Oki Microline 8480Fb Users Manual ML8480FB UG AE 59380401 Rev 1_1

2014-12-11

• Copyright Information
  • Document Information
  • Disclaimer
  • Trademark Information
  • Regulatory Information
• Contents
• Introduction
  • Features
  • Front View, Outside
  • Front View, Inside (1)
  • Front View, Inside (2)
  • Rear View
• Control Panel
  • Quick Reference: Control Panel Functions
    • Enter the Menu
    • Print the Menu
    • Change Print Modes
    • Change the Printhead Gap
    • Change Paper Paths
    • Move Continuous Forms to the Print Position
    • Park Continuous Forms
    • Move Continuous Forms to the Tear Off Position
    • Change Align x Setting
• Print Modes
  • Normal Print Mode
  • High Speed Print Mode
  • High Impact Print Mode
  • Change Print Mode
    • Change to Normal
    • Change to High Speed
    • Change to High Impact
• Loading Print Media
  • Individual Sheets/Forms (“MANUAL”)
    • Specifications
      • Individual Sheets/Forms, for Use with Auto Align Mode
      • Minimum Print Margins
      • Individual Sheets
      • Individual Multipart Forms
    • Load Individual Sheets/Forms
  • Continuous Forms (“FRONT”)
    • Specifications
      • Width
      • Single Thickness Forms
      • Multi-part Forms
    • Load Continuous Forms
  • Switching Between Normal and High Impact Mode
    • Normal to High Impact Print Mode
    • High Impact to Normal Print Mode
  • Switch between Single Sheets and Continuous Forms
    • Single Sheets to Continuous Forms
    • Manual Feed to Front Feed
    • Continuous Forms to Single Sheets
    • Front Feed to Manual Feed
• Function Setting Menu
  • Print the Menu
  • Navigating the Menu
    • Groups, Items, and Settings
    • Access the Menu
    • Scrolling Through Groups, Items and Settings
      • Groups
      • Items
      • Settings
    • Exit the Menu
    • Example: Turn on Proportional Spacing and Form Tear-Off
  • Reset to Factory Defaults
  • Print the Menu
    • Single Sheet (Manual Feed)
      • Before Starting
      • Print the Menu on Single Sheets
    • Continuous Forms (Front Feed)
      • Before Starting
      • Print the Menu on Continupus Forms
  • Menu Summary
  • Explanation of Menu Items
    • 1stDotAdjAlign
    • 1stDotAdjCut
    • 1stDotAdjFront
    • Align1 Pos. Adj.
    • Align2 Pos. Adj.
    • Align3 Pos. Adj
    • Align4 Pos. Adj.
    • Auto Align
    • Auto Align Detect
    • Auto Align (POW)
    • Auto CR
    • Auto Eject Pos.
    • Auto Feed XT
    • Auto LF
    • Buzzer
    • Buzzer Volume
    • Character Set
    • Check Print Area
    • Code Page
    • CutSheet Smooth
    • Eject Dir.
    • Emulation Mode
    • Form Tear-Off
    • Front Load Adj.
    • Gap Control
      • Manual Gap Settings
    • Gap Pos.
    • Graphics
    • High Skip
    • Hi-Impact Copy
    • Host Interface
    • I-Prime
    • I/F Time Out
    • Initial Pos.
    • Language Set
    • Line Spacing
    • LF Revise (Cut)
    • Load LF Speed
    • Memory Auto Align
    • Multi Pass
    • Page Length
    • Page Width
    • Paper End
    • Parallel I/F
    • Path Change
    • PE Adj. (Cut) [Paper End Adjust (Manual Feed)]
    • PE Adj. (Front) [Paper End Adjust (Front Feed)]
    • PE Pos. [Paper End Position]
    • Pitch
    • Power Save Time
    • Power Saving
    • Print Dir. Cmd.
    • Print Mode
    • Print Suppress
    • Prop. Spacing
    • Quiet
    • Rcv. Buffer
    • Regist. Low
    • Regist. Normal
    • Regist. High 1
    • Regist. High 2
    • Reset Inhibit
    • Set Alarm
    • SI Pitch (10)
    • SI Pitch (12)
    • Size
    • Skew Detect
    • Skp Ovr Binding
    • Skip Over Perf.
    • Style
    • TOF
    • TOF Adj. (Cut)
    • Wait Time
    • Zero Character
• Auto Align
  • Disabling Auto Align
• Set Top of Form (TOF)
  • General Information
  • Use the Printer Menu
  • Use 1Chr Set Pos
    • Front Feed (Continuous Forms)
    • Manual Feed (Single Sheets/Forms)
  • Temporary TOF
    • Use the Control Panel
• Form Tear Off
  • Turn On Forms Tear Off
  • Move Continuous Forms Up for Tear Off
• Tests
  • Rolling ASCII Test
  • Font Sample Test
  • Hex Dump Mode
    • Engaging the Hex Dump Mode
    • Running a Hex Dump Test
    • Exiting Hex Dump Mode
• Setting the Printhead Gap
  • General Information
  • Printhead Gap Settings
  • Change to a Manual Printhead Gap Setting
    • “On-the-Fly”
    • In the Menu
• Troubleshooting
  • Paper Jams: Single Sheet
  • Paper Jams: Continuous Forms
  • Paper Jams: Correcting Repetitive Jams
  • Error Messages
• Maintenance
  • Replace the Ribbon
  • Clean the Housing
• Control Codes
  • In Sequence by ASCII Code
  • In Sequence by Function
• Specifications
  • Print Method
  • Printhead
  • Emulations
  • Interfaces (Standard)
  • Receive Buffer Size
  • Throughput
  • Print Speed
  • Characters per Line (CPL)
  • Graphics Resolution
  • Resident Fonts
  • Reliability
  • Print Media Specifications
    • Single Sheets
    • Individual Multi-Part Forms
    • Continuous Single-Part Forms
    • Continuous Multi-Part Forms
    • Envelopes
  • Printer Dimensions
  • Printer Weight
  • Environmental Requirements
  • Electrical Requirements