Omron Automotive Electronics Korea OKA-200W UNIT ASSY - WIRELESS CHARGING User Manual
Omron Automotive Electronics Korea Co., Ltd. UNIT ASSY - WIRELESS CHARGING
User Manual
USER MANUAL_OKA-200W 1. Constitution of the Unit Assy-Wireless Charging ( WPC ) for vehicle Wireless Charger Unit, it’s possible to charge the receiver based upon WPC( Wireless Power Consortium ) Standard. WPC detects the receiver based upon the WPC standard being put on the surface of charge, and begins to charge it. WPC detects conditions of the receiver and controls the transmission electric power by the state of the battery of it. When the receiver is removed,WPC will suspend the transmission electric power. When the receiver is full charge, WPC will suspend the transmission electric power. WPC can recognize a foreign object and suspend the transmission electric power. Wireless Charger External Ports A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 B_CAN_ B_CAN_ P_LED BLUE SKY P_LED AMBER P_LED GREEN GND_EC LFSearch ing NC GND_PO WER NC ACC B+ Vehicle communication port Vehicle communication port Use of vehicle battery power 2. User's manual (provisionally) ◎ Unit Assy - Wireless Charging ( OMRON KOREA : OKA-200W ) You can charger a mobile phone or the battery pack and the like to Qi-compliant Wireless Charger Unit. ※ Wireless Charger Unit is abbreviated as WPC. Frequency: 111kHz Voltage: 12V DC Power: 5W 1. Once a receiver is placed on the product, it transmits the power wirelessly. 2. The LED connected to the product, signals the status as below. Charging: Amber Discharging: Green Error: Amber Blink Power state of vehicle is ACC or IGN, the product will be stand-by status. If a receiver such as smart phone is not placed properly, it emits Amber LED and receiver must be relocated. 4. Specification 4.1 CONTROL PART 4.1.1 CPU Type uPD78F0567-xxx(8bit) Manufacturer : RENESAS Corporation ROM 256 Kbytes RAM 16 bytes EEPROM 32 bytes Clock frequency 4 MHz Package 80pin SSOP 4.1.2 Others Dimension 39.1mm×70.9mm×17.0mm Weigh about 290 g Battery Car Battery ( DC 12 V ) Operating Voltage, Current DC 12V, 2.0A Transmission Frequency 111 KHz Operation Temperature -30 ℃ ~ 75℃ Support Standard WPC Ver 1.2 4. Specification 4.2 Wireless Charging PART 4.2.1 CPU Type WCT1001A Manufacturer : Freescale ROM 64 Kbytes RAM 8 bytes Clock frequency 8 MHz Package 64pin LQFP 4.1.2 Antenna ( Coil ) Type Dimension 3 Coil Assembly 116.1 mm * 64.01 mm * 5.0 mm 5.Features 5.1 Charging Function WPC possesses the charge function of 3 coils type based upon WPC Ver 1.2. It controls the resonance voltage according to the request from the receiver. It doesn’t change the frequency of the resonance voltage. It judges whether there is a thing on the charge surface by the different amount of the resonance voltage and detec the receiver. 5.2 Foreign Objection Detection WPC monitors the power loss from the resonance voltage and current inside it. WPC judges that there is a foreign object when power loss is beyond the constant value. FCC Part 15.19 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Part 15.21 Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. The equipment is installed in a vehicle with a minimum distance of 20 cm to any direction between the radiator and users. During normal usage, it should be at least 20 cm away from the users. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. IC RF Radiation Exposure Statement This equipment complies with IC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Déclaration d'Industrie Canada sur l'exposition aux radiofréquences Cet équipement est conforme aux limites établies par Industrie Canada en matière d'exposition aux radiofréquences dans un environnement non contrôlé. Cet appareil et son antenne ne doivent pas être colocalisés ou fonctionner en conjonction avec tout autre antenne ou émetteur. Cet équipement doit être installé et utilisé avec une distance minimale de 20cm entre le radiateur et votre corps.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : ghyoon Create Date : 2016:05:19 11:06:51+09:00 Modify Date : 2016:06:28 18:26:24+09:00 Title : Has XFA : No Tagged PDF : No XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Metadata Date : 2016:06:28 18:26:24+09:00 Creator Tool : Microsoft® Office Excel® 2007 Format : application/pdf Creator : ghyoon Document ID : uuid:76289152-567d-4b29-87b7-2b52b3140a67 Instance ID : uuid:2810b5a4-95b7-44ff-96ab-189099da9e11 Producer : Microsoft® Office Excel® 2007 Page Count : 6EXIF Metadata provided by EXIF.tools