OMG plc OMGLIFEAP1 Autographer User Manual Bonita Regulatory Information

OMG plc Autographer Bonita Regulatory Information

UserManual.wiki >

OMG plc >

OMGLIFEAP1 User Manual HTML Version

User guide regulatory info

Version 1.3 6AUG13 Page 1 of 9

Autographer Safety and Regulatory Information

The terms “device” or “wireless device” used in this section refer to your Autographer

wearable camera. Read this information before using your device.

Federal Communications Commission (FCC) Part 15 Information to User

Pursuant to part 15.21 of the FCC Rules, you are cautioned that

changes or modifications not expressly approved by OMG plc

could void your authority to operate the device. This device

complies with part 15 of the FCC Rules. Operation is subject to

the two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference

received, including interference that may cause undesired

operation.

Note: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15(c) of the FCC CFR47 rules. These limits

are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency (RF) energy and, if not used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular application. If this equipment does

cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Consult the dealer or an experienced radio/TV technician for help.

FCC Notice and Cautions

The device may cause TV or radio interference if used in close proximity to receiving

equipment. The FCC can require you to stop using the equipment if such interference

cannot be eliminated.

Cautions: Any changes or modifications to your device not expressly approved by

OMG plc could void your warranty for this equipment and void your authority to

operate this equipment. Only use approved batteries. The use of any unauthorized

accessories may be dangerous and void the device warranty if said accessories cause

damage or a defect to the device. Although your device is quite sturdy, it is a

complex piece of equipment and can be broken. Avoid dropping, hitting, bending or

sitting on it.

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. End users must follow the specific operating instructions

for satisfying RF exposure compliance. This transmitter must not be co-located or

operating in conjunction with any other antenna or transmitter.

Version 1.3 6AUG13 Page 2 of 9

For Canadian Customers

Under Industry Canada regulations, this radio transmitter may only operate using an

antenna of a type and maximum (or lesser) gain approved for the transmitter by

Industry Canada.

To reduce potential radio interference to other users, the antenna type and its gain

should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not

more than that necessary for successful communication."

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interference

that may cause undesired operation of the device.

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio

peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur)

approuvé pour l'émetteur par Industrie Canada.

Dans le but de réduire les risques de brouillage radioélectrique à l'intention des

autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la

puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité

nécessaire à l'établissement d'une communication satisfaisante.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux

appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions

suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de

l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est

susceptible d'en compromettre le fonctionnement.

Other Important Safety Information

 Only qualified personnel should service the device. Faulty service may be

dangerous and may invalidate any warranty applicable to the device.

 Do not store or carry flammable liquids, gases, or explosive materials in the

same compartments as the device, its parts, or accessories.

 For vehicles equipped with an air bag, remember that an airbag inflates with

great force. Do not place objects, including portable wireless equipment near

or in the area over the air bag or in the airbag deployment area. If the

wireless device is within the deployment area as an air bag inflates, serious

injury could result.

 Switch off the device off before boarding an aircraft. The use of wireless

devices in aircraft is illegal and may be dangerous to the aircraft’s operation.

Check with appropriate authorities before using any function of the device

while on an aircraft.

 The primary responsibility of every driver is the safe operation of his or her

vehicle. Do not engage in any activity while driving a moving vehicle which

may take your eyes off the road or become absorbed in any activity that your

ability to concentrate on the act of driving becomes impaired.

 Failure to observe these instructions may lead to the suspension or denial of

network services, or legal action, or both.

Version 1.3 6AUG13 Page 3 of 9

Battery Use and Safety

 The battery in this device is not intended to be replaced by the consumer. If

you believe the battery is damaged or needs to be replaced, return the device

for inspection and replacement.

 Do not let the device or battery come in contact with liquids. Liquids can get

into the device’s circuits, leading to corrosion. Even when the device appears

dry and appears to operate normally, the circuit could slowly corrode and

pose a safety hazard.

 Do not place the device in or near a heat source. Excessive heating can

damage the device and battery and could cause the device or the battery to

explode. Do not dry a wet or damp device with an appliance or heat source

such as a microwave oven, hair dryer, iron, or radiator. Avoid leaving your

device in your vehicle in high temperatures.

 Do not dispose of the device or battery in a fire. The device or battery may

explode when overheated.

 Avoid dropping the device. Dropping the device, especially on a hard surface,

can potentially cause damage. If you suspect damage to the device or

battery, return it for inspection.

 Never use any battery that is damaged in any way.

 Warning. Use of a non-OMG plc approved batteries may present a risk of

fire, leakage, or other hazard. OMG plc warranty does not cover damage to

the device caused by non-OMG plc approved batteries.

 Do not use incompatible batteries and chargers. Some websites and second-

hand dealers not associated with reputable manufacturers and carriers, might

be selling incompatible or even counterfeit batteries and chargers. Please

refer to OMG plc for advice. Misuse or use of incompatible batteries and

chargers could result in damage to the device and a possible risk of fire,

explosion, or leakage, leading to serious injuries, damage to your device, or

other serious hazard.

GPS

The device uses a Global Positioning System (GPS) signal for location acquisition. A

GPS uses satellites controlled by the U.S. Government that are subject to changes

implemented in accordance with the Department of Defense policy and the 2008

Federal Radio navigation Plan (FRP). Changes may affect the performance of

location-based technology within your device.

Operating Environment

 Avoid temperature below 0oC/ 32oF or above 45oC/ 113oF.

 Do not expose your device to dust, dirt, or sand.

 Remember to follow any special regulations in force in any area, and always

switch your device off whenever it is forbidden to use it, or when it may cause

interference or danger. When connecting the device or any accessory to

another device, read its user’s guide for detailed safety instructions. Do not

connect incompatible products.

 Implantable Medical Devices. A minimum separation of 6 inches (15.3

mm) should be maintained between the device and an implantable medical

Version 1.3 6AUG13 Page 4 of 9

device, such as a pacemaker or implantable defibrillator, to avoid potential

interference by the device. Persons who have such implantable medical

devices:

o Should ALWAYS keep the device more than 6 inches (15.3 mm) from

their implantable medical device when the device is turned ON;

o Should not carry the device in a breast pocket;

o Should immediately turn the device OFF if there is any reason to

suspect that interference is taking place;

o Should read and follow the directions from the manufacturer of your

implantable medical device. If you have any questions about using

your wireless device with an implantable medical device, consult your

health care provider.

 Other Medical Devices. If you use any other personal medical devices,

consult the manufacturer of your device to determine if it is adequately

shielded from external RF energy. Your physician may be able to assist you in

obtaining this information. Immediately turn the device OFF if there is any

reason to suspect that interference is taking place.

Switch your wireless device off in health care facilities when any regulation

posted in these areas instructs you to do so. Hospitals or health care facilities

may be using equipment that could be sensitive to external RF energy.

 Vehicles. RF signals may affect improperly installed or inadequately shielded

electronic systems in motor vehicles. Check with the manufacturer or its

representative regarding using your wireless device in a motor vehicle. You

should also consult the manufacturer of any equipment that has been added

to your vehicle. Immediately turn the device OFF if there is any reason to

suspect that interference is taking place.

 Posted Facilities. Switch your device off in any facility where posted notices

require you to do so.

 Potentially Explosive Environments. Switch your wireless device off when

in any area with a potential explosive atmosphere and obey all signs and

instructions. Sparks in such areas could cause an explosion or fire resulting in

bodily injury or even death. Users are advised to switch the wireless device

off while at a refueling point (service station).

Users are reminded of the need to observe restrictions on the use of radio

equipment in fuel depots (fuel storage and distribution areas), chemical plants

or where blasting operations are in progress. Areas with a potentially

explosive atmosphere are often but not always, clearly marked. They include

below deck on boats, chemical transfer or storage facilities, vehicles using

liquefied petroleum gas (such as propane or butane), areas where the air

contains chemicals or particles, such as grain, dust, metal powders or

anesthetic gases, and other areas where you would normally be advised to

turn off your vehicle engine. Vehicles using liquefied petroleum gas (such as

propane or butane) must comply with the National Fire Protection Standard

(NFPA-58). For a copy of this standard, contact the National Fire Protection

Association.

 High Magnetic Flux Environments. The device contains ferrous

components so may constitute a physical projectile hazard if brought into high

Version 1.3 6AUG13 Page 5 of 9

magnetic flux environments such as found within Magnetic Resonance

Imaging (MRI) facilities.

 Luxury Leather Lanyard. Customers who use the luxury leather lanyard

should take extra care not to use the device in environments where there

may be a hazard when using this accessory as it does not incorporate a safety

break point.

Restricting Children’s Access to Your Device

 Your device is not a toy. Do not allow children to play with it because they

could hurt themselves and others or damage the device.

 Keep the device and all its parts and accessories out of reach of small

children.

Restriction of the Use of certain Hazardous Substances in Electrical and

Electronic Equipment (RoHS)

This device is fully RoHS-compliant. The European Union Directive 2002/95/EC

provides that new electrical and electronic equipment put on the market for the first

time from 1 July 2006 shall not contain more than permitted levels of lead,

cadmium, mercury, hexavalent chromium, polybrominated biphenyls (PBB), or

polybrominated diphenyl ethers (PBDE).

Waste Electrical and Electronic Equipment (WEEE)

(Applicable in the European Union and other European countries with

separate collection systems)

The use of the symbol as a marking on the equipment, accessories

or literature indicates that this product and its electronic accessories

(e.g. USB cable) may not be treated as household waste. By

ensuring this product is disposed of correctly, you will help prevent

potential negative consequences for the environment and human

health, which could otherwise be caused by inappropriate waste

handling of this product.

Household users should contact either their retailer where they purchased this

device, or their local government office, for details of where and how they can take

these items for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of

the purchasing contract. This device and its electronic accessories should not be

mixed with other commercial waste for disposal.

Version 1.3 6AUG13 Page 6 of 9

Correct Disposal of Batteries in this Device

(Applicable in the European Union and other European countries with

separate battery systems)

The use of the symbol as a marking on the battery, manual or

packaging indicates that the battery in this device should not be

disposed of with other household waste at the end of their working

life. Where marked, the chemical symbols Hg, Cd or Pb indicate that

the battery contains mercury, cadmium or lead above the reference

levels in EC Directive 2006/66. If batteries are not properly disposed

of, these substances can cause harm to human health or the

environment.

To protect natural resources, and to promote material reuse, please separate

batteries form other types of waste and recycle them through your local, free

battery return system.

The rechargeable battery incorporated in this device is not user replaceable. For

information on its replacement please contact OMG plc.

Specific Absorption Rate (SAR) Certification

For United States of American Customers (FCC)

Your device is a radio transmitter and receiver. It is designed and manufactured not

to exceed the exposure limits for RF energy set by the FCC. These FCC RF exposure

limits (FCC OETC65c – Body worn configuration) are derived from the

recommendations of the National Council on Radiation Protection and Measurement

(NCRP) and the Institute of Electrical and Electronic Engineers (IEEE). In both cases

the recommendations were developed by scientific and engineering experts drawing

from industry, government, and academia after extensive reviews of the scientific

literature related to the biological effects of RF energy.

The RF exposure limit set by the FCC for wireless body worn devices employs a unit

of measurement known as the Specific Absorption Rate (SAR) by the human body

expressed in units of watt per kilogram (WKg-1). The FCC requires wireless devices to

comply with a safety limit of 1.6 WKg-1. The FCC SAR limit incorporates a substantial

margin of safety to give additional protection to the public and to account for any

variations in measurements.

Tests were conducted with the device transmitting at its highest certified power in all

frequency bands to calculate SAR. This device holds an FCC ID: DMR OMGLIFEAP1

Specific publically available SAR levels for this device can be found at

http://www.fcc.gov/oet/ea/. Follow the instructions on the website and it should

provide values for typical or maximum SAR for the device.

Additional SAR information can also be obtained at

http://www.fcc.gov/encyclopedia/specific-absorption-rate-sar-cellualr-telephones.

Version 1.3 6AUG13 Page 7 of 9

For European Union Customers (R&TTE)

Your device conforms to European Union standard EN 62209-1 in the body worn

configuration that limit human exposure to Radio Frequency (RF) energy emitted by

radio and telecommunication equipment. This standard prevents the sale of wireless

devices that exceed a maximum exposure level, defined as the Specific Absorption

Rate (SAR) of 2.0 WKg-1.

Version 1.3 6AUG13 Page 8 of 9

CE Declaration of Conformity

Declaration of Conformity (R&TTE)

We, OMG plc

Unit 14 Minns Estate

Oxford OX2 0JB

United Kingdom

declare under our sole responsibility that the product

OMG LIFE Autographer

to which the declaration relates, is in conformity with the following standards and/or

OMG plc OMGLIFEAP1 Autographer User Manual Bonita Regulatory Information

OMG plc Autographer Bonita Regulatory Information

User guide regulatory info

Navigation menu

Namespaces

Views

Navigation