OPTOELECTRONICS OPN3200N Handy Image Scanner User Manual
OPTOELECTRONICS Co., Ltd. Handy Image Scanner
User Manual
Handheld Bluetooth 2D Imager Scanner OPN-3200n This manual provides specifications for the OPN3200n handheld Bluetooth 2D imager scanner. Specifications Manual OPN-3200n Specifications Manual All information subject to change without notice. Document History Model Number: OPN-3200n Specification Number: SS14022 Edition: 1st Original Spec Number: SS14020 Date: 2014-10-15 Copyright 2014 Opticon. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon. Limited Warranty and Disclaimers PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. Serial Number A serial number appears on all Opticon products. This official registration number is directly related to the device purchased. Do not remove the serial number from your Opticon device. Removing the serial number voids the warranty. Warranty Unless otherwise agreed in a written contract, all Opticon products are warranted against defects in materials and workmanship for two years after purchase. Opticon will repair or, at its option, replace products that are defective in materials or workmanship with proper use during the warranty period. Opticon is not liable for damages caused by modifications made by a customer. In such cases, standard repair charges will apply. If a product is returned under warranty and no defect is found, standard repair charges will apply. Opticon assumes no liability for any direct, indirect, consequential or incidental damages arising out of use or inability to use both the hardware and software, even if Opticon has been informed about the possibility of such damages. Packaging The packing materials are recyclable. We recommend that you save all packing material to use should you need to transport your scanner or send it for service. Damage caused by improper packaging during shipment is not covered by the warranty. Trademarks Trademarks used are the property of their respective owners. Opticon Inc. and Opticon Sensors Europe B.V. are wholly owned subsidiaries of OPTOELECTRONICS Co., Ltd., 12-17, Tsukagoshi 4-chome, Warabi-shi, Saitama, Japan 335-0002. TEL +81-(0) 48-446-1183; FAX +81-(0) 48446-1184 SUPPORT USA Europe Phone: 800-636-0090 Email: support@opticonusa.com Email: support@opticon.com Web: www.opticonusa.com Web: www.opticon.com OPN-3200n Specifications Manual Revision History Specification No. Product name Edition First : SS14022 : OPN-3200n Date 2014/10/15 Page Section Description of Changes Initial release OPN-3200n Specifications Manual Contents 1. Abstract ............................................................................................................................................. 1 2. Overview............................................................................................................................................ 1 3. Basic Specifications......................................................................................................................... 2 4. Detailed View .................................................................................................................................... 5 5. Electrical Specifications .................................................................................................................. 6 5.1. Current Consumption................................................................................................................ 6 5.2. Operating Time and Charging Time ......................................................................................... 6 6. Interface Specifications ................................................................................................................... 6 6.1. Bluetooth ................................................................................................................................... 6 7. Optical Specifications ...................................................................................................................... 7 7.1. Basic Optical Specifications...................................................................................................... 7 7.2. Aiming Pattern .......................................................................................................................... 8 7.3. Imaging Range.......................................................................................................................... 8 8. Technical Specifications.................................................................................................................. 9 8.1. Bar Code Test Sample............................................................................................................ 10 8.2. Scan Area and Depth of Field................................................................................................. 11 8.3. Printed Contrast Signal (PCS) ................................................................................................ 12 8.4. Minimum Resolution ............................................................................................................... 12 8.5. Wide Bar Code........................................................................................................................ 12 8.6. Pitch, Skew and Tilt ................................................................................................................ 13 8.7. Curvature ................................................................................................................................ 13 8.8. Auto Trigger ............................................................................................................................ 14 8.8.1. Stand Detection ............................................................................................................. 14 8.8.2. Auto Trigger Operation.................................................................................................. 14 8.8.3. Motion Tolerance........................................................................................................... 15 9. Environmental Specifications ....................................................................................................... 16 9.1. Temperature............................................................................................................................ 16 9.2. Humidity .................................................................................................................................. 16 9.3. Ambient Light Immunity .......................................................................................................... 16 9.4. Dust and Drip Proof ................................................................................................................ 16 9.5. Vibration Strength (without packing)....................................................................................... 16 9.6. Vibration Strength (in individual packing) ............................................................................... 17 9.7. Drop Impact Strength (without packaging) ............................................................................. 17 9.8. Drop Impact Strength (in individual packaging) ...................................................................... 17 9.9. Electrostatic Discharge (ESD) Immunity................................................................................. 17 10. Regulatory Compliance ............................................................................................................... 18 10.1. LED Safety ............................................................................................................................ 18 OPN-3200n Specifications Manual 10.2. Product Safety ...................................................................................................................... 18 10.3. EMC ...................................................................................................................................... 18 10.4. Others ................................................................................................................................... 19 11. RoHS .............................................................................................................................................. 19 12. Reliability....................................................................................................................................... 19 13. Precautions ................................................................................................................................... 19 13.1. Handling ................................................................................................................................ 19 13.2. Radio Law ............................................................................................................................. 20 13.3. Bluetooth ............................................................................................................................... 20 13.4. Frequency Baud.................................................................................................................... 20 14. Product Labels.............................................................................................................................. 21 15. Packaging Specifications ............................................................................................................ 22 15.1. Individual Packaging ............................................................................................................. 22 15.2. Collective Packaging............................................................................................................. 23 16. Physical Features ......................................................................................................................... 24 16.1. Dimensions ........................................................................................................................... 24 16.2. Weight ................................................................................................................................... 24 16.3. Mechanical Drawing.............................................................................................................. 24 17. Supported Symbologies .............................................................................................................. 25 17.1. Default Setting ...................................................................................................................... 25 17.2. Supported Symbologies........................................................................................................ 25 17.2.1. 1D Bar Codes .............................................................................................................. 25 17.2.2. GS1 Databar, Composite Code................................................................................... 26 17.2.3. 2D Codes..................................................................................................................... 26 OPN-3200n Specifications Manual 1. Abstract This manual provides specifications for the OPN-3200n handheld Bluetooth 2D imager scanner. 2. Overview The OPN-3200n is a handheld 2D imager scanner that enables high speed scanning of standard linear (1D) and 2D symbologies. The scanned data is output via Bluetooth. ・ All bar code data scanned is transmitted to a host device through the Bluetooth interface. ・ The scanner can work with many Bluetooth-enabled host devices, such as PCs, tablet PCs and smart phones. ・ Bluetooth SPP (Serial Port Profile) and HID (Human Interface Device Profile) are implemented. ・ The scanner can read bar codes from LCD screens. ・ A single green LED aiming line toward a target bar code can help the users find the appropriate scanning position. ・ Special antimicrobial treatment is applied to the chassis, and alcohol can be used to wipe the scanner clean (except for the scanning window and the logo panel). ・ The power source is 3.7 V 1100 mAh (typ.) lithium-ion battery. ・ A dedicated charging cradle CHG-3201 is supplied for recharging and easy storage of the scanner. OPN-3200n Specifications Manual 3. Basic Specifications Item Specification Control Section Input Section Indicator CPU 32 bit CISC / 96 MHz FROM 512 Kbyte + 32 Kbyte SRAM 96 Kbyte FROM (storage) 1 Mbyte Key type 1 key: trigger LED 2 colors (red, green) and 1 color (blue) Buzzer Loudness (3-level) / tone adjustable Interface Bluetooth For data area only Frequency 2402 ~ 2480 MHz Specification Bluetooth Ver 2.1 compliant Communication distance 10 m It may be shorter depending on usage environments Output level Class 2 Max output 4 dBm Profile SPP / HID Optical Section Scan method WVGA (0.36 million-pixel) CMOS area sensor Light source for illumination 2 red LEDs Light source for aiming 1 green LED Effective pixels 0.36 million pixels (H: 752 x V: 480) Horizontal: about 40.6° Vertical: about 26.4° UPC-A, UPC-A Add-on, UPC-E, UPC-E Addon, EAN-13, EAN-13 Add-on, EAN-8, EAN-8 Add-on, JAN-8, JAN-13, Code 39, Tri-Optic, NW-7, Industrial 2 of 5, Interleaved 2 of 5, SCode, IATA, Code 93, Code 128, MSI/Plessey, UK/Plessey, TELEPEN, Code 11, Matrix 2 of 5, Chinese Post Matrix 2 of 5, Korean Postal Authority code, Intelligent Mail Barcode, POSTNET, JPN View angle Symbologies Supported 1D Symbologies Minimum resolution Curvature Wide bar code Motion Tolerance Code 39 Depth of Field Code 128 UPC Note Code 39 : 0.127 mm Refer to Chapter 17. for details PCS 0.9 R ≥ 16 mm (10-digit 0.15 mm Codabar) R ≥ 20 mm (12-digit UPC) 100 mm wide 0.2 mm resolution Code 39 (DOF 115 mm) is readable: UPC 100% moving at 2m/sec (DOF 80 mm) is readable: Resolution (0.127) 60 ~ 95 Resolution (0.254) 45 ~ 185 Resolution (0.508) 50 ~ 250 Resolution (0.20) 65 ~ 150 Resolution (0.33) 45 ~ 175 Frame rate: 60 fps PCS 0.9 OPN-3200n Specifications Manual Item Specification GS1/Composite Symbologies Minimum resolution Symbologies Supported 2D Symbologies Minimum resolution (mm) PDF417 Depth of field (mm) QR Code DataMatrix GS1 DataBar, GS1 DataBar Limited, GS1 DataBar Expanded, Composite GS1 DataBar, Composite GS1-128, Composite EAN, Composite UPC GS1 DataBar : 0.169 mm Composite Code : 0.169 mm PDF417, MicroPDF417, Codablock F, QR Code, MicroQR Code, Data Matrix (ECC 0 140 / ECC 200), MaxiCode (Modes 2 to 5), Aztec Code, Aztec Runes, Chinese-sensible code, PLANET,Netherlands KIX,UK Postal, Australian Postal PDF417 : 0.169 mm QR Code : 0.212 mm DataMatrix : 0.212 mm Resolution (0.169) 55 ~ 105 Resolution (0.254) 35 ~ 155 Resolution (0.212) 70 ~ 95 Resolution (0.381) 35 ~ 165 Resolution (0.254) 65 ~ 120 Note GS1 DataBar: formerly called “RSS” Refer to Chapter 17. for details Disable Code 128 when Codablock F is enabled. Refer to Chapter 17. for details PCS 0.9 PCS 0.9 Pitch : ±50° Common Scan angle Skew : ±50° Tilt : ±180° MRD 32% or more Power Section Minimum PCS 0.3 or more Main battery Lithium-ion 1100 mAh (typ.) Charge the battery before initial use Up-time 24 hours or more *1 Operating (charging) voltage 5.0 ~ 6.5V Current consumption Charging Less than 1 A Operating 0 ~ 50°C Storage -20 ~ 60°C Operating 20 ~ 85% Storage 20 ~ 85% Fluorescent 10,000 lx or less Sunlight 100,000 lx or less Temperature Environmental Specifications Humidity Ambient light immunity Vibration Drop Dust and drip proof Charging with charger No condensing No frost UPC 100%, optical axis angle 75°, distance 100 mm 10 Hz ~ 100 Hz, acceleration of 19.6 m/s2, 60 minutes per cycle, repeat once in each X, Y and Z-direction Drop the scanner 30 times (6 faces x 5) from the height of 150 cm onto a concrete floor IP42 equivalent *1: When a bar code is read twice every 10 seconds at room temperature in a const Bluetooth connection (SPP master mode). OPN-3200n Specifications Manual Item Specification LED safety IEC 62471-1:2006 Exempt_Group Regulatory Compliance EN60950-1:2005 IEC60950-1:2006 EN 55022:2010 EN 301 489-1 V1.9.2 EN 301 489-17 V2.1.1 EN 300 328 V1.8.1 FCC Part 15 Subpart C, Subpart B ClassB VCCI Class B Bluetooth logo certification CE Marking Certification for Construction Design of Specified Radio Equipment Product safety EMC Other Immunity Test ESD No distraction Air discharge (direct): ±15 kV No malfunction Contact discharge (direct / indirect): ±6 kV Air discharge (direct): ±8 kV Physical Features Dimensions 113 × 56 × 132 (WDH mm) Weight Approx. 130 g Note Peak Wavelength 624 nm For residential, commercial and lightindustrial environments Conditions: IEC61000-4-2 compliant Excluding accessories OPN-3200n Specifications Manual 4. Detailed View Figure 1: Detailed View of OPN-3200n No Name Description Trigger Key A key to read bar codes Scan Window LED illumination is emitted from this window to read bar codes. Status LED The operating statuses, such as bar code reading, Bluetooth connection and warning, are indicated by different colors. Buzzer Holes A sound from a built-in buzzer comes out through these holes. Charging terminals Charging pins connected to the dedicated charging cradle CHG-3201 OPN-3200n Specifications Manual 5. Electrical Specifications 5.1. Current Consumption Standby Sleep Item Specification 15 mA or less 1 mA or less Operating 330 mA or less Measurement condition Power voltage 3.7 V at 25 °C Note With wireless connection Reading, communications, LED activated 5.2. Operating Time and Charging Time Item Sleep Battery Standby duration Reading Charging time Specification 200 hours or more Approx. 72 hours Approx. 24 hours Approx. 3 hours Note With wireless connection 1 scan / 5 secs with wireless connection With AC adaptor power supply * The above specifications may not be met when the battery pack has been deteriorated. 6. Interface Specifications 6.1. Bluetooth Frequency : 2402 ~ 2480 MHz Specification : Bluetooth Ver 2.1 compliant Communication distance : 10 m Output level : Class 2 (max 4 dBm) Implemented profile : SPP / HID Communication configuration : 1 to 1 Operating mode in communication : Master / Slave mode Security mode : Authentication supported Encryption : Encryption supported OPN-3200n Specifications Manual 7. Optical Specifications 7.1. Basic Optical Specifications Item Characteristics Scan method CMOS area sensor (white / black) Effective pixels (Column) × (Row) 752 × 480 dots Image capture speed (*1) Frame rate 60 fps Focal distance Distance from the front edge of scanner 124.8 mm Horizontal Approx. 40.6° Vertical Approx. 26.4° Red LED Peak wavelength 617 nm Directivity angle: 2Φ 1/2 (*2) 60° Maximum radiation output (*3) 15000 mcd Green LED Peak wavelength 528 nm Maximum radiation output (*4) 18700 mcd View angle Light source for illumination (LED × 2) Light source for aiming (LED × 1) *1 *2 60° is the data that the LED radiant intensity is reduced by half from the center of optical axis, which is The fastest seed of image capture *3, *4 reference value from the LED datasheet. Reference value based on the datasheet (25°C, IF = 140 mA ). OPN-3200n Specifications Manual 7.2. Aiming Pattern The aiming is used for the following purpose: 1. Light source to indicate the appropriate reading range 2. Light source for auto trigger opearation The aiming specifications are as follows: ・ An optical axis of imaging field of view and the center of horizontal aiming width coincide at a distance of L=65±20 mm from the front edge of the scanner. ・ The horizontal aiming width to the horizontal width of imaging filed of view at a distance of L=65 mm is 80%±10%. Figure 2: Aiming Pattern and Imaging Range 7.3. Imaging Range The range is ±5% from the following values. L: Distance from the front edge of scanner [mm] 60 80 100 120 140 160 H: Horizontal imaging range [mm] 66 82 97 111 125 136 V: Vertical imaging range [mm] 42 52 62 72 82 93 OPN-3200n Specifications Manual 8. Technical Specifications Code reading is performed by positioning the aiming light over the center of a code. The conditions for technical specifications are as follows unless otherwise specified in each section.Temperature and humidity Ambient light Angles Curvature Power supply voltage PCS (1D and 2D) Scanning Test Bar code test sample (1D and 2D) : Room temperature, room humidity : 100 ~ 200 lx : Pitch: α = 0°, Skew: β = 15°, Tilt: γ = 0° :R=∞ : 5.0 V : 0.9 or higher : 1 read in 0.5 sec or less. Accept the performance with 70% or more success rate for 10 readings. : Refer to Section 8.1. for details. 1D codes: GS1 Databar, Stacked codes, 2D codes: OPTOELECTRONICS test samples Labels printed by a dedicated printer for bar code OPN-3200n Specifications Manual 8.1. Bar Code Test Sample 1D Bar Codes Resolution 0.127 mm 0.20 mm 0.254 mm 0.508 mm Symbology PCS Size (mm) 32 × 10 100 × 10 32.5 × 12 36 × 25 No. of Digits 15 31 Code 39 0.9
Resolution 0.20 mm Symbology Code 128 PCS 0.9 Size (mm) 42 × 10 No. of Digits 16
Resolution 0.330 mm Symbology 12-digit UPC PCS 0.9/0.3 Size (mm) 31.5 × 25.0 No. of Digits 12 Resolution 0.150 mm Symbology Codabar (NW-7) PCS 0.9 Size (mm) 20 × 10 No. of Digits 10 Symbology Limited Limited-Composite PCS 0.9 0.9 Size (mm) 12 × 1.5 12 × 3.0 No. of Digits 14 26 Error Correction PCS No. of Character Level-3 0.9 Size (mm) 23 × 10 35 × 15 Error Correction PCS No. of Character 0.9 Size (mm) 6×6 11 × 11 Model PCS No. of Character ECC200 0.9 Size (mm) 5×5 GS1 Databar/Composite Resolution 0.169 mm 0.169 mm 2D Codes Resolution 0.169 mm 0.254 mm Resolution 0.212 mm 0.381 mm Resolution 0.212 mm 0.254 mm * The size is outline dimensions excluding the quiet zones. 10 6×6 58 44 40 OPN-3200n Specifications Manual 8.2. Scan Area and Depth of Field The scan area is within the arc centered on the scan origin as shown in each resolution, which is measured from the front edge of the scanner. 100 50 200 150 300 250 Resolution 0.127 60 Code 39 95 Resolution 0.254 45 Resolution 0.508 50 Code 128 100% UPC PDF417 185 Resolution 0.20 65 Resolution 0.33 45 55 Resolution 0.169 150 175 105 . 0.254 Resolution 35 250 155 Resolution 0.212 QR Code 70 95 Resolution 0.381 35 165 Resolution 0.254 Data Matrix 65 120 Figure 3: Scan Area and Depth of Field 11 [Unit: mm] OPN-3200n Specifications Manual 8.3. Printed Contrast Signal (PCS) 0.3 or higher MRD Distance Bar code : 32% and higher (70% or higher reflectivity of space and quiet zone) : 125 mm from the front edge of the scanner : UPC (resolution 0.33 mm, PCS 0.3) specified in Section 8.1. MRD = Minimum reflectance of white space - Maximum reflectance of black bar PCS = Reflectance of white spece - Reflectance of black bar Reflectance of white space * Be sure to keep the optical window clean without dirt or scratches, or it may have a bad effect on the reading characteristics. 8.4. Minimum Resolution 1D bar code GS1 Databar Stacked code 2D code : 0.127 mm (Code 39 specified in Section 8.1.) : 0.169 mm (GS1 Databar Limited specified in Section 8.1.) : 0.169 mm (PDF417, GS1 Databar Limited Composite specified in Section 8.1.) : 0.212 mm (QR Code, Data Matrix specified in Section 8.1.) Bar code Distance Angle Curvature : Above codes specified in Section 8.1. : 95 mm from the front edge of the scanner : α = 0°, β = + 15°, γ = 0° :R=∞ 8.5. Wide Bar Code Code 39 with width of 100 mm and resolution of 0.2 mm can be read Bar code Distance Angle Curvature : Code 39 (resolution 0.20 mm, PCS 0.9) specified in Section 8.1. : 155 mm from the front edge of the scanner : α = 0°, β = +15°, γ = 0° :R=∞ Figure 4: Wide Bar Code 12 OPN-3200n Specifications Manual 8.6. Pitch, Skew and Tilt Pitch Skew Tilt Bar code Distance Curvature Angle : α = ±50° : β = ±50° : γ = ±180° : UPC (resolution 0.33 mm) specified in Chapter 8.1 : 125 mm from the front edge of the scanner :R=∞ : Pitch β = +15°, γ = 0° Skew, Dead zone α = 0°, γ = 0° Tilt α = 0°, β = +15° α β γ Figure 5: Pitch, Skew and Tilt 8.7. Curvature 0.33 mm 12-digit UPC 0.15 mm 10-digit Codabar (NW-7) Bar code Distance Angle : R ≥ 20 mm : R ≥ 16 mm : UPC (0.33 mm) and Codabar (0.15 mm) specified in Section 8.1. : 105 mm from the front edge of the scanner : α = 0°, β = +15°, γ = 0° Bar code Figure 6: Curvature * The reading characteristics may deteriorate due to the specular reflection of LED illumination when the reflectivity is high. 13 OPN-3200n Specifications Manual 8.8. Auto Trigger When the scanner is placed in a dedicated stand (sold separately) which contains a magnet, it can detect this magnet and enters auto trigger mode. The scanner starts scanning automatically when it detects a change in brightness that occurs when a bar code label is presented in front of it. 8.8.1. Stand Detection “Stand detection - Auto trigger Flow” Is Stand Detection mode “*4” enabled? No Yes Is the scanner in the stand? No Yes Manual Trigger Auto Trigger Figure 7: Stand Detection Flow * The dedicated stand is an optional accessory that can be purchased separately. * The stand detection mode is disabled by default. It must be enabled to be used. 8.8.2. Auto Trigger Operation Trigger should be enabled when a gray-colored paper is presented in front of a background black-colored paper. Trigger should also be enabled when the black-colored paper is presented in front of the background gray-colored paper. Paper Ambient light Moving speed of paper Temperature / Humidity : Black paper from Glory: Black 010010016 : Gray paper from Glory: Silver-gray 010010016 : 500 ~ 1000 lx : 2 m/sec or slower : Room temperature / room humidity Background Paper Detection range Figure 8: Auto Trigger 14 OPN-3200n Specifications Manual 8.8.3. Motion Tolerance 100% UPC bar codes moving at 2m/s can be read. Temperature / Humidity Ambient light Distance PCS Bar code : Room temperature / room humidity : 500 ~ 1000 lx : 125 mm from the front edge of the scanner : 0.9 or higher : Refer to Section 8.1. Figure 9: Motion Tolerance * The reading characteristics may deteriorate due to the specular reflection of LED illumination when the reflectivity is high. 15 OPN-3200n Specifications Manual 9. Environmental Specifications 9.1. Temperature Scanning performance is guaranteed when the range of ambient temperature around the scanner is the following values: Operating temperature Storage temperature : 0 ~ 50 °C : -20 ~ 60°C 9.2. Humidity Scanning performance is guaranteed when the range of ambient humidity around the scanner is the following values: Operating humidity Storage humidity : 20 ~ 85% RH (no condensation, no frost) : 20 ~ 85% RH (no condensation, no frost) 9.3. Ambient Light Immunity Scanning performance is guaranteed when the range of illumination on a bar code surface is between zero and the following values: Incandescent light Fluorescent light Sunlight : 10,000 lx : 10,000 lx : 100,000 lx Bar code Distance Angle Curvature Power supply voltage : UPC (resolution 0.33 mm) specified in Section 8.1. : 125 mm from the front edge of the camera module : α = 0°, β =+15°, γ = 0° :R=∞ : 3.7 V * Be sure that the direct light or specular reflection from the light source does not enter the light receiving section of the scanner. 9.4. Dust and Drip Proof IEC IP42 equivalent Protection against solid objects: Level 4 equivalent Protected against solid objects greater than 1.0 mm Protection against liquids: Level 2 (JIS IPX2) equivalent Protected against dripping water from the vertical when tilted up to 15° * () is JIS drip-proof type. 9.5. Vibration Strength (without packing) There shall be no sign of malfunction after the following vibration test. Vibration test: Increase the frequency of the vibration from 10Hz to 100Hz at an accelerated velocity of 19.6m/s2 (2.0 G) for 30 minutes (60 minutes per cycle) in the non-operating state. Repeat this in each X, Y and Z direction. 16 OPN-3200n Specifications Manual 9.6. Vibration Strength (in individual packing) There shall be no sign of malfunction after the following vibration test. Vibration test: Increase the frequency of the vibration from 10Hz to 100Hz at an accelerated velocity of 19.6 m/s2 (2.0 G) for 30 minutes (60 minutes per cycle) in individually packaged state. Repeat this in each X, Y and Z direction. 9.7. Drop Impact Strength (without packaging) There shall be no sign of malfunction after the following drop test. Drop test: Drop the scanner 30 times in total (5 times at each 6 face) from a height of 150 cm onto a concrete floor as shown below. 150cm 150 cm Concret Figure 10: Drop Test 9.8. Drop Impact Strength (in individual packaging) There shall be no sign of malfunction after the following drop test. Drop test: Drop an individually packaged scanner 10 times in total, at any of 1 corner, 3 edges, and 6 faces, from a height of 150 cm onto a concrete floor. 9.9. Electrostatic Discharge (ESD) Immunity Contact discharge Aerial discharge : ±6 kV max (direct or indirect discharge, no malfunction) : ±8 kV max (no malfunction) ±15 kV max (no distraction) Measurement environment Discharge resistance Charging capacitor : Testing method compliant with IEC-61000-4-2. : 330 Ω : 150 pF 17 OPN-3200n Specifications Manual 10. Regulatory Compliance 10.1. LED Safety IIEC 62471-1:2006 Exempt_Group 10.2. Product Safety EN60950-1:2005 IEC60950-1:2006 10.3. EMC R&TTE Directive ・EN 55022:2010 ・EN 301 489-1 V1.9.2 ・EN 301 489-17 V2.1.1 ・EN 300 328 V1.8.1 FCC Part 15 Subpart B Class B Federal Communications Commission Notices This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Harmful Interference Notice This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment or devices • Connect the equipment to an outlet other than the receiver's • Consult a dealer or an experienced radio/TV technician for assistance Changes or modifications to this equipment that have not been approved by Ruckus Wireless may void the user's authority to operate this equipment. RF Exposure Information This product complies with FCC radiation exposure limits set forth an uncontrolled environment. VCCI Class B This is a Class B product, to be used in a domestic environment, based on the Technical Requirement of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. 18 OPN-3200n Specifications Manual 10.4. Others ・Bluetooth logo certification ・Certification for Construction Design of Specified Radio Equipment ・Classification of Specified Radio Equipment ・Model Name ・Certificate Number Article 2 Paragraph 1, Item 19 Low power data communication system in 2.4 GHz band OPA-26X1 201-125603 11. RoHS The OPN-3200n is compliant with RoHS. RoHS: The restriction of the use of certain hazardous substances in electrical and electronic equipment, 2011/65/EU 12. Reliability MTBF (Mean Time Between Failures) 10,000 hours 13. Precautions 13.1. Handling Handle this product carefully. Do not deliberately subject it to any of the following. (1) Shock: ・Do not drop this product from a height greater than specified in this manual. ・Do not place this product under or between any heavy items. ・Do not swing the cable around. (2) Temperature Conditions: ・Do not use this product at temperatures outside the specified range. ・Do not pour boiling water on this product. ・Do not throw this product into a fire. (3) Foreign Materials: ・Do not immerse this product in water or other liquid. ・Do not expose this product to chemicals. (4) Others ・Do not disassemble this product. ・Do not use this product near a radio or a TV. It may cause reception problems. ・This product may be affected by a momentary voltage drop caused by lightning. 19 OPN-3200n Specifications Manual 13.2. Radio Law This product qualifies as specified radio equipment for radio stations of 2.4 GHz band data communication system and has obtained the Certification for Construction Design of Specified Radio Equipment. Therefore, radio station license is not required in Japan. The following activities are prohibited under the Radio Law: ・Remodeling and disassembly ・Peeling off the certificate label Do not use this equipment under the following environment, as radio interference may affect other device and end up with causing physical or material damage. ・Safety apparatus and medical device for human body protection ・Environment where is concerned to cause serious damage 13.3. Bluetooth ・This product supports Bluetooth wireless communication with other Bluetooth devices that have the same profile ・This product complies with Bluetooth standards; however, its communication performance with untested devices is not guaranteed. ・Bluetooth devices use the 2.4 GHz frequency band that is shared among other devices. It may affect the communication speed and distance between this product and the host device. ・The communication speed and distance vary depending on the interference and radio wave condition between this product and the host device. 13.4. Frequency Baud This product uses the 2.4 GHz frequency band. Read carefully the followings before using this product. In the frequency band of this product, scientific, medical and industrial devices including microwaves are used. Also other radio stations including local private radio station for mobile object identification requiring license for such as manufacturing lines at factories, specific power-saving radio station requiring no license and amateur radio station are managed. 1. Make sure that “other radio stations” are not managed in the frequency band 2.4 GHz before using this product. 2. In case that radio interference occurs between this product and “other radio stations,” change the service space immediately, or stop transmitting radio wave to avoid the interference. 3. If you have any questions or troubles, please contact our sales office. 20 OPN-3200n Specifications Manual 14. Product Labels The product labels are affixed to the scanner as shown below. Product label Logo label Figure 11: Product Labels Product label Shows the product name, serial number, and month and year of manufacture. Logo label Shows the standards-compliant languages and logos. 21 OPN-3200n Specifications Manual 15. Packaging Specifications 15.1. Individual Packaging Assembled package size: 165 × 110 × 82 (WDH mm) Figure 12: Individual Packaging 22 OPN-3200n Specifications Manual 15.2. Collective Packaging Assembled package size : 585 × 520 × 200 (WDH mm) Figure 13: Collective Packaging * ‘Ro mark’ on the boxes for the product indicates that the product is RoHS compliant declared by Optoelectronics Co., Ltd. 23 OPN-3200n Specifications Manual 16. Physical Features 16.1. Dimensions 56 × 113 × 132 (WDH mm / excluding protruding portion) 16.2. Weight Approx. 130 g (excluding accessories) 16.3. Mechanical Drawing (113) (56) (132) Figure 14: Mechanical Drawing 24 OPN-3200n Specifications Manual 17. Supported Symbologies 17.1. Default Setting The scanner is set to default settings by reading the following menu label. Default @MENU_OPTO@ZZ@SO@ZZ@OTPO_UNEM@ 17.2. Supported Symbologies 17.2.1. 1D Bar Codes Code type UPC UPC Add-on 2 UPC Add-on 5 EAN (JAN) EAN Add-on 2 EAN Add-on 5 EAN-13 EAN-13 Add-on 2 EAN-13 Add-on 5 EAN-8 EAN-8 Add-on 2 EAN-8 Add-on 5 Code 39 Default Minimum length ○ ○ Note ○ ○ ○ Not transmit ST/SP Tri-Optic ○ Not transmit ST/SP Codabar (NW7) ○ Not transmit ST/SP Industrial 2 of 5 ○ Interleaved 2of 5 ○ S-Code Code 128 ○ Code 93 ○ IATA ○ MSI/Plessey UK/Plessey TELEPEN Code 11 Matrix 2 of 5 Chinese Post Matrix 2 of 5 Korean Postal Authority Intelligent Mail Barcode POSTNET JPN (Customer Barcode) 25 GS1 conversion (setting required) OPN-3200n Specifications Manual 17.2.2. GS1 Databar, Composite Code Code type GS1 DataBar ・GS1 DataBar Omnidirectional ・GS1 DataBar Truncated ・GS1 DataBar Stacked ・GS1 DataBar Stacked Omnidirectional GS1 DataBar Limited GS1 DataBar Expanded ・GS1 DataBar Expanded ・GS1 DataBar Expanded Stacked Composite GS1 DataBar ・CC-A ・CC-B ・Limited CC-A ・Limited CC-B ・Expanded CC-A ・Expanded CC-B Composite GS1-128 ・CC-A ・CC-B ・CC-C Composite EAN ・EAN-13 CC-A ・EAN-13 CC-B ・EAN-8 CC-A ・EAN-8 CC-B Composite UPC ・UPC-A CC-A ・UPC-A CC-B ・UPC-E CC-A ・UPC-E CC-B Default Note ○ GS1 conversion (setting required) ○ ○ ○ GS1 conversion (setting required) GS1 conversion (setting required) GS1 conversion (setting required) GS1 conversion (setting required) 17.2.3. 2D Codes Code type Default ○ PDF417 Note Micro PDF417 Codablock F QR Code ○ Micro QR ○ Data Matrix (ECC 200) ○ GS1 conversion (setting required) GS1 conversion (setting required) Data Matrix (ECC 000-140) Aztec Code ○ Aztec Runes Chinese-sensible code Maxi Code PLANET Netherlands KIX UK Postal Australian Postal * The supported symbologies vary depending on specifications for the application to be loaded. 26
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Producer : Acrobat Distiller 8.0.0 (Windows) Creator Tool : PScript5.dll Version 5.2 Modify Date : 2014:10:17 15:50:16+08:00 Create Date : 2014:10:17 10:19:11+09:00 Metadata Date : 2014:10:17 15:50:16+08:00 Format : application/pdf Title : Microsoft Word - SS14022_OPN-3200n_Master Specification_ENG1.doc Creator : tyamazaki0304 Document ID : uuid:9347214f-6ba4-4318-a53c-8b3a7c7f1b05 Instance ID : uuid:ed0605db-8cdd-4163-94c9-3e8c5bb98692 Page Count : 31 Author : tyamazaki0304EXIF Metadata provided by EXIF.tools