OPTOELECTRONICS OPA3201 Wireless USB Adapter User Manual

OPTOELECTRONICS Co., Ltd. Wireless USB Adapter Users Manual

Contents

Users Manual

Wireless USB Adapter OPA-3201 This manual provides specifications for the OPA-3201 wireless USB adapter. Specifications Manual
OPA-3201 Specifications Manual All information subject to change without notice. Document History Model Number: OPA-3201 Specification Number: SS14033 Edition: Original Spec Number: SS14025 Date: 2014- Copyright 2014 Opticon. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon. Limited Warranty and Disclaimers PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. Serial Number A serial number appears on all Opticon products. This official registration number is directly related to the device purchased. Do not remove the serial number from your Opticon device. Removing the serial number voids the warranty. Warranty Unless otherwise agreed in a written contract, all Opticon products are warranted against defects in materials and workmanship for two years after purchase. Opticon will repair or, at its option, replace products that are defective in materials or workmanship with proper use during the warranty period. Opticon is not liable for damages caused by modifications made by a customer. In such cases, standard repair charges will apply. If a product is returned under warranty and no defect is found, standard repair charges will apply. Opticon assumes no liability for any direct, indirect, consequential or incidental damages arising out of use or inability to use both the hardware and software, even if Opticon has been informed about the possibility of such damages. Packaging The packing materials are recyclable. We recommend that you save all packing material to use should you need to transport your scanner or send it for service. Damage caused by improper packaging during shipment is not covered by the warranty. Trademarks Trademarks used are the property of their respective owners. Opticon Inc. and Opticon Sensors Europe B.V. are wholly owned subsidiaries of OPTOELECTRONICS Co., Ltd., 12-17, Tsukagoshi 4-chome, Warabi-shi, Saitama, Japan 335-0002. TEL +81-(0) 48-446-1183; FAX +81-(0) 48-446-1184 SUPPORT USA Europe Phone: 800-636-0090 Email: support@opticonusa.com Email: support@opticon.com Web: www.opticonusa.com Web: www.opticon.com
OPA-3201 Specifications Manual Revision History Specification No. : SS14033 Product name : OPA-3201 Edition Date Page Section Description of Changes First 2014/ - - Initial release
OPA-3201 Specifications Manual Contents 1. Abstract..............................................................................................................................1 2. Overview ............................................................................................................................1 3. Basic Specifications .........................................................................................................2 4. Detailed View .....................................................................................................................3 5. Electrical Specifications ...................................................................................................4 5.1. USB ............................................................................................................................4 6. Interface Specifications ....................................................................................................4 6.1. USB Interface .............................................................................................................4 6.1.1. Connector ........................................................................................................................ 4 6.1.2. USB Interface Circuit....................................................................................................... 4 6.2. Wireless Interface.......................................................................................................5 6.2.1. HID Specifications ........................................................................................................... 5 7. Environmental Specifications ..........................................................................................6 7.1. Temperature...............................................................................................................6 7.2. Humidity .....................................................................................................................6 7.3. Vibration Strength (without packing)...........................................................................6 7.4. Vibration Strength (in individual packing) ...................................................................6 7.5. Drop Impact Strength (without packaging) .................................................................6 7.6. Drop Impact Strength (in individual packaging)..........................................................7 7.7. Electrostatic Discharge (ESD) Immunity ....................................................................7 8. Regulatory Compliance ....................................................................................................8 8.1. Product Safety............................................................................................................8 8.2. EMC ...........................................................................................................................8 8.3. Others.........................................................................................................................8 9. RoHS...................................................................................................................................9 10. Reliability .........................................................................................................................9 11. Precautions......................................................................................................................9 11.1. Handling ...................................................................................................................9 11.2. Radio Law ................................................................................................................9 11.3. Wireless Communication........................................................................................10 11.4. Frequency Baud .....................................................................................................10 12. Product Labels ..............................................................................................................11 13. Packaging Specifications .............................................................................................12 13.1. Individual Packaging ..............................................................................................12 13.2. Collective Packaging ..............................................................................................13
OPA-3201 Specifications Manual 14. Physical Features..........................................................................................................14 14.1. Dimensions.............................................................................................................14 14.2. Weight ....................................................................................................................14 14.3. Mechanical Drawing ...............................................................................................14
OPA-3201 Specifications Manual 1 1. Abstract This manual provides specifications for the OPA-3201 wireless USB adapter. 2. Overview The OPA-3201 is a USB adapter designed for Opticon wireless scanners, including the OPN-3200 and OPN-4200. ・ The OPA-3201 allows for wireless operation without special settings. ・ The OPA-3201 is simple and easy to use, just like USB scanners are. ・ The OPA-3201 can be used as a USB HID keyboard on a host device such as PC. ・ Alternative to the USB-HID keyboard interface, the OPA3201 can use the host's protocol stack via HCI (Host Controller Interface).
OPA-3201 Specifications Manual 2 3. Basic Specifications Item Specification Note CPU 32 bit RISC FROM 1 Mbyte Control Section SRAM 48 Kbyte Indicator LED Blue x 1 Frequency 2402 ~ 2480 MHz Specification IEEE 802.15.1 compliant Communication distance 10 m It may be shorter depending on usage environments Output level 4 dBm max Bluetooth Profile HID / SPP (HCI) Supporting SPP depends on host’s protocol stack Interface USB ・Full-Speed 12 Mbps (HID) ・Low-Power class Operating voltage 4.5 ~ 5.5 V Power SectionUSB Current consumption 100 mA or less USB power supply Operating -5 ~ 50°C Temperature Storage -20 ~ 60°C Operating 20 ~ 85%RH Humidity Storage 20 ~ 85%RH No condensing No frost Vibration 10 Hz ~ 100 Hz, acceleration of 19.6 m/s2, 60 minutes per cycle, repeat once in each X, Y and Z-direction Environmental Specifications Drop Drop the scanner 18 times (6 faces x 3) from the height of 150 cm onto a concrete floor Product safety EN60950-1:2005 IEC60950-1:2006 EMC EN 55022:2010 EN 301 489-1 V1.9.2 EN 301 489-17 V2.1.1 EN 300 328 V1.8.1 FCC Part 15 Subpart C, Subpart B ClassB VCCI Class B For residential, commercial and light-industrial environments Regulatory Compliance Other CE Marking Certification for Construction Design of Specified Radio Equipment No distraction Air discharge (direct): ±10 kV Immunity Test ESD No malfunction Air discharge (direct): ±8 kV Conditions: IEC61000-4-2 compliant Dimensions 43.8 × 8.3 × 17.4 (WDH mm) Physical Features Weight Approx. 6 g
OPA-3201 Specifications Manual 3 4. Detailed View Figure 1: Detailed View of OPA-3201 No Name Description 1 USB connector A connector to connect to the host 2 Address label The OPA-3201’s address bar code. A wireless connection can be established by reading this label with a scanner.
OPA-3201 Specifications Manual 4 5. Electrical Specifications 5.1. USB Power supply voltage : 4.5 ~ 5.5 V Bus-Power class : Low-Power Current consumption : 100 mA or less 6. Interface Specifications The OPA-3201 supports two types of interfaces; USB and wireless. 6.1. USB Interface The USB-HID interface is supported. 6.1.1. Connector Signal name Pin No. VCC 1 Data(-) 2 Data(+) 3 GND 4 Figure 2: USB Plug (A): 6.1.2. USB Interface Circuit Figure 3: Interface Circuit (USB) Front view 3214Bluetooth Controller Data(+) Data(-) VCC GND USB connector +5.0 V power supply
OPA-3201 Specifications Manual 5 6.2. Wireless Interface The OPA-3201 uses IEEE 802.15.1 as the wireless interface. 6.2.1. HID Specifications Frequency : 2402 ~ 2480 MHz Specification : IEEE 802.15.1 compliant Communication distance : 10 m Output level : 4 dBm max Implemented profile : HID Communication configuration : 1 to 1 Operating mode in communication : Slave mode Security mode : Authentication supported Encryption : Encryption supported
OPA-3201 Specifications Manual 6 7. Environmental Specifications 7.1. Temperature The performance is guaranteed when the range of ambient temperature is the following values: Operating temperature : -5 ~ 50 °C Storage temperature : -20 ~ 60°C 7.2. Humidity The performance is guaranteed when the range of ambient humidity is the following values: Operating humidity : 20 ~ 85% RH (no condensation, no frost) Storage humidity : 20 ~ 85% RH (no condensation, no frost) 7.3. Vibration Strength (without packing) There shall be no sign of malfunction after the following vibration test. Vibration test: Increase the frequency of the vibration from 10Hz to 100Hz at an accelerated velocity of 19.6m/s2 (2.0 G) for 30 minutes (60 minutes per cycle) in the non-operating state. Repeat this in each X, Y and Z direction. 7.4. Vibration Strength (in individual packing) There shall be no sign of malfunction after the following vibration test. Vibration test: Increase the frequency of the vibration from 10Hz to 100Hz at an accelerated velocity of 19.6 m/s2 (2.0 G) for 30 minutes (60 minutes per cycle) in individually packaged state. Repeat this in each X, Y and Z direction. 7.5. Drop Impact Strength (without packaging) There shall be no sign of malfunction after the following drop test. Drop test: Drop the scanner 18 times in total (3 times at each 6 face) from a height of 75 cm onto a concrete floor as shown below. Figure 4: Drop Test
OPA-3201 Specifications Manual 7 7.6. Drop Impact Strength (in individual packaging) There shall be no sign of malfunction after the following drop test. Drop test: Drop an individually packaged scanner 10 times in total, at any of 1 corner, 3 edges, and 6 faces, from a height of 150 cm onto a concrete floor. 7.7. Electrostatic Discharge (ESD) Immunity Aerial discharge : ±8 kV max (no malfunction) ±10 kV max (no distraction) Measurement environment : Testing method compliant with IEC-61000-4-2. Discharge resistance : 330 Ω Charging capacitor : 150 pF
OPA-3201 Specifications Manual 8 Federal Communications Commission Notices This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Harmful Interference Notice This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment or devices • Connect the equipment to an outlet other than the receiver's • Consult a dealer or an experienced radio/TV technician for assistance Changes or modifications to this equipment that have not been approved by Ruckus Wireless may void the user's authority to operate this equipment. 8. Regulatory Compliance 8.1. Product Safety EN60950-1:2005 IEC60950-1:2006 8.2. EMC R&TTE Directive ・EN 55022:2010 ・EN 301 489-1 V1.9.2 ・EN 301 489-17 V2.1.1 ・EN 300 328 V1.8.1 FCC Part 15 Subpart B Class B VCCI Class B 8.3. Others ・Certification for Construction Design of Specified Radio Equipment This is a Class B product, to be used in a domestic environment, based on the Technical Requirement of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it  may cause radio interference. RF Exposure Information This product complies with FCC radiation exposure limits set forth for an uncontrolled environment.
OPA-3201 Specifications Manual 9 9. RoHS The OPA-3201 is compliant with RoHS. RoHS: The restriction of the use of certain hazardous substances in electrical and electronic equipment, 2011/65/EC 10. Reliability MTBF (Mean Time Between Failures) 10,000 hours 11. Precautions 11.1. Handling Handle this product carefully. Do not deliberately subject it to any of the following. (1) Shock: ・Do not drop this product from a height greater than specified in this manual. ・Do not place this product under or between any heavy items. (2) Temperature Conditions: ・Do not use this product at temperatures outside the specified range. ・Do not pour boiling water on this product. ・Do not throw this product into a fire. (3) Foreign Materials: ・Do not immerse this product in water or other liquid. ・Do not expose this product to chemicals. (4) Others ・Do not disassemble this product. ・Do not use this product near a radio or a TV. It may cause reception problems. ・This product may be affected by a momentary voltage drop caused by lightning. 11.2. Radio Law This product qualifies as specified radio equipment for radio stations of 2.4 GHz band data communication system and has obtained the Certification for Construction Design of Specified Radio Equipment. Therefore, radio station license is not required in Japan. The following activities are prohibited under the Radio Law: ・Remodeling and disassembly ・Peeling off the certificate label Do not use this equipment under the following environment, as radio interference may affect other device and end up with causing physical or material damage. ・Safety apparatus and medical device for human body protection ・Environment where is concerned to cause serious damage
OPA-3201 Specifications Manual 10 11.3. Wireless Communication ・This product supports wireless communication with other devices that have the same specifications (profile). ・A wireless connection to any device other than Opticon products is not guaranteed. ・This product and the Opticon wireless scanners use the 2.4 GHz frequency band that is shared among other devices. It may affect the communication speed and distance between this product and the scanners. ・The communication speed and distance vary depending on the interference and radio wave condition between this product and the scanners. 11.4. Frequency Baud This product uses the 2.4 GHz frequency band. Read carefully the followings before using this product. In the frequency band of this product, scientific, medical and industrial devices including microwaves are used. Also other radio stations including local private radio station for mobile object identification requiring license for such as manufacturing lines at factories, specific power-saving radio station requiring no license and amateur radio station are managed. 1. Make sure that “other radio stations” are not managed in the frequency band 2.4 GHz before using this product. 2. In case that radio interference occurs between this product and “other radio stations,” change the service space immediately, or stop transmitting radio wave to avoid the interference. 3. If you have any questions or troubles, please contact our sales office.
OPA-3201 Specifications Manual 11 12. Product Labels The product label is affixed to the back of the OPN-3201 as shown below. Figure 5: Product Labels
OPA-3201 Specifications Manual 12 13. Packaging Specifications 13.1. Individual Packaging Assembled package size: xxx × xxx × xxx (WDH mm) Figure 6: Individual Packaging
OPA-3201 Specifications Manual 13 13.2. Collective Packaging Quantity : 100 pcs Assembled package size : xxx × xxx × xxx (WDH mm) Figure 7: Collective Packaging * ‘Ro mark’ on the boxes for the product indicates that the product is RoHS compliant declared by Optoelectronics Co., Ltd.
OPA-3201 Specifications Manual 14 14. Physical Features 14.1. Dimensions 43.8 × 8.3 × 17.4 (WDH mm) 14.2. Weight Approx. 6 g (excluding accessories) 14.3. Mechanical Drawing Figure 8: Mechanical Drawing [Unit: mm]

Navigation menu