Onkyo Home Entertainment LS3100 BT Module User Manual Users manual

Onkyo Corporation BT Module Users manual

UserManual.wiki >

Onkyo Home Entertainment >

LS3100 User Manual >

Users manual HTML Version

1. Installation manual
2. Users manual

Users manual

Living Speaker System

LS3100

Sound System Controller (LAP-301)

Front Speakers (SLM-301)

Wireless Subwoofer (SLW-301)

Instruction Manual

Thank you for purchasing an Onkyo product. Please read this

manual thoroughly before making connections and plugging

in your new Onkyo product.

Following the instructions in this manual will enable you to

obtain optimum performance and listening enjoyment from

your new product.

Please retain this manual for future reference.

Contents

Before Use.........................2

Connections ....................14

Operations.......................17

Useful Function...............21

Appendix..........................22

E52_LS3100_120910.book 1 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

Before Use

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce

heat.

9. Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has

two blades with one wider than the other. A

grounding type plug has two blades and a third

grounding prong. The wide blade or the third

prong are provided for your safety. If the

provided plug does not fit into your outlet,

consult an electrician for replacement of the

obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from

the apparatus.

11. Only use attachments/accessories specified by

the manufacturer.

12. Use only with the cart,

stand, tripod, bracket, or

table specified by the

manufacturer, or sold

with the apparatus. When

a cart is used, use caution

when moving the

cart/apparatus combination to avoid injury from

tip-over.

13. Unplug this apparatus during lightning storms or

when unused for long periods of time.

14. Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way, such as

power-supply cord or plug is damaged, liquid

has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally, or

has been dropped.

15. Damage Requiring Service

Unplug the apparatus from the wall outlet and

refer servicing to qualified service personnel

under the following conditions:

A. When the power-supply cord or plug is

damaged,

B. If liquid has been spilled, or objects have

fallen into the apparatus,

C. If the apparatus has been exposed to rain or

water,

D. If the apparatus does not operate normally

by following the operating instructions.

Adjust only those controls that are covered

by the operating instructions as an improper

adjustment of other controls may result in

damage and will often require extensive

work by a qualified technician to restore the

apparatus to its normal operation,

E. If the apparatus has been dropped or

damaged in any way, and

F. When the apparatus exhibits a distinct

change in performance this indicates a need

for service.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPARATUS

TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO

USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

AVIS

PORTABLE CART WARNING

S3125A

E52_LS3100_120910.book 2 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

16. Object and Liquid Entry

Never push objects of any kind into the

apparatus through openings as they may touch

dangerous voltage points or short-out parts that

could result in a fire or electric shock.

The apparatus shall not be exposed to dripping

or splashing and no objects filled with liquids,

such as vases shall be placed on the apparatus.

Don’t put candles or other burning objects on

top of this unit.

17. Batteries

Always consider the environmental issues and

follow local regulations when disposing of

batteries.

18. If you install the apparatus in a built-in

installation, such as a bookcase or rack, ensure

that there is adequate ventilation.

Leave 20 cm (8") of free space at the top and

sides and 10 cm (4") at the rear. The rear edge of

the shelf or board above the apparatus shall be

set 10 cm (4") away from the rear panel or wall,

creating a flue-like gap for warm air to escape.

Precautions

1. Recording Copyright—Unless it’s for personal

use only, recording copyrighted material is

illegal without the permission of the copyright

holder.

2. AC Fuse—The AC fuse inside the unit is not

user-serviceable. If you cannot turn on the unit,

contact your Onkyo dealer.

3. Care—Occasionally you should dust the unit all

over with a soft cloth. For stubborn stains, use a

soft cloth dampened with a weak solution of

mild detergent and water. Dry the unit

immediately afterwards with a clean cloth. Don’t

use abrasive cloths, thinners, alcohol, or other

chemical solvents, because they may damage the

finish or remove the panel lettering.

4. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR

THE FIRST TIME, READ THE FOLLOWING

SECTION CAREFULLY.

AC outlet voltages vary from country to country.

Make sure that the voltage in your area meets the

voltage requirements printed on the unit’s rear

panel (e.g., AC 230 V, 50 Hz or AC 120 V, 60

Hz).

The power cord plug is used to disconnect this

unit from the AC power source. Make sure that

the plug is readily operable (easily accessible) at

all times.

For models with [POWER] button, or with both

[POWER] and [ON/STANDBY] buttons:

Pressing the [POWER] button to select OFF

mode does not fully disconnect from the mains.

If you do not intend to use the unit for an

extended period, remove the power cord from

the AC outlet.

For models with [ON/STANDBY] button only:

Pressing the [ON/STANDBY] button to select

Standby mode does not fully disconnect from

the mains. If you do not intend to use the unit for

an extended period, remove the power cord from

the AC outlet.

5. Preventing Hearing Loss

Caution

Excessive sound pressure from earphones and

headphones can cause hearing loss.

6. Batteries and Heat Exposure

Warning

Batteries (battery pack or batteries installed)

shall not be exposed to excessive heat as

sunshine, fire or the like.

E52_LS3100_120910.book 3 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

7. Never Touch this Unit with Wet Hands—

Never handle this unit or its power cord while

your hands are wet or damp. If water or any

other liquid gets inside this unit, have it checked

by your Onkyo dealer.

8. Handling Notes

• If you need to transport this unit, use the

original packaging to pack it how it was when

you originally bought it.

• Do not leave rubber or plastic items on this

unit for a long time, because they may leave

marks on the case.

• This unit’s top and rear panels may get warm

after prolonged use. This is normal.

• If you do not use this unit for a long time, it

may not work properly the next time you turn

it on, so be sure to use it occasionally.

For U.S. models

FCC/IC Information for User

IMPORTANT NOTE:

This equipment complies with FCC/IC radiation

exposure limits set forth for an uncontrolled

environment and meets the FCC radio frequency

(RF) Exposure Guidelines in Supplement C to

OET65 and RSS-102 of the IC radio frequency (RF)

Exposure rules.

This equipment has very low levels of RF energy that

it deemed to comply without maximum permissive

exposure evaluation (MPE). But it is desirable that it

should be installed and operated keeping the radiator

at least 20 cm or more away from person’s body

(excluding extremities: hands, wrists, feet and

ankles).

REMARQUE IMPORTANTE :

Cet équipement est conforme aux limites FCC/IC

d’exposition aux rayonnements définies pour un

environnement non réglementé, aux lignes

directrices de la FCC en matière d’exposition aux

radiofréquences (RF) spécifiées dans le supplément

C du bulletin OET65 et aux régulations RSS-102 de

l’IC sur l’exposition aux radiofréquences (RF).

Cet équipement étant associé à de très faibles

niveaux d’énergie radiofréquence, il est considéré

conforme sans évaluation de l’exposition maximale

admise (EMA). Il est cependant conseillé de

l’installer et de l’utiliser en maintenant la source de

rayonnement radioélectrique à 20 cm minimum du

corps (à l’exclusion des extrémités du corps : les

mains, les poignets, les pieds et les chevilles).

FCC Caution:

FCC WARNING

Changes or modifications not expressly approved by

the party responsible for compliance could void the

user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However,

there is no guarantee that interference will not occur

in a particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to

correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV

technician for help.

This transmitter must not be co-located or operated

in conjunction with any other antenna or transmitter.

Cet émetteur ne doit pas être placé à de ou utilisé

conjointement avec une autre antenne ou un autre

émetteur.

For Canadian Models

NOTE:

THIS CLASS B DIGITAL APPARATUS

COMPLIES WITH CANADIAN ICES-003.

For models having a power cord with a polarized

plug:

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH

WIDE BLADE OF PLUG TO WIDE SLOT,

FULLY INSERT.

E52_LS3100_120910.book 4 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

Modèle pour les Canadien

REMARQUE:

CET APPAREIL NUMÉRIQUE DE LA CLASSE B

EST CONFORME À LA NORME NMB-003 DU

CANADA.

Sur les modèles dont la fiche est polarisée:

ATTENTION:

POUR ÉVITER LES CHOCS ÉLECTRIQUES,

INTRODUIRE LA LAME LA PLUS LARGE DE

LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRISE ET

POUSSER JUSQU’AU FOND.

This device complies with Industry Canada licence-

exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not

cause interference, and (2) this device must accept

any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR

d’Industrie Canada applicables aux appareils radio

exempts de licence. L’exploitation est autorisée aux

deux conditions suivantes : (1) l’appareil ne doit pas

produire de brouillage, et (2) l’utilisateur de

l’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est

susceptible d’en compromettre le fonctionnement.

For British models

Replacement and mounting of an AC plug on the

power supply cord of this unit should be performed

only by qualified service personnel.

IMPORTANT

The wires in the mains lead are coloured in

accordance with the following code:

Blue: Neutral

Brown: Live

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows:

The wire which is coloured blue must be connected

to the terminal which is marked with the letter N or

coloured black.

The wire which is coloured brown must be connected

to the terminal which is marked with the letter L or

coloured red.

IMPORTANT

The plug is fitted with an appropriate fuse. If the fuse

needs to be replaced, the replacement fuse must

approved by ASTA or BSI to BS1362 and have the

same ampere rating as that indicated on the plug.

Check for the ASTA mark or the BSI mark on the

body of the fuse.

If the power cord’s plug is not suitable for your

socket outlets, cut it off and fit a suitable plug. Fit a

suitable fuse in the plug.

For European Models

Hereby, Onkyo Corporation, declares that this

LAP-301 is in compliance with the essential

requirements and other relevant provisions of

Directive 1999/5/EC.

С настоящето, Onkyo Corporation, декларира,

че LAP-301 е в съответствие със

съществените изисквания и

другитеприложими разпоредби на Директива

1999/5/EC.

Onkyo Corporation tímto prohlašuje, že LAP-301

splňuje základní požadavky a všechna příslušná

ustanoveni Směrnice 1999/5/ES.

Undertegnede Onkyo Corporation erklærer

herved, at følgende udstyr LAP-301 overholder

de væsentlige krav og øvrige relevante krav i

direktiv 1999/5/EF.

Hiermit erklärt Onkyo Corporation, dass sich das

Gerät LAP-301 in Übereinstimmung mit den

grundlegenden Anforderungen und den übrigen

einschlägigen Bestimmungen der Richtlinie

1999/5/EG befindet.

Käesolevaga kinnitab Onkyo Corporation seadme

LAP-301 vastavust direktiivi 1999/5/EÜ

põhinõuetele ja nimetatud direktiivist tulenevatele

teistele asjakohastele sätetele.

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Ο ΚΑΤΑΣΚΕΥΑΣΤΗΣ

Onkyo Corporation ∆ΗΛΩΝΕΙ ΟΤΙ LAP-301

ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ

ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ

∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕΚ

Por la presente, Onkyo Corporation, declara que

este LAP-301 cumple con los requisitos

esenciales y otras exigencias relevantes de la

Directiva 1999/5/EC.

Par la présente, Onkyo Corporation déclare que

l’appareil LAP-301 est conforme aux exigences

essentielles et aux autres dispositions

pertinentes de la directive 1999/5/CE.

E52_LS3100_120910.book 5 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

Con la presente Onkyo Corporation dichiara che

questo LAP-301 è conforme ai requisiti

essenziali ed alle altre disposizioni pertinenti

stabilite dalla direttiva 1999/5/CE.

Ar šo Onkyo Corporation deklarē, ka LAP-301

atbilst Direktīvas 1999/5/EK būtiskajām prasībām

un citiem ar to saistītajiem noteikumiem.

Šiuo Onkyo Corporation deklaruoja, kad šis

LAP-301 atitinka esminius reikalavimus ir kitas

1999/5/EB Direktyvos nuostatas.

A Onkyo Corporation ezzennel kijelenti, hogy a

LAP-301 típusú beren-dezés teljesíti az alapvető

követelményeket és más 1999/5/EK irányelvben

meghatározott vonatkozó rendelkezéseket.

Hierbij verklaart Onkyo Corporation dat het

toestel l LAP-301 in overeenstemming is met de

essentiële eisen en de andere relevante bepalin-

gen van richtlijn 1999/5/EG.

Niniejszym Onkyo Corporation deklaruje że

LAP-301 jest zgodny z zasadniczymi

wymaganiami i innymi właściwymi

postanowieniami Dyrektywy 1999/5/EC.

Eu, Onkyo Corporation, declaro que o LAP-301

cumpre os requisitos essenciais e outras

provisões relevantes da Directiva 1999/5/EC.

Prin prezenta, Onkyo Corporation, declară că

aparatul LAP-301 este în conformitate cu

cerinţele esenţiale şi cu alte prevederi pertinente

ale Directivei 1999/5/CE.

Onkyo Corporation týmto vyhlasuje, že LAP-301

a spĺňa základné požiadavky a všetky príslušné

ustanovenia Smernice 1999/5/ES.

Onkyo Corporation izjavlja, da je ta LAP-301 v

skladu z bistvenimi zahtevami in drugimi

relevantnimi določili direktive 1999/5/ES.

Onkyo Corporation vakuuttaa täten että

LAP-301 tyyppinen laite on direktiivin 1999/5/EY

oleellisten vaatimusten ja sitä koskevien

direktiivin muiden ehtojen mukainen.

Härmed förklarar Onkyo Corporation att denna

LAP-301 följer de väsentliga kraven och andra

relevanta stadgar i Direktiv 1999/5/EC.

Hér með lýsir Onkyo Corporation því yfir að

varan LAP-301 er í samræmi við grunnkröfur og

aðrar kröfur sem gerðar eru í tilskipun

1999/5/EC.

Onkyo Corporation erklærer herved at denne

LAP-301 er i overensstemmelse med vesentlige

krav og andre relevante bestemmelser i direktiv

1999/5/EC.

Speaker Precautions

Placement

• The subwoofer cabinet is made out of wood and is

therefore sensitive to extreme temperatures and

humidity, do not put it in locations subject to direct

sunlight or in humid places, such as near an air

conditioner, humidifier, bathroom, or kitchen.

• Do not put water or other liquids close to the

speakers. If liquid is spilled over the speakers, the

drive units may be damaged.

• Speakers should only be placed on sturdy, flat

surfaces that are free from vibration.

Putting them on uneven or unstable surfaces, where

they may fall and cause damage, will affect the

sound quality.

• Subwoofer is designed to be used in the upright

vertical position only. Do not use it in the

horizontal or tilted position.

• If the unit is used near a turntable, CD player or

DVD player, howling or slipping of sound may

occur. To prevent this, move the unit away from

the turntable, CD player or DVD player, otherwise

lower the unit’s output level.

Use with a TV set

In general, Braun tubes used for color television sets,

etc. are extremely sensitive and can be affected even

by the magnetism of the earth. If a speaker system is

used near them, therefore, discoloring or distortion of

pictures will occur.

These speakers are not provided with magnetic

shielding. If discoloration or distortion occurs, move

the speakers apart from the television set.

Input Signal Warning

The speakers can handle the specified input power

when used for normal music reproduction. If any of

the following signals are fed to them, even if the

input power is within the specified rating, excessive

current may flow in the speaker coils, causing

burning or wire breakage:

1. Interstation noise from an untuned FM radio.

2. Sound from fast-forwarding a cassette tape.

3. High-pitched sounds generated by an oscillator,

electronic musical instrument, and so on.

4. Amplifier oscillation.

5. Special test tones from audio test CDs and so on.

6. Thumps and clicks caused by connecting or

disconnecting audio cables (Always turn off

your amplifier before connecting or

disconnecting cables).

7. Microphone feedback.

E52_LS3100_120910.book 6 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

Package Contents

Make sure you have the following items:

*1 (Australian models) The plug type varies from

country to country. From the two supplied power

cords, choose the one whose plug matches the

type of your AC wall outlet.

*In catalogs and on packaging, the letter at the end

of the product name indicates the color.

Specifications and operations are the same

regardless of color.

Features

Sound System Controller

• Powerful Digital Amplifier

•20 W/Ch (4 Ω, 1 kHz, 0.8%, 2 Channels

Driven, FTC)

•20 W/Ch (4 Ω, 1 kHz, 0.8%, 2 Channels

Driven, IEC)

•22 W/Ch (4 Ω, 1 kHz, 0.8%, 2 Channels

Driven, JEITA)

• 2 Digital Inputs (Optical/Coaxial)

• 1 Analog Input (Mini Jack)

• Normal Mode for Wide Spread Surround

• Vocal Mode for Clear Voice (for News

Program)

•

Bluetooth ver.2.1+EDR (Enhanced Data Rate)

• Auto Standby Function

• Auto Power On Function

• Preset Remote Control Codes for Most TV

Brands and Programming Function

Subwoofer

• Wireless Design for Free Setting and

Powerful Sound

• Powered Bass Reflex Design

• 6-1/2 inch (16 cm) Cone

Front Speakers

• Detachable Speaker Stands for Greater

Mounting Flexibility

• 2-1/2 inch (6.5 cm) Full-range Cone × 2

Sound system controller (LAP-301)

Remote controller (RC-858S)

AC adapter and Power cord*1 (➔page 16)

Stereo mini plug cable 5 ft. (1.5 m)

Optical digital audio cable 5 ft. (1.5 m)

Front speakers (SLM-301)

Speaker stand × 2

Speaker cable 10 ft. (3.0 m) × 2

12 thin rubber stoppers (For Front speakers and

Subwoofer)

8 thick rubber stoppers

Wire cable with eye bolt × 2

Wireless subwoofer (SLW-301)

Power cord*1 (➔page 16)

Quick Start Guide

and are trademarks of SRS

Labs, Inc. WOW HD and TruVolume technologies

are incorporated under license from SRS Labs, Inc.

Manufactured under license from Dolby

Laboratories. Dolby and the double-D symbol are

trademarks of Dolby Laboratories.

Onkyo does not guarantee Bluetooth compatibility

between the LAP-301 system and all Bluetooth-

enabled devices.

For compatibility between the LAP-301 system and

another device with Bluetooth technology, consult

the device’s documentation and dealer. In some

countries, there may be restrictions on using

Bluetooth devices. Check with your local

authorities.

The Bluetooth® word mark and logos are registered

trademarks owned by Bluetooth SIG, Inc. and any

use of such marks by Onkyo is under license. Other

trademarks and trade names are those of their

respective owners.

Please read rating label at the bottom or rear panel

of system for other safety information.

E52_LS3100_120910.book 7 ページ２０１２年９月１０日　月曜日　午後４時３８分

TENTATIVE

■Using the Remote Controller

Remove the plastic film before using the

remote controller.

To use the remote controller, point it at the

controller’s remote control sensor, as shown

below.

■Replacing the Battery

Use only a battery of the same type (CR2025).

Note

• If the remote controller doesn’t work reliably, try

replacing the battery.

• If you intend not to use the remote controller for a

long time, remove the battery to prevent damage

from leakage or corrosion.

• Remove expired battery as soon as possible to

prevent damage from leakage or corrosion.

Caution

• Replacing the battery incorrectly may cause an

explosion. Use only a battery of the same type or an

equivalent.

(Placing on the floor, etc.)

LAP-301

Remote control

sensor

Approx.

16ft. (5m)

(Mounting to the wall)

LAP-301

Remote control

sensor

Approx.

16ft. (5m)

LAP-301

Remote control

sensor

Approx.

16ft. (5m)

Positive ⊕ side

Pull out firmly in the direction of the arrow

pressing the tab in the direction of the arrow.

Push

Pull

Back side

E52_LS3100_120910.book 8 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

Getting to Know the LS3100

For detailed information, see the pages in parentheses.

a8ON/STANDBY button (17)

bON/STANDBY LED (17)

cRemote control sensor (8)

dVolume –/+ buttons (17)

e/TV input button (17)

fBluetooth LED (17)

aDC IN jack

bSPEAKER OUT terminals

cAUDIO IN (TV) DIGITAL OPTICAL and

COAXIAL jacks

dAUDIO IN (TV) ANALOG audio jack

Top Panel (LAP-301)

dcfeab

Rear Panel (LAP-301)

ab cd

See “Connections” for connection (➔pages 14 to 16).

E52_LS3100_120910.book 9 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

Caution

• The front grilles are not designed to be removed so

do not attempt to remove them forcibly, as this will

damage them.

Note

• The shape of the AC INLET differs depending on

the country.

For detailed information, see the pages in

parentheses.

a8 (On/Standby) button (17)

b/ INPUT buttons (17)

cVOLUME +/– buttons (17)

dSUBWOOFER +/– buttons (18)

e (Mute) button (18)

fSOUND MODE button (19)

TV remote control commands of several TV

brands are registered in the controller. These

commands enable your TV remote controller to

operate the Volume +/– and Mute function of

the controller.

Tip

• Some types of TV remote controllers are not

compatible with this function. In this case, use the

supplied remote controller or perform the

programming of the controller. See “Programming

the controller for use of existing remote controller”

for more details (➔page 21).

• If you operate the controller with your TV remote

controller, set the Auto Power On function to on.

The controller cannot be turned on by using Power

On button on your TV remote controller.

Front Speakers (SLM-301)

Subwoofer (SLW-301)

Cabinet

Speaker terminals

(Front) (Side)

(Rear)

Hole for eye bolt

Slit for stand

(Front) (Rear)

AC INLET

LINK button

LINK LED

Remote Controller

Using your TV remote

controller

E52_LS3100_120910.book 10 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

Placement

This section explains how to mount/place the

controller, the front speaker and the subwoofer.

aSound System Controller (LAP-301)

bFront speakers (SLM-301)

cSubwoofer (SLW-301)

The controller can be placed on the flat floor,

and also mounted to the wall by using a

commercially available wall-mounting screw.

■Wall mounting

Tip

• The controller can be mounted upside-down.

Caution

• For mounting the controller,

use a screw with a head

diameter of 1/4"(6 mm) or

more and 2/32"(7 mm) or less,

and a shank diameter of

1/8"(3 mm) or more and

5/32"(4 mm) or less. The

screws as thick and long as

possible are recommended.

• Leave a gap of between 3/16" (5 mm) and 1/4"

(6 mm) between the wall and the base of the screw

head, as shown (We recommend that you consult a

home installation professional).

• Mount the controller as close as possible to the TV

set without hiding the remote control sensor for the

TV remote controller.

• Mount the controller in a well-ventilated place.

In this instruction manual, Sound System

Controller (LAP-301) is described as

“controller”.

Mounting the Controller

1Mark the point of the wall by using

WALL MOUNTING TEMPLATE.

Mark the two points by using a pencil so

that the controller can be mounted

horizontally.

2Insert a commercially available wall-

mounting screw into the mark and

screw it.

3Insert the head of the screw into the

keyhole slot on the bottom of the

controller and fix it firmly.

Please confirm that the head of the screw

is at the top of the hole.

bcaKeyhole

slots for

wall

mounting

Bottom

of the

LAP-301

Screw

5-11/16"

(145 mm)

Wall

3/16" to 1/4"

(5 to 6 mm)

E52_LS3100_120910.book 11 ページ２０１２年９月１０日　月曜日　午後５時９分

TENTATIVE

Front speaker can be placed on the table top or

mounted to the wall by using supplied stands.

■Using the rubber stoppers for a more

stable platform

We recommend to use the supplied rubber

stoppers to achieve the best possible sound.

Attach the rubber stoppers to the four corners

of the bottom. The rubber stopper also provides

stability.

(Placing on the floor, etc.)

(Using the stand)

■Attaching the stand

Insert the stand into the stand slit on the rear of

the front speaker.

(Table top)

(Wall Mounting)

Tip

• The front speaker can be mounted/placed both

horizontally and vertically.

■Adjusting the angle

The angle of the speaker can be adjusted in two

ways depending on which stand slit you use.

Mounting/Placing the Front

Speakers

Thick rubber stoppers

Bottom of the SLM-301

Thin rubber stoppers

Bottom of the supplied stand

(Using the upper slit) (Using the lower slit)

Slit for stand

E52_LS3100_120910.book 12 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

■Wall mounting

Note

• For mounting the front

speaker, use a screw with a

head diameter of 2/32"(7 mm)

or more and 5/16"(9 mm) or

less, and a shank diameter of

1/8"(3 mm) or more and

5/32"(4 mm) or less. The

screws as thick and long as

possible are recommended.

• Leave a gap of between 5/32" (4 mm) and 3/16"

(5 mm) between the wall and the base of the screw

head, as shown.

• Mount the front speaker to the vertical wall.

Mounting to the inclined wall might cause a falling

of the speaker by coming off the stand.

■Fixing the front speakers to prevent a

falling accident

When you mount the speaker to the wall, make

sure to set it firmly so that it cannot slip and

fall. This is especially important if you have

small children. Pass the end of the supplied

wire through the hole of the stand and tie it.

Screw the eye bolt into the eye bolt hole on the

back of the cabinet.

Note

• A mounting screw’s ability to support a speaker

depends on the material and the position of studs of

the wall (We recommend that you consult a home

installation professional).

■Using the rubber stoppers for a more

stable platform

We recommend to use the supplied rubber

stoppers to achieve the best possible sound.

Attach the rubber stoppers to the four corners

of the bottom. The rubber stopper also provides

stability.

1Attach the supplied stand referring to

the illustration for wall mounting.

2Screw a commercially available wall-

mounting screw into the wall.

3Insert the head of the screw into the

keyhole slot on the bottom of the

supplied stand and fix it firmly.

Please confirm that the head of the screw

is at the top of the hole.

Screw

Keyhole slot for wall

mounting

Wall

5/32" to 3/16"

(4 to 5 mm)

Placing the Subwoofer

Thin rubber stoppers

Bottom of the SLW-301

E52_LS3100_120910.book 13 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

Connections

Connect the supplied front speaker. Connect

positive (+) terminal of the front speaker to

positive (+) terminal of the controller

(LAP-301) and negative (-) terminal of the

front speaker to negative (-) terminal of the

controller.

Tip

• The two speakers are identical, so it doesn’t matter

which one you use on the left or right.

Speaker Connection Precautions

Read the following before connecting your

speakers:

• You can connect speakers with an impedance

of between 4 and 8 ohms.

• Disconnect the power cord from the wall

outlet before making any connections.

• Pay close attention to speaker wiring polarity.

In other words, connect positive (+) terminals

only to positive (+) terminals, and negative

(-) terminals only to negative (-) terminals. If

you get them the wrong way around, the

sound will be out of phase and will sound

unnatural.

• Be careful not to short the positive and

negative wires. Doing so may damage the

controller.

• Make sure the metal core of the wire does not

have contact with the controller’s rear panel.

Doing so may damage the controller.

• Don’t connect more than one cable to each

speaker terminal. Doing so may damage the

controller.

• Don’t connect one speaker to several

terminals.

Connecting the Front Speakers

Front right

speaker

Supplied speaker cable

Front left

speaker

E52_LS3100_120910.book 14 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

Using the Subwoofer

To find the best position for your subwoofer,

while playing a movie or some music with

good bass, experiment by placing your

subwoofer at various positions within the

room, and choose the one that provides the

most satisfying results.

• Before making any TV connections, read the

manuals supplied with your TV.

• Don’t connect the power cord until you’ve

completed and double-checked the TV

connection.

• Push plugs in all the way to make good

connections (loose connections can cause

noise or malfunctions).

• To prevent interference, keep audio cable

away from power cords and speaker cables.

Cables and Jacks

■Optical digital audio

Optical digital connection allows you to enjoy

digital sound such as PCM or Dolby Digital.

The audio quality is the same as coaxial.

■Coaxial digital audio

Coaxial digital connection allows you to enjoy

digital sound such as PCM or Dolby Digital.

The audio quality is the same as optical.

■1/8" (3.5 mm) Stereo mini plug

This cable carries analog audio.

Note

• The controller’s optical digital jack has a shutter-

type cover that open when an optical plug is inserted

and close when it’s removed. Push the plug in all the

way.

Caution

• To prevent shutter damage, hold the optical

plug straight when inserting and removing.

Connecting to the TV

Connect the TV to either of the jacks of the

controller.

Tip

• If the Dolby Digital signal is input, the

ON/STANDBY LED flashes white and amber

alternately three times.

Note

• Don’t connect the different types of jacks together.

• When you find the both audio output from your TV

and LS3100, turn the audio output from your TV

speaker off by setting on the TV.

About TV Connections

Corner

position

1/3 of wall

position

Stereo

mini plug

cable

(supplied)

Coaxial digital

audio cable

Optical digital

audio cable

(supplied)

E52_LS3100_120910.book 15 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

Note

• Before connecting the power cord, connect all of

your speakers and TV.

• Turning on the unit may cause a momentary power

surge that might interfere with other electrical

equipment on the same circuit. If this is a problem,

plug the unit into a different branch circuit.

• Do not use the power cord other than the one

supplied with the unit. The supplied power cord is

designed exclusively for use with the unit and

should not be used with any other equipment.

• Never disconnect the power cord from the unit

while the other end is still plugged into a wall outlet.

Doing so may cause an electric shock. Always

disconnect the power cord from the wall outlet first,

and then the unit.

Connecting the Power cord

(LAP-301)

1Connect the supplied AC adapter and

the power cord.

2Insert the plug of the AC adapter into

DC IN.

3Plug the AC adapter into an AC wall

outlet.

(SLW-301)

1Connect the supplied power cord for

subwoofer to AC INLET.

Note

• The shape of the AC INLET differs depending

on the country.

2Plug the power cord into an AC wall

outlet.

3To AC wall outlet

To AC wall outlet

E52_LS3100_120910.book 16 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

Operations

Tip

• For details on power management settings, see

“Setting the Auto Power On” (➔page 18).

Note

• To prevent any loud surprises when you turn on the

controller, always turn down the volume before you

turn it off.

■Operating with the remote controller

■Operating on the controller

Tip

• Adjust the volume by 1 step in the 0 to 35 range.

The volume can be set by each of TV selector and

Bluetooth selector.

•The ON/STANDBY LED flashes by receiving the

signal from the remote controller.

• When the Auto Power On function is set to on, the

controller is automatically turned on by receiving

the audio input from the TV and the TV selector is

selected.

Turning On the controller

1Press 8ON/STANDBY on the top panel.

Press 8 on the remote controller.

The controller comes on, and the

ON/STANDBY LED lights white.

Press 8ON/STANDBY or 8 again to set

the controller to standby mode.

VOLUME +/-

SUBWOOFER +/-

SOUND MODE

/ INPUT

8ON/STANDBY

ON/STANDBY LED

Volume –/+

/TV input

Bluetooth LED

Enjoying the sound

1Turn on the connected TV.

2Press INPUT to select the TV

selector.

other content without

annoying volume fluctuations.

Listening to an audio from

Bluetooth device

1Press the /TV input button on the top

panel repeatedly or INPUT on the

remote controller until the Bluetooth

LED lights to select the Bluetooth

selector.

The controller searches the component

connected previous time and starts the

pairing in five seconds when the

corresponding item is not found.

Note

• If you press the /TV input button on the top

panel or INPUT on the remote controller

again during pairing and switch the selector to

TV, the operation will be cancelled.

2While the Bluetooth LED is flashing

(25 seconds), you can operate the

Bluetooth-enabled device to pair with

the controller within a 32 ft. (10 m)

range.

For details on the Bluetooth connection,

refer to the user manual of the Bluetooth-

enabled device.

The controller may not work as normal

depending on the circumstance even

though the controller is placed within the

32 ft. (10 m) range. In such cases, get the

Bluetooth-enabled device closer to the

controller and retry the operation.

3Once the controller is detected and its

name “Onkyo LS3100” appears on the

display of your Bluetooth-enabled

device, select the “Onkyo LS3100.” If a

prompt requests a password (PIN code),

key in the “0000”.

When a Bluetooth connection is

established successfully, the Bluetooth

LED flashes twice.

4Start playback on your device. The

controller automatically starts playing

the audio.

E52_LS3100_120910.book 19 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

Tip

• If you press and hold the /TV input button on the

top panel or INPUT on the remote controller for

three seconds with Bluetooth selector selected, the

Bluetooth connection to the Bluetooth-enabled

device is interrupted and start the pairing.

Note

• If there is no sound output even after the paring is

done successfully, consult the user manual of the

Bluetooth-enabled device, and then select the

“Onkyo LS3100” as the audio output device.

• The controller can store the pairing information of

up to 8 Bluetooth devices. If the pairing is done for

the ninth Bluetooth device, the pairing information

of device connected via Bluetooth in the most past

times is erased.

• For some Bluetooth-enabled devices, a pairing is

necessary for every reconnection.

• The multiple Bluetooth devices cannot be

connected at the same time.

E52_LS3100_120910.book 20 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

Useful Function

Programming the controller for use of

existing remote controller

The controller can be operated with your existing TV remote controller or any other remote

controller by programming the controller. This section explains how to program the controller to

operate ON/STANDBY function on the controller by pressing the 5 (number button) on your TV

remote controller as an example.

This operation can be done only from the top panel.

The following button operation can be set.

On/Standby

Volume –/+

Mute

Bluetooth

Sound Mode

Here is an example of operating the

8ON/STANDBY button function of the

controller by pressing the 5 (number button) on

your TV remote controller.

■Button operation

Note

• Operating one button operation on the controller by

several other remote controllers is not possible.

• If you use the remote controller programming

function, TV remote controller preprogrammed

code registered in the controller cannot be used

(➔page 10). If you operate the controller with

your TV remote controller by using TV remote

controller preprogrammed code, the controller

should be initialized (➔page 22).

Settable button operation

Setting the button operation

1Simultaneously press and hold the

/TV input button and

8ON/STANDBY for three seconds.

The mode is switched to the remote

controller programming mode and

ON/STANDBY LED flashes amber.

2Aim your TV remote controller to the

remote control sensor of the controller

and press 5 (number button) on your TV

remote controller three times within

10 seconds.

The ON/STANDBY LED flashes amber

twice indicating that the registration is

completed.

Tip

•If the ON/STANDBY LED does not flash by

pressing the buttons on your TV remote

controller, your TV remote controller might be

the type that the controller cannot read. In this

case, use the supplied remote controller.

Operating

function

Button operation on the

controller

8ON/STANDBY + 8ON/STANDBY

Volume + + Volume +

Volume – + Volume –

Mute + Volume + + Volume –

/TV input + 8ON/STANDBY +

Volume +

Sound Mode + 8ON/STANDBY +

Volume –

E52_LS3100_120910.book 21 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

Appendix

Troubleshooting

If you have any trouble using the controller,

look for a solution in this section. If you can’t

resolve the issue yourself, contact your Onkyo

dealer.

■Can’t turn on the controller

■The controller turns off unexpectedly

■The controller turns off and after

restoring the power, it turns off again

If you can’t resolve the issue yourself, try

resetting the controller before contacting

your Onkyo dealer.

To reset the controller to its factory

defaults, simultaneously press and hold

8ON/STANDBY and Volume –/+ buttons

for 10 seconds. The controller will enter

the standby mode after completing the

initialization.

Note that resetting the controller will delete

your custom settings.

Power

Make sure that the power cord is

properly plugged into the wall outlet.

—

Unplug the power cord from the wall

outlet, wait 10 seconds or more, then

plug it in again.

—

The controller will automatically enter

standby mode when Auto Standby

launches.

The protection circuit has been

activated. Remove the power cord from

the wall outlet immediately. Make sure

that all speaker cables and input sources

are properly connected, and leave the

controller with its power cord

disconnected for 1 hour. After that,

reconnect the power cord and turn the

power on. If the controller turns off

again, unplug the power cord and

contact your Onkyo dealer.

WARNING

If smoke, smell or abnormal noise is produced

by the controller, unplug the power cord from

the wall outlet immediately and contact your

Onkyo dealer.

E52_LS3100_120910.book 22 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

■There’s no sound, or it’s very quiet

■The subwoofer produces no sound

■Noise can be heard

■The remote controller doesn’t work

■The controller and the TV operated by

your TV remote controller doesn’t

work

■Standby power consumption

■Pairing the controller and the

subwoofer

Audio

Make sure that all audio connecting

plugs are pushed in all the way.

Make sure that the input of TV is

connected properly.

Make sure that the polarity of the

speaker cables is correct, and that the

bare wires are in contact with the metal

part of each speaker terminal.

Make sure that the speaker cables are

not shorting.

When the ON/STANDBY LED flashes

white, the muting is enabled. Press

on the remote controller or the

Volume –/+ buttons simultaneously on

the controller to disable the muting.

Make sure that none of the connecting

cables are bent, twisted, or damaged.

—

Make sure that there is no obstacle or

reflection between the controller and the

subwoofer.

—

Make sure that the pairing the controller

and the subwoofer completes normally.

—

Using cable ties to bundle audio cables

with power cords, speaker cables, and

the like may degrade the audio

performance, so refrain from doing it.

—

An audio cable may be picking up

interference. Try repositioning your

cables.

—

Remote Controller

Make sure that the battery is installed

with the correct polarity.

Make sure that the remote controller is

not too far away from the controller, and

that there’s no obstruction between the

remote controller and the controller’s

remote control sensor.

Make sure that the controller is not

subjected to direct sunshine or inverter-

type fluorescent lights. Relocate if

necessary.

—

If the controller is installed in a rack or

cabinet with colored-glass doors, the

remote controller may not work reliably

when the doors are closed.

—

Make sure that the controller mounted

to the wall and the TV set are not placed

too far.

Your TV remote controller might not be

compatible with TV remote controller

preprogrammed codes function. If the

ON/STANDBY LED does not flash by

pressing the buttons on your TV remote

controller, use the supplied remote

controller or program the controller. If

the controller cannot be operated with

your remote controller even if the

programming has been performed, the

controller might not recognize your

remote controller. In this case, use the

supplied remote controller.

—

Others

When the Auto Power On function is set

to “on”, the power consumption in ready

mode may reach up to a maximum of

4W.

—

Turn on the controller before performing

a pairing.

1Press and hold LINK on the rear panel of

the subwoofer for five seconds.

Flashing speed of the LINK LED is

changed.

2Press and hold 8ON/STANDBY on the

controller for three seconds until the

ON/STANDBY LED flashes white.

The controller and the subwoofer starts

pairing. The ON/STANDBY LED flashes

white twice indicating that the pairing is

completed.

E52_LS3100_120910.book 23 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

Tip

• If the controller is turned off or enters the standby

mode, also the subwoofer enters the standby mode

in 30 seconds. In this mode, the controller

automatically detects a pairing point and

reconnects. The subwoofer is automatically turned

on when the link is recovered.

Note

• Depending on the reception condition, the sound

might be stopped or interrupted while using. This is

not a malfunction. In this case, change the place or

direction of the controller or the subwoofer.

• If the controller and the subwoofer are too far, the

reception might be unstable. They should be placed

within 32 ft. (10 m).

• If there is an obstacle (metal door, concrete wall and

insulation contained aluminum foil, etc.) between

the controller and the subwoofer, it might block the

reception and stop the sound. Place the controller

and the subwoofer in good visibility with each

other.

The controller contains a microcomputer for

signal processing and control functions. In

very rare situations, severe interference,

noise from an external source, or static

electricity may cause it to lockup. In the

unlikely event that this happens, unplug the

power cord from the wall outlet, wait at least

five seconds, and then plug it back in.

Onkyo is not responsible for damages (such

as CD rental fees) due to unsuccessful

recordings caused by the unit’s malfunction.

Before you record important data, make sure

that the material will be recorded correctly.

Before disconnecting the power cord from

the wall outlet, set the controller to standby.

E52_LS3100_120910.book 24 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

Specifications

■Audio Inputs

■Audio Output

■Others

Specifications and features are subject to

change without notice.

Controller (LAP-301)

Rated Output Power

All channels: (North American)

20 watts minimum continuous

power per channel, 4 ohm loads,

2 channels driven at 1 kHz, with a

maximum total harmonic

distortion of 0.8% (FTC)

(Others)

2 ch × 20 W at 4 ohms, 1 kHz,

2 ch driven of 0.8% (IEC)

Maximum Effective Output Power

(Australian)

2 ch × 22 W at 4 ohms, 1 kHz,

2 ch driven (JEITA)

THD+N (Total Harmonic Distortion+Noise)

0.8% (Power Rated)

0.2% (1 kHz, 1 W)

Damping Factor 20 (Front, 1 kHz, 8 Ω)

Input Sensitivity and Impedance (Unbalance)

200 mV/47 kΩ (LINE)

Frequency Response

50 Hz - 20 kHz/+3 dB, –3 dB

(DIGITAL)

Signal to Noise Ratio

93 dB (DIGITAL, IHF-A)

Speaker Impedance

4Ω - 8 Ω

Power Supply (North American)

AC 120 V, 60 Hz

(European) AC 230 V, 50 Hz

(Others) AC 220 - 240 V, 50/60 Hz

Power Consumption

*Listed on a label on the bottom

17.8 W

No-sound Power Consumption

(North American and European)

(Others) 6.1 W

Stand-by Power Consumption

(North American) 0.38 W

(European) 0.46 W

(Others) 0.47 W

Dimensions (W × H × D)

187 mm × 32 mm × 120 mm

7-3/8" × 1-1/4" × 4-3/4"

Weight 0.3 kg (0.7 lbs.)

Digital Optical: 1 Coaxial: 1

Analog Stereo Input

ø 3.5 mm mini

Speaker Output SPEAKER OUT

Wireless Subwoofer

Front Speaker (SLM-301)

Type Full Range Closed Box

Impedance 4Ω

Maximum input power

20 W

Output sound pressure level

86 dB/W/m

Frequency Response

200 Hz - 20 kHz

Cabinet capacity 0.6 L (0.021 cubic feet)

Dimensions (W × H × D)

169 mm × 78 mm × 108 mm

6-5/8" × 4-3/8" × 5-1/4"

(incl. grille and projection)

Weight 0.7 kg (1.5 lbs)

Drivers unit 6.5 cm (2-1/2") cone

Terminal Spring type

Other Non magnetic shielding

Subwoofer (SLW-301)

Maximum Effective Output Power

50 W (4 Ω, JEITA)

Play Frequency Band

40 Hz - 200 Hz (DIRECT)

Cabinet capacity 11.5 L (0.41 cubic feet)

Dimensions (W × H × D)

261 mm × 337 mm × 269 mm

10-1/4" × 13-1/4" × 10-9/16"

(incl. grille and projection)

Weight 5.8 kg (12.8 lbs)

Drivers unit 16 cm (6-1/2") cone

Power Supply (North American) AC 120 V, 60 Hz

(Others) AC 220 - 240 V, 50 Hz

Power Consumption

14.8 W

Other Non magnetic shielding

Auto standby

E52_LS3100_120910.book 25 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

Memo

E52_LS3100_120910.book 26 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

Memo

E52_LS3100_120910.book 27 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

SN 29401317

Y1209-1

*29401317*

2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN

Tel: 072-831-8023 Fax: 072-831-8163

http://www.onkyo.com/

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.

Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650

http://www.us.onkyo.com/

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY

Tel: +49-8142-4401-0 Fax: +49-8142-4208-213

http://www.eu.onkyo.com/

The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK

Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700

Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.

Tel: 852-2429-3118 Fax: 852-2428-9039

http://www.onkyochina.com/

1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai,

China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396

http://www.cn.onkyo.com/

E52_LS3100_120910.book 28 ページ２０１２年９月１０日　月曜日　午後４時３０分

TENTATIVE

Onkyo Home Entertainment LS3100 BT Module User Manual Users manual

Onkyo Corporation BT Module Users manual

Contents

Users manual

Navigation menu

Namespaces

Views

Navigation