Omega Engineering Ppp3P Users Manual Pressure Pump

PPP3P to the manual 33c7d520-b189-6e64-419a-3e2dd5b84c44

2015-02-02

: Omega-Engineering Omega-Engineering-Ppp3P-Users-Manual-439910 omega-engineering-ppp3p-users-manual-439910 omega-engineering pdf

Open the PDF directly: View PDF .
Page Count: 4

OMEGA

Operator´s Manual

PPP–3P

Precision Pressure Pump

GENERAL OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

IMPORTANT: Read all operating instructions and general operating information

before

beginning any test procedures.

PRODUCING NEGATIVE PRESSURE

1) Perform Step 1 as described above.

2) Turn the brass fine pressure adjustment fully

clockwise until resistance is felt. Do not over-

tighten.

3) Turn the discharge knob fully clockwise. Do

not overtighten.

4) Turn the fine pressure adjustment counter-

clockwise to generate the desired negative

pressure (to -2 psig).

WARNING

Even nominal pressure values can generate

extreme force if fitting or tubing failure occurs due

to improper installation or usage. Since the Model

PPP-3P is capable of generating pressures over

100 psig, it is imperative that all pressure

connections and test procedures be done by

qualified service personnel, according to standard

engineering practices, to prevent possible

personal injury or equipment damage.

PRODUCING POSITIVE PRESSURE

1) Connect one of the Model PPP-3P’s ports to the

instrument to be calibrated or checked. Use

small-diameter tubing as short in length as

possible (this will maximize the pressure adjust-

ment range). An auxiliary port is provided for

simultaneous output to a second device, e.g.,

application of pressure to an instrument or

system under test and to a pressure standard to

measure the actual pressure output. If the

auxiliary port is not used, it should be securely

plugged.

2) Set the brass fine pressure adjustment knob on

the top of the pump to the mid-travel position as

indicated by the line cast into the pump body.

3) Turn the black discharge knob on the side of the

pump fully clockwise. Do not overtighten.

4) Squeeze the actuating levers to generate

pressure. At pressures above 150 psig the le-

vers should be squeezed harder and more quickly

at the end of the stroke. Additional force is

required to open the discharge valve due to

higher line pressure.

5) Use the discharge and fine pressure knobs to

adjust pressure to the desired level.

LEAK PREVENTION AND DETECTION

In order to obtain maximum pressure indication

stability, leaks must be avoided. It is strongly

recommended that either Teflon® tape or

commercial pipe sealant be used at all tapered

fittings and connections. If Teflon® tape is used,

care must be taken that the proper amount is

applied. Excessive tape may fray and cause

plugging of relief valves, orifices, nozzles, etc.

Overuse of pipe sealant may cause similar

problems.

External equipment should also be checked

carefully for leaks. Process connections, flange

bolts, and vents must be tightly closed. Defective

gaskets, leaking valves, and damaged

diaphragms are all potential sources of leaks.

For detection of very small system leaks, the

traditional soap bubble method may not be

sufficient. Halogen leak detection devices may

be required when using highly sensitive pressure

calibration equipment.

Since the pressure change of a contained

volume of gas is directly proportional to absolute

temperature, temperature control is critical when

using the Model PPP-3P with any high-resolution

measuring device. Tubing should be kept away

from heat sources (i.e., lamps, operating

electronic equipment, excessive hand contact,

etc.) as well as from heat-dissipating structures

(i.e., open windows, air conditioning vents,

ventilation ducts, etc.) to minimize temperature

variations that might induce measurement error.

Air is compressed when the Model PPP-3P’s

actuating levers are squeezed. This

compression causes some heating of the air as

it is forced into the system. Consequently, a

noticeable decrease in pressure—caused by the

cooling of the newly compressed air—may occur

immediately after cessation of pumping.

LUBRICATION

The Model PPP-3P is lubricated at the factory

and under normal operating conditions should

not require additional lubrication. If lubrication

is required, invert the pump and apply two drops

of a light-grade machine oil to the piston rod near

the base of the pump body. Do not over-oil.

TEMPERATURE CONSIDERATIONS

-5

-10

LP HP

ALTEK INDUSTRIES CORP

ROCHESTER, NY 14623 USA

APPROVED

PRESSURE INDICATOR

MODEL 620

PRESSUREMODEL 620

WHEN USED WITH NO. 216 BATTERY

INTRINSICALLY SAFE FOR:

CL I DIV 1 GP A B C AND D

CL II DIV 1 GP E F AND G

CL III HAZARDOUS LOCATIONS

NONINCENDIVE FOR:

CL I DIV 2 GP A B C AND D

CL II DIV 2 GP F AND G

CL III HAZARDOUS LOCATIONS

Vent

Differential

Pressure

Transmitter

100

SPECIFICATIONS

OUTPUT RANGE: -2 to 200 psig

RESOLUTION: 0.001 psig

PRESSURE CONNECTIONS

Primary Port: 1/8"-27 NPT

Auxiliary Port: 1/8"-27 NPT

WEIGHT: 0.87 kg (1.9 lb.)

MEDIA COMPATIBILITY: Non-conductive, non-

corrosive, instrument-grade clean air or inert gas

CONSTRUCTION: Machined brass pump body,

piston; stainless steel piston rod, handles

Direct all warranty and repair requests/inquiries to @OMEGA

Customer Service Department. BEFORE RETURNING ANY

PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN

AUTHORIZED RETURN (AR) NUMBER FROM OMEGA'S

CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID

PROCESSING DELAYS). The assigned AR number should then be

marked on the outside of the return package and on any correspon-

dence.

The purchaser is responsible for shipping charges, freight,insurence

and proper packaging to prevent breakage in transit.

FOR WARRANTY RETURNS, please have the following informa-

tion available BEFORE contacting OMEGA:

1. P.O. number under which the product was PURCHASED,

2. Model and serial number of the product under warranty, and

Repair instructions and/or specific problems relative to the product

FOR NON-WARRANTY REPAIRS, consult OMEGA for current

repair charges. Have the following information available BEFORE

contacting OMEGA:

1. P.O. number to cover the cost of repair,

2. Model and serial number of product, and

3. Repair instructions and/or specific problems relative to the prod-

uct.

OMEGA's policy is to make running changes, not model changes,

whenever an improvement is possible. This affords our customers

the latest in technology and engineering.

OMEGA is a registered trademark of OMEGA ENGINEERING, INC.

This document may not be copied, photocopied, reproduced, translated,

or reduced to any electronic medium or machine-readable form, in whole

or part, without prior written consent of OMEGA ENGINEERING, INC.

RETURN REQUESTS / INQUIRIES

OMEGAnetSM On-Line Service Internet e-mail

http://www.omega.com info@omega.com

It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply. OMEGA is con-

stantly pursuing certification of its products to the European New Approach Directives. OMEGA will add the CE mark to

every appropriate device upon certification.

The information contained in this document is believed to be correct but OMEGA ENGINEERING, Inc. accepts no

liability for any errors it contains, and reserves the right to alter specifications without notice.

WARNING: These products are not designed for use in, and should not be used for, paitent connected applications

Servicing North America:

USA: One Omega Drive, Box 4047

ISO 9001 Certified

Stamford, CT 06907-0047

Tel: (203) 359-1660 FAX: (203) 359-7700

Canada: 976 Berger

Laval (Quebec) H7L 5A1

Tel: (514) 856-6928 FAX: (514) 856-6886

For immediate technical or application assistance:

USA and Canada:

Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA

Customer Service: 1-800-622-2378 / 1-800-622-BEST

Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN

TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA

Mexico:

Tel: (95) 800-TC-OMEGA

FAX: (95) 203-359-7807

Servicing Europe:

Benelux:

Postbus 8034, 1180 LA Amstelveen, The Netherlands

Tel; (31) 20 6418405 FAX: 42 (69) 631114

e-mail: nl@omega.com

Czech Republic:

Ostravska 767, 733 01 Karvina

Tel: 42 (69) 6311899 FAX: 42 (69) 631114

e-mail: czech@omega.com

France:

9,Rue Denis Papin, 78190 Trappes

Tel: 33 (1) 30.62.14.00 FAX: 33 (1) 30.69.91.20

Toll Free in France: 05-4-OMEGA

e-mail: france@omega.com

Germany/Austria:

Daimlerstrasse 26, D-75392 Deckenpfronn, Germany

Tel: 49 (07056) 3017 FAX: 49 (07056) 8540

Toll Free in Germany: 0130 11 21 66

United Kingdom:

25 Swannington Road, Broughton Astley, Leicestershire,

ISO 9002 Certified

LE9 6TU, England

Tel: 44 (1455) 285520 FAX: 44 (1455) 283912

Toll Free in England: 0800-488-488

e-mail: uk@omega.com

omega.comTM

OMEGA

TEMPERATURE

✔ Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies

✔ Wire: Thermocouple, RTD & Thermistor

✔ Calibrators & Ice Point References

✔ Recorders, Controllers & Process Monitors

✔ Infrared Pyrometers

PRESSURE, STRAIN AND FORCE

✔ Transducers & Strain Gauges

✔ Load cells & Pressure Gauges

✔ Displacement Transducers

✔ Instrumentation & Accessories

FLOW/LEVEL

✔ Rotameters, Gas Mass Flowmeters & Flow Computers

✔ Air Velocity Indicators

✔ Turbine/Paddlewheel Systems

✔ Totalizers & Batch Controllers

pH/CONDUCTIVITY

✔ pH Electrodes, Testers & Accessories

✔ Benchtop/Laboratory Meters

✔ Controllers, Calibrators, Simulators & Pumps

✔ Industrial pH & Conductivity Equipment

DATA ACQUISITION

✔ Data Acquisition & Engineering Software

✔ Communications-Based Acquisition Systems

✔ Plug-in Cards for Apple, IBM & Compatibles

✔ Datalogging Systems

✔ Recorders, Printers & Plotters

HEATERS

✔ Heating Cable

✔ Cartridge & Strip Heaters

✔ Immersion & Band Heaters

✔ Flexible Heaters

✔ Laboratory Heaters

ENVIRONMENTAL

MONITORING AND CONTROL

✔ Metering & Control Instrumentation

✔ Refractometers

✔ Pumps & Tubing

✔ Air, Soil & Water Monitors

✔ Industrial Water & Wastewater Treatment

✔ pH, Conductivity & Dissolved Oxygen Instruments

Where Do I find Everything I Need for

Process Measurement and Control?

OMEGA...Of Course!

M-3403/0799 100798-903 Rev A

Omega Engineering Ppp3P Users Manual Pressure Pump

PPP3P to the manual 33c7d520-b189-6e64-419a-3e2dd5b84c44

Navigation menu

Versions of this User Manual:

Views

Navigation