Ohsung Electronics URC9000LRF RF Remote Controller User Manual
Ohsung Electronics Co., Ltd. RF Remote Controller EMISSION TEST REPORT
a href="https://usermanual.wiki/Ohsung-Electronics" itemprop="url">
Ohsung Electronics >
Users Manual
![K. Programming Channel ControlYou can program the channel controls (ChannelUp, Channel Down, Last and Numbers) from one Deviceto operate in another Device mode. Default channel con-trol settings on the remote control are as follows:CBL : CBL T V :CBL AUD : AUD DVD :DVD AUX :AUXIf you wish to store the TV channel controls in TV mode,use the following steps.STEP1 Press the [OK/SEL] button and [TV] button simulta-neously for three seconds. The device LED will turnon for 30 seconds. The next step must be performedwhile the LED is on.STEP2 Press the [VOL] button. The device LED willblink.STEP3 Press [TV] button. The device LED will blink twice toconfirm the programming.*Note : To return TV device to CBL channel repeat stepsabove replacing [TV] with [CBL] in Step 3.L. Programming a ‘Macro’ button.If your remote model has custom-programmable Macro but-tons available(See Section 4), they can be programmed to actas a 'Macro' or Favorite Channel button in CABLE mode. Thisallows you to program up to five 2-digit channels, four 3-digitchannels or three 4-digit channels that can be accessed withone button press. STEP1 Press the [CBL] button to select the CBL mode.STEP2 Press the [MACRO] button and [OK/SEL] buttonsimultaneously for 3 seconds. The [CBL] buttonwill turn on for 30 seconds.STEP3 Enter the the 2, 3 or 4-digit code for the channel you want programmed first (for example,007) using the Number Pad, then press the[STOP] button. Then enter the code for the nextchannel (for example, 050), then press the [STOP]button. Repeat this process for the third channel.The [CBL] button will blink once for each channelentered.STEP4 Press the [CH] button to store the channelsthat were selected. The [CBL] button will blinktwice to confirm the storage of commands.To access the programmed channels, press the [MACRO]button once. This will bring up the first channel. Pressonce again and it will bring up the second channel. Pressagain and it will bring up the third channel.M. RF Setting Method.(RF Frequency: 418Mhz)STEP1 After installing the MRF-250C, press the [CBL]and [LIST] button simultaneously for 3 sec-onds. The [CBL] device LED will turn on indi-cating that it is ready to be programmed. TheLED will remain on for 30 seconds.STEP2 Enter the 2-digit ID number assigned to yourMRF-250C ID #. (00~09, A : 10, B : 11, C : 12, D : 13,E : 14, F : 15)STEP3 Once you have completed RF ID setting, Store the2-digit number by pressing the [CBL] button onceagain. The [CBL] device LED will blink twice toconfirm that the RF ID number has been stored.*Note : Install and select the ID # on the MRF-250C. (Forfurther details, refer to the MRF-250C manual.) Youcan operate up to 15 different equipment locations,each with an MRF-250C unique Receiver ID #. N. Low Battery WarningWhen the batteries are low and need to be replaced withfresh batteries, the Device LED lights will blink 2 times inH. Programming the AUX DeviceYou can take advantage of the AUX function to program adevices such as a media PC, gaming console or satelliteradio receiver. Follow the instruction in section B to pro-gram an AUX device. You can also program the AUX but-ton for a second TV, DVD or Audio Device. To do this fol-low the instructions below.STEP1 Turn on the 5th device you want to program (TV,AUD, DVD, etc.).STEP2 Press the [AUX] button and the [OK/SEL] buttonsimultaneously for 3 seconds. The [AUX] deviceLED will turn on for 30 seconds.STEP3 Press the [Device] button For the type of device youwant to setup. Point the remote control toward thedevice and enter the 3-digit code number assigned toyour brand.*Note : To program a second TV press TV, etc.STEP4 When the equipment turns off verify that youhave selected the correct code by pressing the[POWER] button. The equipment should turnback on. Then try all of the functions on theremote control (i.e. volume, mute, etc.) to ensureyou have the correct code. If any of the functionsdo not operate as they should, enter the next 3-digit code number from the brand list.STEP5 Once you have found the correct 3-digit code, save itby pressing the [AUX] button one more time. The[AUX] LED light will blink twice to confirm the codewas stored.I. Programming the System On/Off ButtonThis allows you to program the System On/Off button so itcan send up to five power On/Off commands with one but-ton press.STEP1 Press the [CBL] button.STEP2 Press the [SYSTEM ON/OFF] button and the[OK/SEL] button simultaneously for 3 seconds.The [CBL] button will turn on for 30 seconds.STEP3 Press the first [DEVICE] button you want to store inthe [SYSTEM ON/OFF] button and then the [POWER]button. Repeat this for other Components until youhave stored all the desired power commands into the[SYSTEM ON/OFF] button.STEP4 Press the [CH] button to save the power com-mands you stored. The [CBL] button will blinktwice to confirm the commands have beensaved.J. Programming Volume ControlVolume and Mute control are factory programmed to auto-matically transfer to the respective Device mode Youselect, as follows:CBL : CBL T V :TV AUD : AUDDVD :TV AUX : AUXIf you wish to store the TV volume control in CBL mode,use the following steps.STEP1 Press the [OK/SEL] button and [CBL] buttonsimultaneously for three seconds. The deviceLED will turn on for 30 seconds. The next stepmust be performed while the LED is on.STEP2 Press the [VOL] button. The device LED willblink.STEP3 Press [TV] button. The device LED will blink twiceto confirm the programming.*Note : To return CBL device to CBL volume repeat stepsabove replacing [TV] with [CBL] in Step 3 .Quick Set-up Code Tables6Set-up Code Tables70 SANYO1 SONY2 SAMSUNG3LG4 TOSHIBA5 PANASONIC6 PHILIPS7 HITACHI8 SHARP9 VIZIOCISCO/SA 001 003 041 042 045 046PIONEER 001 103 034 051 063 076 105PACE 001 005 002SAMSUNG 001 030MOTOROLA 002 111 148CE-LABS 164DIGEO 153EVOLUTION FTA 158GENERAL INSTRUMENT005 103 104HAMLIN 049 050 055HITACHI 103 055JERROLD 005 004 103 005 003 008 009 010 069MAGNAVOX 010 012MEMOREX 052MOXI 111 252 153NFUSION 192PANASONIC 044 047PHILIPS 006 012 013 020 085PULSAR 052RCA 047REGAL 049 050REGENCY 057SKY 230 204SONY 108SPRUCER 047TELNET 354TOCOM 039 040 056TOSHIBA 052VIEWSTAR 012 015ZENITH 052 060 093 100A MARK 112 143ABEX 025ACCURIAN 036ADMIRAL 072 251 333 ADVENT 247 388ADVENTURA 002AIKO 103AKAI 116 146 248 404 405 473 475 323 387 391 615ALBATRON 017ALERON 028AMERICA ACTION 043AMPRO 073AMSTRAD 052ANAM 043 054 056 080 112 AOC 116 363 112 058 616APEX 572APEX DIGITAL 006AQUAVISION 573 574ASTAR 477AUDIOVOX 076 454 388AVENTURA 052AVION 441AXION 039BELCOR 116BELL&HOWELL 333 072BENQ 423 600BOXLIGHT 266BRADFORD 043BROCKWOOD 116BROKSONIC 238BYDESIGN 031 032CANDLE 116 002 003 363CAPEHART 058CARY AUDIO DESIGN266CELEBRITY 001CENTURION 116CETRONIC 043CHANGHONG 247CITIZEN 116 002 003 363 043 258 103 143CLARION 043CLASSIC 043CLP CLASSIC 333COLORTYME 116CONCERTO 363CONCIERGE 073CONTEC 043 050 051CORNEA 116CORONADO 143CRAIG 043 054CROSLEY 164CROWN 043 143CURTIS MATHES 116 258 363 143CXC 043CYBERHOME 015DAEWOO 363 016 043 044 076 103 114 125 127 143DAYTRON 363 143DELL 320 164 363 618DIGITAL PROJECTION570DIMENSIA 333DREAMVISION 235DUKANE 011 025DUMONT 116 073DURABRAND 096 052DWIN 257DYNASTY 043DYNEX 400EIKI 187ELECTROBAND 001ELECTROGRAPH 466ELECTROHOME 143 024 076 196ELEKTRA 072ELEMENT 363 494 526 622EMERSON 028 048 043 155 005 116 363 047 050 051 076 096 143 153 154 052 514 ENVISION 116EPSON 324 590ESA 323FISHER 007 057FUJITSU 246 198 410FUNAI 028 043 052FUTURETECH 043GATEWAY 242 268GE 073 116 008 009 034 056 074 155 333 363GEM 391GIBRALTER 116 073GO VIDEO 026GOLDSTAR 113 116 102 363 106 112 127 143GRUNPY 028 043HAIER 363 501 623HALL MARK 363HANNSPREE 349 381Manufacturer/BrandSet-Up Code NumberCBL-CABLE ConvertersManufacturer/BrandSet-Up Code NumberTVQuick NumberManufacturer/BrandTV0 ROTEL1 DENON2 YAMAHA3 MARANTZ4 SONY5 INTEGRA6 HARMAN KARDON7 PIONEER8 ONKYO9 LEXICONQuick NumberManufacturer/BrandAUDIO0 HITACHI1 SONY2 PHILIPS3 SAMSUNG4 PHILIPS MAGNAVOX5 PANASONIC6LG7 JVC8 DENON9 PIONEERQuick NumberManufacturer/BrandDVD0 BOSE1HP2 APPLE / iPod3 APPLE / iPod4 MICROSOFT / XBOX5 SONY / PS26 LUTRON7X-108X-109 MICROSOFT / XBOXQuick NumberManufacturer/BrandAUXManufacturer/BrandSet-Up Code NumberTVA. Quick Set-Up MethodSTEP1 Turn on the equipment you want to program. To pro-gram your TV, turn on the TV.STEP2 Point the remote at the component and pressand hold the [DEVICE] key for 3 seconds until theDevice LED blinks off and turns back on.Continue holding the [DEVICE] key and press thenumber keys, one at a time, starting with 1, then2, 3...0. Stop pressing the number keys when thedevice turns off.STEP3 Release the [DEVICE] key to save the code. TheDevice LED will blink twice to confirm the code isstored.Repeat the steps above for all components (TV, AUD,DVD, AUX).B. Pre-Programmed 3-Dight Code MethodSTEP1 Turn on the equipment that you want the remotecontrol to operate (Cable Box, TV, DVD, etc.).STEP2 Press the [DEVICE] button and the [OK/SEL] buttonsimultaneously for three seconds. The corre-sponding device LED will turn on indicating that itis ready to be programmed. The LED will remainon for 30 seconds. The next step must be enteredwhile the LED is on.STEP3 Point the remote control toward the equipmentand enter the three-digit code number assignedto your brand from the code tables. If there aremore than one three-digit number listed for yourbrand, try one code number at a time until yourequipment turns off.*Note : You can verify that you have selected the correctcode by pressing the [POWER] button. The equip-ment should turn back on. Then try all of the func-tions on the remote control (i.e. volume, mute, etc.)to ensure you have the correct code. If any of thefunctions do not operate as they should, repeat theinstructions from STEP 3 above using the nextthree digit code number from the brand list.STEP4 Store the three-digit code by pressing the same[DEVICE] button once again. The device LED willblink twice to confirm that the code has beenstored.C. Auto-Search MethodIf none of the three digit code numbers assigned to yourbrand of equipment works, or the code table does not listyour brand, you can use the Auto Search Method to find thecorrect three-digit code number for your equipment by fol-lowing steps:STEP1 Turn on the equipment that you want the remotecontrol to operate (Cable Box, TV, DVD, etc.).STEP2 Press the [DEVICE] button and the[OK/SEL] button simultaneously for threeseconds. The device LED will turn on indi-cating that it is ready to be programmed. The LED will remain on for30 seconds. The next step must be enteredwhile the LED is on.STEP3 Press the [CH] or [CH] button one at a time orkeep it pressed. The remote will emit a series ofPower ON/OFF code signals. Release the [CH] or[CH] button as soon as the equipment turns off.*Note : You can verify that you have selected the correctcode by pressing the [POWER] button. The equip-ment should turn back on. Then try all of the func-tions on the remote control (i.e. volume, mute, etc.) toensure you have the correct code. If any of the func-tions do not operate as they should, repeat theinstructions from STEP 3 above to continue the AutoSearch Method.STEP4 Press the same [DEVICE] button to store the code.The Device LED will blink twice to confirm that thecode has been stored.D. The Learning MethodSTEP1 Press the [DEVICE] button (TV,AUD, DVD, or AUX) tobe programmed and the [ASPECT] buttons simulta-neously for 3 seconds until the Device LED light turnson.STEP2 Line up the PHAZR-5 to the remote control youwant to "learn" from, head-to-head, 1 or 2 inchesapart.STEP3 Press the button on the PHAZR-5 that you wantto teach a command to. For example, press the[MUTE] button to learn a command to the[MUTE] button.STEP4 Press and hold the button on the other remote thatcorresponds to the command you want to teachuntil the PHAZR-5 Device LED light blinks twice.*Note : The LED will blink 5 times if there was an errorin the learning process. Repeat STEPS 3 and 4if this occurs. Continue learning other buttonsby repeating STEPS 3 and 4.STEP5 Once you have completed teaching the PHAZR-5all desired commands for the component, savethe learned commands by pressing the [DEVICE]and [ASPECT] buttons simultaneously until theDevice LED blinks 3 times. Now test all of thebuttons to make sure they operate correctly.E. Erasing a Single Learned CommandSTEP1 Press the [DEVICE] and [ASPECT] buttons simulta-neously for 3 seconds until the Device LED lightturns on.STEP2 Press and hold the button you want to erase for3 seconds. The Device LED will blink twice toconfirm the erasure.STEP3 To exit, press and hold both the [DEVICE] and[ASPECT] buttons simultaneously until theDevice LED blinks 3 times.F. Erasing All Learned Commands from One DeviceSTEP1 Press the [DEVICE] and [ASPECT] buttons simulta-neously for 3 seconds until the Device LED lightturns on.STEP2 Press and hold both the [DEVICE] button you wantto erase and the [PAUSE] button for 5 seconds.The Device LED will blink twice to confirm the era-sure.STEP3 To exit, press and hold both the [DEVICE] and[ASPECT] buttons simultaneouslyG.To Identify the 3-Digit Code Programmed for aDeviceSTEP1 Press the appropriate [DEVICE] button and the[OK/SEL] button simultaneously for three sec-onds. The device LED will turn on for 30 seconds.The next step must be performed while the LEDis on.STEP2 Press the [INFO] button. The device LED will blinka number of times indicating the number of eachdigit for the code. Each digit is separated by a onesecond interval of the LED being off.Example :One blink, (pause) three blinks, (pause) eightblinks indicates the code number 138.*Note : Ten blinks indicates the number 0.sequence whenever a [POWER] button is pressed to turnon equipment.O. Memory Lock SystemThis remote control is designed to retain programmedmemory for 10 years even after batteries are removedfrom the remote control.P. Record Your Component Set-up CodesTV Set-up Code Number: AUD Set-up Code Number:DVD Set-up Code Number:AUX Set-up Code Number:For additional information about your remote control, go towww.universalremote.comQ. Federal Communication Commission InterferenceStatementThis equipment has been tested and found to complywith the limits for aClass B digital device, pursuant topart 15 of the FCC Rules. These limits aredesigned to pro-vide reasonable protection against harmful interferencein aresidential installation. This equipment generates,uses and can radiate radiofrequency energy and, if notinstalled and used in accordance with the instruc-tions,may cause harmful interference to radio communica-tions. However, there is no guarantee that interference will notoccur in a particularinstallation. If this equipment doescause harmful interference to radio or tele-vision recep-tion, which can be determined by turning the equipmentoff andon, the user is encouraged to try to correct theinterference by one more of thefollowing measures:Reorient or relocate the receiving antenna.Increase the separation between the equipmentand receiver.Connect the equipment into an outlet on a circuitdifferent fromthat to which the receiver is con-nected.Consult the dealer or an experienced radio/TVtechnician for help.Warning!Changes or modifications not expressly approved by themanufacturer couldvoid the user's authority to operatethe equipment.*Note : The manufacturer is not responsible for anyRadio or TV interferencecaused by unautho-rized modifications to this equipment. Suchmodificationscould void the user's authority tooperate the equipment.FCC CautionThis device complies with Part 15 of the FCC Rules.Operation is subject to thefollowing two conditions: (1)this device may not cause harmful interference,and (2)this device must accept any interference received,including interferencethat may cause undesired opera-tion.Any changes or modifications not expressly approved bythe party responsiblefor compliance could void theauthority to operate equipment.The antenna(s) used for this transmitter must not be co-located or operating inconjunction with any other anten-na or transmitter.Button Functions4Programming the Remote Control5IMPORTANT SETUP NOTE! In this section when you are instructed to press a [DEVICE] button, that means to press either the CBL, TV, AUD,DVD or AUX button, depending on what device you are programming the remote to operate.There are five ways you can program your remote:* Quick Set-Up Method * The Pre-Programmed 3-Digit Code Method* The Auto-Search Method * The Learning Method * RF Setting MethodThe Quick Set-Up Method is a unique feature that enables the fastest and easiest setup by using a 1 digitcode. This is the quickest way to set up devices made by popular manufacturers.The Pre-Programmed Code Method allows you to setup all of the buttons at once by entering 3-digitcode numbers that correspond with the components manufacture/brand. Code tables for this methodare on the backside of the operating instructions.The Auto-Search Method scans through all of the codes in the remote control, one at a time allowing youto identify the correct code.The Learning Method allows you to transfer functions from other remotes to the PHAZR-5 one button at a time.IMPORTANT SETUP NOTE! This pertains to all programming steps. When you are in setup mode the device LED will light for 30 seconds. If you donot press a button within 30 seconds, the LED light will turn off and exit setup mode, and you will need to start over.Universal Remote Control, Inc.www.universalremote.comOCE-0087C Rev 01 (04/01/11)Operating Instructions ForPHAZR-5Cable Remote ControlThe PHAZR-5 UR5L-9000LRF & UR5L-9020LRF is designed to operate the CISCO/ SA, Pioneer, Pace Micro, Samsung andMotorola digital set tops, Plus the majorityof TV, AUD, DVD and AUX equipment onthe market as shown below.CBL : Cable Set-top Box TV : Televisions AUD : Audio Receivers DVD : DVD PlayersAUX : Media PC, Gaming System, etc.Introduction1DEFAULT STATE: Device Default: Cable Set-Top Box (STB)Channel Default: CABLE channel and numbersthrough the CABLE STB. You have the option ofcontrolling your CABLE channel and numbersthrough the TV or AUD. Refer to section Kforprogramming steps.Volume Default: Volume and Mute control areautomatically transferred to the respectiveComponent based on the Device selected: CBL:Cable Set-Top Box ; TV:TV ; AUD:AUD.DVD:TV ; AUX:AUX. You have the option ofcontrolling CABLE Volume and Mute throughthe TV, DVD or AUD. Refer to section Jforprogramming steps.Operations3Replacing Batteries2Before you program or operate the remote control,you must install two new AA alkaline batteries.STEP1 Remove the battery compartment coveron the back of your remote control.STEP2 Check battery polarity carefully, andinstall the batteries as shown in theillustration below.STEP3 Replace the battery compartment cover.UR5L-9000LRF & UR5L-9020LRF](https://usermanual.wiki/Ohsung-Electronics/URC9000LRF/User-Guide-1447192-Page-2.png)