Ohsung Electronics NGIHKR Remote controller User Manual Microsoft PowerPoint NGI Manual 2014 04 17 1
Ohsung Electronics Co., Ltd. Remote controller Microsoft PowerPoint NGI Manual 2014 04 17 1
Users Manual
Hard-key definitions NGI HKR
The
controller
have
the following
hard
-
keys as shown below:
NGI HKR Manual
Specification of NGI HKR
The controller
support
Bluetooth
for
user command functions
FCC ID: OZ5NGIHKR
The
controller
have
the
following
hard
keys
as
shown
below:
1
UP
The
controller
support
Bluetooth
for
user
command
functions
.
1) Bluetooth Version : 2.0
2) Power Class : Class 2
3) Supported Profiles : AVRCP, IOPT
4)
Power
Suppy
: DC +3 0V 2 X AAA Cells
1
–
UP
2 – DOWN
3 – LEFT
4 – RIGHT
5
–
DVD MENU
4)
Power
Suppy
:
DC
+3
.
0V
,
2
X
AAA
Cells
5) Illumination : LED Backlight
6 – REAR ENVIRONMENT
7 – FAVOURITES
8 – OK
9 – SOURCE
10
–
HELP/SETTINGS
10
HELP/SETTINGS
11 – POWER
12 – VOL +
13 – VOL –
14 – PLAY/PAUSE
15
FWD
15
–
FWD
16 – REWD
17 – LEFT SELECT
18 – RIGHT SELECT
19 – HOME
20 – CABIN AUDIO
21 – BACK
Pairing
1) User
enters
"
Rear Media Settings
"
as shown below:
2) User
selects
"
Pair Remote Control
"
as shown below:
NGI HKR Manual FCC ID: OZ5NGIHKR
1)
User
enters
Rear
Media
Settings
as
shown
below:
2)
User
selects
Pair
Remote
Control
as
shown
below:
3) Display shows the below screen instructing the user
to press and hold the power button for 7 seconds. 4) On successful pairing, the display shows Remote found
as shown below:
5) If a remote control is already paired to the system, the
NGI HKR Manual
Failed Pairing
FCC ID: OZ5NGIHKR
display shows below screen, asking for confirmation to
proceed (or not): Should the pairing process fail, the display shows the
below screen, prompting the user to retry or cancel.
NGI HKR Manual
Low Battery Warning
Batter
y
level warnin
g
s are
g
iven b
y
the AVRCP
p
rotocol to the ISC. There are two levels of batter
y
warnin
g
g
iven to the user
FCC ID: OZ5NGIHKR
yggyp
ygg
indicating that the batteries are 1) getting low (a standard warning) and 2) they need replacing (critical warning).
The attached HMI images show the intent (exact wording may change as these screens have not been finalised):
NGI HKR Manual
FCC Information to User
FCC ID: OZ5NGIHKR
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or
that
interference
will
not
occur
in
a
particular
installation
.
If
this
equipment
does
cause
harmful
interference
to
radio
or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver
•
Increase
the
separation
between
the
equipment
and
receiver
.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is con-nected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution
Modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
FCC Compliance Information : This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received,two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE
PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.