OKAYO Electronics DGBDUT DigiBee Group Guide System User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3648040
Application ID	G7KwhEMGAornLqKBQFtrTw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	22.02kB (275259 bits)
Date Submitted	2017-11-21 00:00:00
Date Available	2017-11-21 00:00:00
Creation Date	2015-11-24 14:52:24
Producing Software	Corel PDF Engine Version 1.0.0.536
Document Lastmod	0000-00-00 00:00:00
Document Title	DigiBee-DUT_DUR中英文說明書_簡易-(okayo)-12
Document Creator	CorelDRAW 版本 12.0

DigiBee Group Guide System
Transmitter
Receiver
9 10 11
12
External Antenna
Power/Signal indicator
LCD battery status
LCD channel lock
8 Power button
7 Up/Down button
9 Inbuilt microphone
1 External Antenna
7 Up/Down button
2 Power/Signal indicator
8 Power button
3 LCD battery status
9 Earphone socket
10
Mic-in socket
5 LCD selected channel
11
Mute/Sync button
4 LCD channel lock
6 Aux-in socket
12
Lanyard
tie-up
5 LCD selected channel
6 Volume wheel
Setup/Installation
Power on/off
Press and hold power button for 1 sec. to power the
device on. LCD screen shows" "and then last used
channel.
Press and hold power button for 2 sec. to power the
device off. LCD screen shows" " and then shuts down.
Channel lock/unlock
Channel will automatically be locked and symbol " "
shows up if the device is idle for 5 seconds after being
turned on.
To unlock the channel, press buttons and simultaneously
for 2 seconds until symbol " "disappears.
Channel selection
Press button or to select preferred channel when
channels are unlocked.
Power saving (receiver only)
Power of receivers will be off if no signal is received for 20 minutes.
Sensitivity adjustment (transmitter only)
When channel is locked, press and hold for 2 seconds to enter
mode .
Press button and to adjust the sensitivity (default: ,
~ ).
Press power button to confirm the setting.
Power/Signal indicator
Indicator behavior
Red
Flash
Blue
Purple
Red
Steady
Blue
No LED
Transmitter
Receiver
Low battery&
Mute activated
Sufficient battery&
Mute activated
Sync activated
Low battery&
Signal transmitted
Sufficient battery&
Signal transmitted
Low battery&
Signal received
Sufficient battery&
Signal received
Device is not turned on Signal is not received
Channel synchronization
Press mute/sync button on transmitter before it is on.
Turn the transmitter on and purple LED flashes to indicate the activation
of channel-sync mode.
Turn receiver(s) on to be channel synchronized (one or multiple receivers
can be turned on at the same time).
When channel is successfully synchronized, receiver's LCD shows same
channel as that of transmitter's and its LED turns steady blue.
Press mute/sync button of transmitter again to escape from sync setup.
Note
1.To re-activate channel-sync mode, please turn the transmitter off and follow
above steps again.
2.After the transmitter escapes from channel-sync mode, its sound will be
muted when mute/sync button is pressed.
3.If the channel is not successfully synchronized, turn receiver(s) off and then
on again to be re-synchronized.
4.Maximum synchronized range is 1 meter. Out of the limited rage might result
in failed connection.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Notice:
The changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
IMPORTANT NOTE:
To comply with the FCC RF exposure compliance requirements, no change to the antenna or the
device is permitted. Any change to the antenna or the device could result in the device exceeding
the RF exposure requirements and void user’s authority to operate the device.
FCC INFORMATION
The Federal Communication Commission Radio Frequency Interference Statement includes the
following paragraph:
The equipment has been tested and found to comply with the limits for a Class B Digital Device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction,
may cause harmful interference to radio communication.However, there is no grantee that
interference will not occur in a particular installation. If this equipment dose cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on , the user is encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
※ Specifications are subject to change without prior noite.
11/15

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : D:20151124145224
Creation Date--Text             : 
Creator                         : CorelDRAW 版本 12.0
Modify Date                     : 0000:01:01 00:00:00
Mod Date--Text                  : 
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Corel PDF Engine Version 1.0.0.536
Creator Tool                    : CorelDRAW 版本 12.0
Metadata Date                   : 2015:11:24 14:53:28+08:00
Format                          : application/pdf
Title                           : DigiBee-DUT_DUR中英文說明書_簡易-(okayo)-12
Document ID                     : uuid:a2a9a491-c902-40f6-9616-7d88b30302b9
Instance ID                     : uuid:87f6c334-e3fc-4a93-86ba-391fee5b9bdf
Page Count                      : 1

EXIF Metadata provided by EXIF.tools