Ohsung Electronics URC100 RF Transmitter Universal Remote Control User Manual

Download:
Mirror Download [FCC.gov]
Document ID	339059
Application ID	uuJ4KZnVZgp76Jjd/spmxQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	30.25kB (378138 bits)
Date Submitted	2003-07-10 00:00:00
Date Available	2003-07-10 00:00:00
Creation Date	2003-07-08 14:37:19
Producing Software	Acrobat 5.0 Scan Plug-in for Windows
Document Lastmod	2003-07-08 14:37:36
Document Title	Users Manual
Document Creator	Acrobat 5.0 Scan Plug-in for Windows

URc Proprietary II
2. PROGRAMMING THE REMOTE CONTROL
Programming of the remote control to control a particular device shall be accomplished by either of two methods:
- Entering a three—digit device code
0 Using a search method
The remote control can operate up to eight separate audio and video devices. To program the remote control for
your device, use the following steps:
2.1 PREPROGRAMMED SET UP
2.1.1 Entering a Three-Digit Device Code
1. Turn on the device you wish to operate manually,
2, Find the three digit Set-Up code number for your device from the code tables.
Press the matching [DEVICE] button (AUD, CD, DVD, AUX, SAT, TV, VCR or CBL) and [MUTE] button
simultaneously. The SET will appear in the LCD. SET appears in the LCD for 20 seconds to indicate that the
remote control is ready to be programmed. The following steps must be entered while SET appeai's in the LCD.
4. Point the remote control toward the device and press the three digit code number for that device using the
number buttons (0—9) on the remote control SET followed by the number will appear in the LCD. Your device
will turn off when the correct Set-Up Code number has been selected. If the device does not turn off, press in
the next Set-Up Code number from the list.
5. Once the device turns off, press the [DEVICE] button selected in the step 3 once again to store the Set-Up Code
number. PASS will blink and display the device name.
Note. Test the remote control for your device. Try the POWER, Channel Up and Down, Volume Up and Down
buttons, etc. If any of the buttons do not perform as they should, please repeat the set-up from Step 1 using the next
Set-Up code number for your device.
6. Please repeat the above steps to program the remote control for each of your other devices.
2.1.2 Using the Auto Search Method
Turn on the device you wish to operate manually.
2. Press the matching [DEVICE] button (AUD, CD, DVD, AUX, SAT, TV, VCR or CBL) and [MUTE] button
simultaneously. The SET will appear in the LCD. SET appears in the LCD for 20 seconds to indicate that the
remote control is ready to be programmed. The following steps must be entered while SET appears in the LCD.
3. Point the remote control toward the device and press the [CH +] button on the remote control. Each button
press sends the signal for one Set-Up Code number. Keeping the [CH +] button pressed produces a quick
seaming of the Set-Up Code numbers Release the [CH +] button as soon as the device turns off. Please
Note. If you pass the correct Set-Up Code number, you can retum to it by pressing the [CI-I —] button, one Set-Up
Code number at a time, until your device turns back on.
4. Once the correct code is confirmed, press the [DEVICE] button to store the Set-Up Code number. PASS will
blink and display the device name.
5. Please repeat the above steps to program the remote control for each of your other devices.
No.
URC-l 00
Rev.
URC Proprietary II 1 7
Form E75; Universal mm Count. the
URC Proprletary II
2.1.3 Programming a Second Devlce to Other Device Buttons
This feature is used to program the remote control for two or more TVs, VCRs, etc, or to program a device into a
mode with a different Device Button name. You can store the three-digit Set-Up Code number for any device into
any other Device button.
Example: If your home entertainment system contains two TVs. First, using the TV Device button, program the
remote via standard set-up to operate the first TV. Then, program your second TV into the AUX Button that is not
being used.
It Turn on the device [TV] you wish to operate manually.
2. Find the three-digit Set-Up code number for your device [TV] from the code tables.
3. Press the DEVICE button [AUX] that you will assign for the device and [MUTE] button simultaneously.
The SET will appear in the LCD. SET appears in the LCD for 20 seconds to indicate that the remote
control is ready to be programmed The following steps must be entered while SET appears in the LCD
4. Point the remote control toward the device [TV] and press the three digit code number for that device [TV]
. using the number buttons (0-9) on the remote control. SET followed by the number will appear in the LCD. -
Your device [TV] will turn off when the correct Set—Up Code number has been selected If the device does
not turn off, press in the next Set-Up Code number from the list.
5. Once the device turns off, press the DEVICE [AUX] button selected in the step 3 once again to store the
Set-Up Code number. PASS will blink and display the device name.
2.1.4 identifying the Set Up Code Number
To display the three-digit code number that was stored for a device.
1, Press the [DEVICE] button (AUD, CD, DVD, AUX, SAT, TV, VCR or CBL) and [MUTE] button
simultaneously. The SET will appear in the LCD. SET appears in the LCD for 20 seconds to indicate that
the remote control is ready to be programmed. The following steps must be entered while SET appears in
the LCD.
2. Press [INFO] button. The LCD will blink the Device button name twice and then display the three digit
number that was stored for your device in that mod
2.2 LEARNING SET UP
The remote control has the ability to learn new functions from your original remote controls:
Notel All buttons in all device modes can learn, except the [LIGHT] and [SHIFT] buttons.
Note2. The 8 device buttons at the top of the remote control labeled (AUD, CD DVD, AUX, SAT, TV, VCR or
the [SHIFT] and then press a [DEVICE] button.
Note3. The [RECORD] button can be learned in all device modes by pressing the [SHIFT] and then press [STOP]
button The [SHE-7T] button function is not applied to other buttons except the specified buttons above in the
Learning Set Up mode.
Note3. Leamed functioned override any existing preprogrammed functions on the remote control.
Note4. Learned functions are automatically erased when a new function is learned on the same button.
No.
U'RC- l 00
Rev.
URC Progietaiy II 1
Farm E75a Universal Remote Gotml. Inc
2.2. 1
2.2.2
5.
URC Proprietary lI
Learning New Function on the Remote
Place the URC-lOO and the original remote control to be learned from, on a flat surface. Line up the remote
controls head to head, about 2 to 3 inches apart.
Press and hold the [DEVICE] button (AUD, CD, DVD, AUX, SAT, TV, VCR or CBL) you wish to learn
and [SEL] button simultaneously for about three seconds, until the LCD shows LEARN. The remote is
now in the learning mode.
Note: Each of the following steps must be completed within 20 seconds. If the remote does not receive any new
commands with in the allotted time, it will return to its normal operating mode.
3.
Press and release a button on the URC~100 you have selected to learn the new function The LCD will
show READY.
Press and hold the button on the original remote control for about 2 seconds from which you are learning
the new function. The LCD will show -»-- indicating that it is receiving the information fiom the original
remote control.
Release the button on the original remote control. The [CD will show RETRY.
Press and hold the same button on the original remote once again, for about 2 seconds The LCD will flash
GOOD and then return to LEARN verifying that the new function has been stored. Repeat Steps 3 through
6 for any other buttons you wish to learn new functions.
Once you have completed the lean-ring for all desired buttons in a device mode, store the learned functions
by pressing the [DEVICE] and [SEL] buttons simultaneously, once again. The LCD will show SAVED and
then return to the current device mode.
Note: If the LCD shows FAHc at any time during the lean-ring process, the remote was unable to learn the new
functions. Please repeat from Step 3.
Erasing Learned Functions
To erase learned functions, please refer to the following procedures:
2.2.2.1 Erasing Individual Buttons:
1.
2.
Press the [DEVICE] button for the mode where the learned function has been stored.
Press and hold the [DEVICE] and [SEL] buttons simultaneously for about three seconds, until the LCD
shows LEARN. The remote is new in the learning mode
3. Press and release the button to be erased. The LCD will show READY.
Press the [SHIFT] button. The LCD will flash ERASE, CLEAR, the device name and then return to
LEARN. Repeat Steps 3 and 4 for any other buttons to be erased.
To return to the normal operating mode, press the [DEVICE] and [SEL] buttons simultaneously.
2.2.2.2 Erasing All Buttons In One Devlce Mode:
1.
Press the [DEVICE] button for the mode where the learned function has been stored.
Press and hold the [DEVICE] and [SEL] buttons simultaneously for about three seconds, until the LCD
shows LEARN. The remote is now in the learning mode.
Press and hold the [DEVICE] and [SHIFI] buttons simultaneously for five seconds until the LCD will
flash ERASE. The LCD will flash ERASE 10 times and then alternately CLEAR and the Device Mode.
No.
U'RC-l 00
Rev.
URc Proprietary II 1
Form E75a
universal Rennie Conml. Inc.
URc Proprletary ll
2.2.2.3 Erasing All Buttons In All Devloe Modes
1. Press and hold the [TV] and [SHIFT] buttons simultaneously for ten seconds until the LCD will flash
ERASE, The LCD will flash ERASE 10 times and then flash CLEAR and then return to the TV Device
Mode.
Note: When the LCD on the remote retums to TV, all the learned functions in all eight devices mode have been
erased. All the buttons in all device modes will now operate with the preprogrammed functions in their
respective modes.
2.3 PUNCH THROUGH
2.3.1 Volume Control “Punch Through"
You can program the remote control so that either the AUDIO or TV volume control (Volume Up, Down and
MUTE) will also operate in other modes on the remote control.
Example: If you want to operate Volume control of Audio receiver while remote control is in the Satellite model
1. Select the mode [SAT] that you wish to program for Volume Control “Punch Through”. *
2. Press the corresponding DEVICE button [SAT] and [MUTE] buttons simultaneously. The SET will appear
in the LCD. SET appears in the LCD for 20 seconds to indicate that the remote control is ready to be
programmed. The following steps must be entered while SET appears in the LCD.
3. Press the [SHIFT] button. PUNCH will appear in the LCD.
4. Press the [VOL UP] button. VOL will appear in the LCD.
5, Press the [AUDIO] device button to set-up for Audio volume control. AUDIO will blink in the LCD.
2.3.2 Channel Control “Punch Through”
You can program the remote control so that either the SAT or Cable Channel Controls (CI-I Up and Down) will also
operate in other modes on the remote control.
Example: Change Channel Up and Down on your Cable box while the remote is in the TV mode.
1. Select the mode [TV] that you wish to program for Channel Control "Punch Through”.
2. Press the corresponding DEVICE button [TV] and [MUTE] buttons simultaneously. The SET will appear
in the LCD. SET appears in the LCD for 20 seconds to indicate that the remote control is ready to be
programmed. The following steps must be entered while SET appears in the LCD.
3. Press the [SHIFT] button. PUNCH will appear in the LCD.
4. Press the [VOL Down] button. CH will appear in the LCD.
mmmmnm-. | r - I-Y-‘mi'mll!
2.3.3 Transport Control “Punch Through"
You can program the remote control so that either the DVD or CD Transport Controls (Play, Stop, FF, Rewind,
Pause and Record) will also operate in other modes on the remote control.
Example: Control DVD functions while the remote is in the TV mode.
1. Select the mode [TV] that you wish to program for Transport Control “Punch Through”.
No.
URC-IOO
Rev.
URC Proprietary II 1
Fovm E759 Unlversal Remote Control. Irv;
URC Proprletary II
2. Press the corresponding DEVICE button [TV] and [MUTE] buttons simultaneously. The SET will appear
in the LCD. SET appears in the LCD for 20 seconds to indicate that the remote control is ready to be
programmed The following steps must be entered while SET appears in the LCD.
3. Press the [SHIFT] button. PUNCH will appear in the LCD.
4. Press the [PLAY] button. PLAY will appear in the LCD.
5. Press the [DVD] device button to set»up for DVD Transport control. DVD will blink in the LCD.
2.3.4 VOD Control “Punch Through”
You can program the remote control so that either the Cable or Satellite VOD Controls (Menu, Guide, Info, Exit,
Select, Up, Down, Lefi, Right) will also operate in other modes on the remote control.
Example: Control Cable VOD functions while the remote is in the TV mode.
1. Select the mode [TV] that you wish to program for Transport Control “Punch Through”.
2. Press the corresponding DEVICE button [TV] and [MUTE] buttons simultaneously. The SET will appear
in the LCD. SET appears in the LCD for 20 seconds to indicate that the remote control is ready to be
programmed. The following steps must be entered while SET appears in the LCD.
3. Press the [SHIFT] button. PUNCH will appear in the LCD.
4. Press the [GUIDE] button. VOD will appear in the [CD
5. Press the [CABLE] device button to set-up for Cable VOD control. CABLE will blink in the LCD.
2.3.5 Power Control “Punch Through"
You can program the remote control so that either the TV or Audio Power Controls (Power On and Off) will also
operate in other modes on the remote control.
Example: Control Cable Power function while the remote is in the TV mode.
1. Select the mode [TV] that you wish to program for Power Control “Punch Through".
2. Press the corresponding DEVICE button [TV] and [MUTE] buttons simultaneously. The SET will appear
in the LCD. SET appears in the LCD for 20 seconds to indicate that the remote control is ready to be
programmed. The following steps must be entered while SET appears in the LCD.
Press the [SHIFT] button. PUNCH will appear in the LCD.
4. Press the [Power ON] button. Power will appear in the LCD.
5, Press the [CABLE] device button to set-up for Cable Power function. CABLE will blink in the LCD.
2.4 MACRO MEMORY BUTTONS
'j There are ten memory‘buttons Power On, 6in andTDevrce buttons) that are designed to store up toil?) commands
in each button. You can program up to 30 commands on the 8 Device buttons in AUDIO mode and you can
program up to 30 commands on the Power On and OFF buttons in each 8 modes.
2.4.1 Programming Memory Buttons
Example: To program Memory button, POWER ON, in the Audio mode to send the following commands: to turn
on the AUDIO receiver, turn on the TV, turn on the VCR and tum on the Satellite receiver.
No.
URC-IOO
Rev.
URC Proprietary II 1
Form E75a Universal Remote 0am Inc.
URC Proprietary u
1. Press the corresponding DEVICE button [AUD] and MUTE button simultaneously. The SET will appear
in the LCD. SET appears in the LED for 20 seconds to indicate that the remote control is ready to be
programmed. The following steps must be entered while SET appears in the LCD.
2. Press the [POWER ON] button. M1—ti# will appear in the LCD.
Press the [AUDIO] device button and then press the [POWER ON] button (to turn on the AUDIO). Ml »01
will appear in the LCD.
4. Press the [TV] device button and then press the [POWER ON] button (to turn on the TV). Ml-02 will
appear in the LCD.
5. Press the [VCR] device button and then press the [POWER ON] button (to turn on the VCR). M1-03 will
appear in the LCD.
6. Press the [SAT] device button and then press the [POWER ON] button (to turn on the Satellite). M1-04
will appear in the LCD.
7. Press the [Channel Up] button to store your selections. SAVE will flash two times in the LCD.
Notel: Pressing the [PAUSE] button during the macro programming will add a time delay of 0.2 seconds between
the commands;
Note2: Press & Hold function: Pressing the [PAUSE] button before the macro programming will make that the
remote will send out the macro commands when the button is pressed for 1 second.
2.4.2 Erasing Memory Buttons
1. Press the corresponding DEVICE button [AUD] and [MUTE] button simultaneously. The SET will appear
in the LCD. SET appears in the DCD for 20 seconds to indicate that the remote control is ready to be
programmed. The following steps must be entered while SET appears in the LCD.
2. Press the [POWER ON] button. M1 -# will appear in the LCD.
3. Press the [Channel Up] button. SAVE will flash two times in the LCD.
2.5 CHANGING THE LCD DISPLAY
You can change the display for each Device name of the remote control. To change the AUDIO device name:
1. Press the [AUDIO] device button and [ENTER] button simultaneously for three seconds. The EDIT will
appear in the LCD and then “A” character of AUDIO will blink in the LCD.
2. Select the character using the number pad on the remote control. The characters assigned to each number
pad button are shown below. It will be rotated to a different character each time the same number pas is
pressed.
#1:A B C, 1.
we: D, E, F, 2
m: G, H, l, 3
#4: J, K, L, 4
#5: M, N, 0, 5
#6: P, Q, R, s
#7: s, T, U, 7
No.
URC-l 00
Rev.
URC Proprietary II 1
Fem! E753 Unlvetsal Remote Control. Inc.
URC Proprletary II
#8: V, W, X, 8
#9: Y, Z, 9
#0: #, &, 0
Note: You can move the cursor lefi or right by using the [CURSOR LEFT] and [CURSOR RIGHT] buttons
You can also erase a current character by pressing the [CURSOR DOWN] button.
3. Press the {ENTER} button to save the display you changed SAVE will blink two times in the LCD,
2.6 BACK LIGHT
All the buttons and the LCD on the remote are back light for 10 seconds when the LIGHT button is pressed. The
back light is extended a 11 additional 10 seconds with any button press while the back light is on
Note: The back light is turned off by pressing the LIGHT button while the back light is on.
2.7 LOW VOLTAGE MESSAGE
When the LCD flashes “L»BAT", the batteries should be replaced
2.8 FACTORY RESET
Pressing the [POWER OFF] and [STOP] buttons for 10 seconds will erase all learned and pr-programrned
programs in the remote control and reset it to the factory default states The LCD will blink “ERASE” 9 times, clear
and then AUDIO.
No.
U'RC- l 00
Rev.
URC Proprietary n 1
Fufm E756 UnNewa Remote Control, Inc

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2003:07:08 14:37:36-03:00
Create Date                     : 2003:07:08 14:37:19-03:00
Creator                         : Acrobat 5.0 Scan Plug-in for Windows
Page Count                      : 7
Mod Date                        : 2003:07:08 14:37:36-03:00
Creation Date                   : 2003:07:08 14:37:19-03:00
Producer                        : Acrobat 5.0 Scan Plug-in for Windows
Metadata Date                   : 2003:07:08 14:37:36-03:00

EXIF Metadata provided by EXIF.tools