Omron Okayama factory WT30 Wireless SS Terminal WT30-M01-FLK User Manual front eps
Omron Corporation Okayama factory Wireless SS Terminal WT30-M01-FLK front eps
manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 507102 |
| Application ID | vq9tsGqAvXK1R2O04rXDQA== |
| Document Description | manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 45.81kB (572638 bits) |
| Date Submitted | 2005-01-18 00:00:00 |
| Date Available | 2005-01-18 00:00:00 |
| Creation Date | 2005-01-14 07:52:47 |
| Producing Software | Acrobat Distiller 5.0 (Windows) |
| Document Lastmod | 2005-01-18 14:00:28 |
| Document Title | front.eps |
| Document Creator | AdobePS5.dll Version 5.2.2 |
Suitability for Use WARNING Finnish Omron Corporation vakuuttaa täten että WT30 tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Dutch Bij deze verklaart Omron Corporation dat deze WT30 voldoet aan de essentie"le eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC. French Par la présente Omron Corporation déclare que l'appareil WT30 est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Par la présente, Omron Corporation déclare que ce WT30 est conforme aux exigences essentielles et aux autres dispositions de la directive 1999/5/CE qui lui sont applicables. Precautions for Safe Use Be sure to observe the following precautions to ensure safe use of the product. 1) Transport the product in the box in which the product was packaged, making sure the product is not subjected to excessive vibrations or shock, or dropped. Härmed intygar Omron Corporation att denna WT30 står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. 2) Store the product within the specified environment. Allow the product to warm up to room temperature for at least 3 hours after it has been stored at −10 °C or lower. Danish Härmed intygar Omron Corporation att denna WT30 står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. German Hiermit erklärt Omron Corporation, dass sich dieser/diese/dieses WT30 in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet". (BMWi) 4) Do not use the product in the following locations. Locations subject to extreme temperature changes resulting in condensation Locations subject to static electricity, excessive noise, or electric fields Locations where the product may come into contact with water, oil, or chemicals Locations where corrosive gases or flammable gases are present Locations where large amounts of dust or dirt are present Locations subject to spatters, iron chips, or filings Swedish Hiermit erklärt Omron Corporation die Übereinstimmung des Gerätes WT30 mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG. (Wien) Greek WT30 3) Use the product within the specified temperature and humidity ranges. 5) Do not install the product outdoors (outside a control panel). 6) Use tape, cord, or other means to hold the product while adjusting the installation position to prevent the product from damage due to falling. 7) Do not install the product in areas where it will be subject to excessive external force, or in walkways. 8) Tighten the mounting screws to the specified torque of 0.5 to 0.6 N·m. Alulírott, Omron Corporation nyilatkozom, hogy a WT30 megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Czech Omron Corporation tímto prohlašuje, e tento WT30 je ve shode se základními po adavky a dalšími príslušnými ustanoveními smernice 1999/5/ES. Polish 15) Use communications cables (RS-232C cables) with a length of 15 m maximum and a load of 2,500 pF maximum. 16) Do not lay communications cables (RS-232C cables) and antenna cables near other high-voltage cables or power lines. Wireless standards have been met for the following countries. The product cannot be used in any other countries. 19) Always set the product after it is installed or replaced. Set the product correctly according to the manual, and be sure to perform the tests provided with the product (e.g., communications tests) before operating it. Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungry, Iceland, Ireland, Italy, Japan, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland, UK, USA 20) When operating the product without checking serial numbers, check whether an existing system is present, and design the system carefully to prevent radio interference. 21) Do not apply excess vibrations or shock to this product. Do not drop this product. Caution To ensure that the WLAN transmitter complies with current FCC regulations limiting both maximum RF output power and human exposure to radio frequency radiation, a separation distance of at least 20 cm must be maintained between the unit's antenna and the body of the user and any nearby persons at all times and in all applications and uses. Note: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 22) Make sure that wiring and switch settings are correct before starting operations. 23) Other wireless devices operating within the same frequency band may interfere with this product or be adversely affected by this product. Therefore, be sure to perform the tests provided with the product (e.g., installation tests) before operating it. 26) Turn OFF the power supply before performing any wiring or replacing devices. 27) Do not touch the product with wet hands. 28) Dispose of the product as industrial waste. For PLC (2) Pull section A to the right and lower while compressing the spring. (1) Insert the end of section A into the base of the Adapter. Note: Tighten the WT30 mounting screws using the specified torque of 0.5 to 0.6 N·m. Mounting Method Specifications Hook the top of the WT30 over the DIN Rail. Ratings Rated voltage Power supply (wireless communications Allowable power supply) voltage range Power consumption Error output/ Rated voltage output power Allowable supply (for output circuits) voltage range (1) DIN Rail WT30-SID16/SMD16/ SMD16-1 I/O Slaves WT30-M01-FLK Serial Master Item 24 VDC Note: Remove the dust-proof label after mounting. (2) 20.4 to 26.4 VDC 3 W max. Removal Method --- 24 VDC --- 20.4 to 26.4 VDC MAIN Unhook the WT30 from the DIN Rail. (2) DIN Rail SUB PWR 90 1 MCA 2 11 21 WS MS ERR COMM UNIT No. MODE RUN TEST SET W NODE 90 1 x10 x1 ON 90 1 RSSI W CH 90 1 x10 90 1 x1 RS-232C MODE FUNCTION 90 1 x10 x1 ENTER ON OFF ON 24VDC Insulation resistance Dielectric strength 20 MΩ min. (at 100 VDC) between the 20 MΩ min. (at 100 VDC) power supply and all I/O and I/O power between the power supply supply and between the power supply and chassis and chassis 1,500 VAC for 1 min between the 1,500 VAC for 1 min between power supply powersupply and all I/O and I/O power supply and between the and chassis power supply and chassis IEC61000-4-4. 1 kV (power supply line) Noise immunity Vibration resistance Shock resistance Using a Surface Mounting Bracket Mounting hole dimensions (Unit: mm) D-sub, 9-pin (female) Inch screws (OMRON XM2F0910-132 or equivalent) 5 dia. ANT1 ANT2 WT30- Number of simultaneously ON I/O points 10 max.: −10 to 55 ˚C 16 max.: −10 to 50 ˚C (with the Terminal mounted with the dust-proof label facing up) Ambient operating humidity 25% to 85% (with no condensation or icing) No corrosive gases Ambient environment −25 to 65 °C (with no condensation or icing) Storage temperature IP20 Degree of protection Screwless terminal block Terminal Power (Phoenix Contact FFKDS/V1-5.08 or equivalent) construction supply Serial (1) Pull the bottom side forwards. Insert a flat-blade screwdriver or other tool into the lower hook and pull down. Mounting hole Conforms to JIS C0041: 300 m/s2 3 times each in X, Y, and Z Ambient operating temperature RS-232C WT30 JIS C0040 Frequency: 10 to 55 Hz; Amplitude of 0.35 mm or acceleration of 50 m/s2, whichever is smaller (DIN Rail mounting: single-amplitude of 0.1 mm or acceleration of 15 m/s2) 10 sweeps of 8 min each (i.e., 80 min in total) in X, Y, Z directions −10 to 55°C (with the Terminal mounted with the dust-proof label facing up) 24) Make sure that the antenna is not disconnected during operation. 25) Do not use this product near other devices that may malfunction due to the electromagnetic waves emitted by this product. (3) Position the Adapter on the WT30 and secure with screws. Insert spring Type DIN Rail Mounting Bracket (for TH35-7.5) DIN Rail Mounting Bracket (for TH35-15) Surface Mounting Bracket (screw-mounting) (2 brackets per set) Flat Diversity Antenna Mounting Brackets (with magnets) Antenna Extension Cable (1 cable, 2 m) 17) Use the specified cables for communications cables (RS-232C cables). 18) Be sure to perform communications tests to confirm operation after wiring before using the product. FCC Notice This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Model WT30-FT001 WT30-FT002 WT30-FT003 WT30-FT011 WT30-CA2M 12) Use the correct power supply voltage. 14) Do not apply voltage to the inputs exceeding the rated voltage range. Using a DIN Rail Adapter (Installation Tool: WT30-FT001 or WT30-FT002) Other 11) Do not reverse the power supply connection or connect the product to an AC power supply. 13) Use AWG22 to AWG16 to connect wires for post terminals. For solid or standard wires, however, use AWG20 to AWG16 (0.52 to 1.5 mm2). The length of exposed wire is 10 mm. Application For personal computer 23 Hungarian WT30-AT003 Length 1 m 2m 5m 2m 5m 23 Norweigian Omron Corporation erklarer herved, at følgende utstyr WT30 overholder de vesentlige krav og øvrige relevante bestemmelser i direktiv 1995/5/EF. WT30-AT002 Model XW2Z-0100U-3 XW2Z-0200U-3 XW2Z-0500U-3 XW2Z-0200U-5 XW2Z-0500U-5 23 Omron Corporation declara que este WT30 está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. 10) Do not install the product in walkways or locations subject to traffic when installing the product outside a control panel. Type Magnet-base Antenna (2 antennas per set) Flat Diversity Antenna (1 antenna) Pencil Antenna (2 antennas per set) 23 Portugues Por medio de la presente Omron Corporation declara que el WT30 cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. 9) Provide sufficient space around the product for heat dissipation. Communications Cables Model WT30-AT001 23 Spanish Con la presente Omron Corporation dichiara che questo WT30 è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Accessories Antennas 23 Italian Using a DIN Rail Note: Do not install the product in a metal panel. Doing so will decrease the wireless performance. To install the product in a panel, use either a Magnet-base Antenna or Flat Antenna and install the Antenna on the outside of the panel. Note: An Antenna is not included with the FA Wireless SS Terminals. 78 Hereby, Omron Corporation, declares that this WT30 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Terminal labels (slaves only) Adhesive non-slip feet (master only) Installation 78 English Type Specifications (No. of I/O points) Serial Master RS-232C 16 DC inputs (NPN/PNP) I/O Slaves 8 DC inputs (NPN/PNP) + 8 transistor outputs (NPN) 8 DC inputs (NPN/PNP) + 8 transistor outputs (PNP) 78 Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or in property damage. Make sure that the direction and polarity (+/-) are correct when connecting terminal blocks and connectors. Turning ON the power to I/O circuits with the I/O cables connected in reverse, may result in a blown output fuse. Do not apply a voltage or connect a load to the outputs that exceeds the maximum switching capacity. Leave the protective label in place when wiring the product. After completing wiring, always remove the protective label to enable proper heat dissipation. Fire may occasionally result if this precaution is not observed. Do not allow pieces of metal, wire clippings, or fine metallic shavings or filings from installation to enter the product. Doing so may occasionally result in minor electric shock, fire, or malfunctions. Do not attempt to disassemble, repair, or modify the product, or touch the internal parts of the product. Doing so may occasionally result in minor electric shock, fire, or malfunctions. In Japan, disassembly and modification is also prohibited under Japan's Radio Law and may be punishable by law. CRC-CCITT (16 bits) Package Contents 78 CAUTION Indicates a potentially hazardous situation which, if not avoided, will result in minor or moderate injury, or may result in serious injury or death. Additionally there may be significant property damage. CAUTION WT30-M01-FLK WT30-SID16 WT30-SMD16 WT30-SMD16-1 64 max. WT30 FA Wireless SS Terminal Instruction Sheet 78 WARNING Available Models 10 sets max. (recommended) Using the FA Wireless SS Terminal near a pacemaker or other medical device may affect the operation of the medical device, possibly resulting in serious injury. Never use the FA Wireless SS Terminal near pacemakers or other medical devices. Definition of Precautionary Information Use a DC power line less than 3 m to conform to EN standards. If a power line of 3 m or longer is required, extend the length at the Switching Power Supply’s primary side (i.e., the AC power line). WT30 Terminal model Do not use this product for real-time control. Safety Precautions Always use a Class 2 power supply to conform to UL standards. One stage using I/O slave for the serial master configuration. Design the system to ensure safety in the event of temporary interruptions in communications due to interference with the electromagnetic waves used for communications caused by the ambient environment and application methods. Conformity to Safety Standards 100 kbps Relay functions 78 Always provide protective circuits in the network. Without protective circuits, malfunctions may possibly result in accidents that cause serious injury or significant property damage. Provide double or triple safety measures in external control circuits, such as emergency stop circuits, interlock circuits, or limit circuits, to ensure safety in the system if an abnormality occurs due to malfunction of the product or another external factor affecting the product's operation. 67 channels (based on switching) 10 mW/MHz Number of stations per area Number of I/O Slaves connected Error detection method For detailed application procedures, refer to the WT30 Operation Manual (Cat. No. N138). Precautionary Information 2,401 to 2,480.2 MHz Number of channels Transmitter output power Baud rate between wireless stations 1617569-7A T1 See also Product catalog for Warranty and Limitation of Liability. Simplex Frequency band 40 Thank you for purchasing this OMRON product. Read this instruction sheet and thoroughly familiarize yourself with the functions and characteristics of the product before using it. This product is designed for use by qualified personnel with knowledge of electrical systems. Keep this instruction sheet for future reference. Spread Spectrum (direct sequence; SS-DS) Communication method 456 Instruction Sheet Specifications Wave type 456 ENG NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Item 456 Know and observe all prohibitions of use applicable to this product. FA Wireless SS Terminals Always heed these precautions to prevent faulty operation, malfunction, or adverse affect on the product's performance and functionality. 1) Communications performance will vary according to the operating environment. Always check operations before using the product. 2) Do not install the antenna in a location surrounded by metal, such as in a control panel. 3) Install the antenna so that it is as far away as possible from and not parallel to electric wires or metal plates. 4) Do not use this product in areas exposed to extremely high humidity, near televisions or radios, near motors or drills that emit sparks, near strong magnets, or near fluorescent lights. 5) Make sure that the terminal blocks, communications cables (RS-232C cables), and other items with locking devices are properly locked into place. 6) Do not pull or bend cables with force. 7) Do not change the mode selection switch during operation. 456 Model WT30 Wireless Interface Specifications Precautions for Correct Use 456 OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of the products in the customer's application or use of the product. Take all necessary steps to determine the suitability of the product for the systems, machines, and equipment with which it will be used. 456 FCC ID: RXEWT30 M01-F LK 120 Serial Master Station Table-top Mounting Adhesive non-slip feet WT30-FT003 Surface Mounting Bracket Note: Tighten the WT30 mounting screws using the specified torque of 0.5 to 0.6 N·m. --- Weight 330 g max. EEPROM write life Approx. 1 million writes Note: Use the WT30-FT003 Surface Mounting Bracket when installing the WT30 in environments subject to vibration. Attach the adhesive non-slip feet to the bottom of the WT30 and stand the WT30 on a flat surface. Names of Parts Function Setting Switch Serial Master Station Serial Master Station Unit No. switch Set the unit number of the Serial Master Station. Default value: 00 Node setting switch (WNODE) Set the number of connected I/O Slave Stations. Default value: 01 Channel setting switch (WCH) Set the communications frequency. Default value: 02 Antenna terminal (ANT2) COMM MS WS UNIT No. W NODE RSSI W CH MODE ENTER x10 x1 x10 ON x1 x10 x1 ON OFF ON RS-232C MODE RUN TEST SET Serial Communications Setting Switch Set the baud rate, and other communications settings. Power supply terminal Supply power to the Unit. Received signal strength indicator Special function switch SET mode Function setting switch Make the detailed settings for RUN/TEST/SET mode. Not used 10 I/O Slave Station Node setting switch (WNODE) Set the unit number of the I/O Slave Station. Default value: 01 I/O terminal status indicators (o to 7 or 8 to 15) The contact status is displayed. Channel setting switch (WCH) Set the communications frequency. Default value: 02 Antenna terminal (ANT1) IN WS 78 78 456 78 456 456 24 VDC 0 V 8 Power supply terminal Supply power to the Unit. 10 9 01 x10 ENTER ON OFF x1 IN 3 COM 4 IN 11 COM 12 13 Received signal strength indicator Special function switch FUNCTION 14 15 COM ERR(P) COM ERR(N) WT30SID16 Function setting switch Make the detailed settings for RUN/TEST/SET mode. I/O terminals Connect the contact signals. Dimensions Common Dimensions for Serial Master and I/O Slave Stations 105 85 8.1 150 Cable bending angle and dimensions 34 ANT1 40 8.9 67 67 45 x1 ON OFF R38 FUNCTION 7 to 10 OFF functions Clears I/O status data when a communications error occurs. Normal mode Input filter: 10 ms Signal strength monitor enabled Specified channel selected Installation test function Nothing done Not used --- For example, if pins number 2, 3, and 4 are all ON, the total is 7, which corresponds to a baud rate of 115,200 bps. Weak 20 Number of levels 45 45 7.3 Display RSSI MS (Module Status) Lit Serial communications in progress. No serial communications. Yellow Not lit Lit/ Not lit ON/OFF status for input or output signals Green Red --- A fatal error has occurred that cannot be recovered from. Replace the WT30 Terminal. Flashing A non-fatal error has occurred that can be recovered from by resetting the system. Not lit Power is not being supplied or the system is resetting. Lit The station has joined the wireless network. to join wireless network received from Serial Flashing Permission Master Station (Slave Stations) Lit A fatal error has occurred that cannot be recovered from. Flashing Error from which recovery is possible Lit Not lit Wireless communications are not in progress. · Use a tool of the appropriate size to crimp the post terminal. Make an incision in the cable and remove the covering so that the cable is either the same length as or approximately 0.5 mm longer than the post terminal, as shown in the following diagram. Make sure that no stray wires are protruding and the post terminal is not damaged. COM ERRP 10 11 COM 12 13 14 15 Error output (NPN) Inputs COM 4 Medium Strong 24 VDC 0 V Range in which specified channel can be used. Installation/ confirmation test Unstable communications range Stray wire Insufficient length removed COM ERRP 2401.0 51 2402.2 2403.4 52 2404.6 2405.8 53 2407.0 2408.2 54 2409.4 2410.6 55 2411.8 2413.0 56 2414.2 · · · · · · · · · · · · · · · · · · · · · · 32 2475.4 82 33 2477.8 34 2480.2 83 Channels 35 to 50 cannot be set. : The shaded channels cannot be used in China. · 2476.6 2479.0 Dust-proof Label COMERRN Error output (NPN) MAIN ERR RUN TEST SET MS MCA 2 11 21 WS RSSI W CH ENTER x10 x1 x10 x1 ON OFF ON FUNCTION 24 VDC 20.4 to 26.4 VDC 4.7 kΩ (typical) 5 mA (typical) 17.4 VDC, 3.0 mA min. EC DECLARATION OF CONFORMITY 5.0 VDC, 1.0 mA max. Error Output Circuit Diagram IN 0 IN 1 IN 2 IN 15 Fuse Fuse COM (IN) ERRP ERRN We hereby declare that the following product is in conformity with the requirements of the following ED Directive: Product: Wiress SS Terminals Type: WT30 series with/without ANTENNA AT-001, AT002 or AT003, Antenna Extension Cable WT30-CA2M in connection with the Wiress Terminals No. of Directive: 99 /5 / EC Title of Directive: Radio and Telecommunications Terminal Equipment No. of Directive: 89 / 336 / EEC Title of Directive: Electromagnetic Compatibility No. of Directive: 73 / 23 / EEC Title of Directive: Low Voltage Equipment This product is designed and manufactured in accordance with the following standards. R&TTE: EN 300 440-2 V1.1.1 EN 50371: 2002 EMC: EN 301 489-3 V1.4.1 EN 301 489-17 V1.2.1 EN 60950-1: 2001 Safety: Year which the CE marking is affixed: 2005 Manufacturer: Omron Corporation, Wireless Components Department Name: Address: Shiokoji Horikawa, Shimokyo-ku, Kyoto, 600-8530 Japan Date: Signed: Representative in EU: Name: Omron Europe B.V. Address: Output Circuit Diagram (PNP) Output Circuit Diagram (NPN) Remove the dust-proof label after completing wiring. SUB PWR Specifications WCH setting Center frequency (MHz) x 10 x 1 COM Outputs Input Circuit Diagram Frequency Table 10 ms/100 ms (Depends on the software used. Selected using switch.) Input voltage 24 VDC Allowable voltage range 20.4 to 26.4 VDC 100 mA max. per output (at 20.4 to 26.4 VDC) Max. switching Simultaneous usage of error output NPN/PNP is not possible. current Leakage current 0.1 mA max. Residual voltage 1.0 V max. One for every two outputs except for error output circuits, Fuse which have one for every NPN/PNP output. (No fuses can be replaced by the user.) The received signal strength is indicated using 10 levels. Check the communications status, referring to the field strength level. MODE Item Input voltage Allowable voltage range Input impedance Input current ON voltage/current characteristics OFF voltage/current characteristics Input filter Stable communications range W NODE Range in which specified channel cannot be used. WCH setting Center frequency CH (MHz) x 10 x 1 Power supply Stable communications range Unstable communications range Field strength monitor CH Surface damage Incorrect Example Error output (PNP) Inputs Insert a screwdriver into the screwless terminal block as shown below, and keeping the screwdriver inserted, pull out the post terminal. COM ERRN Attach terminal labels to the positions shown in the following diagram. Error output OFF Flashing TEST mode or SET mode has been activated. --WS (Wireless Status) Error output ON: Wireless device error or wireless communications error. Red/ Received Signal Strength Indicator monitor: Number of Lit/ Yellow/ All not lit indicators lit (received signal strength 1 to 9) Green Received signal strength less than 0 to 1. Green Lit Communications are normal. Red WT30-SMD16 Error output/output WT30-SMD-16-1 power supply Fuse Zilverenberg 2, 5234 GM's Hertogenbosch The Netherlands Date: OUT 0 Secondary internal circuit 0 to 15 (I/O Slave Station) Yellow 0V Secondary internal circuit (Unit: mm) ERR (I/O Slave Station) COMM (Master Station) COM Power supply TEST mode WT30-AT001 WT30-AT002 Meaning (primary error) Power is being supplied. Power is not being supplied. Attaching Terminal Labels (I/O Slaves Only) OFF ON Detailed settings Default settings (baud rate: 9,600 bps; data length: 7 bits; (settings for No. 2 parity: even; stop bits: 2) to 8 used) Settings for No. 2 to 8 are ignored. Baud rate (bps) (See note.) 1 Total value = 0: 1,200 = 1: 2,400 = 2: 4,800 = 3: 9,600 = 4:19,200 = 5: 38,400 = 6: 57,600 = 7: 115,200 7 bits 8 bits Data length Parity None Yes Odd Even Stop bits 1 bit 2 bits WT30-M01-FLK Color Status Green Lit Not lit Lit Red Not lit 0 to 0.5 mm 24 VDC Function No. 1 Communications setting selection RUN mode Indicator PWR --- RS-232C 24 VDC 0 V Correct Example ON functions Holds I/O status data when a communications error occurs. Input hold Input filter: 100 ms Signal strength monitor disabled All channels automatically selected Field strength R50 40 Error output (PNP) Inputs --- Received Signal Strength Indicator ENTER x10 67 67 45 45 12 3 ON RS-232C MODE RSSI 809 809 x1 Error output power supply W CH 809 x10 12 3 x1 12 3 12 3 67 W NODE 12 3 12 3 ON WS 809 809 x10 67 MS UNIT No. 809 45 COMM TEST mode Note: 23 ANT2 PWR MODE RUN TEST SET RUN mode x1 23 23 9 01 23 23 ON W CH 9 01 x10 78 W NODE 9 01 RUN TEST SET RSSI 456 MS ERR MODE Mode selection switch Antenna terminal (ANT2) 8 9 10 1 1 12 13 14 15 ANT2 PWR Cable (AWG24 to AWG16) single/stranded wire (0.2 to 1.5 m2) · I/O Slave Station Serial Communications Setting Switch 0 1 2 3 4 5 6 7 ANT1 10 mm Length of exposed wire I/O Characteristics WT30-SID16 Nothing done Registers all I/O Slaves automatically Ignores serial numbers Wire the signal lines separately from power lines to prevent noise interference. Do not lay wiring close to the antenna. Turn OFF the power before performing any wiring. Wire the terminals using the following post terminals and cables. I/O Slave Station RS-232C Terminal Connect the PLC, personal computer, etc. 9876 Wiring Precautions Note: The serial number refers to the product's unique number. No. Applicable mode WT30-M01-FLK Status indicators Scan list recognition Registers specified I/O Slave Recognizes serial numbers (See note.) --- FUNCTION RS-232C 24 VDC 0 V Relays not used Signal strength monitor disabled Signal strength monitor enabled All channels automatically Specified channel selected selected ----- Secondary internal circuit PWR TEST mode OUT 1 Fuse OUT 2 Fuse Secondary internal circuit Status indicators Mode selection switch ANT2 RUN mode Input Characteristics ANT1 54321 OFF functions Clears I/O status data when a communications error occurs. Disables scan list ON functions Holds I/O status data when a communications error occurs. Enables scan list Relays used Output/Error Output Characteristics Antenna terminal (ANT1) Applicable mode D-sub, 9-pin, Female End at WT30 Pin No. Signal I/O direction ----1 RD Output SD Input ----4 --5 SG ----6 --7 ------8 ----9 • RS-232C Connector OUT 0 OUT 1 Fuse OUT 2 OUT 3 OUT 7 Fuse OUT 7 • Contact Address (North America) OMRON ELECTRONICS LLC (OEI) Phone: 1-847-843-7900 or 1-800-55-OMRON (Europe) OMRON Europe B.V. (OEE) Phone: 31-2356-81-300
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 2 Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:524a524e-9c15-4b58-8fe1-c2d3db72845c Producer : Acrobat Distiller 5.0 (Windows) Create Date : 2005:01:14 07:52:47Z Modify Date : 2005:01:18 14:00:28+01:00 Metadata Date : 2005:01:18 14:00:28+01:00 Creator Tool : AdobePS5.dll Version 5.2.2 Document ID : uuid:930de4b3-270f-4b71-86e4-db4dde11e01b Format : application/pdf Title : front.eps Creator : AdobePS5.dll Version 5.2.2EXIF Metadata provided by EXIF.tools