Ohsung Electronics B526A Remote Controller User Manual H User s Manual

Ohsung Electronics Co., Ltd. Remote Controller H User s Manual

User Manual

Order Number : GETEC-C1-17-532 FCC Part 15 subpart C Test Report Number : GETEC-E3-17-052 Page 1 / 1 EUT Type: Remote Controller FCC ID.: OZ5B526A APPENDIX H : USER’S MANUAL
B526A Manual Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA Page 1/ 9 TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.com/ 1 - Mechanical Requirements 1.1 - Design - Dimensions : 160 x 47 x 17.8mm TOP CASE MATERIAL ABS MATERIAL COLOR BLACK PRINT COLOR SMI-G 715 (BLACK) BOTTOM CASE BATTERY COVER MATERIAL ABS MATERIAL COLOR BLACK RUBBER BUTTON MATERIAL SILICONE RUBBER FORMING COLOR BLACK FORMING COLOR 4-A TRANSLUCENT CLEAR PRINTING COLOR WHITE SURFACE TREATMENT SILICONE COATING
B526A Manual Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA Page 2/ 9 TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.com/ 1.2 - Picture (for reference only)
B526A Manual Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA Page 3/ 9 TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.com/ 1.3 - Batch Number Adhesive label is attached at the inside part of the battery cover 1.4 - Packing 1.4.1 - Packing Process - PE bag dimensions : 83 x 286 mm (LDPE 0.05t) - Quantity Per Box: 140pcs - Box dimensions : W 600 x D 400 x H 200 mm 1.4.1 - Palett definition - Pallet dimension : W 1200 x D 800 x H 170 mm - Full pallet dimension : W 1200 x D 800 x H 1770 mm - Quantity per pallet : 4,480pcs (4 boxes / layer - 8 layers)
B526A Manual Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA Page 4/ 9 TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.com/ 2 - Electrical Requirements 2.1 - Electrical Characteristic Parameter Condition Spec Unit Frequency Range Bluetooth Low Energy Specification 2.402 ~ 2.480 [GHz] Channel 40 [Num] RF Power 0 [dBm] Test channel TC-3000 (RF measuring instrument) 19 [Num] RF Power PAvg 0±1 [dBm] PMax +1 [dBm] Pmin -1 [dBm] Modulation Characteristics ∆f1 avg 225~275 [KHz] ∆f2 avg ≥ 185 [KHz] ∆f2/∆f1 0.8 ∆f2min ≥ 92.5 [KHz] ∆f2rate ≥ 99 [%] Carrier Frequency Offset and Drift fTx-fn ≤ 150 [KHz] ∆f0-fn ≤ 50 [KHz] f1-f0 ≤ 20 [KHz] ∆fn-f(n-5) ≤ 20 [KHz] Operating Voltage RF (Bluetooth) 2.0~3.6 [V] LVI Voltage Low Voltage Indicate 2.25 ± 0.2 [V] Operating current (IR) Power: 3V ≤35 [mA] Operating current (RF KEY) Power: 3V Non-directional distance ≤12 [mA] Operating current (RF+Voice) ≤25 [mA] Leakage current ≤10 [㎂] RF range (distance) ≥10 [m] IR Range Direct 12 [m] Horizontal 7 (±30°) [m] VOICE 300Hz Voice Inspection JIG -15 ~ -5 [dB] 2KHz -21 ~ -2 [dB] 3.8KHz 20 ~ 0 [dB] - Hardware Version: V1.0
B526A Manual Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA Page 5/ 9 TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.com/ 3 - Software Requirements 3.1 - Bluetooth 4.2 LE identification a) Device Name: Channel Master Remote b) Vender ID: 0x02AF c) Product ID: 0x2025 d) Software Version : V0007 3.2 - Pairing mode a) At first time pairing or after Factory Reset, RCU works only in IR. b) Press [OK] and [APPS] keys for longer than 4 seconds. LED stays ON while pressing [OK] and [APPS] keys. c) After 4 seconds, the LED starts blinking so that to confirm the remote has entered into pairing mode. d) After RCU has entered pairing mode, RCU can send the IR signal of Up, Down, Left, Right and OK keys. e) If pairing is successfully made, the LED goes OFF and remote starts working in Bluetooth. f) If the user presses any key during pairing mode, the remote stops pairing and goes back to IR mode, excepted Up, Down, Left, Right and OK keys. g) If pairing is not successfully made for 90 seconds, the LED goes ON for 4 seconds and then goes OFF. The remote stops pairing and goes back to IR mode if first time pairing and after Factory Reset. 3.3 - Re-pairing mode a) Press [OK] and [APPS] keys for longer than 4 seconds. LED stays ON while pressing [OK] and Google [APPS] keys. b) After 4 seconds, the LED starts blinking so that to confirm the remote has entered into pairing mode. c) After RCU has entered pairing mode, RCU can send the IR signal of Up, Down, Left, Right and OK keys.
B526A Manual Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA Page 6/ 9 TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.com/ d) If pairing is successfully made, the existing pairing table is deleted, the LED goes OFF and the remote works in Bluetooth with the new device. e) If the user presses any key during pairing mode, excepted Up, Down, Left, Right and OK keys, the remote stops pairing and the previous paired status is restored, f) If pairing with new device is not successfully made for 90 seconds, the LED goes ON for 4 seconds and then goes OFF. The previous paired status is restored. 3.4 - Factory Reset mode a) Press [APPS] and [0] keys for longer than 4 seconds. LED stays ON while pressing [APPS] and [0] keys. b) The remote blinks 3 times to confirm that it is deleting the existing pairing table and TV & Audio IR setting. c) When Factory Reset is completed, LED goes OFF and the remote works in IR mode. 3.5 - IR backup in paired mode a) If, for any reason, the RF connection is lost, the remote sends the IR code of the corresponding pressed key. b) The remote tries to reconnect for sending the RF code. 3.6 - Voice Search initiated by the remote a) For Voice function, it is recommended to be within 5 meters from the receiver. b) Distance between mouth and microphone should be within 40 cm (15~20cm recommended). c) Microphone key pressed and released, remote sends “key pressed event, key released event” to the STB and the STB sends back the START command to the remote. d) The LED starts blinking, the remote transmits the voice data for 10sec timeout duration. e) After timeout duration, the remote stops transmitting the voice data and the LED is turned off. f) Or When the remote receive the stop command from STB, thre remote stops transmitting the voice data and the LED is turned off.
B526A Manual Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA Page 7/ 9 TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.com/ Note: if any key is pressed within the timeout duration, the remote stops transmitting the voice data and activate the pressed key event. 3.7 - Voice Search initiated by the launcher a) For Voice function, it is recommended to be within 5 meters from the receiver. b) Distance between mouth and microphone should be within 40 cm (15~20cm recommended) c) User selects and validates the voice search on the launcher by using navigation and OK keys. d) STB sends the voice search START command to the remote. e) After timeout duration, the remote stops transmitting the voice data and the LED is turned off. f) Or When the remote receive the stop command from STB, thre remote stops transmitting the voice data and the LED is turned off. Note: if any key is pressed within the timeout duration, the remote stops transmitting the voice data and activate the pressed key event. 3.8 – Setup for TV & Audio a) As long as the RCU is paired to the STB, the RCU can then automatically be set up by the STB for TV or Audio control. b) The STB can set the RCU’s IR using the command defined in Appendix1. c) When the setting is completed, the Volume key and the Power key output the IR signal according to the set value. d) If the RCU receives the “send keycode” command, it outputs the IR signal of the corresponding key. However, the RCU will not store the set value. e) The TV database uses the set number from 0001 to 1999. f) The Audio database uses the set number from 3001 to 4999 3.9 – Remove the TV & Audio a) Press [OK] and [V-] keys for longer than 4 seconds. LED stays ON while pressing [OK]
B526A Manual Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA Page 8/ 9 TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.com/ and [V-] keys. b) After 4 seconds, LED will be blink 3 times. c) Press 01 to remove the TV setting. Or press 02 to remove the Audio setting. d) LED will be blink 3 times to confirm the remote has remove the setting. 3.10 - Couch mode a) If a key or multiple keys are pressed continuously for more than 30s, the remote stops transmission (except pairing combination) in order to protect the battery discharge. 3.11 - OAD mode a) OAD proceeds according to the RTK specification. 3.12 - Key codes a) In Bluetooth mode, HID Profile is used. b) In IR Mode, NEC format is used - Structure of the NEC format: Custom1 - Custom2 – Data – Inverse data For MUTE to be seen as 0x16-0x20-0x25. Another alternative is 0x1620-0x25 Custom1: 0x16 Custom2: 0x20 c) Code list is detailed in Table 1 Key Code Name Event constant name IR Code (Data) HID Usage Page Usage ID Info KEYCODE_PROG_GREEN 0xA6 0x07 0x006A Power KEYCODE_POWER 0x21 0x0C 0x0030 D-pad up KEYCODE_DPAD_UP 0x15 0x0C 0x0042 D-pad down KEYCODE_DAPD_DOWN 0x16 0x0C 0x0043 D-pad left KEYCODE_DPAD_LEFT 0x17 0x0C 0x0044 D-pad right KEYCODE_DPAD_RIGHT 0x18 0x0C 0x0045 D-pad center KEYCODE_DPAD_CENTER 0x19 0x0C 0x0041 Back KEYCODE_BACK 0x48 0x0C 0x0224 Guide KEYCODE_SELECT_PROGRAM_GUIDE 0xC0 0x0C 0x008D APPS KEYCODE_HOME 0x47 0x0C 0x0223 Volume + - - - -
B526A Manual Address : #181 GONG DAN-DONG, GUMI, GYEONG BUK, KOREA Page 9/ 9 TEL : 82-54-468-7063 / FAX : 82-54-461-8368 http://www.ohsungec.com/ Volume - - - - - DVR KEYCODE_MEDIA_SELECT_HOME 0xA0 0x0C 0x009A Channel + KEYCODE_CHANNEL_UP 0x33 0x0C 0x009C Channel - KEYCODE_CHANNEL_DOWN 0x34 0x0C 0x009D Rewind KEYCODE_MEDIA_REWIND 0x51 0x0C 0x00B4 Play/Pause KEYCODE_MEDIA_PLAY_PAUSE 0x52 0x0C 0x00CD Fast Forward KEYCODE_MEDIA_FAST_FORWARD 0x53 0x0C 0x00B3 1 KEYCODE_1 0x01 0x07 0x001E 2 KEYCODE_2 0x02 0x07 0x001F 3 KEYCODE_3 0x03 0x07 0x0020 4 KEYCODE_4 0x04 0x07 0x0021 5 KEYCODE_5 0x05 0x07 0x0022 6 KEYCODE_6 0x06 0x07 0x0023 7 KEYCODE_7 0x07 0x07 0x0024 8 KEYCODE_8 0x08 0x07 0x0025 9 KEYCODE_9 0x09 0x07 0x0026 0 KEYCODE_0 0x0A 0x07 0x0027 ● KEYCODE_.and >4 0xA1 0x07 0x0037 Microphone KEYCODE_SEARCH 0x46 0x0C 0x0221 Table 1: Code list 3.13 - Battery level a) RCU sends the information for battery level using Bluetooth battery service. b) Level of LVD is 2.25V ±0.2V. c) If the battery voltage as reached the LVD value, RCU cannot enter the pairing mode. d) If the battery voltage is under 2.0V, RCU does not operate. e) When the battery voltage is 2.1V or more, the RCU operates again. 4 - EMC Conformity Assesment of compliance of the product to the requirements relating to Electromagnetic Compatibility is based on the following standards: 4.1 – FCC : FCC Part 15 Subpart C 15.247 4.2 – IC : RSS-210, RSS-247 4.3 – Mexico : IFETEL, NOM
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. Note : The manufacturer is not responsible for any Radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment. FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. End users must follow the specific operating instructions for satisfying RF exposure compliance. Industry Canada(IC) Statement [English] Statement This device complies with Industry Canada’s License-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Industry Canada Statement (For Canada) This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. IC Radiation Exposure Statement (For Canada) This equipment complies with IC radiation exposure limits set forth for an Uncontrolled environment.

Navigation menu