, improper installation, alteration, any use contrary to its intended function, unauthorized service, fire, flood, lightning, or other acts of God.  This warranty limits the Company’s liability to the repair or replacement of the product. The Company shall not be responsible for removal and/or reinstallation charges, damage to or theft of the vehicle or its contents, or any incidental or consequential damages caused by any failure or alleged failure of the product to function properly. Under No Circumstances Should This Warranty, Or The Product Covered By It, Be Construed As A Guarantee Or Insurance Policy Against Loss. The Company neither assumes nor authorizes any person or organization to make any Warranties or assume any liability in connection with the sale, installation, or use of this product.Please treat the 2-Way Controller with care; as with all LCD devices, it is vulnerable to mishandling damage such as impacts or dropping. Damage such as scratches, chips and normal “wear and tear”, are not a factory defect and are not covered under warranty.
AL-185X-EDPBDeluxe 2-way Alarm & Remote StartMay 29, 2013Operation GuideTemporary cover. Color cover is in a separate  le.
2Table Of ContentsController & Transmitter Overview................................................................................ 3The 2-Way Controller ............................................................................................... 3The 1-Way Transmitter ............................................................................................. 3Controller & Transmitter Functions ............................................................................... 3Other Remote Start Features ....................................................................................... 7Low Battery/Low Temp Automatic Starting ............................................................... 7Turbo Timer Feature ................................................................................................. 8Pit-Stop Feature ....................................................................................................... 8Manual Transmission Starting .................................................................................. 8Security System Features ............................................................................................ 8Last Door Arming ...................................................................................................... 8Automatic Rearming ................................................................................................. 9Pre-Warn Detection .................................................................................................. 9When The System Triggers ...................................................................................... 9Using The Valet Switch ................................................................................................. 9Emergency Override ................................................................................................ 9Valet Modes ............................................................................................................ 10SecureCode ........................................................................................................... 10The Status Light ..........................................................................................................11Multi-Car Operation .................................................................................................... 12Selecting CAR #1 or CAR #2 ................................................................................. 12Controller Options....................................................................................................... 12LCD Screen Icons .................................................................................................. 12In-Range Indicator .................................................................................................. 12Setting The Clock ................................................................................................... 13Changing remote start melodies ............................................................................ 13Power Save Mode .................................................................................................. 13Selecting Melody & Vibrate modes......................................................................... 13Parking Timer & Remote Start Timer ...................................................................... 13Button Lock ............................................................................................................ 13Anti-Carjacking Protection .......................................................................................... 14Programming Controllers/Transmitters ....................................................................... 15Programming Features ............................................................................................... 15User Programmable Features .................................................................................... 16Installer Programmable Features ............................................................................... 19Programmable Features Matrix .................................................................................. 23
3THE 2-WAY CONTROLLERController & Transmitter OverviewController part number: 154-03 (black w/ CR2032 batteries)157-03 (red w/ rechargeable battery)158-03 (black w/ rechargeable battery)1) Antenna: Sends commands to the system and receives con rmations for 2-way functions.2) LCD Display: Displays all controller func-tions as well as the status of your system.3) Control Buttons: Will light up when pressed.4) Charging Port (rechargeable models only): The buttons will  ash while charging. When  nished, the buttons will stay lit.5) Programming Button: This is used for setting controller features.12“lock”button“trunk”button“unlock”button“start”buttonTransmitter part number: 148-03 (w/o antenna & blue light)1410-03 (w/ antenna & red light)Call your dealer or visit www.caralarm.com to order replacement transmitters.Transmitter battery replacement:Remove the small screw from the  lower back case, and separate the transmitter halves. Replace the battery with the same type and reassemble the transmitter case.THE 1-WAY TRANSMITTERLOCK / ARM:  Press and release the “LOCK” button.THE SIREN WILL CHIRP & THE PARKING LIGHTS WILL • FLASH ONCE.UPON RECEIVING CONFIRMATION FROM YOUR SYS-• TEM, THE CONTROLLER WILL SHOW THE LOCK/ARM ICON AND BEEP ONCENOTE: PRESSING LOCK TWICE IN 5 SECONDS  STARTS THE PARKING TIMER. THE CLOCK WILL CHANGE TO 0:00 AND START COUNTING IN MINUTES & HOURS.(1-WAY TRANSMITTER: PRESS THE LOCK BUTTON)Controller & Transmitter Functions4533
4Controller & Transmitter Functions (cont’d)UNLOCK / DISARM:  Press and release the “UNLOCK” button.THE SIREN WILL CHIRP TWICE & THE PARKING • LIGHTS WILL FLASH TWICE THEN ILLUMINATE FOR 30 SECONDS.UPON RECEIVING CONFIRMATION FROM YOUR • SYSTEM, THE CONTROLLER WILL SHOW THE UNLOCK/DISARM ICON AND BEEP TWICE.(1-WAY TRANSMITTER: PRESS THE UNLOCK BUTTON)TRUNK RELEASE / CHANNEL 2:  Press the “TRUNK” button for 3 seconds.THE SYSTEM WILL DISARM AND THE TRUNK WILL • OPEN (IF EQUIPPED).UPON RECEIVING CONFIRMATION FROM YOUR • SYSTEM, THE CONTROLLER WILL PLAY THE TRUNK RELEASE ANIMATION AND BEEP TWICE(1-WAY TRANSMITTER: PRESS AND HOLD THE “||” BUT-TON FOR 3 SECONDS)REMOTE START:  Press and release the “    ” button twice within 5 seconds. (see user feature #17 for additional options)THE PARKING LIGHTS WILL FLASH ONCE AND THE • STATUS LIGHT WILL FLASH RAPID GREEN. THE SYSTEM WILL TURN ON THE IGNITIONS AND • PROCEED TO START THE ENGINE. ONCE THE ENGINE IS RUNNING, THE PARKING • LIGHTS WILL TURN ON AND STAY ON AND THE STATUS LIGHTS WILL FLASH SLOW GREEN.UPON RECEIVING CONFIRMATION FROM YOUR • SYSTEM, THE CONTROLLER WILL PLAY THE REMOTE MELODY AND SHOW THE REMOTE START ICON.THE CLOCK WILL CHANGE TO 0:00 TO START THE • REMOTE START TIMER. IT WILL TIME HOW LONG THE ENGINE RUNS IN MINUTES & HOURS.(1-WAY TRANSMITTER: PRESS THE “|||” BUTTON TWICE IN 5 SECONDS)If the engine stalls, the system will make up to 3 more attempts.• Each time you park, set the climate controls to give you the desired interior •      temperature when you use the remote start. •  (continued on pg 5)x2*
5Controller & Transmitter Functions (cont’d)CHANNEL 3:  Press and hold the “TRUNK” & “    “ buttons for 3 seconds.YOUR SYSTEM WILL ACTIVATE THE CHANNEL 3 • OUTPUT.UPON RECEIVING CONFIRMATION FROM YOUR • SYSTEM, THE CONTROLLER WILL SHOW THE CHAN-NEL 3 ICON.(1-WAY TRANSMITTER: PRESS AND HOLD THE “||” & “|||” BUTTONS FOR 3 SECONDS)CHANNEL 4:  Press and hold the “LOCK” & “TRUNK” buttons for 3 seconds.YOUR SYSTEM WILL ACTIVATE THE CHANNEL 4 • OUTPUT.THERE IS NO 2-WAY CONFIRMATION FOR THIS • FUNCTION.(1-WAY TRANSMITTER: PRESS AND HOLD THE LOCK & “||” BUTTONS FOR 3 SECONDS)The engine will run for the preset run time (see user feature #17). Run Time Extender•  : Press the “     ” button one time during remote start to restart the engine run timer. The timer will restart at “0:00”.NOTE: This can only be used once per remote start cycle. The controller will also give you “run time expiration” warning (2 chirps) 1 minute before the remote start cycle ends.If you decide not to drive your vehicle, you can turn off the remote start using • the same method to turn it on (Default = press “     ” twice in 5 seconds) NOTE: If user feature #17 is programmed for 1 press, the 1st press = Run Time Extender so an additional press is required.Upon entering the vehicle during remote start mode, turn the ignition key to • the “ON/RUN” position (NOT START!!). When you press the brake pedal, the remote start will turn off allowing the ignition key to take over.seconds.***CHANNEL 5:  Press and hold the “UNLOCK” & “   “ buttons for 3 secondsYOUR SYSTEM WILL ACTIVATE THE CHANNEL 5 • OUTPUT.THERE IS NO 2-WAY CONFIRMATION FOR THIS • FUNCTION.(1-WAY TRANSMITTER: PRESS AND HOLD THE UN-LOCK & “|||” BUTTONS FOR 3 SECONDS)*
6Controller & Transmitter Functions (cont’d)PANIC:  Press and hold the “LOCK” or “UNLOCK” button for 3  seconds.THE SIREN/HORN WILL SOUND, THE PARKING • LIGHTS WILL FLASH, AND THE DOORS WILL LOCK OR UNLOCK DEPENDING WHICH BUTTON IS PRESSED.(1-WAY TRANSMITTER: PRESS AND HOLD THE LOCK OR UNLOCK BUTTON FOR 3 SECONDS)ORSILENT ARM / DISARM:  Press and release the “TRUNK” button twice in 5 seconds.THE PARKING LIGHTS WILL FLASH, AND THE • DOORS WILL LOCK/ARM OR UNLOCK/DISARM DE-PENDING ON THE CURRENT SYSTEM STATUS.UPON RECEIVING CONFIRMATION FROM YOUR • SYSTEM, THE CONTROLLER WILL SHOW THE LOCK/ARM OR UNLOCK/DISARM ICON.(1-WAY TRANSMITTER: PRESS RELEASE THE “||” BUT-TON TWICE IN 5 SECONDS)x2SENSOR BYPASS:  Press and release the “TRUNK” button within 5 seconds of locking/arming the alarm system.THE SYSTEM WILL GIVE ONE CHIRP TO INDICATE • THE SENSOR IS BYPASSED.UPON RECEIVING CONFIRMATION FROM YOUR • SYSTEM, THE CONTROLLER WILL ALSO CHIRP ONCE & DISPLAY THE SENSOR ICON.(1-WAY TRANSMITTER: PRESS AND RELEASE THE “||” BUTTON WITHIN 5 SECONDS OF ARMING THE SYSTEM)21LOW VOLTAGE/TEMP AUTO START:  Press and release the “   ” button within 5 seconds of locking/arming the system.THE SYSTEM WILL GIVE ONE CHIRP TO INDICATE • THE LOW VOLT/LOW TEMP(15 DEGREE ONLY) AUTO-START IS ACTIVATED. SEE PAGE 7 FOR MORE INFO.UPON RECEIVING CONFIRMATION, THE CONTROL-• LER WILL CHIRP ONCE AND THE CLOCK WILL READ “RS AUTO” EVERY 5 SECONDS.(1-WAY TRANSMITTER: PRESS AND RELEASE THE “START” BUTTON WITHIN 5 SECONDS OF ARMING THE SYSTEM)21*
7Controller & Transmitter Functions (cont’d)AUXILIARY FUNCTIONS 1-4:  The actual operation of these functions will vary from car to car. They are designed to operate extra vehicle functions like automatic sliding doors or motorized hatches. Aux 1-4 are virtual outputs only available on certain vehicles when this system is integrated with the vehicle’s data network. Consult with your installer to  nd out if any of these functions are available for your vehicle. If so, con rm each operation with the controller and write each function in the blank spaces provided below.-  Auxiliary 1 Function (___________________): To activate this function, press and release the “trunk” and “start” buttons simultaneously). -  Auxiliary 2 Function (___________________): To activate this function, press and release the “lock” and “trunk” buttons simultaneously).-  Auxiliary 3 Function (___________________): To activate this function, press and release the “unlock” and “start” buttons simultaneously).-  Auxiliary 4 Function (___________________): To activate this function, press and release the “unlock” and “trunk” buttons simultaneously).LOW BATTERY/LOW TEMP AUTOMATIC STARTINGOther Remote Start FeaturesREMOTE VALET:  Press and release the “   ” button within 5 sec-onds of unlocking/disarming the alarm system.THE SYSTEM WILL ENTER ALARM VALET MODE.• SEE PAGE 10 FOR MORE INFO ON VALET MODES.(1-WAY TRANSMITTER: PRESS AND RELEASE THE “START” BUTTON WITHIN 5 SECONDS OF DISARMING THE SYSTEM)12*  This feature will automatically start the engine if the vehicle battery drops below 11 volts or the interior temperature drop to 15 (or 32) degrees fahrenheit. You must acti-vate these features each time you park your car to use them. They can be activated one of two ways:Method 1 - Valet Switch•  Turn the ignition switch “on”, then “off” (engine not running), and within 7 seconds press the valet switch twice.  If there is a 2 second delay without additional valet but-ton presses, the horn will honk 3 times activating low voltage start mode. •  To activate low temp starting, enter low voltage start mode as described above but, before the horn honks, press the valet switch 1 time (15 degrees) or 2 times (32 degrees) within 5 seconds. The horn will honk to con rm your selection.Method 2 - With The Controller (Low Volt + Low Temp - 15 Degrees Only)•  Within 5 seconds of pressing LOCK, press the START button. You will get one chirp and the 2-way controller will alternate between “ARM” and “RS AUTO”. NOTE: When low temp start mode is activated, low voltage start is also activated. These features will operate once every two hours until the ignition key is turned “ON”.
8Other Remote Start Features (cont’d) It is typically recommended that vehicles equipped with turbocharged engines allow the engine to idle after driving to cool the turbocharger. When this Installer Program-mable Feature #4 is enabled, the system will automatically keep the engine running as follows:•  With the engine running, hold the brake pedal and engage the parking  brake.  When the brake pedal is released, the system will keep the engine running for the programmed time (1, 2, or 3 minutes), and then automatically turn it off. •  The system may be locked while the engine is running.  Turbo Timer can be prevented from engaging, or “bypassed” if desired, by turning the engine off before engaging the parking brake, or if it’s already engaged, step on the brake pedal to turn the engine off.TURBO TIMER FEATUREPIT-STOP FEATURE  This feature allows you to leave your engine running for making quick errands. To use this feature, have the engine running normally from the ignition switch and your foot off the brake pedal.  Press the Valet Switch twice; the parking lights will ash and the horn chirps 5 times. Turn the key off and the engine will remain running for the programmed run time.MANUAL TRANSMISSION STARTING  Remote starting with a manual transmission requires a different installation method and installer feature #5 must be turned on. Also, a setup procedure that ensures the transmission was left in neutral must be performed each time you leave your vehicle and intend to use remote start later. Perform these steps:1) With the engine running, hold the brake pedal, apply the parking brake, then release the brake pedal.2) Use the transmitter as if you were activating remote start (default: press START twice). The green status light will start to ash slow.3) Turn off the ignition key and exit the vehicle.4) Press LOCK on the transmitter. The engine will shut down (unless turbo timer is on) and the status light will ash green every 2 seconds to indicate it is ready to be remote started.NOTE: Manual transmission starting is canceled if you enter the vehicle after performing the setup procedure.LAST DOOR ARMING  This system can be congured to arm automatically when all the vehicle’s doors are closed (see user feature #2). When this feature is utilized, the siren/horn will chirp once when all of the doors are closed. At that point, it will start a 30 second count-down (indicated by a fast ashing status light). After 30 seconds, the system will arm (and lock the doors if congured to do so). During the 30 second arming delay, if a point of entry is opened, the countdown will pause until all entry points are closed again. Turning ON the ignition key will cancel the last door arming sequence until the key is turned off and the doors are all closed once again.Security System Features
9Security System Features (cont’d)AUTOMATIC REARMING  This automatically rearms  the alarm if the system is disarmed from the remote. (see user feature #3). When disarmed by remote, the system will start a 90 second countdown (fast ashing status light) to arm the system. This is useful if the controller may accidentally disarms the system when it’s kept in a purse or pocket where other items could potentially press the buttons.  ENHANCED AUTO REARM allows you to cancel the countdown by pressing UNLOCK a second time within 5 seconds of the rst press to disarm the alarm.WHEN THE SYSTEM TRIGGERS  If the system were to be compromised while armed, it will trigger sounding the siren/horn and ashing the parking lights for 30 seconds (programmable). At this point you will also be notied on the controller as to which zone is violated (if in range of the system). When disarming the system after a trigger event, the siren/horn will chirp 4 times and the parking lights will ash 4 times instead of the standard 2 times.LOCK ON TRIGGER: If a door is opened when the system is triggered, it will wait until the door is closed again, then lock the doors. This patented feature is useful to further deny a thief of further access to the vehicle.STORM SAFE MODE: When the system is triggered, pressing the “UNLOCK” button will stop the alarm from sounding but will leave the doors locked. This function is use-ful if you have a false triggering situation due to violent weather.ZONE VIOLATION RECALL: The system is capable of telling you which zones were triggered last. The system’s status light will ash to indicate which zone was triggered. This occurs during the alarm cycle AND after disarming. The system will store the last triggered zone until the vehicle’s ignition key is turned on. See “The Status Light” sec-tion of this manual for further explanation of this feature.NUISANCE PREVENTION: If the system prewarns 5 times within 15 minutes, it will bypass the zone for the remainder of the 15 minutes before rearming the pre-warn zone. Additionally, if a full trigger zone is left open, the system will trigger a total of 3 times before bypassing the zone. Once the zone is closed again, it will re-arm that zone.PRE-WARN DETECTION  This system’s impact sensor is designed, in addition to detecting a full impact, will warn away potential violators when it detects a light impact to the vehicle. The system will respond by chirping the siren/horn 3 times and locking the doors. This is very use-ful when an intruder attempts to unlock the door with “slim jim” types of devices.Using The Valet SwitchEMERGENCY OVERRIDE  If you were to lose or break your controller, you’d need to perform an emergency override to disarm the system and use your vehicle. To do so, use the following steps:STEP 1 - Enter the vehicle (the alarm should sound)STEP 2 - Turn the ignition key to the “ON” positionSTEP 3 - Press the valet switch (located in the window-mount antenna) once   NOTE: Enter your SecureCode at this time if programmed via user feature #1STEP 4 - Turn the ignition “OFF”.
10Using The Valet Switch (cont’d)VALET MODES ALARM VALET MODE, while active, completely disables all security functions. Keyless entry and remote start are still operable. To enter valet mode, perform the following steps:STEP 1 -  Disarm the system either with the controller or by performing an emergency override (make sure not to hold the brake pedal).STEP 2 -  Press and hold the valet switch (located in the window-mount antenna) for 2 seconds. The system will chirp once and the RED status light will turn on. The controller will reect that the system is in alarm valet mode. REMOTE START VALET MODE, while active, disables remote start. Keyless entry and alarm functions are still operable. To enter remote start valet mode, perform the following steps:STEP 1 -  Disarm the system either with the controller or by performing an emergency override and hold the brake pedal.STEP 2 -  Press and hold the valet switch (located in the window-mount antenna) for 2 seconds. The system will chirp once and the GREEN status light will turn on. The controller will not reect remote start valet mode. FULL VALET MODE combines both alarm & remote start valet modes. To acti-vated full valet mode, follow these steps:STEP 1 - Enter remote start valet. You will hear a chirp.STEP 2 - Release the brake pedal but continue holding the valet switch.  After 2 sec-onds, you will hear a second chirp. STEP 3 - Immediately release the valet switch. The status light will alternate between RED and GREEN every second. EXITING VALET MODES is as simple as just pressing and releasing the valet switch once. The status light will turn off. This procedure is the same for all forms of valet mode.SECURECODE  SecureCode allows you to customize the number of valet presses required to per-form an emergency override. This is an extra layer of security that prevents anyone from overriding the alarm even if they have a key to the vehicle. SecureCode has 2 stages with the rst requiring 1-9 button valet presses and the second requiring 0-9 valet button presses. This gives you 99 possible combinations. To program a custom SecureCode, please refer to user feature #1. To perform an emergency override with SecureCode, use the following steps:STEP 1 - With the system armed, enter the vehicle (the alarm will activate).STEP 2 - Turn the ignition switch to the “ON” position.STEP 3 - Within 5 seconds of step 2, press the valet switch to enter the rst digit of your programmed code.STEP 4 - After a few seconds, the siren will stop sounding and chirp once (conrming stage 1). The siren will then continue sounding.STEP 5 - Now, within 5 seconds of step 4, press the valet switch to enter the second digit of your code. If the code is correct, the alarm will disarm.  If the code is entered incorrectly, you must turn the ignition key OFF, then back ON to try again. Additionally, if 2 failed attempts are made, the alarm will ignore any       further attempts for 2 minutes.
11The Status Light  The status lights, located in the window-mount antenna, provide a visual indication of the system’s status via GREEN (remote start status) and RED (alarm status) lights.SECURITY SYSTEM STATUS (RED LIGHT):OFF: The alarm is disarmed and not performing any automatic functions.ON CONSTANT: The alarm is in valet mode.FLASHING SLOW: The alarm is armed and monitoring all entry points.FLASHING FAST: One of the automatic arming features is in progress.AUTOMATIC TRANSMITTER VERIFICATION (RED LIGHT):Every time you turn on the ignition key, the status light will ash a number of times equal to the number of controllers/transmitters programmed to the system. This unique security feature protects you from a potential thief (valet attendant, mechanic, installer, etc.) from adding their own transmitter without your knowledge and access-ing your vehicle and it’s contents at a later time (the perfect crime!).ZONE VIOLATION RECALL:  If the security system is triggered, upon disarming, the RED status lights will ash a number of times to indicate exactly which zone(s), has been violated. It will store the last 2 violated circuits and continually repeat the ash pattern until the system is disarmed and the vehicle’s ignition key is turned ON. 2 FLASHES: Hood trigger3 FLASHES: Door trigger4 FLASHES: Sensor port triggerREMOTE START STATUS (GREEN LIGHT):OFF: The remote start is off and in standby mode.ON CONSTANT: The remote start is in valet mode.FLASHING SLOW: The engine was started successfully and is running.FLASHING FAST: The remote start sequence has begun and is in process of starting the vehicle’s engine.REMOTE START DIAGNOSTICS (GREEN LIGHT):  The remote start system can also indicate which zone caused the last remote start cycle was ended. To see this indicator, place the system into alarm valet mode. Immediately after the chirp, the GREEN status light will ash to indicate what caused remote start to end.1 FLASH: Run time expired.2 FLASHES: Brake pedal was pressed.3 FLASHES: Engine stalled or a bad tach signal.4 FLASHES: Received transmitter command to stop.5 FLASHES: Gear selector was moved from park(or the parking brake was released).6 FLASHES: The alarm was triggered or low battery voltage.COMBINATION INDICATIONS:  This indication reect combinations of functions involving the security system AND remote start.SLOWLY ALTERNATES GREEN/RED: System is in full valet mode.
12The Status Light (cont’d)SOLID GREEN W/ RED FLASH: System is in remote start valet w/ the alarm armed.SOLID RED W/ GREEN FLASH: System is in alarm valet w/ remote start activated.FAST ALTERNATES GREEN/RED: Alarm armed w/ remote start activated.SLOW FLASHING GREEN W/ 1-4 RED FLASHES: Zone violation recall during remote start mode.SLOW FLASHING RED W/ 1 GREEN FLASH: System is armed and ready to remote start in manual transmission mode.  The controller can operate up to 2 different systems. When controlling 2 systems, it will receive all status updates on the currently selected vehicle prole and will receive only trigger alerts for the 2nd vehicle. You can switch from one car to the other at anytime. Use the following steps to change vehicles. SELECTING CAR #1 OR CAR #2Vehicle #1: Press the “P” and “LOCK” buttons for 1 second to select Car #1. The controller will beep/vibrate once and the clock will change to “CAR 1”.Vehicle #2: Press the “P” and “UNLOCK” buttons for 1 second to select Car #2. The controller will beep/vibrate twice and the clock will change to “CAR 2”.Multi-Car OperationController OptionsLCD SCREEN ICONSBattery LevelMelody/VibrateValet ModeHoodTriggerCarjack ModeAlarm StatusRemote StartShutdownClockDoor TriggerIn RangeIndicatorSensorTrigger  All primary commands sent to the system have a conrmation response that is sent to the controller to indicate that the command was successful. If the command is successful, the icon will not display the “X” in the middle of the icon. If no response is received within a few seconds, the “X” will be displayed indicating that you may be out of range of your system. IN-RANGE INDICATOR
131) Press the “P” button for 5 seconds to access the controller features. The controller will beep twice.2) Press and release the “P“ button once to select the clock (hour digits will ash).3) Press the “TRUNK“ button to scroll up or the “     “ button to scroll down. 4) Press the “P” button to switch to the minute digits.5) Press the “TRUNK“ button to scroll up or the “     “ button to scroll down.6) Wait 10 seconds or press the “P” button for 5 seconds to exit programming. The controller will beep once.SETTING THE CLOCK  The controller has 5 different melodies to choose from for remote start ON and 5 melodies for remote start OFF conrmation.1) Press the “P” button for 5 seconds to access the controller features. The controller will beep twice.2) Press and release the “P“ button 3 times to select the melody settings. The clock will change to “01 STRT” indicating “start melody #1” for the remote start ON melody.3) Press the “TRUNK“ button or the “     “ button to scroll through the melodies. 4) Press the “P” button to switch to the remote start OFF melody selection.5) Press the TRUNK button or the “     “ button to scroll through the melodies.6) Wait 10 seconds or press the “P” button for 5 seconds to exit programming. The controller will beep once.CHANGING REMOTE START MELODIESController Options (cont’d)SELECTING MELODY & VIBRATE MODES  Whenever 2-way alerts are received from the system, the controller can alert you with a melody, vibration, or both. By default, the controller is set for melody only. Press the “P” and “TRUNK“ buttons simultaneously for 1 second to change the setting.  The controller has 2 convenient timer functions. The PARKING TIMER tells you how long you’ve been parked in case you are at a parking meter or other parking areas with time restrictions. The REMOTE START TIMER tells you how long your engine has been running in remote start mode. PARKING TIMER: Press LOCK twice within 5 seconds. When the controller receives both LOCK conrmations, it will start the timer.REMOTE START TIMER: This turns on every time you remote start.Note: Pressing the “P” during either timer will switch to the clock.PARKING TIMER & REMOTE START TIMER**** You can lock the buttons on the controller to prevent accidental button presses. To lock the buttons, press “P” and “    “ simultaneously for 1 second. Repeat this to unlock the buttons.BUTTON LOCK* This feature turns off the screen after 15 seconds of no activity to save battery life.1) Press the “P” button for 5 seconds to access features. The controller beeps twice.2) Press the “P“ button 5 times to select “Power Save” (clock reads “PS ON”).3) Press the “TRUNK“ button to change between “PS ON” or “PS OFF”. 4) Wait 10 seconds or press the “P” button for 5 sec. to exit programming. POWER SAVE MODE
14Anti-Carjacking Protection  The system is equipped with two separate Anti-Carjacking protection features (igni-tion, open door, or both).  All are programmable, and must be turned on to operate.  Once activated, the user has 53 seconds to cancel the Anti-Carjacking protection process (described below).  If Anti-Carjacking is not cancelled, 53 seconds after being activated the siren will begin to chirp for 7 seconds to alert the user that the system is about to enter into an alarm condition.  The Valet Switch may still be pressed once during this period to cancel the Anti-Carjacking process.  If the Anti-Carjacking process is not cancelled before the 60 second countdown expires, the system will enter an alarm condition, sounding the siren and ashing the parking lights.   30 seconds after this occurs, or should the ignition be turned off in the meantime, the stater interrupt will engage. Once the system enters the alarm condi-tion, it will not respond to the transmitter, nor will the system reset automatically after 60 seconds, and it can only be disengaged by:Step 1  Turning the vehicle’s ignition off.Step 2  Turning the ignition back on.Step 3  Within 5 seconds, perform an Emergency Override using the Valet Switch.  If the SecureCode has been customized, the correct number of Valet Switch presses must be made.  The different types of Anti-Carjacking protection are:Ignition Activated Anti-Carjacking activates every time the vehicle’s ignition is turned on.  The Valet Switch must be pressed within 60 seconds of activating to can-cel Anti-Carjacking. This is User Programmable Feature #15.Door Anti-Carjacking activates when a door is opened after the vehicle is started and the engine is running.  The Valet Switch must be pressed within 60 seconds after activation to cancel Anti-Carjacking. This is User Programmable Feature #15.
15If the Unauthorized Transmitter Alert feature is on, programming a transmitter to the system will activate the “UTA” warning and the extended Status Light indication. For the next 48 hours, the siren/horn will sound a brief series of chirps every time the vehicle’s ignition key is turned on.   Special Programming procedure to turn on the UTA feature:  Using this method to program transmitters or optional controllers, and to turn on the Unauthorized Trans-mitter Alert feature.  Follow the same steps as the Standard Programming, but on any transmitter/con-troller being programmed instead of pressing  the “lock” button, press the “lock” and the “unlock” buttons together.   This action turns on the Unauthorized Transmitter Alert feature and at the same time programs the transmitter or controller to operate the system.  Once the Unauthorized Transmitter Alert feature is turned on, the warning will sound for 48 hours after any transmitter programming, including the programming session which was used to turn it on. This feature can only be turned off again by sending the system back to Omega for a reset.Step 1  Turn the ignition key “ON”, then “OFF”Step 2  Within 5 seconds of step 1, press the valet switch 5 times to access user features (10 times to access installer features).  ~ The siren/horn will sound and the status light will turn on.Step 3  Within 10 seconds of step 2, press the valet switch the number of times cor-responding with the desired feature’s number.  ~ The siren/horn will chirp, the status lights, and the parking lights will ash equal   to the selected feature.Step 4  Change the feature by pressing the transmitter button that corresponds with the desired setting. The siren/horn will chirp to correspond with the chosen setting.Programming FeaturesStandard Programming:  Using this method to program additional or replace-ment transmitters does not turn on or otherwise affect the Unauthorized Transmitter Alert (UTA) feature. Before you begin, have all transmitters which are to operate the system at hand and make sure the correct vehicle prole (see page 12) is selected on the controller(s). Step 1 Then, turn the ignition “on”.Step 2 Within 5 seconds of Step 1, press the Valet Switch 5 times. The siren/horn will briey sound, conrming that the system is ready to learn a transmitter code. Step 3 Press the “lock” button on each transmitter one at a time. The system will chirp the siren/horn once to conrm that each was learned. If a code is not received within  10 seconds of Step 2, the learning process will automatically exit. Programming Controllers/Transmitters
16User Programmable FeaturesTo custom program a new SecureCode:  Step 1 Follow Steps 1 to 4 in the previous “Programming Features” section to access “feature #1”. Step 2 Within 10 seconds slowly press and release the controller or transmitter’s “arm/lock” button the number of times equal to the desired SecureCode for stage 1, allow the system to respond to each controller/transmitter button press with a siren chirp before pressing the button again. A few seconds after the nal button press, the system will chirp the horn/siren conrming the total number for stage 1.Step 3 Congure stage 2 of the SecureCode by pressing and releasing the “disarm/unlock” button the number of times desired for the stage 2.  The system will conrm as it did for stage 1.Feature #2 - Last Door Arming Off                   (press “lock” button to program) - DEFAULTOn w/o Doors Locking  (press “unlock” button to program)On w/ Doors Locking   (press “trunk” button to program)“Last Door Arming” has the system automatically arm itself every time you exit the vehicle (the complete operation is described on page 8).  This feature turns that op-eration on or off, and with options of having Last Door Arming operate with or without also locking the doors when the system does arm.Feature #1 - SecureCodeDEFAULT - 1 PressSecureCode is a unique patented feature which allows you to custom select the num-ber of Valet Switch presses in two stages, instead of a single “1 press”, which would be required in order to perform an Emergency Override. If any of the three anti-car-jacking features are utilized, a customized SecureCode would also be required to turn it off once it is fully activated. The SecureCode operation is described on page 10.Feature #4 - Starter Interrupt Functions     Alarm Only         (press “lock” button to program) - DEFAULTAnti-Grind Only      (press “unlock” button to program)Alarm & Anti-Grind  (press “trunk” button to program)Automatic          (press “start” button to program)Alarm Only - The Starter Interrupt is operable whenever the alarm is armed.  Anti-Grind Only -  The Starter Interrupt is operable whenever remote start is on. Alarm & Anti-Grind - This setting engages starter interrupt when the alarm is armed AND when the system is in remote start mode. This prevents the starter from grinding  if the user accidentally turns the key to “START” during remote start. Automatic - This will cause the Starter Interrupt output to automatically engage 90       seconds after the ignition switch is turned “off”, and after disarming.  Feature #3 - Automatic RearmingOff                  (press “lock” button to program) - DEFAULTOn w/o doors locking  (press “unlock” button to program)On w/ doors locking    (press “trunk” button to program)Enhanced auto rearm  (press “start” button to program)“Automatic Rearming”, described on page 7, rearms the alarm if accidentally dis-armed.  Options are to have Automatic Rearming operate with or without also locking the doors when the system does rearm. Enhanced auto rearm allows you to cancel the rearming sequence by pressing unlock a 2nd time after disarming.
17User Programmable Features (cont’d)Feature #5 - Ignition Activated Override Off      (press “unlock” button to program) - DEFAULTOn      (press “lock” button to program)This feature allows an activated system to be overridden and disarmed by simply turning the ignition switch on within 10 seconds of the system’s activation.  After 10 seconds, the Emergency Override must be performed.Feature #7 - Open Door Bypass of Ignition LockingOn      (press “arm/lock” button to program) - DEFAULTOff      (press “disarm/unlock” button to program)This feature cancels the automatic locking or unlocking of the vehicle’s doors if one of the doors is open when the ignition switch is turned on or off. Feature #6 - Ignition Controlled Lock/UnlockOff             (press “lock” button to program) - DEFAULT Lock w/ Ignition On            (press “unlock” button  to program)Unlock w/ Ignition Off          (press “trunk” button  to program)Lock And Unlock w/ Ignition     (press “start” button  to program)This feature controls the lock/unlock operations when the ignition key is turned on/off, Feature #8 - Conrmation Chirps            On           (press “lock” button to program) - DEFAULTExcept Valet Mode          (press “unlock” button to program)On Demand               (press “trunk” button  to program)Off           (press “start” button  to program)This feature removes the system’s arming and disarming conrmation chirps for particular functions. The “On Demand” setting allows you to lock and unlock the doors without chirps. Similar to OEM keyless entry, pressing either function a 2nd time, will produce conrmation chirps.Feature #9 - Conrmation Chirp Volume   Medium High        (press “trunk” button  to program) - DEFAULTLow   (softest)      (press “lock” button to program)Medium Low         (press “unlock” button  to program)High   (loudest)    (press “start” button  to program)This feature allows the choice of four different volume levels of the system’s conrma-tion chirps, and when programming it, the buttons can be repeatedly and sequen-tially pressed, thus making it easy to hear and choose the setting with the best chirp volume.   Feature #10 - Alarm Duration30 Seconds   (press “lock” button to program) - DEFAULT60 Seconds   (press “unlock” button  to program) 90 Seconds     (press “trunk” button to program)120 Seconds  (press “start” button  to program)      This feature allows four choices of the Alarm Duration, which is the period of time for which the system sounding the siren (and/or horn, optionally) and ashes the parking lights when it is triggered.  Caution: Before lengthening the Alarm Duration you should always check and determine if there are any local anti-noise or nuisance ordinances in your area, to avoid the possibility of receiving a violation citation.
18User Programmable Features (cont’d)Feature #11 - Flashing Light ConrmationsOn w/ Disarm, Flash w/ RS      (press “unlock” button to program) - DEFAULTOn w/ Disarm & Remote Start    (press “lock” button to program) On During Remote Start        (press “trunk” button to program)Flashing During Remote Start    (press “start” button to program)This feature affects the parking light conrmations for system disarm & remote start functions.  With the above options, you can select any combination of:- Flashes twice after disarm- Flashes twice then stays on for 30 seconds after disarm- Stays on during remote start mode- Flashes slowly during remote start modeFeature #12 - 2nd Channel (Trunk Release) Also Disarms SystemOn      (press “lock” button to program) - DEFAULTOff      (press “unlock” button to program) “2nd channel” is most commonly used for trunk release, in which case the alarm should also disarm.  This feature, turned on, congures the system to disarm when the 2nd channel is used.Feature #13 - Arming Delay3 Seconds       (press “lock” button to program) - DEFAULT15 Seconds   (press “unlock” button  to program) 30 Seconds   (press “trunk” button to program)45 Seconds   (press “start” button  to program) This determines how long the alarm waits to monitor trigger inputs after arming the system. Longer durations allow some vehicle systems to “settle” before monitoring to prevent false trigger conditions.     Feature #14 - Alarm Functions Bypass Off      (press “unlock” button to program) - DEFAULTOn      (press “lock” button to program)  This feature converts the system into a strictly Keyless Entry/Remote Start System by eliminating all antitheft alarm-oriented operations and features.  Feature #15 - Anti-CarjackingOff               (press “start” button to program) - DEFAULTIgnition Only    (press “lock” button to program) Door Only      (press “unlock” button to program)Ignition + Door   (press “trunk” button  to program) This selects between the 2 forms of anti-carjacking protection.  Details on using anti-carjacking protection are described on page 14.Feature #16 - Open Door Warning Upon ArmingOff      (press “unlock” button to program) - DEFAULTOn      (press “lock” button to program)When this feature is turned on, if one of the vehicle’s doors is open at the time that the system is armed via the controller or transmitter, the siren  will chirp 3 times and the parking lights will ash 3 times instead of once.
19User Programmable Features (cont’d)Feature #17 - Remote Start ActivationPress “start” button 2 times    (press “lock” button to program) - DEFAULTPress “start” button 1 time    (press “unlock” button  to program) Press Lock & Unlock         (press “trunk” button to program)This feature changes how the remote start feature is activated using the controller or transmitter. It also affects how many pulses activate remote start from the WHITE/BLUE activation input wire.Feature #18 - Remote Start Run Time10 Minutes    (press “disarm/unlock” button to program) - DEFAULT5 Minutes    (press “arm/lock” button to program) 15 Minutes    (press “trunk” button to program)20 Minutes    (press “start” to program)This feature sets the period of time that the engine will run when remote started. If the engine is not stopped by controller/transmitter command or a safety circuit violation, the engine will automatically stop upon the expiration of the selected time period.Installer Programmable FeaturesFeature #2 - Light Relay Functions     Dome Light Output  (press “lock” button to program) - DEFAULTDoor Lock         (press “unlock” button to program)Ignition Output      (press “trunk” button to program)Accessory Output   (press “start” button to program)The system has two built-in relays, which can be programmed to perform several different func-tions.  The primary function of this relay, is to operate the vehicle’s dome, or interior lighting as part of the system’s operations.  Optionally, if desired or needed, this relay can be programmed to be a door lock relay, or as medium-capacity ignition or accessory outputs (10A max), if needed for remote starting use. Feature #1 - Doorlocking Functions     0.8 Second Outputs        (press “lock” button to program) - DEFAULT3 Second Outputs          (press “unlock” button to program)Double Pulse Unlock Output  (press “trunk” button to program)Total Closure Lock Output   (press “start” button to program)This single feature gives the installer several needed options, to match the system’s doorlocking outputs to suite different vehicle requirements. The total closure setting provides a 28 second lock pulse and a 0.8 second unlock pulse.This group of Installer Programmable Features are all accessed as a group in the second level of features’ programming.  These features have a direct affect upon the system’s operations related to the installation and vehicle type AND SHOULD ONLY BE CHANGED BY THE INSTALLER!!!
20Feature #6 - Engine Detection MethodTachless Hi  (press “lock” button to program) - DEFAULTTachless Lo  (press “unlock” button to program)Tach Wire        (press “trunk” button to program)Data Tach        (press “start” button to program) Crank Only  (press “lock” & “unlock” to program)This feature selects the method in which the remote start monitors the engine’s running condition in remote start mode.  “Tachless Hi” sensitivity mode uses a preset crank time (see installer feature #7) and monitors the vehicle’s voltage level to determine if the engine is running. This setting looks for a voltage increase of 0.3v after cranking.  “Tachless Lo” sensitivity mode operates like the “Tachless Hi” setting but looks for a voltage increase of 0.5v after cranking.“Tach Wire” Before this setting is programmed, refer to the “Violet/White wire” section of the installation manual for proper wiring connection and the Tach Learn Procedure. It will crank the engine for up to 3 seconds or until a tach signal is detected.“Data Tach” mode operates just like the “Tach Wire” setting except it takes its reading from the D2D data port instead of using the Violet/White wire. Before using, make sure this function is sup-ported by the Databus Interface module. “Crank Only” AKA “blind start” is similar to the “Tachless” settings however, it only makes one start attempt and does not monitor engine running conditions. This is useful for many “push-to-start” vehicles.Feature #5 - Manual Transmission ModeOff      (press “unlock” button to program) - DEFAULTOn      (press “lock” button to program)This feature changes the parameters of the system’s remote start operation to be suitable for manual transmission-equipped vehicles via a “setup” procedure which must be followed upon exit-ing the vehicle to ensure the transmission is in neutral.Feature #4 - Turbo TimerOff          (press “lock” button to program) - DEFAULTRun 1 Minute   (press “unlock” button to program)Run 2 Minutes  (press “trunk” button to program)Run 3 Minutes  (press “start” button to program)This feature, the operation of which is described on page 9, when turned on congures the system to automatically keep the engine running briey after it is turned off.  This operation is designed specically for vehicles having turbocharged engines (the user may tempo-rarily bypass the feature if desired). This feature should only be programmed by the installer, and the operation of this feature depends on the correct connection of the safety wire to the vehicle’s parking brake.   Feature #3 - Horn Relay FunctionsHorn Output        (press “lock” button to program) - DEFAULTDoor Unlock        (press “unlock” button to program)Trunk Release      (press “trunk” button to program)Pulse After Start    (press “start” button to program)The primary function of this second relay, is to operate the vehicle’s existing horn; either in conjunction with the electronic siren, or in place of the siren.  Using both the siren and the horn creates an extremely effective security system. Optionally, if desired or needed, this relay can be programmed as a door unlock, trunk release, or pulse after start relay.Installer Programmable Features (cont’d)
21Installer Programmable Features (cont’d)Feature #8 - PINK/WHITE (IGN #2)Wire FunctionIgnition   (press “lock” button to program) - DEFAULTAccessory (press “unlock” button to program)Starter    (press “trunk” button to program)This feature changes the operation of the unit’s large PINK/WHITE output wire. This feature should only be programmed by the installer. Feature #7 - Starter Cranking Time0.75 Second  (press “lock” button to program) - DEFAULT1.00 Second  (press “unlock” button to program)1.5 Seconds  (press “trunk” button to program)2.25 Seconds  (press “start” button to program)This feature determines the crank time of the 1st start attempt when in “Tachless” mode. If the engine doesn’t start on the rst attempt, it will retry up to 3 more times extending the crank time by an additional 0.2 second with each attempt..Feature #9 - Arm, Disarm or Additional ChannelsArm / Disarm         (press “lock” button to program) - DEFAULTArm / Channel 5       (press “unlock” button to program)Channel 4 / Disarm    (press “trunk” button to program)Channel 4 / Channel 5  (press “start” button to program)The system has outputs designed for arming and/or disarming a factory-equipped security system.  These wires may be used instead to provide further system outputs, which are remotely operated by the controller or transmitter.  These outputs are in addition to the 2nd channel and 3rd channel outputs. As shown in the programming assignment, the arm, disarm, channel 4 and channel 5 are programmable as various combinations.  For example, if the disarm output is needed, but not the arm output, then channel 4 may be made available for use. Feature #11   Remote Start Lock ControlOff            (press “lock” button to program) - DEFAULTLock After Start       (press “unlock” button to program)Unlock before start      (press “trunk” button to program)Unlock Before+Lock After Start  (press “start” button to program)This feature allows for OEM alarm/lock control in relation to remote start operations thus eliminat-ing extra wiring.Feature #10   Gasoline Or Diesel EngineGasoline      (press “lock” button to program) - DEFAULTDiesel 15 Sec. Delay  (press “unlock” button to program)Diesel 20 Sec. Delay  (press “trunk” button to program)Diesel 30 Sec. Delay  (press “start” button to program)This feature changes the system’s timing of the ignition and starter output sequence for gas or diesel engines. Gasoline: the starter output will occur 3 seconds after the ignitions turn on. When in “Tachless” mode, the engine running status is determined 10 seconds after starting. Diesel: the starter output will occur 15, 20, or 30 seconds after the ignitions turn on (allows for glow plug warming). When in “Tachless” mode, the engine running status will be determined 40 seconds after cranking.
22Installer Programmable Features (cont’d)This device complies with FCC Rules part 15. Operation is subject to the following two conditions, (1) This device may not cause harmful interference and, (2) This device must accept any interference that may be received, including interference that may cause undesired operation.The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this equipment. Such modications could void the user’s authority to operate the equipment.Feature #12   Low Temp Crank Extender0ms (Off)  (press “lock” button to program)200ms  (press “unlock” button to program) - DEFAULT300ms  (press “trunk” button to program)400ms  (press “start” button to program)When the vehicle’s interior temperature is below freezing, this feature adds extra crank time to the base timing (see  installer feature #7). It applies to tachless modes only (installer feature #6)Feature #13   Data Port ProtocolADS (iData)  (press “unlock” button to program) D2D (Trilogix)  (press “lock” button to program) - DEFAULTThis feature determines which data protocol is used on both data ports. Choose this based on the accessory being connected to the port. NOTE: When a BLADE is inserted, this feature automatically switches to the ADS protocol.Feature #14   Lock On PrewarnOn  (press “lock” button to program)  - DEFAULTOff  (press “unlock” button to program)By default, if the prewarn zone is triggered, the system will automatically lock the doors to combat unauthorized entry from lock picking. If this causes conict with OEM vehicle functions, you can turn it off.Feature #15   Blue Satellite Port, Blue Wire FunctionStatus        (press “lock” button to program) - DEFAULTPulse Before Start    (press “unlock” button to program)Defrost Pulse      (press “trunk” button to program)Pulse After Engine Off  (press “start” button to program)This determines the function of the Blue wire on the Blue satellite relay port.The Status setting turns on briey before the Ignition output and stays on during remote start mode. The other settings give a 0.8 second pulse under the selected condition. Defrost Pulse will send a pulse after start only when the cabin temperature is below freezing (32 degrees F)Feature #16   Low Current / Motorcycle ModeOn  (press “lock” button to program)  Off  (press “unlock” button to program) - DEFAULTThis feature, when on, reduces the system’s current draw by as much as 40% to maximize the vehicle’s battery life while the alarm is armed. It causes the starter interrupt output to only oper-ate when the ignition is turned on and reduces the frequency of the “armed” ashing status light signicantly. This is ideal when the system is to be used on vehicles that have limited battery capacity and/or may sit for extended periods without charging the battery.
23Programmable Features MatrixUser Feature Programming: Ignition on, off, press valet 5 times# Feature Lock Button Unlock button Trunk button  ”START” button1   Secure Code 1, 0 (default)2   Last Door Arming Off On w/o lock On w/ Lock3   Automatic Rearming Off On w/o lock On w/ Lock Enhanced Rearm4   Starter Interrupt Functions Alarm Anti-Grind Only Alarm+Anti-Grind Automatic5   Ignition Override On Off6   Ignition Lock/Unlock Off Lock w/ IGN ON Unlock w/ IGN Off Lock + Unlock w/ IGN On/Off7   Open Door Bypass For Ign. Locks On Off8   Conrmation Chirps On Except Valet mode On Demand Off9  Chirp Volume Low Med Low Med Loud Loud10  Alarm Cycle 30 sec 60 90 12011  Flashing Lights Conrmation On w/ Disarm + RS SteadyOn  w/  Disarm  + RS Flashing Steady During RS Flashing  During RS12  Disarm Upon Trunk Release On Off13  Arming Delay 3 sec 15 30 4514  Alarm Functions Bypass On Off15  Anti-carjack Ignition Only Door Only Ignition + Door Off16  Open Door Warning Upon Arm On Off17  Remote Start Activation Start / Pulse x 2 Start / Pulse x 1 Lock+Unlock18  Remote Start Run Time 5 min 10 min 15 min  20 minInstaller Feature Programming: Ignition on, off, press valet 10 times1  Doorlock pulse 0.8 sec 3 sec Double unlock Total closure2  Light Relay Functions Dome light Lock Ignition Acc3  Horn Relay Functions Horn Unlock Trunk Release Pulse after Start4  Turbo Timer Off 1 min 2 min 3 min5  Manual Transmission On Off6  Engine detection Tachless Hi Tachless Lo Tach Wire DatatachCrank Only (press Lock + Unlock)7  Crank Time 0.7 sec 1 sec 1.5 sec 2.25 sec8  Pink/White Ignition Wire Function Ignition Accessory Start9  Arm/Disarm/Additional Ch. Arm/Disarm Arm/Ch 5 Ch4/Disarm Ch 4/Ch 510  Gas or Diesel Engine Gas Diesel  (15 sec. Delay)Diesel  (20 sec. Delay)Diesel  (30 sec. delay)11  Remote Start Lock control Off Lock after start Unlock before start Both12  Low Temp Crank Extender 0ms 200ms 300ms 400ms13  Data Port Protocol D2D (Trilogix) ADS (iData)14  Lock on prewarn On Off15  Blue Satellite Port Blue Wire Function Status Pulse Before StartPulse After Start Below FreezingPulse After Engine Off16  Low Current/Motorcycle Mode On Off
Back CoverColor cover is in a separate le.

Navigation menu