ORION ELECTRIC M2J4A DVD / VCR TV Interface Device User Manual 2J40101A Cover

ORION ELECTRIC CO., LTD. DVD / VCR TV Interface Device 2J40101A Cover

Contents

User Manual 1

Hi-Fi VCR & DVD VIDEO RECORDERD-VR5SUOWNER’S MANUAL22434495363IntroductionVarious settingsDisc playbackTape playbackRecordingEditing the disc©2006 Toshiba Corporation7882DubbingAdditional informationThis device does not tape-record copy protected DVD Video Discs.DIGITAL VIDEO 2J40101A Cover 3/4/06, 10:42 AM1DRAFT
Introduction2WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not expose this appliance to rainor moisture.CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH ANEXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CANBE FULLY INSERTED TO PREVENT BLADE EXPOSURE.FCC NOTICE:This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interfer-ence by one or more of the following measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.-Consult the dealer or an experienced radio/TV technician for help.CAUTION:Changes or modifications not expressly approved by the partly responsible for compliance with theFCC Rules could void the user's authority to operate this equipment.CAUTION: THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM.TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS USER'S GUIDE CARE-FULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTE-NANCE, CONTACT AN AUTHORIZED SERVICE LOCATION.USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHERTHAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLO-SURE. VISIBLE LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED.DO NOT STARE INTO BEAM.The lightning flash with arrowhead symbol, within anequilateral triangle is intended to alert the user to thepresence of uninsulated dangerous voltage within theproduct's enclosure that may be of sufficient magnitude toconstitute a risk of electric shock to persons.The exclamation point within an equilateral triangle isintended to alert the user to the presence of importantoperating and maintenance (servicing) instructions in theliterature accompanying the appliance.Location of the required MarkingThe rating sheet and the safety caution are on the rear of the unit.CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMANCESTANDARDS, 21 CFR SUBCHAPTER J.SAFTY PRECAUTIONSRISK OF ELECTRIC SHOCKDO NOT OPENCAUTIONCAUTION:TO REDUCE THE RISK OF ELECTRICSHOCK, DO NOT REMOVE COVER(OR BACK). NO USER-SERVICEABLEPARTS INSIDE. REFER SERVICING TOQUALIFIED SERVICE PERSONNEL. 2J40101A P02-07 3/4/06, 10:42 AM2
Introduction31. READ INSTRUCTIONSAll the safety and operating instructions should be read before the unit is operated.2. RETAIN INSTRUCTIONSThe safety and operating instructions should be retained for future reference.3. HEED WARNINGSAll warnings on the unit and in the operating instructions should be adhered to.4. FOLLOW INSTRUCTIONSAll operating and use instructions should be followed.5. CLEANINGUnplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.Use a soft dry cloth for cleaning the exterior cabinet only.6. ATTACHMENTSThe manufacturer of this unit does not make any recommendations for attachments, as they may causehazards.7. WATER AND MOISTUREDo not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wetbasement, or near a swimming pool.8. ACCESSORIESDo not place this unit on an unstable cart, stand, tripod, bracket, or table.The unit may fall, causing serious injury, and serious damage to the unit.8A. An appliance and cart combination should be moved with care. Quick stops,excessive force, and uneven surfaces may cause the appliance and cartcombination to overturn.9. VENTILATIONSlots and openings in the cabinet back or bottom are provided for ventilation,to ensure reliable operation of the unit, and to protect it from overheating.These openings must not be blocked or covered. The openings should never be blocked by placing the uniton a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heatsource. This unit should not be placed in a built-in installation such as a bookcase or rack unless properventilation is provided and/or the manufacturer’s instructions have been adhered to.10. POWER SOURCEThis unit should be operated only from the type of power source indicated on the rating plate. If you are notsure of the type of power supply to your home, consult your appliance dealer or local power company.11. GROUNDING OR POLARIZATIONThis unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than theother). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insertthe plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician toreplace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.12. POWER-CORD PROTECTIONPower-supply cords should be routed so that they are not likely to be walked on or pinched by items placedupon or against them, paying particular attention to cords at plugs, convenience receptacles, and the pointwhere they exit from the appliance.S3125APORTABLE CART WARNING(symbol provided by RETAC)IMPORTANT SAFEGUARDS 2J40101A P02-07 3/4/06, 10:42 AM3
Introduction4IMPORTANT SAFEGUARDS13. LIGHTNINGTo protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to theunit due to lightning and power line surges.14. POWER LINESAn outside antenna system should not be located in the vicinity of overhead power lines or other electriclight or power circuits, or where it can fall onto or against such power lines or circuits. When installing anoutside antenna system, extreme care should be taken to keep from touching such power lines or circuits,as contact with them might be fatal.15. OVERLOADINGDo not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.16. OBJECT AND LIQUID ENTRYDo not push objects through any openings in this unit, as they may touch dangerous voltage points or shortout parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.17. OUTDOOR ANTENNA GROUNDINGIf an outside antenna or cable system is connected to the unit, be sure the antenna or cable system isgrounded to provide some protection against voltage surges and built-up static charges, Section 810 of theNational Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mastand supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of groundingconductors, location of antenna discharge unit, connection to grounding electrodes, and requirements forthe grounding electrode.EXAMPLE OF ANTENNA GROUNDING AS PER THENATIONAL ELECTRICAL CODEANTENNADISCHARGE UNIT(NEC SECTION 810-20)ANTENNA LEAD IN WIREGROUNDING CONDUCTORS(NEC SECTION 810-21)GROUND CLAMPSPOWER SERVICE GROUNDINGELECTRODE SYSTEM(NEC ART 250, PART H)GROUND CLAMPELECTRIC SERVICEEQUIPMENTNEC-NATIONAL ELECTRICAL CODES2898A18. SERVICINGDo not attempt to service this unit yourself as opening or removing covers may expose you to dangerousvoltage or other hazards. Refer all servicing to qualified service personnel.For example:a. When the power-supply cord or plug is damaged.b. If liquid has been spilled, or objects have fallen into the unit.c. If the unit has been exposed to rain or water.d.If the unit does not operate normally by following the operating instructions. Adjust only those controls thatare covered by the operating instructions, as an improper adjustment of other controls may result in damageand will often require extensive work by a qualified technician to restore the unit to its normal operation.e. If the unit has been dropped or the cabinet has been damaged.f . When the unit exhibits a distinct change in performance, this indicates a need for service. 2J40101A P02-07 3/4/06, 10:42 AM4
Introduction5CONDENSATIONMoisture will form in the operating section of the DVD/VCR if the unit is brought from cool surroundings into a warmroom or if the temperature of the room rises suddenly. When this happens, the DVD/VCR’s performance will beimpaired.To prevent this, let the DVD/VCR stand in its new surroundings for about an hour before switching it on, or makesure that the room temperature rises gradually.Condensation may also form during the summer if the DVD/VCR is exposed to the breeze from an air conditioner.In such cases, change the location of the DVD/VCR.* This product incorporates copyright protection technology that is protected by method claims of certain U.S.patents and other intellectual property rights owned by Macrovision Corporation and other rights owners.Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intendedfor home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation.Reverse engineering or disassembly is prohibited.Consumers should note that not all high definition television sets are fully compatible with this productand may cause artifacts to be displayed in the picture. In case of 525 progressive scan picture problems,it is recommended that the user switch the connection to the “STANDARD DEFINITION” output. If thereare questions regarding our TV set compatibility with this model 525p DVD player, please contact ourcustomer service center.* is a trademark of DVD Format/Logo Licensing Corporation.* DivX, DivX Certified, and associated logos are trademarks of DivX, Inc. and are used under license.* HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks ofHDMI licensing LLC.* Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks ofDolby Laboratories.* “DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.* Unauthorized recording of copyrighted television programs, films, video cassettes and other materials mayinfringe the rights of copyright owners and be contrary to copyright laws.* Certain audio features of this product manufactured under a license from Desper Products, Inc. Spatializer®,N-2-2™ and the circle-in-square device are trademarks owned by Desper Products, Inc.*Microsoft, Windows Media, and the Windows logo are either registered trademarks or trademarks of MicrosoftCorporation in the United States and/or other countries.19. REPLACEMENT PARTSWhen replacement parts are required, be sure the service technician uses replacement parts specified bythe manufacturer or those that have the same characteristics as the original part.Unauthorized substitutions may result in fire, electric shock or other hazards.20. SAFETY CHECKUpon completion of any service or repairs to this unit, ask the service technician to perform safety checks todetermine that the unit is in proper operating condition.21. HEATThe product should be situated away from heat sources such as radiators, heat registers, stoves, or otherproducts (including amplifiers) that produce heat.22. DISC TRAYKeep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.23. CONNECTINGWhen you connect the product to other equipment, turn off the power and unplug all of the equipment fromthe wall outlet. Failure to do so may cause a product damage. Read the owner's manual of the other equip-ment carefully and follow the instructions when making any connections.24. LASER BEAMDo not look into the opening of the disc tray or ventilation opening of the product to see the source of thelaser beam. It may cause sight damage.25. DISCDo not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause seriouspersonal injury and product malfunction.26. NOTE TO CABLE TV SYSTEM INSTALLERThis reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the NEC thatprovides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con-nected to the grounding system of the building, as close to the point of cable entry as practical.IMPORTANT SAFEGUARDS 2J40101A P02-07 3/4/06, 10:42 AM5
Introduction6Introduction• SAFTY PRECAUTIONS ...................................... 2• IMPORTANT SAFEGUARDS .............................. 3• Contents ............................................................. 6• Features .............................................................. 8• Disc ..................................................................... 9Handling discs ................................................... 9Discs which can be played back ........................ 9Discs on which video can be recorded ............ 10DVD-RAM ........................................................ 10DVD-RW .......................................................... 10DVD-R .............................................................. 10Recording format ............................................. 10Disc playback in other players ......................... 11On Video CDs .................................................. 11• Parts and functions ......................................... 12Front ................................................................ 12Rear ................................................................. 12Display window ................................................ 13Remote control ................................................ 14Power Source .................................................. 15• Antenna connections ...................................... 16• Cable TV connections ...................................... 18• Connections with the TV or audio component ........................................................ 20• Auto clock setting ............................................ 23• Setting the video channel ............................... 23Various settings• SETUP MENU ................................................... 24Using the SETUP MENU ................................. 24• Setting the language........................................ 25OSD LANGUAGE ............................................ 25DVD MENU ...................................................... 25AUDIO .............................................................. 25SUBTITLE........................................................ 25• Setting the parental control ............................ 26Selecting parental control ................................ 26Temporarily cancelling parental control ........... 26• Setting the clock .............................................. 27CLOCK (manually)........................................... 27AUTO CLOCK .................................................. 27STANDARD TIME (Time zone) ........................ 27DAYLIGHT SAVING TIME ............................... 27• Setting the disc ................................................ 28REFORMAT ..................................................... 28NEW DISC FORMAT ....................................... 28FINALIZE ......................................................... 28PROTECT DISC .............................................. 29UNDO FINALIZE ............................................. 29DVD-RAM Physical Format.............................. 29• Other (SYSTEM SETUP) .................................. 29DIMMER (Brightness of the display window) ... 29DISPLAY/CALL (Turning the screen display“ON” or “OFF”) ................................................. 29Contents• Setting the screen ............................................ 30TV SCREEN .................................................... 30STILL MODE ................................................... 30LINE1 INPUT/LINE2 INPUT ............................ 30• Setting the image quality ................................ 31BRIGHTNESS ................................................. 31E.B.L. ............................................................... 31• Setting the audio .............................................. 31DRC ................................................................. 31VIRTUAL SURROUND (Spatializer N-2-2TM)... 31EXTERNAL AUDIO INPUT .............................. 31SAP (Second Audio Program) ......................... 32DOLBY DIGITAL OUTPUT .............................. 32• Setting the recording ....................................... 32INITIAL REC TO .............................................. 32INITIAL REC MODE ........................................ 32AUTO CHAPTER ............................................. 32INDEX PICTURE ............................................. 32BLACK LEVEL (REC) ...................................... 32• Setting the channel .......................................... 33TV/CABLE SELECT ........................................ 33AUTO CH MEMORY ........................................ 33ADD/DELETE (channels) ................................ 33• Setting other items .......................................... 33JPEG INTERVAL ............................................. 33DivX® VOD ........................................................ 33Disc playback• Playback procedure ......................................... 34• Playback by selecting a title ........................... 35• Checking media information ........................... 36• Special playback .............................................. 37Fast forward playback ...................................... 37Review playback .............................................. 37Still playback .................................................... 37Frame advance ................................................ 37Slow motion playback ...................................... 37Locating a chapter or track .............................. 37• Instant skip ....................................................... 38• Locating a specific scene ............................... 38• Repeat playback ............................................... 39Instant replay ................................................... 39A-B repeat playback......................................... 39Title, Chapter repeat playback ......................... 39• Title selection ................................................... 40• DVD menu ......................................................... 40• Changing angles .............................................. 41• Zooming ............................................................ 41• Karaoke playback ............................................ 41• Changing soundtrack language ..................... 42• Subtitles ............................................................ 42Tu r ning the subtitles On and Off ...................... 42Changing the subtitles language ..................... 42• To turn off the PBC (VIDEO CD Version 2.0) ... 42• Various operations on CD ............................... 43• MP3/WMA/JPEG/DivX® playback .................... 45 2J40101A P02-07 3/4/06, 10:42 AM6
Introduction7• Editing an original title .................................... 70Adding a chapter mark .................................... 70Combining chapters ......................................... 71Changing an original title name ....................... 72Erasing a scene (Edit title) ............................... 73Erasing an original title .................................... 74• Changing a disc name ..................................... 75Changing a disc name ..................................... 75Using the keyboard screen .............................. 76Dubbing• Dubbing a tape onto a disc ............................. 78• Dubbing a disc onto a tape ............................. 79• Dubbing using other equipment..................... 80Additional information• Glossary ........................................................... 82• Language code list .......................................... 84• Problems and troubleshooting ....................... 85• Video head cleaning ........................................ 86• Error/Warning message list ............................ 87• Specifications................................................... 88• Limited Warranty .............................................. 89Tape playback• Loading and unloading a cassette tape......... 49• Cassette tape playback ................................... 50• Special playback .............................................. 51Picture search .................................................. 51Still picture ....................................................... 51Slow motion ..................................................... 51Frame by frame picture .................................... 51Adjusting tracking condition ............................. 51Repeat playback .............................................. 51Instant skip....................................................... 51To display VCR operation status ...................... 51• ZERO RETURN function .................................. 52• Video index search system ............................. 52Recording• Read this before recording on disc ................ 53Types of disc .................................................... 53Recording modes............................................. 53Disc remaining time ......................................... 53Images that cannot be recorded ...................... 54• Recording a TV program ................................. 55• One-touch Timer Recording (OTR) ................. 57• Timer recording ................................................ 58• Chase playback ................................................ 61• Stereo recording and playback ....................... 62Editing the disc• Editing the disc ................................................ 63• Editing a playlist .............................................. 64Creating a playlist ............................................ 64Changing a title name ...................................... 65Erasing a scene (Edit title) ............................... 66Combining the title ........................................... 68Erasing a playlist .............................................. 69ContentsMedia markEach applicable media are indicated using the symbol shown below.: DVD-Video : DVD-R: DVD-RW in VR mode: Audio/Video CD and CD-R/CD-RW: DVD-RW in Video mode : Video tape: DVD-RAM 2J40101A P02-07 3/4/06, 10:42 AM7
Introduction8FeaturesPlayback functionTitle menuVideo CD/SVCD/MP3/WMA/JPEG/DivX® playbackVideo CD/SVCD/MP3/WMA/DivX® files can be playedback. Also, you can display JPEG files on the TV screenand enjoy them as a slide show.Progressive scanThis unit supports the progressive scanning system. Ifyour TV is equipped with component video input jackswhich support the progressive video input, you can enjoyhigh quality picture.Thumbnail image will not appear after finalizing inVideo mode.•Not only can you playback and record video tapes, butyou can also playback DVD discs or make recordingsusing DVD-RAM, DVD-RW or DVD-R discs with this unit.In addition, you can enjoy editing the programs yourecord.A realistic, powerful, Movie Theater soundWhen connected to Dolby Digital and DTS compliantdevices, you can enjoy realistic, powerful surroundsound.Playback the scene you want to see immediatelyAs DVD’s do not require rewinding like video tapes, youcan get to the scene you wish to watch immediately. Avariety of search functions allow you to find the sceneyou wish to watch.As thumbnail images are displayed in the title menu,you can find the title you want to play back quickly.Chase PlaybackYou can begin playback from the beginning of a programcurrently being recorded. You will find this function ofgreat advantage on long programs, as you do not haveto wait for the end of recording to begin playback.Recording functionTimer recordingThe timer recording system allows you to select thedate, time and channel and record the desired programs.Up to 12 timer programs within a month can be storedin this unit.One-touch Timer Recording (OTR)The One-touch Timer Recording feature provides asimple and convenient way to make a timed recording.Edit functionEditing recorded material without changingthe original titlesYou can create a playlist based on the original titles.The playlist won’t affect the original titles. If you erasethe playlist, the original titles remain. It is recommendedto create and edit the playlist to prevent important titlesfrom being erased accidentally.Chapter markYou can add (or delete) a chapter mark to (from) theoriginal title. This function is useful when searching forthe scene you wish to watch that you have marked withthe Chapter mark function.Erasing scenesYou can erase an unnecessary scene from the createdplaylist or the original titles.Combining titlesYou can combine several original titles or playlists to aseparate playlist.Dubbing functionDubbing a tape onto a disc or a disc onto atape•Dubbing cannot be carried out when attempting tocopy a “copy guarded” video tape or disc.With just this one unit, you can dub whatever you like,from video tape to disc, or from disc to video tape. 2J40101A P08-11 3/4/06, 10:43 AM8
Introduction9DiscHandling discsRemoving the Disc from its caseBe sure to hold the disc by its edges.Do not touch the surface of the disc.Take the disc carefully from its case.•Do not scratch the disc.•Do not get dirt on the surface of the disc.•Do not stick labels or adhesive tapes on the disc.•Do not drop or bend the disc.Storing discs•Store the disc in the case to avoid any risk ofscratches, dirt or damage.•Do not leave the disc exposed to direct sunlight orin hot or humid places.Cleaning discsWipe the disc with a clean, dry cloth from the centeroutward toward the edges.•Do not wipe the disc in a circular motion around thecenter.•Do not use liquid or aerosol cleaners.Region management informationThis unit is designed and manufactured to support theregion management information that is recorded on aDVD disc. If the region number written on the DVD discdoes not correspond to the region number of this unit,this unit cannot play that disc.•The region number of this unit is “1”.•The unit will play DVD-Video discs marked with la-bels containing “1” or “ALL”.Example: 1Operating DVD-Video•Some operations of DVD-Video may be prohibitedby the manufacturer, or some operation methods orfunctions of the DVD-Video may be different from thedescription in this manual.•If you attempt an operation that is prohibited by ei-ther the disc or the unit, a “ ” mark will appear on theTV monitor. For operations prohibited by the disc, seethe information that came with the disc.•When the menu screen or the operation guide ap-pears during disc playback, follow the displayed in-formation.Discs which cannot be played backThe discs listed below cannot be played back ingeneral. Even if one of these can be played back, itmay not be played back correctly. If a disc is playedback by mistake, extensively loud sounds may blow thespeakers or may damage the hearing of those inhearing range. Do not playback the discs listed below.CDG, Photo-CD, CD-ROM, CD-TEXT, CD-EXTRA,SACD, PD, CDV, DVD-ROM, DVD+R/RW,DVD audio, etc.The below DVD-Video may not be played back.•DVD-Video that do not have the region number “1” or“ALL”.•PAL or SECAM DVD-Video.•Prohibited or business-use DVD-Video.CD-R/CD-RWs cannot be played back for the fol-lowing reasons.•Compatibility of the disc and this unit.•Compatibility of the disc and the recorder used.•Unfinalized discs.Do not playback the following discs. Playback ofthese discs may cause a failure.•Discs on which paper, labels or stickers are affixed.•Discs that have sticky areas left by adhesive tape.•Special-shaped discs.*1When using cartridge-type DVD-RAM discs, it will be necessary toremove the disc from the cartridge.*2This unit is designed to playback music Compact Discs (CD) thatconform to the CD standard. CDs that contain (copy-restriction) sig-nals to protect copyrights cannot be played back.Discs which can be played backIn this unit, use only discs that meet the standard, suchas those bearing the below logo marks on the disc labelsurface. If you use a non-standard disc, we cannot guar-antee playback. Even if such a disc can be played back,we cannot guarantee the image or sound quality.The DVD logo is a registered trademark.Media type Logo markDVD-VideoDVD-RAM*1 Ver.2.0 Ver.2.1DVD-RWVer.1.0, Ver.1.1, Ver.1.2Ver.1.1 CPRM supportVer.1.2 CPRM supportDVD-R Ver.2.0, Ver.2.1Audio CD*2Video CDSVCDCD-R/CD-RWlDIGITAL VIDEONotes on DVDs and CDsBecause of problems and errors that can occur duringthe creation of DVD and CD Software and/or the manu-facture of DVD and CD discs, Toshiba cannot assurethat the DVD player will successfully play every disc bear-ing DVD and CD logos. If you happen to experience anydifficulty playing a DVD and/or CD disc on this DVD player,please contact Toshiba Customer Service. 2J40101A P08-11 3/4/06, 10:43 AM9
Introduction10DiscDVD-R•You can record on the disc only in the Video mode.•You can record until the disc becomes full.•Finalizing the discs allows playback on other DVDplayers. However, the finalized discs can no longerbe recorded.•Discs can be recorded to repeatedly until they arefinalized.NOTES:•There are some players that cannot playback discsthat were recorded with this unit. We cannot guaran-tee the playback with other units.•This unit can record on DVD-RAM/RW/R discs thatare 8 cm in diameter.•This unit cannot record on CD-RW/R.Recording formatThis unit has two modes for formatting discs for record-ing: VR mode and Video mode.When a blank, new disc is loaded into this unit, theautomatic format function starts to format the disc. (Forthe disc format setting in this step, see page 28).VR mode•This mode can be used for DVD-RAM/-RW.•In this mode, the discs can be recorded and editedrepeatedly.•The disc recorded in this mode can be played backwith other DVD-RW-compatible players.•When a Ver.1.1 CPRM or Ver. 1.2 disc is used, youcan record a “Copy Once” program (see page 54).Video mode•This mode can be used for DVD-R and DVD-RW(Ver.1.1/1.2).•When you finalize the disc after recording, the discrecorded with this unit can be played back with otherDVD players.•Recording, editing or playback of an unfinalized disccan be done only with this unit. However, there aresome limitation to editing operations.•In this mode, you cannot record a “Copy Once” pro-gram (see page 54).•When you record a TV program of a bilingual broad-cast, only one of the audio modes can be recorded.You have to select it.Format modes that can be used with each discThe usable format depends on the media type as shownin the below table.Media type Format Available functionsDVD-RAM(Ver.2.0/2.1)DVD-RW(Ver.1.0)DVD-RW(Ver.1.1/1.2)DVD-R(Ver.2.0/2.1)VR modeVR modeVR modeVideo modeVideo modePlayback, recording andediting (Original/playlist)Playback, recording andediting (Original/playlist)Playback, recording andediting (Original/playlist)Playback and recordingEditing (with limitation)Playback and recordingEditing (with limitation)DVD-RAM•When using cartridge-type DVD-RAM discs, it willbe necessary to remove the disc from the car-tridge.•Use only DVD-RAM discs that comply with DVD-RAM standard Version 2.0 or 2.1.The recorder cannot record on a disc formatted inany other standard. When using such a disc, initial-ize it by using the disc-format function of this recorder.•The recorder may not record, dub, or edit some DVD-RAM discs, because they are edited/recorded withanother manufacture’s equipment or PC, contain alarge number of titles, or have little remaining capac-ity. Also, a DVD-RAM disc may not be edited or re-corded if its title contains still pictures.•When you load a DVD-RAM disc for PC, “INCORECTDISC” may appear on screen. In this case pleaseformat the disc to use with this recorder.•DVD-RAM discs formatted in UDF2.0 on a PC arenot compatible with this recorder. Before using thesediscs, initialize them on this recorder.•This recorder complies with current copyrightprotection technology and can copy a disc only whenthe disc permits copying once. When there is noindication on the disc, copying will not be allowed.Such an indication on a disc is required also for theLibrary Management database.DVD-RW•The disc can be erased and used again about 1,000times.•Only the VR mode can be used for Ver.1.0 discs.•With Ver.1.1/1.2 discs, you can record by selectingthe VR mode or Video mode.•When you record in the VR mode, you can repeat-edly record and erase. By erasing unnecessary titles,you effectively increase remaining time.•When you record in the Video mode, you can recorduntil the disc becomes full.•When you use the Video mode, you can newly recordon the disc by formatting the disc. However, if thedisc is formatted, all the recorded contents will beerased.Media type Logo markDVD-RAM Ver.2.0 Ver.2.1DVD-RWVer.1.0, Ver.1.1, Ver.1.2Ver.1.1 CPRM supportVer.1.2 CPRM support(1~6x SPEED)DVD-R Ver.2.0, Ver.2.1(1~16x SPEED)Discs on which video can berecordedTo record video with this unit, use the discs below: 2J40101A P08-11 3/4/06, 10:43 AM10
Introduction11DiscCHAPTER 1TITLE1 TITLE2DVD DISCCHAPTER 2 CHAPTER 2 CHAPTER 3CHAPTER 1TRACK 1 TRACK 2 TRACK 3 TRACK 4 TRACK 5Audio-CDWhen recording in the Video modeWhen a disc recorded in the Video mode is finalized, itcannot be recorded onto any more. Therefore, beforefinalization, be sure to perform all desired recording.After finalization, a title list that can be used by the DVDplayer is automatically created.NOTES:•The finalization process may require from a few min-utes up to 1 hour depending on the disc type and theamount of free space on the disc.•A DVD-RW Ver.1.1/1.2 recorded in the Video modecannot be recorded or edited after finalization, but ifyou format the disc by erasing all the content, youcan again record on this disc.•A finalized disc may not play because of the condi-tion of the DVD or the compatibility with the playerused for playback.•Some players may not playback the discs recordedwith this unit. We cannot guarantee the playback us-ing other players.On Video CDsThis DVD supports Video CDs equipped with thePBC (Version 2.0) function. (PBC is the abbreviationof Playback Control.) You can enjoy two playbackvariations depending on types of discs.•Video CD not equipped with PBC function(Version 1.1)Sound and movie can be played on this DVD/VCRin the same way as an audio CD.•Video CD equipped with PBC function(Version 2.0)In addition to operation of a Video CD not equippedwith the PBC function, you can enjoy playback ofinteractive software with search function by usingthe menu displayed on the TV screen (MenuPlayback). Some of the functions described in thisowner’s manual may not work with some discs.Title/Chapter/TrackA DVD-Video has large partitions called “Titles”, andsmaller partitions within them called “Chapters”.A music CD has other partitions called “Tracks”. A num-ber is allotted to each partition and these numbers arecalled “title numbers”, “chapter numbers” or “track num-bers”.When recording in the VR modeOne-time recording is set to 1 title (1 chapter). How-ever, if you stop recording temporarily or erase scenesby editing, the chapter will automatically be partitioned.The interval between chapters can be specified. (Seepage 32).When recording in the Video modeOne-time recording is set to 1 title. In recording, chap-ters are set automatically. The interval between chap-ters can be specified. (See page 32).NOTES:•The title, chapter and track are numbered, but somediscs may not record the numbers.•Recording on DVD-R/RW in the Video mode is a newstandard approved at the 2000 DVD forum. Confor-mity to this standard varies with each DVD playermanufacturer. Some models of DVD player or DVD-ROM drive, therefore, will not playback recorded vid-eos. •Toshiba is not liable for any damage or loss causeddirectly or indirectly by the malfunction of this DVD/VCR, including, without limitation, any one of thefollowing:•Failure to record contents intended to be recordedby the consumer.•Failure to edit contents as intended by the consumer.•When a DVD-RAM disc or a DVD-R disc createdon this recorder is used (e.g., insertion, playback,recording or editing) in another DVD player, recorderor personal computer drive.•When a DVD-RAM disc or a DVD-R disc that is usedin the manner described in the immediately preced-ing bullet point is used again in this recorder.•When a DVD-RAM disc or a DVD-R disc that wasrecorded in another DVD recorder, or in a personalcomputer drive is used in this recorder.•Discs recorded in this recorder may not operate asexpected on other DVD players, recorders or per-sonal computer drives.Disc playback in other playersDVD-RW/R recorded in this unit can be finalized. Thedisc can be played back in other players that canplayback DVD-RW and DVD-R.For more information on finalization, see “FINALIZE” in“Setting the disc” (page 28).When recording in the VR modeEven if a DVD-RW disc recorded in the VR mode isfinalized, you can record or edit by cancelling thefinalization. (See “UNDO FINALIZE” on page 29).When you playback the disc with another player, makesure that the DVD player supports DVD-RW. 2J40101A P08-11 3/4/06, 10:43 AM11
Introduction12Parts and functionsRearFrontON/STANDBY buttonEJECT button DV IN terminalPLAY buttonSTOP buttonFWD (Fast Forward) buttonREW (Rewind) buttonREC buttonVCR/DVD buttonDisc trayCassette Loading SlotDisplay windowVIDEO IN (INPUT 2) jackS-VIDEO IN (INPUT 2) jackAUDIO (L/R) IN(INPUT 2) jacks*This unit has a door on the front panel.Please open it to access the S-VIDEO jack and the AUDIO (L/R)/VIDEO IN (INPUT 2) jacks.Remote senserCHANNEL / buttonsVCR indicatorOPEN/CLOSE buttonAC power cord COAXIAL DIGITALAUDIO OUT jack (DVD Priority)AUDIO (L/R)/VIDEO OUT jacks(DVD/VCR common)AUDIO (L/R) OUTjacks(DVD Priority)AUDIO (L/R)/VIDEO IN (INPUT 1) jacksS-VIDEOIN (INPUT 1) jackS-VIDEO OUT jack(DVD Priority)COMPONENTOUT jacks (DVD Priority)OPTICAL DIGITALAUDIO OUT jack (DVD Priority)HDMI OUT jackRF IN jackRF OUT jackDVD indicator 2J40101A P12-22 3/4/06, 10:43 AM12
Introduction13No. Display DescriptionLights during video tape playback.1Parts and functionsNOTE:Some discs may not playback correctly, or chapter number, playback time, etc may not be displayed.Display windowVideo tape is temporarily stopped.Lights during video tape recording.Progressive scanning mode.Timer recording display.PP21 3424Appears when a CD is inserted.Appears when a CD-R is inserted.Appears when a DVD-Video is inserted.Appears when a DVD-R is inserted.Appears when a DVD-RW is inserted.Appears when a DVD-RW in VR mode is inserted. When the disc is set to video mode, VR does not appear.Video tape is in the unit.Clock display (Colon [ : ] flashes).Counter display in hour/minute/second.Cable TV channel display.TV channel display.Track number display for CD.Display for afternoon (out in the morning).The external input channel (L1 or L2) display.Error display.Lights during playback of DVD and CD. Flashes in auto resume.DVD or CD is temporarily stopped.Lights during DVD recording.CDCD-RDVDDVD-RDVD-RWVR10:0001H00M00SC 36CH2CHTRK 002PML1/L2Err34 DVD recording modes. XP, SP, LP or SLP can be selected in turn by pressing the REC MODE/SPEED repeatedly.2 VCR recording modes. SP or SLP can be selected in turn by pressing the REC MODE/SPEED repeatedly.SP/SLPXP/SP/LP/SLPAppears when a CD-RW is inserted.CD-RWAppears when a DVD-RAM is inserted.RAMAppears when the tuner built into this unit is not selected. When you press TV/VIDEO, it disappears.TVAppears when HDMI output is active.HD 2J40101A P12-22 3/4/06, 10:43 AM13
Introduction14OPEN/CLOSE Opens or Closes the tray. 34EJECT Ejects the cassette tapes 49PROG Activates the progressive scanning mode. 21HDMI HDMI output on/off. 21TV/VIDEO Select to operate TV/VIDEO 23, 56ON/STANDBY Turns power on/off. 230-9 Direct channel selection of TV 55Setting input 38, 76Entering a password 26INSTANT REPLAY Repeats playback between the section played10 seconds before and present section. 39INSTANT SKIP Skips commercial breaks. 38, 51DISPLAY Displays VCR or DVD operation status. 36, 52VCRDVDCH / Channel selection for the connected TV or VCR 55DUBBING Copies VCR to DVD or DVD to VCR. 78, 79DVD MENU Displays the menu of the DVD disc. 40INPUT SELECT Switches the connected TV to external inputs. 80TOP MENU/TITLE MENUSelects titles of a DVD disc. 35, 40, 43, 64SETUP Display the setup menu 24, 58 / Cursor buttons 24, 34, 38, 58TRK +/– Manual tracking in the playback mode for VCR 51 / Cursor buttons 34, 38ENTER Option selection in the menu 24, 34, 38, 58RETURN Close the menu window. 24, 26CANCEL Deletes the Timer recording program. 60Cancels input data in the setting mode. 26PAUSE/STILL Still picture/Recording pause on/off 37, 51PLAY Playback 34, 50STOP Stop 34, 50, 56SKIP / Skips chapters in the forward or reverse direction 37INDEX / Searches for the INDEX mark of a tape 52SEARCH /REWRewind/Review playback 37, 50, 51SEARCH /F.FWDFast Forward/Forward search playback 37, 50, 51REC MODE/SPEED Selects the recording mode. 55, 57REC/OTR Recording 55, 57, 80TIMER REC Sets the unit to start recording at a preset time. 60SLOW Slow motion playback 37, 51ANGLE Changes playback angle. 41COUNTER RESET Resets the counter to 00H 00M 00S . 52AUDIO Changes the language of the DVD. 42AUDIO SELECT Switches sound between mono and stereo. 62SUBTITLE Selects subtitles of the DVD disc. 42ATR Digital AUTO TRACKING 51CLOCK/COUNTER Changes the front panel display mode. 52ZOOM Zoom (for DVD/Video CD) 41ZERO RETURN Stops the tape when the counter reaches 00H 00M 00S. 52A-B REPEAT Repeats playback between A and B. 39PLAY MODE Selects the playback mode. 38REPEAT Repeats playback. 39, 51Remote control PageParts and functionsSwitches to operation between VCR and DVD.34,50,78 2J40101A P12-22 3/4/06, 10:43 AM14
Introduction15Inserting Batteries into the Remote Control:Parts and functions3Replace the compartment cover.2Install two “AAA” batteries, pay-ing attention to the polarity dia-gram in the battery compart-ment.1Open the battery compartmentcover in the direction of the ar-row.Caution:Never throw batteries into a fire.Notes:•Be sure to use AAA size batteries.•Dispose of batteries in a designated disposal area.•Batteries should always be disposed of with the environment in mind. Always dispose of batteries inaccordance with applicable laws and regulations.•If the remote control does not operate correctly, or if the operating range becomes reduced, replace batterieswith new ones.•When necessary to replace batteries in the remote control, always replace both batteries with new ones.Never mix battery types or use new and used batteries in combination.•Always remove batteries from remote control if they are dead or if the remote control is not to be used for anextended period of time. This will prevent battery acid from leaking into the battery compartment.Remote control basics•Press ON/STANDBY to turn the DVD/VCR on or off.•Press CH or CH to move through the channels one channel at a time.•The /// are also used to navigate on-screen menu system.•You can directly access specific channels using numeric keys.•Each press of DVD or VCR, switches the screen between the DVD screen (DVD mode) and the VCR screen(VCR mode).Operation•Aim the remote control at the remote sensor and press control buttons tooperate.•Operate the remote control within 30° angle on either side of the remotesensor, up to a distance of approximately 7 meters (23 feet).Polarized AC Cord Plug(One blade is wider than the other.)AC OutletWider Holeand BladePower SourceTO USE AC POWER SOURCEUse the AC polarized line cord provided for operation on AC. Insert the ACcord plug into a standard 120V 60Hz polarized AC outlet.NOTES:•Never connect the AC line cord plug to other than the specified voltage(120V 60Hz). Use the attached power cord only.•If the polarized AC cord does not fit into a non-polarized AC outlet, do notattempt to file or cut the blade. It is the user’s responsibility to have anelectrician replace the obsolete outlet.•If you cause a static discharge when touching the unit and the unit fails tofunction, simply unplug the unit from the AC outlet and plug it back in. Theunit should return to normal operation.•If the AC cord plug is plugged in for the first time, wait for approximate 3minutes before operating the unit.Approx.7 meters (23 feet) 2J40101A P12-22 3/4/06, 10:43 AM15
Introduction16NOTES: • A clear picture will not be obtained by the DVD/VCR unless the antenna signal is good. Connect theantenna to the DVD/VCR properly.•For better quality recording, an indoor antenna or a telescopic antenna is not recommended. The useof an outdoor type antenna is required.•If you are not sure about the connection, please refer to qualified service personnel.If you are using an antenna system, follow these instructions. If you are using a Cable TV subscriber, skipahead to page 18 for the proper connections. ANTENNA TO DVD/VCR CONNECTIONThe DVD/VCR must be connected “between” the antenna and the TV. First, disconnect the antenna from the TVand connect it to the DVD/VCR. Then connect the DVD/VCR to the TV. Below are 3 common methods of connect-ing an antenna system to a DVD/VCR. Find the type of antenna system you are using and follow the connectiondiagram.If both UHF and VHF antennas have 300 ohm twin lead (flat) wires,use a combiner having two 300 ohm inputs and one 75 ohm output.NOTE:Antenna connectionsCombination UHF/VHF antenna with 75 ohm coaxial cableCombination UHF/VHF antenna with 300 ohm twin lead (flat) wireSeparate UHF and VHF antennas123DVD/VCR75 ohm coaxial cable75 2J40101A P12-22 3/4/06, 10:43 AM16
Introduction17NOTE: If a UHF or VHF antenna is used,set the TV/CABLE menu optionto the “TV” mode.TV with single 75 ohm UHF/VHF antennainputNOTE: If a UHF or VHF antenna is used,set the TV/CABLE menu optionto the “TV” mode.TV with 300 ohm UHF and 75 ohm VHFantenna inputsNOTE: If a UHF or VHF antenna is used,set the TV/CABLE menu option tothe “TV” mode.TV with 300 ohm UHF and 300 ohm VHFantenna inputs DVD/VCR TO TV CONNECTIONAfter you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV.Below are 3 common methods of connecting your DVD/VCR to a TV. Find the type of TV you are using and followthe connection diagram.This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate UHF and VHF antennainputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for UHF and VHF reception.Antenna connectionsThe unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs and othermaterials, is prohibited under the Copyright Laws of the United States and other countries, and may subjectyou to civil and/or criminal liability.UHF/VHF INTV75 ohm coaxial cable (supplied) 2J40101A P12-22 3/4/06, 10:43 AM17
Introduction18Many cable companies offer services permitting reception of extra channels including pay or subscription chan-nels. This DVD/VCR has an extended tuning range and can be tuned to most cable channels without using a cablecompany supplied converter box, except for those channels which are intentionally scrambled. If you subscribe toa special channel which is scrambled, you must have a descrambler box for proper reception.Cable TV connectionsNOTE: Whenever a converter/descrambler box is placed before the DVD/VCR, you must tune the DVD/VCR to theoutput of the converter/descrambler box, usually channel 3 or 4.ALLOWS: • Recording of nonscrambled channels.•Use of the programmable timer.•Recording of one channel while watching another.ALLOWS: • Recording of channels through the converter box(scrambled and unscrambled).•Using the programmable timer to record only thechannel selected at the converter box.PREVENTS: • Recording one channel while watching another.•Using the DVD/VCR tuner to select channels.123ALLOWS: • Recording of channels through the converter box(scrambled and unscrambled).•Using the programmable timer to record only thechannel selected at the converter box.PREVENTS: •Using the DVD/VCR tuner to select channels.•Recording one channel while watching another.NOTE:If you are playing a tape or using thetuner built into the DVD/VCR, the con-verter must be set to the video channeloutput of the DVD/VCR (either 3 or 4).NOTE:To record from converter/descrambler,DVD/VCR tuner must be tuned to theconverter output channel, usually chan-nel 3 or 4. 2J40101A P12-22 3/4/06, 10:43 AM18
Introduction19IMPORTANT: Make sure the TV/CABLE menu option is set to the “CABLE” mode.This DVD/VCR cannot receive scrambled programs since it does not contain a descrambler. In order to receive scrambledprograms, your existing descrambler must be used. Descrambler boxes are available from cable companies. Consult yourlocal cable company for more information concerning connection to their descrambler equipment. There are many waysto connect your DVD/VCR to a cable system. Below are six common methods of connection.456ALLOWS: • Recording of one channel while watching another.•Using the programmable timer to record only the channel selected at the converter box.•Recording of all channels through the converter box.PREVENTS: • Watching scrambled channels while recording another channel.•Using the DVD/VCR tuner to select channels.ALLOWS: • Recording of nonscrambled channels.•Recording of one channel while watching another.•Watching premium channels through the converter while recording nonscrambled channels.•Using the programmable timer.PREVENTS: Recording scrambled channels.ALLOWS: • Recording of all channels through the converter box.•Recording a scrambled or unscrambled channel while watching another (scrambled orunscrambled) channel.•Using the programmable timer to record only the channel selected at the converter box.PREVENTS: Using the DVD/VCR tuner to select channels.Cable TV connectionsThe unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs and othermaterials, is prohibited under the Copyright Laws of the United States and other countries, and may subjectyou to civil and/or criminal liability. 2J40101A P12-22 3/4/06, 10:43 AM19
Introduction20Connections with the TV or audio componentThe exact arrangement you use to interconnect various videoand audio components to the DVD/VCR is dependent on themodel and features of each component. Check the Owner’sManual provided with each component for the location of videoand audio inputs and outputs.Connect to a TV with Audio/Video outputYou can enjoy playback by connecting the unit to a TV.Connect the unit to a TV equipped with audio input (L/R) and video input jacks using the supplied audio/video cable.Connect to a TV with S-Video outputIf your TV has an S-Video input, you can get higher quality by connecting it with the S-Video output of the unit usingthe S-Video cable instead of connecting the video input of the TV to the video output jack of the unit.Connect to a TV with Component video outputYou can enjoy the highest quality picture by connecting the unit’s component video out jacks to the componentvideo input jacks of your TV, with component video cables (not supplied).To switch the output signals (Progressive/Interlace):Press PROG/HDMI to change the video output signals (progressive and interlace) from Component video outputjacks (see page 21).The unauthorized recording, use, distribution,or revision of television programs, videotapes,DVDs and other materials, is prohibited underthe Copyright Laws of the United States andother countries, and may subject you to civiland/or criminal liability. 2J40101A P12-22 3/4/06, 10:43 AM20
Introduction21Connect to a TV with HDMI outputHDMI stands for High Definition Multimedia Interface. HDMI transfers digital audio and uncompressed digitalvideo on a single cable. As a result, audio cables and video cables don’t need to be connected separately to adevice. In addition, HDMI is compatible with HDCP (High Bandwidth Digital Content Protection).HDMI Cable (not supplied)HDMI-compatibledisplayTo HDMI inputTo HDMI OUTConnections with the TV or audio componentFor proper operation, it is recommended that you useas short an HDMI cable as possible.Notes:•Refer to the owner’s manual for the TV to be connected to this recorder for more information concerningHDMI connections.•HDMI is an evolving technology, so it is possible that some devices may not operate properly with this recorder.•No sound will be output from the HDMI OUT jack if the “DOLBY DIGITAL OUTPUT” is not set to “PCM” (seepage 32).Switching the output signals (HDMI/Progressive)1. Turn ON the TV and set to the appropriate input mode (HDMI or Component).2. Press PROG/HDMI on the remote control to change the video output signals (HDMI/Progres-sive) as below.The content of the output for each ouput jacks are as shown in the following table and differdepending on output setting.*When the HDMI/Progressive is active, it is impossible to output any video images from the Video out jack andS-Video out jack. In this case, press PROG/HDMI repeatedly to switch the HDMI/Progressive output setting to“OFF” or set the TV to Component input mode/HDMI input mode.Notes:•PROG/HDMI button is not available during VCR mode.•720p and 1080i are available when the unit is connected to the HDMI-compatible display.•When the HDMI mode is active, the HDMI indicator “HD” on the display window will light up.•If the HDMI cable is disconnected when the HDMI mode is active, the HDMI indicator “HD” on the displaywindow will flash. In this case, press PROG/HDMI repeatedly to switch the HDMI output setting to “OFF”, orconnect the HDMI cable again.• When the progressive mode is active, the Progressive indicator “ P ” on the display window will light up.•When the HDMI mode is active, you cannot use Dubbing function (see pages 78 and 79).•If your TV is not compatible with progressive scan, press and hold the STOP button on the front panel forabout 3 seconds to return to normal picture.HDMI ComponentOFF 480i (Interlace)480p (Progressive) 480p (Progressive)720p (Progressive) 480p (Progressive)1080i (Interlace) 480p (Progressive) 2J40101A P12-22 3/4/06, 10:43 AM21
Introduction22Connections with the TV or audio componentConnect to a stereo amplifier with audio outputYou can enjoy high quality audio by connecting the audio output to your amplifier.Connect the audio output jacks to any line-level inputs (such as AUX, DVD, CD, etc.) of an audio amplifier.Connect to an AV Amplifier with built-in digital surroundIf you are using an Amplifier with a built-in digital surround as follows, you can enjoy the various audio systemssuch as Dolby Digital and DTS by using the optical or coaxial digital output.Use this connection to connect an:•AV amplifier with built-in *Dolby Digital decoder•AV amplifier with built-in *DTS decoderConnecting the optical digital cableYou may connect to an AV Amplifier with an optical digital cable (not supplied) instead of a coaxial digitalcable.When you connect the optical digital cable (not supplied), remove the dust protection cap from the rear panel.When not using the optical digital cable, attach the dust protection cap to protect against dust.NOTES:•When you make the connections above, do not set DOLBY DIGITAL to DOLBY DIGITAL or DTS to ON on the AVamplifier. If you do, a loud noise will suddenly come out from the speakers, affecting your ears or causing thespeakers to be damaged.•Caution for the optical digital audio output connector: Do not connect to an amplifier (with an optical digital inputconnector) which does not contain a Dolby Digital or DTS decoder. Otherwise, any attempt to play DVDs maycause such a high level of noise that it may be harmful to your ears and damage your speakers.•DTS audio will be output only from the COAXIAL or OPTICAL output. To hear DTS audio, DTS-Decoder isnecessary.•When playing DTS-encoded CDs, only noise will be heard from the speakers or analog stereo outputs.•Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit.•The optical or coaxial digital output jack output sounds in the bitstream.NOTE:You may connect to a TV with a componentvideo cable (not supplied) or S-Video cable(not supplied) instead of a video cable (notsupplied).DVD/VCRAV Amplifier with built-in variousdecoder as aboveVideo outputTo Audio/Video inputCoaxial digital audio outputCoaxial digital cable (not supplied)Audio/Video cable (supplied)TVAudio(R) outputAudio(L) outputConnect eitherOptical digital cable (not supplied)Optical digital audio output 2J40101A P12-22 3/4/06, 10:43 AM22
23IntroductionAuto clock setting / Setting the video channelNOTES:•When shipped from factory, thevideo channel is set to CH 3.•If the unit does not operate prop-erly, or there is no key operationfrom the unit and/or the remotecontrol: Static electricity, etc., mayaffect the operation. Disconnectthe AC power cord once, then con-nect it again.Auto clock settingPreparation:You must connect the antenna or cable before connecting the AC cordto the power source.After the antenna or cable is connected, wait for at least 3 minutes withthe power turned off for the auto clock feature to activate.After the clock is set automatically, you may have to set the StandardTime (time zone) and Daylight Saving Time. (See 27.)Press ON/STANDBY to turn on the DVD/VCR after the auto clock op-eration completed.• When shipped from factory, the “AUTO CLOCK” option is set to “ON”position.• If you turn the DVD/VCR on during auto clock setting, the clock is notset.• Depending on the reception condition, auto clock setting may takeapprox. 30 minutes.•After a power failure or disconnection of the power plug, the clock willbe lost. In this case, wait 3 minutes before turning the DVD/VCR on.•With cable box connection, if the auto clock setting is unsuccessful,select the PBS channel carrying the XDS information, then turn theDVD/VCR off. After 3 minutes, turn the DVD/VCR on.•If the clock is not set automatically, set the clock manually. (See page27.)Setting the video channelTo view playback of a recorded tape or DVD disc, or to watch aprogram selected by the VCR’s channel selector, the TV must beset to channel 3 or 4 (video channel).When a TV is connected with the 75 ohm coaxial cable only:1Press and hold 3 or 4 on the remote control for 3 seconds in thestandby mode to select CH 3 or 4. The selected channel numberwill flash on the display for about 4 seconds.2Tu rn ON the TV and set to CH 3 or 4 to correspond with the chan-nel selected in step 1.3Press ON/STANDBY to turn on the DVD/VCR.4Press TV/VIDEO to select the VIDEO position.The TV indicator will disappear in the display.5Select any channel to receive a TV station in your area.The channel number will appear on the screen for about 4 sec-onds.For a push-button TV tunerIf CH 3 or 4 corresponding to the video channel cannot be tuned onyour TV, proceed as follows: set the VCR 3/4 channel selector and theTV to CH 3 or 4, playback a prerecorded tape and tune the TV to re-ceive a sharp color picture from the video cassette recorder. Refer toyour TV owner’s manual for details. 2J40101A P23-33 3/4/06, 10:43 AM23
Various settings24SETUP MENUThe SETUP MENU consists of several menus whereyou can make various settings concerning lan-guage, audio functions, and images. In addition, thismenu includes a clock, channel and other thingsthat require setting just after purchase.For details of each menu, see the correspondingsection in this chapter.Using the SETUP MENUThe following example shows the basic setting proce-dure of the SETUP MENU. The remote control keysthat operate the SETUP MENU are displayed at thebottom of the screen.1Press SETUP while the DVD or video tape isstopped.The SETUP MENU screen will appear.2Press or to select the desired menu and pressENTER.The submenu screen of the selected menu will ap-pear.3Press or to select the desired submenu andpress ENTER.The screen for the selected submenu will appear.4Press or to select the desired item you wantand press ENTER.Selectable items will be listed.5Press or to select the desired item and pressENTER.This completes the setting procedure.•To return to the previous screen, press RETURN.•To close the SETUP MENU, press SETUP.NOTES:•For items that require different operations from thebasic setting procedure, the setting procedure is de-scribed in each individual section.•The item which is indicated by blue color cannot beselected.•“TIMER REC SET” cannot be selected when theclock is not set.TIMER REC SETSYSTEM SETUPAV SETUPREC SETUPCH SETUPOTHERSETUP MENURETURN SETUPENTERENTER BACK ENDSELECTTIMER REC SETSYSTEM SETUPAV SETUPREC SETUPCH SETUPOTHERLANGUAGEPARENTALCLOCKDISC SETUPOTHERSETUP MENURETURN SETUPENTER BACK ENDSELECTENTERTIMER REC SETSYSTEM SETUPAV SETUPREC SETUPCH SETUPOTHERLANGUAGEOSD LANGUAGEDVD MENUAUDIOSUBTITLESETUP MENURETURN SETUPENTER BACK ENDENGLISHENGLISHAUTOMATICENGLISHSELECTENTERTIMER REC SETSYSTEM SETUPAV SETUPREC SETUPCH SETUPOTHERLANGUAGEOSD LANGUAGEDVD MENUAUDIOSUBTITLESETUP MENURETURN SETUPENTER BACK ENDENGLISHENGLISHAUTOMATICENGLISHSELECTENGLISHFRANCAISESPANOLOTHERAUTOMATICOFF----ENTER 2J40101A P23-33 3/4/06, 10:43 AM24
25Various settingsSetting the languageYou can choose the language of the menu screen,DVD menu, DVD audio and subtitles.Preparation:• Turn ON the TV and set it to the video input mode.• Select “LANGUAGE” from “SYSTEM SETUP”. Forthe procedure, see steps 1 to 3 in “Using the SETUPMENU” on page 24.Selectable languages:ENGLISH, FRANCAIS, ESPANOLThe language you have selected will play if it is re-corded on the disc.ORIGINALThe unit will select the first priority language of eachdisc.OTHERIf you want to select another language, before press-ing ENTER, input the language code by using thenumeric keys. (See the Language code list on page84). Then press ENTER.•If you input a wrong number, press CANCEL.NOTE:If the selected language is not recorded on the disc,the first priority language is selected.SUBTITLEWhen several subtitles languages are recorded on DVD,you can select the language to be used for the sub-titles. The selected language remains in effect after thepower is turned off or the disc is replaced.Select “SUBTITLE” and select the menu language fromthe below.Selectable languages:ENGLISH, FRANCAIS, ESPANOLThe subtitle is displayed with the selected languageif it is recorded on the disc.OTHERIf you want to select another language, before press-ing ENTER, input the language code by using thenumeric keys. (See the Language code list on page84). Then press ENTER.•If you input a wrong number, press CANCEL.AUTOMATIC•The unit will automatically select the same languagein the AUDIO setting.•When the unit selects the same language as theAUDIO setting, the subtitles will not appear duringplayback.•When you do not use the same language as theAUDIO setting, the subtitles will appear during play-back.OFFSubtitles do not appear.NOTE:If the selected language is not recorded on the disc,the first priority language is selected.OSD LANGUAGEYou can set the language for on screen display.Select “OSD LANGUAGE” and select the language fromthe below.Selectable languages:ENGLISH, FRANCAIS, ESPANOLDVD MENUWhen several menu languages are recorded on a DVD,you can select the language to be used for the DVDmenu.Select “DVD MENU” and select the language from thebelow.Selectable languages:ENGLISH, FRANCAIS, ESPANOLThe selected language is the first priority menu lan-guage.OTHERIf you want to select another language, before press-ing ENTER, input the language code by using thenumeric keys. (See the Language code list on page84). Then press ENTER.•If you input a wrong number, press CANCEL.AUDIOWhen several audio languages are recorded on a DVD,you can select the audio language to be played back.The selected language remains in effect after the poweris turned off or the disc is replaced.Select “AUDIO” and select the audio language from thebelow.TIMER REC SETSYSTEM SETUPAV SETUPREC SETUPCH SETUPOTHERLANGUAGEOSD LANGUAGEDVD MENUAUDIOSUBTITLESETUP MENURETURN SETUPENTER BACK ENDENGLISHENGLISHAUTOMATICENGLISHSELECTENTER 2J40101A P23-33 3/4/06, 10:43 AM25
Various settings26Setting the parental controlSome discs are specified as not suitable for chil-dren. This unit can prevent playback of such discs.Preparation:• Turn ON the TV and set it to the video input mode.• Select “PARENTAL” from “SYSTEM SETUP”. For theprocedure, see steps 1 to 3 in “Using the SETUPMENU” on page 24.NOTES:• The selected level will apply to operations executedafter this.•The unit cannot restrict playback of some discs.• Some discs may not be encoded with specific ratinglevel information though its disc jacket says “adult”.Parental control will not work with those discs.•If you forget your password, open the disc tray; if thereis a disc inside then remove it and close the tray. Toreset the code, press and hold number 7 on the re-mote control, then press and hold STOP on the frontpanel at the same time. The On-Screen Display willshow “PARENTAL UNLOCK”. You can now set a newpassword.Temporarily cancelling parental con-trolParental control can temporarily be canceled with someDVDs.1Playback a DVD. (See page 34.)2If the DVD disc has been designed to temporarilycancel the rating level, the screen that follows the“READING” screen will change. If you select “YES”with the ENTER, the message “YOUR DISC EX-CEEDS THE PARENTAL CONTROL LEVEL1.”(e.g.) will then appear.3If you wish to cancel the set rating level temporarily,select “PARENTAL CONTROL LEVEL” with or, then press ENTER. If the password has beenselected, the password input screen will appear.Alternatively, if the password has not been set, play-back will commence. If you don’t know (or have for-gotten) the password, select “CANCEL PICTURE”.The setting screen will disappear. Press OPEN/CLOSE to remove the disc.4Use the numeric keys to input the password.•To interrupt the input process, press RETURN.5Press ENTER.6Playback will commence if the entered passwordwas correct.NOTE:This temporary cancellation of the rating level will re-main active until the disc is ejected.When the disc is ejected, the original rating level will beset again automatically.Selecting parental controlSelect “PARENTAL” and select the parental control levelfrom the below.Level Off:Parental control is turned off.Level 1:Adult discs and general discs (R-rateddiscs included) cannot be played back.Level 2 to 3:Adult discs and R-rated discs cannotbe played back.Level 4 to 7:Adult discs cannot be played back.(Level 4 to 7 discs contain content chil-dren age 15 and younger may not see.)Level 8:Virtually all discs can be played backwithout restriction.Select from level 1 to level 8.On a scale of 1- 8, “1” is the most restrictive.To lock the selected parental control level1To lock the selected parental control level, press or to select “PASSWORD”.2Use the numeric keys to input a 4-digit password.• If you input a wrong number, press CANCEL.• Be sure to remember this number!3Press ENTER.To cancel the locked parental control level1Select “PASSWORD” shown in step 1 of the above sec-tion and use the numeric keys to input the password.2Press ENTER.The locked mark “” will change to an unlockedmark “ ”.Then, you can change the parental control level, orenter a new password.TIMER REC SETSYSTEM SETUPAV SETUPREC SETUPCH SETUPOTHERLANGUAGEPARENTALCLOCKDISC SETUPOTHERPARENTALPASSWORDPARENTALSETUP MENURETURN SETUPENTER BACK ENDDELETECANCEL- - - -INPUT NO.09SELECTPARENTALOFFENTER----change to1234YOUR DISC EXCEEDS THE PARENTALCONTROL LEVEL 1.PARENTAL CONTROL LEVELCANCEL PICTURE 2J40101A P23-33 3/4/06, 10:43 AM26
27Various settingsSetting the clockThe clock is set to the correct time automatically,but it can also be set manually. The clock can be setfor daylight saving time and time zone.Preparation:•Turn ON the TV and set it to the video input mode.•Select “CLOCK” from “SYSTEM SETUP”. For theprocedure, see steps 1 to 3 in “Using the SETUPMENU” on page 24.CLOCK (manually)You can manually set the date, year and present timewith the remote control.Ex.: Setting the clock to “10:20AM” March, 25th, 2006.1Select “CLOCK” and press ENTER.2Select the desired items using or (month,date, year, hour, minute and AM/PM), then pressENTER.3Press or to set the value of the selected item.4Repeat steps 2 and 3 to set the date, year andpresent time, and press ENTER. The SETUPMENU will close.This completes clock time setting.AUTO CLOCKYou can automatically set the clock by turning “ON” theAUTO CLOCK function.When you want to set the auto clock function to “OFF”,select “AUTO CLOCK”, press ENTER and select “OFF” .For more information see page 23.STANDARD TIME (Time zone)In the rare event that you live within the broadcast rangeof two stations in two different time zones, the DVD/VCR may recognize the wrong station for the auto clockset. To correct the situation:Select “STANDARD TIME” and select the time zone fromthe below.Selectable time zones and correction timesATLANTIC:GMT – 4 hours(GMT: Greenwich Mean Time)EASTERN:GMT – 5 hoursCENTRAL:GMT – 6 hoursMOUNTAIN:GMT – 7 hoursPACIFIC:GMT – 8 hoursALASKA:GMT – 9 hoursHAWAII:GMT – 10 hoursAUTOMATIC:AUTO SETNOTES:•When shipped from the factory, the “STANDARDTIME” is set to “AUTOMATIC”.• After making the auto clock setting, in some casesthe clock may display another time zone. You can cor-rect the clock by selecting your time zone settingabove.• When the clock is not set or you set the clock manu-ally, the time zone setting is not available.DAYLIGHT SAVING TIMEYou can set the clock to daylight saving time automati-cally or manually.To select daylight saving time, select “DAYLIGHT SAV-ING TIME” and select “ON”, while to cancel the day-light saving time, select “OFF”.ON:For manual setting (forward 1 hour)OFF:For manual setting (back 1 hour)AUTOMATIC:For automatic setting (read XDS in thesignal)NOTES:•When you want to set daylight saving time, on thefirst Sunday in April you set it to “ON”, and on the lastSunday in October you set it to “OFF”.•When shipped from the factory, the “DAYLIGHT SAV-ING TIME” option is set to “AUTOMATIC”.•When the clock is not set, the daylight saving timesetting is not available.•When there is no daylight saving time in your area,always select “OFF”. 2J40101A P23-33 3/4/06, 10:43 AM27
Various settings28Setting the discTIMER REC SETSYSTEM SETUPAV SETUPREC SETUPCH SETUPOTHERDISC SETUPREFORMAT AS DVD VIDEOREFORMAT AS DVD VRNEW DISC FORMATFINALIZEPROTECT DISCUNDO FINALIZEDVD-RAM Physical FormatPROCEEDVRPROCEEDOFFPROCEEDPROCEEDPROCEEDSETUP MENURETURN SETUPENTERENTER BACK ENDSELECTREFORMATSTART CANCELFINALIZINGPLEASE WAITREFORMATFINALIZESTART CANCELNEW DISC FORMATSTART CANCELINITIALIZING DISCYou can format, protect, or finalize a disc.Preparation:• Turn ON the TV and set it to the video input mode.• Select “DISC SETUP” from “SYSTEM SETUP”. Forthe procedure, see steps 1 to 3 in “Using the SETUPMENU” on page 24.REFORMATYou can format a recorded DVD-RAM/RW.Check the content of the disc before format. If you for-mat the disc, the recorded content of the disc will beerased.To format a disc in the Video mode, select “REFOR-MAT AS DVD VIDEO”, and to format it in the VR mode,select “REFORMAT AS DVD VR”. You cannot select“REFORMAT AS DVD VIDEO” when DVD-RAM in-serted. The screen below will appear.• When you select “START” and press ENTER, formatwill start. The screen below will appear.• When you select “CANCEL” and press ENTER, theDISC SETUP screen will appear.NOTES:•When the format finished, “REFORMATTINGCOMPLETED PRESS ENTER.” will appear. PressENTER to clear the screen.•You cannot format Ver. 1.0 DVD-RW and DVD-R.•You cannot format a disc if the disc protection is “ON”.In such a case, be sure to cancel the disc protection(see page 29) before format.•You cannot format a DVD-RAM in the Video mode. •When you select “CANCEL” and press ENTER,the DISC SETUP screen will appear.NEW DISC FORMATIf you insert an unused DVD-RW disc, the disc is auto-matically formatted.If you use the DVD-RW (Ver.1.1/1.2), you can selectthe mode to be used for automatic format.Select “NEW DISC FORMAT” and select the mode fromthe list below.VR:Format the disc in the VR mode.VIDEO:Format the disc in the Video mode.When you insert an unused disc, the following mes-sage screen will appear.• When you select “START” and press ENTER, formatwill start. The screen below will appear.• When you select “CANCEL” and press ENTER, thenormal TV screen will appear.NOTES:•When the Initialization finished, “INITIALIZINGCOMPLETED PRESS ENTER” will appear. PressENTER to clear the screen.•If a recorded disc has scratches or contamination onit, the “NEW DISC FORMAT” screen may appear.If this happens, select “CANCEL”.FINALIZETo play a DVD disc recorded on this unit you must finalizethe disc to insure compatibility with other DVD players. Inaddition, if you are using a DVD-RW disc you must recordin Video mode.When “FINALIZE” is selected, the screen below will appear.•When you select “START” and press ENTER, final-ization will start. The screen below will appear. 2J40101A P23-33 3/4/06, 10:43 AM28
29Various settingsSetting the disc / Other (SYSTEM SETUP)UNDO FINALIZEYou can cancel the finalization of a finalized DVD-RW(in VR mode).You cannot cancel the finalization for discs other thanabove. You can record or edit on a disc whose finaliza-tion has been canceled.Select “UNDO FINALIZE”, and the screen below willappear.•When you select “START” and press ENTER, thecancelling finalization will start. The screen below willappear.• When you select “CANCEL” and press ENTER, theDISC SETUP screen will appear.NOTES:•During unfinalizing, the cursor will move repeatedly.When cancelling finalization is complete, “UNDOFINALISING COMPLETED PRESS ENTER” will ap-pear. Press ENTER to clear the screen.•The cancelling finalization process may require a fewminutes to about 1 hour according to disc type or theamount of free space on the disc.•When the disc’s finalization cannot be canceled, youcannot select “UNDO FINALIZE”.DVD-RAM Physical FormatPhysically formats a DVD-RAM disc. Whenever you usea new disc for the first time, be sure to format it.NOTE:The physical format process may require about 1 houraccording to disc condition.This section describes the other setting in SYSTEMSETUPPreparation:•Turn ON the TV and set it to the video input mode.•Select “OTHER” from “SYSTEM SETUP”. For the pro-cedure, see steps 1 to 3 in “Using the SETUP MENU”on page 24.DIMMER (Brightness of the displaywindow)You may adjust the brightness or turn off the display onthe front panel of the unit. Select “DIMMER” and selectthe display window status from the below.AUTOMATIC:When the power is on, the display win-dow appears bright. When the poweris off, it appears dark.DIM:The window display always appearsdark.OFF:When the power is on, the display win-dow appears dark. When the power isoff, it is turned off.DISPLAY/CALL (Turning the screen dis-play “ON” or “OFF”)You can turn off the screen display that is output to theTV screen by this unit. Select “DISPLAY/CALL”, andselect “ON” or “OFF”.ON:The screen display appears.OFF:Nothing but the SETUP MENU and error mes-sages appear.TIMER REC SETSYSTEM SETUPAV SETUPREC SETUPCH SETUPOTHERLANGUAGEPARENTALCLOCKDISC SETUPOTHERSETUP MENUOTHERDIMMERDISPLAY/CALLAUTOMATICONUNFINALIZINGPLEASE WAITNOTES:•During finalizing, the cursor will move repeatedly.When the finalization finished, “FINALISING COM-PLETED PRESS ENTER” will appear. Press ENTERto clear the screen.•The finalization process may require a few minutesto about 1 hour according to disc type or the amountof free space on the disc.•You can record or edit a finalized DVD-RW (in VRmode) by cancelling the finalizing, but you cannot dothese operations with a DVD-RW (Video mode), orwith a DVD-R.•You cannot playback a disc recorded on VR mode ona unit that does not support DVD-RW.•Even if you finalize a disc in the Video mode, the disccannot be played back in some DVD players.•A DVD-R disc cannot be named after it is finalized.PROTECT DISCYou can protect a disc to prevent the content recordedon it from being erased, edited or re-recorded.Only DVD-RAM and DVD-RW (in VR mode) can beprotected.Select “PROTECT DISC” and select “ON” to protect thedisc.To cancel the disc protection, select “OFF”.UNDO FINALIZESTART CANCEL 2J40101A P23-33 3/4/06, 10:43 AM29
Various settings30Setting the screenNote for the field still and frame still:(with 480i interlaced scanning mode)•Field* still (240 lines)Since only one field (half of the video information) isshown on the TV screen, the picture appears roughbut does not shake.•Frame* still (480 lines)Tw o fields are alternatively shown on the TV screen.The picture shakes but the resulting picture quality issuperior to the field still pictures.Field*: A field refers to the video information in one-half of a frame. 1 frame (screen) consists of 2fields.Frame*: A frame refers to the total area occupied byeach picture on the TV screen.LINE1 INPUT/LINE2 INPUTThis unit comes with an S-Video input jack and Videoinput jack. When you use an S-Video or Video inputjack, you must select the input mode.Select “LINE1 INPUT” (“LINE2 INPUT”) and select themode from the below.S-VIDEOThe video signal is input to the S-Video input jack aspriority.VIDEOThe video signal is input only to the video input jack.TIMER REC SETSYSTEM SETUPAV SETUPREC SETUPCH SETUPOTHERAV SETUP 1TV SCREENSTILL MODELINE1 INPUTLINE2 INPUTSETUP MENURETURN SETUPENTER BACK END4:3 Letter boxAUTOMATICVIDEOVIDEOSELECTENTERThis section describes settings about the screen.Preparation:•Turn ON the TV and set it to the video input mode.•Select “AV SETUP 1” from “AV SETUP”. For the pro-cedure, see steps 1 to 3 in “Using the SETUP MENU”on page 24.TV SCREENYou can select the TV screen size to suit the screenimage.Select “TV SCREEN” and select screen size from thebelow.4:3 Pan scanIt displays a wide picture across the whole screenwith left and right edges automatically cut off.4:3 Letter boxSelect this mode when connecting to a conventionalTV. When playing back a wide screen DVD disc, itdisplays a wide picture with black bands at the topand bottom of screen.16:9Select this mode when connecting to a wide-screenTV. A wide-screen picture is displayed in full size.NOTE:If the DVD disc is not formatted in the pan scan format,it displays a 4:3 aspect ratio.STILL MODEYou can set the type of image displayed on the TVscreen when the playback of the DVD is stilled.Select “STILL MODE” and select the image to be dis-played from the below.AUTOMATICThe field still or frame still is automatically selected.(For normal use.)STILL BY FRAMEThe frame still is set. 2J40101A P23-33 3/4/06, 10:43 AM30
31Various settingsThis section describes image quality settings.Preparation:• Turn ON the TV and set it to the video input mode.•Select “AV SETUP 2” in “AV SETUP”. For theprocedure, see steps 1 to 3 in “Using the SETUPMENU” on page 24.BRIGHTNESSYou can control the brightness level of the image.Select “BRIGHTNESS” and select the level from thebelow.MAX:The image becomes brighter.STD:The image is of standard brightness.MIN:The image becomes darker.Setting the image quality / Setting the audioThis section describes audio settings.Preparation:•Turn ON the TV and set it to the video input mode.•Select “AUDIO” from “AV SETUP”. For the proce-dure, see steps 1 to 3 in “Using the SETUP MENU”on page 24.DRCDRC (Dynamic Range Control) enables you to controlthe dynamic range so as to achieve a suitable soundfor your equipment.Select “DRC” and select the level from the below.MAX:Full dynamic range is maintained.STD:Full dynamic range is reduced.TV:Dynamic range is reduced.NOTES:•This function works only during playback of DolbyDigital recorded discs.•When you listen to the sound from TV’s speaker, werecommend that you select “TV”.•The level of Dynamic Range Reduction may differdepending on the DVD.VIRTUAL SURROUND (Spatializer N-2-2TM)Sound that is not recorded in the surround mode willbe changed to artificial surround sound and output.Select “VIRTUAL SURROUND” and select “ON” to ac-tivate the virtual surround function. Select “OFF” to can-cel the virtual surround function.NOTE:This function does not work with a video tape.EXTERNAL AUDIO INPUTThe audio mode for the audio input jack can be se-lected, choosing either stereo or monaural.Select “EXTERNAL AUDIO INPUT” and select from thebelow.STEREO:The sound is treated as stereo sound.L CH:The sound is treated as the monauralsound of the left channel.R CH:The sound is treated as the monauralsound of the right channel.TIMER REC SETSYSTEM SETUPAV SETUPREC SETUPCH SETUPOTHERAUDIODRCVIRTUAL SURROUNDEXTERNAL AUDIO INPUTSAPDOLBY DIGITAL OUTPUTSTDOFFSTEREOOFFPCMSETUP MENURETURNENTER BACK ENDSELECTSETUPENTERTIMER REC SETSYSTEM SETUPAV SETUPREC SETUPCH SETUPOTHERAV SETUP 2BRIGHTNESSE.B.L.SETUP MENURETURN SETUPENTER BACK ENDSTDOFFENTER SELECTE.B.L.To select the black level of playback pictures, set yourpreference and monitor’s ability.ON:Enhanced grey scale (0 IRE cut off)OFF:Standard grey scale (7.5 IRE cut off)NOTE:The E.B.L. function only works when playing back DVD-Video, DVD-RAM/RW/R or Video-CDs. 2J40101A P23-33 3/4/06, 10:43 AM31
Various settings32Setting the audio / Setting the recordingSAP (Second Audio Program)This unit is fitted with an SAP broadcast system thatenables you to switch to a second audio program whileviewing a selected channel.This function applies only when the program is broad-cast in multiple languages through the SAP broadcastsystem.Select “SAP” and select “ON” to activate SAP. Select“OFF” to cancel.Listening to SAPWhen the unit is turned on or a channel selection ismade, make certain the letters “SAP” appear on thescreen. This means that “Second Audio Program”broadcasting is available.DOLBY DIGITAL OUTPUTSelect from the following methods of outputting the au-dio of discs that were recorded with Dolby Digital.DOLBY DIGITAL: Outputs in Dolby Digital sound.PCM: Converts the sound to PCMand outputs it.NOTE:Select PCM if you are connected to an audio amplifierand the amplifier is not Dolby Digital compatible.TIMER REC SETSYSTEM SETUPAV SETUPREC SETUPCH SETUPOTHERREC SETUPINITIAL REC TOINITIAL REC MODEAUTO CHAPTERINDEX PICTUREBLACK LEVEL (REC)SETUP MENURETURN SETUPENTER BACK ENDDVDSP10MIN0 SECStandardSELECTENTERThis section describes recording settings.Preparation:•Turn ON the TV and set it to the video input mode.•Select “REC SETUP”. For the procedure, see steps1 to 3 in “Using the SETUP MENU” on page 24.INITIAL REC TOYou can select the recording media that is first displayedin the item “REC TO” on the timer recording screen.Select “INITIAL REC TO” and select “DVD” or “VCR”.INITIAL REC MODEYou can select the recording mode that is first displayed inthe item “REC MODE” on the timer recording screen.Select “INITIAL REC MODE” and select XP, SP, LP, or SLP.NOTES:•For the DVD recording mode, see page 53. And forthe VCR recording mode, see page 49.•Even if you select the recording mode by “INITIALREC MODE”, the recording mode on the displaywindow does not change. If you want to change therecording mode, press REC MODE/SPEED on theremote control.AUTO CHAPTERYou can automatically make chapter marks on the DVDto be recorded.Select “AUTO CHAPTER” and select the interval be-tween chapter marks from the below.OFF:The automatic chapter is not used.5 MIN:The interval is set to 5 minutes.10 MIN:The interval is set to 10 minutes.15 MIN:The interval is set to 15 minutes.30 MIN:The interval is set to 30 minutes.INDEX PICTUREYou can set the time that the thumbnail image is regis-tered in the title menu of DVD-RW (VR mode).Select “INDEX PICTURE” and select from the below.0 SEC:The image of a recording start point is regis-tered.1 MIN:The image of a recording at 1 minute startpoint will be registered.3 MIN:The image of a recording at 3 minutes startpoint will be registered.NOTE:You cannot select the thumbnail image for Video mode.BLACK LEVEL (REC)You can set the black level for when you record.Standard : Records at the level of the inputsource.Enhanced : Lowers the level 7.5IRE and records.The unauthorized recording, use, distribution, orrevision of television programs, videotapes, DVDsand other materials, is prohibited under the Copy-right Laws of the United States and other countries,and may subject you to civil and/or criminal liability. 2J40101A P23-33 3/4/06, 10:43 AM32
33Various settingsSetting the channel / Setting other itemsThis DVD/VCR is equipped with a channel memoryfeature that allows you to skip channels up or downto the next channel set in memory, hence skip overunwanted channels.Before selecting channels, they must be pro-grammed into the DVD/VCR’s memory. In additionto normal VHF and UHF channels, this DVD/VCR canreceive up to 113 Cable TV channels. To use thisDVD/VCR with an antenna, set the TV/CABLE menuoption to the TV mode. When shipped from thefactory, this menu option is in the CABLE mode.Preparation:•Turn ON the TV and set it to the video input mode.•Select “CH SETUP”. For the procedure, see steps 1to 3 in “Using the SETUP MENU” on page 24.TV/CABLE SELECTSelect “TV/CABLE SELECT” and select “TV” or“CABLE”.TV:VHF/UHF channelsCABLE:CABLE TV channelsAUTO CH MEMORYThe VCR can receive a maximum of 181 channels bypresetting the channels into memory.When you select “AUTO CH MEMORY” and pressENTER, the AUTO CH MEMORY function will be acti-vated. The channel display will count up and, when fin-ished, the screen returns to normal.ADD/DELETE (channels)You can add the channels you want or delete the chan-nels you do not want manually.Select “ADD/DELETE” and select “ADD” or “DEL” foreach channel.• Press CH / to select the channel.The numeric keys can also be used for selection.•When you want to delete the selected channel, press to select “DEL” and press ENTER.•When you want to use the selected channel, press to select “ADD” and press ENTER.You can set the switching interval between playedback images in the slide show mode. And, you candisplay the registration code of DivX® VOD.Preparation:•Turn ON the TV and set it to the video input mode.•Select “OTHER”. For the procedure, see steps 1 to 3in “Using the SETUP MENU” on page 24.JPEG INTERVALYou can select the interval time for JPEG slide show(page 47).Select “JPEG INTERVAL” and select the switching in-terval between images from the below.OFF:The slide show mode is not used.5 SEC:The interval is set to 5 seconds.10 SEC:The interval is set to 10 seconds.15 SEC:The interval is set to 15 seconds.DivX® VODThis unit is designed and manufactured to support theDivX® VOD (Video On Demand) DRM (Digital RightsManagement). You can display the registration code ofVOD.TIMER REC SETSYSTEM SETUPAV SETUPREC SETUPCH SETUPOTHERCH SETUPTV/CABLE SELECTAUTO CH MEMORYADD/DELETECABLEPROCEEDPROCEEDSETUP MENURETURNENTER BACK ENDSELECTSETUPENTER 2J40101A P23-33 3/4/06, 10:43 AM33
Disc playback34Playback procedurePreparation:•Turn ON the TV and set to the video input mode.• Press DVD to select the DVD mode. (The DVD indicator will light.)NOTE: It is impossible to switch to the VCR mode while DVD isplayed back.1Press OPEN/CLOSE.The disc tray will open.2Place a disc onto the tray.Hold the disc, position it with theprinted label side up, align it withthe guide and place it in its properposition.3Press OPEN/CLOSE to close thedisc tray.“READING” appears on the screenand some discs start playback au-tomatically.•A menu screen may appear onthe TV screen if the disc has amenu feature. In this case, press, , , or ENTER to operate a menu feature.4Press PLAY to start playback.5Press STOP to end playback.•The DVD/VCR memorizes the stopped point, depending onthe disc. “ ” appears on the screen for approx. 4 seconds.“” keeps blinking in the display window until the playback isstopped completely. Press PLAY to resume playback (from thescene point).•If you press STOP again (“ ” appears on the screen), the DVD/VCR will clear the stopped point.6Then press OPEN/CLOSE.The disc tray opens.Remove the disc and press ON/STANDBY.The disc tray closes automatically and DVD/VCR turns off.NOTES:•If a non-compatible disc is loaded, “IN-CORRECT DISC”, “REGION CODEERROR” or “PARENTAL ERROR” willappear on the TV screen according tothe type of loaded disc. In this case, checkyour disc again (See pages 9 and 26).•Some discs may take a minute or soto start playback.•A prohibition symbol “ ” may appearat the upper right of the screen. Thissymbol means either the feature youtried is not available on the disc, or theDVD/VCR can not access the featureat this time. This does not indicate aproblem with the DVD/VCR.•When you set a single-faced disc la-bel downwards (ie. the wrong way up)and press PLAY or OPEN/CLOSE,“READING” will appear and then it willchange to “NO DISC”.•Some playback operations of DVDsmay be intentionally fixed by softwareproducers. Since this DVD/VCR playsDVDs according to the disc contentsthe software producers designed,some playback features may not beavailable. Also refer to the instructionssupplied with the DVDs.•When playing DTS-encoded AudioCDs, excessive noise will be heardfrom the analog stereo outputs. Toavoid possible damage to the audiosystem, the consumer should takeproper precautions when the analogstereo outputs of the DVD/VCR areconnected to an amplification system.READING 2J40101A P34-40 3/4/06, 10:44 AM34
Disc playback35Playback by selecting a titleWhen playing back a recordeddisc, you can display the titlemenu and select the title to beplayed back.Preparation:•Turn ON the TV and set to the video input mode.•Load a recorded DVD.• Press DVD to select the DVD mode. (The DVD indicator will light.)1Press TITLE MENU.The title menu will appear.If there are many original titles and playlists...Before pressing TITLE MENU, press DVD MENU until “VR ORG”or “VR PL” appear on the upper right of the TV screen, then pressTITLE MENU.The first original title or playlist will be highlighted.2Press or to select the title you want to playback.3Press ENTER.The selected title is played back.NOTES:• If you don’t display the title menu and press PLAY, the first title isplayed back.• The title menu is used not only for playing back titles but also forediting various discs and titles. For details of editing operation, seepage 63.•If you create a playlist, an original title and playlist appear in the titlemenu. For creating a playlist, see page 64.•In case the disc includes more than 9 titles, you can turn to the nextor the previous page. Press , then press or to display next/previous page. To return to normal use, press .•You cannot switch to the VCR mode when the title menu is showing.Press TITLE MENU to clear the title menu, then press VCR to switchto the VCR mode.RETURNPLAY BACKSETENDSELECTTITLEMENUENTERTITLE MENUOriginal titlesPlaylist Thumbnail imageRecording informationDISC NAME:----11/23/2006 08:41AM 006 SLP11/25/2006 10:03PM 011 SP11/29/2006 11:30AM 009 SP12/01/2006 06:52PM 006 XP11/23/2006 08:41AM 006 SLP PLREC DATE :11/23/2006TIME :08:41AMLENGTH :00:30:17CHANNEL :006REC MODE :SLPRETURNPLAY BACKSETENDSELECTTITLEMENUENTERTITLE MENUDISC NAME:----11/23/2006 08:41AM 006 SLP11/25/2006 10:03PM 011 SP11/29/2006 11:30AM 009 SP12/01/2006 06:52PM 006 XP11/23/2006 08:41AM 006 SLP PLREC DATE :11/29/2006TIME :11:30AMLENGTH :00:59:45CHANNEL :009REC MODE :SPNOTE:When a disc that has been recordedin the Video mode is finalized, the titlemenu is automatically changed thatcan be played back even with otherDVD players. Thumbnail image andrecording information will not appearin the title menu after finalizing— — — —1/111/23/2006 08:41AM 006 SLP11/25/2006 10:03PM 011 SPPREVNEXT11/29/2006 11:30AM 009 SP12/01/2006 06:52PM 006 XP11/23/2006 08:41AM 006 SLP PL 2J40101A P34-40 3/4/06, 10:44 AM35
Disc playback36Checking media informationDISC NAME----MEDIA TYPE DVD VIDEOTITLE ORIGINAL35REMAINING TIME----/SPDISC PROTECT NOFINALIZED YESFinalizeDisc protectRemaining time*TitleMedia typeDisc nameVarious information on the loadeddisc can be displayed on the TVscreen.Preparation:•Turn ON the TV and set it to the video input mode.•Load the disc.• Press DVD to select the DVD mode. (The DVD indicator will light.)1Press DISPLAY.Media information will appear.2Press DISPLAY while the media information above is displayed.The next media information will appear.*The remaining time displayed during recording may be differentfrom the actual remaining time. When you want to check the cor-rect remaining time, stop recording and display the media infor-mation again.3Press DISPLAY again while the media information above is dis-played. The media information will disappear.Playback condition (playback, stop, pause and record)The number of audio languages and present languagePlayback elapsed timeCurrentsubtitleslanguageRecording modeThe number of titles and present title numberPresent channelPresent timeThe number of angles and present angle numberThe number of chapters and present chapter numberTITLE 02/02 ORG TIME 00:05:15CHAPTER 01/01 SUBTITLE--/--ANGLE 01/01 REC MODE SPAUDIO 01/01CLOCK 12:00 AM CH 007*If you press DISPLAY during chase playback, the informationscreen is displayed.The symbols indicate that the player is in chase playback.The progress bar shows the current position of playback and theposition of recording. Normally the recording position is shownas being at 100%. Items other than these appear the same as ona normal information screen.Current recordingposition(Fixed at 100%)Current PlaybackpositionNOTES:•The displayed information varieswith the type of media.•Some information may not appeardue to media type or operatingconditions.•In stop mode, some informationdoes not appear. 2J40101A P34-40 3/4/06, 10:44 AM36
Disc playback37Special playbackNOTE: There may be a slight de-lay between pressing the buttonand the function activation.Fast forward playbackPress SEARCH during normal playback.Each press of SEARCH will increase the speed of the search(x2), (x12), (x24), (x100).(The speed of the search is increased up to only 2 steps in Audio CD.)•To resume normal playback, press PLAY.Review playbackPress SEARCH during normal playback.Each press of SEARCH will increase the speed of the search (x2), (x12), (x24), (x100).(The speed of the search is increased up to only 2 steps in Audio CD.)•To resume normal playback, press PLAY.Still playbackPress PAUSE/STILL during normalplayback.• To resume normal playback, pressPLAY.Frame advancePress PAUSE/STILL during still play-back.One frame is advanced each time youpress PAUSE/STILL.•To resume normal playback, pressPLAY.Slow motion playbackPress SLOW during normal playback or still playback.Each press of SLOW will change the speed of the slow “ 1/2”,“1/4” and “ 1/8”.•To resume normal playback, press PLAY.•To resume the still playback, press PAUSE/STILL.Locating a chapter or trackPress SKIP or SKIP during playback to locate a chapter thatyou want to watch.Each time you press the button, a chapter or track is skipped.NOTES:•The unit is capable of holding a still video image or On screen display image on your television screen indefi-nitely. If you leave the still video image or On screen display image displayed on your TV for an extended periodof time, you risk permanent damage to your television screen. Projection televisions are very susceptible.•Fast forward and review playback does not work with a MP3/WMA/JPEG CD.•Frame advance and slow motion does not work with a MP3/WMA/JPEG CD.•When you press SKIP once, playback starts from the beginningof the current chapter or track. If you want to play the preceding chapteror track, press SKIP twice in quick successions. 2J40101A P34-40 3/4/06, 10:44 AM37
Disc playback38Instant skip / Locating a specific sceneInstant skipUse this function to skip commercials while you playback.Press INSTANT SKIP during playback.The time jumps to a point approx. 30 seconds later and playback re-sumes.NOTE:With some DVD-Video, the Commercial skip operation may not work.Locating a specific sceneSpecify the time recorded on the disc, chapter or title to playback.1Press PLAY MODE.The play mode screen will appear.2Press or to select “TIME SEARCH”, “CHAPTER SEARCH”or “TITLE SEARCH”, and press ENTER.TIME SEARCH: Input the time to be played back.CHAPTER SEARCH: Select the chapter number to be played back.TITLE SEARCH: Select the title number to be played back.The screen above shows the display when “CHAPTER SEARCH”is selected.3When selecting “TIME SEARCH”, input the time to be played backwith the numeric keys. When selecting “CHAPTER SEARCH” or“TITLE SEARCH”, press or to select the chapter number ortitle number.4Press ENTER.The playback starts at the point you selected.NOTE:For “REPEAT”, see “Title, Chapter repeat playback” (page 39).TIMESEARCHCHAPTERSEARCHTITLESEARCH REPEATTIMESEARCHCHAPTERSEARCHTITLESEARCH REPEATCHAPTER1CHAPTER2CHAPTER3 2J40101A P34-40 3/4/06, 10:44 AM38
Disc playback39Repeat playbackABA1Press A-B REPEAT during play-back.The start point is selected.2Press A-B REPEAT again.The end point is selected. Playbackstarts at the point that you selected.Playback stops at the end point,returns to point A automatically,then starts again.To resume normal playback press A-B REPEAT again.“OFF” appears on the screen.Title, Chapter repeat playback1Press REPEAT during playback.The play mode screen will appear.2Press or to select “REPEAT” and press ENTER.3Press or to select “OFF”, “CHAPTER” or “TITLE”.OFF: Playback is not repeated.CHAPTER: The chapter is played back repeatedly.TITLE: The title is played back repeatedly.4Press ENTER.To cancel the repeat playback, select “OFF” in step 3.Instant replayThis feature can be used to repeat the last 10 seconds of viewedmaterial, and continues to play as normal.Press INSTANT REPLAY during playback.The video returns to a point 10 seconds before and playback resumes.NOTES:•If the time from the title top is less than 10 seconds when INSTANTREPLAY is pressed, the title top is repeated and then the video isplayed back.•With some DVD-Video, the one touch repeat operation may not work.TIMESEARCHCHAPTERSEARCHTITLESEARCH REPEATOFFCHAPTERTITLETIMESEARCHCHAPTERSEARCHTITLESEARCH REPEATA-B repeat playbackA-B repeat playback allows you to repeat material between twoselected points.NOTES:•Some discs may not work with therepeat operation.•In A-B repeat mode, subtitles nearpoint A or B may not appear.•A-B repeat does not work duringthe Title and the Chapter repeatplayback.•You may not be able to set A-Brepeat, depending on the scenesof the DVD.•A-B repeat, Title repeat and Chap-ter repeat will not work with a MP3/WMA/JPEG-CD and Video CD.•Chapter repeat will not work witha DivX® CD. 2J40101A P34-40 3/4/06, 10:44 AM39
Disc playback40Title selection / DVD menuNOTES:•Depending on the DVD, you maynot be able to select the title, and a“title menu” may simply be calleda “menu” or “title” in the instructionssupplied with the disc.•Depending on the DVD, you maynot be able to resume palyback atthe scene where you pressed TOPMENU/TITLE MENU or DVDMENU.Title selectionTwo or more titles are recorded on some discs. If the title menu isrecorded on the disc, you can select the desired title.1Press TOP MENU/TITLE MENU during playback.The title menu appears on the screen.• Press TOP MENU/TITLE MENU again to resume playback atthe scene where you pressed TOP MENU/TITLE MENU.2Press / or / to select the desired title.3Press ENTER.The playback of the selected title will start.DVD menuSome DVDs allow you to select the disc contents using the menu.When you playback these DVDs, you can select the subtitles lan-guage and soundtrack language, etc. using the DVD menu.1Press DVD MENU during playback.The DVD menu appears on the screen.•Press DVD MENU again to resume playback at the scene whereyou pressed DVD MENU.2Press / or / to select the desired item.3Press ENTER.The menu continues to another screen. Repeat steps 2 and 3 toset the item completely. 2J40101A P34-40 3/4/06, 10:44 AM40
Disc playback41Audio 1/2 Vo. OFF Dolby DigitalKaraoke playbackYou can turn the vocal on or off recorded on the DVD KARAOKE.During DVD KARAOKE disc playback,press AUDIO repeatedly until thedesired setting is selected.Vo. ON : The primary vocal is outputwhen it is recorded on thedisc.Vo. OFF : The primary vocal is notoutput.NOTES :•Some Karaoke discs may not have the vocal on/off function.•The on screen display will disappear after a few seconds.Changing angles / Zooming / Karaoke playbackx2Changing anglesWhen playing back a disc recorded with multi-angle facility, youcan change the angle that you are viewing the scene from.1Press ANGLE during playback.The current angle will appear.2Press ANGLE repeatedly until the desired angle is selected.ZoomingThis unit will allow you to zoom in on the frame image. You canthen make selections by switching the position of the frame.1Press ZOOM during playback.The center part of the image willbe zoomed in.Each press of ZOOM will changethe ZOOM “x2” , “x3” and “x4”.2Press / or / to view a different part of the frame.You may move the frame from the center position to UP, DOWN,LEFT or RIGHT direction.3In the zoom mode press ZOOM repeatedly to return to a 1:1 view“x1”.Angle 1 out of 3NOTES:•Depending on the DVD, you maynot be able to change the angleseven if multi-angles are recordedon the disc.•You can use the Pause, Slow,Search or Skip feature in thezoom mode.•Zoom function does not workwith a DivX® CD and Video CD.•The vocal output feature is usedduring playback of Dolby Digital(multi-channel) recorded DVDKARAOKE discs. This featureallows you to turn off vocal audiotracks, or restore them forbackground accompaniment.•When playing Karaoke, connectappropriate audio equipmentsuch as an amplifier to this unit. 2J40101A P41-47 3/4/06, 10:44 AM41
Disc playback42Changing soundtrack language / Subtitles / To turn off the PBC (VIDEO CD Version 2.0)Audio 1/8 ENG Dolby DigitalAudio 2/8 FRA Dolby DigitalSubtitle OFFSubtitle 1/32 ENGChanging soundtrack languageYou can select the language when you play a multilingual disc.1Press AUDIO during playback.The current soundtrack languagewill appear.2Press AUDIO repeatedly until thedesired language is selected.The on-screen display will disap-pear after a few seconds.SubtitlesTurning the subtitles On and OffWhen playing back a disc recorded with subtitles, you can turnthe subtitles on or off.Press SUBTITLE during playback until“Subtitle OFF” appears.Changing the subtitles languageYou can select the language when playing back a disc recordedwith multilingual subtitles.Press SUBTITLE repeatedly duringplayback until your desired languageappears.The on screen display will disappearafter a few seconds.NOTES:•If the desired language is not heardafter pressing the button severaltimes, the language is not recordedon the disc.•Changing soundtrack or subtitleslanguage is canceled when youopen the disc tray. The initial defaultlanguage or available language willbe heard and seen if the disc isplayed back again.•Depending on the DVD you may beunable to turn on, turn off, or changethe subtitles, even if they arerecorded on the disc. While playingthe DVD, the subtitles may changewhile opening or closing the disctray, or while changing the title.•In some cases, the subtitleslanguage is not changed to theselected one immediately.Audio LR Audio L Audio RAudio 1/2 LR Audio 1/2 RAudio 1/2 LAudio 2/2 R Audio 2/2 LRAudio 2/2 L33333In case of VIDEO CD playbackEach time you press the AUDIO button, the audio type will changeas follows:VIDEO CDS-VCDTo turn off the PBC (VIDEO CD Version 2.0)Press TITLE MENU in the stop mode, then press ENTER. 2J40101A P41-47 3/4/06, 10:44 AM42
Disc playback43Various operations on CDPreparation:•Turn ON the TV and set to the video input mode.• Load the music CD or Video CD.•Press DVD to select the DVD mode. (The DVD indicator will light.)Press TOP MENU/TITLE MENU.The TRACK INFO screen willappear.This section describes the TRACKINFO screen where music CDs orVideo CDs can be played backusing the various operations.TRACK 02TRACK 03TRACK 04TRACK 05TRACK 06TRACK 07TRACK 08TRACK 09TRACK 10TRACK 01TRACK 0100:00:19/00:03:5400:00:19/00:45:28MODE: NORMALREPEAT: OFFTRACK INFOENTERRETURNPLAY BACK ENDSELECT SETTITLEMENUThe elapsed time and total time of the music data (during playback) Scroll barThe elapsed time and total time of the whole CDCurrent playback modeThe track number during playbackThe music data recorded on the CDPress . The menu list will appear.Playing back a selected track1Press or to select the track number you want to playbackand press .2Press or to select “PLAY” from the menu list and press ENTER.The selected track will be played back.Excluding specified track1During stop, press or to select the track number you do notwant to playback and press .2Press or to select “HIDE/SHOW” from the menu list and pressENTER.The selected track will not be played back. (“H” appears at the sideof the track number.)When you want to cancel the exclusion, press or to select thetrack number with “H” and press .Press or to select “HIDE/SHOW” from the menu list and pressENTER, “HIDE” will be canceled.NOTES:•In case the disc includes morethan 10 tracks, you can turn tothe next or the previous page.Press , then press or todisplay next/previous page. Toreturn to normal use, press .•In case of VCD and SVCDplayback, “HIDE/SHOW”,“RANDOM PLAY”, “PROGRAMPLAYBACK” and “TIMESEARCH” will not appear in themenu list.TRACK 02TRACK 03TRACK 04TRACK 05TRACK 06TRACK 07TRACK 08TRACK 09TRACK 10TRACK 01TRACK 0100:00:19/00:03:5400:00:19/00:45:28Mode: NORMALREPEAT: OFFTRACK INFOENTERRETURNENTER BACK ENDSELECTTITLEMENUSETPLAYHIDE/SHOWRANDOM PLAYREPEAT TRACKREPEAT ALLPROGRAM PLAYBACKTIME SEARCHPLAYMenu list 2J40101A P41-47 3/4/06, 10:44 AM43
Disc playback44Various operations on CDNOTE:When recording on a CD-R/CD-RWin the MP3 or WMA modes, “RAN-DOM PLAY” and “TIME SEARCH”will not appear in the menu list.Random playback1Press or to select “RANDOM PLAY” from the menu list andpress ENTER.The order of music tracks is randomly changed.2Press PLAY.Music is played back in random order.To cancel random playback, select “RANDOM PLAY” from the menulist again, and press ENTER.Repeat playback of selected track1Press or to select the track number you want to repeatplayback and press .2Press or to select “REPEAT TRACK” from the menu list andpress ENTER.3Press PLAY.The selected track will be played back repeatedly.To cancel repeat track playback, select “REPEAT TRACK” from themenu list again, and press ENTER.Repeat playback of all tracks1Press or to select “REPEAT ALL” from the menu list andpress ENTER.2Press PLAY.All tracks on CD will be played back repeatedly.To cancel the repeat all playback, select “REPEAT ALL” from the menulist again, and press ENTER.Playing back programsYou can specify the playback order yourself.1Press or to select “PROGRAM PLAYBACK” from the menulist and press ENTER.2Press or to select the track number that you want to changethe order of and press ENTER.The “ ” mark will appear at the right side of the track number.3Press or to select to the track number that you want tospecify and press ENTER.The track number that you select in step 2 moves to the positionthat you specified.4Repeat steps 2 and 3 to change the playback order.5Press PLAY.The tracks will be played back in the changed order.To cancel program playback, select “EXIT PROGRAM MODE” fromthe menu list and press ENTER.Playing back track by specifying the time1Press or to select “TIME SEARCH” from the menu list dur-ing playback and press ENTER.2Press / or / to specify the elapsed time of the track (thiswill be the starting point of playback) and press ENTER.Playback will start from the specified elapsed time. 2J40101A P41-47 3/4/06, 10:44 AM44
Disc playback45MP3/WMA/JPEG/DivX® playbackMP3 and WMA files can be playedback. You can also display JPEG/DivX® files on the TV screen andenjoy them.Some discs may not play due tothe condition of the recording.Limitations on MP3/WMA/JPEG/DivX® CD playback:•MP3/WMA/JPEG/DivX® CD is adisc that is standardized byISO9660.•The folder and file names of theMP3/WMA/JPEG/DivX® CD mustcorrespond to the ISO standard-ized file names.•This unit can read 200 files perfolder. If one folder has more than200 files, it reads up to 200 files,the remaining files will be omitted.•If the CD has both audio tracks andMP3/WMA/JPEG/DivX® files, onlyaudio tracks are played.•It may take more than one minutefor this unit to read MP3/WMA/JPEG/DivX® files depending on itsstructure.•Music recorded by “Joliet Record-ing Specification” can be playedback. Long file names will be cut.•The music files recorded by “Hier-archical File System ” (HFS) can-not be played.•The MP3/WMA/JPEG/DivX® filesrecorded on DVD disc cannot beplayback.Preparation:•Turn ON the TV and set to the video input mode.•Load the disc storing MP3, WMA, JPEG or DivX®.•Press DVD to select the DVD mode. (The DVD indicator will light.)Using the BROWSER screen1Press TITLE MENU.The BROWSER screen will appear.2The MP3, WMA, JPEG and DivX® files and folders stored in thedisc are displayed on the BROWSER screen.•Select a folder and press ENTER. The files in the folder appear.When the file to be displayed is selectedYou can select the file types to be displayed on the BROWSER screen.1Press to select “SELECT FILES” and press ENTER.The following list will appear.popArtGrammy03_01.mp3Grammy03_02.mp3Grammy03_03.mp3Grammy03_04.mp3Grammy03_05.mp3Grammy03_06.mp3Grammy03_07.mp3Grammy03_08.mp3Toulouse-LautrecBROWSERENTERRETURNENTER BACKSETENDSELECTTITLEMENUMUSIC ONLY: Only MP3 and WMA files appear.PICTURES ONLY: Only JPEG files appear.MOVIE ONLY: Only DivX® files appear.ALL: All files and folders appear.2Select one item in the above list and press ENTER.The display will be changed to the selected display type.PLAYSELECT FILESBROWSERENTERRETURNENTER BACK ENDSELECTTITLEMENUMUSIC ONLYMUSIC ONLYPICTURES ONLYMOVIE ONLYALLSETpopArtGrammy03_01.mp3Grammy03_02.mp3Grammy03_03.mp3Grammy03_04.mp3Grammy03_05.mp3Grammy03_06.mp3Grammy03_07.mp3Grammy03_08.mp3Toulouse-Lautrec 2J40101A P41-47 3/4/06, 10:44 AM45

Navigation menu