OPTOELECTRONICS OPC3301I Handy Image Scanner User Manual OPC 3301i Master Spec ENG1
OPTOELECTRONICS Co., Ltd. Handy Image Scanner OPC 3301i Master Spec ENG1
User Manual
Handheld Bluetooth 1D CCD Scanner OPC-3301i This manual provides specifications for the OPC3301i handheld Bluetooth 1D CCD scanner. Specifications Manual OPC-3301i Specifications Manual All information subject to change without notice. Document History Model Number: OPC-3301i Specification Number: (SS14023) Edition: 1st Original Spec Number: (SS14018) Date: 2014-10-20 Copyright 2014 Opticon. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon. Limited Warranty and Disclaimers PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. Serial Number A serial number appears on all Opticon products. This official registration number is directly related to the device purchased. Do not remove the serial number from your Opticon device. Removing the serial number voids the warranty. Warranty Unless otherwise agreed in a written contract, all Opticon products are warranted against defects in materials and workmanship for two years after purchase. Opticon will repair or, at its option, replace products that are defective in materials or workmanship with proper use during the warranty period. Opticon is not liable for damages caused by modifications made by a customer. In such cases, standard repair charges will apply. If a product is returned under warranty and no defect is found, standard repair charges will apply. Opticon assumes no liability for any direct, indirect, consequential or incidental damages arising out of use or inability to use both the hardware and software, even if Opticon has been informed about the possibility of such damages. Packaging The packing materials are recyclable. We recommend that you save all packing material to use should you need to transport your scanner or send it for service. Damage caused by improper packaging during shipment is not covered by the warranty. Trademarks Trademarks used are the property of their respective owners. Opticon Inc. and Opticon Sensors Europe B.V. are wholly owned subsidiaries of OPTOELECTRONICS Co., Ltd., 12-17, Tsukagoshi 4-chome, Warabi-shi, Saitama, Japan 335-0002. TEL +81-(0) 48-446-1183; FAX +81-(0) 48446-1184 SUPPORT USA Europe Phone: 800-636-0090 Email: support@opticonusa.com Email: support@opticon.com Web: www.opticonusa.com Web: www.opticon.com OPC-3301i Specifications Manual Revision History Specification No. Product name Edition First : (SS14023) : OPC-3301i Date 2014/10/20 Page Section Description of Changes Initial release OPC-3301i Specifications Manual Contents 1. Abstract ............................................................................................................................................. 1 2. Overview............................................................................................................................................ 1 3. Basic Specifications......................................................................................................................... 2 4. Detailed View .................................................................................................................................... 4 5. Electrical Specifications .................................................................................................................. 5 5.1. Current Consumption................................................................................................................ 5 5.2. Operating Time and Charging Time ......................................................................................... 5 6. Interface Specifications ................................................................................................................... 5 6.1. Bluetooth ................................................................................................................................... 5 7. Optical Specifications ...................................................................................................................... 6 7.1. Basic Optical Specifications...................................................................................................... 6 7.2. Aiming Pattern .......................................................................................................................... 6 8. Technical Specifications.................................................................................................................. 7 8.1. Bar Code Test Sample.............................................................................................................. 7 8.2. Scan Area and Depth of Field................................................................................................... 8 8.3. Printed Contrast Signal (PCS) .................................................................................................. 9 8.4. Minimum Resolution ................................................................................................................. 9 8.5. Wide Bar Code.......................................................................................................................... 9 8.6. Pitch, Skew and Tilt ................................................................................................................ 10 8.7. Curvature ................................................................................................................................ 10 8.8. Scanning from LCD Screen .................................................................................................... 11 8.9. Auto Trigger ............................................................................................................................ 11 8.9.1. Stand Detection ............................................................................................................. 11 8.9.2. Auto Trigger Operation.................................................................................................. 12 9. Environmental Specifications ....................................................................................................... 13 9.1. Temperature............................................................................................................................ 13 9.2. Humidity .................................................................................................................................. 13 9.3. Ambient Light Immunity .......................................................................................................... 13 9.4. Dust and Drip Proof ................................................................................................................ 13 9.5. Vibration Strength (without packing)....................................................................................... 13 9.6. Vibration Strength (in individual packing) ............................................................................... 14 9.7. Drop Impact Strength (without packaging) ............................................................................. 14 9.8. Drop Impact Strength (in individual packaging) ...................................................................... 14 9.9. Electrostatic Discharge (ESD) Immunity................................................................................. 14 10. Regulatory Compliance ............................................................................................................... 15 10.1. LED Safety ............................................................................................................................ 15 10.2. Product Safety ...................................................................................................................... 15 OPC-3301i Specifications Manual 10.3. EMC ...................................................................................................................................... 15 10.4. Others ................................................................................................................................... 16 11. RoHS .............................................................................................................................................. 16 12. Reliability....................................................................................................................................... 16 13. Precautions ................................................................................................................................... 16 13.1. Handling ................................................................................................................................ 16 13.2. Radio Law ............................................................................................................................. 17 13.3. Bluetooth ............................................................................................................................... 17 13.4. Frequency Baud.................................................................................................................... 17 14. Product Labels.............................................................................................................................. 18 15. Packaging Specifications ............................................................................................................ 19 15.1. Individual Packaging ............................................................................................................. 19 15.2. Collective Packaging............................................................................................................. 20 16. Physical Features ......................................................................................................................... 21 16.1. Dimensions ........................................................................................................................... 21 16.2. Weight ................................................................................................................................... 21 16.3. Mechanical Drawing.............................................................................................................. 21 17. Supported Symbologies .............................................................................................................. 22 17.1. Default Setting ...................................................................................................................... 22 17.2. Supported Symbologies........................................................................................................ 22 17.2.1. 1D Bar Codes .............................................................................................................. 22 17.2.2. GS1 Databar, Composite Code................................................................................... 23 OPC-3301i Specifications Manual 1. Abstract This manual provides specifications for the OPC-3301i handheld Bluetooth 1D CCD scanner. 2. Overview The OPC-3301i is a handheld 1D scanner with a built-in CCD imager that enables high speed scanning of standard linear (1D) symbologies. The scanned data is output via Bluetooth. ・ All bar code data scanned is transmitted to a host device through the Bluetooth interface. ・ The scanner can work with many Bluetooth-enabled host devices, such as PCs, tablet PCs and smart phones. ・ Bluetooth SPP (Serial Port Profile) and HID (Human Interface Device Profile) are implemented. ・ The scanner can read bar codes from LCD screens. ・ This scanner is equipped with a vibrating function that can signal certain events to the users even in noisy environments. Additionally it has a buzzer and a LED indicator. ・ A single red LED aiming line toward a target bar code can help the users find the appropriate scanning position. ・ Special antimicrobial treatment is applied to the chassis, and alcohol can be used to wipe the scanner clean (except for the scanning window and the logo panel). ・ The power source is 3.7 V 1100 mAh (typ.) lithium-ion battery. ・ A dedicated charging cradle CHG-3201 is supplied for recharging and easy storage of the scanner. ・ The scanner is Apple MFi certified. OPC-3301i Specifications Manual 3. Basic Specifications Item Specification Control Section Input Section Indicator CPU 32 bit CISC / 96 MHz FROM 512 Kbyte + 32 Kbyte SRAM 96 Kbyte FROM (storage) 1 Mbyte Key type 1 key: trigger LED 2 colors (red, green) and 1 color (blue) Buzzer Loudness (3-level) / tone adjustable Vibration motor Strength (3-level) / duration adjustable Interface Bluetooth Note For data area only Frequency 2402 ~ 2480 MHz Specification Bluetooth Ver 2.1 compliant Communication distance 10 m It may be shorter depending on usage environments Output level Class 2 Max output 4 dBm Profile SPP / HID Optical Section Scan method CCD linear image sensor Light source 1 red LED Effective pixels 1500 pixels View angle Horizontal: approx. 50° Symbologies JAN, EAN, UPC-A, UPC-E, NW-7 (Codabar), Industrial 2 of 5, Interleaved 2 of 5, Code 11, Code 39,Code 93,Code 128 etc. Refer to Chapter 17. for details Minimum resolution Code 39 : 0.1 mm PCS 0.9 R ≥ 15 mm (8-digit JAN) R ≥ 20 mm (13-digit JAN) 110 mm wide 0.2 mm resolution Code 39 (DOF 150 mm) is readable: Curvature Supported 1D Symbologies Wide bar code PCS 0.9 Pitch : ±50° Scan angle Skew : ±65° (excluding dead zone) Tilt Depth of field (mm) Minimum PCS Code 39 : ±25° Resolution (0.127) 55 ~ 75 Resolution (0.15) 45 ~ 100 Resolution (0.25) 35 ~ 175 Resolution (0.5) 40 ~ 300 Resolution (1.0) 60 ~ 500 0.3 or more MRD 32% or more OPC-3301i Specifications Manual Item Specification On LCD screen Note Brightness of white space 30 cd/m or more Contrast ratio 100:1 or more Power Section Main battery Lithium-ion 1100 mAh (typ.) Charge the battery before initial use Up-time 48 hours or more *1 Operating (charging) voltage 5.0 ~ 6.5V Current consumption Charging Less than 1 A Operating 0 ~ 50°C Storage -20 ~ 60°C Operating 20 ~ 85% Storage 20 ~ 85% Fluorescent 10,000 lx or less Sunlight 100,000 lx or less Temperature Environmental Specifications Humidity Ambient light immunity Charging with charger No condensing No frost 10 Hz ~ 100 Hz, acceleration of 19.6 m/s2, 60 minutes per cycle, repeat once in each X, Y and Z-direction Drop the scanner 30 times (6 faces x 5) from the height of 150 cm onto a concrete floor Vibration Drop Dust and drip proof IP42 equivalent LED safety IEC 62471-1:2006 Exempt_Group Regulatory Compliance EN60950-1:2005 IEC60950-1:2006 EN 55022:2010 EN 301 489-1 V1.9.2 EN 301 489-17 V2.1.1 EN 300 328 V1.8.1 FCC Part 15 Subpart C, Subpart B ClassB VCCI Class B Bluetooth logo certification MFi license CE Marking Certification for Construction Design of Specified Radio Equipment Product safety EMC Other Immunity Test ESD No distraction Air discharge (direct): ±15 kV No malfunction Contact discharge (direct / indirect): ±6 kV Air discharge (direct): ±8 kV Physical Features Dimensions 113 × 56 × 132 (WDH mm) Weight Approx. 127 g Peak Wavelength 624 nm For residential, commercial and lightindustrial environments Conditions: IEC61000-4-2 compliant Excluding accessories *1: When a bar code is read twice every 10 seconds at room temperature in a const Bluetooth connection (SPP master mode). OPC-3301i Specifications Manual 4. Detailed View Figure 1: Detailed View of OPC-3301i No Name Description Trigger Key A key to read bar codes Scan Window LED illumination is emitted from this window to read bar codes. Status LED The operating statuses, such as bar code reading, Bluetooth connection and warning, are indicated by different colors. Buzzer Holes A sound from a built-in buzzer comes out through these holes. Charging terminals Charging pins connected to the dedicated charging cradle CHG-3201 OPC-3301i Specifications Manual 5. Electrical Specifications 5.1. Current Consumption Standby Sleep Item Specification 15 mA or less 1 mA or less Operating 200 mA or less Measurement condition Power voltage 3.7 V at 25 °C Note With wireless connection Reading, communications, LED, vibration motor activated 5.2. Operating Time and Charging Time Item Sleep Battery Standby duration Reading Charging time Specification 200 hours or more Approx. 72 hours Approx. 48 hours Approx. 3 hours Note With wireless connection 1 scan / 5 secs with wireless connection With AC adaptor power supply * The above specifications may not be met when the battery pack has been deteriorated. 6. Interface Specifications 6.1. Bluetooth Frequency : 2402 ~ 2480 MHz Specification : Bluetooth Ver 2.1 compliant Communication distance : 10 m Output level : Class 2 (max 4 dBm) Implemented profile : SPP / HID Communication configuration : 1 to 1 Operating mode in communication : Master / Slave mode Security mode : Authentication supported Encryption : Encryption supported OPC-3301i Specifications Manual 7. Optical Specifications 7.1. Basic Optical Specifications Item Characteristics Scan method CCD linear image sensor Effective pixel Horizontal 1500 dots Image capture speed (*1) Scan rate 300 scans/sec Focal distance Distance from the front edge of scanner 105 mm View angle Horizontal Approx. 50° Red LED Peak wavelength 624 nm Maximum radiation output (*2) 12 lm Light source *1 The fastest seed of image capture *2 Reference value based on the datasheet (25°C, luminous efficiency 60lm/W, IF = 100 mA ). 7.2. Aiming Pattern The aiming is used for the following purpose: 1. Light source for bar code reading 2. Light source to indicate the appropriate reading range The aiming specifications are as follows: ・ An optical axis of imaging field of view and the center of horizontal aiming width coincide at a distance of L=60±10 mm from the front edge of the scanner. ・ The horizontal aiming width to the horizontal width of imaging filed of view at a distance of L=60 mm is 100%±10%. Aiming Width Horizontal FOV Figure 2: Aiming Pattern and Imaging Range OPC-3301i Specifications Manual 8. Technical Specifications The conditions for technical specifications are as follows unless otherwise specified in each section.Temperature and humidity Ambient light Angles Curvature Power supply voltage Reading test Bar code test sample : Room temperature, room humidity : 200 ~ 300 lx : Pitch: α = 0°, Skew: β = 15°, Tilt: γ = 0° :R=∞ : 3.7 V : 1 read in 0.5 sec or less. Accept the performance with 10 consecutive successes : OPTOELECTRONICS test samples. Refer to Section 8.1. for details. 8.1. Bar Code Test Sample Resolution 1.0 mm 0.5 mm 0.25 mm 0.2 mm 0.15 mm 0.127 mm 0.1 mm Quiet Zone ( mm 25 18 mm 10 mm 10 mm 7 mm 5 mm 5 mm No. of Digits 34 10 PCS Quiet Zone ( mm 10 0.9 10 mm 10 mm No. of Digits 13 13 Symbology PCS Code 39 0.9 Symbology JAN
Resolution 0.26 mm 0.26 mm 0.33 mm OPC-3301i Specifications Manual 8.2. Scan Area and Depth of Field The scan area is within the arc centered on the scan origin as shown in each resolution, which is measured from the front edge of the scanner. 60 50 150 100 200 250 300 350 400 450 500 550 Scanning may not be possible within this range Resolution 0.127 55 45 75 Resolution 0.15 100 Resolution 0.25 35 175 Resolution 0.5 40 60 300 Resolution 1.0 Figure 3: Scan Area and Depth of Field 500 (Unit: mm) 600 OPC-3301i Specifications Manual 8.3. Printed Contrast Signal (PCS) 0.3 or higher MRD Distance Bar code : 32% and higher (70% or higher reflectivity of space and quiet zone) : 72 mm from the front edge of the scanner : JAN (resolution 0.26 mm, PCS 0.3) specified in Section 8.1. MRD = Minimum reflectance of white space - Maximum reflectance of black bar PCS = Reflectance of white spece - Reflectance of black bar Reflectance of white space * Be sure to keep the optical window clean without dirt or scratches, or it may have a bad effect on the reading characteristics. 8.4. Minimum Resolution 0.1 mm or more Bar code Distance Angle Curvature : Code 39 (resolution 0.1 mm) specified in Section 8.1. : 72 mm from the front edge of the scanner : α = 0°, β = + 15°, γ = 0° :R=∞ 8.5. Wide Bar Code Code 39 with width of 110 mm and resolution of 0.2 mm can be read Bar code Distance Angle Curvature : Code 39 (resolution 0.20 mm, PCS 0.9) specified in Section 8.1. : 127 mm from the front edge of the scanner : α = 0°, β = +15°, γ = 0° :R=∞ Figure 4: Wide Bar Code OPC-3301i Specifications Manual 8.6. Pitch, Skew and Tilt Pitch Skew Dead zone Tilt Bar code Distance Curvature Angle : α = ±50° : β = ±65° : β = ±8° : γ = ±25° : JAN (resolution 0.33 mm) specified in Chapter 8.1 : 72 mm from the front edge of the scanner :R=∞ : Pitch β = +15°, γ = 0° Skew, Dead zone α = 0°, γ = 0° Tilt α = 0°, β = +15° α β γ Figure 5: Pitch, Skew and Tilt 8.7. Curvature 0.26 mm 8-digit JAN 0.26 mm 13-digit JAN Bar code Distance Angle : R ≥ 15 mm : R ≥ 20 mm : JAN (resolution 0.26 mm) specified in Section 8.1. : 127 mm from the front edge of the scanner : α = 0°, β = +15°, γ = 0° Bar code Figure 6: Curvature * The reading characteristics may deteriorate due to the specular reflection of LED illumination when the reflectivity is high. 10 OPC-3301i Specifications Manual 8.8. Scanning from LCD Screen Bar codes displayed on LCD screens (brightness of white part 30 cd/m2 or more, contrast ratio 100:1) can be read. Bar code Ambient light Distance Angle LCD screen type Contrast ratio = : JAN (resolution 0.26 mm) specified in Section 8.1. : 100 lx or less : 127 mm from the front edge of the scanner : α = 0°, β = 0°, γ = 0° : Transmissive (backlight) TFT Brightness of white parts Brightness of black parts * The bar code resolution is the value when displayed on the LCD screen. * The width of bar code element is an integral multiple of pixel width of LCD screen. * The reading characteristics may deteriorate due to the specular reflection of LED illumination when the reflectivity is high. 8.9. Auto Trigger When the scanner is placed in a dedicated stand (sold separately) which contains a magnet, it can detect this magnet and enters auto trigger mode. The scanner starts scanning automatically when it detects a change in brightness that occurs when a bar code label is presented in front of it. 8.9.1. Stand Detection “Stand detection - Auto trigger flow” Is Stand Detection mode “*4” enabled? No Yes Is the scanner in the stand? No Yes Manual Trigger Auto Trigger Figure 7: Stand Detection Flow * The dedicated stand is an optional accessory that can be purchased separately. * The stand detection mode is disabled by default. It must be enabled to be used. 11 OPC-3301i Specifications Manual 8.9.2. Auto Trigger Operation The scanner has an optional auto trigger mode in which it starts to read a bar code automatically when it detects one. When auto trigger mode is enabled, the scanner tries to detect bars at regular intervals and when it detects 18 or more bars, it enters read mode in which it tries to decode a bar code. When the scanner continues to detect bars after the reading has been done, it will assume those bars are from the same bar code as the previous one and will not attempt to read it. When the detecting conditions are not met, the scanner will perform the intermittent scanning again until the next bar code is detected. Angle of paper Temperature / Humidity Ambient light : Skew angle, excluding pitch angle and dead zone, specified in Section 8.6 : Room temperature / room humidity : 500 ~ 1000 lx Paper Detection range Figure 8: Auto Trigger 12 OPC-3301i Specifications Manual 9. Environmental Specifications 9.1. Temperature Scanning performance is guaranteed when the range of ambient temperature around the scanner is the following values: Operating temperature Storage temperature : 0 ~ 50 °C : -20 ~ 60°C 9.2. Humidity Scanning performance is guaranteed when the range of ambient humidity around the scanner is the following values: Operating humidity Storage humidity : 20 ~ 85% RH (no condensation, no frost) : 20 ~ 85% RH (no condensation, no frost) 9.3. Ambient Light Immunity Scanning performance is guaranteed when the range of illumination on a bar code surface is between zero and the following values: Incandescent light Fluorescent light Sunlight : 10,000 lx : 10,000 lx : 100,000 lx Bar code Distance Angle Curvature Power supply voltage : JAN (resolution 0.26 mm) specified in Section 8.1. : 72 mm from the front edge of the camera module : α = 0°, β =+15°, γ = 0° :R=∞ : 3.7 V * Be sure that the direct light or specular reflection from the light source does not enter the light receiving section of the scanner. 9.4. Dust and Drip Proof IEC IP42 equivalent Protection against solid objects: Level 4 equivalent Protected against solid objects greater than 1.0 mm Protection against liquids: Level 2 (JIS IPX2) equivalent Protected against dripping water from the vertical when tilted up to 15° * () is JIS drip-proof type. 9.5. Vibration Strength (without packing) There shall be no sign of malfunction after the following vibration test. Vibration test: Increase the frequency of the vibration from 10Hz to 100Hz at an accelerated velocity of 19.6m/s2 (2.0 G) for 30 minutes (60 minutes per cycle) in the non-operating state. Repeat this in each X, Y and Z direction. 13 OPC-3301i Specifications Manual 9.6. Vibration Strength (in individual packing) There shall be no sign of malfunction after the following vibration test. Vibration test: Increase the frequency of the vibration from 10Hz to 100Hz at an accelerated velocity of 19.6 m/s2 (2.0 G) for 30 minutes (60 minutes per cycle) in individually packaged state. Repeat this in each X, Y and Z direction. 9.7. Drop Impact Strength (without packaging) There shall be no sign of malfunction after the following drop test. Drop test: Drop the scanner 30 times in total (5 times at each 6 face) from a height of 150 cm onto a concrete floor as shown below. 150cm 150 cm Concret Figure 9: Drop Test 9.8. Drop Impact Strength (in individual packaging) There shall be no sign of malfunction after the following drop test. Drop test: Drop an individually packaged scanner 10 times in total, at any of 1 corner, 3 edges, and 6 faces, from a height of 150 cm onto a concrete floor. 9.9. Electrostatic Discharge (ESD) Immunity Contact discharge Aerial discharge : ±6 kV max (direct or indirect discharge, no malfunction) : ±8 kV max (no malfunction) ±15 kV max (no distraction) Measurement environment Discharge resistance Charging capacitor : Testing method compliant with IEC-61000-4-2. : 330 Ω : 150 pF 14 OPC-3301i Specifications Manual 10. Regulatory Compliance 10.1. LED Safety IIEC 62471-1:2006 Exempt_Group 10.2. Product Safety EN60950-1:2005 IEC60950-1:2006 10.3. EMC R&TTE Directive ・EN 55022:2010 ・EN 301 489-1 V1.9.2 ・EN 301 489-17 V2.1.1 ・EN 300 328 V1.8.1 FCC Part 15 Subpart B Class B Federal Communications Commission Notices This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Harmful Interference Notice This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment or devices • Connect the equipment to an outlet other than the receiver's • Consult a dealer or an experienced radio/TV technician for assistance Changes or modifications to this equipment that have not been approved by Ruckus Wireless may void the user's authority to operate this equipment. RF Exposure Information This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. VCCI Class B This is a Class B product, to be used in a domestic environment, based on the Technical Requirement of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. 15 OPC-3301i Specifications Manual 10.4. Others ・Bluetooth logo certification ・MFi license “Made for iPod,” “Made for iPhone,” and “Made for iPad” mean that an electronic accessory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards.Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless performance. ・Certification for Construction Design of Specified Radio Equipment ・Classification of Specified Radio Equipment ・Model Name ・Certificate Number Article 2 Paragraph 1, Item 19 Low power data communication system in 2.4 GHz band OPA-26X1 201-125603 11. RoHS The OPC-3301i is compliant with RoHS. RoHS: The restriction of the use of certain hazardous substances in electrical and electronic equipment, 2011/65/EU 12. Reliability MTBF (Mean Time Between Failures) 10,000 hours 13. Precautions 13.1. Handling Handle this product carefully. Do not deliberately subject it to any of the following. (1) Shock: ・Do not drop this product from a height greater than specified in this manual. ・Do not place this product under or between any heavy items. ・Do not swing the cable around. (2) Temperature Conditions: ・Do not use this product at temperatures outside the specified range. ・Do not pour boiling water on this product. ・Do not throw this product into a fire. (3) Foreign Materials: ・Do not immerse this product in water or other liquid. ・Do not expose this product to chemicals. 16 OPC-3301i Specifications Manual (4) Others ・Do not disassemble this product. ・Do not use this product near a radio or a TV. It may cause reception problems. ・This product may be affected by a momentary voltage drop caused by lightning. ・iPhone, iPad and iPod are trademarks of Apple Inc. ・Other company and product names may be trademarks of their respective owners. 13.2. Radio Law This product qualifies as specified radio equipment for radio stations of 2.4 GHz band data communication system and has obtained the Certification for Construction Design of Specified Radio Equipment. Therefore, radio station license is not required in Japan. The following activities are prohibited under the Radio Law: ・Remodeling and disassembly ・Peeling off the certificate label Do not use this equipment under the following environment, as radio interference may affect other device and end up with causing physical or material damage. ・Safety apparatus and medical device for human body protection ・Environment where is concerned to cause serious damage 13.3. Bluetooth ・This product supports Bluetooth wireless communication with other Bluetooth devices that have the same profile ・This product complies with Bluetooth standards; however, its communication performance with untested devices is not guaranteed. ・Bluetooth devices use the 2.4 GHz frequency band that is shared among other devices. It may affect the communication speed and distance between this product and the host device. ・The communication speed and distance vary depending on the interference and radio wave condition between this product and the host device. 13.4. Frequency Baud This product uses the 2.4 GHz frequency band. Read carefully the followings before using this product. In the frequency band of this product, scientific, medical and industrial devices including microwaves are used. Also other radio stations including local private radio station for mobile object identification requiring license for such as manufacturing lines at factories, specific power-saving radio station requiring no license and amateur radio station are managed. 1. Make sure that “other radio stations” are not managed in the frequency band 2.4 GHz before using this product. 2. In case that radio interference occurs between this product and “other radio stations,” change the service space immediately, or stop transmitting radio wave to avoid the interference. 3. If you have any questions or troubles, please contact our sales office. 17 OPC-3301i Specifications Manual 14. Product Labels The product labels are affixed to the scanner as shown below. Product label Logo label Figure 10: Product Labels Product label Shows the product name, serial number, and month and year of manufacture. Logo label Shows the standards-compliant languages and logos. 18 OPC-3301i Specifications Manual 15. Packaging Specifications 15.1. Individual Packaging Assembled package size: 165 × 110 × 82 (WDH mm) Figure 11: Individual Packaging 19 OPC-3301i Specifications Manual 15.2. Collective Packaging Assembled package size : 585 × 520 × 200 (WDH mm) Figure 12: Collective Packaging * ‘Ro mark’ on the boxes for the product indicates that the product is RoHS compliant declared by Optoelectronics Co., Ltd. 20 OPC-3301i Specifications Manual 16. Physical Features 16.1. Dimensions 56 × 113 × 132 (WDH mm / excluding protruding portion) 16.2. Weight Approx. 127 g (excluding accessories) 16.3. Mechanical Drawing (113) (56) (132) Figure 13: Mechanical Drawing 21 OPC-3301i Specifications Manual 17. Supported Symbologies 17.1. Default Setting The scanner is set to default settings by reading the following menu labels. Function SET Default END Menu label Menu code _ZZ_ _SO_ _ZZ_ ZZ SO ZZ 17.2. Supported Symbologies 17.2.1. 1D Bar Codes Code type UPC UPC Add-on 2 UPC Add-on 5 EAN (JAN) EAN Add-on 2 EAN Add-on 5 EAN-13 EAN-13 Add-on 2 EAN-13 Add-on 5 EAN-8 EAN-8 Add-on 2 EAN-8 Add-on 5 Code 39 Default Minimum length ○ ○ Note ○ ○ ○ Not transmit ST/SP Tri-Optic ○ Not transmit ST/SP Codabar (NW7) ○ Not transmit ST/SP Industrial 2 of 5 ○ Interleaved 2 of 5 ○ ○ Code 128 ○ Code 93 ○ IATA ○ MSI/Plessey ○ UK/Plessey ○ TELEPEN ○ S-Code Code 11 Matrix 2 of 5 Chinese Post Matrix 2 of 5 Korean Postal Authority 22 GS1 conversion (setting required) OPC-3301i Specifications Manual 17.2.2. GS1 Databar, Composite Code Code type GS1 DataBar ・GS1 DataBar Omnidirectional ・GS1 DataBar Truncated ・GS1 DataBar Stacked ・GS1 DataBar Stacked Omnidirectional GS1 DataBar Limited GS1 DataBar Expanded ・GS1 DataBar Expanded ・GS1 DataBar Expanded Stacked Default Note ○ GS1 conversion (setting required) ○ ○ * The supported symbologies vary depending on specifications for the application to be loaded. 23
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Producer : Acrobat Distiller 8.0.0 (Windows) Creator Tool : PScript5.dll Version 5.2 Modify Date : 2014:10:21 15:52:09+09:00 Create Date : 2014:10:21 15:52:09+09:00 Format : application/pdf Title : Microsoft Word - OPC-3301i_Master Spec_ENG1.doc Creator : tyamazaki0304 Document ID : uuid:be01692a-be79-4129-945b-6fb5f4b52dad Instance ID : uuid:67917b9d-ce57-45c3-b4b3-735d49e8bbee Page Count : 28 Author : tyamazaki0304EXIF Metadata provided by EXIF.tools