Omron Okayama factory WD30B DeviceNet Wireless Unit User Manual WD30ME ai

Omron Corporation Okayama factory DeviceNet Wireless Unit WD30ME ai

Contents

User Manual 1 of 3

62
15
80 35
16
74
85
159
59.5
Unit: mm
66
4.5 dia
7
41
Allows clearance of 62 mm or longer
between the antennas.
Antenna cable length is 2 m.
Radius of 38
or longer
Radius
of 38
or greater
Hole diameter
of 11 mm or
longer
Connector
10.5 dia
Do not bend more
than 40 mm.
13.3
35.8 dia.
39
Cable length: 2000
20
94
115
10.5
1618735-0B
Model WD30-ME/ME01
DeviceNet Wireless Master
Instruction Sheet
ENG
Thank you for purchasing an OMRON product.
Please find you have the product of your interest and read
this User's Guide thoroughly for better understanding before
using this product.
Please keep this User's Guide at hand for quick reference
after having read it through.
The description on DeviceNet Wireless Slave (Model WD30-
SE/SE01) is provided on the back side.
Model WD30-ME Model WD30-ME01
OMRON Corporation
All Rights Reserved
Please read the following manual, as well, for safe and
appropriate use.
• DeviceNet Wireless Unit Operation Manual
(No. M071-E1-01)
IC NOTICE
This device has been designed to operate with an antenna having a maximum
gain of 2.14 dB. Antenna having a higher gain is strictly prohibited per
regulations of Industry Canada. The Required antenna impedance is 50 ohms.
To reduce potential radio interference to other users the antenna type and its
gain should be so chosen that the equivalent isotropically radiated power
(EIRP) is not more than that required for successful communication.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de la classe B est conforme a la norme NMB-003 du
Canada.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help.
This transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter.
Wireless standards have been met for the following countries. The product
cannot be used in any other countries.
Australia, Austria, Belgium, Canada, China (see note), Cyprus, Czech,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Japan, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Singapore, Slovakia, Slovenia, Spain, Sweden,
Switzerland, UK, USA
Note: Channel 51 cannot be used in China. Use channels 2 to 34 or channels
52 to 83.
Use is also prohibited in aircraft or near airports.
Caution
To ensure that the WLAN transmitter complies with current FCC regulations
limiting both maximum RF output power and human exposure to radio
frequency radiation, a separation distance of at least 20 cm must be
maintained between the unit's antenna and the body of the user and any
nearby persons at all times and in all applications and uses.
Precautions for Safe Use
Please observe the following for your safety.
(1) Do not use the device for real-time control (I/O control that
requires the same high-speed response as DeviceNet).
(2) Do not apply excessive vibration or shock, or drop the device
accidentally.
(3) Do not use the device subject to:
• corrosive or flammable gas
• excessive debris and dust
• water, oil, and chemicals
• drastic change in temperature that causes condensation
• static electricity and extreme noise
(4) Do not route the communication cable parallel or close to high-
voltage or strong-current cables.
(5) Do not plug or unplug the connector while the power is supplied
to the communication cable.
(6) Use the communication cable specified in this User's Guide.
(7) Do not allow accidental entry of debris while the cover is open.
(8) Do not mount the device to a location where excessive external
force might be applied or that might be used as a footing.
(9) Fasten the screws with the torque specified in this User's Guide.
(10) Do not use this device in the vicinity of any device that might
malfunction due to the presence of radio waves from this device.
Precautions for Correct Use
(1) Disassembly and modification of this unit are prohibited by Radio
Law and may be subject to a penalty.
(2) Do not take off the certification label of technical conformity.
(3) Make sure to turn off the device before cabling.
(4) Use a two-sided adhesive tape or a string to temporarily secure
the device for mounting adjustment and avoid the damage caused
by dropping.
(5) Do not use the device in a location that is subject to direct sunlight
and extremely high humidity or close to a TV set, a radio, a motor
or drill that emits sparks, a strong magnet, and a fluorescent light.
(6) Do not bend or break the antenna. Do not wind an electrical wire
around the antenna.
(7) Mount the device so as not to make the antenna parallel to an
electrical wire or a metal plate. Mount the device as far from an
electrical wire or a metal plate as possible.
(8) Communication performance depends on the environment. This
device may be interfered by other wireless units that send radio
waves in the same frequency band as this device. Make sure to
perform the tests, such as the mounting test, provided by this
device in advance.
Suitability for Use
OMRON shall not be responsible for conformity with any
standards, codes, or regulations that apply to the combination of
the products in the customer's application or use of the product.
Take all necessary steps to determine the suitability of the
product for the systems, machines, and equipment with which it
will be used.
Know and observe all prohibitions of use applicable to this
product.
NEVER USE THE PRODUCTS FOR AN APPLICATION IN-
VOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT
ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DE-
SIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON
PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE
INTENDED USE WITHIN THE OVERALL EQUIPMENT OR
SYSTEM.
• This User's Guide provides information required for using
DeviceNet Wireless Unit. Please read this User's Guide and
"DeviceNet Operation Manual" for better understanding and
appropriate use before using this device. Also, please keep this
User's Guide at hand for quick reference.
Specifications
General specifications
DeviceNet communications power supply voltage
Rated voltage 24 VDC
Allowable voltage range 11 to 25 VDC
(provided from the DeviceNet network power supply)
Power consumption 4 W
Ambient operating temperature -10 to +50˚C
Ambient operating humidity 25 to 85%
Ambient storage temperature -20 to +65˚C
Weight Approx. 200 g
Cabling
DeviceNet communications cable
Use the DeviceNet exclusive cable with a single socket
(Model DCA1-5CN@@F1).
Antenna
Use the supplied two antennas.
Make sure to attach both antennas. With a single
antenna only, the diversity effect is not available.
Radio waveform
Communications method
Frequency band
Number of channels
Antenna power
Wireless interval data transfer speed
Wireless interval protocol
Transmission format
Expected transmission distance
Number of connectable Wireless Slaves
Wireless interface specifications
Spectrum diffusion (direct diffusion: DS-SS)
Simplex (half-duplex)
2.4-GHz band (2402.2 to 2480.2 MHz)
66 channels (using frequency division)
10 mW/MHz
100 kbps
1: N polling selecting method
HDLC compliant
Indoors: 50 m (The transmission distance
depends on the environment.)
The transmission distance can be extended
using relays. (3 stages max.)
64 units
Package Contents
Wireless unit ···············································································1
Instruction Sheet ···········································································3
Screw (with nut) ············································································2
Declaration of Conformity·······························································1
Notification Sheet ···········································································1
Pencil-type antenna ·······································································2
Magnet-base antenna ····································································2
(ME)
(ME01)
DeviceNet interface specifications
Communications functions
Master/Slave Connection Remote I/O functions
Explicit messaging functions
Mounting
Mounting requirement
Fasten the screws with torque of up to
0.3 N·m (2.7 in·lb).
External terminal/connector
Antenna connector
SMA connector
Two antennas are supplied.
Communications connector
DeviceNet communications connector (plug),
DeviceNet micro-connector compliant
Dimensions Mounting
Use the screw to mount the two locations shown in the figure below.
* You can mount ME01 main unit inside by attaching the magnet-base antennas outside.
WD30-ME01 supplied antenna
<WD30-AT001 (magnet-base antenna)>
Available model: WD30-ME/ME01
Unavailable model: WD30-M
Component names and functions
This LED is unlit in RUN mode. When errors are detected, this LED displays the error code and the
error node of the errors in the order of error detections. In TEST mode, this LED displays the received
wave level.
7-segment LED
Use this switch to set up the communications speed and the status of the DeviceNet interface.
Set the switch before power-on. Only the switch setting immediately after power-on is effective. Any
changes to the switch setting after power-on will be ignored.
DeviceNet setup switch [SW1]
MS (Module Status) : Main unit status
NS (Network Status) : DeviceNet network status
WS (Wireless Status): Wireless network status
Status LED
Status LED
7-segment LED
NNODE
switch
DeviceNet setup
switch
Mode selection
switch
Push button
WNODE
switch
WCH
switch
Wireless
setup switch
No. Description
1 Communications (MODE1)
2speed selection (MODE2)
3With/without status
4Maximum IN/OUT count
DeviceNet communications speed setup
Communications
speed (bps)
State of the dip switch
12
MODE1 MODE2
Remarks
125k OFF OFF Trunk length distance of 500 m
250k ON OFF Trunk length distance of 250 m
500k OFF ON Trunk length distance of 100 m
−ON ON Setup prohibited, no communications
No. Description ON OFF
3
4
With/without status With status Without status
Maximum IN/OUT count 1600/1600 512/512
Use this switch to set up operation mode of Wireless Master. (3 positions)
Mode selection switch
Operation mode SW status
Run mode RUN
Test mode TEST
Setup mode SET
Push this button to trigger individual settings in SET mode.
Push button [SW2]
Use this switch to set up the node address (NNODE) of the DeviceNet interface. Set the switch
before power-on. Only the switch setting immediately after power-on is effective. Any changes to the
switch setting after power-on will be ignored.
NNODE switch
Use this switch to set up the node address of the wireless interface.
Wireless Master ignores this switch setting in RUN mode and uses the node address of "00".
Set the switch before power-on. Only the switch setting immediately after power-on is effective. Any
changes to the switch setting after power-on will be ignored.
WNODE switch
Use this switch to set up the group address of the wireless interface and the communications
channel. Set a decimal number from "02" to "34", "51" to "83".
Channel 51 cannot be used in China. Use channels 2 to 34 or channels 52 to 83.
Setting any out-of-range number in RUN mode will cause a switch setup error.
Set the switch before power-on. Only the switch setting immediately after power-on is effective. Any
changes to the switch setting after power-on will be ignored.
WCH switch
Use this switch to set up parameters for TEST and SET modes.
Set the switch before power-on. Only the switch setting immediately after power-on is effective. Any
changes to the switch setting after power-on will be ignored.
Wireless setup switch [SW3]
No. Description ON OFF
1(Always OFF) −−
2(Always OFF) −−
3Wireless channel monitoring NoYes
4Mounting test NoYes
5Confirmation test NoYes
6Wireless Slave registration NoYes
7Wireless Slave removal NoYes
8Default configuration NoYes
Always use a Class 2 power supply to conform to UL standards.
Use a DC power line less than 3 m to conform to EN standards. If a
power line of 3 m or longer is required, extend the length at the
Switching Power Supply's primary side (i.e., the AC power line).
Conformity to Safety Standards
Dansk
[Danish]
Deutsch
[German]
Eesti
[Estonian]
English
Español
[Spanish]
Français
[French]
Italiano
[Italian]
Latviski
[Latvian]
Nederlands
[Dutch]
Malti
[Maltese]
Magyar
[Hungarian]
Polski
[Polish]
Português
[Portuguese]
Slovensko
[Slovenian]
Slovensky
[Slovak]
Suomi
[Finnish]
Svenska
[Swedish]
Íslenska
[Icelandic]
Norsk
[Norwegian]
Undertegnede Omron Corporation erklærer herved, at
følgende udstyr WD30 overholder de væsentlige krav og
øvrige relevante krav i direktiv 1999/5/EF.
Hiermit erklärt Omron Corporation, dass sich das Gerät WD30
in Übereinstimmung mit
den g
rundlegenden Anforderungen
und den übrigen einschlägigen Bestimmungen der Richtlinie
1999/5/EG befindet.
Käesolevaga kinnitab Omron Corporation seadme WD30
vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud
direktiivist tulenevatele teistele asjakohastele sätetele.
Hereby, Omron Corporation, declares that this WD30 is in
compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Por medio de la presente Omron Corporation declara que el
WD30 cumple con los requisitos esenciales y cualesquiera
otras disposiciones aplicables o exigibles de la Directiva
1999/5/CE.
Par la présente Omron Corporation déclare que l’appareil
WD30 est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 1999/5/CE.
Con la presente Omron Corporation dichiara che questo
WD30 è conforme ai requisiti essenziali ed alle altre
disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Šiuo Omron Corporation deklaruoja, kad šis WD30 atitinka
esminius reikalavimus ir kitas 1999/5/EB Direktyvos
nuostatas.
Hierbij verklaart Omron Corporation dat het toestel WD30 in
overeenstemming is met de essentiële eisen en de andere
relevante bepalingen van richtlijn 1999/5/EG.
Alulírott, Omron Corporation nyilatkozom, hogy a WD30
megfelel a vonatkozó alapvetõ követelményeknek és az
1999/5/EC irányelv egyéb elõírásainak.
Omron Corporation declara que este WD30 está conforme
com os requisitos essenciais e outras disposições da Directiva
1999/5/CE.
Omron Corporation vakuuttaa täten että WD30 tyyppinen laite
on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä
koskevien direktiivin muiden ehtojen mukainen.
Härmed intygar Omron Corporation att denna WD30 står l
överensstämmelse med de väsentliga egenskapskrav och
övriga relevanta bestämmelser som framgår av direktiv
1999/5/EG.
Hér með lýsir Omron Corporation yfir því að WD30 er í
samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í
tilskipun 1999/5/EC.
Omron Corporation erklærer herved at utstyret WD30 er i
samsvar med de grunnleggende krav og øvrige relevante krav
i direktiv 1999/5/EF.
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Omron Corporation ∆ΗΛΩΝΕΙ ΟΤΙ WD30
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ
ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ
1999/5/EK.
Cesky
[Czech]
Omron Corporation tímto prohlašuje, ze tento WD30 je ve
shode se základními pozadavky a dalšími príslušnými
ustanoveními smernice 1999/5/ES.
Ελληνικη
[Greek]
Lietuviu
[Lithuanian]
Hawnhekk, Omron Corporation, jiddikjara li dan WD30
jikkonforma mal-htigijiet essenzjali u ma provvedimenti ohrajn
relevanti li hemm fid-Dirrettiva 1999/5/EC.
Omron Corporation izjavlja, da je ta WD30 v skladu z bistvenimi
zahtevami in ostalimi relevantnimi dolocili direktive 1999/5/ES.
Omron Corporation týmto vyhlasuje, ze WD30 splna základné
poziadavky a všetky príslušné ustanovenia Smernice
1999/5/ES.
Niniejszym Omron Corporation oswiadcza, ze WD30 jest
zgodny z zasadniczymi wymogami oraz pozostalymi
stosownymi postanowieniami Dyrektywy 1999/5/EC.
Ar šo Omron Corporation deklare, ka WD30 atbilst Direkt vas
1999/5/EK butiskajam pr
as bam un citiem ar to
saist tajiem
noteikumiem.

Navigation menu