Ohsung Electronics URCDMSIN Stream Injector Input Device User Manual EMISSION TEST REPORT

Download:
Mirror Download [FCC.gov]
Document ID	3234067
Application ID	eMBjQHdtfL2k7/yD7fmOXg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	49.82kB (622774 bits)
Date Submitted	2016-12-20 00:00:00
Date Available	2017-02-03 00:00:00
Creation Date	2016-12-14 16:51:26
Producing Software	Adobe PDF Library 11.0
Document Lastmod	2016-12-14 16:51:42
Document Title	EMISSION TEST REPORT
Document Creator	Wordìš© Acrobat PDFMaker 11
Document Author:	최선미

Order Number
: GETEC-C1-16-415
FCC Part 15 Certification
Test Report Number
: GETEC-E3-16-053
Page 1 / 1
APPENDIX G
: USER’S MANUAL
EUT Type: Stream Injector Output Device
FCC ID.: OZ5URCDMSIN
DMS-IN
Owner’s Manual
Universal Remote Control
www.UniversalRemote.com
DMS-IN Owner’s Manual
Overview
The DMS-IN allows an additional audio source to be added to the DMS
“family” of streaming sources. Whether it is simply adding an additional
audio input to the system or adding a device from a different room, the
DMS-IN makes this possible. This is a perfect solution device to help
overcome the native input capacity created by the DMS-1200 and the
DMS-100.
Table of Contents
Features and Benefits.........................................1
Parts & Pieces......................................................1
Online Help:
Requirements......................................................1
Visit the URC Control Room for software downloads, training materials, and
frequently asked questions.
Rear Panel............................................................2
Contact Support:
Total Control is a URC product sold direct or through distribution. For
questions or assistance contact your Custom Installer/Programmer.
Top Panel & LED States......................................4
Bottom Panel.......................................................5
My Installer/Programmer:
Wiring the DMS-IN.............................................6
or URC Technical Support at: techsupport@universalremote.com
(914) 835-4484
Universal Remote Control, Inc.
500 Mamaroneck Ave
Harrison, New York 10528
Toll Free: (800) 901-0800
DMS-IN Owner’s Manual
Features and Benefits
The DMS-IN is loaded with features to provide the perfect audio experience. Enjoy features such as:
● Additional Source
DMS-IN adds an additional streaming source to any existing DMS Multi-zone audio system.
● Audio Sensing Capability
The DMS-IN, similar to the URC Audio Sensor (SEN-AUD), can detect an audio signal which can then trigger n activity (macro).
● Flexible Power Source
Use the supplied 5V DC power adapter or take advantage of the DMS-IN’s PoE (Power Over Ethernet) capability using a CAT 5/6 wiring.
Parts & Pieces
Requirements
Contained within the DMS-IN box:
1. DMS-IN Stream Injector Input Device
As with all Total Control products, the DMS-IN is not a
plug-and-play device. It requires programming by a
certified Total Control installer in order to work properly.
2. 5v DC Power Adapter
Be sure the system contains the following:
3. Wall Mount and 4x Screws
● MFS-8 or MFSPOE-8
● MRX-10 or MRX-8 Master System Controller
● URC User Interface (TRC-1080, TKP-7000, etc.)
Page 1
DMS-IN Owner’s Manual
Rear Panel:
5V DC Input:
Provides power to the DMS-IN. PoE may be used
as a substitute.
Analog Input:
Standard RCA (analog) connector.
Note: Does not natively support phono audio. If phono
is desired a line level converter is required.
Digital Input - Optical:
This input uses standard S/PDIF OPTICAL TOSLINK
connector.
Note: The DMS-IN converts Dolby Digital 5.1/DTS 5.1
to a DMS Stream.
Page 2
DMS-IN Owner’s Manual
Digital Input - Coax:
Standard RCA (analog) connector, this receives
bitstreams of audio data.
Note: The DMS-IN converts Dolby Digital 5.1/DTS 5.1
to a DMS Stream.
LAN Port:
This 10/100 Ethernet port supports PoE and sends
the URC Audio stream through the local network,
this is also how the DMS-IN receives commands
and sends audio.
Note: The DMS-IN does not support Wi-Fi
Page 3
DMS-IN Owner’s Manual
Top Panel & LED States:
There are three (3) LED lights at the top of the DMS-IN which can provide users with basic troubleshooting information.
Status LED
● Off
Unit has not been programmed with a Total Control file.
● Yellow
Unit has been programmed with a Total Control file; however, is not creating
a DMS Audio Stream.
● Blue
Unit has been programmed with a Total Control file and is creating a DMS
Audio Stream through the network.
Power LED
● Off
Unit is not receiving power.
● Blue
Unit is receiving power via 5V DC adapter or PoE.
Page 4
DMS-IN Owner’s Manual
Network LED
● Off
Unit is not connected to the local area network and cannot send/receive data.
● Blinking Green
Unit is connected to the local network, but has not received an IP address.
● Green
Unit is connected to the local network and has an IP address.
Bottom Panel
Located beneath the DMS-IN is a Reset button. The Reset button is recessed so a
paperclip or something similar is required to press. This button allows for:
● Rebooting the DMS-IN
A momentary press of the Reset button reboots the DMS-IN, similar to
unplugging it from the power supply.
● Factory Default
Pressing and holding the Reset button for ten (10) seconds or longer, factory
resets the DMS-IN to its factory state. The DMS-IN requires re-programming
after this has been performed.
Page 5
DMS-IN Owner’s Manual
Wiring the DMS-IN
In order for the DMS-IN to provide the best possible experience, it must be first wired correctly then programmed by a Total Control Certified
Installer. Follow these steps to prepare the DMS–IN for programming:
1. Power the DMS-IN with the supplied 5V DC adapter OR PoE using the LAN port (see below)
OR
2. Connect and Ethernet cable from the LAN 10/100 port to an MFS-8/MFSPOE-8
● The 5V DC adapter is not required when using PoE
3. Connect a source via Analog or Digital that is to be a part of the DMS Audio Stream
Only one source can be used at a time, further audio
adjustments can be made from within Accelerator.
Additional set up is required via the URC Accelerator software. Contact a Certified Total Control Installer to properly configure the DMS-IN to a
new or existing system.
Page 6
DMS-IN Owner’s Manual
Specifications
Microprocessor: Cortex-A5 600MHz
Memory: 128MB NAND, 128MB RAM
Network: One 10/100 Ethernet port (PoE)
Weight: 5.8oz
Size: 4.6” x 4.6” x 1.2”
Power: Standard PoE Injector or PoE Switch (purchased separately), DC 5V/1A
Page 7
DMS-IN Owner’s Manual
Limited Warranty Statement
1. Limited Warranty and Disclaimers
Universal Remote Control, Inc. (“URC”) warrants that the URC equipment shall be
free from defects in material and workmanship under normal usage for one (1)
year from purchase when such is purchased from URC. This limited warranty is
valid only in the United States of America. URC warrants that the software will
substantially conform in any material respect to its functional specifications at the
time of delivery. URC SHALL NOT BE LIABLE FOR OPERATIONAL, TECHNICAL OR
EDITORIAL ERRORS AND/OR OMISSIONS MADE IN THE URC DOCUMENTATION.
URC DOES NOT WARRANT THAT THE URC SOFTWARE IS BUG-FREE OR ERROR
FREE OR THAT THERE ARE NO ERRORS/BUGS IN THE URC SOFTWARE.
URC warrants that at the time of purchase the URC equipment and the URC
software complied with all applicable regulations and policies of the Federal
Communications Commissions (“FCC”) regarding electromagnetic interference
caused by electronic/computing devices and to the extent that the URC
equipment and/or the URC software fails to so comply, URC shall, at its own
expense, take all reasonable measures to promptly cause such to comply.
URC equipment purchases from other than an authorized URC dealer or
distributor are without warranty.
THIS LIMITED WARRANTY DOES NOT COVER TECHNICAL ASSISTANCE FOR
HARDWARE OR SOFTWARE USAGE EXCEPT AS EXPRESSLY PROVIDED FOR
HEREIN, THE EQUIPMENT, SOFTWARE AND DOCUMENTATION OF URC ARE
SUPPLIED “AS IS” WITHOUT ANY WARRANTY, EXPRESS, STATUTORY OR IMPLIED,
OF ANY KIND. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, URC
EXPRESSLY DISCLAIMS ALL WARRANTIES, EXPRESS, STATUTORY OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY AND
Page 8
DMS-IN Owner’s Manual
FITNESS FOR A PARTICULAR PURPOSE. URC DOES NOT WARRANT, GUARANTEE,
OR MAKE ANY REPRESENTATIONS REGARDING THE USE OF, OR THE RESULTS OF
THE USE OF, THE EQUIPMENT, SOFTWARE OR DOCUMENTATION IN TERMS OF
CORRECTNESS, ACCURACY, RELIABILITY OR OTHERWISE. EXCEPT AS EXPRESSLY
PROVIDED FOR HEREIN, TECHNICAL SERVICES ARE SUPPLIED “AS IS”, WITHOUT
ANY WARRANTY, EXPRESS, STATUTORY OR IMPLIED, OF ANY KIND. TO THE
MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, URC EXPRESSLY DISCLAIMS
ALL WARRANTIES, EXPRESS, STATUTORY OR IMPLIED, INCLUDING BUT NOT
LIMITED TO THE WARRANTIES OF QUALITY OR REASONABLE SKILL AND CARE,
OR OUTCOME OR RESULTS.
WITHOUT IN ANY WAY LIMITING THE GENERALITY OF THE OTHER PROVISIONS
HEREIN, WARRANTY DOES NOT COVER: (I) DAMAGE FROM MISUSE, NEGLECT
OR ACTS OR NATURE, (II) MODIFICATIONS, (III) INTEGRATION WITH THIRD
PARTY CONTENT (IV) BEYOND THE WARRANTY PERIOD AND/ OR FAILURE TO
FOLLOW URC WARRANTY CLAIM PROCEDURE.
The warranty limitations and warranty disclaimers may not apply to end user in
whole or in part, where such are restricted or excluded by applicable law and such
shall apply to the maximum extent permitted by applicable law.
In the event of any warranty claim, URC will, at its sole option, repair the URC
equipment using new or comparable rebuilt parts, or exchange the URC
equipment for new or rebuilt equipment. In the event of a defect, these are the
end user’s exclusive remedies.
All the URC equipment returned for service, exchange or repair require an RGA
number. To obtain an RGA number, you must complete a Return Request Form
which you may obtain by calling (914) 835-4484 or contacting URC at
returnrequest@universalremote.com. To obtain warranty service, end user must
deliver the URC equipment, freight prepaid, in its original packaging or packaging
Page 9
DMS-IN Owner’s Manual
affording adequate protection to URC at 420 Columbus Avenue, Valhalla, NY
10595. It is end user’s responsibility to backup any macro programming, artwork,
software or other materials that may have been programmed into the unit. It is
likely that such data, software, or other materials will be lost during service and
URC will not be responsible for any such damage or loss. A dated purchase
receipt, bill of sale, installation contract or other verifiable proof of purchase is
required. For the URC equipment support and other important information,
please visit URC's website available at www.universalremote.com or call the
Customer Service Center at (914) 835-4484.
This limited warranty only covers the URC equipment issues caused by defects in
material or workmanship during ordinary consumer use. It does not cover
product issues caused by any other reason, including but not limited to product
issues due to commercial use, acts of God, third-party installation, misuse,
limitations of technology, or modification of or to any part of the URC equipment.
This limited warranty does not cover the URC equipment sold as used, as is,
refurbished, so called "B stock" or consumables (such as batteries). This limited
warranty is invalid if the factory applied serial number has been altered or
removed from the URC equipment. This limited warranty specifically excludes the
URC equipment sold by unauthorized resellers.
With the exception of URC’s IR-only, broad-based consumer remotes, none of
Page 36 URC’s PC programmable remotes or any of our Total Control® wholehouse equipment are authorized for online internet sales. Buying URC’s PC
programmable remotes or any of our Total Control® wholehouse equipment
online means buying equipment that does not have a URC’s limited warranty.
Such equipment is not eligible for URC tech support or software support, either.
Page 10
DMS-IN Owner’s Manual
2. URC’s Limitations of Liability
IN NO EVENT SHALL URC BE LIABLE FOR INDIRECT, SPECIAL, INCIDENTAL,
EXEMPLARY, PUNITIVE OR CONSEQUENTIAL DAMAGES OF ANY KIND OR LOSS
OF PROFITS OR BUSINESS OPPORTUNITY, EVEN IF URC IS ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
IN NO EVENT SHALL URC BE LIABLE FOR LOSS OF OR DAMAGE TO DATA,
COMPUTER SYSTEMS OR COMPUTER PROGRAMS. URC’S LIABILITY, IF ANY, FOR
DIRECT DAMAGES OF ANY FORM SHALL BE LIMITED TO ACTUAL DAMAGES, NOT
IN EXCESS OF AMOUNTS PAID BY END USER FOR THE URC EQUIPMENT.
IN NO EVENT SHALL URC BE LIABLE FOR ANY EVENTS BEYOND ITS CONTROL,
INCLUDING ANY INSTANCE OF FORCE MAJEURE. IN NO EVENT SHALL URC BE
LIABLE FOR THE ACTS OR OMISSIONS OF END USER OR ANY THIRD PARTY.
THE LIMITATIONS OF LIABILITY MAY NOT APPLY TO END USER IN WHOLE OR IN
PART, WHERE SUCH ARE RESTRICTED LIMITED OR EXCLUDED BY APPLICABLE
LAW AND SUCH SHALL APPLY TO THE MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW.
URC SHALL NOT BE HELD RESPONSIBLE FOR THE STATEMENTS MADE BY
OTHERS.
SOME STATES OR JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO END USER. THIS LIMITED
WARRANTY GIVES END USER SPECIFIC LEGAL RIGHTS AND END USER MAY
HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR JURISDICTION TO
JURISDICTION.
Page 11
DMS-IN Owner’s Manual
End User Agreement
The terms and conditions of the End User Agreement available at
www.universalremote.com/eua.php shall apply.
Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one more of the following
measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
Page 12
DMS-IN Owner’s Manual
Warning!
Changes or modifications not expressly approved by the manufacturer could void the
user's authority to operate the equipment.
Note: The manufacturer is not responsible for any Radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the authority to operate equipment.
Page 13
DMS-IN Owner’s Manual
Regulatory Information to the user
● CE conformity Notice
Products with “CE” marking comply EMC Directive 2014/30/EU issued by the
commission of the European Community.
1. EMC Directive
● Emission :EN 55032
● Immunity :EN 55024, EN55020
● Power
:EN-61000-3-2, 3
● Declaration of Conformity
“Hereby, Universal Remote Control Inc. declares that this DMS-IN is in compliance
with the Essential requirements:
Certification
Type No.(Model No.)
Batch/Serial No.
Power Rating
DMS-IN
48.0V
, 0.32A, DC 5V 1A
Page 14
DMS-IN Owner’s Manual
Declaration of Conformity
Company Name
Universal Remote Control Inc.
Company Address
Contact Information
Brand Name
500 Mamaroneck Avenue, Harrison, NY 10528, U.S.A
www.universalremote.com
Phone: (914)835-4484 Fax: (914)835-4532
UNIVERSAL remote control
Product Name
Stream Injector Input Device
Model Name
DMS-IN
This product herewith complies with the requirements of EMC Directive (2014/30/EU)
issued by the Commission of the European Community
Compliance with these directives implies conformity to the following European Community
EMC Directive
EN 55032
EN 55020
EN 55024
EN 61000-3-2
EN 61000-3-3
List of test reports and/or certificate verified compliance with the standards above
Date of issue
EMC Directive
Report No.
December 01, 2016
GETEC-E2-16-110
Testi ng Labora tory
: Gumi University EMC Center
Name and signature of authorized person :
James Novak
Director of Product
Universal Remote Control Inc.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : 최선미
Create Date                     : 2016:12:14 16:51:26+09:00
Modify Date                     : 2016:12:14 16:51:42+09:00
Subject                         : 
Language                        : EN-US
Tagged PDF                      : No
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2016:12:14 16:51:42+09:00
Creator Tool                    :  Word용 Acrobat PDFMaker 11
Document ID                     : uuid:86f92e48-5a2e-42c1-aec3-e827b552864b
Instance ID                     : uuid:9095bbf4-5f2c-4fc5-b4de-d7a7781ed219
Format                          : application/pdf
Title                           : EMISSION TEST REPORT
Description                     : 
Creator                         : 최선미
Producer                        : Adobe PDF Library 11.0
Keywords                        : 
Source Modified                 : D:20161214065128
Company                         : emc센터
Comments                        : 
Page Layout                     : OneColumn
Page Count                      : 18

EXIF Metadata provided by EXIF.tools