Onkyo Tx Nr626 Owner S Manual

TX-NR626 to the manual 15712385-f5a8-45dd-86eb-9540272f5688

2014-07-06

: Onkyo Onkyo-Tx-Nr626-Owner-S-Manual onkyo-tx-nr626-owner-s-manual onkyo pdf

Open the PDF directly: View PDF .
Page Count: 140

Download
Open PDF In Browser	View PDF

Contents
AV RECEIVER

TX-NR626

Safety Information and Introduction ............2

Table of Contents ...........................................6

Connections .................................................12

Turning On & Basic Operations..................21

Instruction Manual

Playback........................................................29

Advanced Operations ..................................48

Controlling Other Components...................71

Appendix .......................................................77

Internet Radio Guide
Remote Control Codes

Safety Information and Introduction

WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN
OR MOISTURE.

CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

WARNING

AVIS

RISK OF ELECTRIC SHOCK
DO NOT OPEN

RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR

The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.

Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.

9. Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11. Only use attachments/accessories specified by
the manufacturer.
12. Use only with the cart,
PORTABLE CART WARNING
stand, tripod, bracket, or
table specified by the
manufacturer, or sold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus
S3125A
combination to avoid injury
from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
15. Damage Requiring Service
Unplug the apparatus from the wall outlet and
refer servicing to qualified service personnel
under the following conditions:
A. When the power-supply cord or plug is
damaged,

En-2

B. If liquid has been spilled, or objects have fallen
into the apparatus,
C. If the apparatus has been exposed to rain or
water,
D. If the apparatus does not operate normally by
following the operating instructions. Adjust
only those controls that are covered by the
operating instructions as an improper
adjustment of other controls may result in
damage and will often require extensive work
by a qualified technician to restore the
apparatus to its normal operation,
E. If the apparatus has been dropped or
damaged in any way, and
F. When the apparatus exhibits a distinct change
in performance this indicates a need for
service.
16. Object and Liquid Entry
Never push objects of any kind into the apparatus
through openings as they may touch dangerous
voltage points or short-out parts that could result
in a fire or electric shock.
The apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such
as vases shall be placed on the apparatus.
Don’t put candles or other burning objects on top
of this unit.
17. Batteries
Always consider the environmental issues and
follow local regulations when disposing of
batteries.
18. If you install the apparatus in a built-in installation,
such as a bookcase or rack, ensure that there is
adequate ventilation.
Leave 20 cm (8") of free space at the top and
sides and 10 cm (4") at the rear. The rear edge of
the shelf or board above the apparatus shall be
set 10 cm (4") away from the rear panel or wall,
creating a flue-like gap for warm air to escape.

Safety Information and Introduction

Precautions
1. Recording Copyright—Unless it’s for personal
use only, recording copyrighted material is illegal
without the permission of the copyright holder.
2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
3. Care—Occasionally you should dust the unit all
over with a soft cloth. For stubborn stains, use a
soft cloth dampened with a weak solution of mild
detergent and water. Dry the unit immediately
afterwards with a clean cloth. Don’t use abrasive
cloths, thinners, alcohol, or other chemical
solvents, because they may damage the finish or
remove the panel lettering.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SECTION
CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear
panel (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this
unit from the AC power source. Make sure that
the plug is readily operable (easily accessible) at
all times.
For models with [POWER] button, or with both
[POWER] and [ON/STANDBY] buttons:
Pressing the [POWER] button to select OFF
mode does not fully disconnect from the mains. If
you do not intend to use the unit for an extended
period, remove the power cord from the AC outlet.
For models with [ON/STANDBY] button only:
Pressing the [ON/STANDBY] button to select
Standby mode does not fully disconnect from the
mains. If you do not intend to use the unit for an

extended period, remove the power cord from the
AC outlet.
Preventing Hearing Loss
Caution
Excessive sound pressure from earphones and
headphones can cause hearing loss.
Batteries and Heat Exposure
Warning
Batteries (battery pack or batteries installed) shall
not be exposed to excessive heat as sunshine,
fire or the like.
Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by your Onkyo
dealer.
Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you
originally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks
on the case.
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.

For U.S. and Canadian models
FCC CAUTION
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
Note:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful

En-3

interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment
and receiver.
–Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
–Consult the dealer or an experienced radio/TV
technician for help.
This device complies with Industry Canada licenceexempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not
cause interference, and (2) this device must accept
any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil
doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en
compromettre le fonctionnement.
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.

Safety Information and Introduction

RF Exposure Compliance

Modèle pour les Canadien

IMPORTANT

This equipment complies with FCC/IC radiation
exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency
(RF) Exposure Guidelines in Supplement C to OET65
and RSS-102 of the IC radio frequency (RF)
Exposure rules. This equipment has very low levels of
RF energy that it deemed to comply without
maximum permissive exposure evaluation (MPE).
But it is desirable that it should be installed and
operated keeping the radiator at least 20 cm or more
away from person’s body (excluding extremities:
hands, wrists, feet and ankles).
Cet équipement est conforme aux limites d’exposition
aux rayonnements énoncées pour un environnement
non contrôlé et respecte les régles les
radioélectriques (RF) de la FCC lignes directrices
d’exposition dans le Supplément C à OET65 et
d’exposition aux fréquences radioélectriques (RF)
CNR-102 de l’IC. Cet équipement émet une énergie
RF trés faible qui est considérée conforme sans
évaluation de l’exposition maximale autorisée.
Cependant, cet équipement doit être installé et utilisé
en gardant une distance de 20 cm ou plus entre le
dispositif rayonnant et le corps (à l’exception des
extrémités : mains, poignets, pieds et chevilles).

REMARQUE: CET APPAREIL NUMÉRIQUE DE
LA CLASSE B EST CONFORME À LA NORME
NMB-003 DU CANADA.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS
ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.

The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must
approved by ASTA or BSI to BS1362 and have the
same ampere rating as that indicated on the plug.
Check for the ASTA mark or the BSI mark on the
body of the fuse.
If the power cord’s plug is not suitable for your socket
outlets, cut it off and fit a suitable plug. Fit a suitable
fuse in the plug.

For British models

For European Models

Replacement and mounting of an AC plug on the
power supply cord of this unit should be performed
only by qualified service personnel.

Declaration of Conformity
We declare, under our sole
responsibility, that this product
complies with the standards:
–Safety
–Limits and methods of
measurement of radio disturbance characteristics
–Limits for harmonic current emissions
–Limitation of voltage changes, voltage fluctuations
and flicker
–RoHS Directive, 2011/65/EU
–Hereby, Onkyo Corporation, declares that this
TX-NR626 is in compliance with the essential
requirements and other relevant provisions of
Directive 1999/5/EC.

For Canadian Models
NOTE: THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003.
For models having a power cord with a polarized
plug:
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.

IMPORTANT
The wires in the mains lead are coloured in
accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected
to the terminal which is marked with the letter L or
coloured red.

–С настоящето, Onkyo Corporation, декларира, че
TX-NR626 е в съответствие със съществените
изисквания и другитеприложими разпоредби на
Директива 1999/5/EC.
–Onkyo Corporation tímto prohlašuje, že TX-NR626
splňuje základní požadavky a všechna příslušná
ustanoveni Směrnice 1999/5/ES.
–Undertegnede Onkyo Corporation erklærer herved,
at følgende udstyr TX-NR626 overholder de
væsentlige krav og øvrige relevante krav i direktiv
1999/5/EF.

En-4

Safety Information and Introduction
–Hiermit erklärt Onkyo Corporation, dass sich das
Gerät TX-NR626 in Übereinstimmung mit den
grundlegenden Anforderungen und den übrigen
einschlägigen Bestimmungen der Richtlinie
1999/5/EG befindet.
–Käesolevaga kinnitab Onkyo Corporation seadme
TX-NR626 vastavust direktiivi 1999/5/EÜ
põhinõuetele ja nimetatud direktiivist tulenevatele
teistele asjakohastele sätetele.
–ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Ο ΚΑΤΑΣΚΕΥΑΣΤΗΣ Onkyo
Corporation ∆ΗΛΩΝΕΙ ΟΤΙ TX-NR626
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ
ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ
∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕΚ
–Por la presente, Onkyo Corporation, declara que
este TX-NR626 cumple con los requisitos
esenciales y otras exigencias relevantes de la
Directiva 1999/5/EC.
–Par la présente, Onkyo Corporation déclare que
l’appareil TX-NR626 est conforme aux exigences
essentielles et aux autres dispositions pertinentes
de la directive 1999/5/CE.
–Con la presente Onkyo Corporation dichiara che
questo TX-NR626 è conforme ai requisiti essenziali
ed alle altre disposizioni pertinenti stabilite dalla
direttiva 1999/5/CE.
–Ar šo Onkyo Corporation deklarē, ka TX-NR626
atbilst Direktīvas 1999/5/EK būtiskajām prasībām
un citiem ar to saistītajiem noteikumiem.
–Šiuo Onkyo Corporation deklaruoja, kad šis
TX-NR626 atitinka esminius reikalavimus ir kitas
1999/5/EB Direktyvos nuostatas.
–A Onkyo Corporation ezzennel kijelenti, hogy a
TX-NR626 típusú beren-dezés teljesíti az alapvető
követelményeket és más 1999/5/EK irányelvben
meghatározott vonatkozó rendelkezéseket.

essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.

Complies with
IDA Standards
DA106032

–Niniejszym Onkyo Corporation deklaruje że
TX-NR626 jest zgodny z zasadniczymi
wymaganiami i innymi właściwymi
postanowieniami Dyrektywy 1999/5/EC.

–Onkyo Corporation týmto vyhlasuje, že TX-NR626
a spĺňa základné požiadavky a všetky príslušné
ustanovenia Smernice 1999/5/ES.
–Onkyo Corporation izjavlja, da je ta TX-NR626 v
skladu z bistvenimi zahtevami in drugimi
relevantnimi določili direktive 1999/5/ES.
–Onkyo Corporation vakuuttaa täten että TX-NR626
tyyppinen laite on direktiivin 1999/5/EY oleellisten
vaatimusten ja sitä koskevien direktiivin muiden
ehtojen mukainen.
–Härmed förklarar Onkyo Corporation att denna
TX-NR626 följer de väsentliga kraven och andra
relevanta stadgar i Direktiv 1999/5/EC.
–Hér með lýsir Onkyo Corporation því yfir að varan
TX-NR626 er í samræmi við grunnkröfur og aðrar
kröfur sem gerðar eru í tilskipun 1999/5/EC.
–Onkyo Corporation erklærer herved at denne
TX-NR626 er i overensstemmelse med vesentlige
krav og andre relevante bestemmelser i direktiv
1999/5/EC.

–Hierbij verklaart Onkyo Corporation dat het toestel
l TX-NR626 in overeenstemming is met de

En-5

TA-20120424004

TRA
REGISTERED

DEALER

ER0086260/12

–Eu, Onkyo Corporation, declaro que o TX-NR626
cumpre os requisitos essenciais e outras provisões
relevantes da Directiva 1999/5/EC.
–Prin prezenta, Onkyo Corporation, declară că
aparatul TX-NR626 este în conformitate cu
cerinţele esenţiale şi cu alte prevederi pertinente
ale Directivei 1999/5/CE.

23764/SDPPI/2012
2371

527090

Thank you for purchasing an Onkyo AV
Receiver. Please read this manual thoroughly
before making connections and plugging in the
unit.
Following the instructions in this manual will
enable you to obtain optimum performance and
listening enjoyment from your new AV Receiver.
Please retain this manual for future reference.

Supplied Accessories
Make sure you have the following accessories:
Indoor FM antenna (➔ page 19)
AM loop antenna (➔ page 19)
Power cord (Taiwanese models) (➔ page 21)
Speaker cable labels (➔ page 12)
Speaker setup microphone (➔ page 25)
Remote controller (RC-866M) and two batteries (AA/R6)
Quick Start Guide
*

In catalogs and on packaging, the letter at the end of the
product name indicates the color. Specifications and
operations are the same regardless of color.

Safety Information and Introduction

Table of Contents
Safety Information and Introduction
Important Safety Instructions ......................................2
Precautions ...................................................................3
Supplied Accessories...................................................5
Table of Contents..........................................................6
Features .........................................................................7
Front & Rear Panels......................................................8
Front Panel..................................................................8
Display ........................................................................9
Rear Panel ................................................................10
Remote Controller.......................................................11
Controlling the AV Receiver ......................................11

Connections
Connecting the AV Receiver......................................12
Connecting Your Speakers .......................................12
Connecting the TV/AV components ..........................15
About RIHD-compatible components........................16
Operations that can be performed
with RIHD connection .............................................17
Confirm the settings ..................................................17
Connection Tips ........................................................17
Connecting the Antennas..........................................19
Connecting Onkyo RI Components...........................20
Using Headphones....................................................20

Turning On & Basic Operations

Initial Setup ................................................................. 22
Selecting the Language
for the On-screen Setup Menus ............................. 22
Audyssey MultEQ: Auto Setup ................................. 22
Source Connection ................................................... 23
Remote Mode Setup................................................. 23
Network Connection ................................................. 23
Terminating the Initial Setup ..................................... 23
Using the Automatic Speaker Setup......................... 24
Performing Wireless LAN Setup ............................... 27

Playback
Playback ...................................................................... 29
Controlling Contents of USB or Network Devices..... 30
Understanding Icons on the Display ......................... 31
Playing an Audio from Bluetooth-enabled Device .... 31
Playing a USB Device............................................... 32
Listening to TuneIn ................................................... 32
Registering Other Internet Radio .............................. 34
Changing the Icon Layout
on the Network Service Screen.............................. 34
Playing Music Files on a Server (DLNA) .................. 34
Playing Music Files on a Shared Folder ................... 36
Remote Playback...................................................... 37
Listening to AM/FM Radio ........................................ 38
Playing Audio and Video from Separate Sources..... 40
Using the Listening Modes ....................................... 41
Displaying Source Information.................................. 45
Using the Sleep Timer .............................................. 45
Setting the Display Brightness.................................. 46
Changing the Input Display....................................... 46
Muting the AV Receiver ............................................ 46
Using the Home Menu .............................................. 47

Turning On/Off the AV Receiver ................................21
Connecting the Power Cord ......................................21
Turning On ................................................................21
Turning Off ................................................................21
Firmware Update Notification....................................22
About the HYBRID STANDBY indicator....................22

Advanced Operations
On-screen Setup......................................................... 48
Using the Quick Setup.............................................. 48
Using the Audio Settings of Quick Setup.................. 49
Using the Setup Menu (HOME)................................ 52
Setup Menu Items .................................................... 52
1. Input/Output Assign .............................................. 53
2. Speaker Setup...................................................... 55
3. Audio Adjust ......................................................... 57
4. Source Setup........................................................ 58
5. Listening Mode Preset.......................................... 63
6. Miscellaneous....................................................... 63
7. Hardware Setup.................................................... 64
8. Remote Controller Setup ...................................... 68
9. Lock Setup............................................................ 68
Zone 2.......................................................................... 69
Making Zone 2 Connections..................................... 69
Controlling Zone 2 Components............................... 70

Controlling Other Components
Controlling Other Components................................. 71
Preprogrammed Remote Control Codes .................. 71
Looking up for Remote Control Codes ..................... 71
Entering Remote Control Codes............................... 71
Remapping Colored Buttons .................................... 72
Remote Control Codes for Onkyo Components
Connected via RI ................................................... 72
Resetting the REMOTE MODE Buttons ................... 72
Resetting the Remote Controller .............................. 72
Controlling Other Components ................................. 73
Using the Onkyo Dock.............................................. 75
Controlling Your iPod/iPhone ................................... 76

Appendix
Troubleshooting ......................................................... 77
Firmware Update ........................................................ 85
About HDMI................................................................. 88
Network/USB Features............................................... 89
License and Trademark Information ........................ 91
Specifications ............................................................. 92

To reset the AV receiver, see page 77.

En-6

Safety Information and Introduction

Features

Connections

Amplifier

• 6 HDMI Inputs and 2 Outputs
• 4K (up-scaling and Passthrough*)-compatible HDMI
Inputs

• 95 Watts/Channel @ 8 ohms (FTC)
• 160 Watts/Channel @ 6 ohms (IEC)
• 175 Watts/Channel @ 6 ohms (JEITA)
• WRAT–Wide Range Amplifier Technology
(5 Hz to 100 kHz bandwidth)
• Optimum Gain Volume Circuitry
• H.C.P.S. (High Current Power Supply) Massive
High Power Transformer

Processing
• Incorporates Qdeo™ technology for HDMI Video
Upscaling (to 4K Compatible)
• HDMI (Audio Return Channel, 3D, DeepColor,
x.v.Color, Lip Sync, 4K (up-scaling and
Passthrough), DTS-HD Master Audio, DTS-HD High
Resolution Audio, Dolby TrueHD, Dolby Digital Plus,
DSD and Multi-CH PCM)
• Dolby TrueHD and DTS-HD Master Audio
• Dolby Pro Logic IIz
• Non-Scaling Configuration
• A-Form Listening Mode Memory
• Direct Mode
• Pure Audio Mode (European, Australian and Asian
models)
• Music Optimizer for Compressed Digital Music files
• Phase Matching Bass System
• 192 kHz/24-bit D/A Converters
• Powerful and Highly Accurate 32-bit Processing
DSP
• Jitter Cleaning Circuit Technology

* Compatible with HDMI IN 1 to HDMI IN 4 only

• Onkyo p for System Control
• 3 Digital Inputs (1 Optical/2 Coaxial)
• Component Video Switching (1 Input/1 Output)
• Banana Plug-Compatible Speaker Posts
*

In Europe, using banana plugs to connect speakers to an
audio amplifier is prohibited.

• Powered Zone 2
• Bi-Amping Capability for FL/FR with SBL/SBR
• Internet Radio Connectivity
• Network Capability for Streaming Audio Files
• Wi-Fi (Wireless LAN) Connectivity
• Wireless Music Playback via Bluetooth
• Front-Panel USB Input for Memory Devices
• MHL-Enabled HDMI IN 1

Miscellaneous
• 40 FM/AM Presets
• Audyssey MultEQ® to correct room acoustic
problems
• Audyssey Dynamic EQ® for loudness correction
• Audyssey Dynamic Volume® to maintain optimal
listening level and dynamic range
• Crossover Adjustment
(40/50/60/70/80/90/100/120/150/200 Hz)
• A/V Sync Control Function (up to 800 ms)
• Auto Standby Function
• On-Screen Display via HDMI
• Preprogrammed u-Compatible Remote

En-7

Safety Information and Introduction

Front & Rear Panels
Front Panel
(North American and Taiwanese models)

p q

bc d e

(European, Australian and Asian models)

h i jk l m n

u vw

For detailed information, see the pages in
parentheses.

i MEMORY button (38)
j TUNING MODE button (38)

u USB port (32)

a 8ON/STANDBY button (21)

k DISPLAY button (45)

v SETUP MIC jack (25)

b MUSIC OPTIMIZER button (North American
and Taiwanese models) (50)

l HOME button (47)

w HYBRID STANDBY indicator (22)

c ZONE 2, OFF buttons (70)

m TUNING q/w (38), PRESET e/r (38), cursor
and ENTER buttons

x RT/PTY/TP button (European, Australian and
Asian models) (39)

d Wi-Fi indicator (27)

n RETURN button

e Remote control sensor (11)

o MASTER VOLUME control (29)

y PURE AUDIO button and indicator (European,
Australian and Asian models) (41)

f Display (9)

p BLUETOOTH button and indicator (31, 68)

g LISTENING MODE buttons (41)

q PHONES jack (20)

h DIMMER button (North American and
Taiwanese models) (46)

r TONE and Tone Level buttons (49)
s Input selector buttons (29)

En-8

t AUX INPUT AUDIO/VIDEO jacks

Safety Information and Introduction

Display
s

ab cd

f g

jklm j d
For detailed information, see the pages in
parentheses.

c Headphone indicator (20)

h Tuning indicators
RDS indicator (excluding North American and
Taiwanese models) (39)
AUTO indicator (38)
TUNED indicator (38)
FM STEREO indicator (38)

d 1, 3 and cursor indicators (32)

i MUTING indicator (46)

e Listening mode and format indicators (41, 62)

j Input indicators (18)
HDMI indicator (65)
DIGITAL indicator

a Z2 (Zone 2) indicator (70)
b 3D indicator
This lights when a 3D input signal is detected.

f Audyssey indicator (24, 58)
Dynamic EQ indicator (59)
Dynamic Vol indicator (59)

k ARC (Audio Return Channel) indicator (66)

g M.Opt (Music Optimizer) indicator (50)

l USB indicator (32)

En-9

o p q
m NET indicator (32 to 36, 67)
n Message area
o SLEEP indicator (45)
p Channel/Unit indicators
ch indicator
Hz indicator
m/ft indicator
dB indicator
q ASb (Auto Standby) indicator (66)

Safety Information and Introduction

Rear Panel
(North American, European, Australian and Asian models)

b c

(Taiwanese models)

See “Connecting Your Speakers” for connection
(➔ pages 12 to 20).

g Power cord (North American, European,
Australian and Asian models)

a u REMOTE CONTROL jack

h DIGITAL IN COAXIAL and OPTICAL jacks

b COMPONENT VIDEO IN and OUT jacks

i GND screw

c ETHERNET port

j Composite video and analog audio jacks
(BD/DVD IN, CBL/SAT IN, GAME IN, PC IN,
TV/CD IN, PHONO IN)

d FM ANTENNA jack and AM ANTENNA terminal
e HDMI IN and HDMI output (HDMI OUT MAIN and
HDMI OUT SUB) jacks
f SPEAKERS terminals
(CENTER, FRONT, SURROUND, SURROUND
BACK or FRONT HIGH, ZONE 2)

k MONITOR OUT V jack
l ZONE 2 LINE OUT jacks
m SUBWOOFER PRE OUT jacks
n AC INLET (Taiwanese models)

En-10

Safety Information and Introduction

Remote Controller

For detailed information, see the pages in
parentheses.
a 8 RECEIVER button (21)

Controlling the AV Receiver
To control the AV receiver, press RECEIVER to
select Receiver mode.

c q/w/e/r and ENTER buttons

■ Aiming the remote controller
To use the remote controller, point it at the AV
receiver’s remote control sensor, as shown below.

e Listening Mode buttons (41)

a *2
b

f DIMMER button (46)

g *2
hc
i
d

i VOL q/w button (29)
j RETURN button
k HOME button (47)
Tip

■ Controlling the tuner
To control the AV receiver’s tuner, press TUNER (or
RECEIVER).
You can select AM or FM by pressing TUNER
repeatedly.
a q/w buttons (38)

Approx. 16 ft. (5 m)

l SLEEP button (45)

AV receiver

h DISPLAY button (45)

• You can also use the remote controller to control Onkyo
Blu-ray Disc/DVD player, CD player, and other
components.
See “Entering Remote Control Codes” for more details
(➔ page 71).

Remote control sensor

g MUTING button (46)

To control a component, you must first enter the remote
control code.
See “Entering Remote Control Codes” for more details
(➔ page 71).
These buttons can also be used when a REMOTE
MODE other than Receiver mode is selected.

b REMOTE MODE/INPUT SELECTOR buttons
(29)
d Q SETUP button (48)

RECEIVER

b D.TUN button (38)
c DISPLAY button
d CH +/– button (39)
e Number buttons (38)

En-11

■ Installing the batteries

Batteries (AA/R6)
Note
• If the remote controller doesn’t work reliably, try replacing
the batteries.
• Don’t mix new and old batteries or different types of
batteries.
• If you intend not to use the remote controller for a long time,
remove the batteries to prevent damage from leakage or
corrosion.
• Remove expired batteries as soon as possible to prevent
damage from leakage or corrosion.

Connections

Speaker Configuration

Connections

Connecting the AV
Receiver
Connecting Your Speakers
ab

cI J

The following table indicates the channels you should
use depending on the number of speakers that you
have.
No matter how many speakers you use, a powered
subwoofer is recommended for a really powerful and
solid bass.
To get the best from your surround sound system,
you need to set the speaker settings automatically
(➔ page 24) or manually (➔ page 55).
Number of speakers

2 3 4 5 6 7 7

Front speakers

✔✔✔✔✔✔✔
✔

Center speaker

✔✔✔✔
✔✔✔✔✔

Surround speakers

✔

Surround back speaker*1

✔

Surround back speakers*1

ab
c
de
f
GH
IJ

Tip
• If your subwoofer is unpowered and you’re using an
external amplifier, connect the subwoofer pre out jack to an
input on the amplifier.

Attaching the Speaker Cable Labels
The speaker terminals are color-coded for
identification purpose.
Speaker

Color

Front left, Front high left, Zone 2 left

White

Speaker Configuration
5.1-channel: a b c d e f
7.1-channel: a b c d e f + G H
7.1-channel: a b c d e f + I J

Front right, Front high right, Zone 2
right

Red

Surround back left

Brown

Surround back right

Tan

✔

Front high speakers*1

Front high and surround back speakers cannot be used
at the same time.

Using Powered Subwoofers

de GH
Front speakers
Center speaker
Surround speakers
Subwoofer(s)
Surround back speakers
Front high speakers

To find the best position for your subwoofer, while
playing a movie or some music with good bass,
experiment by placing your subwoofer at various
positions within the room, and choose the one that
provides the most satisfying results.
You can connect the powered subwoofer with two
SUBWOOFER PRE OUT jacks respectively.
The same signal is output from each jack.

En-12

Green

Surround left

Blue

Surround right

Gray

The supplied speaker cable labels are also colorcoded and you should attach them to the positive (+)
side of each speaker cable in accordance with the
table above. Then all you need to do is to match the
color of each label to the corresponding speaker
terminal.
Corner
position

1/3 of wall
position

Center

Connections

Connecting the Speaker Cables/Powered Subwoofers
Please connect a , b , c , d , e and f for 5.1-channel surround.
If you’re using only one surround back
speaker, connect it to the SURROUND
BACK or FRONT HIGH L terminals.

b
Front
speaker R

a
Front
speaker L

c
Center speaker

Red

Green

White

Before connecting the power cord, connect all of
your speakers and AV components. A setup wizard
is launched upon first-time use to let you perform
the settings.
• Read the instructions supplied with your speakers.
• By default, speakers for 7.1-channel surround are
configured to use: front right/front left/center/
surround right/surround left/surround back right/
surround back left/subwoofer.
■ Screw-type speaker terminals
Strip 1/2" to 5/8" (12 to 15 mm) of insulation from the
ends of the speaker cables, and twist the bare wires
tightly, as shown.
1/2" to 5/8" (12 to 15 mm)

■ Banana Plugs (North American models)
• If you are using banana plugs, tighten the speaker
terminal before inserting the banana plug.
• Do not insert the speaker code directly into the
center hole of the speaker terminal.
Gray

Powered
subwoofer
f

Surround
speaker R
e

Tan

Surround back or
Front high speaker R
HJ

Brown

Surround back or
Front high speaker L
GI

Blue

Surround
speaker L
d

• Pay close attention to speaker wiring polarity. In other words, connect positive (+) terminals only to positive (+)
terminals, and negative (–) terminals only to negative (–) terminals. If you get them the wrong way around, the
sound will be out of phase and will sound unnatural.

En-13

Connections
■ Speaker Connection Precautions
• (North American and Taiwanese models) You
can connect speakers with an impedance of
between 6 and 16 ohms. If you use speakers with a
lower impedance, and use the amplifier at high
volume levels for a long period of time, the built-in
amp protection circuit may be activated.
• (European, Australian and Asian models) You
can connect speakers with an impedance of
between 4 and 16 ohms. If the impedance of any of
the connected speakers is 4 ohms or more, but less
than 6 ohms, be sure to set the minimum speaker
impedance to “4ohms” (➔ page 55). If you use
speakers with a lower impedance, and use the
amplifier at high volume levels for a long period of
time, the built-in protection circuit may be activated.
• Unnecessarily long, or very thin speaker cables may
affect the sound quality and should be avoided.
• Be careful not to short the positive and negative
wires. Doing so may damage the AV receiver.
• Make sure the metal core of the wire does not have
contact with the AV receiver’s rear panel. Doing so
may damage the AV receiver.

• Don’t connect more than one cable to each speaker
terminal. Doing so may damage the AV receiver.
• Don’t connect one speaker to several terminals.

Bi-amping the Front Speakers
Important:
• When making the bi-amping connections, be sure to
remove the jumper bars that link the speakers’ tweeter
(high) and woofer (low) terminals.
• Bi-amping can be used only with speakers that support
bi-amping. Refer to your speaker manual.

Bi-amping provides improved bass and treble
performance.
When bi-amping is used, the AV receiver is able to
drive up to a 5.1 speaker system in the main room.
Perform bi-amping connections by using FRONT
terminals and SURROUND BACK or FRONT HIGH
terminals as shown below.
Once you’ve completed the bi-amping connections
and turned on the AV receiver, you must set the
speaker setting to enable bi-amping (➔ page 55).

Tweeter (high)
Woofer (low)

Front right

En-14

Front left

Connections

Connecting the TV/AV components

C Use this jack to connect to the Satellite/cable settop box, etc.

Before connecting the power cord, connect all of your speakers and AV components. To display the setup
menu on the TV screen, connecting the TV to HDMI OUT MAIN is required.

D Use this jack to connect to the game consoles,
etc.

F Use this port to connect to a LAN port on a router
so the AV receiver can be connected to your
home network.
G Use jack and terminal here to connect the
supplied FM antenna and AM loop antenna.
H Use this jack to make connections using an
analog audio cable.
With this connection, you can also enjoy analog
audio from external components while you are in
Zone 2.
I Use this jack to make connections using a
component video cable.
J Use this jack to connect to the camcorder/MHLenabled mobile device, etc.
Tip

If you select the input selector button, the signal from
the component connected to the assigned jack is
played.

• To prevent interference, keep audio and video
cables away from power cords and speaker cables.

Connections

Input
selector
buttons

• Before making any AV connections, read the
manuals supplied with your AV components.
• Push plugs in all the way to make good connections
(loose connections can cause noise or
malfunctions).

A Use this jack to connect to the HDMI input of the
TV. If your TV doesn’t support Audio Return
Channel (ARC)*1, you need to connect an optical
digital cable together with the HDMI cable to jack
E.
Another TV can be connected to the HDMI OUT
SUB jack.
*1

ARC is the function that carries the audio signal
from the TV to jack A. With ARC, a single HDMI
cable can connect the TV and the AV receiver.

B Use this jack to connect to your Blu-ray Disc/DVD
player, etc.

En-15

• To listen to the audio of a component connected via HDMI
through your TV’s speakers, enable “HDMI Through”
(➔ page 65) and set the AV receiver to standby mode.
• In the case of Blu-ray Disc/DVD players, if no sound is
output despite following the above-mentioned procedure,
set your Blu-ray Disc/DVD player’s HDMI audio settings to
PCM.
• Connect a turntable (MM) that has a built-in phono preamp
to TV/CD IN, or connect it to PHONO IN with the phono
preamp turned off. If your turntable (MM) doesn’t have a
phono preamp, connect it to PHONO IN. If your turntable
has a moving coil (MC) type cartridge, you’ll need a
commercially available MC head amp or MC transformer to
connect to PHONO IN. See your turntable’s manual for
details.
If your turntable has a ground wire, connect it to the AV
receiver’s GND screw. With some turntables, connecting
the ground wire may produce an audible hum. If this
happens, disconnect it.

Connections
■ MHL (Mobile High-Definition Link)
With its support for MHL (Mobile High-Definition Link),
HDMI IN 1 allows you to deliver high-definition video
from a connected mobile device.

MHL-enabled
mobile device, etc.

Connecting to the Network (Optional)
The following diagram shows how you can connect
the AV receiver to your home network. In this
example, it’s connected to a LAN port on a router,
which has a 4-port 100Base-TX switch built-in.
Network connection by wireless LAN is possible. See
“Performing Wireless LAN Setup” for connections
(➔ page 27).
Internet radio
WAN

Modem

p
The AV receiver allows interoperability of the CEC
(Consumer Electronics Control) specified in the HDMI
standard, which is known as RIHD. Various linked
operations can be performed by connecting the AV
receiver to an RIHD-compatible TV, player, or
recorder.
Default setting is set to off, so it is required to change
the setting to on.
Perform this setting after the initial setup.

Router

LAN

About RIHD-compatible components
The following components are p-compatible
(As of January 2013).
■ TV
• Sharp TV

Computer or media server

Do not connect the AV receiver’s USB port to a USB
port on your computer. Music on your computer
cannot be played through the AV receiver in this way.

■ Players/Recorders
• Onkyo and Integra p-compatible players
• Toshiba players and recorders
• Sharp players and recorders (only when used
together with Sharp TV)
*

The default of the assignment for the input selector buttons and jacks are as shown below. These settings can
be changed. (The assignment for the composite video jacks and the analog audio jacks cannot be changed.)
Input selector buttons HDMI jacks

COMPONENT VIDEO
jacks

DIGITAL IN COAXIAL
and OPTICAL jacks

Composite video and
analog audio jacks

DIGITAL IN
COAXIAL 1

VIDEO/AUDIO IN
BD/DVD

DIGITAL IN
COAXIAL 2

VIDEO/AUDIO IN
CBL/SAT

BD/DVD

HDMI IN 2

CBL/SAT

HDMI IN 3

GAME

HDMI IN 4

VIDEO/AUDIO IN
GAME

HDMI IN 5

VIDEO/AUDIO IN PC

AUX

HDMI IN 1

TV/CD

COMPONENT VIDEO
IN

VIDEO/AUDIO IN AUX
DIGITAL IN OPTICAL

PHONO

AUDIO IN TV/CD
AUDIO IN PHONO

En-16

Models other than those mentioned above may have some
interoperability if compatible with CEC, which is part of the
HDMI Standard, but operation cannot be guaranteed.
Note

• For proper linked operations, do not connect more
p-compatible components than the quantities
specified below, to the HDMI input terminal.
– Blu-ray Disc/DVD players: up to three.
– Blu-ray Disc/DVD recorders/Digital Video Recorders: up
to three.
– Cable/Satellite Set-top boxes: up to four.
• Do not connect the AV receiver to another AV receiver/AV
amplifier via HDMI.
• Proper linked operations are not guaranteed when more
p-compatible components than the abovementioned quantities are connected.

Connections

Operations that can be performed with
RIHD connection
■ For p-compatible TV
The following linked operations are enabled by
connecting the AV receiver to an p-compatible
TV.
• The AV receiver will enter standby mode when the
TV is set to standby.
• You can set on the menu screen of the TV to either
output the audio from the speakers connected to the
AV receiver, or from the speakers of the TV.
• It is possible to output the audio coming from the
tuner or auxiliary input of your TV to the speakers of
the AV receiver. (A connection such as an optical
digital cable or similar is required in addition to the
HDMI cable.)
• Input to the AV receiver can be selected with the
remote controller of the TV.
• Operations such as volume adjustment or similar for
the AV receiver can be performed from the remote
controller of the TV.
■ For p-compatible players/recorders
The following linked operations are enabled by
connecting the AV receiver to an p-compatible
player/recorder.
• When playback is started on the player/recorder, AV
receiver will switch to the HDMI input of the
player/recorder that is playing back.
• Operation of the player/recorder is possible using
the remote controller supplied with the AV receiver.
*

Depending on the model used, not all operations may be
available.
Note

• Do not assign an HDMI IN to the TV/CD selector at this
time, otherwise appropriate CEC (Consumer Electronics
Control) operation will not be guaranteed.

Confirm the settings
1. Turn on the power for all connected components.
2. Turn off the power of the TV, and confirm that the
power of the connected components is turned off
automatically with the link operation.
3. Turn on the power of the Blu-ray Disc/DVD
player/recorder.
4. Start playback on the Blu-ray Disc/DVD
player/recorder, and verify the following:
• The AV receiver automatically turns on, and
selects the input to which the Blu-ray Disc/DVD
player/recorder is connected.
• The TV automatically turns on, and selects the
input to which the AV receiver is connected.
5. Following the operating instructions of the TV,
select “Use the TV speakers” from the menu
screen of the TV, and confirm that the audio is
output from the speakers of the TV, and not from
the speakers connected to the AV receiver.
6. Select “Use the speakers connected from the AV
receiver” from the menu screen of the TV, and
confirm that the audio is output from the speakers
connected to the AV receiver, and not from the TV
speakers.

• On the TV, when you select anything other than the HDMI
jack to which the AV receiver is connected, the input on the
AV receiver will be switched to “TV/CD”.
• The AV receiver will automatically power on in conjunction
when it determines it to be necessary. Even if the AV
receiver is connected to an p compatible TV or
player/recorder, it will not power on if it is not necessary. It
may not power on in conjunction when the TV is set to
output audio from the TV.
• Linked functions with the AV receiver may not work
depending on the component model connected. In such
cases, operate the AV receiver directly.

Connection Tips
The video and audio signal flow
Connect the AV receiver between the AV
components and the TV. The signal from the AV
components is carried through the AV receiver. You
can enjoy the audio of the TV through the AV
receiver.
Blu-ray Disc/DVD player, etc.

Video, audio
AV receiver

Note
• Audio from DVD-Audio or Super Audio CD may not output
from the TV speakers. You will be able to output the audio
from the TV speakers by setting the audio output of the
DVD player to 2ch PCM. (It may not be possible depending
on the player models.)
• Even if you set to output audio on the TV speakers, audio
will be output from the speakers connected to the AV
receiver when you adjust the volume or switch the input on
the AV receiver. To output audio from the TV speakers, redo the corresponding operations on the TV.
• In case of an p connection with u and u audio
control compatible components, do not connect the u
cable at the same time.

En-17

Audio

Video, audio

TV, projector, etc.

Video components can be connected by using any
one of the following video connection formats:
composite video, component video, or HDMI, the
latter offering the best picture quality.
Video input signals flow through the AV receiver as
shown, with composite video and component video
sources all being upconverted for the HDMI output(s).

Connections
Signal Selection Example
Blu-ray Disc/DVD player, etc.

Video Signal Flow Chart
Blu-ray Disc/DVD player, etc.
Composite

Component

Composite

HDMI

Component

HDMI

AV receiver

MONITOR OUT

MONITOR OUT
Composite

Tip

Component

Composite

HDMI

Note
• In order for the AV receiver to upconvert component input
to HDMI output, the source output must be set to 480i/576i.
When signal is input at resolution of 480p/576p and more,
error message will be displayed.

■ Signal Selection
If signals are present at more than one input, the
inputs will be selected automatically in the following
order of priority: HDMI, component video, composite
video.
However, for component video only, regardless of
whether a component video signal is actually present,
if a component video input is assigned to the input
selector, that component video input will be selected.
And if no component video input is assigned to the
input selector, this will be interpreted as no
component video signal being present.
In the Signal Selection Example shown below, video
signals are present at both the HDMI and composite
video inputs. However, the HDMI signal is
automatically selected as the source and the video is
output by the HDMI outputs.

AV Cables and Jacks
■ HDMI
HDMI connections can carry digital video and audio.

TV, projector, etc.

The composite video and component video outputs
pass through their respective input signals as they are.

HDMI

Component

• When a signal is input via HDMI and the corresponding
input selector is selected, the HDMI indicator lights. In the
case of an optical or coaxial connection, the DIGITAL
indicator lights. In the case of an analog connection, neither
of the HDMI and DIGITAL indicators light.

• To by-pass the upconversion, set the “Picture
Mode” setting to “Bypass” (➔ page 61).
Audio components can be connected by using any of
the following audio connection formats: analog,
optical, coaxial, or HDMI.
When choosing a connection format, bear in mind
that the AV receiver does not convert digital input
signals for analog line outputs and vice versa.
If signals are present at more than one input, the
inputs will be selected automatically in the following
order of priority: HDMI, digital, analog.
Audio Signal Flow Chart
Blu-ray Disc/DVD player, etc.
Analog

Coaxial

Optical

HDMI

CB/PB

Blue

CR/PR

Red

Yellow
HDMI

TV, projector, etc.

Green

OUT

■ Composite video
Composite video is commonly used on TVs, DVDs,
and other video equipment.

AV receiver

■ Component video
Component video separates the luminance (Y) and
color difference signals (PB, PR), providing the best
picture quality (some TV manufacturers label their
component video sockets slightly differently).

Depends on the “Audio TV Out (Main)” or “Audio TV
Out (Sub)” setting (➔ page 65).
This is possible when “Audio Return Channel” is set to
“Auto” (➔ page 66), the TV/CD input selector is
selected, and your TV is ARC capable.

En-18

Connections
■ Optical digital audio
Optical digital connections allow you to enjoy digital
sound such as PCM*1, Dolby Digital or DTS. The
audio quality is the same as coaxial.

Connecting the Antennas
This section explains how to connect the supplied indoor FM antenna and AM loop antenna.
The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the
antenna to use the tuner.

■ Coaxial digital audio
Coaxial digital connections allow you to enjoy digital
sound such as PCM*1, Dolby Digital or DTS. The
audio quality is the same as optical.
Push.

Orange

■ Analog audio (RCA)
Analog audio connections (RCA) carry analog audio.

Insert wire.

Release.

Assembling the AM loop antenna

(North American and
Taiwanese models)

(European, Australian
and Asian models)

Insert the plug fully
into the jack.

Caution

• Be careful not to injure
yourself when using
thumbtacks.

White
Red

Thumbtacks, etc.
*1

For PCM signals, the supported sampling rates are
32/44.1/48/88.2/96 kHz. With HDMI connections, 176.4
and 192 kHz are also supported.

Note
• The AV receiver does not support SCART plugs.
• The AV receiver’s optical digital jacks have shutter-type
covers that open when an optical plug is inserted and close
when it’s removed. Push plugs in all the way.
Caution

• To prevent shutter damage, hold the optical plug
straight when inserting and removing.

AM loop antenna (supplied)

Indoor FM antenna (supplied)

Note
• Once your AV receiver is ready for use, you’ll need to tune into a radio station and position the antenna to achieve the best
possible reception.
• Keep the AM loop antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.
Tip
• If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna
instead.
• If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available
outdoor AM antenna.

En-19

Connections

Connecting Onkyo RI Components

Make sure that each Onkyo component is
connected with an analog audio cable
(connection H in the hookup examples)
(➔ page 15).

2
3

Make the u connection (see the illustration).

Using Headphones

While the headphones plug is inserted in the
PHONES jack, = indicator lights.
Note

If you’re using an RI Dock, or cassette tape
deck, change the Input Display (➔ page 46).

With u (Remote Interactive), you can use the
following special functions:
e.g., cassette tape deck

■ System On/Auto Power On
When you start playback on a component connected
via u, while the AV receiver is on standby, the AV
receiver will automatically turn on and select that
component as the input source.
■ Direct Change
When playback is started on a component connected
via u, the AV receiver automatically selects that
component as the input source.
■ Remote Control
You can use the AV receiver’s remote controller to
control your other u-capable Onkyo components,
pointing the remote controller at the AV receiver’s
remote control sensor instead of the component. You
must enter the appropriate remote control code first
(➔ page 72).

Connect a pair of stereo headphones with a
standard plug (1/4 inch or ø 6.3 mm) to the
PHONES jack.

R
L
ANALOG
AUDIO OUT

RI Dock
Note
• Use only u cables for u connections. u cables are
supplied with Onkyo components.
• Some components have two u jacks. You can connect
either one to the AV receiver. The other jack is for
connecting additional u-capable components.
• Connect only Onkyo components to u jacks. Connecting
other manufacturer’s components may cause a
malfunction.
• Some components may not support all u functions. Refer
to the manuals supplied with your Onkyo components.
• While Zone 2 is on, the System On/Auto Power On and
Direct Change u functions do not work.

En-20

• Always turn down the volume before connecting your
headphones.
• While the headphones plug is inserted in the PHONES
jack, the speakers are turned off. (The Zone 2
speakers are not turned off.)
• When you connect a pair of headphones, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, Direct, or Pure Audio (European, Australian
and Asian models).

Turning On & Basic Operations

Turning On & Basic
Operations

the same circuit. If this is a problem, plug the AV receiver
into a different branch circuit.
• Do not use a power cord other than the one supplied with
the AV receiver. The supplied power cord is designed
exclusively for use with the AV receiver and should not be
used with any other equipment.
• Never disconnect the power cord from the AV receiver
while the other end is still plugged into a wall outlet. Doing
so may cause an electric shock. Always disconnect the
power cord from the wall outlet first, and then the AV
receiver.

Turning Off

Press 8ON/STANDBY on the front panel.
or
Press RECEIVER followed by 8RECEIVER on
the remote controller.
The AV receiver will enter standby mode. To
prevent any loud surprises when you turn on the
AV receiver, always turn down the volume before
you turn it off.

Turning On

Turning On/Off the AV
Receiver
Connecting the Power Cord

(Taiwanese models)
Connect the supplied power cord to the AV
receiver’s AC INLET.

Tip

Press 8ON/STANDBY on the front panel.
or
Press RECEIVER followed by 8RECEIVER on
the remote controller.
The AV receiver comes on and its display lights.

■ Smooth Operation in a Few Easy Steps
(Initial Setup)
To ensure smooth operation, here’s a few easy steps
to help you configure the AV receiver before you use
it for the very first time. These settings only need to
be made once. See “Initial Setup” for details
(➔ page 22).

To AC wall outlet

Plug the power cord into an AC wall outlet.

Note
• Before connecting the power cord, connect all of your
speakers and AV components.
• Turning on the AV receiver may cause a momentary power
surge that might interfere with other electrical equipment on

En-21

• The HYBRID STANDBY indicator may light depending on
the status of settings (➔ page 22).
• For details on power management settings, see “Auto
Standby” (➔ page 66).
• If the HDMI Through setting is not set in standby mode, an
MHL-enabled mobile device cannot be charged even if it is
connected.

Turning On & Basic Operations

Firmware Update Notification
When a new version of the firmware is available, the
notification window “Firmware Update Available”
pops up. This notification only appears when the AV
receiver is connected to the Internet (➔ pages 16,
27). To perform the firmware update, follow the
instructions on screen.
Use q/w and ENTER on the AV receiver or remote
controller to select one of the options.
` Update Now:
Starts the firmware update.
Refer to “Firmware Update” (➔ page 85).
` Remind me Later:
The update notification will pop up again the
next time you turn the AV receiver on.
` Never Remind me:
Disables the automatic update notification.
Tip
• The update notification window can be enabled or disabled
in “Update Notice” (➔ page 67).

About the HYBRID STANDBY indicator
By way of optimized circuitry, this function reduces
power consumption when the AV receiver is in
standby mode. The HYBRID STANDBY indicator will
light in either of the following conditions:
–“HDMI Through” is enabled (the HDMI indicator is
off).
–“Network Standby” is enabled (the NET indicator
is off).

Initial Setup

This section explains the settings that we recommend
you to make before using the AV receiver for the very
first time. A setup wizard is launched upon first-time
use to let you perform those settings.
Tip
• The on-screen menus appear only on a TV that is
connected to HDMI OUT MAIN.

Selecting the Language for the Onscreen Setup Menus
This step determines the language used for the onscreen setup menus. See “Language” in “OSD
Setup” (➔ page 64).

Use q/w on the AV receiver or remote
controller to select one of the following
options, and then press ENTER.
` Yes:
Continues to “Audyssey MultEQ: Auto
Setup”.
` No:
Skips the settings and terminates the initial
setup. The setup wizard goes to
“Terminating the Initial Setup” (➔ page 23).
You can always restart the initial setup by
selecting “Initial Setup” in the “Hardware
Setup” menu (➔ page 68).

Audyssey MultEQ: Auto Setup

Tip
• Pressing HOME will close the setup wizard. To restart the
initial setup, select “Initial Setup” in the “Hardware Setup”
menu (➔ page 68).

After selecting the language for on-screen setup
menus, a welcome screen is displayed.
Initial Setup
Welcome to initial setup. Have you connected all the speakers and devices?
Before starting, please connect speakers and sources.
Now, would you like to start initial setup?
1st Step : Audyssey MultEQ: Auto Setup
2nd Step : Source Connection
3rd Step : Remote Mode Setup
4th Step : Network Connection
Yes
No
HOME Exit

Note
• If Zones are turned on or, if a mobile device connected to
HDMI IN 1 (MHL) is charging, the HYBRID STANDBY
indicator won’t light.

En-22

This step performs the automatic speaker setup.

Use q/w to select one of the following options,
and then press ENTER.
` Do it Now:
The automatic speaker setup is performed
following instructions on screen. Refer to
step 2 of “Using the Automatic Speaker
Setup” (➔ page 24). When this setting is
complete, the setup wizard continues to
“Source Connection”.
` Do it Later:
Skips this setting.
Press ENTER and continue to “Source
Connection”.

Turning On & Basic Operations

Source Connection

Remote Mode Setup

This step checks the connection of source
components.

With this step, you can enter remote control codes for
the components you want to operate.

Use q/w to select one of the following options,
and then press ENTER.
`Yes, Continue:
Performs the checkings.
`No, Skip:
Skips this step and continues to “Remote
Mode Setup”.
Select the input selector for which you want to
check the connection and press ENTER.
The picture and sound of the corresponding
source should appear on screen with a
verification prompt.
When prompted, use q/w to select one of the
following options and then press ENTER.
`Yes:
Confirms that the source is properly
displayed.
`No:
Displays an error report. Follow the
troubleshooting instructions and recheck the
source.
Use q/w to select one of the following options,
and then press ENTER.
`Yes:
Returns to step 2.
`No, Done Checking:
The setup wizard continues to “Remote
Mode Setup”.

Use q/w to select one of the following options,
and then press ENTER.
` Yes:
Performs the remote control code input.
Refer to step 5 of “Looking up for Remote
Control Codes” (➔ page 71).
` No, Skip:
Skips this step and continues to “Network
Connection”.

Follow the instructions on screen to perform
the network checking.
The checking is complete when the message
“Successfully connected.” appears at the
middle of the screen. Press ENTER to terminate
the initial setup.
Tip
• If you have selected “Wireless”, you need to perform
the wireless LAN setup. See “Performing Wireless
LAN Setup” (➔ page 27). This completes the initial
setup.

When you’re finished, select one of the
following options and press ENTER.
` Yes, Done:
The setup wizard continues to “Network
Connection”.
` No, not yet:
You can enter other remote control codes.

If an error message appears, select one of the
following options and press ENTER.
` Retry:
Performs the checking again.
` No, Do it Later:
Skips this step and terminates the initial
setup. The setup wizard goes to
“Terminating the Initial Setup”.

Terminating the Initial Setup
Network Connection
This step checks your network connection.

Use q/w to select one of the following options,
and then press ENTER.
` Yes:
Performs the checkings.
` No, Skip:
Skips this step and terminates the initial
setup.

En-23

This step ends the initial setup process.

Press ENTER.
To restart the initial setup, select “Initial Setup”
in the “Hardware Setup” menu (➔ page 68).

Turning On & Basic Operations

Using the Automatic Speaker Setup
With the supplied calibrated microphone,
Audyssey MultEQ® automatically determines the
number of speakers connected, their size for
purposes of bass management, optimum crossover
frequencies to the subwoofer (if present), and
distances from the primary listening position.
Audyssey MultEQ then removes the distortion caused
by room acoustics by capturing room acoustical
problems over the listening area in both the frequency
and time domain. The result is clear, well-balanced
sound for everyone. Audyssey MultEQ can be used
with Audyssey Dynamic EQ® and
Audyssey Dynamic Volume® (➔ page 59).
Before using this function, connect and position all of
your speakers.
Audyssey MultEQ offers two ways of measuring: the
“Audyssey Quick Start” and “Audyssey MultEQ
Full Calibration”.
• “Audyssey Quick Start” uses the measurement
from one position to perform the speaker setting
only.
• “Audyssey MultEQ Full Calibration” uses the
measurement from six positions to correct room
response in addition to the speaker setting.
The more positions are used in measuring, the better
the listening environment will become. We
recommend using a measurement from six positions
to create the best listening environment.
The Quick Start takes 2 minutes and Full Calibration
takes about 15 minutes.
Total measurement time varies depending on the
number of speakers.

Measurement procedure
To create a listening environment in your home
theater that all listeners will enjoy, Audyssey MultEQ
takes measurements at up to six positions within the
listening area. Position the microphone at ear height
of a seated listener with the microphone tip pointed
directly at the ceiling using a tripod. Do not hold the
microphone in your hand during measurements as
this will produce inaccurate results.
■ First measurement position
Also referred to as the Main Listening Position, this
refers to the most central position where one would
normally sit within the listening environment.
Audyssey MultEQ uses the measurements from this
position to calculate speaker distance, level, and the
optimum crossover value for the subwoofer.
■ Second-sixth measurement positions
These are the other listening positions (i.e., the
places where the other listeners will sit). You can
measure up to six positions.

def
cab

: Listening area

a to f: Listening position

En-24

Note
• Make the room as quiet as possible. Background noise and
Radio Frequency Interference (RFI) can disrupt the room
measurements. Close windows, televisions, radios, air
conditioners, fluorescent lights, home appliances, light
dimmers, or other devices. Turn off the cell phone (even if
it is not in use) or place it away from all audio electronics.
• The microphone picks up test tones played through each
speaker as Audyssey MultEQ Room Correction and
Speaker Setup runs.
• Audyssey MultEQ Room Correction and Speaker Setup
cannot be performed while a pair of headphones is
connected.

Turning On & Basic Operations

Turn on the AV receiver and the connected TV.
On the TV, select the input to which the AV
receiver is connected.

Set the speaker setup microphone at the Main
Listening Position a, and connect it to the
SETUP MIC jack.

Use q/w to select “Audyssey Quick Start” or
“Audyssey MultEQ Full Calibration”, and then
press ENTER.

Press ENTER.
Audyssey MultEQ® Room Correction and
Speaker Setup starts.
Test tones are played through each speaker as
Audyssey MultEQ Room Correction and Speaker
Setup runs. This process takes a few minutes.
Please refrain from talking during
measurements and do not stand between
speakers and the microphone.
Do not disconnect the speaker setup microphone
during Audyssey MultEQ Room Correction and
Speaker Setup, unless you want to cancel the
setup.
If you select “Audyssey Quick Start”, you will go
to step 9.

Note

When you’ve finished making the settings,
press ENTER.
MultEQ: Auto Setup
AUDYSSEY

Normal
No
Surround Back
Yes

Perform the “2. Speaker Setup” according to your
speaker configuration:
– Speakers Type (Front) (➔ page 55)
– Powered Zone 2 (➔ page 55)
– Surround Back/Front High (➔ page 56)
– Subwoofer (➔ page 56)

If you use a powered subwoofer(s), go to step 4.
If not, go to step 5.

MultEQ: Auto Setup
AUDYSSEY

Subwoofer
Front
Center
Surround
Front High
Surround Back
Surround Back Ch

• If your subwoofer does not have a volume control,
disregard the displayed level and press ENTER to
proceed to the next step.
• If you set the subwoofer’s volume control to its
maximum and the level displayed is lower than 75 dB,
leave the subwoofer’s volume control at its maximum
and press ENTER to proceed to the next step.

• The on-screen menus appear only on a TV that is
connected to HDMI OUT MAIN. If your TV is
connected to other video outputs, use the AV
receiver’s display when changing settings.

Speakers Type (Front)
Powered Zone 2
Surround Back/Front High
Subwoofer

Use q/w to select an option, and then press
ENTER.

-- Review Speaker Configuration --

Speaker setup microphone

Note

SETUP MIC jack

The speaker setting menu appears.

Adjust the subwoofer volume level to 75 dB,
and then press ENTER.
Test tones are played through the subwoofer.
Use the volume control on the subwoofer.

Place the speaker setup microphone at the
next position, and then press ENTER.
Audyssey MultEQ performs more
measurements. This takes a few minutes.

When prompted, repeat step 7.

En-25

Yes
100Hz
40Hz
100Hz
None
120Hz
2ch

Save
Cancel

The options are:
` Save:
Save the calculated settings and exit
Audyssey MultEQ Room Correction and
Speaker Setup.
` Cancel:
Cancel Audyssey MultEQ Room Correction
and Speaker Setup.
Tip
• You can view the calculated settings for the speaker
configuration, speaker distances, and speaker levels
by using e/r.

Use q/w to select a target, and use e/r to
change the setting.
After the results of Audyssey MultEQ have been
saved, the menu will display the “Audyssey”
(➔ page 58), “Dynamic EQ” (➔ page 59),
“Dynamic Volume” (➔ page 59) settings.
Note
• When “Audyssey Quick Start” has been used for
measurement, “Audyssey” cannot be selected.
• These settings are applied to all input selectors.

11
12

Press ENTER.
Disconnect the speaker setup microphone.

Turning On & Basic Operations
Note
• You can cancel Audyssey MultEQ® Room Correction and
Speaker Setup at any point in this procedure simply by
disconnecting the setup microphone.
• Do not connect or disconnect any speakers during
Audyssey MultEQ Room Correction and Speaker Setup.
• If the AV receiver is muted, it will be unmuted automatically
when Audyssey MultEQ Room Correction and Speaker
Setup starts.
• Changes to the room after Audyssey MultEQ Room
Correction and Speaker Setup requires you run
Audyssey MultEQ Room Correction and Speaker Setup
again, as room EQ characteristics may have changed.

Error Messages
While Audyssey MultEQ Room Correction and
Speaker Setup is in progress, one of the error
messages below may appear.
MultEQ: Auto Setup
AUDYSSEY

Ambient noise is too high.

Retry
Cancel

Error message

The options are:
` Retry:
Try again.
` Cancel:
Cancel Audyssey MultEQ Room Correction and
Speaker Setup.
• Ambient noise is too high.
The background noise is too loud. Remove the
source of the noise and try again.
• Speaker Matching Error!
The number of speakers detected was different
from that of the first measurement. Check the
speaker connection.
• Writing Error!
This message appears if saving fails. Try saving
again. If this message appears after 2 or 3
attempts, contact your Onkyo dealer.
• Speaker Detect Error
This message appears if a speaker is not detected.
“No” means that no speaker was detected.
Tip
• See “Speaker Configuration” for appropriate settings
(➔ page 12).

En-26

The setup of the speaker can be done manually
(➔ page 55).
The setup of the volume level of each speaker also
can be done manually (➔ pages 56, 57).

Using a Powered Subwoofer
If you’re using a powered subwoofer and it outputs
very low-frequency sound at a low volume level, it
may not be detected by Audyssey MultEQ Room
Correction and Speaker Setup.
If the “Subwoofer” appears on the “Review Speaker
Configuration” screen as “No”, increase the
subwoofer’s volume to the half-way point, set it to its
highest crossover frequency, and then try running
Audyssey MultEQ Room Correction and Speaker
Setup again. Note that if the volume is set too high
and the sound distorts, detection issues may occur,
so use an appropriate volume level. If the subwoofer
has a low-pass filter switch, set it to Off or Direct.
Refer to your subwoofer’s instruction manual for
details.

Turning On & Basic Operations

Performing Wireless LAN Setup

A wireless LAN (WLAN) is a local area network that
relies on wireless communication.
To achieve a wireless network connection, you will
need the following component:
■ Access point
Also known as the base station, it links your AV
receiver (wireless client) with a PC or network.
Access points fall into two categories: the bridge
type that only performs data relay in a local area
network, or the router type that has a built-in router
functionality.
To achieve a wireless network connection, it is
necessary to perform the wireless LAN setup. The
setup can be done either automatically or manually.
You use your AV receiver as a wireless client
(wireless terminal) and connect it to a PC or to the
Internet.

Automatic wireless LAN setup

1
2

Press RECEIVER followed by HOME.

Use q/w to select “Hardware Setup”, and then
press ENTER.

Use e/r or q/w to select “Setup”, and then
press ENTER.

Use q/w to select “Network”, and then press
ENTER.

■ PIN code method
1. Use q/w to select “PIN Code” and then press
ENTER.
An 8-digit PIN code is displayed. The PIN
code is displayed scrolling on the AV
receiver’s display.
2. Input the provided code in your Access Point.
For information on the registration process,
please refer to the instruction manual
provided with your Access Point device.

Use q/w to select “Network Connection”, and
e/r to select “Wireless”, and then press
ENTER (➔ page 67).
The “Wireless Setup” menu is displayed on
screen.
Tip
• The same setting is available even if “Wireless” is
selected in “Network Connection” in initial setup
(➔ page 23).

Press q/w to select (North American models)
“Push Button Configuration (Other
Routers)”*1/(excluding North American
models) “Push Button Configuration (Select
from Router)”, and press ENTER.
The method to make settings by “Push Button
Configuration” is displayed, providing the
following two options:
Tip
*1

(North American models) To connect to Linksys
E/EA Router, select “Push Button Configuration
(Linksys E/EA Router)” and make settings
following the instructions on the screen.

■ Push Button method
1. Use q/w to select “Push Button” and then
press ENTER.
2. Press the WPS button on your Access Point
device.
Tip
• How long the WPS button should be pressed differs
depending on the type of Access Point device. Refer
to the instruction manual provided with your Access
Point device for operations.

En-27

Press ENTER to confirm.
Connection to your Access Point starts and Wi-Fi
indicator flashes. After the connection to your
Access Point is completed, Wi-Fi indicator lights
and the connection status is displayed on the
screen.
This completes the wireless LAN setup.
You can review your setup with the “Status”
option on the “Wireless Setup” menu.
Note
• If Wi-Fi indicator doesn’t light, the connection to your
Access Point is not done successfully. Configure this
setting again (➔ page 80).

Turning On & Basic Operations

Manual wireless LAN setup

1
2

Press RECEIVER followed by HOME.

Use q/w to select “Hardware Setup”, and then
press ENTER.

Use q/w to select “Network”, and then press
ENTER.

Use e/r or q/w to select “Setup”, and then
press ENTER.

Use q/w to select “Search Wireless Network”
and then press ENTER.
A list of available Access Points is displayed.
Tip
• If Access Point you wish to connect to is not displayed
in the list of available Access Points, the setting also
can be made by entering “SSID”, “Security”, and
“Password” manually after selecting “Direct Input”.

Use q/w to select the Access Point you wish to
connect to, and then press ENTER.
Depending on your encryption settings, the
security of your Access Point will provide one of
the following patterns:
■ WEP method
1. Use q/w to select “Default Key ID” and then
press ENTER.
2. Use q/w to choose an ID between 1 and 4,
and then press ENTER.
3. Use q/w to select “Password” and then press
ENTER.
4. Use the keyboard on screen to enter the
password and confirm with “OK”.
■ WPA/WPA2 method
1. Use q/w to select “Password” and then press
ENTER.
2. Use the keyboard on screen to enter the
password and confirm with “OK”.
■ No encryption
If your Access Point device is not secured by
encryption, there is no need to input any secret
key.

Tip
• When you select the Access Point you wish to connect to
from the list of available Access Points, “SSID” and
“Security” are automatically displayed. These settings can
be changed manually.

En-28

Select “OK” and press ENTER.
Connection to your Access Point starts and Wi-Fi
indicator flashes. After the connection to your
Access Point is completed, Wi-Fi indicator lights
and the connection status is displayed on the
screen.
This completes the wireless LAN setup.
You can review your setup with the “Status”
option on the “Wireless Setup” menu.
Note
• If Wi-Fi indicator doesn’t light, the connection to your
Access Point is not done successfully. Configure this
setting again (➔ page 80).

Playback

• “Playing Music Files on a Shared Folder”
(➔ page 36)
• “Remote Playback” (➔ page 37)
• “Listening to AM/FM Radio” (➔ page 38)
• “Playing Audio and Video from Separate Sources”
(➔ page 40)
• “Controlling Other Components” (➔ page 71)
• “Using the Onkyo Dock” (➔ page 75)

* For the CEC compatible TV and the AV components
connected with HDMI connections, switching the input
is automatically performed. Switch the input manually
for other AV components.

1
2

Playback
4

This section describes the basic operation such as
playback, listening mode, and other useful functions.
Reading this manual from the beginning to this
section helps you to understand the basic
connection/setup/operation.
■ Screen Saver
If there is no video signal on the current input source
and no operation for a specific time (three minutes by
default), a screen saver automatically comes on.

Select the desired listening mode.
You can enjoy various types of listening mode.
The listening mode is switched by pressing
Listening mode button on the AV receiver or the
remote controller.

Adjust the volume.
You can enjoy the surround sound.

Tip

• The time until the screen saver activates itself can
be changed in the “Screen Saver” setting
(➔ page 64).
• The screen will return to its previous state if the AV
receiver is operated.
See also:
• “Playing an Audio from Bluetooth-enabled Device”
(➔ page 31)
• “Playing a USB Device” (➔ page 32)
• “Listening to TuneIn” (➔ page 32)
• “Registering Other Internet Radio” (➔ page 34)
• “Playing Music Files on a Server (DLNA)”
(➔ page 34)

Select the input on the AV receiver to play the
AV components.
Press the input selector button to which the AV
components to be played is connected.
Press the TV/CD button to play the audio of the
TV. Switching the input on the TV is also
required. Select the input to which the AV
receiver is connected by using the TV remote
controller.

(Actual location of buttons depends on the country.)

Turn on the AV receiver, the TV and the AV
components.
* When you operate the AV receiver with the remote
controller, press the RECEIVER button first.

En-29

• When listening to an HDMI component through the AV
receiver, set the HDMI component so that its video can be
seen on the TV screen (on the TV, select the input of the
HDMI component connected to the AV receiver). If the TV
power is off or the TV is set to another input source, this
may result in no sound from the AV receiver or the sound
may be cut off.

Playback

Controlling Contents of USB or
Network Devices
(➔ page 31)
Press USB or NET first.

a TOP MENU
This button displays the top menu for each media or
service.
b q/w and ENTER
These buttons navigate through the menus.

e/r
This button cycles through pages.
c 1
This button starts playback.
d 7
This button selects the beginning of the current song.
Pressing this button twice selects the previous song.

e 5
This button fast-reverses the current song.
f 3
This button pauses playback.

a
b
c
d
e
f
g

i
j
k
l
m
n
o

g SEARCH
You can toggle between the playback screen and the
list screen during playback.
h DISPLAY
This button switches between song information during
playback.
Press this button while the list screen is displayed to
return to the playback screen.
i MENU
This button displays the menu of Internet radio
services.
j RETURN
This button returns to the previous menu.
k 4
This button fast-forwards the current song.
l 6
This button selects the next song.
m 2
This button stops playback.
n RANDOM
This button performs random playback.

En-30

o REPEAT
Press this button repeatedly to cycle through the repeat
modes.
Tip
• See “Controlling Other Components” about the operation of
other components (➔ page 71).
• The AV receiver supports Album art display, and displaying
image file format of JPEG, PNG, and BMP is possible. The
image file format cannot be displayed in either of the
following cases:
– Total number of horizontal and vertical pixels is more than
2048 x 2048.
– Image data size (JPEG/PNG) is more than 4 MB.
Note
• The buttons you can use will differ depending on the
devices and media used for playback.
• When you select the NET input selector on the AV receiver
for the first time, “DISCLAIMER” screen is displayed on TV.
Please read the contents thoroughly before using network
service. Select “Agree” if you agree with the content. If you
disagree, network service is not available on the AV
receiver (➔ page 84).

Playback

Understanding Icons on the Display
This section describes icons that appear on the AV
receiver’s display during media playback.
Icon

Description
Folder
Track
Playback
Pause
Fast Forward
Fast Reverse
Artist

Playing an Audio from Bluetoothenabled Device
About the Bluetooth Wireless Technology
Bluetooth wireless technology is a short-range
wireless technology that enables wireless data
communication between digital devices. Bluetooth
wireless technology operates within a range of about
15 meters (49 feet). You do not need to use a cable
for connection, nor is it necessary for the devices to
face one another, such is the case with infrared
technology.
Tip
• The on-screen menus appear only on a TV that is
connected to HDMI OUT MAIN.
• If your Bluetooth-enabled device supports A2DP protocol,
its audio file will play through the AV receiver.
• Connection is not guaranteed for all Bluetooth-enabled
devices.

Album

Operating on the Remote Controller
Repeat One Track
Repeat Folder (USB Device)

The Bluetooth-enabled device can be operated by the
supplied remote controller.
Tip

Repeat
Shuffle

• To operate your Bluetooth-enabled device by the remote
controller, the Bluetooth-enabled device must support
profile: AVRCP.
• Operation by the remote controller is not guaranteed for all
Bluetooth-enabled devices.

En-31

Pairing the AV receiver with a Bluetoothenabled device
Pairing is an operation where Bluetooth-enabled
devices register with each other beforehand. Use the
procedure below to pair the AV receiver with your
Bluetooth-enabled device. Once a pairing operation is
performed, it does not need to be performed again.

Place the Bluetooth-enabled device within
1 meter (3.3 feet) from the AV receiver.

Select “BLUETOOTH” in “Input” in Quick
Setup, and press ENTER (➔ page 48).
BLUETOOTH indicator flashes and the AV
receiver is put to pairing mode.
“Now Pairing” appears on the AV receiver’s
display.
Tip
• The same operation can be done by pressing
BLUETOOTH button on the AV receiver.
• When connecting a Bluetooth-enabled device paired
with the AV receiver to the AV receiver, BLUETOOTH
input selector is automatically selected.
• If you connect the AV receiver to another Bluetoothenabled device, hold down BLUETOOTH button until
BLUETOOTH indicator flashes or make settings in
“Status” of “Bluetooth” for pairing (➔ page 68).
• Some Bluetooth-enabled device may need to reestablish pairing for each connection.
Note
• “BLUETOOTH” cannot be selected, if you’ve selected
NET or USB as input selector in Zone 2.

Playback

During this period (about 2 minutes), you can
operate the Bluetooth-enabled device to pair
with the AV receiver.
Note
• When establishing a connection with the AV receiver,
select the profile (A2DP, AVRCP) at the Bluetoothenabled device. If the Bluetooth-enabled device does
not support the AVRCP profile, you cannot perform
playback or other operations with the AV receiver.
Tip
• For details on the Bluetooth connection, refer to the
instruction manual of the Bluetooth-enabled device.

Once the AV receiver is detected and the
model name of the AV receiver appears on the
display of your Bluetooth-enabled device,
select the model name.
When a Bluetooth connection is established
successfully, BLUETOOTH indicator will light.
Tip
• The model name appeared on the display of your
Bluetooth-enabled device is “Onkyo TX-NR626”.

If passkey* is required on the display of the
Bluetooth-enabled device, enter “0000”.
The AV receiver only supports numerical
passkey up to 4 digits.
* Passkey may be called “Passcode”, “PIN code”, “PIN
number” or “Password”.

Play back the desired music on the Bluetoothenabled device.
The audio is output from the AV receiver.

Tip
• The AV receiver may not work as normal depending on the
circumstance even though the AV receiver is placed within
the 15 meters range. In such cases, get the Bluetoothenabled device closer to the AV receiver and retry the
operation.

• When disconnecting on your Bluetooth-enabled device,
BLUETOOTH indicator on the AV receiver will go off.
• If there is no sound output even after the pairing is done
successfully, consult the instruction manual of the
Bluetooth-enabled device, and then select the model name
of the AV receiver as the audio output device.
• While connected to a Bluetooth-enabled device, the AV
receiver cannot be detected and a connection cannot be
established from another Bluetooth-enabled device.
• If you cannot connect with a paired Bluetooth-enabled
device, perform the pairing operation between the AV
receiver and the Bluetooth-enabled device again.
Note
• Due to the characteristic of Bluetooth wireless technology,
the sound played on the AV receiver may slightly delay from
the sound played on the Bluetooth-enabled device.

Playing a USB Device
Tip
• The on-screen menus appear only on a TV that is
connected to HDMI OUT MAIN.

Note
• While the message “Connecting...” appears on the AV
receiver’s display, do not disconnect the USB cable
supplied with the USB device from the USB port.

Listening to TuneIn
You need to connect the AV receiver to your home
network (➔ pages 16, 27).
Tip
• The on-screen menus appear only on a TV that is
connected to HDMI OUT MAIN.

TuneIn is a new radio service which offers the music,
sports and news all over the world.
Over 70,000 radio stations and 2 million on-demand
programs are registered, and you can easily enjoy
them by selecting stations or programs of your
choice. TuneIn is preprogrammed on the AV receiver.

This section explains how to play music files from a
USB device (e.g., USB flash drives and MP3 players).
See also:
• “Network/USB Features” (➔ page 89).

1
2

Press USB to select the “USB” input.
Plug your USB device into the AV receiver’s
USB port.
The USB indicator lights. It will flash if the AV
receiver cannot read the USB device.

Press ENTER.
A list of the device’s contents appears. To open a
folder, use q/w to select it, and then press
ENTER.

Use q/w to select a music file, and press
ENTER or 1 to start playback.

En-32

Press NET.
The network service screen appears, and the
NET indicator lights. If it flashes, the AV receiver
is not connected to the network correctly. If wired
LAN connection is selected, verify that the
Ethernet cable is firmly connected to the AV
receiver. If wireless LAN connection is selected,
verify that the Wi-Fi indicator lights.
Tip
• The same operation can be done by selecting
“Network Service” in the Home menu.

Use q/w/e/r to select “TuneIn” and then
press ENTER.

Playback

Use q/w to select a station or a program, and
then press ENTER.
Playback starts.
tunein

My Music
0 : 11
Great Artist
My Favorite
Go to Menu

Setting an TuneIn account
To create a user account for TuneIn, open a browser
window such as Internet Explorer®, and connect to
tunein.com website. With a TuneIn account, you can
quickly search and browse for stations and programs
at tunein.com website and save as your favorites
which will automatically appear in your AV receiver
My Presets account. If you have a TuneIn account,
select “Login” and then “I have a TuneIn account”
on the top list. Enter your user name and password to
login.
Tip

Either of the following menus can be selected by
pressing the MENU button on the remote controller or
pressing ENTER button to select “Go to Menu”.
` Add to My Presets
In this menu, stations or programs can be stored
in “My Presets”.
` Remove from My Presets
In this menu, stations or programs stored in “My
Presets” can be deleted.
` Report a problem
This menu is used to report problems on TuneIn
service or resolve the problems in a wizard style.
` View Schedule
In this menu, program listings of stations or
programs can be displayed.
` Clear recents
In this menu, all the stations and programs
stored in “Recents” can be deleted.
` Add to My Favorites
In this menu, stations or programs can be stored
in “My Favorites”.

• Select “Login with a registration code”, and associate a
device from my page on TuneIn website by using a
registration code displayed on the screen. This allows you
to login without entering a user name and a password.

Adding TuneIn radio stations or programs to
My Favorites/My Presets
There are two ways you can register specific Internet
radio stations (programs) from the TuneIn.
• Adding to My Favorites
The selected program will be added to “My
Favorites” on the network service screen, which
appears when pressing NET.
1. Select radio stations or programs, and press
MENU button on the remote controller.
2. Use q/w to select “Add to My Favorites”, and
press ENTER.
3. Use q/w/e/r to select “OK”, and press ENTER.
Tip
• You can rename the stations saved in “My Favorites”
(➔ page 34).

En-33

• Adding TuneIn radio stations or programs to My
Presets
Select "TuneIn", and press ENTER button to display
a folder of “My Presets” on the screen that displays
Category/Area, etc. Store your favorite stations or
programs in this folder.
1. Select radio stations or programs, and press
MENU button on the remote controller.
2. Use q/w to select “Add to My Presets”, and
press ENTER.
Tip
• If no radio stations or programs are stored in “My Presets”,
“My Presets” folder will not be displayed.

Playback

Registering Other Internet Radio
You need to connect the AV receiver to your home
network (➔ pages 16, 27).
Tip
• The on-screen menus appear only on a TV that is
connected to HDMI OUT MAIN.

Internet radio URLs in the following formats are
supported: PLS, M3U, and podcast (RSS). However,
depending on the type of data or audio format used
by the Internet radio station, you may not be able to
listen to some stations.
To listen to other Internet radio stations, you must
register your station in “My Favorites” of the network
service screen, as described below.
Note
• Services available may vary depending on the region. See
the separate instructions for more information.
• Certain network service or contents available through this
device may not be accessible in case the service provider
terminates its service.

Select “Network” on the Setup menu to verify
your IP address (➔ page 67).
Take a note of the IP address.

2
3

On your computer, start your web browser.

Click “Save” to save the Internet radio station.
The Internet radio station is then added to “My
Favorites”. To play the registered station, press
NET, and then select “My Favorites” on the
network service screen. A list of registered
Internet radio stations appears. Select the one
that you saved and press ENTER.

Changing the Icon Layout on the
Network Service Screen
Tip
• You need to connect your TV to the HDMI output (HDMI
OUT MAIN) to make the following on-screen setting.

The layout of icons can be customized by switching
their positions on the network service screen.

Tip
• If you want to add a new station directly from “My
Favorites”, select an empty slot in the list and press MENU.
Then, select “Create New Station” and press ENTER.
Pressing ENTER again will display the keyboard screen.
Use that keyboard to enter the station’s name and URL
respectively, and then press ENTER.
• If you want to delete a station saved in “My Favorites”,
press MENU with the station selected or while the station is
playing. Then, use q/w to select “Delete from My
Favorites” and press ENTER. You can also delete stations
from the Web Setup.
• If you want to rename a station, select the desired station
and press MENU. Then, use q/w to select “Rename this
station” and press ENTER.
• You can save up to 40 Internet radio stations.

Press NET.
The network service screen appears.
Tip
• The same operation can be done by selecting
“Network Service” in the Home menu.

2
3

Press MODE/D (blue) on the remote controller.

Use q/w/e/r to select another icon as the
destination, and then press ENTER.
The icons switch positions and the message
“Completed!” appears.

Use q/w/e/r to select an icon to move, and
then press ENTER.

Playing Music Files on a Server (DLNA)
You need to connect the AV receiver to your home
network (➔ pages 16, 27).

Enter the AV receiver’s IP address in the
browser’s Internet address (URL) field.
If you are using Internet Explorer®, you can also
enter the URL by selecting “Open...” on the “File”
menu.
Information on the AV receiver is then shown on
your Internet browser (Web Setup).

Tip
• The on-screen menus appear only on a TV that is
connected to HDMI OUT MAIN.

This section explains how to play music files on a
computer or media server through the AV receiver
(Server Playback).

Click on the “My Favorites” tab, and enter the
Internet radio station’s name and URL.

En-34

Playback

Windows Media Player Setup

■ Windows Media Player 11 Setup
This section explains how to configure Windows
Media Player 11 so that the AV receiver can play the
music files stored on your computer.

1
2

Start Windows Media Player 11.

On the “Stream” menu, select “Turn on media
streaming”.
A dialog box appears.
Tip

Select the “Share my media” check box, and
then click “OK”.
A list of the supported devices appears.

Move your cursor and click on “Turn on media
streaming”.
A list of media server appears. Wording may vary
slightly depending on the network location.

Select the AV receiver in the list, and then
click “Allow”.
The corresponding icon will be checked.

On the “Media streaming options”, select the
AV receiver and confirm that it is set to
“Allowed”.

Click “OK” to close the dialog box.
This completes the Windows Media Player 11
configuration.
You can now play the music files in your
Windows Media Player 11 library through the AV
receiver.

Click “OK” to close the dialog box.
This completes the Windows Media Player 12
configuration.
You can now play the music files in your
Windows Media Player 12 library.

Tip
• Windows Media Player 11 can be downloaded for free
from the Microsoft web site.

■ Windows Media Player 12 Setup
This section explains how to configure Windows
Media Player 12 so that the AV receiver can play the
music files stored on your personal computer.

Start Windows Media Player 12.

Use q/w/e/r to select “DLNA”, and press
ENTER.

Use q/w to select a server, and then press
ENTER.
The menu is displayed according to the server
functions.

• If the media streaming is already activated, clicking on
“More streaming options...” in the “Stream” menu will
display a list of the playback devices connected to the
network. You can skip step 3.

On the “Library” menu, select “Media
Sharing”.
The “Media Sharing” dialog box appears.

Note
• The search function does not work with media servers
which do not support this function.
• Photos and movies stored on a media server cannot
be accessed from the AV receiver.
• Depending on the sharing settings in the media server,
the AV receiver may not able to access the content.
See the instruction manual of the media server.

Use q/w to select an item, and then press
ENTER or 1 to start playback.
dlna

My favorite song 1
0 :11 / 3:00
Artist name
My favorite album

Playing music files on a server (DLNA)

1
2

Start your computer or media server.
Note

En-35

• Depending on the media server, 5/4/3 may not
work.
• If the message “No Item.” appears, this means that no
information can be retrieved from the server. In this
case, check your server, network, and AV receiver
connections.

Playback
■ Creating a shared folder

Playing music files on a shared folder

Right-click the folder that you want to share.

In order to enjoy Home Media, you must first create a
shared folder on your computer.

Windows 8/Windows 7 Setup

1
2
3

■ Setting the sharing options

Check the check box of “Share this folder”
and then click “OK”.

Under “Network File and Folder Sharing”,
select “Share”.

Select “Everyone” from the pull-down menu,
click “Add”, and then click “Share”.

Playing Music Files on a Shared Folder
This section explains how to play music files on a
computer or NAS (Network Attached Storage)
through the AV receiver.

Select “Choose homegroup and sharing
options” on the Control Panel.
Tip
• If this option is not available, verify that “View by:” is set
to “Category”.

2
3

Select “Change advanced sharing settings”.
Under “Home or Work”, verify that the
following items are checked:
“Turn on network discovery”, “Turn on file and
printer sharing”, “Turn on sharing so anyone with
network access can read and write files in the
Public folders”, and “Turn off password protected
sharing”.

Select “Properties”.
On the “Sharing” tab, select “Advanced
Sharing”.

Tip
• The same operation can be done by selecting
“Network Service” in the Home menu.

Tip
• With this setting, everyone is allowed to access the
folder. If you want to assign a user name and
password to the folder, make the corresponding
settings for “Permissions” in “Advanced Sharing” of the
“Sharing” tab.
• Verify that “Workgroup” is properly set.

Use q/w/e/r to select “Home Media”, and
press ENTER.

Use q/w to select a server, and then press
ENTER.
Tip

Note
• When using NAS (Network Attached Storage), refer to
the instruction manual provided with your NAS unit.

Select “Save changes” and click “OK” on the
confirmation screen.

• The server name of your computer can be viewed on
the computer properties screen.

Use q/w to select the desired shared folder
and then press ENTER.

When asked for a user name and password,
enter the necessary login information.
Tip
• The login information will be remembered for the next
time you log in.
• The login information is that of the user account set
when creating a shared folder.

En-36

Use q/w to select a music file and then press
ENTER or 1.
The playback of the selected file starts.

Playback

Remote Playback

You need to connect the AV receiver to your home
network (➔ pages 16, 27).
Tip
• The on-screen menus appear only on a TV that is
connected to HDMI OUT MAIN.

Remote playback is supported by Windows Media
Player 12.
Remote Playback means you can play the music files
stored on a media server or personal computer with
the AV receiver by operating the controller device in
the home network.

Windows Media Player 12 Setup
This section explains how to configure Windows
Media Player 12 so that the AV receiver can play the
music files stored on your personal computer.

1
2

Using Remote Playback

1
2
3

Move your cursor and click on “Turn on media
streaming”.
A list of media server appears. Wording may vary
slightly depending on the network location.
On the “Media streaming options”, select the
AV receiver and confirm that it is set to
“Allowed”.

Turn on the AV receiver.
Start Windows Media Player 12.
To enable remote playback, you must first
configure Windows Media Player 12.
On Windows Media Player 12, right-click on a
music file.
The right-click menu appears.
Tip
• For selecting another media server, select the desired
media server from the “Other Libraries” menu on
Windows Media Player 12.

On the “Stream” menu, select “Turn on media
streaming”.
A dialog box appears.
• If the media streaming is already activated, clicking on
“More streaming options...” in the “Stream” menu will
display a list of the playback devices connected to the
network. You can skip step 3.

Tip
• On the “Stream” menu, confirm that “Allow remote
control of my Player...” is checked.

Start Windows Media Player 12.

Tip

Click “OK” to close the dialog box.
This completes the Windows Media Player 12
configuration.
You can now play the music files in your
Windows Media Player 12 library.

Select the AV receiver in “Remote playback”.
The “Play to” window appears and playback on
the AV receiver starts. Operations during remote
playback can be made from the “Play to” window
of Windows 8/Windows 7 on your personal
computer.
A playback screen will be displayed on the
connected TV.
Tip
• If the operating system of your personal computer is
Windows 8, click “Play to” and select the AV receiver.

En-37

Adjusting the Volume.
You can adjust the volume by adjusting the
volume bar in the “Remote playback” window.
The default maximum volume level is 64. If you
wish to change this, enter the value from the Web
Setup in your browser. Refer to step 3 of
“Registering Other Internet Radio” for details
(➔ page 34).
The volume value of the remote window and the
volume value of the AV receiver may not always
match.
Adjustments you make to the volume in the AV
receiver will not be reflected in the “Remote
playback” window.

Note
• Remote playback cannot be used in any of the following
cases:
– Network services are being used.
– Contents are being played from a USB device.
– “Agree” is not selected on the “DISCLAIMER” screen
displayed on the TV when you select the NET input
selector on the AV receiver for the first time.

Playback

Listening to AM/FM Radio

This section describes the procedure of using the
buttons on the front panel, unless otherwise specified.

Press TUNING q/w.
Searching stops when a station is found.
When tuned into a station, the TUNED indicator
lights. When tuned into a stereo FM station, the
FM STEREO indicator lights as shown.

Using the Tuner
With the built-in tuner you can enjoy AM and FM radio
stations. You can store your favorite stations as
presets for quick selection.
You can also change the frequency steps
(➔ page 64).

On the remote controller, press TUNER
repeatedly to select “AM” or “FM”, followed by
D.TUN.

TUNED
AUTO

(Actual display depends on the country.)
FM STEREO

Press TUNER to select either “AM” or “FM”.
In this example, FM has been selected.
Each time you press TUNER, the radio band
changes between AM and FM.
Band

■ Tuning into stations by frequency
You can tune into AM and FM stations directly by
entering the appropriate frequency.

Tip
• Tuning into weak FM stereo stations
If the signal from a stereo FM station is weak, it may
be impossible to get good reception. In this case,
switch to manual tuning mode and listen to the station
in mono.

Frequency

Within 8 seconds, use the number buttons to
enter the frequency of the radio station.
For example, to tune to 87.5 (FM), press 8, 7, 5
or 8, 7, 5, 0.
If you have entered the wrong number, you can
retry after 8 seconds.

Presetting AM/FM Stations
(Actual display depends on the country.)

Tuning into Radio Stations

■ Manual tuning mode
In manual tuning mode, FM stations will be in mono.

Press TUNING MODE so that the AUTO
indicator goes off on the AV receiver’s
display.

Press and hold TUNING q/w.
The frequency stops changing when you release
the button.
Press the buttons repeatedly to change the
frequency one step at a time.

■ Auto tuning mode

Press TUNING MODE so that the AUTO
indicator lights on the AV receiver’s display.

You can store a combination of up to 40 of your
favorite AM/FM radio stations as presets.

Tune into the AM/FM station that you want to
store as a preset.
See the previous section.

Press MEMORY.
The preset number flashes.

(Actual display depends on the country.)

En-38

While the preset number is flashing (about 8
seconds), use PRESET e/r to select a preset
from 1 through 40.

Playback

Press MEMORY again to store the station or
channel.
The station or channel is stored and the preset
number stops flashing.
Repeat this procedure for all of your favorite
AM/FM radio stations.

■ Selecting Presets

To select a preset, use PRESET e/r on the AV
receiver, or the remote controller’s CH +/–.
Tip
• You can also use the remote controller’s number
buttons to select a preset directly.

■ Deleting Presets

Select the preset that you want to delete.
See the previous section.

While holding down MEMORY, press TUNING
MODE.
The preset is deleted and its number disappears
from the AV receiver’s display.

Using RDS (excluding North American and
Taiwanese models)
When tuned into an RDS station, the RDS indicator
lights.
When the station is broadcasting text information, the
text can be displayed.

■ What is RDS?
RDS stands for Radio Data System and is a method
of transmitting data in FM radio signals. It was
developed by the European Broadcasting Union
(EBU) and is available in most European countries.
Many FM stations use it these days. In addition to
displaying text information, RDS can also help you
find radio stations by type (e.g., news, sport, rock,
etc.).
The AV receiver supports four types of RDS
information:
PS (Program Service)
When tuned to an RDS station that’s broadcasting PS
information, the station’s name will be displayed.
Pressing DISPLAY will display the frequency for 3
seconds.
RT (Radio Text)
When tuned to an RDS station that’s broadcasting
text information, the text will be shown on the AV
receiver’s display.
PTY (Program Type)
This allows you to search for RDS radio stations by
type.
TP (Traffic Program)
This allows you to search for RDS radio stations that
broadcast traffic information (➔ page 40).
Note
• RDS works only in areas where RDS broadcasts are
available.
• In some cases, the text characters displayed on the AV
receiver may not be identical to those broadcast by the
radio station. Also, unexpected characters may be
displayed when unsupported characters are received. This
is not a malfunction.
• If the signal from an RDS station is weak, RDS data may be
displayed intermittently or not at all.

En-39

■ Displaying Radio Text (RT)

Press RT/PTY/TP once.
The RT information scrolls across the AV
receiver’s display.
Note
• The message “Waiting” may appear while the AV
receiver waits for the RT information.
• If the message “No Text Data” appears, no RT
information is available.

■ Finding Stations by Type (PTY)
You can search for radio stations by type.

Press RT/PTY/TP twice.
The current program type appears on the AV
receiver’s display.

Use PRESET e/r to select the type of
program you want.
See the table shown later in this chapter.

To start the search, press ENTER.
The AV receiver searches until it finds a station of
the type you specified, at which point it stops
briefly before continuing with the search.

When a station you want to listen to is found,
press ENTER.
If no stations are found, the message “Not
Found” appears.

Playback
■ Listening to Traffic News (TP)

RDS program types (PTY)

You can search for stations that broadcast traffic
news.

Type

Display

None

News reports

News

Press RT/PTY/TP three times.
If the current radio station is broadcasting TP
(Traffic Program), “[TP]” will appear on the AV
receiver’s display. If “TP” without square brackets
appears, this means that the station is not
broadcasting TP.

Current affairs

Affairs

Information

Info

Sport

Culture

To locate a station that is broadcasting TP,
press ENTER.
The AV receiver searches until it finds a station
that’s broadcasting TP.
If no stations are found, the message “Not
Found” appears.

Science and technology

Science

Varied

Pop music

Pop M

Rock music

Rock M

Education

Educate

Drama

Middle of the road music

Easy M

Light classics

Light M

Serious classics

Classics

Other music

Other M

Weather

Finance

Children’s programmes

Children

Social affairs

Social

Religion

Phone in

Phone In

Travel

Leisure

Jazz music

Jazz

Country music

Country

National music

Nation M

Oldies music

Oldies

Folk music

Folk M

Documentary

Document

Alarm test

TEST

Alarm

Alarm!

En-40

Playing Audio and Video from Separate
Sources
You can listen to the audio of one input source while
watching the video of another. This function takes
advantage of the fact that when an audio-only input
source (PHONO, TV/CD, TUNER) is selected, the
video input source remains unchanged. The following
procedure shows how to listen to a CD player’s audio
source connected to TV/CD IN while watching a Bluray Disc/DVD player’s video source connected to
BD/DVD.
Tip
• To use an input selector as audio-exclusive, you must
assign all video inputs to “- - - - -” ( ➔ page 54).

1
2

Press BD/DVD.

Start playback on your Blu-ray Disc/DVD and
CD players.
You can now enjoy watching your Blu-ray
Disc/DVD with the sound of your CD player.

Press TV/CD.
The audio output changes to the CD source, but
the video of previously-selected BD/DVD is
retained.

Playback
(North American and Taiwanese models)

Using the Listening Modes
About Listening Modes
The AV receiver’s listening modes can transform your
listening room into a movie theater or concert hall,
with high fidelity and stunning surround sound.

Selecting Listening Modes
MOVIE/TV, MUSIC, GAME

Note

■ Listening Mode Buttons
(European, Australian and Asian models)

Press RECEIVER first.

PURE AUDIO MOVIE/TV, MUSIC, GAME

MUSIC
MOVIE/TV

PURE AUDIO button and indicator
(European, Australian and Asian models)
This button selects the Pure Audio listening mode.
When this mode is selected, the AV receiver’s display
and analog video circuitry are turned off. Only video
signals input through HDMI input can be output from
the HDMI output. The indicator lights when this mode
is selected. Pressing this button again will select the
previous listening mode.

GAME
STEREO

MOVIE/TV button
This button selects the listening modes intended for
use with movies and TV.
MUSIC button
This button selects the listening modes intended for
use with music.
GAME button
This button selects the listening modes intended for
use with video games.
STEREO button
This button selects the Stereo listening mode and All
Channel Stereo listening mode.

En-41

• The Dolby Digital and DTS listening modes can only be
selected if your Blu-ray Disc/DVD player is connected to the
AV receiver with a digital audio connection (coaxial, optical,
or HDMI).
• The listening modes you can select depends on the format
of the input signal. To check the format, see “Displaying
Source Information” (➔ page 45).
• While a pair of headphones is connected, you can select
the following listening modes: Pure Audio (European,
Australian and Asian models), Mono, Direct, and Stereo.

Playback
■ Onkyo-Original DSP Listening Modes

Input Source
The following audio formats are supported by the listening modes.
A

This is mono (monophonic) sound.

This is stereo (stereophonic) sound. Two independent audio signal channels
are reproduced through two speakers.

Listening Mode

Description

Orchestra

Suitable for classical or operatic music,
this mode emphasizes the surround
channels in order to widen the stereo
image, and simulates the natural
reverberation of a large hall.

Or ches t r a

This is 5.1-channel surround sound. This surround system has five main
channels of sound and a sixth subwoofer channel (called the point-one
channel).

This is 7.1-channel surround sound. This is a further sound enhancement to
5.1-channel sound with two additional speakers that provide greater sound
envelopment and more accurate positioning of sounds.

This is DTS-ES surround sound. This surround system can produce a discrete
or a matrix-encoded sixth channel from existing DTS 5.1 encoded material.

Studio-Mix

This is Dolby Digital EX surround sound. This provides a center back surround
channel from 5.1-channel sources.

S t u d i o –M i x

Unplugged
Un p l u g g e d

Speaker Layout
The illustration shows which speakers are activated in each channel. See
“Speaker Configuration” for the speaker setup (➔ page 55).

TV Logic

Game-RPG

Log i c

G ame – RPG

Game-Action
G ame – A c t i o n

Game-Rock

G ame – R o c k

Game-Sports
G ame – S p o r t s

All Ch Stereo
A l l

S t e r eo

Full Mono
Fu l l

En-42

Mo n o

Input
Source

Speaker
Layout

A CN
S
D
F
G
Suitable for acoustic instruments, vocals H
and jazz, this mode emphasizes the
front stereo image, giving the impression
of being right in front of the stage.
Suitable for rock or pop music, listening
to music in this mode creates a lively
sound field with a powerful acoustic
image, like being at a club or rock
concert.
This mode adds realistic acoustics to TV
shows produced in a TV studio,
surround effects to the entire sound, and
clarity to voices.
In this mode, the sound has a dramatic
feel with a similar atmosphere to
Orchestra mode.
In this mode, sound localization is
distinct with emphasis on bass.
In this mode, sound pressure is
emphasized to heighten live feel.
Suitable for audio source with much
reverberation.
Ideal for background music, this mode
fills the entire listening area with stereo
sound from the front, surround, and
surround back speakers.
In this mode, all speakers output the
same sound in mono, so the sound you
hear is the same regardless of where
you are within the listening room.

XCN

Playback
Listening Mode

Description

Input
Source

T-D (TheaterDimensional)

With this mode you can enjoy a virtual
surround sound even with only two or
three speakers. This works by
controlling how sounds reach the
listener’s left and right ears. Good
results may not be possible if there’s too
much reverb, so we recommend that
you use this mode in an environment
with little or no natural reverb.

A ZXC
S N
D
F
G
H

T–D

Speaker
Layout

Pure Audio*1*2
Pu r eAAu d i o

Direct
D i r ec t

Stereo
S t e r eo

Mono
Mo n o

Multichannel
Mu l t i c h

Description

DSD*4

In this mode, audio from the input source D XCN
is output without surround-sound
processing. The speaker configuration
(presence of speakers), crossover
frequency, speaker distance, A/V Sync
and much of the processing set via the
D XCN
audio setup are enabled. See “Onscreen Setup” for more details
F XCN*3
(➔ page 48).

DSD

Dolby Digital
Do l b y

Do l b y

Description
In this mode, the display and video
circuitry are turned off, minimizing
possible noise sources for the ultimate in
high-fidelity audio reproduction. (As the
analog video circuitry is turned off, only
video signals input through HDMI IN can
be output from the HDMI output.)

Input
Source

Speaker
Layout

A ZXC
S N*3
D
F
G
H

Speaker
Layout

T r u e HD

DTS

D XCN

DTS

DTS-HD High
Resolution Audio
D T S – HD

D XCN
F XCN*3

DTS-HD Master
Audio

DTS Express
DTS

DTS

96 / 24

ZXC
N
DTS-ES Discrete*7
ES

D XCN
F

En-43

D XCN

Exp r ess

DTS 96/24*6

Use this mode when watching an old
movie with a mono soundtrack, or use it
with the foreign language soundtracks
recorded in the left and right channels of
some movies. It can also be used with
DVDs or other sources containing
multiplexed audio, such as karaoke
DVDs.
This mode is for use with PCM
multichannel sources.

Input
Source

D T S – HD MS T R

In this mode, audio from the input source
is output without surround-sound
processing. The speaker configuration
(presence of speakers) and speaker
distance settings are enabled, but much
of the processing set via the audio setup
is disabled. See “On-screen Setup” for
more details (➔ page 48).
Sound is output from the front left and
right speakers and subwoofer.

Dolby Digital Plus*5

Dolby TrueHD

■ Listening Modes
Listening Mode

Listening Mode

D i sc r e t e

This mode is for use with DTS 96/24
sources. This is high-resolution DTS
with a 96 kHz sampling rate and 24-bit
resolution, providing superior fidelity.
Use it with DVDs that bear the DTS
96/24 logo.

D XCN

This mode is for use with DTS-ES
Discrete soundtracks, which use a
discrete surround back channel for true
6.1/7.1-channel playback. The seven
totally separate audio channels provide
better spatial imaging and 360-degree
sound localization, perfect for sounds
that pan across the surround channels.
Use it with DVDs that bear the DTS-ES
logo, especially those with a DTS-ES
Discrete soundtrack.

G V

Playback
Listening Mode

Description

DTS-ES Matrix*7

This mode is for use with DTS-ES Matrix G V
soundtracks, which use a matrixencoded back-channel for 6.1/7.1channel playback. Use it with DVDs that
bear the DTS-ES logo, especially those
with a DTS-ES Matrix soundtrack.

ES Ma t r i x

Input
Source

Speaker
Layout

Dolby Pro Logic IIx*8 Dolby Pro Logic IIx expands any 2channel source for 7.1-channel
Dolby Pro Logic II
playback. It provides a very natural and
PL
Mo v i e
seamless surround-sound experience
that fully envelops the listener. As well
PL
Mu s i c
as music and movies, video games can
also benefit from the dramatic spatial
PL
Game
effects and vivid imaging.
PL

Mo v i e

Mu s i c

Game

If you’re not using any surround back
S XCN
speakers, Dolby Pro Logic II will be
used instead of Dolby Pro Logic IIx.
• Dolby PLIIx Movie
Use this mode with any stereo or Dolby
Surround (Pro Logic) movie (e.g., TV,
DVD, VHS).
• Dolby PLIIx Music
Use this mode with any stereo or Dolby
Surround (Pro Logic) music source
(e.g., CD, radio, cassette, TV, VHS,
DVD).
• Dolby PLIIx Game
Use this mode with video games,
especially those that bear the Dolby
Pro Logic II logo.
• Dolby PLIIx Movie
D V
• Dolby PLIIx Music
These modes use the Dolby Pro Logic
IIx modes to expand 5.1-channel
sources for 7.1-channel playback.

Listening Mode

Description

Input
Source

Dolby Pro Logic IIz
Height

Dolby Pro Logic IIz Height is designed
to more effectively use existing program
material when height channel speaker
outputs are present. Dolby Pro Logic
IIz Height can be used to upmix a
variety of sources from movies and
music, but are particularly well-suited to
upmix game content.

S B
D
F
G
H

These modes expand 5.1-channel
sources for 6.1/7.1-channel playback.
They’re especially suited to Dolby EX
soundtracks that include a matrixencoded surround back channel. The
additional channel adds an extra
dimension and provides an enveloping
surround sound experience, perfect for
rotating and fly-by sound effects.

D V
H

He i g h t

Dolby EX
Do l b y

Do l b y

DTS Neo:6

Ne o : 6

C i n ema

Ne o : 6

Mu s i c

Ne o : 6

En-44

Speaker
Layout

This mode expands any 2-channel
source for up to 7.1-channel playback. It
uses seven full-bandwidth channels of
matrix decoding for matrix-encoded
material, providing a very natural and
seamless surround sound experience
that fully envelops the listener.
• DTS Neo:6 Cinema
Use this mode with any stereo movie
(e.g., TV, DVD, VHS).
• DTS Neo:6 Music
Use this mode with any stereo music
source (e.g., CD, radio, cassette, TV,
VHS, DVD).

S XCN

• DTS Neo:6
D V
This mode uses DTS Neo:6 to expand
5.1-channel sources for 6.1/7.1channel playback.

Playback
Note
*1
*2

*5
*6
*7
*8

(North American and Taiwanese models) This
listening mode is not available.
Pure Audio cannot be selected when Zone 2 is active.
Besides, if you activate Zone 2 while Pure Audio is
selected, the listening mode will automatically switch to
Direct.
Based on the audio channel signal contained in the
source, the corresponding speakers will output the
sound.
The AV receiver can input the DSD signal from HDMI IN.
Depending on the player, setting the output on the player
side to PCM might bring better sound.
For the Blu-ray Discs, Dolby Digital is used in a 3.1/5.1channel speaker system.
DTS is used depending on the configuration of the AV
receiver.
If there are no surround back speakers, DTS is used.
If there are no surround back speakers, Dolby Pro Logic
II is used.

Displaying Source Information

Using the Sleep Timer

You can display various information about the current
input source as follows.

With the sleep timer, you can set the AV receiver to
turn off automatically after a specified period.

Press RECEIVER once followed by DISPLAY
repeatedly to cycle through the available
information.
Tip
• Alternatively, you can use DISPLAY on the AV
receiver.

The following information can be typically displayed.

Press RECEIVER once followed by SLEEP
repeatedly to select the required sleep time.
The sleep time can be set from 90 to 10 minutes
in 10 minute steps.
The SLEEP indicator lights on the AV receiver’s
display when the sleep timer has been set. The
specified sleep time appears for about 5
seconds, then the previous display reappears.
Tip

Input source &
volume*1

• If you need to cancel the sleep timer, press SLEEP
repeatedly until the SLEEP indicator goes off.
• To check the time remaining until the AV receiver
sleeps, press SLEEP. Note that if you press again on
SLEEP as the time being displayed is 10 minutes or
less, the sleep timer will go off.

Listening mode

The listening mode may not be selected depending
on the input signal. The signal input from the
external AV components can be displayed by the
function as follows.

Signal format*2
Sampling
frequency*2

Input signal
resolution
Output resolution

*1
*2

When AM or FM radio is used, the band, preset number,
and frequency are displayed.
If the input signal is digital, the signal format is displayed.
Information is displayed for about three seconds, then
the previously displayed information reappears.

En-45

Playback

Setting the Display Brightness

Muting the AV Receiver

You can adjust the brightness of the AV receiver’s
display.

You can temporarily mute the output of the AV
receiver.

Press RECEIVER once followed by DIMMER
repeatedly to switch between: normal, dim, or
dimmer brightness.
Tip

Press RECEIVER followed by MUTING.
The output is muted and the MUTING indicator
flashes on the AV receiver’s display.
Tip

• (North American and Taiwanese models)
Alternatively, you can use DIMMER on the AV
receiver.

• To unmute, press MUTING again or adjust the volume.
• Muting is automatically cancelled when the AV
receiver is set to standby.

Changing the Input Display
When you connect an u-capable Onkyo
component, you must configure the input display so
that u can work properly.
This setting can be done only from the front panel.

Press TV/CD or GAME.
“TV/CD” or “GAME” appears on the AV receiver’s
display.

Press and hold down the same button (about
3 seconds) to change the input display.
Repeat this step to select the desired input
display.
TV/CD → DOCK
TAPE

■ GAME:

GAME ↔ DOCK

→

■ TV/CD:

“

Note
• “DOCK” can be selected for the “TV/CD” or “GAME”
input selector, but not at the same time.
• Enter the appropriate remote control code before using
the remote controller for the first time (➔ page 72).

En-46

Playback

Using the Home Menu
The Home menu provides quick access to frequently
used menus.
Tip
• The on-screen menus appear only on a TV that is
connected to HDMI OUT MAIN.

Press RECEIVER followed by HOME.
The Home menu will be superimposed on the TV
screen.
Tip
• Alternatively, you can use HOME on the AV receiver.

connected through HDMI, you can easily switch
between inputs as their previews are displayed on
a single screen.
Press ENTER to display the main preview
(currently selected HDMI input) and the
additional previews (other HDMI inputs). Using
q/w or e/r to select a preview thumbnail and
pressing ENTER will switch the AV receiver to
that input source.
Tip
• If no video signals are present, the thumbnails will be
filled in black.
• You can specify the number of preview thumbnails as
well as their positioning on screen (➔ page 66).
Note
• This function cannot be selected when:
– HDMI IN 6 is the current HDMI input source, or
– No signal is present on the current input source.
• Depending on video signals, the picture may not be
properly rendered on the preview thumbnails of
InstaPrevue.

Use e/r or q/w and ENTER to make the
desired selection.
Press HOME to close the menu.

■ Setup
` With this selection, you can access the common
settings of the on-screen Setup menu.
Press ENTER to display the Setup menu
(➔ page 52).
Tip
• You can also access frequently used settings from Quick
Setup (➔ page 48).

■ InstaPrevue
` With this selection, you can preview audio/video
streams coming from HDMI inputs (HDMI
IN 1/2/3/4/5). Even with multiple components

■ Firmware Update
` With this selection, you can update the firmware
of the AV receiver. Note that this selection will be
grayed out for a short while after the AV receiver
is turned on. Please wait until it becomes
operable.
Press ENTER to start the procedure
(➔ page 85).
■ Network Service
You need to connect the AV receiver to your home
network (➔ page 16, 27).
` With this selection, you can use various Internet
radio services or play the contents stored in media
connected to your home network (➔ pages 32 to
36). Note that this selection will be grayed out for

En-47

a short while after the AV receiver is turned on.
Please wait until it becomes operable.
Press ENTER to display the network service
screen. If you want to use the Internet radio
services, use q/w/e/r to select the desired
service. Pressing ENTER again switches to that
selection. If you want to play music files on a
computer or media server, use q/w/e/r to
select “DLNA” and then press ENTER. If you
want to play music files on a computer or NAS
(Network Attached Storage), use q/w/e/r to
select “Home Media” and then press ENTER.
■ USB
`With this selection, you can play contents of
portable players and USB storage devices
connected to the AV receiver’s USB port
(➔ page 32). Note that this selection will be
grayed out for a short while after the AV receiver
is turned on. Please wait until it becomes
operable.
Press ENTER to select a drive or browse the
contents of the media connected, followed by
q/w to select the desired folder or track.
Pressing ENTER as a track is selected will start
playback.

Advanced Operations
In addition, previews of the video streams coming
from HDMI inputs (HDMI IN 1/2/3/4/5) are
displayed.*2
Use q/w to select an input source and view the
related information. Pressing ENTER switches to
the selected input source.

Using the Quick Setup

Advanced Operations

■ Audio (➔ page 49)
`You can change the following settings: “Bass”,
“Treble”, “Phase Matching Bass”, “Subwoofer
Level”, “Center Level”, “Audyssey”,
“Dynamic EQ”, “Dynamic Volume”, “Late
Night”, “Music Optimizer” and “Cinema Filter”.

RECEIVER

ENTER,
q/w/e/r

On-screen Setup

RETURN

Q SETUP

This section describes the procedure for using the
remote controller unless otherwise specified.
With the AV receiver connected to a TV, there are two
ways of changing the settings on-screen: using the
Quick Setup or the Setup Menu (HOME).

■ Quick Setup
The Quick Setup provides quick access to frequently
used settings. You can change settings and view the
current information.
■ Setup menu (HOME)
The Setup menu (HOME) provides a convenient way
to change the AV receiver’s various settings. Settings
are organized into 9 categories.
Tip

• The on-screen menus appear only on a TV that is
connected to HDMI OUT MAIN.

Press RECEIVER followed by Q SETUP.
The Quick Setup will be superimposed on the TV
screen.

BD/DVD
Input
Audio
Video
Information
Listening Mode

Use q/w and ENTER to make the desired
selection.
Press Q SETUP to close the menu.
Press RETURN to return to the previous menu.

■ Input*1
` You can select input sources and view the
following information: the name of input selectors,
input assignments, the name of the device paired
with the AV receiver via Bluetooth, radio
information, and ARC function setting.

En-48

■ Video*3
`You can change the following settings: “Wide
Mode” and “Picture Mode*4”.
See also:
• “Picture Adjust” (➔ page 61)
■ Information*5
`You can view the information of the following
items: “Audio”, “Video” and “Tuner”.
■ Listening Mode*6
`You can select the listening modes that are
grouped in the following categories: “MOVIE/TV”,
“MUSIC”, “GAME”.
Use q/w to select the category and e/r to
select the listening mode. Press ENTER to
switch to the selected listening mode.
Note
*1
*2

“BLUETOOTH” cannot be selected, if you’ve selected
NET or USB as input selector in Zone 2.
• The video preview is not displayed when:
–HDMI IN 6 is the current HDMI input source, or
–No signal is present on the current input source.
• The video of the currently-selected input is displayed on
the main screen, not on a preview thumbnail.
• When the “Monitor Out” setting is set to “Sub”, “Video”
cannot be selected (➔ page 53).

Advanced Operations

*5
*6

• This setting cannot be used with the NET, USB and
BLUETOOTH input selectors.
Only when you have selected “Custom” in the “Picture
Mode” (➔ page 61), pressing ENTER allows you to
adjust the following items via the Quick Setup:
“Brightness”, “Contrast”, “Hue” and “Saturation”. Press
RETURN to return to the “Picture Mode” setting.
Depending on the input source and listening mode, not
all channels shown here output the sound.
• This setting is not available in either of the following
cases:
–The “Audio TV Out (Main)” setting is set to “On”
(➔ page 65) or “Audio TV Out (Sub)” setting is set to
“On” (➔ page 65) and you’re listening through your TV
speakers.
–“HDMI CEC (RIHD)” is set to “On” (➔ page 64) and
you’re listening through your TV speakers.

Explanatory Notes
a
b

■ Phase Matching Bass
`Off
`On

a Setting target
b Setting options (default setting underlined)

Using the Audio Settings of Quick
Setup
You can change various audio settings from the
Quick Setup (➔ page 48).
Note
• These settings are not available in either of the following
cases:
– The “Audio TV Out (Main)” setting is set to “On”
(➔ page 65) or “Audio TV Out (Sub)” setting is set to
“On” (➔ page 65) and you’re listening through your TV
speakers.
– “HDMI CEC (RIHD)” is set to “On” (➔ page 64) and
you’re listening through your TV speakers.

Tone Control
■ Bass
` –10dB to 0dB to +10dB in 2 dB steps.
You can boost or cut low-frequency sounds
output from the front speakers.
■ Treble
` –10dB to 0dB to +10dB in 2 dB steps.
You can boost or cut high-frequency sounds
output from the front speakers.
You can adjust the bass and treble for the front
speakers, except when Direct or Pure Audio
(European, Australian and Asian models) listening
mode is selected.

Phase Matching Bass
■ Phase Matching Bass
`Off
`On
From the warm low notes produced by a cello to the
deep frequencies of electronic music, a good audio
system should be able to deliver plenty of bass
resonance.
While traditional enhancement systems effectively
boost low-frequency sound, they are often prone to
the effects of phase shifting, which can overwhelm
mid-range frequencies and muddy the sound. Our
Phase-Matching Bass Boost technology effectively
preserves mid-range clarity-allowing vocals and
strings to shine-while maintaining a smooth, powerful
bass response at all volume levels.
Note
• The Phase Matching Bass is disabled when the Direct or
Pure Audio (European, Australian and Asian models)
listening mode is selected.
• If the “Subwoofer” setting is set to “No”, this setting is fixed
to “Off”.

Operating on the AV receiver

1
2

Press TONE repeatedly to select “PM Bass”.
Use – and + to change the setting.

Operating on the AV receiver

Press TONE repeatedly to select either “Bass”
or “Treble”.

Use – and + to adjust.

En-49

Operating
procedure
(➔ page 48)

Advanced Operations

Speaker Levels

• The setting is stored individually for each input selector.

Music Optimizer

■ Subwoofer Level
` –15dB to 0dB to +12dB in 1 dB steps.

Late Night

■ Music Optimizer
`Off
`On
The Music Optimizer function enhances the sound
quality of compressed music files. When set to “On”,
the M.Opt indicator lights on the AV receiver’s
display.

■ Center Level
` –12dB to 0dB to +12dB in 1 dB steps.
You can adjust the volume of each speaker while
listening to an input source.
These temporary adjustments are cancelled when the
AV receiver is set to standby. To save the setting you
made here, go to “Level Calibration” (➔ page 57)
before setting the AV receiver to standby.
Note
• You cannot use these function while the AV receiver is
muted.
• These settings cannot be used while a pair of headphones
is connected.
• Speakers that are set to “No” or “None” in
“Speaker Configuration” (➔ page 55) cannot be adjusted.

Audyssey®
■ Audyssey
See “Audyssey” in “4. Source Setup” (➔ page 58).
■ Dynamic EQ
See “Dynamic EQ” in “4. Source Setup” (➔ page 59).
■ Dynamic Volume
See “Dynamic Volume” in “4. Source Setup”
(➔ page 59).
Note
• These technologies can be used when all the following
conditions are met:
– Room Correction and Speaker Setup is completed. Note
that “Audyssey” requires the “Audyssey MultEQ Full
Calibration” method.
– Any listening mode other than Direct or Pure Audio
(European, Australian and Asian models) is selected.
– A pair of headphones is not connected.

■ Late Night
For Dolby Digital and Dolby Digital Plus sources,
the options are:
` Off
` Low:
Small reduction in dynamic range.
` High:
Large reduction in dynamic range.
For Dolby TrueHD sources, the options are:
` Auto:
The Late Night function is set to “On” or “Off”
automatically.
` Off
` On
Turn this setting on to reduce the dynamic range of
Dolby Digital material so that you can still hear quiet
parts even when listening at low volume levels—ideal
for watching movies late at night when you don’t want
to disturb anyone.
Note

Tip
• (North American and Taiwanese models) Alternatively,
you can use MUSIC OPTIMIZER on the AV receiver.
Note
• The Music Optimizer function only works with PCM digital
audio input signals with a sampling rate below 48 kHz and
analog audio input signals.
When NET or USB input selector is selected, this function
even works with digital audio input signals with a sampling
rate below 48 kHz (except DSD signals and Dolby TrueHD
signals) regardless of the PCM digital audio input signals
with a sampling rate below 48 kHz.
• The Music Optimizer is disabled when the Direct or Pure
Audio (European, Australian and Asian models)
listening mode is selected.
• The setting is stored individually for each input selector.

• The effect of the Late Night function depends on the
material that you are playing and the intention of the original
sound designer, and with some material there will be little
or no effect when you select the different options.
• The Late Night function can be used only when the input
source is Dolby Digital, Dolby Digital Plus, or Dolby
TrueHD.
• The Late Night function is set to “Off” when the AV receiver
is set to standby. For Dolby TrueHD sources, it will be set
to “Auto”.
• With Dolby TrueHD sources, the Late Night function cannot
be used when “TrueHD Loudness Management” is set to
“Off”.

En-50

Operating
procedure
(➔ page 48)

Advanced Operations

CinemaFILTER
■ Cinema Filter
` Off
` On
Turn this setting on to soften overly bright movie
soundtracks, which are typically mixed for
reproduction in a movie theater.
CinemaFILTER can be used with the following
listening modes: Dolby Digital, Dolby Digital EX,
Dolby Digital Plus, Dolby TrueHD, Dolby Pro Logic IIx
Movie, Dolby Pro Logic II Movie, Dolby Pro Logic IIz
Height, Multichannel, DTS, DTS-ES, DTS Neo:6
Cinema, DTS 96/24, DTS Neo:6, DTS-HD High
Resolution Audio, DTS-HD Master Audio and DTS
Express.
Note
• The CinemaFILTER may not work when used with certain
input sources.

En-51

Operating
procedure
(➔ page 48)

Advanced Operations

Using the Setup Menu (HOME)
Remote
indicator

Setup Menu Items

Main menu item

Sub menu item

7. Hardware Setup
(➔ page 64)

Tuner

Sub menu item
Monitor Out

Auto Standby

HDMI Input

Network
Initial Setup

Component Video Input

RECEIVER

Digital Audio Input
2. Speaker Setup
(➔ page 55)

Speaker Settings
Speaker Configuration
Speaker Distance

ENTER,
q/w/e/r

Level Calibration

RETURN

3. Audio Adjust
(➔ page 57)

Multiplex/Mono
Dolby
DTS

HOME

Theater-Dimensional

1
2
3

Press RECEIVER followed by HOME.

4. Source Setup
(➔ page 58)

Audyssey
IntelliVolume

Use e/r or q/w to select “Setup”, and then
press ENTER.

A/V Sync

Use q/w to select a main menu item, and then
press ENTER.

Picture Adjust

Use q/w to select a sub menu item, and then
press ENTER.

Use q/w to select a setting target, and use e/r
to change the setting.
Press HOME to close the menu.
Press RETURN to return to the previous menu.

Name Edit
Audio Selector
5. Listening Mode Preset BD/DVD
(➔ page 63)
CBL/SAT
GAME
PC
AUX
TUNER
TV/CD
PHONO

Note
• This procedure can also be performed on the AV receiver
by using HOME, the cursor buttons, and ENTER.
• During Audyssey MultEQ® Room Correction and Speaker
Setup, messages, etc., that are displayed on the TV screen
will appear on the AV receiver’s display.

HDMI

Main menu item
1. Input/Output Assign
(➔ page 53)

NET
USB
BLUETOOTH
6. Miscellaneous
(➔ page 63)

Volume Setup
OSD Setup

En-52

8. Remote Controller
Setup
(➔ page 68)

Remote ID

9. Lock Setup
(➔ page 68)

Setup

Remote Mode Setup

Advanced Operations

Explanatory Notes
a

1. Input/Output Assign

2. Speaker Setup

Note
• The “HDMI Through” setting is only available for the HDMI
OUT MAIN jack (➔ page 65).

Monitor Out

Speaker Configuration

c
d

■ Subwoofer
`Yes
`No

a Main Menu
b Sub Menu
c Setting target
d Setting options (default setting underlined)

On the “Monitor Out” settings, you can select
whether or not to have the video sources’ images
output through the HDMI output.
If you connect your TV to HDMI output, “Monitor Out”
setting is automatically set and composite video and
component video sources are upconverted* and
output.
Composite video,
component video

HDMI

OUT
Composite video,
component video

HDMI

Note
Sub Menu
Main Menu

• See “The video and audio signal flow” (➔ page 17) for
charts showing how the “Monitor Out” and “Resolution”
settings affect the video signal flow through the AV
receiver.

■ Monitor Out
` Main:
Select this if your TV is connected to HDMI OUT
MAIN.
` Sub:
Select this if your TV is connected to HDMI OUT
SUB.
` Both:
Select this if your TVs are connected to HDMI
OUT MAIN and HDMI OUT SUB. Video signals
are output from both HDMI outputs at the
resolution supported by both TVs.

En-53

■ Resolution
`Through:
Select this to pass video through the AV receiver
at the same resolution and with no conversion.
`Auto:
Select this to have the AV receiver automatically
convert video at resolutions supported by your
TV.
`480p (480p/576p), 720p, 1080i, 1080p*1:
Select the desired output resolution.
`4K:
Select this for an output resolution four times
that of 1080p. Depending on the resolution
supported by your TV, it will result in either 3840
× 2160 or 4096 × 2160 pixels.
You can specify the output resolution for HDMI OUT
MAIN and have the AV receiver upconvert the picture
resolution as necessary to match the resolution
supported by your TV.
Tip
• You can see the picture by pressing ENTER to check the
“Resolution” setting for HDMI OUT MAIN (excluding NET,
USB and BLUETOOTH input source).
Note
• With some TVs, video signals are processed in the same
way as “Through” when this setting is set to “4K”.
• If the “Monitor Out” setting is set to “Sub”, this setting is
fixed to “Through”.
• If the “Monitor Out” setting is set to “Both”, this setting is
fixed to “Auto”.
*1 When signal is 1080p input at 24 frames per second, it
will be 1080p output at 24 frames per second.

Operating
procedure
(➔ page 52)

Advanced Operations

HDMI Input
If you connect a video component to an HDMI input,
you must assign that input to an input selector. For
example, if you connect your Blu-ray Disc/DVD player
to HDMI IN 1, you must assign “HDMI1/MHL” to the
“BD/DVD” input selector.
If you’ve connected your TV to the AV receiver with
an HDMI cable, composite video and component
video sources can be upconverted* and output by the
HDMI output. You can set this for each input selector
by selecting the “- - - - -” option. See “The video and
audio signal flow” for more information on video
signal flow and upconversion (➔ page 17).
Composite video,
component video

HDMI

■ BD/DVD, CBL/SAT, GAME, PC, AUX, TV/CD,
PHONO
` HDMI1/MHL, HDMI2, HDMI3, HDMI4, HDMI5,
HDMI6:
Select the input to which the component has
been connected.
` - - - - -:
Output composite video and component video
sources from the HDMI output. The video output
signal from the HDMI output is the one
configured in “Component Video Input”.
Each HDMI input cannot be assigned to two input
selectors or more. When HDMI1 - HDMI6 have
already been assigned, you must first set any
unused input selectors to “- - - - -” or you will be
unable to assign HDMI1 - HDMI6 to other input
selectors.
Note

OUT
Composite video,
component video

HDMI

Here are the default assignments.
Input selector

Default assignment

BD/DVD

HDMI2

CBL/SAT

HDMI3

GAME

HDMI4

HDMI5

AUX

HDMI1/MHL

TV/CD

-----

PHONO

-----

• If no video component is connected to the HDMI input (even
if the HDMI input is assigned), the AV receiver selects the
video source based on the setting of “Component Video
Input”.
• When an HDMI IN is assigned to an input selector as
explained here, the same HDMI IN will be set as a priority
in the “Digital Audio Input”. In this case, if you want to use
the coaxial or optical audio input, make the appropriate
selection in the “Audio Selector” setting (➔ page 62).
• Do not assign an HDMI IN to the TV/CD selector while
“HDMI CEC (RIHD)” is set to “On” (➔ page 64), otherwise
appropriate CEC (Consumer Electronics Control) operation
will not be guaranteed.
• If you assign “- - - - -” to an input selector that is currently
selected in “HDMI Through” (➔ page 65), the “HDMI
Through” setting will be automatically switched to “Off”.
• In order for the AV receiver to upconvert component input
to HDMI output, the source output must be set to 480i/576i.
When signal is input at resolution of 480p/576p and more,
error message will be displayed.

En-54

Component Video Input
If you connect a video component to a component
video input, you must assign that input to an input
selector. For example, if you connect your Blu-ray
Disc/DVD player to COMPONENT VIDEO IN, you
must assign “IN1” to the “BD/DVD” input selector.
Here are the default assignments.
Input selector

Default assignment

BD/DVD

-----

CBL/SAT

IN1

GAME

-----

AUX

-----

TV/CD

-----

PHONO

-----

■ BD/DVD, CBL/SAT, GAME, PC, AUX, TV/CD,
PHONO
`IN1:
Select the input to which the component has
been connected.
`- - - - -:
Output composite video sources from the HDMI
output.
Note
• When composite video and component video sources are
upconverted for HDMI OUT SUB, only signals with a
resolution of 480i/576i are output and the resolution
remains the same. If your TV doesn’t support this
resolution, there will be no picture (➔ page 84).

Operating
procedure
(➔ page 52)

Advanced Operations

Digital Audio Input

2. Speaker Setup

If you connect a component to a digital audio input,
you must assign that input to an input selector. For
example, if you connect your CD player to the
COAXIAL IN 1, you must assign “COAXIAL1” to the
“TV/CD” input selector.
Here are the default assignments.
Input selector

Default assignment

BD/DVD

COAXIAL1

CBL/SAT

COAXIAL2

GAME

-----

AUX

-----

TV/CD

OPTICAL

PHONO

-----

■ BD/DVD, CBL/SAT, GAME, PC, AUX, TV/CD,
PHONO
` COAXIAL1, COAXIAL2, OPTICAL:
Select the input to which the component has
been connected.
` - - - - -:
Select if the component is connected to an
analog audio input.
Note
• When an HDMI IN is assigned to an input selector in
“HDMI Input” (➔ page 54), the same HDMI IN will be set
as a priority in this assignment. In this case, if you want to
use the coaxial or optical audio input, make the appropriate
selection in the “Audio Selector” (➔ page 62).
• Supported sampling rates for PCM signals (stereo/mono)
from a digital input (optical and coaxial) are
32/44.1/48/88.2/96 kHz/16, 20, 24 bit.

Here you can check the settings made by
Audyssey MultEQ® Room Correction and Speaker
Setup function, or set them manually, which is useful
if you change one of the connected speakers after
using Audyssey MultEQ Room Correction and
Speaker Setup function (➔ page 24).
Note
• These settings are not available in either of the following
cases:
– a pair of headphones is connected.
– The “Audio TV Out (Main)” setting is set to “On”
(➔ page 65) or “Audio TV Out (Sub)” setting is set to
“On” (➔ page 65) and you’re listening through your TV
speakers.
– “HDMI CEC (RIHD)” is set to “On” (➔ page 64) and
you’re listening through your TV speakers.

Speaker Settings

`6ohms:
Select if the impedances of all speakers are
between 6 and 16 ohms.
Note
• (North American and Taiwanese models) Speakers with
an impedance of less than 6 ohms are not supported.

■ Speakers Type (Front)
`Normal:
Select this if you’ve connected your front
speakers normally.
`Bi-Amp:
Select this if you’ve bi-amped your front
speakers.
■ Powered Zone 2
`No
`Yes:
Zone 2 speakers can be used (Powered Zone 2
enabled).
Note

If you change these settings, you must run
Audyssey MultEQ Room Correction and Speaker
Setup again (➔ page 24).
If you bi-amp the front speakers, you must change the
“Speakers Type (Front)” setting. For details on
speaker wire connection, see “Bi-amping the Front
Speakers” (➔ page 14).
Note
• When bi-amping is used, the AV receiver is able to drive up
to 5.1 speakers in the main room.
• Before you change these settings, turn down the volume.

■ Speaker Impedance
(European, Australian and Asian models)
` 4ohms:
Select if the impedance of any speaker is 4
ohms or more but less than 6.

En-55

• If the “Speakers Type (Front)” setting is set to “Bi-Amp”,
Powered Zone 2 cannot be used.
• When the “Powered Zone 2” setting is set to “Yes” and
Zone 2 is turned on, the surround back and front high
speakers cannot be used.

Speaker Configuration
This setting is set automatically by
Audyssey MultEQ Room Correction and Speaker
Setup function (➔ page 24).
With these settings, you can specify which speakers
are connected and a crossover frequency for each
speaker. Specify “Full Band” for speakers that can
output low frequency bass sounds adequately, for
example, speakers with a good sized woofer. For
smaller speakers, specify a crossover frequency.
Sounds below the crossover frequency will be output
Operating
procedure
(➔ page 52)

Advanced Operations
by the subwoofer instead of the speaker. Refer to
your speaker’s manuals to determine the optimum
crossover frequencies.
■ Subwoofer
` Yes
` No
■ Front
` Full Band
` 40Hz to 100Hz, 120Hz, 150Hz, 200Hz
Note
• If the “Subwoofer” setting is set to “No”, the “Front” setting
is fixed at “Full Band”.

■ Center*1, Surround*1
` Full Band
` 40Hz to 100Hz, 120Hz, 150Hz, 200Hz
` None
■ Front High*1*2*3*5
` Full Band
` 40Hz to 100Hz, 120Hz, 150Hz, 200Hz
` None
■ Surround Back*1*2*3*4
` Full Band
` 40Hz to 100Hz, 120Hz, 150Hz, 200Hz
` None
Note
*1
*2
*3

*4
*5

“Full Band” can be selected only when “Full Band” is
selected in the “Front” setting.
If the “Surround” setting is set to “None”, this setting
cannot be selected.
If the “Speakers Type (Front)” setting is set to
“Bi-Amp”, or the “Powered Zone 2” setting is set to
“Yes” together with Zone 2 turned on, this setting cannot
be selected.
If anything else than “None” is selected in “Front High”,
this setting is automatically set to “None”.
If anything else than “None” is selected in “Surround
Back”, this setting is automatically set to “None”.

■ Surround Back Ch
` 1ch:
Select if only one surround back speaker L is
connected.
` 2ch:
Select if two (left and right) surround back
speakers are connected.
Note
• If the “Surround Back” setting is set to “None”, this setting
cannot be selected.

■ LPF of LFE
(Low-Pass Filter for the LFE Channel)
` 80Hz, 90Hz, 100Hz, 120Hz
` Off:
Low-Pass Filter is not applied.
With this setting, you can specify the cutoff
frequency of the LFE channel’s low-pass filter
(LPF), which can be used to filter out unwanted
hum. The LPF only applies to sources that use the
LFE channel.
■ Double Bass
This setting is NOT set automatically by
Audyssey MultEQ® Room Correction and Speaker
Setup function (➔ page 24).
` On
` Off
Turn this setting on to boost bass output by feeding
bass sounds from the front left, right, and center
channels to the subwoofer. Default setting: “- - - -”

Speaker Distance
This setting is set automatically by
Audyssey MultEQ Room Correction and Speaker
Setup function (➔ page 24).
Here you can specify the distance from each speaker
to the listening position so that the sound from each
speaker arrives at the listener’s ears as the sound
designer intended.
■ Unit
`feet:
Distances can be set in feet. Range: 1.0ft to
30.0ft in 1.0 foot steps.
`meters:
Distances can be set in meters. Range: 0.30m
to 9.00m in 0.30 meter steps.
(The default setting varies from country to country.)
■ Left, Front High Left, Center, Front High Right,
Right, Surround Right, Surround Back Right,
Surround Back Left, Surround Left, Subwoofer
`Specify the distance from each speaker to your
listening position.
Note
• Speakers that you set to “No” or “None” in
“Speaker Configuration” cannot be selected (➔ page 55).
• When the “Powered Zone 2” setting is set to “Yes” and
Zone 2 is turned on, the surround back and front high
speakers cannot be used.

Note
• When the “Subwoofer” setting is set to “No” or the “Front”
setting to anything other than “Full Band”, this setting is
fixed to “- - -”.
• This setting is set to “On” automatically when the
“Subwoofer” and “Front” settings are set for the first time
to “Yes” and “Full Band” respectively.

En-56

Operating
procedure
(➔ page 52)

Advanced Operations

Level Calibration
This setting is set automatically by
Audyssey MultEQ® Room Correction and Speaker
Setup function (➔ page 24).
Here you can adjust the level of each speaker with
the built-in test tone so that the volume of each
speaker is the same at the listening position.
■ Left, Front High Left, Center*1, Front High Right,
Right, Surround Right, Surround Back Right,
Surround Back Left, Surround Left
` –12dB to 0dB to +12dB in 1 dB steps.
■ Subwoofer*1
` –15dB to 0dB to +12dB in 1 dB steps.
Note
• These settings cannot be calibrated when the AV receiver
is muted.
• Speakers that you set to “No” or “None” in
“Speaker Configuration” cannot be selected (➔ page 55).
• When the “Powered Zone 2” setting is set to “Yes” and
Zone 2 is turned on, the surround back and front high
speakers cannot be used.
*1 For the center speaker and subwoofer, the level settings
made by using the Quick Setup are saved in this menu
(➔ page 50).
Tip
• If you’re using a handheld sound level meter, adjust the
level of each speaker so that it reads 75 dB SPL at the
listening position, measured with C-weighting and slow
reading.

3. Audio Adjust
With the Audio Adjust functions and settings, you can
adjust the sound and listening modes as you like.

Multiplex/Mono
■ Multiplex
Input Channel
` Main
` Sub
` Main/Sub
This setting determines which channel of a stereo
multiplex source is output. Use it to select audio
channels or languages with multiplex sources,
multilingual TV broadcasts, and so on.
■ Mono
Input Channel
` Left + Right
` Left
` Right
This setting specifies the channel to be used for
playing any 2-channel digital source such as Dolby
Digital, or 2-channel analog/PCM source in the Mono
listening mode.

Dolby
■ PL IIx Music (2ch Input)
These settings apply to only 2-channel stereo
sources.
If you’re not using any surround back speakers, these
settings apply to Dolby Pro Logic II, not Dolby Pro
Logic IIx.
Panorama
` On
` Off

En-57

With this setting, you can broaden the width of the
front stereo image when using the Dolby Pro Logic IIx
Music listening mode.
Dimension
`–3 to 0 to +3
With this setting, you can move the sound field
forward or backward when using the Dolby Pro Logic
IIx Music listening mode. Higher settings move the
sound field backward. Lower settings move it forward.
If the stereo image feels too wide, or there’s too much
surround sound, move the sound field forward to
improve the balance. Conversely, if the stereo image
feels like it’s in mono, or there’s not enough surround
sound, move it backward.
Center Width
`0 to 3 to 7
With this setting, you can adjust the width of the
sound from the center speaker when using the Dolby
Pro Logic IIx Music listening mode. Normally, if you’re
using a center speaker, the center channel sound is
output from only the center speaker. (If you’re not
using a center speaker, the center channel sound will
be distributed to the front left and right speakers to
create a phantom center.) This setting controls the
front left, right, and center mix, allowing you to adjust
the weight of the center channel sound.
■ PL IIz Height Gain
`Low
`Mid
`High
The Height Gain Control in Dolby Pro Logic IIz
enables the listener to select how much gain is
applied to the front high speakers. There are three
settings, “Low”, “Mid” and “High”, and the front high
speakers are accentuated in that order. While “Mid” is
the default listening setting, the listener may adjust
the Height Gain Control to their personal preference.

Operating
procedure
(➔ page 52)

Advanced Operations
Note
• If the “Front High” settings is set to “None” (➔ page 56),
this setting cannot be selected.
• If the “Powered Zone 2” setting is set to “Yes” and Zone 2
is turned on, this setting cannot be selected.

■ Dolby EX
` Auto:
If the source signal contains a Dolby EX flag, the
Dolby EX listening mode is used.
` Manual:
You can select any available listening mode.
This setting determines how Dolby EX encoded
signals are handled. This setting is unavailable if no
surround back speakers are connected. This setting
is effective with Dolby Digital, Dolby Digital Plus and
Dolby TrueHD only.
Note
• If the “Surround Back” setting is set to “None”
(➔ page 56), this setting cannot be selected.
• If the “Powered Zone 2” setting is set to “Yes” and Zone 2
is turned on, this setting cannot be selected.
• If the “Front High” setting is enabled (➔ page 56), this
setting is fixed to “Manual”.

■ TrueHD Loudness Management
` Off
` On
This setting specifies whether or not to apply the Late
Night processing on a Dolby TrueHD source.
Note
• When this setting is set to “Off”, the Late Night function for
Dolby TrueHD sources is automatically fixed to “Off”.

DTS

Note
• For best results, we recommend setting “Narrow” to 20°
and “Wide” to 40°.

■ Neo:6 Music
Center Image
` 0 to 2 to 5
The DTS Neo:6 Music listening mode creates 6channel surround sound from 2-channel stereo
sources. With this setting, you can specify by how
much the front left and right channel output is
attenuated in order to create the center channel.
Changing the value from “0” to “5” will spread the
sound of the center channel to left and right
(outwards).

Theater-Dimensional
■ Listening Angle
` Wide:
Select if the listening angle is greater than 30
degrees.
` Narrow:
Select if the listening angle is less than 30
degrees.
With this setting, you can optimize the TheaterDimensional listening mode by specifying the angle of
the front left and right speakers relative to the
listening position. Ideally, the front left and right
speakers should be equidistant from the listening
position and at an angle close to one of the two
available settings.
Front left speaker

Front right speaker

4. Source Setup
Items can be set individually for each input selector.
Press the input selector buttons to select an input
source.

Audyssey®
The tone for each speaker is set automatically by
Audyssey MultEQ® Room Correction and Speaker
Setup. To enable the following settings, you must first
perform the Room Correction and Speaker Setup
(➔ page 24).
• These technologies cannot be used when a pair of
headphones is connected.
■ Audyssey
`Off
`Movie:
Select this setting for movie material.
The Audyssey indicator will light.
`Music:
Select this setting for music material.
The Audyssey indicator will light.
Note
• When “Audyssey Quick Start” has been used for
measurement, “Audyssey” cannot be selected.
• Audyssey equalizing does not work with DSD sources.

Listening angle: 30°

En-58

Operating
procedure
(➔ page 52)

Advanced Operations
■ Dynamic EQ
` Off
` On:
Audyssey Dynamic EQ® becomes active.
The Dynamic EQ indicator will light.
With Audyssey Dynamic EQ, you can enjoy great
sound even when listening at low volume levels.
Audyssey Dynamic EQ solves the problem of
deteriorating sound quality as volume is decreased by
taking into account human perception and room
acoustics. It does so by selecting the correct
frequency response and surround volume levels
moment-by-moment so that the content sounds the
way it was created at any volume level — not just at
reference level.
■ Reference Level
Audyssey Dynamic EQ Reference Level Offset
` 0dB:
This should be selected for movie contents.
` 5dB:
Select this setting for content that has a very
wide dynamic range, such as classical music.
` 10dB:
Select this setting for jazz or other music that
has a wider dynamic range. This setting should
also be selected for TV content as that is usually
mixed at 10 dB below film reference.
` 15dB:
Select this setting for pop/rock music or other
program material that is mixed at very high
listening levels and has a compressed dynamic
range.
Movies are mixed in rooms calibrated for film
reference. To achieve the same reference level in a
home theater system each speaker level must be
adjusted so that –30 dBFS band-limited (500 Hz to
2000 Hz) pink noise produces 75 dB sound pressure
level at the listening position. A home theater system
automatically calibrated by Audyssey MultEQ® will

play at reference level when the master volume
control is set to the 64 position. At that level you can
hear the mix as the mixers heard it.
Audyssey Dynamic EQ is referenced to the standard
film mix level. It makes adjustments to maintain the
reference response and surround envelopment when
the volume is turned down from 64. However, film
reference level is not always used in music or other
non-film content. Audyssey Dynamic EQ Reference
Level Offset provides three offsets from the film level
reference (5 dB, 10 dB, and 15 dB) that can be
selected when the mix level of the content is not
within the standard.
Note
• If “Dynamic EQ” setting is set to “Off”, this technology
cannot be used.

■ Dynamic Volume
` Off
` Light:
Activates Light Compression Mode.
` Medium:
Activates Medium Compression Mode.
` Heavy:
Activates Heavy Compression Mode. This
setting affects volume the most. It quiets the
loud parts, such as explosions, and boosts the
quiet parts so they can be heard.
Note
• If you make Dynamic Volume active, “Dynamic EQ” is set
to “On”. The Dynamic Vol indicator will light.
• When “Dynamic EQ” is set to “Off”, “Dynamic Volume” is
automatically switched to “Off”.

En-59

About Audyssey Dynamic EQ®
Audyssey Dynamic EQ solves the problem of
deteriorating sound quality as volume is decreased by
taking into account human perception and room
acoustics. Dynamic EQ selects the correct frequency
response and surround levels moment-by-moment at
any user-selected volume setting. The result is bass
response, tonal balance and surround impression
that remain constant despite changes in volume.
Dynamic EQ combines information from incoming
source levels with actual output sound levels in the
room, a prerequisite for delivering a loudness
correction solution. Audyssey Dynamic EQ works in
tandem with Audyssey MultEQ to provide wellbalanced sound for every listener at any volume level.
About Audyssey Dynamic Volume®
Audyssey Dynamic Volume solves the problem of
large variations in volume level between television
programs, commercials, and between the soft and
loud passages of movies. Dynamic Volume looks at
the preferred volume setting by the user and then
monitors how the volume of program material is being
perceived by listeners in real time to decide whether
an adjustment is needed. Whenever necessary,
Dynamic Volume makes the necessary rapid or
gradual adjustments to maintain the desired playback
volume level while optimizing the dynamic range.
Audyssey Dynamic EQ is integrated into
Dynamic Volume so that as the playback volume is
adjusted automatically, the perceived bass response,
tonal balance, surround impression and dialog clarity
remain the same whether watching movies, flipping
between television channels or changing from stereo
to surround sound content.

Operating
procedure
(➔ page 52)

Advanced Operations

IntelliVolume
■ IntelliVolume
` –12dB to 0dB to +12dB in 1 dB steps
With IntelliVolume, you can set the input level for
each input selector individually. This is useful if one of
your source components is louder or quieter than the
others.
Use e/r to set the level.
If a component is noticeably louder than the others,
use e to reduce its input level. If it’s noticeably
quieter, use r to increase its input level.
Note
• IntelliVolume does not work for Zone 2.

A/V Sync
■ A/V Sync
` 0msec to 800msec in 10 msec steps
When using progressive scanning on your Blu-ray
Disc/DVD player, you may find that the picture and
sound are out of sync. With this setting, you can
correct this by delaying the audio signals.
Press ENTER to view the TV picture while setting the
delay when the video source is output to HDMI OUT
MAIN.
To return to the previous screen, press RETURN.

– “HDMI CEC (RIHD)” is set to “On” (➔ page 64) and
you’re listening through your TV speakers.
• A/V Sync is disabled when the Pure Audio (European,
Australian and Asian models) or Direct listening mode is
used with an analog input source.
• This setting cannot be used with the NET, USB and
BLUETOOTH input selectors.

Name input area
4 - 4. Name Edit

a
n

b
o

1
,

2
.

Name Edit

A
N
!
<

+10

To store a name when you’re done, be sure to
select “OK” by using q/w/e/r, and then press
ENTER.

d
q

e
r

f
s

g
t

h
u

3
4
/
;
Shift

5
:

6
@

7
[

8
9
0
–
^
]
Space
OK
Back Space

i
v

j
w

k
x

B
O
˝
>

l
y

CLR

C
P
#
?

D
Q
$
+

E
R
%

F
S
&
`

G
T
’
{

Shift

■ Name
Use q/w/e/r to select a character, and then
press ENTER.
Repeat this step to enter up to 10 characters.

c
p

Shift

+10

You can enter a custom name for each individual
input selector and radio preset for easy identification.
When entered, the custom name will appear on the
display.
The custom name is edited using the keyboard
screen.

BD/DVD

Name

H
U
(

I
V
)

J
W
_

K
X
=

L
Y
˜

CLR

All Erase

M
Z
|

}
Space
OK
Back Space

Shift

m
z

All Erase

a Toggles between lower and upper case
characters.*1
b Moves the cursor left or right in the Name input
area.
c Moves the cursor backward and deletes one
character.*2
d Enters a space character.
e Confirms your entry.
Tip
• To name a radio preset, use TUNER to select AM or FM,
and then select the preset (➔ page 38).
• To restore a name to its default, erase all characters with
CLR, select “OK” and then press ENTER.
*1 This can also be performed by using +10 on the remote
controller.
*2 Press CLR on the remote controller to delete all the
characters you have input.

The range of values you can adjust will depend on
whether your TV or display supports HDMI Lip Sync
and if the “Lip Sync” setting is set to “On” or not
(➔ page 66).
Note
• This setting is not available in either of the following cases:
– The “Audio TV Out (Main)” setting is set to “On”
(➔ page 65) or “Audio TV Out (Sub)” setting is set to
“On” (➔ page 65) and you’re listening through your TV
speakers.

Note
• This setting cannot be used for the NET, USB and
BLUETOOTH input selectors.

En-60

Operating
procedure
(➔ page 52)

Advanced Operations

Picture Adjust
Using Picture Adjust, you can adjust the picture
quality and reduce any noise appearing on the
screen.
Press ENTER to view the TV picture while setting
when the video source is output to HDMI OUT MAIN.
To return to the previous screen, press RETURN.
■ Wide Mode*1*6
This setting determines the aspect ratio.
` 4:3:

` Full:

` Zoom:

` Wide Zoom:

mode. See “Monitor Out” for details on the
monitor output setting (➔ page 53).
■ Picture Mode*1
` Custom:
All settings can be performed manually.
` Cinema:
Select when the picture source is a movie or
alike.
` Game:
Select when the video source is a game
console.
` Standard:
Does not adjust picture quality (changes
resolution).
` Bypass:
Does not adjust picture quality (does not change
resolution).
With “Picture Mode”, you can change the following
settings to be suitable for the movie or game screen
by one operation: “Game Mode”, “Film Mode”, “Edge
Enhancement”, “Noise Reduction”, “Brightness”,
“Contrast”, “Hue”, “Saturation” or “Color
Temperature”.
■ Game Mode*2*3*4
` Off
` On
If video signal delay occurs during playback on a video
component (i.e., game console), select the
corresponding input source and set the “Game Mode”
setting to “On”. The delay will decrease but in return
the picture quality will become poor.

■ Film Mode*2*4
`Video:
“Film Mode” detection is not applied and the
input signal is handled as a video source.
`Auto:
Detects whether the input signal is a video or a
movie. If it is a movie, the appropriate
conversion is applied.
The AV receiver will adjust to the picture source,
automatically converting it to the appropriate
progressive signal and reproducing the natural quality
of the original picture.
■ Edge Enhancement*2*4*5
`Off
`Low
`Mid
`High
With this setting, you can make the picture appear
sharper.
■ Noise Reduction*2*4*5
`Off
`Low
`Mid
`High
With this setting, you can reduce noise appearing on
the screen. Select the desired level.
■ Brightness*1*2*4
`–50 to 0 to +50
With this setting, you can adjust the picture
brightness. “–50” is the darkest. “+50” is the brightest.
■ Contrast*1*2*4
`–50 to 0 to +50
With this setting, you can adjust contrast. “–50” is the
least. “+50” is the greatest.

` Auto:
According to the input signals and monitor
output setting, the AV receiver automatically
selects the “4:3”, “Full”, “Zoom” or “Wide Zoom”

En-61

Operating
procedure
(➔ page 52)

Advanced Operations
■ Hue*1*2*4
` –50 to 0 to +50
With this setting, you can adjust the color hue
between “–50” and “+50”.
■ Saturation*1*2*4
` –50 to 0 to +50
With this setting, you can adjust saturation. “–50” is
the weakest color. “+50” is the strongest color.
■ Color Temperature*2*4
` Warm
` Normal
` Cool
With this setting, you can adjust the color
temperature.
Note
• “Picture Adjust” cannot be used when:
– The NET, USB or BLUETOOTH input selector is
selected, or
– “Monitor Out” is set to “Sub”.
*1 This procedure can also be performed on the remote
controller by using the Quick Setup (➔ page 48).
*2 When the “Picture Mode” setting is set to anything other
than “Custom”, this setting cannot be used.
*3 If the “Resolution” setting is set to “4K” (➔ page 53),
this setting is fixed at “Off”.
*4 Press CLR if you want to reset to the default value.
*5 If the “Game Mode” setting is set to “On”, this setting is
fixed at “Off”.
*6 When a 3D video source is input, “Wide Mode” is fixed to
“Full”.

Audio Selector

Setting the Incoming Digital Signal (Fixed
Mode)

■ Audio Selector
` ARC:
The audio signal from your TV tuner can be sent
to HDMI OUT MAIN of the AV receiver.*1
With this selection, the TV’s audio can be
automatically selected as a priority among other
assignments.
` HDMI:
This can be selected when HDMI IN has been
assigned as an input source. If both HDMI
(HDMI IN) and digital audio inputs (COAXIAL IN
or OPTICAL IN) have been assigned, HDMI
input is automatically selected as a priority.
` COAXIAL:
This can be selected when COAXIAL IN has
been assigned as an input source. If both
coaxial and HDMI inputs have been assigned,
coaxial input is automatically selected as a
priority.
` OPTICAL:
This can be selected when OPTICAL IN has
been assigned as an input source. If both optical
and HDMI inputs have been assigned, optical
input is automatically selected as a priority.
` Analog:
The AV receiver always outputs analog signals.
You can set priorities of audio output when there are
both digital and analog inputs.
Note

■ Fixed Mode
`Off:
The format is detected automatically. If no digital
input signal is present, the corresponding analog
input is used instead.
`PCM:
Only 2-channel PCM format input signals will be
heard. If the input signal is not PCM, the PCM
indicator will flash and noise may also be
produced.
`DTS:
Only DTS (but not DTS-HD) format input signals
will be heard. If the input signal is not DTS, the
dts indicator will flash and there will be no
sound.
When “HDMI”, “COAXIAL” or “OPTICAL” is selected
in the “Audio Selector” setting, you can then specify
the signal type in “Fixed Mode”.
Normally, the AV receiver detects the signal format
automatically. However, if you experience either of
the following issues when playing PCM or DTS
material, you can manually set the signal format to
PCM or DTS.
• If the beginnings of tracks from a PCM source are
cut off, try setting the format to PCM.
• If noise is produced when fast forwarding or
reversing a DTS CD, try setting the format to DTS.
Note

• This setting can be made only for an input source that is
assigned to HDMI IN, COAXIAL IN, or OPTICAL IN.
• This setting cannot be used with the NET, USB and
BLUETOOTH input selectors.
*1 You can select “ARC” if you select the TV/CD input
selector. But you cannot if you’ve selected “Off” in the
“Audio Return Channel” setting (➔ page 66).

En-62

• The setting will be reset to “Off” when you change the
setting in “Audio Selector”.

Operating
procedure
(➔ page 52)

Advanced Operations
• For the “BLUETOOTH” input selector, only “Digital”
is available.

5. Listening Mode Preset
You can assign a default listening mode to each input
source that will be selected automatically when you
select each input source. For example, you can set
the default listening mode to be used with Dolby
Digital input signals. You can select other listening
modes during playback, but the mode specified here
will be resumed once the AV receiver has been set to
standby.

Use q/w to select the input source that you
want to set, and then press ENTER.
The following menu appears.
5-1. Listening Mode Preset
Analog/PCM
Mono/Multiplex Source
2ch Source
Dolby D/Dolby D Plus/TrueHD
DTS/DTS-ES/DTS-HD
Other Multich Source

BD/DVD
Last Valid e r
Last Valid
Last Valid
Last Valid
Last Valid
Last Valid

Default listening mode for analog and PCM sources.

Use q/w to select the signal format that you
want to set, and then use e/r to select a
listening mode.
Only listening modes that can be used with each
input signal format can be selected (➔ pages 41
to 45).
The “Last Valid” option means that the listening
mode selected last will be used.
The “Straight Decode” option means that
straight decoding listening mode (Dolby Digital,
DTS, etc.) is selected.
Note
• For the “TUNER” input selector, only “Analog” will be
available.
• For the “NET” or “USB” input selector, “Digital” and
“TrueHD“ will be available.

■ Analog/PCM/Digital
With this setting, you can specify the listening mode
used when an analog (CD, TV, LD, VHS, MD,
turntable, radio, cassette, cable, satellite, etc.) or
PCM digital (CD, DVD, etc.) audio signal is played.
■ Mono/Multiplex Source
With this setting, you can specify the listening mode
used when a mono digital audio signal is played
(DVD, etc.).
■ 2ch Source
With this setting, you can specify the listening mode
used when 2-channel (2/0) stereo digital sources,
such as Dolby Digital or DTS, are played.
■ Dolby D/Dolby D Plus/TrueHD
With this setting, you can specify the listening mode
used when Dolby Digital or Dolby Digital Plus
format digital audio signals are played (DVD, etc.).
Specifies the default listening mode for Dolby
TrueHD sources, such as Blu-ray or HD DVD (input
via HDMI).

6. Miscellaneous
Volume Setup
■ Maximum Volume
`Off, 30 to 79
With this setting, you can limit the maximum volume.
To disable this setting, select “Off”.
■ Power On Volume
`Last, Min, 1 to 79 or Max
With this preference, you can specify the volume
setting to be used each time the AV receiver is turned
on.
To use the same volume level that was used when
the AV receiver was turned off, select “Last”.
The “Power On Volume” setting cannot be set higher
than the “Maximum Volume” setting.
■ Headphone Level
`–12dB to 0dB to +12dB
With this setting, you can specify the headphone
volume relative to the main volume. This is useful if
there’s a volume difference between your speakers
and your headphones.

■ DTS/DTS-ES/DTS-HD
With this setting, you can specify the listening mode
used when DTS or DTS-HD High Resolution format
digital audio signals are played (DVD, LD, CD,
etc.). Specifies the default listening mode for DTSHD Master Audio sources, such as Blu-ray or HD
DVD (input via HDMI).
■ Other Multich Source
Specifies the default listening mode for
multichannel PCM sources from HDMI IN such as
DVD-Audio, and DSD multichannel sources such
as Super Audio CD.

En-63

Operating
procedure
(➔ page 52)

Advanced Operations

OSD Setup
■ On Screen Display
` On
` Off
This preference determines whether operation details
are displayed on-screen when an AV receiver
function is adjusted.
Even when “On” is selected, operation details may
not be output if the input source is connected to an
HDMI IN.
■ Language
(North American models)
` English, Deutsch, Français, Español, Italiano,
Nederlands, Svenska
(European, Australian and Asian models)
` English, Deutsch, Français, Español, Italiano,
Nederlands, Svenska, Русский язык, 中文
(Taiwanese models)
` English, Deutsch, Français, Español, Italiano,
Nederlands, Svenska, 中文
This setting determines the language used for the onscreen menus.
■ Screen Saver
` 3min, 5min, 10min
` Off
With this setting, you can set the time until the screen
saver activates itself. Once active, the screen saver
will go off and the screen will return to its previous
state if the AV receiver is operated in any way.

7. Hardware Setup
Tuner
■ AM/FM Frequency Step (North American and
Taiwanese models)
` 10kHz/200kHz:
` 9kHz/50kHz:
Select the frequency step according to your
area.
■ AM Frequency Step (European, Australian and
Asian models)
` 10kHz:
` 9kHz:
Select the frequency step according to your
area.
For AM/FM tuning to work properly, you must specify
the AM/FM frequency step used in your area.
Note
• When this setting is changed, all radio presets will be
deleted.

HDMI
■ HDMI CEC (RIHD)
` Off
` On
Turn this setting on to allow p-compatible
components connected via HDMI to be controlled by
the AV receiver (➔ page 16).

En-64

Note
• When the setting is set to “On” and the menu is closed, the
names of connected p-compatible components and
“RIHD On” are displayed on the AV receiver.
“Search…” → “(name)” → “RIHD On”
When the AV receiver cannot receive the name of the
component, it is displayed as “Player*” or “Recorder*”, etc.
(“*” shows up and indicates the number of components,
when two or more are received).
• When an p-compatible component is connected to
the AV receiver via an HDMI cable, the name of the
connected component is displayed on the AV receiver
display. For example, while you are watching TV
broadcasting, if you operate a Blu-ray Disc/DVD player
(being powered on) with the remote control of the AV
receiver, the name of the Blu-ray Disc/DVD player will be
displayed on the AV receiver.
• Set it to “Off” when a connected piece of equipment is not
compatible or it is unclear whether the equipment is
compatible or not.
• If operation is not normal when set to “On”, change the
setting to “Off”.
• Refer to the connected component’s instruction manual for
details.
• When the “HDMI CEC (RIHD)” setting is set to “On”, the
power consumption on standby mode slightly increases.
(Depending on the TV status, the AV receiver will enter
standby mode as usual.)
• The p control does not support HDMI OUT SUB.
Use HDMI OUT MAIN instead.
• When the source equipment is connected with the u
connection, it may malfunction if “HDMI CEC (RIHD)” is set
to “On”.

Operating
procedure
(➔ page 52)

Advanced Operations
■ HDMI Through
` Off
` BD/DVD, CBL/SAT, GAME, PC, AUX, TV/CD,
PHONO:
Selects the input source for which the HDMI
Through function is enabled.
` Last:
The HDMI Through function is activated on the
input source selected at the time of setting the
AV receiver to standby mode.
When enabling the HDMI Through function,
regardless of whether the AV receiver is on or in
standby, both audio and video streams from an HDMI
input will be output to the TV or other components via
HDMI connection. The HDMI indicator will be dimly-lit
in standby mode. Note that the indicator may not light
under certain conditions (➔ page 22).
This setting is fixed to “Auto” automatically when the
above “HDMI CEC (RIHD)” setting is set to “On”,
resulting in automatic input source selection.
Note
• Only an input source assigned to an HDMI IN via
“HDMI Input” setting is enabled (➔ page 54).
• The power consumption in standby mode will increase
during the HDMI Through function; however in the following
cases, the power consumption can be saved:
– The TV is in standby mode.
– You are watching a TV program.
• Refer to the connected component’s instruction manual for
details.
• Depending on the connected component, the correct input
source may not be selected with the setting fixed to “Auto”.
• This setting is set to “Off” automatically when the “HDMI
CEC (RIHD)” setting is set to “Off”.
• This function is only available for the HDMI OUT MAIN jack.

■ Audio TV Out (Main)
` Off
` On
This preference determines whether the incoming
audio signal is output from HDMI OUT MAIN. You
may want to turn this preference on if your TV is
connected to HDMI OUT MAIN and you want to listen
to the audio from a connected component through
your TV’s speakers. Normally, this should be set to
“Off”.
Note

■ Audio TV Out (Sub)
`Off
`On
This preference determines whether the incoming
audio signal is output from HDMI OUT SUB. You may
want to turn this preference on if your TV is
connected to HDMI OUT SUB and you want to listen
to the audio from a connected component through
your TV’s speakers. Normally, this should be set to
“Off”.
Note

• If “On” is selected and the audio can be output from the TV,
the AV receiver will output no sound through its speakers.
In this case, “TV Speaker” appears on the AV receiver’s
display by pressing DISPLAY.
• When “HDMI CEC (RIHD)” is set to “On”, this setting is
fixed to “Auto”.
• This setting is fixed to “Off” when “Monitor Out” is set to
“Sub” (➔ page 53).
• With some TVs and input signals, no sound may be output
even when this setting is set to “On”.
• When “Audio TV Out (Main)” or “HDMI CEC (RIHD)” is set
to “On” and you’re listening through your TV’s speakers,
turning up the AV receiver’s volume control will make the
sound be output from the AV receiver’s front left and right
speakers. To stop the AV receiver’s speakers producing
sound, change the settings, change your TV’s settings, or
turn down the AV receiver’s volume.
• Listening mode cannot be changed when this setting is set
to “On” and the audio is output from the TV.
• If the audio signal from the player is not supported by the
TV, the audio is not output from the TV even if this setting
is enabled. When the audio cannot be output from the TV,
(When “Monitor Out” is set to “Both”, the audio cannot be
output form the TV connected to both HDMI OUT MAIN and
HDMI OUT SUB) the audio is output from the speakers
connected to the AV receiver.

En-65

• If “On” is selected and the audio can be output from the TV,
the AV receiver will output no sound through its speakers.
In this case, “TV Speaker” appears on the AV receiver’s
display by pressing DISPLAY.
• This setting is fixed to “Off” when “Monitor Out” is set to
“Main” (➔ page 53).
• When “Monitor Out” is set to “Both” (➔ page 53), and this
setting is enabled, set audio output of source component to
2ch PCM.
• With some TVs and input signals, no sound may be output
even when this setting is set to “On”.
• When “Audio TV Out (Sub)” is set to “On” and you’re
listening through your TV’s speakers, turning up the AV
receiver’s volume control will make the sound be output
from the AV receiver’s front left and right speakers. To stop
the AV receiver’s speakers producing sound, change the
settings, change your TV’s settings, or turn down the AV
receiver’s volume.
• Listening mode cannot be changed when this setting is set
to “On” and the audio is output from the TV.
• When “Monitor Out” is set to “Both” (➔ page 53) and only
“Audio TV Out (Sub)” is set to “On”, the audio is not output
from the TV connected to HDMI OUT SUB except in the
case the audio input is via HDMI.
• If the audio signal from the player is not supported by the
TV, the audio is not output from the TV even if this setting
is enabled. When the audio cannot be output from the TV,
(When “Monitor Out” is set to “Both”, the audio cannot be
output form the TV connected to both HDMI OUT MAIN and
HDMI OUT SUB) the audio is output from the speakers
connected to the AV receiver.
Operating
procedure
(➔ page 52)

Advanced Operations
■ Audio Return Channel
` Off
` Auto:
The audio signal from your TV tuner can be sent
to HDMI OUT MAIN of the AV receiver.
The audio return channel (ARC) function allows an
ARC capable TV to send the audio stream to HDMI
OUT MAIN of the AV receiver. To use this function,
you must select the TV/CD input selector and your TV
must be ARC capable. The ARC indicator will light
when the audio signal is detected. Default setting:
“- - - - ”
Note
• This setting is fixed to “- - - -” when the “HDMI CEC (RIHD)”
setting is set to “Off”.
• This setting is set to “Auto” automatically when the “HDMI
CEC (RIHD)” setting is set to “On” for the first time.
• If you set “Audio Return Channel” to “Auto”, the “Audio
Selector” settings of the TV/CD input selector will be
automatically switched to “ARC” (➔ page 62).
Tip
• After changing the settings of the “HDMI CEC (RIHD)”,
“HDMI Through” or “Audio Return Channel”, turn off the
power on all connected pieces of equipment and then turn
them on again. Refer to the user’s manuals for all
connected pieces of equipment.

■ Lip Sync
` Off
` On
This function allows the AV receiver to automatically
correct any delay between the video and the audio,
based on the data from the connected monitor.
Note
• This function works only if your HDMI-compatible TV
supports HDMI Lip Sync.

■ InstaPrevue
These settings apply to “InstaPrevue” of the Home
menu (➔ page 47) and specify the preview display of
HDMI video streams.

Default setting: On (European, Australian and
Asian models), Off (North American and
Taiwanese models)

Sub Window
` Multi:
Displays preview thumbnails all at once.
` Single:
Displays preview thumbnails one-by-one.
With this setting, you can set the number of preview
thumbnails displayed.

• Set to “On”, the Auto Standby function may activate itself
during playback with some sources.
• The Auto Standby function does not work when Zone 2 is
on.

Position
(with “Sub Window” set to “Multi”)
` Top, Bottom, Left, Right
(with “Sub Window” set to “Single”)
` Upper Left, Upper Right, Lower Left, Lower
Right
With this setting, you can set the position of preview
thumbnails on the TV screen.
Note
• Depending on video signals, the picture may not be
properly rendered on the preview thumbnails of
InstaPrevue.

Auto Standby
■ Auto Standby
` Off
` On
When “Auto Standby” is set to “On”, the ASb
indicator lights and the AV receiver will automatically
enter standby mode if there is no operation for 30
minutes with no audio and no video signal input.
“Auto Standby” will appear on the AV receiver’s
display and OSD 30 seconds before the Auto
Standby comes on.

En-66

Note

■ HDMI Through
`Off
`On
This setting enables or disables the Auto Standby
during HDMI Through by detecting the audio/video
input signal.
When this setting is set to “On”, the AV receiver will
automatically enter standby mode if there is no audio
and no video signal input during HDMI Through for 30
minutes. (The Auto Standby function does not work
when Zone 2 is on.)
When this setting is set to “Off”, the status of HDMI
Through is continued regardless of audio/video input
signal.
Tip
• Entering standby mode is possible by setting “HDMI CEC
(RIHD)” to “On” and using CEC-compatible component
regardless of the above-mentioned setting.
See “HDMI CEC (RIHD)” in “7. Hardware Setup” for linked
operation (➔ page 64).
• When the HDMI Through is enabled, the power
consumption slightly increases.
Note
• This setting is fixed to “Off” when “Auto Standby” is set to
“Off”.

Operating
procedure
(➔ page 52)

Advanced Operations

Network
This section explains how to configure the AV
receiver’s network settings manually.
After modifying the network settings, you must
confirm the changes by executing “Save”.
If your router’s DHCP server is enabled, you don’t
need to change any of these settings, as the AV
receiver is set to use DHCP to configure itself
automatically by default (i.e., DHCP is set to
“Enable”). If, however, your router’s DHCP server is
disabled (you’re for example using static IP), you’ll
need to configure these settings yourself, in which
case, a knowledge of Ethernet networking is
essential.
What’s DHCP?
DHCP (Dynamic Host Configuration Protocol) is used
by routers, computers, the AV receiver, and other
devices to automatically configure themselves on a
network.
What’s DNS?
The DNS (Domain Name System) translates domain
names into IP addresses. For example, when you
enter a domain name such as www.onkyousa.com in
your Web browser, before accessing the site, your
browser uses DNS to translate this into an IP
address, in this case 63.148.251.142.
■ Network Connection
` Wired
` Wireless
This setting determines whether you connect the AV
receiver to network by wired LAN or wireless LAN. If
you connect by wireless LAN, select “Wireless”. See
“Performing Wireless LAN Setup” for setting
(➔ page 27).
Tip

■ MAC Address
This is the AV receiver’s MAC (Media Access
Control) address. This address cannot be changed.

■ Proxy Port
If you’re using a Web proxy, enter a proxy port
number here.

■ DHCP
` Enable
` Disable
This setting determines whether or not the AV
receiver uses DHCP to automatically configure its IP
Address, Subnet Mask, Gateway, and DNS Server
settings.

■ Network Standby
`On
`Off
This setting enables or disables control over the
network.
When enabled, the NET indicator will be dimly-lit
while the AV receiver is in standby mode. Note that
the indicator may not light under certain conditions
(➔ page 22).

Note
• If you select “Disable”, you must configure the “IP
Address”, “Subnet Mask”, “Gateway”, and “DNS Server”
settings yourself.

■ IP Address
` Class A:
“10.0.0.0” to “10.255.255.255”
` Class B:
“172.16.0.0” to “172.31.255.255”
` Class C:
“192.168.0.0” to “192.168.255.255”
Enter a static IP address provided by your Internet
Service Provider (ISP).
Most routers use Class C IP addresses.
■ Subnet Mask
Enter the subnet mask address provided by your ISP
(typically 255.255.255.0).

Note
• When set to “On”, the power consumption slightly
increases in standby mode.

■ Update Notice
`Enable
`Disable
When this setting is enabled, you will be notified if a
firmware update via network of high importance is
available.
Note
• Selecting “Never Remind me” on the notification window
will switch this setting to “Disable” (➔ page 22).
• For details on the update notification, see “Firmware
Update Notification” (➔ page 22).

■ Gateway
Enter the gateway address provided by your ISP.
■ DNS Server
Enter the DNS server address provided by your ISP.
■ Proxy URL
To use a Web proxy, enter its URL here.

• The same setting is available even if “Wireless” is selected
in “Network Connection” in initial setup (➔ page 23).

En-67

Operating
procedure
(➔ page 52)

Advanced Operations
■ Bluetooth
This setting enables the AV receiver to pair with
Bluetooth-enabled device.
Status
Press ENTER button to display “Now Pairing” and
start pairing.
Tip
• If pairing setting is not set, “Ready” appears on-screen
display. The name of the device paired with the AV receiver
is displayed if pairing setting is set.
• For details on the Bluetooth connection, refer to the
instruction manual of the Bluetooth-enabled device.
• The pairing can be done by holding down BLUETOOTH
button on the AV receiver until BLUETOOTH indicator
flashes.
Note
• This setting cannot be selected if you’ve selected NET or
USB as input selector in Zone 2.

8. Remote Controller Setup
Remote ID

With this preference, you can protect your settings by
locking the setup menus.

■ Remote ID
` 1, 2, or 3
When several Onkyo components are used in the
same room, their remote ID codes may overlap. To
differentiate the AV receiver from other components,
you can change its remote ID from “1”, to “2” or “3”.

■ Setup
`Locked
`Unlocked
When “Locked” is selected, the setup menus will be
locked and you cannot change any setting.

Note
• If you do change the AV receiver’s remote ID, be sure to
change the remote controller to the same ID (see below),
otherwise, you won’t be able to control it with the remote
controller.

Changing the remote controller’s ID

While holding down RECEIVER, press and
hold down Q SETUP until the remote indicator
lights (about 3 seconds).

Use the number buttons to enter ID 1, 2, or 3.
The remote indicator flashes twice.

Initial Setup
If you skipped the initial setup wizard, for example on
first-time use, you can reaccess it from here.
See “Initial Setup” (➔ page 22).
Note
• This setting cannot be selected if the “Monitor Out” setting
is set to “Sub”.

9. Lock Setup

Remote Mode Setup
See “Looking up for Remote Control Codes”
(➔ page 71).

En-68

Operating
procedure
(➔ page 52)

Advanced Operations

Zone 2
In addition to the main listening room, you can also enjoy playback in another room, or as we call Zone 2. And, you can select a different source for each room.

Making Zone 2 Connections
Connecting Your Zone 2 Speakers Directly to the AV receiver

Connecting the Zone Speakers to an Additional Amplifier

This setup allows you to select different sources for Main room and Zone 2. This is
called Powered Zone, as the Zone 2 speakers are powered by the AV receiver.

This setup allows 7.1-channel playback in your main listening room and 2-channel
stereo playback in Zone 2.

To use this setup, you must activate the Powered Zone 2 setting (➔ page 55).
Main room

Main room

AV receiver

Zone 2
Zone 2

IN
R

Receiver/
integrated amp
Note
• With this setup, the volume of Zone 2 is controlled by the AV receiver.
• When Powered Zone 2 is used, playback in the main room is reduced to 5.1 channels.

Note
• The volume of Zone 2 must be set on the Zone 2 amplifier.

En-69

Advanced Operations

Controlling Zone 2 Components
■ Operating on the AV receiver

Input selector buttons

ZONE 2

OFF

MASTER VOLUME

To turn on Zone 2 and select an input source,
press ZONE 2 followed by an input selector
button within 8 seconds.
Zone 2 turns on, the Z2 indicator lights on the AV
receiver’s display.
To select the same source as the main room’s,
press ZONE 2 twice. “Z2 Sel: Source” appears
on the AV receiver’s display.

To turn off Zone 2, press OFF.
The zone is turned off.

■ Operating on the remote controller
To control Zone 2, you must press ZONE2 on the
remote controller first.

8RECEIVER

ZONE2

Press ZONE2, then point the remote controller
at the AV receiver and press 8RECEIVER.
Zone 2 turns on, the Z2 indicator lights on the AV
receiver’s display.

To select an input source for Zone 2, press
ZONE2, followed by an INPUT SELECTOR
button.

To turn off Zone 2, press ZONE2, followed by
8RECEIVER.
The zone is turned off.

Adjusting the Volume for Zone 2
■ Operating on the remote controller

1
2

Press ZONE2.
Use VOL q/w.

■ Operating on the AV receiver

Press ZONE 2 (the Z2 indicator on the AV
receiver’s display flashes).

Use MASTER VOLUME control within 8
seconds.

If your Zone 2 speakers are connected to a receiver
or integrated amplifier in Zone 2, use its volume
control to adjust the volume.

INPUT
SELECTOR

Muting Zone 2

MUTING

■ Operating on the remote controller

VOLq/w

Press ZONE2 followed by MUTING.

En-70

Tip
• To unmute, press ZONE2 followed by MUTING again.
Zone can also be unmuted by adjusting the volume.
Note
• Only analog, NET or USB input source is output from the
ZONE 2 LINE OUT jacks and ZONE 2 L/R terminals.
• You cannot select different AM or FM radio stations for your
main room and Zone 2. The same AM/FM radio station will
be heard in each room. Namely, if you have selected an FM
station for the main room, that station will also be output in
Zone 2.
• You cannot select different input selector NET or USB for
your main room and Zone 2. Namely, if you have selected
USB input selector for Zone 2, USB input selector will be
selected in main room even if NET has been selected for
main room.
• BLUETOOTH cannot be selected as input selector in
Zone 2. If you play audio from Bluetooth-enabled device in
Zone 2, select “Z2 Sel: Source”, and BLUETOOTH as
input selector in Main room.
• When Zone 2 is activated and its input selector is selected,
the power consumption of standby mode slightly increases.
• While Zone 2 is on, u functions will not work.
• When setting the AV receiver to standby mode while
Zone 2 is active, the Z2 indicator is dimly lit.
• Activating Zones in the main room when the listening mode
is set to Pure Audio (European, Australian and Asian
models) will automatically switch it to Direct.

Controlling Other Components

Controlling Other
Components
You can use the AV receiver’s remote controller to
control your other AV components, including those
made by other manufacturers. This section explains
how to enter the remote control code for a component
that you want to control: DVD, TV, CD, etc.

Use q/w to select “Remote Controller Setup”,
and then press ENTER.

Use q/w to select “Remote Mode Setup”, and
then press ENTER.

Use q/w to select a remote mode, and then
press ENTER.
The menu of category selection appears.

Use q/w to select a category, and then press
ENTER.
The keyboard screen for brand name input
appears.

Use q/w/e/r to select a character, and then
press ENTER.
Repeat this step for the first three characters of
the brand name.
When you have entered the 3rd character, select
“Search” and press ENTER.
A list of brand names is retrieved.
If the desired brand name is not found:
Use r to select “Not Listed”, and then press
ENTER.
The keyboard screen for brand name input
appears.

Preprogrammed Remote Control
Codes
The following REMOTE MODE buttons are
preprogrammed with remote control codes for
controlling the components listed. You do not need to
enter a remote control code to control these
components.
For details on controlling these components, see the
indicated pages.
BD/DVD Onkyo Blu-ray Disc player (➔ page 73)
TV/CD
Onkyo CD player (➔ page 72)
PC
Apple TV

Looking up for Remote Control Codes

Use q/w to select a brand, and then press
ENTER.
A remote control code with its instructions are
displayed. Follow the procedure.

If you can control the component, use q/w to
select “OK”, and then press ENTER.
The on-screen menu returns to the “Remote
Mode Setup” front screen.

You can look up for an appropriate remote control
code from the on-screen menu.
Note
• You need to connect your TV to the HDMI output (HDMI
OUT MAIN) to make the following on-screen setting.

1
2

Press RECEIVER followed by HOME.
Use e/r or q/w to select “Setup”, and then
press ENTER.

Entering Remote Control Codes
You’ll need to enter a code for each component that
you want to control.

Look up the appropriate remote control code
in the separate Remote Control Codes list.
The codes are organized by category (e.g., DVD
player, TV, etc.).

While holding down the REMOTE MODE
button to which you want to assign a code,
press and hold down DISPLAY (about 3
seconds).
The remote indicator lights.
Note
• Remote control codes cannot be entered for
RECEIVER and the multi zone button.
• Only TV remote control codes can be entered for TV.
• Except for RECEIVER, TV, and the multi zone button,
remote control codes from any category can be
assigned for the REMOTE MODE buttons. However,
these buttons also work as input selector buttons, so
choose a REMOTE MODE button that corresponds
with the input to which you connect your component.
For example, if you connect your CD player to the CD
input, choose TV/CD when entering its remote control
code.

Within 30 seconds, use the number buttons to
enter the 5-digit remote control code.
The remote indicator flashes twice.
If the remote control code is not entered
successfully, the remote indicator will flash once
slowly.

Note

If you cannot control the component, use q/w
to select “Try Next Code” and press ENTER.
The next code is displayed.

En-71

• Though the provided remote control codes are correct at
the time of release, they are subject to change.

Operating
procedure
(➔ page 52)

Controlling Other Components

Remapping Colored Buttons
You can change the configuration of colored buttons,
with which REMOTE MODE buttons are preset.

While holding down the REMOTE MODE
button that you want to program, press and
hold down A (Red) until the remote indicator
lights (about 3 seconds).
You can only change colored buttons for
components whose codes belong to categories
of the Remote Control Codes list (BD/DVD
player, TV, cable set-top box, etc).
Within 30 seconds, press the colored buttons
in the order that you want to reassign them.
The button presses are assigned to each button
from left to right. The remote indicator flashes
twice, indicating that the sequence has been
successfully assigned. If the sequence is not
successfully assigned, the remote indicator will
flash once slowly.

Tip
• To reset the REMOTE MODE buttons to their default
settings, see “Resetting the REMOTE MODE Buttons”.
Note
• If any other button than the colored buttons is pressed, the
operation will be cancelled.
• This operation cannot be done while the AV receiver is in
Receiver mode or when Zone 2 is active.

`32901/33104/33504:
Onkyo HD DVD player
`70868:
Onkyo MD recorder without u
`71323:
Onkyo CD recorder without u
`82990:
Onkyo Dock without u

Remote Control Codes for Onkyo
Components Connected via RI
Onkyo components that are connected via u are
controlled by pointing the remote controller at the AV
receiver, not the component. This allows you to
control components that are out of view, in a rack, for
example.

Make sure the Onkyo component is connected
with an u cable and an analog audio cable
(RCA).
See “Connecting Onkyo RI Components” for
details (➔ page 20).
Enter the appropriate remote control code for
a REMOTE MODE button, by referring to the
previous section.
` 42157:
Onkyo cassette tape deck with u
` 81993:
Onkyo Dock with u

Resetting the REMOTE MODE Buttons
You can reset a REMOTE MODE button to its default
remote control code.

While holding down the REMOTE MODE
button that you want to reset, press and hold
down HOME until the remote indicator lights
(about 3 seconds).

Within 30 seconds, press the REMOTE MODE
button again.
The remote indicator flashes twice, indicating that
the button has been reset.
Each REMOTE MODE button is preprogrammed
with a remote control code. When a button is
reset, its preprogrammed code is restored.

Press the REMOTE MODE button, point the
remote controller at the AV receiver, and
operate the component.

Controlling Onkyo components without u
If you want to control an Onkyo component by
pointing the remote controller directly at it, or you
want to control an Onkyo component that’s not
connected via u, use the following remote control
codes:
` 30627:
Onkyo DVD player without u
` 71817:
Onkyo CD player without u
` 32900/33100/33500:
Onkyo Blu-ray Disc player

En-72

Resetting the Remote Controller
You can reset the remote controller to its default
settings.

While holding down RECEIVER, press and
hold down HOME until the remote indicator
lights (about 3 seconds).

Within 30 seconds, press RECEIVER again.
The remote indicator flashes twice, indicating that
the remote controller has been reset.

Controlling Other Components

Controlling Other Components
By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your
component, you can control your component as
described below.
For details on entering a remote control code for other
components, see “Entering Remote Control Codes”
(➔ page 71).

Controlling a TV
TV is preprogrammed with the remote control code
for controlling a TV that supports the p*1
(limited to some models). The TV must be able to
receive remote control commands via p and
be connected to the AV receiver via HDMI. If
controlling your TV via p doesn’t work very
well, program your TV’s remote control code into TV
and use the TV remote mode to control your TV.
Use the following remote control codes:
` 11807/13100/13500:
TV with p

Controlling Apple TV
By programming the supplied remote controller with
the appropriate remote control code, you can use it to
operate your Apple TV.
Use the following remote control codes:
` 02615:
Apple TV

Controlling MHL-Enabled Mobile Device
By programming the supplied remote controller with
the appropriate remote control code, you can use it to
operate your MHL-enabled mobile device.
Connect your MHL-enabled mobile device to the
HDMI IN 1 jack. We advise you to program the
remote control code on the AUX button.
Use the following remote control codes:
(North American and Taiwanese models)
` 33101:
MHL-enabled mobile device
(European, Australian, and Asian models)
` 32910:
MHL-enabled mobile device
Note
• With some mobile devices, reliable operation cannot be
guaranteed.

Controlling a Blu-ray Disc/DVD Player, HD
DVD Player or DVD Recorder
BD/DVD is preprogrammed with the remote control
code for controlling a component that supports the
p*1 (limited to some models). The component
must be able to receive remote control commands via
p and be connected to the AV receiver via
HDMI.
Use the following remote control codes:
` 32910/33101/33501/31612:
Blu-ray Disc/DVD player with p
*1

The p supported by the AV receiver is the CEC
system control function of the HDMI standard.

En-73

Press the appropriate REMOTE
MODE button first.

i
j
a
b

k
l

c
d

m
n

e
f
g
o

Controlling Other Components
■ TV operation

■ DVD player/DVD recorder operation

■ Satellite receiver/Cable receiver operation

Available buttons

a 8, INPUT, TV VOL q/w, g Number: 1 to 9, 0
MUTING
Number: +10*1

b TOP MENU

h 8SOURCE

b GUIDE

h 8SOURCE

c q/w/e/r, ENTER

i DISPLAY

c q/w/e/r, ENTER

i DISPLAY

b GUIDE

d SETUP

j MUTING
k CH +/–

d SETUP

j MUTING
k CH +/–

c q/w/e/r, ENTER
d SETUP
e 1, 3, 2, 5, 4,
7, 6*1
f A (Red)*1
B (Green)*1

i DISPLAY
k CH +/–
l PREV CH
m RETURN
n AUDIO*1
o CLR

C (Yellow)*1

e 1, 3, 2, 5, 4,
7, 6
f A (Red)*1
B (Green)

DISC +/–

e 1, 3, 2, 5, 4,
7, 6

l MENU
m RETURN

f A (Red)
B (Green)

AUDIO*1

C (Yellow)

C (Yellow)*1

D (Blue)*1

o CLR

l PREV CH
m RETURN
n AUDIO
o CLR

D (Blue)

g Number: 1 to 9, 0
Number: +10*1

g Number: 1 to 9, 0
Number: +10

■ Blu-ray Disc player/HD DVD player operation

■ VCR/PVR operation

■ CD player/CD recorder/MD recorder operation

Available buttons

D (Blue)*1

b TOP MENU

h 8SOURCE

b GUIDE

h 8SOURCE

c q/w/e/r, ENTER

i DISPLAY

c q/w/e/r, ENTER

i DISPLAY

d SETUP

j MUTING
k CH +/–

d SETUP

j MUTING
k CH +/–

e 1, 3, 2, 5, 4,
7, 6

l PREV CH
m RETURN

f SEARCH
REPEAT

e 1, 3, 2, 5, 4,
7, 6

DISC +/–

e 1, 3, 2, 5, 4,
7, 6

f A (Red)
B (Green)

l MENU
m RETURN

g Number: 1 to 9, 0
Number: +10

C (Yellow)

n AUDIO*1
o CLR

■ Cassette tape deck operation

D (Blue)
g Number: 1 to 9, 0
Number: +10*1

o CLR

Available buttons

RANDOM

g Number: 1 to 9, 0
Number: +10
h 8SOURCE
i DISPLAY
j MUTING
k DISC +/–
o CLR

MODE
Note

e 1, t (Reverse
h 8SOURCE
Playback), 2, 5, 4, j MUTING
7, 6

En-74

• With some components, certain buttons may not work as
expected, and some may not work at all.
• See “Controlling Your iPod/iPhone” about the operation of
iPod/iPhone (➔ page 76).
*1 The p function is not supported. The p
supported by the AV receiver is the CEC system control
function of the HDMI standard.

Controlling Other Components

Using the Onkyo Dock
RI Dock
With the RI Dock, you can easily play the music of
your iPod/iPhone, or watch the slideshows and
videos of your iPod/iPhone on a TV. In addition, the
on-screen display (OSD) allows you to view,
navigate, and select your iPod/iPhone model’s
contents on your TV, and with the supplied remote
controller, you can control your iPod/iPhone from the
comfort of your sofa. You can even use the AV
receiver’s remote controller to operate your
iPod/iPhone.
Note
• Enter the appropriate remote control code before using the
AV receiver’s remote controller for the first time
(➔ page 72).
• Connect the RI Dock to the AV receiver with an u cable
(➔ page 20).
• Set the RI Dock’s RI MODE switch to “HDD” or
“HDD/DOCK”.
• Set the AV receiver’s Input Display to “DOCK”
(➔ page 46).

■ System Function
System On
When you turn on the AV receiver, the RI Dock and
iPod/iPhone turn on automatically. In addition, when
RI Dock and iPod/iPhone are on, the AV receiver can
be turned on by pressing 8SOURCE.
Auto Power On
If you press the remote controller’s 1 (Playback)
while the AV receiver is on standby, the AV receiver
will automatically turn on, select your iPod/iPhone as
the input source, and your iPod/iPhone will start
playback.

Direct Change
If you start iPod/iPhone playback while listening to
another input source, the AV receiver will
automatically switch to the input to which the RI Dock
is connected.
Other Remote Operations
You can use the remote controller that came with the
AV receiver to control other iPod/iPhone functions.
The available functionality depends on the AV
receiver.
Note
• If you use your iPod/iPhone with any other accessories,
iPod/iPhone playback detection may not work.
• The System On function may not work depending on the RI
Dock.

iPod Alarm
If you use the Alarm function on your iPod to start
playback, the AV receiver will turn on at the specified
time and select your iPod as the input source
automatically.
Note
• Depending on your iPod/iPhone model and generation,
some of the linked operations may not be available.
• This linked operation won’t work while a video is being
played or when the sound set for the alarm is a built-in
sound (Beep).
• This linked operation won’t work with models on which
music files cannot be used to set the alarm sound.

■ Operating Notes
• Use the AV receiver’s volume control to adjust the playback
volume.
• While your iPod/iPhone is inserted in the RI Dock, its
volume control has no effect.
• If you do adjust the volume control on your iPod/iPhone
while it’s inserted in the RI Dock, be careful that it’s not set
too loud before you reconnect your headphones.

En-75

The Dock is sold separately. Models sold are
different depending on the region.
For the latest information on the Onkyo Dock
components, see the Onkyo web site at:
http://www.onkyo.com
Before using the Onkyo Dock components, update
your iPod/iPhone with the latest software, available
from the Apple web site.
For supported iPod/iPhone models, see the
instruction manual of the Onkyo Dock.

Controlling Other Components
■ u Dock operation

Controlling Your iPod/iPhone

Press the appropriate REMOTE
MODE button first.

By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your
Dock, you can control your iPod/iPhone in the Dock
with the buttons described further in this section.
See “Entering Remote Control Codes” for details on
entering a remote control code (➔ page 71).
See the Dock’s instruction manual for more
information.

e
f
g
h

RI Dock
• Set the RI Dock’s RI MODE switch to “HDD” or
“HDD/DOCK”.
• 8SOURCE may not work with a remote control
code (without u). In this case, make an u
connection and enter the remote control code 81993
(with u).
■ With the RI Control
Make an u connection and enter the remote control
code 81993 (with u).
• Set the AV receiver’s Input Display to “DOCK”
(➔ page 46).
■ Without the RI Control
You must enter the remote control code 82990 first
(➔ page 72).

Available buttons

i
a

c
k

En-76

a TOP MENU*1

e 8SOURCE*2

b q/w/e/r, ENTER

f DISPLAY*3

PLAYLIST e/r

g MUTING

c 1, 3, 2, 5, 4,
7, 6

h ALBUM +/–

d REPEAT
RANDOM

j MENU
k MODE*4

i VOL q/w

• With some iPod/iPhone models, generations and RI Docks,
certain buttons may not work as expected.
• For detailed operation of iPod/iPhone, please refer to the
instruction manual of the RI Dock.
*1 TOP MENU works as the mode button when used with
the DS-A2 RI Dock.
*2 This button does not turn the Onkyo DS-A2 or DS-A2X
RI Dock on or off. Also, your iPod/iPhone may not
respond the first time you press this button, in which case
you should press it again. This is because the remote
controller transmits the On and Standby commands
alternately, so if your iPod/iPhone is already on, it will
remain on when the remote controller transmits the On
command. Similarly, if your iPod/iPhone is already off, it
will remain off when the remote controller transmits the
Off command.
*3 DISPLAY turns on the backlight for a few seconds.
*4 Resume mode
With the Resume function, you can resume playback of
the song that was playing when you removed your
iPod/iPhone from the Onkyo DS-A2 RI Dock.

Appendix

Troubleshooting
If you have any trouble using the AV receiver, look for
a solution in this section. If you can’t resolve the issue
yourself, contact your Onkyo dealer.

seconds). Within 30 seconds, press RECEIVER
again.
The on-screen menus appear only on a TV that is
connected to HDMI OUT MAIN.

■ Can’t turn on the AV receiver

If you can’t resolve the issue yourself, try resetting the
AV receiver before contacting your Onkyo dealer.
To reset the AV receiver to its factory defaults, turn it
on and, while holding down CBL/SAT, press
8ON/STANDBY. “Clear” will appear on the AV
receiver’s display and the AV receiver will enter
standby mode.

Make sure that the power cord is properly plugged into the
wall outlet.

Remote indicator

■ The AV receiver turns off unexpectedly

Make sure that the input source is properly selected.
(➔ page 29)

The AV receiver will automatically enter standby mode
when Auto Standby has been set and launches.
(➔ page 66)

Make sure that the speaker cables are not shorting.
(➔ page 14)

The protection circuit has been activated. Remove the
power cord from the wall outlet immediately. Make sure
that all speaker cables and input sources are properly
connected, and leave the AV receiver with its power cord
disconnected for 1 hour. After that, reconnect the power
cord and turn the power on. If the AV receiver turns off
again, avoid resetting it and unplug the power cord. Then
contact your Onkyo dealer. (➔ page 14)

• If “CHECK SP WIRE” appears on the AV receiver’s
display, the speaker cables may be shorting.

WARNING:
HOME

Make sure that the inputs and outputs of all components
are connected properly. (➔ pages 15 to 20)
Make sure that the polarity of the speaker cables is correct,
and that the bare wires are in contact with the metal part of
each speaker terminal. (➔ page 13)

Caution:
RECEIVER

Make sure that the digital input source is selected properly.
(➔ page 55)

Unplug the power cord from the wall outlet, wait five
seconds or more, then plug it in again.

■ The AV receiver turns off and after restoring the
power, it turns off again
Note that resetting the AV receiver will delete your
radio presets and custom settings.

■ There’s no sound, or it’s very quiet

Make sure that all audio connecting plugs are pushed in all
the way (➔ page 15).

Power
Resetting the AV receiver

Audio

• If smoke, smell or abnormal noise is produced by the AV
receiver, unplug the power cord from the wall outlet
immediately and contact your Onkyo dealer.

Check the volume. The AV receiver is designed for home
theater enjoyment. It has a wide volume range, allowing
precise adjustment.
If the MUTING indicator is flashing on the AV receiver’s
display, press the remote controller’s MUTING button to
unmute the AV receiver. (➔ page 46)
While a pair of headphones is connected to the PHONES
jack, no sound is output from the speakers. (➔ page 20)
If there’s no sound from a DVD player connected to an
HDMI IN, check the DVD player’s output settings, and be
sure to select a supported audio format.
Check the digital audio output setting on the connected
device. On some game consoles, such as those that
support DVD, the default setting is off.
With some DVD-Video discs, you need to select an audio
output format from a menu.
If your turntable uses an MC cartridge, you must connect
an MC head amp, or an MC transformer.
Make sure that none of the connecting cables are bent,
twisted, or damaged.
Not all listening modes use all speakers. (➔ page 41)
Specify the speaker distances and adjust the individual
speaker levels. (➔ page 56, 57)

To reset the remote controller to its factory defaults,
while holding down RECEIVER, press and hold down
HOME until the remote indicator lights (about 3

Make sure that the speaker setup microphone is not still
connected.

En-77

Appendix
If the input signal format is set to “PCM” or “DTS”. Set it to
“Off”. (➔ page 62)

■ Only the front speakers produce sound
When the Stereo or Mono listening mode is selected, only
the front speakers and subwoofer produce sound.
(➔ page 43)

When Powered Zone 2 is used, playback in the main room
is reduced to 5.1channels and the front high and surround
back speakers produce no sound.

■ The subwoofer produces no sound
When you play source material that contains no information
in the LFE channel, the subwoofer produces no sound.

Make sure the speakers are configured correctly.
(➔ page 55)

■ Only the center speaker produces sound

■ There’s no sound with a certain signal format

If you use the Dolby Pro Logic IIx Movie, Dolby Pro Logic
IIx Music, or Dolby Pro Logic IIx Game listening mode with
a mono source, such as an AM radio station or mono TV
program, the sound is concentrated in the center speaker.

Check the digital audio output setting on the connected
device. On some game consoles, such as those that
support DVD, the default setting is off.

Make sure the speakers are configured correctly.
(➔ page 55)

■ The surround speakers produce no sound
When the T-D (Theater-Dimensional), Stereo or Mono
listening mode is selected, the surround speakers produce
no sound.
Depending on the source and current listening mode, not
much sound may be produced by the surround speakers.
Try selecting another listening mode. (➔ page 41)
Make sure the speakers are configured correctly.
(➔ page 55)

■ The center speaker produces no sound
When the Stereo or Mono listening mode is selected, the
center speaker produces no sound.
Make sure the speakers are configured correctly.
(➔ page 55)

■ The front high and surround back speakers
produce no sound
Depending on the current listening mode, no sound may be
produced by the front high and surround back speakers.
Select another listening mode. (➔ page 41)
Depending on the sources, the sound produced by the
front high and surround back speakers may be weak.

With some DVD-Video discs, you need to select an audio
output format from a menu.
Depending on the input signal, some listening modes
cannot be selected. (➔ pages 41 to 45)

■ Can’t select the Pure Audio listening mode
(European, Australian and Asian models) The Pure
Audio listening mode cannot be selected while Zone 2 is
on.

■ Can’t get 6.1/7.1 playback
If no surround back speakers and front high speakers are
connected, or the Zone 2 speakers are being used, 6.1/7.1
playback is not possible.
Depending on the number of connected speakers, it is not
always possible to select all of the listening modes.
(➔ pages 41 to 45)

■ The speaker volume cannot be set as required
Check to see if a maximum volume has been set.
(➔ page 63)
If the volume level of each individual speaker has been
adjusted to high positive values, then the maximum master
volume possible may be reduced. Note that the individual
speaker volume levels are set automatically after the
Audyssey MultEQ® Room Correction and Speaker Setup
has been performed. (➔ pages 24, 57)

Make sure the speakers are configured correctly.
(➔ page 55)

En-78

■ Noise can be heard
Using cable ties to bundle audio cables with power cords,
speaker cables, and the like may degrade the audio
performance, so refrain from doing it.
An audio cable may be picking up interference. Try
repositioning your cables.

■ The Late Night function doesn’t work
Make sure the source material is Dolby Digital, Dolby
Digital Plus, and Dolby TrueHD. (➔ page 50)
Make sure that the “TrueHD Loudness Management”
setting is not set to “Off”. The Late Night function doesn’t
work when this setting is disabled. (➔ page 58)

■ About DTS signals
When DTS program material ends and the DTS bitstream
stops, the AV receiver remains in DTS listening mode and
the dts indicator remains on. This is to prevent noise when
you use the pause, fast forward, or fast reverse function on
your player. If you switch your player from DTS to PCM,
you may not hear any sound because the AV receiver does
not switch formats immediately. In such case, you should
stop your player for about three seconds and then resume
playback.
With some CD and LD players, you won’t be able to
playback DTS material properly even though your player is
connected to a digital input on the AV receiver. This is
usually because the DTS bitstream has been processed
(e.g., output level, sampling rate, or frequency response
changed) and the AV receiver doesn’t recognize it as a
genuine DTS signal. In such cases, you may hear noise.
Playing DTS program material, using the pause, fast
forward, or fast reverse function on your player may
produce a short audible noise. This is not a malfunction.

■ The beginning of audio received by an HDMI IN
can’t be heard
Since it takes longer to identify the format of an HDMI
signal than it does for other digital audio signals, audio
output may not start immediately.

Appendix
■ The on-screen menus don’t appear

■ There’s no picture

On your TV, make sure that the video input to which the AV
receiver is connected is selected.

If the AV receiver is installed in a rack or cabinet with
colored-glass doors, the remote controller may not work
reliably when the doors are closed.

Make sure that all video connecting plugs are pushed in all
the way. (➔ page 18)

When the AV receiver is not connected to a TV via HDMI
OUT MAIN, on-screen menus are not displayed.

Make sure you’ve selected the correct remote controller
mode. (➔ pages 11, 73)

Make sure that each video component is properly
connected. (➔ page 15)

■ The on-screen display does not appear

When using the remote controller to control other
manufacturers’ AV components, some buttons may not
work as expected.

Video

If your TV is connected to the HDMI output(s), select
“- - - - -” in the “HDMI Input” setting to watch composite
video, and component video sources. (➔ page 54)
If the video source is connected to a component video
input, you must assign that input to an input selector, and
your TV must be connected to either the HDMI output(s) or
COMPONENT VIDEO OUT. (➔ pages 15, 54)

Depending on the input signal, the on-screen display may
not appear when the input signal from HDMI IN is output to
a device connected to HDMI OUT MAIN.

Make sure you’ve entered the correct remote control code.
(➔ page 71)
Make sure to set the same ID on both the AV receiver and
remote controller. (➔ page 68)

Tuner
■ Reception is noisy, FM stereo reception is noisy,
or the FM STEREO indicator doesn’t light

■ Can’t control other components

If the video source is connected to an HDMI input, you
must assign that input to an input selector, and your TV
must be connected to the HDMI output(s). (➔ pages 15,
54)

Listen to the station in mono. (➔ page 38)

If it’s an Onkyo component, make sure that the u cable
and analog audio cable are connected properly.
Connecting only an u cable won’t be enough.
(➔ page 20)

When listening to an AM station, operating the remote
controller may cause noise.

Make sure you’ve selected the correct remote controller
mode. (➔ pages 11, 73)

Passing cars and airplanes can cause interference.

(European, Australian and Asian models) While the
Pure Audio listening mode is selected, the analog video
circuitry is turned off and only video signals input through
HDMI IN can be output. (➔ page 41)

Concrete walls weaken radio signals.

If you’ve connected an cassette tape deck to the TV/CD IN
jack, or an RI Dock to the TV/CD IN or GAME IN jacks, for
the remote controller to work properly, you must set the
input display appropriately. (➔ page 46)

If the video source is connected to a composite video input,
your TV must be connected to the HDMI output(s) or the
corresponding composite video output. (➔ page 15)

On your TV, make sure that the video input to which the AV
receiver is connected is selected.

Relocate your antenna.
Move the AV receiver away from your TV or computer.

If nothing improves the reception, install an outdoor
antenna.

Remote Controller

When the “Monitor Out” setting is set to “Both”, the “HDMI
Through” setting is only available for the HDMI OUT MAIN
jack. (➔ pages 53, 65)

■ The remote controller doesn’t work

■ There’s no picture from a source connected to
an HDMI IN

Make sure that the batteries are installed with the correct
polarity. (➔ page 11)

Reliable operation with an HDMI-to-DVI adapter is not
guaranteed. In addition, video signals from a PC are not
guaranteed. (➔ page 88)
When the resolution is set to any resolution not supported
by the TV, no video is output from the HDMI outputs.
(➔ page 53)
If the message “Resolution Error” appears on the AV
receiver’s display, this indicates that your TV does not
support the current video resolution and you need to select
another resolution on your DVD player.

Before operating this unit, be sure to press RECEIVER.

Install new batteries. Don’t mix different types of batteries,
or old and new batteries. (➔ page 11)
Make sure that the remote controller is not too far away
from the AV receiver, and that there’s no obstruction
between the remote controller and the AV receiver’s
remote control sensor. (➔ page 11)
Make sure that the AV receiver is not subjected to direct
sunshine or inverter-type fluorescent lights. Relocate if
necessary.

En-79

If you cannot operate it, you will need to enter the
appropriate remote control code. (➔ page 71)
To control another manufacturer’s component, point the
remote controller at that component. (➔ page 71)
To control an Onkyo component that’s connected via u,
point the remote controller at the AV receiver. Be sure to
enter the appropriate remote control code first.
(➔ page 72)
To control an Onkyo component that’s not connected via
u, point the remote controller at the component. Be sure
to enter the appropriate remote control code first.
(➔ page 72)
The entered remote control code may not be correct. If
more than one code is listed, try each one.

Appendix

RI Dock for iPod/iPhone

■ iPod/iPhone doesn’t work properly
Try reconnecting your iPod/iPhone.

If there is more than one access point in the network,
separate each access point.

Zone 2

It is recommended to place the Wi-Fi router (access point)
and the AV receiver in the same room.

■ There’s no sound
Make sure your iPod/iPhone is actually playing.
Make sure your iPod/iPhone is properly inserted in the
Dock.

■ There’s no sound

Make sure the AV receiver is turned on, the correct input
source is selected, and the volume is turned up.

Audio can be output only when analog, NET or USB input
source is selected in Zone 2.

Make sure the plugs are pushed in all the way.

■ The Zone 2 speakers produce no sound

Try resetting your iPod/iPhone.

Powered Zone 2 cannot be used if “Speakers Type
(Front)” is set to “Bi-Amp”. (➔ page 55)

■ There’s no video
Make sure that your iPod/iPhone model’s TV OUT setting
is set to On.
Make sure the correct input is selected on your TV or the
AV receiver.
Some versions of the iPod/iPhone do not output video.

■ The AV receiver’s remote controller doesn’t
control my iPod/iPhone
Make sure your iPod/iPhone is properly inserted in the
Dock. If your iPod/iPhone is in a case, it may not connect
properly to the Dock. Always remove your iPod/iPhone
from the case before inserting it into the Dock.
The iPod/iPhone cannot be operated while it’s displaying
the Apple logo.
Make sure you’ve selected the right remote mode.
(➔ page 76)
When you use the AV receiver’s remote controller, point it
toward your AV receiver.
If you still can’t control your iPod/iPhone, start playback by
pressing your iPod/iPhone model’s Play button. Remote
operation should then be possible.
Try resetting your iPod/iPhone.
Depending on your iPod/iPhone, some buttons may not
work as expected.

■ The AV receiver unexpectedly selects my
iPod/iPhone as the input source
Always pause iPod/iPhone playback before selecting a
different input source. If playback is not paused, the Direct
Change function may select your iPod/iPhone as the input
source by mistake during the transition between tracks.

Wi-Fi (Wireless LAN) Network
■ Cannot access to Wi-Fi (Wireless LAN) network
or Sound playback is interrupted and
communication doesn’t work
The setting of SSID and encryption (WEP, etc.) is not
correct. Make the same settings for network and the AV
receiver.
Cannot receive radio wave due to a bad connection.
Shorten the distance from wireless LAN access point or
remove obstacles for a good visibility, and try again. Place
the AV receiver away from microwave ovens or other
access points.
2.4 GHz band for wireless LAN may not be enough.
Connect the ETHERNET port and router with the Ethernet
cable after selecting “Wired” in “Network Connection”
setting in “Network”. (➔ pages 16, 67)
Place the AV receiver away from the devices emitting
electromagnetic waves on the 2.4 GHz band (microwave
ovens, game consoles, etc.). If this does not solve the
problem, stop using other devices which emit
electromagnetic waves.
When other wireless LAN devices are used near the AV
receiver, several issues such as interrupted playback and
communication may occur. You can avoid these issues by
changing the channel of your Wi-Fi router. For instructions
on changing channels, see the instruction manual provided
with your Wi-Fi router.
If there is a metallic object near the AV receiver, wireless
LAN connection may not be possible as the metal can
effect on the radio wave.

En-80

Bluetooth
■ Music playback is unavailable on the AV
receiver even after successful Bluetooth
connection.
Depending on the characteristics or specifications of your
Bluetooth-enabled device, playback on the AV receiver is
not guaranteed.

■ The audio quality is poor after connection with a
Bluetooth-enabled device.
The Bluetooth reception is poor. Move the Bluetoothenabled device closer to the AV receiver or remove any
obstacle between the Bluetooth-enabled device and the AV
receiver.

■ Cannot connect with the AV receiver.
The Bluetooth-enabled device does not support the profiles
required for the AV receiver.
The Bluetooth function of the Bluetooth-enabled device is
not enabled. Refer to the user manual of the Bluetoothenabled device for how to enable the function.

■ Bluetooth connection cannot be built
When building a Bluetooth connection between the AV
receiver and your Bluetooth-enabled device for the first
time, if the connection is fail, you need to power off your
Bluetooth-enabled device and power on again to clear the
device name, and build the connection again.
If there is metallic object near the AV receiver, Bluetooth
connection may not be possible as the metal can effect on
the radio wave.
If the wireless LAN and Bluetooth connections are used at
the same time, try to connect the ETHERNET port and
router with the Ethernet cable after selecting “Wired” in
“Network Connection” setting in “Network” for a better
connection. (➔ pages 16, 67)

Appendix
The AV receiver supports USB devices that support the
USB mass storage device class. However, playback may
not be possible with some USB devices even if they
conform to the USB mass storage device class.
(➔ page 89)

■ The u functions don’t work

Check the network connection between the AV receiver
and your router or switch. (➔ page 16)

Depending on the type of format, the playback from a USB
device may not be performed normally. Check the type of
the file formats that is supported. (➔ page 90)

While Zone 2 is selected, the u functions don’t work.
(➔ page 20)

Make sure that your modem and router are properly
connected, and make sure they are both turned on.

USB memory devices with security functions cannot be
played.

Make sure the server is up and running and compatible
with the AV receiver. (➔ page 89)

■ The functions System On/Auto Power On and
Direct Change don’t work for components
connected via u

Others

These functions don’t work when Zone 2 is turned on.
(➔ page 20)

Music Server and Internet Radio
■ Can’t access the server or Internet radio
Certain network service or contents available through this
device may not be accessible in case the service provider
terminates its service.

Check the “Network”settings. (➔ page 67)

■ Playback stops while listening to music files on
the server
Make sure your server is compatible with the AV receiver.
(➔ page 89)
If you download or copy large files on your computer,
playback may be interrupted. Try closing any unused
programs, use a more powerful computer, or use a
dedicated server.
If the server is serving large music files to several
networked devices simultaneously, the network may
become overloaded and playback may be interrupted.
Reduce the number of playback devices on the network,
upgrade your network, or use a switch instead of a hub.

■ Can’t connect to the AV receiver from a Web
browser
If you’re using DHCP, your router may not always allocate
the same IP address to the AV receiver, so if you find that
you can’t connect to a server or Internet radio station,
recheck the AV receiver’s IP address on the “Network”
screen. (➔ page 67)
Check the “Network” settings. (➔ page 67)

■ Standby power consumption
In the following cases, the power consumption in standby
mode may reach up to a maximum of 8.6 W:
– The “HDMI CEC (RIHD)” setting is set to “On”.
(Depending on the TV status, the AV receiver will enter
standby mode as usual.)
– The “HDMI Through” setting is set to other than “Off”.
– The “Network Standby” setting is set to “On”.
(➔ pages 64, 65, 67)
If an MHL-enabled mobile device connected to HDMI IN 1
is charged, the power consumption in standby mode will
increase than the figure above. (➔ page 16)

■ The sound changes when I connect my
headphones
When a pair of headphones is connected, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, Direct, or Pure Audio (European, Australian and
Asian models).

■ The speaker distance cannot be set as required
The values entered may be automatically adjusted with
values best-suited for your home theater.

■ The display doesn’t work

USB Device Playback
■ Can’t access the music files on a USB device
Make sure the USB device is plugged in properly.

The display is turned off when the Pure Audio (European,
Australian and Asian models) listening mode is selected.

■ How do I change the language of a multiplex
source
Use the “Multiplex” setting in the “Audio Adjust” menu to
select “Main” or “Sub”. (➔ page 57)

En-81

To use u, you must make an u connection and an
analog audio connection (RCA) between the component
and AV receiver, even if they are connected digitally.
(➔ page 20)

■ When performing Automatic Speaker Setup, the
measurement fails and the message “Ambient
noise is too high.” is displayed.
This can be caused by a malfunction in your speaker unit.
Check if the unit produces normal sounds.

■ The following settings can be made for the
composite video inputs
You must use the buttons on the unit to make these
settings.
On the AV receiver, press the input selector for the
input source that you want to set and the HOME
button simultaneously. While holding down the
input selector button, press HOME until “Video
ATT :On” appears on the AV receiver’s display.
Then, release both buttons. To turn the setting off,
repeat the above process so that “Video ATT :Off”
appears on the AV receiver’s display, and release
the buttons.
• Video Attenuation
This setting can be made for the BD/DVD,
CBL/SAT, GAME, PC or AUX input.
If you have a game console connected to the
composite video input, and the picture isn’t very
clear, you can attenuate the gain.
Video ATT :Off: (default).
Video ATT :On: Gain is reduced by 2 dB.

Appendix
■ If the picture on your TV/monitor connected to
the HDMI output(s) is unstable, try switching the
DeepColor function off
To turn off the DeepColor function, simultaneously
press the GAME and 8ON/STANDBY buttons on
the AV receiver. While holding down GAME, press
8ON/STANDBY until “Deep Color:Off” appears
on the AV receiver’s display. Then, release both
buttons. To reactivate the DeepColor function,
repeat the above process until “Deep Color:On”
appears on the AV receiver’s display and release
the buttons.

Radio Wave Caution
The AV receiver uses a 2.4 GHz radio wave
frequency, which is a band used by other wireless
systems as 1 and 2 described below.
1. Devices which use a 2.4 GHz radio wave
frequency
• Cordless phones
• Cordless facsimiles
• Microwave ovens
• Wireless LAN devices (IEEE802.11b/g/n)
• Wireless AV equipment
• Wireless controllers for game systems
• Microwave oven-based health aids
• Video transmitter
• Specific type of external monitor and LCD
display
2. Less common devices which use a 2.4 GHz
radio wave frequency
• Anti-theft systems
• Amateur radio stations (HAM)
• Warehouse logistic management systems
• Discrimination systems for train or emergency
vehicles
If these devices and the AV receiver are used at the
same time, the audio may be undesirably stopped or
disturbed due to a radio wave interference.
Suggestions for improvement
• Switch off the devices which emit the radio
wave.
• Place the interfering devices away from the AV
receiver.
• The AV receiver uses radio wave, and a third
person can receive the wave on purpose or
accidentally. Do not use the communication for
important or fatal matters.

En-82

• We assume no responsibility whatsoever for any
error or damage of network environment or access
device resulting from the use of this apparatus.
Confirm with the provider or access device maker
for more information.

Scope of Operation
Use of the AV receiver is limited to home use.
(Transmission distances may be reduced depending
on communication environment.)
In the following locations, poor condition or
inability to receive radio waves may cause the
audio to be interrupted or stopped:
• In reinforced concrete buildings or steel framed or
iron framed buildings.
• Near large metallic furniture.
• In a crowd of people or near a building or obstacle.
• In a location exposed to the magnetic field, static
electricity or radio wave interference from radio
communication equipment using the same
frequency band (2.4 GHz) as the AV receiver, such
as a 2.4 GHz wireless LAN device
(IEEE802.11b/g/n) or microwave oven.
• If you live in a heavily populated residential area
(apartment, townhouse, etc.) and if your neighbor’s
microwave oven is placed near your AV receiver,
you may experience radio wave interference. If this
occurs, move your AV receiver to a different place.
When the microwave oven is not in use, there will be
no radio wave interference.

Appendix

Radio Wave Reflections
The radio waves received by the AV receiver include
the radio wave coming directly from the devices and
waves coming from various directions due to
reflections by walls, furniture and building (reflected
waves). The reflected waves (due to obstacles and
reflecting objects) further produce a variety of
reflected waves as well as variation in reception
condition depending on locations. If the audio cannot
be received properly due to this phenomenon, try
moving the location of the wireless LAN device a little.
Also note that audio may be interrupted due to the
reflected waves when a person crosses or
approaches the space between the AV receiver and
the wireless LAN device.
• We assume no responsibility whatsoever for any
damages resulting from the use of this apparatus
except in the cases deemed acceptable under the
applicable laws and regulations.
• Operation in all environment is not guaranteed for
wireless LAN. The communication may not be
possible or have desirable communication speed.

Precautions

■ Electronic device which requires cautions
Hearing aid, pace maker, other medical electronic
devices, fire alarm, automatic door, and other
automatic control device.
When using a pace maker or other medical electronic
devices, confirm with the medical electronic device
maker or dealer for the effect of the radio wave.
The AV receiver contains a microcomputer for
signal processing and control functions. In very rare
situations, severe interference, noise from an
external source, or static electricity may cause it to
lockup. In the unlikely event that this happens,
unplug the power cord from the wall outlet, wait at
least five seconds, and then plug it back in.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused
by the unit’s malfunction. Before you record
important data, make sure that the material will be
recorded correctly.
Before disconnecting the power cord from the wall
outlet, set the AV receiver to standby.

• Do not use this apparatus near an electronic device
handling high-accuracy controls or weak signals.
Doing so may cause an accident due to a
malfunction of the device.
• Do not use this apparatus in use prohibited location
such as an aircraft equipment or a hospital. Doing
so may cause an accident due to a malfunction of
an electronic device or an electro-medical
apparatus. Follow the instructions of the medical
facilities.

En-83

Appendix
DISCLAIMER
Through this device you are able to link to other services or websites which are not under the
control of any company which has designed, manufactured or distributed/have distributed this
device, and its affiliates (collectively, “Company”). We have no control over the nature, content
and availability of those services. The inclusion of any links does not necessarily imply a
recommendation or endorse the views expressed within them.
All information, content and services available through this device belong to third parties and
are protected by copyright, patent, trademark and/or other intellectual property laws of
applicable countries. The information, content and services provided through this device are
for your personal, noncommercial use only. Any information, content or services may not be
used in any manner other than previously approved by the appropriate content owner or
service provider.
You may not modify, copy, republish, translate, exploit, create derivative works, upload, post,
transmit, sell or distribute in any manner any information, content or services available
through this device, unless expressly permitted by the appropriate copyright, patent,
trademark and/or other intellectual property owner, including, without limitation, content owner
or service provider.
THE CONTENT AND SERVICES AVAILABLE THROUGH THIS DEVICE ARE PROVIDED
“AS IS”. COMPANY DOES NOT WARRANT INFORMATION, CONTENT OR SERVICES SO
PROVIDED, EITHER EXPRESSLY OR IMPLIEDLY, FOR ANY PURPOSE.
COMPANY EXPRESSLY DISCLAIMS ANY WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO, WARRANTIES OF TITLE, NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Company makes no representation or warranty of any kind, express or implied, about the
completeness, accuracy, validity, legality, reliability, suitability or availability with respect to
the information, content or services available through this device. Company shall not be liable,
whether in contract or tort, including negligence and strict liability, for any direct, indirect,
special, incidental or consequential damages or any other damages arising out of, or in
connection with, any information contained in, or as a result of the use of any content or
service by you or any third party, even if Company has been advised of the possibility of such
damages, nor shall Company be liable for any third party claims against users of this device
or any third party.
In no event shall Company be responsible nor liable for, without limiting the generality of the
foregoing, any interruption or suspension of any information, content or service available
through this device. Company is neither responsible nor liable for customer service related to
the information, content and services available through this device.
Any question or request for service relating to the information, content or services should be
made directly to the appropriate content owners and services providers.

Video Resolution Chart
The following tables show how video signals at different resolutions are output by
the AV receiver.
✔: Output available
Output HDMI
4K*1

Input
HDMI

Component

1080p/24

1080p

1080i

720p

480p/576p

480i/576i

4K*2

✔*3

1080p/24

✔

1080p

✔

✔*3

1080i

✔

✔*3

720p

✔

✔*3

480p/576p

✔

✔*3

480i/576i

✔

✔*3

480i/576i

✔

✔*3

480i/576i

✔

✔*3

720p

480p/576p

480i/576i

✔*3
✔

1080p
1080i
720p
480p/576p

Composite

Output Component
1080p

Input
HDMI

Composite
1080i

480i/576i

4K*2
1080p/24
1080p
1080i
720p
480p/576p
480i/576i

Component

1080p
1080i
720p
480p/576p
480i/576i

Composite

*1
*2

En-84

480i/576i

✔
✔
✔
✔
✔
✔

Supported resolutions: [3840 × 2160 30 Hz], [3840 × 2160 25 Hz], [3840 × 2160 24 Hz],
[4096 × 2160 24 Hz]
The AV receiver is compatible with HDMI IN 1 to HDMI IN 4. However, the number of the
player that outputs video signal at 4K resolution or the same level at the same time may
be up to three.
Supported resolutions for HDMI OUT SUB.

Appendix

Firmware Update
To update the firmware of the AV receiver, you can
choose from the following two methods: update via
network, or update via USB storage. Choose the one
that best suits your environment. Before proceeding
with the update, please read the corresponding
explanations carefully.
■ Update via network
You need a Internet connection to update the
firmware.
■ Update via USB storage (➔ page 86)
Please prepare a USB storage device such as a
USB flash memory stick. You need at least 32 MB
of available space to update the firmware.

Limitation of liability
The program and accompanying online
documentation are furnished to you for use at your
own risk. Onkyo will not be liable and you will have
no remedy for damages for any claim of any kind
whatsoever concerning your use of the program or
the accompanying online documentation,
regardless of legal theory, and whether arising in
tort or contract. In no event will Onkyo be liable to
you or any third party for any special, indirect,
incidental, or consequential damages of any kind,
including, but not limited to, compensation,
reimbursement or damages on account of the loss
of present or prospective profits, loss of data, or for
any other reason whatsoever.

Before Starting
• Set the “HDMI CEC (RIHD)” setting to “Off”
(➔ page 64).
• Turn off the controller device connected via network.
• Turn off Multi Zone if this function is present.
• Stop playback of contents from Internet Radio, USB
or servers, etc.

Update Procedure

Press RECEIVER followed by HOME on the
remote controller.
The Home menu appears on the TV screen.

Select “Firmware Update” and press ENTER.
Note that the “Firmware Update” option will be
grayed out for a short while after the AV receiver
is turned on. Please wait until it becomes
operable.

Select “Update via NET” and press ENTER.
Note that this option will not be available if there
is no firmware file newer than the currently
installed version. If the AV receiver is not
connected to the internet, “Update via NET” is
not displayed.

Select “Update” and press ENTER.
The update process will begin.
During the update process, the on-screen display
may disappear depending on the updated
program. When this occurs, you can still view the
update progress on the AV receiver’s display.
The on-screen display will reappear after the
update is complete, and upon turning the AV
receiver off and on again.

The message “Completed!” appears on the AV
receiver’s display, indicating that the update
has been completed.

See the Onkyo web site for latest information.
Note
• Check the network connection before updating.
• Do not touch any cable or device connected to the AV
receiver during the update process.
• Do not attempt to access the AV receiver from your PC
while it is being updated.
• Do not shutdown the power of the AV receiver while it is
being updated.
• The storage media in the USB card reader may not work.
• If the USB device is partitioned, each section will be treated
as an independent device.
• If the USB device contains a lot of data, the AV receiver
may take a while to read it.
• Operation is not guaranteed for all USB devices, which
includes the ability to power them.
• Onkyo takes no responsibility whatsoever for the loss or
damage of data resulting from the use of a USB device with
the AV receiver. Onkyo recommends that you back up your
important music files beforehand.
• If you connect a USB hard disk drive to the USB port,
Onkyo recommends that you use its AC adapter to power it.
• USB hubs and USB devices with hub functions are not
supported. Do not connect your USB device via a USB hub.
• USB devices with security functions are not supported.

Updating the Firmware via Network
The AV receiver allows you to update the firmware using
network connection.
Note
• Make sure your AV receiver and TV are turned on and the
AV receiver is connected to the Internet.
• Never unplug or turn off the AV receiver while it is being
updated.
• Never plug or unplug an HDMI or Ethernet cable during the
update process.
• Do not attempt to access the AV receiver from your PC
while it is being updated.
• Never unplug the power cord during the update process.
• It takes up to 20 minutes to complete the firmware update.
• The AV receiver will retain all your settings after the update
is finished.

En-85

Operating
procedure
(➔ page 52)

Appendix

Press 8ON/STANDBY on the front panel.
The AV receiver will enter standby mode.
Do not use 8RECEIVER on the remote
controller.
The AV receiver will enter standby mode
automatically in 3 minutes regardless of whether
8ON/STANDBY is pressed.
Congratulations! You now have the latest
firmware installed on your Onkyo AV receiver.

Troubleshooting
Case 1:
If an error occurs, “Error!! *-**” is displayed on the AV
receiver’s display. (Alpha-numeric characters on the
front display are denoted by asterisks.) Refer to the
following table and take appropriate action.
■ Errors during an update via network
Error Code

Description

*-01, *-10

The Ethernet cable was not detected.
Reconnect the cable properly.

*-02, *-03,

Internet connection error.
Check the following items:
• Make sure the IP address, subnet mask,
gateway address, and DNS server are
configured properly.
• Make sure the router is turned on.
• Make sure the AV receiver and the router
are connected with an Ethernet cable.
• Make sure your router is configured
properly. See the instruction manual of
the router.
• If your network allows only one client
connection and there is any other device
already connected, the AV receiver will
not be able to access the network.
Consult your Internet Service Provider
(ISP).
• If your modem does not function as a
router, you will need a router. Depending
on your network, you may need to
configure the proxy server if necessary.
See the document provided by your ISP.
If you are still unable to access the
Internet, the DNS or proxy server may be
temporarily down. Contact your ISP.

*-04, *-05,
*-06, *-11,
*-13, *-14,
*-16, *-17,
*-18, *-20,
*-21

Others

Retry the update procedure from the
beginning. If the error persists, please
contact Onkyo Support and provide the
error code.

En-86

Case 2:
If an error occurs during the update process,
disconnect then reconnect the AC power cord and try
again.
Case 3:
If you do not have an Internet connection to the
network, please contact Onkyo Support.

Updating the Firmware via USB
The AV receiver allows you to update the firmware
using a USB device.
Note
• Never unplug or turn off the AV receiver during the update
process.
• Never plug or unplug an HDMI cable or a USB device
during the update process.
• Never unplug the USB storage device containing the
firmware file or the AC power cord during the update
process.
• Do not attempt to access the AV receiver from your PC
while it is being updated.
• It takes up to 20 minutes to complete the firmware update.
• The AV receiver will retain all your settings after the update
is finished.

Operating
procedure
(➔ page 52)

Appendix

Update Procedure

Connect a USB device to your PC. If there is
any data in the USB device, remove it first.

Download the firmware file from the Onkyo
web site. The file name is as follows:
ONKAVR****_************.zip

Unzip the downloaded file. The numbers of
folders and files differ according to the model.

Copy all the extracted folders including all
folders and files to the root folder of the USB
device. Be careful not to copy the zip file.

Remove the USB device from your PC and
connect it to the USB port on the AV receiver.

Make sure the AV receiver and TV are turned
on.
If the AV receiver is in standby mode, press
8ON/STANDBY on the AV receiver to light up
the front display.

Select the USB input source.
“Now Initializing...” appears on the AV receiver’s
display and then the name of the USB device is
displayed. It takes 20 to 30 seconds to recognize
the USB device.

Press RECEIVER followed by HOME on the
remote controller.
The Home menu appears on the TV screen.

Select “Firmware Update” and press ENTER.

Select “Update via USB” and press ENTER.
Note that this option will not be available if there
is no firmware file newer than the currently
installed version. If the AV receiver is not
connected to the internet, “Update via USB” is
not displayed.

11
12

Description

*-01, *-10

The message “Completed!” appears on the AV
receiver’s display, indicating that the update
has been completed.
Remove the USB device.

The USB device was not detected. Make
sure the USB flash memory or USB cable is
properly connected to the USB port. If the
USB storage device has its own power
supply, use it to power the USB device.

*-05, *-13,

The firmware file was not found in the root
folder of the USB device, or the firmware
file is for another model. Retry and
download the file on the support page of
the web site, following the on-site
instructions. If the error persists, please
contact Onkyo Support and provide the
error code.

Others

En-87

*-20, *-21

Retry the update procedure from the
beginning. If the error persists, please
contact Onkyo Support and provide the
error code.

Case 2:
If an error occurs during the update process,
disconnect then reconnect the AC power cord and try
again.

Operating
procedure
(➔ page 52)

Appendix

About HDMI
Designed to meet the increased demands of digital
TV, HDMI (High Definition Multimedia Interface) is a
new digital interface standard for connecting TVs,
projectors, Blu-ray Disc/DVD players, set-top boxes,
and other video components. Until now, several
separate video and audio cables have been required
to connect AV components. With HDMI, a single
cable can carry control signals, digital video, and up
to eight channels of digital audio (2-channel PCM,
multichannel digital audio, and multichannel PCM).
The HDMI video stream (i.e., video signal) is
compatible with DVI (Digital Visual Interface)*1, so
TVs and displays with a DVI input can be connected
by using an HDMI-to-DVI adapter cable. (This may
not work with some TVs and displays, resulting in no
picture.)
The AV receiver uses HDCP (High-bandwidth Digital
Content Protection)*2, so only HDCP-compatible
components can display the picture.

Supported Audio Formats
• 2-channel linear PCM (32–192 kHz, 16/20/24 bit)
• Multichannel linear PCM (up to 7.1 ch, 32–192 kHz,
16/20/24 bit)
• Bitstream (DSD, Dolby Digital, Dolby Digital Plus,
Dolby TrueHD, DTS, DTS-HD High Resolution
Audio, DTS-HD Master Audio)
Your Blu-ray Disc/DVD player must also support
HDMI output of the above audio formats.

About Copyright Protection
The AV receiver supports HDCP (High-bandwidth
Digital Content Protection)*2, a copy-protection
system for digital video signals. Other devices
connected to the AV receiver via HDMI must also
support HDCP.

*1
*2

The AV receiver’s HDMI interface is based on the
following:
Audio Return Channel, 3D, x.v.Color, DeepColor, Lip
Sync, 4K (up-scaling and Passthrough), DTS-HD
Master Audio, DTS-HD High Resolution Audio, Dolby
TrueHD, Dolby Digital Plus, DSD and Multichannel
PCM.

DVI (Digital Visual Interface): The digital display interface
standard set by the DDWG*3 in 1999.
HDCP (High-bandwidth Digital Content Protection): The
video encryption technology developed by Intel for
HDMI/DVI. It’s designed to protect video content and
requires a HDCP-compatible device to display the
encrypted video.
DDWG (Digital Display Working Group): Lead by Intel,
Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and
Silicon Image, this open industry group’s objective is to
address the industry’s requirements for a digital
connectivity specification for high-performance PCs and
digital displays.

Note
• The HDMI video stream is compatible with DVI (Digital
Visual Interface), so TVs and displays with a DVI input can
be connected by using an HDMI-to-DVI adapter cable.
(Note that DVI connections only carry video, so you’ll need
to make a separate connection for audio.) However,
reliable operation with such an adapter is not guaranteed.
In addition, video signals from a PC are not supported.
• The HDMI audio signal (sampling rate, bit length, etc.) may
be restricted by the connected source component. If the
picture is poor or there’s no sound from a component
connected via HDMI, check its setup. Refer to the
connected component’s instruction manual for details.

En-88

Appendix

Network/USB Features
Network Requirements
■ Ethernet Network
For the best results, a 100Base-TX switched Ethernet
network is recommended. Although it’s possible to
play music on a computer that’s connected to the
network wirelessly, playback may be unreliable, so it
is recommended to use wired connections.
■ Ethernet Router
A router manages the network, data-routing and
supplying of IP addresses. Your router must support
the following:
• NAT (Network Address Translation). NAT allows
several networked computers to access the Internet
simultaneously via a single Internet connection. The
AV receiver needs Internet access for Internet radio.
• DHCP (Dynamic Host Configuration Protocol).
DHCP supplies IP addresses to the network
devices, allowing them to configure themselves
automatically.
• A router with a built-in 100Base-TX switch is
recommended.
Some routers have a built-in modem, and some
Internet Service Providers (ISP) require you to use
specific routers. Please consult your ISP or computer
dealer if you’re unsure.
■ CAT5 Ethernet cable
Use a shielded CAT5 Ethernet cable (straight-type) to
connect the AV receiver to your home network.
■ Internet Access (for Internet radio)
To receive Internet radio, your Ethernet network must
have Internet access. A narrowband Internet
connection (e.g., 56K modem, ISDN) will not provide
satisfactory results, so a broadband connection is
strongly recommended (e.g., cable modem, xDSL

modem, etc.). Please consult your ISP or computer
dealer if you’re unsure.
Note
• To receive Internet radio with the AV receiver, your
broadband Internet connection must be working and able to
access the Web. Consult your ISP if you have any problems
with your Internet connection.
• The AV receiver uses DHCP to configure its network
settings automatically. If you want to configure these
settings manually, see “Network” (➔ page 67).
• The AV receiver does not support PPPoE settings, so if you
have a PPPoE-type Internet connection, you must use a
PPPoE-compatible router.
• Depending on your ISP, you may need to specify a proxy
server to use Internet radio. If your computer is configured
to use a proxy server, use the same settings for the AV
receiver (➔ page 67).

Server Requirements
■ Server playback
The AV receiver can play digital music files stored on
a computer or media server and supports the
following technologies:
• Windows Media Player 11
• Windows Media Player 12
• DLNA-certified media server
• The computer or media server must be on the same
network as the AV receiver.
• Up to 20,000 folders can be displayed, and folders
may be nested up to 16 levels deep.
Note
• Depending on the media server, the AV receiver may not
recognize it, or may not be able to play its music files.

■ Remote playback
• Windows Media Player 12
• DLNA-certified (within DLNA Interoperability
Guidelines version 1.5) media server or controller
device.

En-89

The setting varies depending on the media server or
controller devices. Refer to your devices’ instruction
manual for details.
If the operating system of your personal computer is
Windows 8/Windows 7, Windows Media Player 12 is
already installed. For more information, see the
Microsoft web site.

USB Device Requirements
• USB mass storage device class (but not always
guaranteed).
• FAT16 or FAT32 file system format.
• If the storage device has been partitioned, each
section will be treated as an independent device.
• Up to 20,000 folders can be displayed, and folders
may be nested up to 16 levels deep.
• USB hubs and USB devices with hub functions are
not supported.
Note
• If the media you connect is not supported, the message “No
Storage” will be displayed.
• If you connect a USB hard disk drive to the AV receiver’s
USB port, we recommend that you use its AC adapter to
power it.
• The AV receiver supports USB MP3 players that support
the USB Mass Storage Class standard, which allows USB
devices to be connected to computers without the need for
special drivers or software. Note that not all USB MP3
players support the USB Mass Storage Class standard.
Refer to your USB MP3 player’s instruction manual for
details.
• Protected WMA music files on an MP3 player cannot be
played.
• Onkyo accepts no responsibility whatsoever for the loss or
damage to data stored on a USB device when that device
is used with the AV receiver. We recommend that you back
up your important music files beforehand.
• MP3 players containing music files that are managed with
special music software are not supported.

Appendix
• Operation is not guaranteed for all USB devices, which
includes the ability to power them.
• Do not connect your USB device via a USB hub. The USB
device must be connected directly to the AV receiver’s USB
port.
• If the USB device contains a lot of data, the AV receiver
make take a while to read it.
• USB devices with security functions cannot be played.

Supported Audio File Formats
For server playback and playback from a USB device,
the AV receiver supports the following music file
formats.
Variable bit-rate (VBR) files are supported. However,
playback times may not display correctly.
Note
• With remote playback, the AV receiver does not support the
following music file formats: FLAC, Ogg Vorbis, DSD and
Dolby TrueHD.
• In the case of server playback, the above-mentioned file
formats may not be played depending on the server type.

■ MP3 (.mp3 or .MP3)
• MP3 files must be MPEG-1/MPEG-2 Audio Layer 3
format with sampling rates of 8 kHz, 11.025 kHz,
12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz,
44.1 kHz, 48 kHz and bitrates of between 8 kbps
and 320 kbps. Incompatible files cannot be played.
■ WMA (.wma or .WMA)
WMA stands for Windows Media Audio and is an
audio compression technology developed by
Microsoft Corporation. Audio can be encoded in WMA
format by using Windows Media® Player.
• WMA files must have the copyright option turned off.
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz, bitrates of between 5 kbps and 320 kbps,
and WMA DRM are supported.
• WMA Pro/Voice formats are not supported.

■ WMA Lossless (.wma or .WMA)
• Sampling rates of 44.1 kHz, 48 kHz, 88.2 kHz,
96 kHz are supported.
• Quantization bit: 16 bit, 24 bit
■ WAV (.wav or .WAV)
WAV files contain uncompressed PCM digital audio.
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz, 64 kHz, 88.2 kHz, 96 kHz, 176.4 kHz and
192 kHz are supported.
• Quantization bit: 8 bit, 16 bit, 24 bit
*

For playback from a USB device, sampling rates of
176.4 kHz and 192 kHz are not supported.

■ AAC
(.aac/.m4a/.mp4/.3gp/.3g2/.AAC/.M4A/.MP4/
.3GP or .3G2)
AAC stands for MPEG-2/MPEG-4 Audio.
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz, 64 kHz, 88.2 kHz, 96 kHz and bitrates of
between 8 kbps and 320 kbps are supported.
■ FLAC (.flac or .FLAC)
FLAC is a file format for lossless audio data
compression.
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz, 64 kHz, 88.2 kHz, 96 kHz, 176.4 kHz and
192 kHz are supported.
• Quantization bit: 8 bit, 16 bit, 24 bit
■ Ogg Vorbis (.ogg or .OGG)
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz and bitrates of between 48 kbps and
500 kbps are supported. Incompatible files cannot
be played.

En-90

■ LPCM (Linear PCM)
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz, 64 kHz, 88.2 kHz and 96 kHz are
supported.
• Quantization bit: 8 bit, 16 bit, 24 bit
*

Only for playback via network.

■ Apple Lossless (.m4a/.mp4/.M4A/.MP4)
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz, 64 kHz, 88.2 kHz and 96 kHz are
supported.
• Quantization bit: 16 bit, 24 bit
■ DSD (.dsf or .DSF)
• The sampling rate of 2.8224 MHz is supported.
■ Dolby TrueHD (.vr/.mlp/.VR/.MLP)
• Sampling rates of 48 kHz, 64 kHz, 88.2 kHz,
96 kHz, 176.4 kHz and 192 kHz are supported.
*

For playback from a USB device, sampling rates only of
48 kHz and 64 kHz are supported.

About DLNA
The Digital Living Network Alliance is an international,
cross-industry collaboration. Members of DLNA
develop a concept of wired and wireless interoperable
networks where digital content such as photos,
music, and videos can be shared through consumer
electronics, personal computers, and mobile devices
in and beyond the home. The AV receiver complies
with the DLNA Interoperability Guidelines version 1.5.

Appendix

License and Trademark
Information
“x.v.Color” is a trademark of Sony Corporation.

Manufactured under license under U.S. Patent Nos:
5,956,674; 5,974,380; 6,226,616; 6,487,535; 7,212,872;
7,333,929; 7,392,195; 7,272,567 & other U.S. and
worldwide patents issued & pending. DTS-HD, the Symbol,
& DTS-HD and the Symbol together are registered
trademarks & DTS-HD Master Audio is a trademark of
DTS, Inc. Product includes software. © DTS, Inc. All Rights
Reserved.

Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic and the double-D symbol are trademarks
of Dolby Laboratories.
Music Optimizer™ and “WRAT” are trademarks of Onkyo
Corporation.

“The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are trademarks or registered
trademarks of HDMI Licensing LLC in the United States
and other countries.”

InstaPrevue and the InstaPrevue logo are trademarks or
registered trademarks of Silicon Image, Inc. in the United
States and other countries.

“MHL, the MHL Logo, and Mobile High-Definition Link are
trademarks or registered trademarks of MHL LLC in the
United States and other counties.”

Apple, iPod and iPhone are trademarks of Apple Inc.,
registered in the U.S. and other countries.
Apple TV is a trademark of Apple Inc., registered in the
U.S. and other countries.

Manufactured under license from
Audyssey Laboratories™,Inc. U.S. and foreign patents
pending. Audyssey MultEQ®, Audyssey Dynamic EQ® and
Audyssey Dynamic Volume® are registered trademarks of
Audyssey Laboratories,Inc.
“DLNA®, the DLNA Logo and DLNA CERTIFIED® are
trademarks, service marks, or certification marks of the
Digital Living Network Alliance.”
MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
This product is protected by certain intellectual property
rights of Microsoft. Use or distribution of such technology
outside of this product is prohibited without a license from
Microsoft.
Windows and the Windows logo are trademarks of the
Microsoft group of companies.
Qdeo and QuietVideo are trademarks of Marvell or its
affiliates.

En-91

The Wi-Fi CERTIFIED Logo is a certification mark of the
Wi-Fi Alliance.
Wi-Fi certified logo shows international association
certifying interoperability “Wi-Fi Alliance” ensures the
product has passed the test for compatibility with other
Wi-Fi certified equipment.

The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by Onkyo is under license. Other trademarks
and trade names are those of their respective owners.
Onkyo does not guarantee Bluetooth compatibility between
the AV receiver and all Bluetooth-enabled devices.
For compatibility between the AV receiver and another
device with Bluetooth technology, consult the device’s
documentation and dealer. In some countries, there may
be restrictions on using Bluetooth devices. Check with your
local authorities.

Appendix

Specifications
Amplifier Section
Rated Output Power
All channels:

95 watts minimum continuous power
per channel, 8 ohm loads, 2 channels
driven from 20 Hz to 20 kHz, with a
maximum total harmonic distortion of
0.08% (FTC)
115 watts minimum continuous power
per channel, 6 ohm loads, 2 channels
driven at 1 kHz, with a maximum total
harmonic distortion of 0.7% (FTC)
(North American)
7 ch × 160 W at 6 ohms, 1 kHz, 1 ch
driven of 1% (IEC)
(Others)
Maximum Effective Output Power
7 ch × 175 W at 6 ohms, 1 kHz, 1 ch
driven (JEITA)
(Asian)
Dynamic Power*
* IEC60268-Short-term maximum output power
240 W (3 Ω, Front)
210 W (4 Ω, Front)
120 W (8 Ω, Front)
THD+N (Total Harmonic Distortion+Noise)
0.08% (20 Hz - 20 kHz, half power)
Damping Factor
60 (Front, 1 kHz, 8 Ω)
Input Sensitivity and Impedance (Unbalance)
200 mV/47 kΩ (LINE)
2.5 mV/47 kΩ (PHONO MM)
Rated RCA Output Level and Impedance
200 mV/2.2 kΩ (LINE OUT)
Maximum RCA Output Level and Impedance
2 V/2.2 kΩ (LINE OUT)
Phono Overload
70 mV (MM 1 kHz 0.5% Direct)
Frequency Response 5 Hz - 100 kHz/+1 dB, –3 dB (Direct
mode)
Tone Control Characteristics
±10 dB, 30 Hz (BASS)
±10 dB, 20 kHz (TREBLE)
Signal to Noise Ratio 106 dB (LINE, IHF-A)
80 dB (PHONO MM, IHF-A)

Speaker Impedance

6 Ω - 16 Ω
(North American and Taiwanese)
4 Ω - 16 Ω (Others)

Video Section
Input Sensitivity/Output Level and Impedance
1 Vp-p/75 Ω (Component Y)
0.7 Vp-p/75 Ω (Component PB/CB,
PR/CR)
1 Vp-p/75 Ω (Composite)
Component Video Frequency Response
5 Hz - 100 MHz/+0 dB, –3 dB

Tuner Section
FM Tuning Frequency Range
87.5 MHz - 107.9 MHz
(North American and Taiwanese)
87.5 MHz - 108.0 MHz, RDS (Others)
AM Tuning Frequency Range
522/530 kHz - 1611/1710 kHz
Preset Channel
40

Network Section
Ethernet LAN
10BASE-T/100BASE-TX
Wireless LAN
Compatible standards:
IEEE 802.11 b/g/n standard (Wi-Fi®
standard)
Security:
WEP 64 bit, WEP 128 bit, WPA/WPA2PSK (AES), WPA/WPA2-PSK (TKIP)
Transmission frequency
1 - 11 ch (North American and
Taiwanese)
10 - 13 ch (France)
1 - 13 ch (Others)
(Wi-Fi® standard)
Radio frequency
2.4 GHz

En-92

Bluetooth Section
Communication system
Bluetooth Specification version 2.1 +
EDR (Enhanced Data Rate)
Maximum communication range
Line of sight approx. 15 m*1
Frequency band
2.4 GHz band (2.4000 GHz 2.4835 GHz)
Modulation method
FHSS (Freq Hopping Spread Spectrum)
Compatible Bluetooth profiles
A2DP 1.2 (Advanced Audio Distribution
Profile)
AVRCP 1.3 (Audio Video Remote
Control Profile)
Supported Codecs
SBC
Transmission range (A2DP)
20 Hz - 20,000 Hz (Sampling frequency
44.1 kHz)
*1

The actual range will vary depending on factors such as
obstacles between devices, magnetic fields around a
microwave oven, static electricity, cordless phone,
reception sensitivity, antenna’s performance, operating
system, software application, etc.

Appendix
■ Audio Outputs

General
Power Supply

AC 120 V, 60 Hz
(North American and Taiwanese)
AC 220 - 240 V, 50/60 Hz (Others)
Power Consumption 6.3 A (North American and Taiwanese)
600 W (Others)
No-sound Power Consumption
85 W (North American and Taiwanese)
70 W (European and Australian)
70 W (230 V)
80 W (240 V)
(Others)
Stand-by Power Consumption
0.15 W (North American and Taiwanese)
0.2 W (Others)
Dimensions (W × H × D)
435 mm × 173.5 mm × 328 mm
17-1/8" × 6-13/16" × 12-15/16"
Weight
9.8 kg (21.6 lbs.)
(North American and Taiwanese)
10.0 kg (22.0 lbs.) (Others)

Analog
ZONE2 LINE OUT
Subwoofer Pre Outputs
2
Speaker Outputs
Main (L, R, C, SL, SR, SBL/FHL,
SBR/FHR) + ZONE2 (L, R)
Phones
1 (ø 6.3)

■ Others
Setup Mic
RI
USB
Ethernet

1
1
1 (Front)
1

Specifications and features are subject to change
without notice.

■ HDMI
Input
Output
Video Resolution
Audio Format
Supported

IN 1, IN 2, IN 3, IN 4, IN 5, IN 6
OUT MAIN, OUT SUB
4K
Dolby TrueHD, DTS-HD Master Audio,
DVD-Audio, DSD
3D, Audio Return Channel, DeepColor,
x.v.Color, LipSync, CEC (RIHD), 4K (upscaling and Passthrough)

■ Video Inputs
Component
Composite

IN
BD/DVD, CBL/SAT, GAME, PC, AUX

■ Video Outputs
Component
Composite

OUT
MONITOR OUT

■ Audio Inputs
Digital
Analog

Optical: 1
Coaxial: 2
BD/DVD, CBL/SAT, GAME, PC, TV/CD,
PHONO, AUX

En-93

Appendix

Memo

En-94

Appendix

Memo

En-95

2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
http://www.onkyo.com/
The Americas
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
For Dealer, Service, Order and all other Business Inquiries:
Tel: 201-785-2600 Fax: 201-785-2650
http://www.us.onkyo.com/
For Product Support Team Only:
1-800-229-1687
http://www.us.onkyo.com/
Europe
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4208-213
http://www.eu.onkyo.com/
Unit 19, Building 6, Croxley Green Business Park, Hatters Lane, Watford, WD18 8YH, UK
Tel: +44 (0)8712-00-19-96 Fax: +44 (0)8712-00-19-95
China

(Hong Kong)
Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.
Tel: 852-2429-3118 Fax: 852-2428-9039
http://www.hk.onkyo.com/

(Mainland)
1301, 555 Tower, No.555 West NanJing Road, Jing’an District, Shanghai, China 200041,
Tel: 86-21-52131366 Fax: 86-21-52130396
http://www.cn.onkyo.com/
Asia, Oceania, Middle East, Africa
Please contact an Onkyo distributor referring to Onkyo SUPPORT site.
http://www.intl.onkyo.com/support/
The above-mentioned information is subject to change without prior notice.
Visit the Onkyo web site for the latest update.
Y1303-3
SN 29401412EN-B
(C) Copyright 2013 Onkyo Corporation Japan. All rights reserved.

* 2 9 4 0 1 4 1 2 E N - B *

Using Internet Radio

Using Internet Radio
Common Procedures in Internet Radio
Menu
Note
• Available services may vary depending on the region.
• Certain network service or contents available through this
device may not be accessible in case the service provider
terminates its service.

Press NET.
A list of the network services appears, and the
NET indicator lights. If it flashes, verify that the
Ethernet cable is firmly connected to the AV
receiver.
Select the desired service and press ENTER.
The top page of the selected service appears.

Using Multiple Accounts
The AV receiver supports multiple user accounts,
which means you can freely switch between several
logins. After registering user accounts, login is
performed from the “Users” screen.

Pandora® internet radio
–Getting Started (U.S. only)..................... 2

Using Rhapsody (U.S. only).......................... 3

Press MENU while the Users screen is
displayed.
The following menu items appear:
Add new user:
Remove this user:
You can either store a new user account, or
delete an existing one.

Using the SiriusXM Internet Radio
(North American only).............................. 4

Using Last.fm Internet Radio ........................ 5

Tip
• Some of the services don’t allow the use of multiple user
accounts.
• You can store up to 10 user accounts.
• To switch between accounts you must first log out from the
current account, and log in again on the “Users” screen.

En-1

Using Slacker Personal Radio ...................... 6

Using MP3tunes ............................................. 7

Using Internet Radio

Pandora® internet radio
–Getting Started (U.S. only)
Pandora is a free, personalized Internet radio service
that plays the music you know and helps you discover
music you’ll love.

Use q/w to select “I have a Pandora Account”
or “I’m new to Pandora” and then press
ENTER.
If you are new to Pandora select “I’m new to
Pandora”. You will see an activation code on
your TV screen. Please write down this code. Go
to an Internet connected computer and point your
browser to www.pandora.com/onkyo
Enter your activation code and then follow the
instructions to create your Pandora account and
your personalized Pandora Internet radio
stations. You can create your stations by entering
your favorite tracks and artists when prompted.
After you have created your account and stations
you can return to your Onkyo receiver and press
enter to begin listening to your personalized
Pandora Internet radio.
If you have an existing Pandora account, you can
add your Pandora account to your Onkyo
receiver by selecting “I have a Pandora
Account” and logging in with your email and
password.

To play a station, use q/w to select the station
from your station list, and then press ENTER.
Playback starts and the playback screen
appears.
Create a New Station:
Enter the name of a track, artist, or genre and
Pandora will create a unique radio station for you
based on the musical qualities of that track, artist,
or genre.
■ Menu Items
I like this track:
Give a track “thumbs-up” and Pandora will play
more music like it.
I don’t like this track:
Give a track “thumbs-down” and Pandora will ban
that track from the current station.
Why is this track playing?:
Discover some of the musical attributes that
Pandora uses to create your personal radio
stations.
I’m tired of this track:
If you are tired of a track, you can put the track to
sleep and Pandora will not play it for one month.
Create station from this artist:
Creates a radio station from this artist.

Tip
• If you want to use multiple user accounts, see “Using
Multiple Accounts” (➔ page 1). Login can be made
from the “Users” screen.

En-2

Delete this station:
This will permanently delete a station from your
Pandora account. All of your thumbs feedback
will be lost should you choose to re-create the
station with the same track or artist.
Create station from this track:
Creates a radio station from this track.
Rename this station:
Lets you rename the current radio station.
Bookmark this artist:
Pandora will bookmark your favorite artist for
your profile on www.pandora.com.
Bookmark this track:
Pandora will bookmark the current track and
allow you to buy them all from Amazon or iTunes
in one step!
Add to My Favorites:
Adds a station to My Favorites list.

PANDORA, the PANDORA logo, and the Pandora
trade dress are trademarks or registered trademarks
of Pandora Media, Inc. Used with permission.

Using Internet Radio

Using Rhapsody (U.S. only)

Use q/w to select “Sign in to your account”
and then press ENTER.
To use Rhapsody, you need an account. If you
don’t have one yet, you can create a new
account at
www.rhapsody.com/onkyo
If you have an existing Rhapsody account, select
“Sign in to your account” and press ENTER.
Enter your user name (usually your email) and
password in the next keyboard screen, or in Web
Setup.
■ Using the keyboard screen
1. Use q/w/e/r and ENTER to enter your user
name and password.
2. Select “OK”.
3. Press ENTER. The “Confirm your entries”
screen appears.
4. Press ENTER.
Tip

Use q/w to select the menu, then press
ENTER.
Search:
You can search for music by Artist, Album, or
Track.
Music Guide:
You can play tracks from Genres, Top Artists,
Top Albums, Top Tracks, New Releases, and
Staff Picks.
Rhapsody Channels:
Listen to radio channels programmed by
Rhapsody’s top-notch editors.
Playlists:
Play your own personal playlists.
My Library:
Bookmark your favorite albums and tracks from
the Rhapsody catalog using My Library.
Account Info:
Confirm your account information.
Sign Out:
Sign out from your Rhapsody account.

• If you want to use multiple user accounts, see “Using
Multiple Accounts” (➔ page 1). Login can be made
from the “Users” screen.

Use q/w to select a channel, and press ENTER
or 1 to start playback.
Playback starts and the playback screen
appears.
You can control the tracks with the buttons on the
remote control.
Enabled buttons: 1, 3, 2, 5, 4, 7,
6, RANDOM, REPEAT
Note
• On Rhapsody Channels, some of the buttons don’t
work.

■ Menu Items
Add track to My Library:
Bookmark currently-playing tracks.
Add album to My Library:
Bookmark currently-playing albums.
Add playlist to My Library:
Bookmark currently-playing playlists.
Add channel to My Channels:
Bookmark currently-playing Rhapsody radio
channels.
Add to My Favorites:
Adds a track, channel or playlist to My Favorites
list.
Tip
• You can remove bookmarked tracks, albums, and
Rhapsody Channels from My Library.

En-3

Using Internet Radio

Using the SiriusXM Internet Radio
(North American only)

Your Onkyo AV receiver includes a free trial of
SiriusXM Internet Radio. The “Account Info” screen
shows how many days are left in your trial. After the
trial period expires, if you want to continue listening to
the service, you must subscribe. To subscribe go to
www.siriusxm.com/internetradio with your
computer.

Use q/w to select “Sign In”, and then press
ENTER.
If you have an existing SIRIUS account, you can
sign in by selecting “Sign In”. Enter your user
name and password in the next keyboard screen,
or in Web Setup. If you don’t know your
username or password, call Sirius XM at (888)
539-7474 for assistance.
Tip
• If you want to use multiple user accounts, see “Using
Multiple Accounts” (➔ page 1). Login can be made
from the “Users” screen.

When you subscribe, you will be provided with a
username and password which has to be entered into
the AV receiver.

■ Using the keyboard screen
1. Use q/w/e/r and ENTER to enter your user
name and password.
2. Select “OK”.
3. Press ENTER. The “Confirm your entries”
screen appears.
4. Press ENTER.
“Please wait...” appears and then “SiriusXM
Internet Radio” screen appears which displays
the category available for selection.

To use SiriusXM Internet Radio, you must have your
AV receiver connected to the Internet. Using the
remote control, follow these steps:

Use q/w to select the category and then press
ENTER.
The channel list screen for the selected category
appears.

En-4

Use q/w to select the desired channel and then
press ENTER.
The playback screen for the selected channel
appears and you can listen to SiriusXM Internet
Radio.
You can control the tracks with the buttons on the
remote control.
Enabled buttons: 2, 3, 7, 6
■ Menu Items
Add to My Favorites:
Adds a channel to My Favorites list.

SiriusXM Internet Radio subscriptions are sold
separately and are governed by the Sirius Terms and
Conditions (see www.sirius.com). Be sure to read this
agreement before you purchase your subscription.
Sirius, XM and all related marks and logos are
trademarks of Sirius XM Radio Inc. and its
subsidiaries. All rights reserved.

Using Internet Radio

Using Last.fm Internet Radio

Last.fm is a music service that learns what you
love...
Your new Onkyo AV receiver is very clever. If you
have a free Last.fm account, it will keep track of all
the songs you’ve just played. When you visit the
Last.fm website, you can see personal charts of the
music you’ve enjoyed, share them with friends and
see what they like, too.

■ Using the keyboard screen
1. Use q/w/e/r and the ENTER to enter your
user name and password.
2. Select “OK”.
3. Press ENTER. The “Confirm your entries”
screen appears.
4. Press ENTER.
“Please wait...” appears and then “Last.fm
Internet Radio” screen appears.

With thousands of biographies, reviews and an
endless choice of personalised, ad-free radio
stations, Last.fm is a great way to discover music.
Pick up your free Last.fm account today at
www.last.fm/join
Get a subscription and you can enjoy the best of adfree Last.fm Radio on your Onkyo AV receiver without
a computer!
Recommended Radio:
Discover smart personalised recommendations that
adapt as your tastes change.
Artist Radio:
Pick any artist and we’ll play you a whole station of
music inspired by your choice.
My Library:
Sit back and enjoy selections from all the music
you’ve heard since you joined Last.fm.
Tag Radio:
Polish funk? Death pop? Think of a style and we’ll
entertain you with it for hours.
Start your free trial straight away when you create
your account and see for yourself what it’s like to
have the world’s music at your fingertips. Latest
prices and full information are available at
www.last.fm/subscribe

Profile:
You can play tracks from “Recently Listened
Tracks”, “Library” and “Neighbours”.
Account Info:
Confirm your account information.
Sign Out:
It signs out from your account.

Use q/w to select “Sign in to your account”,
and then press ENTER.
If you have the existing Last.fm account, you can
sign in to your account to select “Sign in to your
account”. Enter your user name and password in
the next keyboard screen.

■ Menu Items
I Love this track:
Track information is saved in Last.fm server, and
playback frequency increases.
Ban this track:
Track information is saved in Last.fm server, and
playback frequency reduces.
Add to My Favorites:
Adds a station to My Favorites list.

Tip
• If you want to use multiple user accounts, see “Using
Multiple Accounts” (➔ page 1). Login can be made
from the “Users” screen.

Use q/w to select menu and then press
ENTER.
Search Station:
You can search station by Artist, Tag, or User
Name.
Top Artists Station:
You can play tracks of top-rated artists.
Top Tags Station:
You can play tracks of top-rated tags.
Personal Station:
• You can play tracks from personalized station
(“Your Library”, “Your Neighbourhood” and
“Your Recommendations”).

En-5

Use q/w to select a station, and press ENTER
or 1 to start playback.
Playback starts and the playback screen
appears.

■ Using scrobbling control
Use q/w to select “Enable”, and then press ENTER.
*

Internet radio services provided by a third party may be
terminated with or without notice.
Internet radio services may not be available in some areas.

Using Internet Radio

Using Slacker Personal Radio

If you do not have an account, create one on
the Slacker website (www.slacker.com) with
your computer.
If you already have a Slacker account, select
“Sign in to your account” and then press
ENTER.
The keyboard screen appears. You can enter
information from the remote control or the keys
on the main unit.

If there are no mistakes in the information you
have entered, use q/w/e/r to select “OK”
then press ENTER.
An account information confirmation screen
appears.

If you do not have an account, select “Access
without Sign In” and press ENTER to use a
restricted version of the service.
Note that use will be restricted.
Tip
• If you want to use multiple user accounts, see “Using
Multiple Accounts” (➔ page 1). Login can be made
from the “Users” screen.

Use q/w to select a menu item and then press
ENTER.
To sign out, use q/w to select “Sign out” from
this screen and then press ENTER.

Use q/w to select a station and then press
ENTER or 1 to start playback from the
station.
The playback screen appears.

You can control the tracks with the buttons on
the remote control.
Enabled buttons: 1, 3, 2, 6
■ Menu Items
Rate Song as Favorite:
Stores information to server, making it more likely
that the song will be played again.
Ban Song:
Stores information to server, making it less likely
that the song will be played again.
Ban Artist:
Stores information to server, making it less likely
that the songs from this artist will be played
again.
Mark Favorite:
Adds the currently playing station to your
favorites.
Unmark Favorite:
Deletes the currently playing station from your
favorites.
Add song to Library:
Adds the currently playing track to your library.
Delete song from Library:
Deletes the currently playing track from your
library.
Add to My Favorites:
Adds a station or song to My Favorites list.

En-6

Using Internet Radio

Using MP3tunes
Listen to your music collection on your home stereo in
complete digital fidelity without a personal computer
plus safely backup all your songs. Here’s how:

Playing Contents on the AV Receiver
Tip
• Before proceeding, you need to select the MP3tunes
service as described in “Common Procedures in Internet
Radio Menu” (➔ page 1).

The track at the top of the music list is automatically
played back.

Creating an Account on your Computer

From your computer, open a web browser and
go to: www.mp3tunes.com/signup

2
3

Create an account.

View, edit and listen to your files by clicking
on Player (www.mp3tunes.com/player).

Use q/w to select “Sign in to your account”,
and then press ENTER.

Enter the e-mail address and password you
used when creating your account, select “OK”
and press ENTER.
The keyboard screen appears. You can enter
your user name and password from the remote
controller or the buttons on the AV receiver.

Click the Upload link
(www.mp3tunes.com/upload) to add files to
your Locker.

If there are no mistakes in the information you
have entered, select “OK” and press ENTER.
An account information confirmation screen
appears.
Tip
• If you want to use multiple user accounts, see “Using
Multiple Accounts” (➔ page 1). Login can be made
from the “Users” screen.

Use q/w to select the menu, then press
ENTER.
Music:
The place to find your Artists, Albums, and
Playlists.
Shuffle:
Starts playing a random selection of tracks from
your Locker.
Search:
Find a specific Album, Artist, or Song.
Account Info:
Your MP3tunes account information.
Sign Out:
Log out of your MP3tunes account.

En-7

Use q/w to select a track and press ENTER or
1 to start playback.
A playback screen appears.
You can control the tracks with the buttons on the
remote control.
Enabled buttons: 1, 3, 2, 7, 6
■ Menu Items
Go to Menu:
Displays additional menu options.

You can view or change your MP3tunes
account settings by going to
www.mp3tunes.com/account.

Utilisation d’une webradio

Utilisation d’une
webradio
Procédures courantes dans le menu de
webradio
Remarque
• Les services disponibles peuvent varier en fonction de la
région.
• Certain services réseau ou contenus disponible via cet
appareil peuvent être inaccessibles au cas où le prestataire
de services terminerait son service.

Appuyez sur NET.
Une liste des services réseau s’affiche, et le
témoin NET s’allume. S’il clignote, vérifiez que le
câble Ethernet est fermement branché sur
l’ampli-tuner AV.
Sélectionnez le service désiré et appuyez sur
ENTER.
La page principale du service sélectionné
s’affiche.

Utilisation de plusieurs comptes
L’ampli-tuner AV prend en charge plusieurs comptes
utilisateur, ce qui signifie que vous pouvez librement
commuter entre plusieurs connexions. Après avoir
enregistré des comptes utilisateur, l’identification est
réalisée à partir de l’écran « Users ».

Appuyez sur MENU lorsque l’écran Users est
affiché.
Les éléments de menu suivants s’affichent :
Add new user :
Remove this user :
Vous pouvez soit stocker un nouveau compte
utilisateur, soit en supprimer un existant.

Pandora® internet Radio
–Pour commencer
(États-Unis uniquement).......................... 2
Utilisation de Rhapsody
(Etats-Unis uniquement).......................... 3

Utilisation de SiriusXM Internet Radio
(Amérique du Nord uniquement) ............ 4

Utilisation de la webradio Last.fm................ 5

Conseil
• Certains des services ne permettent pas l’utilisation de
plusieurs comptes utilisateur.
• Vous pouvez stocker jusqu’à 10 comptes utilisateur.
• Pour commuter entre les comptes, vous devez d’abord
vous déconnecter du compte actuel, puis vous reconnectez
depuis l’écran « Users ».

Fr-1

Utilisation de Slacker Personal Radio ......... 6

Utilisation d’une webradio

Pandora® internet Radio
–Pour commencer (États-Unis
uniquement)
Pandora est un service de radio en ligne libre et
personnalisé vous permettant de lire la musique que
vous connaissez et de découvrir celle que vous
aimez.

Utilisez q/w pour sélectionner « I have a
Pandora Account » ou « I’m new to Pandora »,
puis appuyez sur ENTER.
Si vous ne connaissez pas Pandora sélectionnez
« I’m new to Pandora ». Un code d’activation
apparaîtra sur l’écran de votre téléviseur. Notez
ce code. Utilisez un ordinateur branché sur
Internet et connectez le navigateur à
www.pandora.com/onkyo
Saisissez votre code d’activation puis suivez les
instructions pour créer votre compte Pandora et
vos stations webradio Pandora personnalisées.
Lorsque vous y êtes invités, vous pouvez créer
vos stations en saisissant vos pistes et vos
artistes préférés. Après la création de votre
compte et de vos stations, vous pouvez retourner
à votre récepteur Onkyo et appuyez sur entrée
pour écouter votre webradio Pandora
personnalisée.
Si vous disposez d’un compte Pandora, vous
pouvez ajouter votre compte Pandora à votre
récepteur Onkyo en sélectionnant « I have a
Pandora Account » et y accéder en entrant
votre adresse e-mail et votre mot de passe.

Pour lire une station, utilisez q/w pour
sélectionner la station dans votre liste de
stations, puis appuyez sur ENTER.
La lecture débute et l’écran de lecture s’affiche.
Create a New Station :
Saisissez le nom d’une piste, d’un artiste ou d’un
genre et Pandora créera une station radio unique
pour vous en fonction des qualités musicales de
la piste, de l’artiste ou du genre choisi.
■ Eléments du menu
I like this track :
Acceptez la piste et Pandora lira d’autres
musiques similaires.
I don’t like this track :
Rejetez la piste et Pandora éliminera cette piste
de la station écoutée.
Why is this track playing? :
Découvrez certains des attributs musicaux que
Pandora utilise pour créer vos stations radio
personnelles.
I’m tired of this track :
Si vous en avez assez d’une piste, vous pouvez
mettre la piste « au repos » et Pandora ne la lira
plus pendant un mois.
Create station from this artist :
Permet de créer une station radio à partir de cet
artiste.

Conseil
• Si vous souhaitez utiliser plusieurs comptes
utilisateur, consultez « Utilisation de plusieurs
comptes » (➔ page 1). L’identification peut être
réalisée à partir de l’écran « Users ».

Fr-2

Delete this station :
Ceci supprimera de façon permanente la station
de votre compte Pandora. Au cas où vous
décideriez de récréer la station avec les mêmes
pistes ou les mêmes artistes, tous vos
acceptations/rejets précédents seront perdus.
Create station from this track :
Permet de créer une station radio à partir de
cette piste.
Rename this station :
Vous permet de renommer la station radio
actuelle.
Bookmark this artist :
Pandora marquera votre artiste préféré pour
votre profil sur www.pandora.com.
Bookmark this track :
Pandora marquera la piste en cours et vous
permettra de toutes les acheter sur Amazon ou
iTunes en une étape !
Add to My Favorites :
Permet d’ajouter une station à la liste My
Favorites.

PANDORA, le logo PANDORA, et l’habillage
commercial Pandora sont des marques
commerciales ou des marques déposées de la
société Pandora Media, Inc. Utilisées avec
autorisation.

Utilisation d’une webradio

Utilisation de Rhapsody (Etats-Unis
uniquement)

Utilisez q/w pour sélectionner « Sign in to your
account », puis appuyez sur ENTER.
Vous devez posséder un compte pour utiliser
Rhapsody. Si vous ne disposez pas encore d’un
compte, vous pouvez en créer un à partir de
www.rhapsody.com/onkyo
Si vous possédez déjà un compte Rhapsody,
sélectionnez « Sign in to your account », puis
appuyez sur ENTER.
Saisissez votre nom utilisateur (en général votre
adresse électronique) et votre mot de passe dans
l’écran clavier suivant ou dans Configuration
Web.
■ Utilisation de l’écran clavier
1. Utilisez q/w/e/r et ENTER pour saisir votre
nom d’utilisateur et votre mot de passe.
2. Sélectionnez « OK ».
3. Appuyez sur ENTER. L’écran « Confirm
your entries » s’affiche.
4. Appuyez sur ENTER.

Utilisez q/w pour sélectionner le menu, puis
appuyez sur ENTER.
Search :
Vous pouvez rechercher des morceaux par
artiste, par album ou par piste.
Music Guide :
Vous pouvez lire des pistes à partir des
genres,des meilleurs artistes, des meilleurs
albums, des meilleures pistes, des nouveautés et
des sélections du personnel.
Rhapsody Channels :
Écoutez les canaux de radio programmée par les
meilleurs éditeurs de Rhapsody.
Playlists :
Permet de jouer vos listes de lecture
personnelles.
My Library :
Marquez vos albums et vos pistes personnelles
dans le catalogue de Rhapsody à l’aide de My
Library.
Account Info :
Vérifiez les informations de votre compte.
Sign Out :
Déconnectez-vous de votre compte Rhapsody.

Utilisez q/w pour sélectionner un canal, puis
appuyez sur ENTER ou 1 pour démarrer la
lecture.
La lecture débute et l’écran de lecture s’affiche.
Vous pouvez contrôlez les pistes avec les
touches sur la télécommande.
Boutons activés : 1, 3, 2, 5, 4, 7,
6, RANDOM, REPEAT
Remarque
• Sur les canaux Rhapsody, certaines touches ne
fonctionnent pas.

■ Eléments du menu
Add track to My Library :
Marquez les pistes en cours de lecture.
Add album to My Library :
Marquez les albums en cours de lecture.
Add playlist to My Library :
Marquez les listes de lecture en cours de lecture.
Add channel to My Channels :
Marquez les canaux de radio Rhapsody en cours
de lecture.
Add to My Favorites :
Permet d’ajouter une piste, un canal ou une liste
de lecture à la liste My Favorites.
Conseil
• Vous pouvez supprimer des pistes, des albums et des
canaux Rhapsody marqués de My Library.

Fr-3

Utilisation d’une webradio

Utilisation de SiriusXM Internet Radio
(Amérique du Nord uniquement)

Votre ampli-tuner AV Onkyo comprend un essai
gratuit de SiriusXM Internet Radio. L’écran « Account
Info » affiche le nombre de jours restants dans votre
essai. Une fois la période d’essai expirée, si vous
souhaitez continuer à écouter le service, vous devez
vous abonner. Pour vous inscrire, accédez à
l’adresse
www.siriusxm.com/internetradio à l’aide de votre
ordinateur.

Utilisez q/w pour sélectionner « Sign In », puis
appuyez sur ENTER.
Si vous possédez déjà un compte SIRIUS, vous
pouvez y accéder en sélectionnant « Sign In ».
Saisissez votre nom utilisateur et votre mot de
passe dans l’écran clavier suivant ou dans
Configuration Web. Si vous ne connaissez pas
votre nom d’utilisateur ou votre mot de passe,
appelez Sirius XM au (888) 539-7474 pour
obtenir une assistance.
Conseil
• Si vous souhaitez utiliser plusieurs comptes
utilisateur, consultez « Utilisation de plusieurs
comptes » (➔ page 1). L’identification peut être
réalisée à partir de l’écran « Users ».

Lorsque vous vous inscrivez, vous devez fournir un
nom est un mot de passe utilisateur qui doivent être
saisis dans l’ampli-tuner AV.

■ Utilisation de l’écran clavier
1. Utilisez q/w/e/r et ENTER pour saisir votre
nom d’utilisateur et votre mot de passe.
2. Sélectionnez « OK ».
3. Appuyez sur ENTER. L’écran « Confirm
your entries » s’affiche.
4. Appuyez sur ENTER.
« Please wait... » s’affiche, puis l’écran
« SiriusXM Internet Radio » affiche la catégorie
que vous pouvez sélectionner.

Pour utiliser SiriusXM Internet Radio, l’ampli-tuner AV
doit être connecté à Internet. Suivez les étapes cidessous à l’aide de la télécommande :

Utilisez q/w pour sélectionner la catégorie,
puis appuyez sur ENTER.
L’écran de la liste des canaux de la catégorie
sélectionnée s’affiche.

Fr-4

Utilisez q/w pour sélectionner le canal de
votre choix, puis appuyez sur ENTER.
L’écran de lecture du canal sélectionné s’affiche
et vous pouvez écouter SiriusXM Internet Radio.
Vous pouvez contrôlez les pistes avec les
touches sur la télécommande.
Boutons activés : 2, 3, 7, 6
■ Eléments du menu
Add to My Favorites :
Permet d’ajouter un canal à la liste My Favorites.

Les abonnements SiriusXM Internet Radio sont
vendus séparément et sont subordonnés par les
conditions Sirius (voir www.sirius.com). Assurez-vous
de lire cet accord avant d’acquérir votre abonnement.
Sirius, XM et tous les logos et marques afférents sont
des marques déposées de Sirius XM Radio Inc. et de
ses filiales. Tous droits réservés.

Utilisation d’une webradio

Utilisation de la webradio Last.fm

Last.fm un service de musique qui apprend ce que
vous aimez…
Votre nouvel ampli-tuner AV Onkyo est très intelligent.
Si vous avez un compte Last.fm gratuit, il garde une
trace de toutes les chansons que vous avez juste
jouées. Quand vous vous rendez sur le site Web de
Last.fm, vous pouvez voir les graphiques personnels
de la musique que vous avez appréciée, les partagez
avec vos amis et également voir ce qu’ils aiment.

■ Utilisation de l’écran clavier
1. Utilisez q/w/e/r et le bouton ENTER pour
saisir votre nom d’utilisateur et votre mot de
passe.
2. Sélectionnez « OK ».
3. Appuyez sur ENTER. L’écran « Confirm
your entries » s’affiche.
4. Appuyez sur ENTER.
« Please wait... » apparait puis l’écran « Last.fm
Internet Radio » apparait.

Avec des milliers de biographies, de revues et un
choix infini de stations de radio personnalisées et
sans pub, Last.fm est excellent moyen de découvrir
de la musique. Créez aujourd’hui votre compte
Last.fm gratuit sur www.last.fm/join
Inscrivez-vous et vous pourrez apprécier le meilleur
de la radio sans pub Last.fm sur votre ampli-tuner AV
Onkyo sans ordinateur !
Recommended Radio :
Découvrez les recommandations personnalisées
futées qui changent en même temps que vos goûts.
Artist Radio :
Sélectionnez n’importe quel artiste et nous vous
jouerons une station entière de musique inspirée par
votre choix.
My Library :
Reposez-vous de retour et appréciez les sélections à
partir de toute la musique que vous avez entendue
depuis que vous avez joint Last.fm.
Tag Radio :
Funk polonaise ? Death pop ? Pensez à un style et
nous vous divertirons avec pendant des heures.
Commencez votre essai gratuit immédiatement à la
création votre compte et découvrez par vous-même
ce que cela fait d’avoir la musique du monde au bouts
des doigts. Les derniers prix et les informations
complètes sont disponibles sur www.last.fm/subscribe

Profile :
Vous pouvez lire des pistes de « Recently
Listened Tracks », « Library » et
« Neighbours ».
Account Info :
Vérifiez les informations de votre compte.
Sign Out :
Pour vous déconnecter de votre compte.

Utilisez q/w pour sélectionner « Sign in to
your account », puis appuyez sur ENTER.
Vous possédez déjà un compte Last.fm, vous
pouvez vous y connecter pour sélectionner
« Sign in to your account ». Saisissez votre
nom utilisateur et votre mot de passe dans
l’écran clavier suivant.

■ Eléments du menu
I Love this track :
L’information de la piste est sauvegardée dans le
serveur Last.fm, et la fréquence de lecture
augmente.
Ban this track :
L’information de la piste est sauvegardée dans le
serveur Last.fm, et la fréquence de lecture
diminue.
Add to My Favorites :
Permet d’ajouter une station à la liste My
Favorites.

Utilisez q/w pour sélectionner un menu puis
appuyez sur ENTER.
Search Station :
Vous pouvez rechercher une station par artiste,
par tag ou par nom d’utilisateur.
Top Artists Station :
Vous pouvez lire des pistes des artistes les mieux
évalués.
Top Tags Station :
Vous pouvez lire des pistes des tags les mieux
évalués.
Personal Station :
Vous pouvez lire des pistes de votre station
personnalisée (« Your Library », « Your
Neighbourhood » et « Your
Recommendations »).

Fr-5

Utilisez q/w pour sélectionner une station, puis
appuyez sur ENTER ou 1 pour démarrer la
lecture.
La lecture débute et l’écran de lecture s’affiche.

■ Utilisation du contrôle Scrobbling
Utilisez q/w pour sélectionner « Enable », puis
appuyez sur ENTER.
*

Les services de webradio fournis par un tiers peuvent être
résiliés avec ou sans préavis.
Les services de webradio peuvent ne pas être accessibles
dans certaines zones.

Utilisation d’une webradio

Utilisation de Slacker Personal Radio

Si vous ne possédez pas de compte, créez-en
un à partir du site Web de Slacker
(www.slacker.com) à l’aide de votre
ordinateur.
Si vous possédez déjà un compte Slacker,
sélectionnez « Sign in to your account », puis
appuyez sur ENTER.
L’écran clavier s’affiche. Pouvez saisir des
informations à partir de la télécommande ou des
touches sur l’appareil principal.

Si les informations que vous avez saisies ne
comportent pas d’erreur, utilisezq/w/e/r
pour sélectionner « OK », puis appuyez sur
ENTER.
L’écran de confirmation des informations du
compte s’affiche.

Si vous ne possédez pas de compte,
sélectionnez « Access without Sign In », puis
appuyez sur ENTER pour utiliser une version
restreinte du service.
Veuillez noter que l’utilisation est restreinte.
Conseil
• Si vous souhaitez utiliser plusieurs comptes
utilisateur, consultez « Utilisation de plusieurs
comptes » (➔ page 1). L’identification peut être
réalisée à partir de l’écran « Users ».

Utilisez q/w pour sélectionner un élément du
menu, puis appuyez sur ENTER.
Pour vous déconnecter, utilisez q/w pour
sélectionner « Sign out » depuis cet écran, puis
appuyez sur ENTER.

Utilisez q/w pour sélectionner une station,
puis appuyez sur ENTER ou 1 pour démarrer
la lecture depuis cette station.
L’écran de lecture apparaît.

Vous pouvez contrôlez les pistes avec les
touches sur la télécommande.
Boutons activés : 1, 3, 2, 6
■ Eléments du menu
Rate Song as Favorite :
Permet de stocker des informations sur le
serveur, et d’augmenter la probabilité que le
morceau soit lu de nouveau.
Ban Song :
Permet de stocker des informations sur le
serveur, et de diminuer la probabilité que le
morceau soit lu de nouveau.
Ban Artist :
Permet de stocker des informations sur le
serveur, et de diminuer la probabilité que les
morceaux de cet artiste soient lus de nouveau.
Mark Favorite :
Permet d’ajouter la station en cours de lecture à
vos favoris.
Unmark Favorite :
Permet de supprimer la station en cours de
lecture de vos favoris.
Add song to Library :
Permet d’ajouter la piste en cours de lecture à
votre bibliothèque.
Delete song from Library :
Permet de supprimer la piste en cours de lecture
de votre bibliothèque.
Add to My Favorites :
Permet d’ajouter une station ou un morceau à la
liste My Favorites.

Fr-6

Uso de Internet Radio

Uso de Internet Radio
Procedimientos comunes en el menú
Internet Radio
Nota
• Los servicios disponibles pueden variar de una región a
otra.
• Es posible que determinados servicios de red o contenidos
disponibles a través de este dispositivo no sean accesibles
si el proveedor del servicio da por finalizado el servicio.

Pulse NET.
Aparecerá una lista de los servicios de red y se
iluminará el indicador NET. Si parpadea,
verifique que el cable Ethernet esté firmemente
conectado al receptor de AV.
Seleccione el servicio deseado y pulse
ENTER.
Aparecerá la página principal del servicio
seleccionado.

Uso de múltiples cuentas
El receptor de AV permite múltiples cuentas de
usuario, lo que quiere decir que se puede cambiar
libremente entre varios usuarios. Después de
registrar las cuentas de usuario, el acceso se realiza
desde la pantalla “Users”.

Pulse MENU cuando aparezca la pantalla de
usuarios.
Aparecerán los siguientes elementos del menú:
Add new user:
Remove this user:
Puede guardar una nueva cuenta de usuario o
borrar una existente.

Pandora® Internet Radio
–Primeros pasos (solo EE.UU.)............... 2

Uso de Rhapsody (sólo EE.UU.)................... 3

Uso de SiriusXM Internet Radio
(solo Norteamérica).................................. 4

Uso de Last.fm Internet Radio ...................... 5

Consejo
• Algunos de los servicios no permiten el uso de múltiples
cuentas de usuario.
• Puede guardar hasta 10 cuentas de usuario.
• Para cambiar entre cuentas debe antes cerrar sesión en la
cuenta actual y acceder de nuevo en la pantalla “Users”.

Es-1

Uso de Slacker Personal Radio .................... 6

Uso de Internet Radio

Pandora® Internet Radio
–Primeros pasos (solo EE.UU.)
Pandora es un servicio de radio por Internet gratuito y
personalizado que reproduce la música que usted
conoce y le ayudará a descubrir música que le
encantará.

Utilice q/w para seleccionar “I have a Pandora
Account” o “I’m new to Pandora” y luego
pulse ENTER.
Si no conoce Pandora seleccione “I’m new to
Pandora”. Verá un código de activación en la
pantalla del televisor. Tome nota de este código.
Vaya a un ordenador conectado a Internet y dirija
el navegador a www.pandora.com/onkyo
Introduzca su código de activación y siga las
instrucciones para crear su cuenta de Pandora y
sus emisoras de radio por Internet
personalizadas de Pandora. Puede crear sus
propias emisoras introduciendo sus temas y
artistas favoritos cuando aparezca la solicitud
correspondiente. Una vez creada su cuenta y sus
emisoras, puede regresar al receptor Onkyo y
pulsar Enter para empezar a escuchar su radio
por Internet personalizada de Pandora.
Si ya dispone de una cuenta de Pandora, puede
añadirla al receptor Onkyo seleccionando “I have
a Pandora Account” e iniciando la sesión con su
dirección de correo electrónico y contraseña.

Utilice q/w para seleccionar la emisora en la
lista de emisoras y luego pulse ENTER.
Se inicia la reproducción y aparece la pantalla de
reproducción.
Create a New Station:
Introduzca el nombre de un tema, artista o
género; Pandora creará una emisora de radio
exclusiva para usted basada en las cualidades
musicales de ese tema, de ese artista o de ese
género.
■ Elementos del menú
I like this track:
Si aprueba (pulgar arriba) un tema, Pandora
reproducirá más música parecida.
I don’t like this track:
Si no aprueba (pulgar abajo) el tema, Pandora
eliminará dicho tema de la emisora actual.
Why is this track playing?:
Descubra algunos de los atributos musicales que
Pandora utiliza para crear sus emisoras de radio
personalizadas.
I’m tired of this track:
Si se cansa de un tema, puede “silenciarlo” de
modo que Pandora no lo reproduzca durante un
mes.
Create station from this artist:
Crea una emisora de radio a partir de este
artista.

Consejo
• Si desea utilizar múltiples cuentas de usuario,
consulte “Uso de múltiples cuentas” (➔ página 1). Se
puede iniciar sesión desde la pantalla “Users”.

Es-2

Delete this station:
Esto eliminará de forma permanente una
emisora de su cuenta de Pandora. Toda la
información sobre sus aprobaciones/
desaprobaciones se perderá si quiere volver a
crear la emisora con el mismo tema o artista.
Create station from this track:
Crea una emisora de radio a partir de este tema.
Rename this station:
Le permite renombrar la emisora de radio actual.
Bookmark this artist:
Pandora marcará su artista favorito para su perfil
en www.pandora.com.
Bookmark this track:
Pandora marcará el tema actual y le permitirá
comprarlos todos en Amazon o iTunes ¡con un
solo paso!
Add to My Favorites:
Añade una emisora a la lista Mis favoritos.

PANDORA, el logotipo de PANDORA logo, y la
imagen corporativa de Pandora son marcas
comerciales o marcas comerciales registradas de
Pandora Media, Inc. Uso con permiso.

Uso de Internet Radio

Uso de Rhapsody (sólo EE.UU.)

Utilice q/w para seleccionar “Sign in to your
account” y luego pulse ENTER.
Para utilizar Rhapsody, necesitará una cuenta. Si
todavía no tiene una, puede crear una nueva en
www.rhapsody.com/onkyo
Si ya tiene una cuenta Rhapsody, seleccione
“Sign in to your account” y pulse ENTER.
Escriba su nombre de usuario (normalmente el
correo electrónico) y contraseña en la pantalla de
teclado que aparece a continuación o en la
configuración web.
■ Utilización de la pantalla de teclado
1. Utilice q/w/e/r y ENTER para introducir su
nombre de usuario y su contraseña.
2. Seleccione “OK”.
3. Pulse ENTER. Aparecerá la pantalla
“Confirm your entries”.
4. Pulse ENTER.
Consejo

Utilice q/w para seleccionar el menú y luego
pulse ENTER.
Search:
Puede buscar música por artista, álbum o
canción.
Music Guide:
Puede reproducir canciones por géneros, artistas
principales, álbumes principales o canciones
principales, novedades, selección del sitio.
Rhapsody Channels:
Escuche las emisoras de radio programadas por
los principales redactores de Rhapsody.
Playlists:
Reproduzca sus listas personales.
My Library:
Marque sus álbumes y canciones preferidas en
el catálogo de Rhapsody, usando Mi biblioteca.
Account Info:
Confirme los datos de su cuenta.
Sign Out:
Salga de su cuenta Rhapsody.

• Si desea utilizar múltiples cuentas de usuario,
consulte “Uso de múltiples cuentas” (➔ página 1). Se
puede iniciar sesión desde la pantalla “Users”.

Utilice q/w para seleccionar una emisora y
luego pulse ENTER o 1 para iniciar la
reproducción.
Se inicia la reproducción y aparece la pantalla de
reproducción.
Puede controlar las pistas con los botones del
mando a distancia.
Botones activados: 1, 3, 2, 5, 4, 7,
6, RANDOM, REPEAT
Nota
• En Rhapsody Channels, algunos de los botones no
funcionan.

■ Elementos del menú
Add track to My Library:
Marca las canciones que se están reproduciendo
actualmente.
Add album to My Library:
Marca los álbumes que se están reproduciendo
actualmente.
Add playlist to My Library:
Marca las listas de reproducción que se están
reproduciendo actualmente.
Add channel to My Channels:
Marca las emisoras de Rhapsody que se están
reproduciendo actualmente.
Add to My Favorites:
Añade una canción, emisora o lista de
reproducción a la lista Mis favoritos.
Consejo
• Puede eliminar las canciones, los álbumes y las
emisoras de Rhapsody marcados de Mi biblioteca.

Es-3

Uso de Internet Radio

Uso de SiriusXM Internet Radio (solo
Norteamérica)

Su receptor de AV Onkyo incluye una prueba gratuita
de SiriusXM Internet Radio. La pantalla “Account
Info” muestra los días que quedan de la prueba. Una
vez que termine el periodo de prueba, si desea seguir
escuchando este servicio, deberá contratarlo. para
suscribirse vaya a
www.siriusxm.com/internetradio con su
ordenador.

Utilice q/w para seleccionar “Sign In”, y luego
pulse ENTER.
Si ya tiene una cuenta SIRIUS, puede acceder
seleccionando “Sign In”. Escriba su nombre de
usuario y contraseña en la pantalla de teclado
que aparece a continuación o en la configuración
web. Si no sabe su nombre de usuario o la
contraseña, llame a Sirius XM al número (888)
539-7474 para solicitar asistencia.
Consejo
• Si desea utilizar múltiples cuentas de usuario,
consulte “Uso de múltiples cuentas” (➔ página 1). Se
puede iniciar sesión desde la pantalla “Users”.

Cuando se suscriba, recibirá un nombre de usuario y
una contraseña que deberá introducir en el receptor
de AV.

■ Utilización de la pantalla de teclado
1. Utilice q/w/e/r y ENTER para introducir su
nombre de usuario y su contraseña.
2. Seleccione “OK”.
3. Pulse ENTER. Aparecerá la pantalla
“Confirm your entries”.
4. Pulse ENTER.
Aparecerá “Please wait...” y después la pantalla
“SiriusXM Internet Radio”, que muestra la
categoría disponible para la selección.

Para poder utilizar SiriusXM Internet Radio, el
receptor de AV debe estar conectado a internet. Para
usar el mando a distancia, siga este procedimiento:

Utilice q/w para seleccionar la categoría y
luego pulse ENTER.
Aparece una pantalla con una lista de emisoras
de la categoría seleccionada.

Es-4

Utilice q/w para seleccionar la emisora
deseada y luego pulse ENTER.
Aparecerá la pantalla de reproducción de la
emisora seleccionada y ahora usted podrá
escuchar SiriusXM Internet Radio.
Puede controlar las pistas con los botones del
mando a distancia.
Botones activados: 2, 3, 7, 6
■ Elementos del menú
Add to My Favorites:
Añade una emisora a la lista Mis favoritos.

Las suscripciones a SiriusXM Internet Radio se
venden por separado y se rigen por las condiciones
de Sirius (consulte www.sirius.com). Lea
atentamente este acuerdo antes de comprar la
suscripción. Sirius, XM y todas las marcas y logotipos
relacionados son marcas comerciales de Sirius XM
Radio Inc. y sus filiales. Todos los derechos
reservados.

Uso de Internet Radio

Uso de Last.fm Internet Radio

Last.fm es un servicio musical que sabe lo que le
gusta...
Su nuevo receptor de AV Onkyo es muy inteligente.
Si tiene una cuenta gratuita de Last.fm, hará un
seguimiento de todas las canciones que acaba de
escuchar. Cuando visite el sitio web de Last.fm,
podrá ver listas personales de la música que ha
disfrutado, compartirlas con sus amigos y también
ver lo que les gusta a ellos.

Con sus miles de biografías, críticas y una infinita
variedad de emisoras de radio personalizadas y sin
publicidad, Last.fm es una forma excelente de
descubrir música. Cree hoy mismo una cuenta
gratuita de Last.fm en www.last.fm/join
Si se suscribe podrá disfrutar de lo mejor de Last.fm
Radio sin anuncios en su receptor de AV Onkyo sin
necesidad de un ordenador.
Recommended Radio:
Descubra nuestras interesantes recomendaciones
personalizadas que se adaptan a sus gustos en cada
momento.
Artist Radio:
Escoja cualquier artista y podrá escuchar una
emisora de radio inspirada exclusivamente en su
elección.
My Library:
Relájese y disfrute de selecciones de toda la música
que ha escuchado desde que se registró en Last.fm.
Tag Radio:
¿Polish funk? ¿Death pop? Piense en un estilo y
podrá escucharlo durante horas.

Profile:
Puede reproducir pistas de “Recently Listened
Tracks”, “Library” y “Neighbours”.
Account Info:
Confirme los datos de su cuenta.
Sign Out:
Se desconecta de su cuenta.

Utilice q/w para seleccionar “Sign in to your
account”, y luego pulse ENTER.
Si ya tiene una cuenta de Last.fm, puede
acceder a ella para seleccionar “Sign in to your
account”. Introduzca su nombre de usuario y
contraseña en la siguiente pantalla de teclado.

■ Elementos del menú
I Love this track:
Se guarda la información sobre la canción en el
servidor de Last.fm y aumenta la frecuencia con
la que se reproduce.
Ban this track:
Se guarda la información sobre la canción en el
servidor de Last.fm y se reduce la frecuencia con
la que se reproduce.
Add to My Favorites:
Añade una emisora a la lista Mis favoritos.

Consejo
• Si desea utilizar múltiples cuentas de usuario,
consulte “Uso de múltiples cuentas” (➔ página 1). Se
puede iniciar sesión desde la pantalla “Users”.

Utilice q/w para seleccionar un menú y luego
pulse ENTER.
Search Station:
Puede buscar emisoras por artista, etiquetas o
nombre de usuario.
Top Artists Station:
Puede reproducir canciones de los artistas mejor
clasificados.
Top Tags Station:
Puede reproducir canciones con las etiquetas
mejor clasificadas.
Personal Station:
Puede reproducir pistas de una emisora
personalizada (“Your Library”, “Your
Neighbourhood” y “Your Recommendations”).

Pruébelo gratis ahora mismo. Cree una cuenta y verá
por sí mismo lo que significa tener toda la música del
mundo al alcance de sus oídos. Puede consultar los
precios actualizados y toda la información que desee
en www.last.fm/subscribe

Es-5

Utilice q/w para seleccionar una emisora y
luego pulse ENTER o 1 para iniciar la
reproducción.
Se inicia la reproducción y aparece la pantalla de
reproducción.

■ Uso del control de scrobbling
Utilice q/w para seleccionar “Enable”, y luego pulse
ENTER.
*

Los servicios de radio por Internet suministrados por
terceros pueden cancelarse con o sin aviso previo.
Es posible que los servicios de radio por Internet no estén
disponibles en algunas zonas.

Uso de Internet Radio

Uso de Slacker Personal Radio

Si no tiene una cuenta, cree una en el sitio web
de Slacker (www.slacker.com) con su
ordenador.
Si ya tiene una cuenta de Slacker, seleccione
“Sign in to your account” y pulse ENTER.
Aparecerá la pantalla de teclado. Puede
introducir información desde el mando a
distancia o desde el teclado de la unidad
principal.

Si no hay errores en la información que ha
introducido, utilice q/w/e/r para seleccionar
“OK” y luego pulse ENTER.
Aparecerá una pantalla de confirmación de la
información de la cuenta.

Si no tiene una cuenta, seleccione “Access
without Sign In” y pulse ENTER para utilizar
una versión restringida del servicio.
Tenga en cuenta que el uso estará restringido.
Consejo
• Si desea utilizar múltiples cuentas de usuario,
consulte “Uso de múltiples cuentas” (➔ página 1). Se
puede iniciar sesión desde la pantalla “Users”.

Utilice q/w para seleccionar un menú y luego
pulse ENTER.
Para salir, utilice q/w para seleccionar “Sign out”
en esta pantalla y luego pulse ENTER.

Utilice q/w para seleccionar una emisora y
luego pulse ENTER o 1 para iniciar la
reproducción de la emisora.
Aparecerá la pantalla de reproducción.

Puede controlar las pistas con los botones del
mando a distancia.
Botones activados: 1, 3, 2, 6
■ Elementos del menú
Rate Song as Favorite:
Guarda información en el servidor, haciendo que
sea más probable que la canción se vuelva a
reproducir.
Ban Song:
Guarda información en el servidor, haciendo que
sea menos probable que la canción se vuelva a
reproducir.
Ban Artist:
Guarda información en el servidor, haciendo que
sea menos probable que las canciones de este
artista se vuelvan a reproducir.
Mark Favorite:
Añade la emisora que se está reproduciendo
actualmente a los favoritos.
Unmark Favorite:
Elimina la emisora que se está reproduciendo
actualmente de los favoritos.
Add song to Library:
Añade la canción que se está reproduciendo
actualmente a su biblioteca.
Delete song from Library:
Elimina la canción que se está reproduciendo
actualmente de la biblioteca.
Add to My Favorites:
Añade una emisora o canción a la lista Mis
favoritos.

Es-6

Y1212-1

SN 29401478IRUS

* 2 9 4 0 1 4 7 8 I R U S *

Using Internet Radio

Press MENU while the Users screen is
displayed.
The following menu items appear:
Add new user:
Remove this user:
You can either store a new user account, or
delete an existing one.

En-1

Using Last.fm Internet Radio ........................ 2

Using Internet Radio

Using Last.fm Internet Radio

With thousands of biographies, reviews and an
endless choice of personalised, ad-free radio
stations, Last.fm is a great way to discover music.
Pick up your free Last.fm account today at
www.last.fm/join
UK and Germany only:
Get a subscription and you can enjoy the best of adfree Last.fm Radio on your Onkyo AV receiver without
a computer!
Recommended Radio:
Discover smart personalised recommendations that
adapt as your tastes change.
Artist Radio:
Pick any artist and we’ll play you a whole station of
music inspired by your choice.
My Library:
Sit back and enjoy selections from all the music
you’ve heard since you joined Last.fm.
Tag Radio:
Polish funk? Death pop? Think of a style and we’ll
entertain you with it for hours.

Profile:
You can play tracks from “Recently Listened
Tracks”, “Library” and “Neighbours”.
Account Info:
Confirm your account information.
Sign Out:
It signs out from your account.

Tip
• If you want to use multiple user accounts, see “Using
Multiple Accounts” (➔ page 1). Login can be made
from the “Users” screen.

Use q/w to select menu and then press
ENTER.
Search Station:
You can search station by Artist, Tag, or User
Name.
Top Artists Station:
You can play tracks of top-rated artists.
Top Tags Station:
You can play tracks of top-rated tags.
Personal Station:
You can play tracks from personalized station
(“Your Library”, “Your Neighbourhood” and
“Your Recommendations”).

Start your free trial straight away when you create
your account and see for yourself what it’s like to
have the world’s music at your fingertips. Latest
prices and full information are available at
www.last.fm/subscribe

En-2

Use q/w to select a station, and press ENTER
or 1 to start playback.
Playback starts and the playback screen
appears.
Enabled buttons: 1, 2, 6

■ Using scrobbling control
Use q/w to select “Enable”, and then press ENTER.
*

Internet radio services provided by a third party may be
terminated with or without notice.
Internet radio services may not be available in some areas.

Internetradio verwenden

Internetradio verwenden
Allgemeine Verfahren bei den
Internetradio-Menüs

Verwendung mehrerer Konten
Der AV-Receiver unterstützt mehrere Nutzerkonten,
was bedeutet, dass Sie frei zwischen mehreren
Logins umschalten können. Nach der Anmeldung der
Nutzerkonten wird das Login vom „Users“ Bildschirm
aus vorgenommen.

Anmerkung
• Die verfügbaren Dienste sind länderabhängig verschieden.
• Bestimmte Netzwerkdienste oder über dieses Gerät zur
Verfügung stehende Inhalte stehen eventuell nicht zur
Verfügung, falls der Service-Anbieter seine Dienstleistung
beendet.

Drücken Sie NET.
Es erscheint eine Liste der Netzwerkdienste und
die NET-Anzeige leuchtet. Wenn sie blinkt,
überprüfen Sie ob das Ethernet-Kabel fest im AVReceiver eingesteckt ist.
Wählen Sie den gewünschten Service aus und
drücken Sie ENTER.
Die oberste Seite des ausgewählten Services
erscheint.

Drücken Sie MENU während der Bildschirm
des Nutzers angezeigt wird.
Das folgende Menü erscheint:
Add new user:
Remove this user:
Sie können entweder ein neues Nutzerkonto
abspeichern oder ein bestehendes löschen.

Tipp
• Einige dieser Dienstleistungen lassen keine mehrfachen
Nutzerkonten zu.
• Sie können bis zu 10 Nutzerkonten speichern.
• Um zwischen den Konten umzuschalten, müssen Sie sich
zuerst aus Ihrem aktuellen Konto ausloggen und sich dann
wieder auf dem „Users“ Bildschirm einloggen.

De-1

Verwendung von Last.fm Internet Radio ..... 2

Internetradio verwenden

Verwendung von Last.fm Internet Radio
Last.fm ist ein Musikdienst, der sich Ihre
Lieblingsmusik merkt...
Ihr neuer Onkyo AV-Receiver ist äußerst clever. Wenn Sie
ein kostenloses Last.fm-Konto eingerichtet haben, werden
darin alle kürzlich abgespielten Titel gespeichert. Wenn Sie
die Last.fm-Website besuchen, können Sie Ihre
persönlichen Charts der von Ihnen abgespielten Musik
anzeigen; teilen Sie diese mit Freunden und sehen Sie
auch, welche Musik Ihre Freunde mögen.

können. Die aktuellen Nutzungspreise und umfassende
Infos sind unter www.last.fm/subscribe erhältlich

Nur für Großbritannien und Deutschland:
Holen Sie sich ein Abonnement und Sie können auch
ohne Computer die besten werbefreien Last.fmRadiosender auf Ihrem Onkyo AV-Receiver hören!
Recommended Radio:
Entdecken Sie smarte, persönlich angepasste
Empfehlungen, die sich mit Ihrem Musikgeschmack
verändern.
Artist Radio:
Wählen Sie einen beliebigen Interpreten und wir
spielen für Sie einen ganzen Radiosender mit durch
Ihre Wahl inspirierter Musik.
My Library:
Lehnen Sie sich zurück und erfreuen Sie sich an
einer Auswahl aller Musik, die Sie seit Ihrer
Mitgliedschaft bei Last.fm gehört haben.
Tag Radio:
Polish Funk? Death Pop? Denken Sie an einen
Musikstil und wir unterhalten Sie stundenlang damit.
Starten Sie Ihr kostenloses Probeabo direkt wenn Sie
Ihr Konto erstellen und finden Sie selbst heraus wie es
ist, jederzeit die Musik der ganzen Welt abrufen zu

Verwenden Sie q/w, um „Sign in to your
account“ auszuwählen und dann drücken Sie
ENTER.
Wenn Sie über einen bestehenden Last.fm Konto
verfügen, können Sie sich anmelden und „Sign
in to your account“ wählen. Geben Sie Ihre Ihre
Benutzernamen und das Kennwort in der
folgenden Tastaturanzeige ein.
■ Verwendung der Tastaturanzeige
1. Verwenden Sie q/w/e/r und den ENTER, um
Ihren Nutzernamen und Passwort einzugeben.
2. Wählen Sie „OK“.
3. Drücken Sie ENTER. Die Anzeige „Confirm
your entries“ erscheint.
4. Drücken Sie ENTER.
„Please wait...“ wird angezeigt und danach
erscheint die „Last.fm Internet Radio“-Anzeige.

Mit tausenden von Biografien, Rezensionen und einer
schier endlosen Auswahl an persönlich angepassten,
werbefreien Radiosendern ist Last.fm eine großartige
Gelegenheit, um Musik zu entdecken. Holen Sie sich
Ihr kostenloses Last.fm-Konto noch heute unter
www.last.fm/join

Personal Station:
Sie können Titel aus einem persönlich
angepassten Sender wiedergeben („Your
Library“, „Your Neighbourhood“ und „Your
Recommendations“).
Profile:
Sie können Titel aus „Recently Listened Tracks“,
„Library“ und „Neighbours“ wiedergeben.
Account Info:
Bestätigen Sie Ihre Kontoinformation.
Sign Out:
Zur Abmeldung aus Ihrem Konto.

Tipp
• Falls Sie mehrere Nutzerkonten verwenden möchten,
schlagen Sie bitte unter „Verwendung mehrerer
Konten“ nach (➔ Seite 1). Das Login kann vom
„Users“-Bildschirm aus erfolgen.

Verwenden Sie q/w, um das Menü
auszuwählen und dann drücken Sie ENTER.
Search Station:
Sie können einen Sender anhand Interpreten,
Tags oder Benutzernamen suchen.
Top Artists Station:
Sie können Titel der am besten bewerteten
Interpreten wiedergeben.
Top Tags Station:
Sie können Titel der am besten bewerteten Tags
wiedergeben.

Verwenden Sie q/w, um einen Sender
auszuwählen und dann drücken Sie ENTER
oder 1 , um die Wiedergabe zu starten.
Die Wiedergabe wird gestartet und die
Wiedergabeanzeige erscheint.
Aktivierte Tasten: 1, 2, 6
■ Menüsymbole
I Love this track:
Titel-Informationen werden auf dem Last.fmServer gespeichert und die Häufigkeit der
Wiedergabe wird erhöht.
Ban this track:
Titel-Informationen werden auf dem Last.fmServer gespeichert und die Häufigkeit der
Wiedergabe wird verringert.
Add to My Favorites:
Fügt einen Sender zu meiner My Favorites Liste hinzu.

■ Scrobbling-Steuerung verwenden
Verwenden Sie q/w, um „Enable“ auszuwählen und
dann drücken Sie ENTER.
*

Von Drittparteien zur Verfügung gestellte InternetradioDienste können unter Umständen ohne Vorankündigung
eingestellt werden.
In bestimmten Gebieten sind Internetradio-Dienste
eventuell nicht verfügbar.

Y1212-1

SN 29401479IREU

* 2 9 4 0 1 4 7 9 I R E U *

Remote Control Codes

While holding down the REMOTE MODE button to which you want to assign a
code, press and hold down [DISPLAY] (about 3 seconds).
The REMOTE MODE button/Remote indicator lights.
On Integra products, button names are capitalized. For example, “Remote Mode”
button and “Display” button.
Notes:
• Remote control codes cannot be entered for [RECEIVER] and the multi zone button.
• Only TV remote control codes can be entered for [TV].
• Except for [RECEIVER], [TV], and the multi zone button, remote control codes from any
category can be assigned for the REMOTE MODE buttons. However, these buttons also work
as input selector buttons, so choose a REMOTE MODE button that corresponds with the input
to which you connect your component. For example, if you connect your CD player to the CD
input, choose [TV/CD] when entering its remote control code.

Within 30 seconds, use the number buttons to enter the 5-digit remote control
code.
The REMOTE MODE button/Remote indicator flashes twice.
If the remote control code is not entered successfully, the REMOTE MODE
button/Remote indicator will flash once slowly.
Notes:
• The flashing element of the remote controller will differ according to your AV receiver’s model.
• The remote controller is preconfigured with remote controller presets of different components.
By entering a code from the Remote Control Code list, you can activate the relevant preset for
that component.
• When there are multiple codes related to one manufacturer, try and enter them one-by-one until
it matches your component.
• Depending on the model and year of your component, compatibility is not guaranteed.
• With some models, the remote controller may not not work or its compatibility may be limited
to part of the component’s functionality.
• Besides, it is not possible to add new codes to the existing remote controller presets.
• Though the provided remote control codes are correct at the time of printing, they are subject to
change by the manufacturer.

Remote Control Codes

Codes de télécommande

Códigos de control remoto

Tout en maintenant enfoncé le bouton REMOTE MODE auquel vous souhaitez
associer un code, pressez et maintenez enfoncé le bouton [DISPLAY] (pendant
environ 3 secondes).
Le bouton REMOTE MODE/le témoin Remote s’allume.
Les noms de boutons sont en manjuscules sur les produits Integra. Par exemple, le
bouton « Remote Mode » et le bouton « Display ».
Remarques :
• Les codes de télécommande ne peuvent pas être entrés pour [RECEIVER] et le bouton multi
zone.
• Seul les code de télécommande de téléviseurs peuvent être entrés pour [TV].
• À l’exception de [RECEIVER], [TV] et du bouton multi zone, vous pouvez affecter des codes
de télécommande de n’importe quelle catégorie pour les boutons REMOTE MODE. Cependant,
ces boutons font également office de bouton de sélecteur d’entrée : par conséquent, choisissez
un bouton REMOTE MODE correspondant à l’entrée à laquelle vous souhaitez raccorder votre
appareil. Par exemple, si vous raccordez votre lecteur CD à l’entrée CD, choisissez [TV/CD]
lorsque vous saisissez le code de télécommande.

Manteniendo pulsado el botón REMOTE MODE para el cual desea introducir un
código, pulse y mantenga presionado el botón [DISPLAY] (aproximadamente 3
segundos).
Se iluminará el botón REMOTE MODE/indicador Remote.
En los productos Integra, los nombres de los botones aparecen con mayúsculas. Por
ejemplo, el botón “Remote Mode” y el botón “Display”.
Notas:
• No podrán introducirse códigos de mando a distancia para [RECEIVER] y el botón multizona.
• Únicamente podrán introducirse códigos de mando a distancia de televisor para el botón [TV].
• Con la excepción de [RECEIVER], [TV] y el botón multizona, se pueden asignar códigos de
mando a distancia de cualquier categoría a los botones de REMOTE MODE. No obstante, estos
botones también pueden funcionar como botones de selector de entrada; por tanto, seleccione
un botón REMOTE MODE que se corresponda con la entrada a la cual está conectado el
componente. Por ejemplo, si conecta un reproductor de CD a la entrada de CD, seleccione
[TV/CD] cuando introduzca su código de mando a distancia.

Vous disposez de 30 secondes pour saisir le code de télécommande à cinq chiffres
à l’aide des boutons numérotés.
Le bouton REMOTE MODE/le témoin Remote clignote deux fois.
Si le code de télécommande n’a pas été saisi correctement le bouton REMOTE
MODE/l’indicateur Remote ne clignote qu’une seule fois.
Remarques :

Antes de que transcurran 30 segundos, utilice los botones numéricos para
introducir el código de mando a distancia de 5 dígitos.
El botón REMOTE MODE/indicador Remote parpadeará dos veces.
Si el código de mando a distancia no se introduce correctamente, el botón REMOTE
MODE/indicador Remote parpadeará una vez despacio.
Notas:
• El parpadeo del mando distancia será distinto según el modelo de receptor de AV.
• El mando a distancia está preconfigurado con los ajustes predeterminados de los distintos
componentes. Al introducir un código de la lista de códigos del mando a distancia se puede
activar el ajuste predeterminado de ese componente.
• Cuando hay múltiples códigos relacionados con un fabricante, pruebe a introducirlos uno a uno
hasta que coincida con su componente.
• Dependiendo del modelo y el año de su componente, la compatibilidad no está garantizada.
• Con algunos modelos, es posible que el mando a distancia no funcione o que su compatibilidad
esté limitada a una parte de las funciones del componente.
• Además, no es posible añadir nuevos códigos a los ajustes predeterminados existentes del
mando a distancia.
• Los códigos de mando a distancia suministrados son correctos en el momento de la impresión,
pero el fabricante puede realizar cambios.

• L’élément clignotant de la télécommande différera selon le modèle de votre ampli-tuner AV.
• La télécommande est préconfigurée avec des préréglages de télécommande de différents
appareils. En entrant un code de la liste des codes de télécommandes, vous pouvez activer le
préréglage approprié pour cet appreil.
• Quand il y a de multiples codes liés à un fabricant, essayez-les et entrez-les un par un jusqu’à ce
que cela corresponde à votre appareil.
• Selon le modèle et l’année de votre appareil, la compatibilité n’est pas garantie.
• Avec certains modèles, la télécommande peut ne pas fonctionner ou sa compatibilité peut être
limitée à une partie de la fonctionnalité de l’appareil.
• En outre, il n’est pas possible d’ajouter de nouveaux codes aux préréglages de télécommande
existants.
• Bien que les codes de télécommande fournis soient corrects au moment de l’impression de la
liste, ils sont susceptibles d’être modifiés par le fabricant.

Remote Control Codes

Codici del telecomando

Fernbedienungscodes

Tenendo premuto il tasto REMOTE MODE al quale si desidera assegnare il
codice, premere e tenere premuto [DISPLAY] (per circa 3 secondi).
Il tasto REMOTE MODE/l'indicatore Remote si accende.
Sui prodotti Integra, i nomi dei tasti sono scritti con l'iniziale maiuscola. Ad esempio,
tasto “Remote Mode” e tasto “Display”.
Note:
• I codici di controllo del telecomando non possono essere inseriti per [RECEIVER] e i tasti multi
zona.
• Per [TV] è possibile immettere solo codici telecomando del televisore.
• Tranne che per [RECEIVER], [TV], e per il tasto multi zona, è possibile assegnare codici di
controllo di ogni categoria per i tasti REMOTE MODE. Tuttavia, tali tasti fungono anche da
tasti del selettore d'ingresso, quindi scegliere un tasto REMOTE MODE che corrisponda
all'ingresso al quale viene collegato il dispositivo. Per esempio, se si collega il lettore CD
all'ingresso CD, scegliere il [TV/CD] quando si immette il relativo codice telecomando.

Halten Sie die REMOTE MODE-Taste gedruckt, fur die Sie den Code eingeben
mochten, und drucken Sie (ca. 3 Sekunden lang) die [DISPLAY]-Taste.
Die REMOTE MODE-Taste/Remote-Anzeige leuchtet.
Bei den Integra-Produkten werden die Namen der Tasten groß geschrieben. Zum
Beispiel „Remote Mode“ (Fernbedienungsmodus)-Taste und „Display“-Taste.
Hinweise:
• Der Fernbedienungscode kann nicht [RECEIVER] und der Multi-Zonen-Taste zugeordnet
werden.
• Der Taste [TV] können nur Fernbedienungscodes für einen Fernseher zugeordnet werden.
• Abgesehen von [RECEIVER], [TV] und der Multi-Zone-Taste, können die
Fernbedienungscodes jeder Kategorie den REMOTE MODE-Tasten zugewiesen werden.
Allerdings dienen diese Tasten auch als Quellenwahltasten. Wählen Sie also nach Möglichkeit
eine REMOTE MODE-Taste, die dem Eingang zugeordnet ist, an den Sie die betreffende Quelle
angeschlossen haben. Wenn Sie z.B. einen CD-Player an den CD-Eingang anschließen, sollten
Sie [TV/CD] wenn Sie den Fernbedienungscode eingeben.

Entro 30 secondi utilizzare i tasti numerici per inserire il codice telecomando a 5
cifre.
Il tasto REMOTE MODE/l'indicatore Remote lampeggia due volte.
Se il codice telecomando non viene inserito correttamente, il tasto REMOTE
MODE/l'indicatore Remote lampeggia lentamente una volta.
Note:

• L'elemento lampeggiante del telecomando varia a seconda del modello del ricevitore AV.
• Il telecomando è preconfigurato con preselezioni per diversi apparecchi. Inserendo un codice
dall'elenco dei codici telecomando, è possibile attivare la relativa preselezione per tale
apparecchio.
• Se sono presenti più codici relativi allo stesso produttore, provare a inserirli uno a uno finché
non si arrivi al codice corrispondente dell'apparecchio.
• A seconda del modello e dell'anno dell'apparecchio, la compatibilità non è garantita.
• Con alcuni modelli, il telecomando può non funzionare o la sua compatibilità può essere limitata
a una parte della funzionalità dell'apparecchio.
• Inoltre, non è possibile aggiungere nuovi codici alle preselezioni esistenti del telecomando.
• I codici telecomando specificati sono validi alla data della stampa del presente documento, ma
sono soggetti a variazioni da parte del produttore.

Geben Sie mit den Zifferntasten innerhalb von 30 Sekunden den 5-stelligen
Herstellercode ein.
Die REMOTE MODE-Taste/Remote-Anzeige blinkt zwei Mal.
Wenn der Fernbedienungscode nicht ordnungsgemäß eingegeben wurde, blinkt die
REMOTE MODE-Taste/Remote-Anzeige einmal langsam.
Hinweise:
• Das blinkende Element auf der Fernbedienung unterscheidet sich je nach AV-Receiver-Modell.
• Die Fernbedienung ist mit den Voreinstellungen der Fernbedienung der verschiedenen
Komponenten vorkonfiguriert. Indem ein Code aus der Liste der Fernbedienungscodes
eingegeben wird, können Sie die entsprechende Voreinstellung für die Komponente aktivieren.
• Wenn es mehrere Codes gibt, die sich auf einen Hersteller beziehen, versuchen Sie sie einzeln
einzugeben, bis einer mit Ihrer Komponente übereinstimmt.
• Dies hängt vom Modell und Herstellungsjahr Ihrer Komponente ab und die Kompatibilität ist
nicht garantiert.
• Es kann sein, dass bei einigen Modellen die Fernbedienung nicht funktioniert oder ihre
Kompatibilität sich auf nur auf Teile der Funktionalität der Komponente beschränkt.
• Abgesehen davon ist es nicht möglich, den bestehenden Voreinstellungen der Fernbedienung
neue Codes hinzuzufügen.
• Obwohl die angegebenen Fernbedienungscodes dem Stand bei Drucklegung entsprechen, sind
Änderungen durch den Hersteller vorbehalten.

Remote Control Codes

Afstandsbedieningscodes

Fjärrstyrningskoder

Houd terwijl u de REMOTE MODE toets ingedrukt houdt waarvoor u een code
wilt toewijzen de [DISPLAY] toets ingedrukt (ongeveer 3 seconden).
De toets REMOTE MODE (afstandsbedieningsmodus) / Het indicatielampje
afstandsbediening gaat branden.
Op producten van Integra staan de namen van de toetesn in hoofdletters. Bijvoorbeeld,
de toetsen “Remote Mode” en “Display”.
Opmerkingen:

• Fjärrkontrollkoder kan inte anges för knapparna [RECEIVER] och flerzonsknappen.
• Endast fjärrkontrollkoder för tv kan anges för [TV].
• Förutom [RECEIVER], [TV] och flerzonsknappen, kan fjärrkontrollkoder för vilken som helst
kategori tilldelas för knapparna REMOTE MODE. Dessa knappar fungerar dock även som
ingångväljarknappar, så använd en knapp för REMOTE MODE som motsvarar ingången som
du ansluter utrustningen till. Till exempel, om du ansluter din CD-spelare till CD-ingången ska
du välja [TV/CD] när du anger dess fjärrkontrollkod.

• Er kunnen geen afstandsbedieningscodes worden ingevoerd voor [RECEIVER] en de multi
zone-toets.
• Alleen TV afstandsbedieningscodes kunnen worden ingevoerd voor [TV].
• Behalve voor [RECEIVER], [TV] en de multi zone-toets, kunnen afstandsbedieningscodes
vanuit elke categorie worden toegewezen aan de REMOTE MODE toetsen. Deze toetsen
werken overigens ook als ingangsselectortoetsen, kies dus een REMOTE MODE toets die
overeenkomt met de ingang waarop u uw component wilt aansluiten. Kies indien u bijvoorbeeld
uw CD-speler aansluit op de CD-ingang de [TV/CD] toets bij het invoeren van de
afstandsbedieningscode.

Håll ned knappen för det REMOTE MODE som du vill tilldela en kod samtidigt
som du trycker och håller ned [DISPLAY] (i cirka 3 sekunder).
REMOTE MODE-knapp/Fjärrindikatorlampa.
På Integra-produkter, är knappnamnens begynnelsebokstav en versal. Till exempel,
”Fjärrläge”-knapp och ”Display”-knapp.
Anmärkningar:

Gebruik binnen 30 seconden de cijfertoetsen om de 5-cijferige
afstandsbedieningscode in te voeren.
De toets REMOTE MODE (afstandsbedieningsmodus) / Het indicatielampje
afstandsbediening knippert tweemaal.
Indien de afstandsbedieningscode niet met succes wordt ingevoerd, zal de toets
REMOTE MODE/Remote-indicator eenmaal traag knipperen.
Opmerkingen:

Använd sifferknapparna för att ange den femsiffriga koden inom 30 sekunder.
REMOTE MODE-knapp/Fjärrindikatorlampa blinkar två gånger.
Om fjärrkontrollkoden inte ställdes in, blinkar REMOTE MODEknappen/fjärrindikatorn långsamt en gång.
Anmärkningar:
• Det blinkande elementet på fjärrkontrollen skiljer sig åt beroende på din modell av AV-receiver.
• Fjärrkontrollen har förkonfigurerats med förvalda kanaler på fjärrkontrollen för olika
komponenter. Genom att ange en kod från fjärrkontrollkodlistan, kan du aktivera relevanta
förvalda kanaler för den utrustningen.
• När det finns flera olika koder för en tillverkare ska du försöka att ange dem en och en tills de
stämmer överens med din utrustning.
• Beroende på utrustningens modell och årgång, går det inte att garantera kompatibilitet.
• På vissa modeller kan det hända att fjärrkontrollen inte fungerar eller så kan dess kompatibilitet
vara begränsad till en del av utrustningens funktion.
• Dessutom går det inte att lägga till nya koder till fjärrkontrollens existerande förvalda kanaler.
• Även om erhållna fjärrkontrollkoder är korrekta vid tryckningen, kan de ändras av tillverkaren.

• Het knippergedeelte van de afstandsbediening zal verschillen ten opzichte van het model van
uw AV-receiver.
• De afstandsbediening is voorgeprogrammeerd met voorkeuzetoetsen van verschillende
componenten. Door het invullen van een code uit de afstandsbediening codelijst kunt u de
voorkeuzetoets voor die component activeren.
• Wanneer er meerdere codes gerelateerd zijn aan één fabrikant, probeer deze dan een voor een
totdat de juiste code overeenkomt met uw component.
• Afhankelijk van het model en het bouwjaar van uw component is de compatibiliteit niet
gegarandeerd.
• Bij sommige modellen werkt de afstandsbediening mogelijk niet of is de compatibiliteit ervan
beperkt tot een deel van de functionaliteit van de component.
• Daarnaast is het niet mogelijk om nieuwe codes aan de bestaande voorkeuzetoetsen van de
afstandsbediening toe te voegen.
• Hoewel de gegeven afstandsbedieningscodes correct zijn op het moment van afdrukken, kunnen
deze door de fabrikant gewijzigd worden.

Remote Control Codes

遙控代碼

遥控代码

在按住想指定編碼的 REMOTE MODE （遙控模式）按鈕時，同時按住
[DISPLAY] （顯示）（約 3 秒）。
REMOTE MODE （遙控模式）按鈕 / 遙控指示燈亮起。
在 Integra 系列產品上，按鈕名稱為大寫。 例如，「Remote Mode」（遙控模式）
按鈕和 「Display」（顯示）按鈕。
注意：

• [RECEIVER （接收机）] 和多区域按钮不能输入遥控编码。
• 只能为 [TV （电视）] 输入电视遥控编码。
• 除 [RECEIVER （接收机）]、[TV （电视）] 和多区域按钮外，不能为 REMOTE MODE （遥
控模式）按钮指定任何类别的遥控编码。 但是，这些按钮仍可用作输入选择器按钮，因
此，选择与设备所要连接的输入端对应的 REMOTE MODE（遥控模式） 按钮。 例如，如果
要将 CD 播放机连接到 CD 输入端，应在输入遥控编码时选择 [TV/CD （电视 /CD）]。

• [RECEIER] （接收機）和多區域按鈕不能輸入遙控編碼。
• 您只能為 [TV] （電視）輸入電視遙控編碼。
• 除 [RECEIVER] （接收機）、[TV] （電視）和多區域按鈕外，您可針對 REMOTE MODE
（遙控模式）按鈕指定任何類別的遙控編碼。 但是，這些按鈕仍可用作為輸入選擇器按
鈕，因此，請選擇與您設備所連接輸入接口對應的 REMOTE MODE 按鈕。 例如，如果
要將 CD 播放機連接到 CD 輸入源上，則需在輸入遙控編碼時選擇 [TV/CD]。

按住想指定编码的 REMOTE MODE （遥控模式）按钮的同时，按住 [DISPLAY
（显示）] （大约 3 秒钟）。
REMOTE MODE （遥控模式）按钮 / 遥控指示灯亮起。
Integra 产品上的按钮名称单词首字母大写。例如，“Remote Mode （遥控模
式）”按钮和 “Display （显示）”按钮。
注意：

在 30 秒內，使用數字按鈕輸入 5 位數的遙控編碼。
REMOTE MODE （遙控模式）按鈕 / 遙控指示燈閃爍兩次。
如果無法成功輸入遙控編碼，REMOTE MODE （遙控模式）按鈕 / 遙控指示燈
會慢慢地閃爍一次。
注意：

在 30 秒内，使用数字按钮输入 5 位数的遥控编码。
REMOTE MODE （遥控模式）按钮 / 遥控指示灯闪烁两次。
如果不能顺利输入遥控编码，REMOTE MODE （遥控模式）按钮 / 遥控指示灯会
缓慢闪烁一次。
注意：
• 根据 AV 接收机产品类型的不同，遥控器闪烁元素将会不同。
• 遥控器采用不同设备的遥控器预设进行预配置。通过从遥控器编码列表输入编码，便
可激活相应设备的相关预设。
• 单个制造商关联多个编码时，请尝试逐个输入，直至符合当前设备。
• 根据设备的产品类型和年份的不同，无法保证兼容性。
• 对于某些产品类型，遥控器可能无法工作或其兼容性可能受到部分设备功能性的限制。
• 此外，可能无法将新的编码追加到现有的遥控器预设。
• 尽管付印时所提供的遥控编码是正确的，但制造商会随时更改。

• 視您的 AV 接收機型號而定，遙控器的閃爍元件會有不同。
• 遙控器已預先設定有不同設備的遙控器預設值。 透過輸入遙控編碼清單中的編碼，您
可啟用該設備的相關預設值。
• 當有多個編碼與單一製造商相關時，請嘗試一個接著一個輸入，直到與您的設備對應
為止。
• 視設備的型號和年份而定，並不保證與本公司產品相容。
• 在某些型號上，遙控器可能無法作用，或是其相容性限於部份設備功能。
• 除此之外，您無法新增編碼至現有的遙控器預設值。
• 雖然所提供之遙控編碼在本文件列印時為正確，製造商仍可能會對其作出修改。

Remote Control Codes
Cable Set Top Box

Cable Set Top Box

Cable/PVR Combination

ADB

02254, 02769

Neuf TV

03107

Visiopass

00817

Time Warner

01376, 01877, 02187

Aon

02769

Noos

00817

VTR

01376

UPC

01582

Arris

02187

NTL

01068, 01060

WideOpenWest

01877

Videotron

01877

AT&T

00858

Numericable

02767

Ziggo

VTR

01376

Bright House

01376, 01877

Ono

01068, 01562

00660, 01666, 02015,
02142, 02447, 02774

BT Vision

02294

Optus

01060

Cable & Wireless

01068

Orange

00817

Cable One

01376, 01877

Pace

01376, 01877, 01068,
01060, 01982

Arris

02187

IPTV

Bright House

01376, 01877

ADB

01376, 01877

Panasonic

01488, 01982

Cable One

01376, 01877

Aon

02769

Charter

01376, 01877, 02187

Philips

Cablevision

01376, 01877

AT&T

00858

Cisco

01877, 00858, 01982,
02345, 02378

00817, 01582, 02294,
02767

Charter

01376, 01877, 02187

BT Vision

02294

Pioneer

01877, 01500

Cisco

01877, 01982

Canal+

02657

00817, 00660, 01666,
02015, 02447

RCN

01376

Comcast

00858, 02345, 02378

01877

01376, 01877, 01982,
02187

Cisco

Rogers

Kreatel

01385

01376, 01877, 01982,
02187

Sagem

00817

Cox

01376, 01877

mio TV

02802

01877, 01060, 01666,
02015, 02774

Digeo

02187

Motorola

Freebox

01482

01376, 00858, 01998,
02378

01877, 00858, 01982,
02345

Humax

02142, 03051, 03053

Neuf TV

03107

Insight

01376, 01877

Pace

02657

Cablecom
Cablevision

Com Hem
Comcast

01582

Samsung

WideOpenWest

01877

Ziggo

02142

Cable/PVR Combination
02254, 02769

Cox

01376, 01877

Daeryung

01877

Digeo

02187

DX Antenna

01500

SFR

03107

J:COM

03051, 03053

00817

01376

00858, 02345

France Telecom

Shaw

Scientific Atlanta

Knology

01877

01482

01998, 02802

03107

Freebox

SingTel

SFR

Mediacom

01376, 01877

01998, 02802

01497

01460

SingTel

Fujitsu

Sony

Motorola

01376

00660, 02142, 02447,
03051, 03053

02015

01385

Humax

Stofa

TeliaSonera

Moxi

02187

Suddenlink

01376, 01877

Telus

02345

Numericable

02767

Insight

01376, 01877

Sumitomo

01500

Thomson

02769

Pace

01877

J:COM

03051, 03053

Telewest

01068

Verizon

02378

Panasonic

01982

Knology

01877

TeliaSonera

01385

Philips

01582, 02767

IPTV/PVR Combination

Kreatel

01385

Telus

02345

Pioneer

01877

ADB

Macab

00817

Thomson

01582, 01982, 02769

Rogers

01877

Aon

02769

Mediacom

01376, 01877

Time Warner

01376, 01877, 02187

Samsung

01877

AT&T

00858

mio TV

02802

Toshiba

01509

Scientific Atlanta

01877, 01982

BT Vision

02294

Motorola

01376, 00858, 01562,
01982, 01998, 02378

UPC

01582

Shaw

01376

Cisco

00858, 02345, 02378

Verizon

02378

Moxi

02187

Suddenlink

01376, 01877

Kreatel

01385

Videotron

01877

NEC

01496

Thomson

01582

Motorola

00858, 02378

Virgin Media

01068, 01060

Scientific Atlanta

02769

Remote Control Codes
IPTV/PVR Combination

Neuf TV

03107

Harman/Kardon

70157

Rotel

70157

Onkyo

70868

Philips

02294

Hitachi

70032

SAE

70157

Sony

70490, 70000

Scientific Atlanta

00858

Integra

71817, 70101

Sansui

70157

TEAC

72977

SFR

03107

JVC

70072

SAST

70157

Yamaha

70490

Verizon

02378

Kenwood

70626, 70157, 70036

Siemens

70157

Krell

70157

Silsonic

70036

Cassette Deck

Linn

70157

Simaudio

70157

Aiwa

70157

Arcam

40076
40029

CD/Cassette Dock
TASCAM

73095

CD
Advantage

70032

AH!

70157

Aiwa

70157

Arcam

70157

Atoll Electronique

70157

Audio Research

70157

Audiolab

70157

Audiomeca

70157

Audioton

70157

AVI

70157

Balanced Audio
Technology

70157

Cairn

70157

California Audio Labs 70029, 70303
Cambridge

70157

Cambridge Audio

70157

Carver

70157

CCE

70157

Cyrus

70157

Denon

70626, 70766

DKK

70000

DMX Electronics

70157

Dynaco

70157

Genexxa

70000, 70032

Goldmund

70157

Grundig

70157

Loewe

70157

Sonic Frontiers

40029

Magnavox

70157

Sony

70490, 70000

Audiolab

Marantz

70626, 70029, 70157

Sylvania

70157

Carver

40029
40076

Matsui

70157

TAG McLaren

70157

Denon

MCS

70029

Tandy

70032

Grundig

40029
40029
40070

Memorex

70032

TASCAM

73533, 73095

Harman/Kardon

Meridian

70157

TEAC

73531, 73551, 73532

Inkel

70029, 70303

JVC

40244
40070

Micromega

70157

Technics

Miro

70000

Thorens

70157

Kenwood

Mission

70157

Thule Audio

70157

Magnavox

40029
40029

Myryad

70157

Traxdata

70626

Marantz

NAD

70000, 70721

Universum

70157

Myryad

40029

70072

Onkyo

42157

70000, 70032, 70157

Optimus

40027
40029

Naim
NSM

70157

Victor

70157

Wards

Onkyo

71817

Yamaha

70490, 70032, 70036

Philips

Optimus

70000, 70032

Zonda

70157

Pioneer

40027

Polk Audio

40029

Panasonic

70029, 70303

Philips

70626, 70157

CD-R

Radiola

40029

Pioneer

70032, 70101

Denon

70626, 70766

RCA

40027

Polk Audio

70157

JVC

70072

Revox

40029

70157

Kenwood

70626

Sansui

40029

Proton

70157

Marantz

70626

Sony

40243

QED

70157

Onkyo

71323

Thorens

40029

70157

Philips

70626

Victor

40244

Quasar

70029

Sony

70000

Wards

40027, 40029

Radiola

70157

TASCAM

71830, 72304

Yamaha

40097

RCA

70032

Restek

70157

Primare

Quad

Revox

CD-R/MD
TASCAM

70157

Accessory
73511

Apple

81115

Remote Control Codes
Accessory

Satellite Set Top Box

Jamo

82228

Alba

01284

Centrex

01457

Durabrand

01284

Logitech

82182

Allvision

01334

CGV

01413, 01567

Echostar

Onkyo

82990, 81993, 82351

Amstrad

Chess

01334, 01626

00775, 00853, 01323,
01409, 02527

Polk Audio

82228

00847, 01175, 01662,
01693

CityCom

01176

Eco-Star

01413

Ansonic

02418

Clatronic

01413

Edision

01631

Arnion

01300

Clayton

01626

Elap

01413, 01567
02418

Video - Accessory
ADB

02254, 02769

ASCI

01334

Com Hem

01176, 01915

Elbe

Aon

02769

AssCom

00853

Comag

01413

Energy Sistem

01631, 02418

Apple

02615

Astro

00173, 01100

Comsat

01413

Engel

01251

AT&T

00858

Atlanta

02418

Coship

01457

EuroLine

01251

BT Vision

02294

Atsat

01300

Crown

01284

Europhon

01334

Canal+

02657

AtSky

01334

01631

Europsat

01413, 01611

Cisco

00858, 02345, 02378

Audiola

02418

01409

Expressvu

00775

Kreatel

01385

Aurora

00879, 00642, 01433

Cyfrowy Polsat

00853, 02527

Fagor

01611

mio TV

02802

Austar

00879, 00642, 01259

D-box

00723, 01114

Ferguson

01291

Motorola

01376, 00858, 01998,
02378

Avanit

01631

01626

Finlux

01626

Awa

02418

Denver

02418

Fly Com

01457

Neuf TV

03107

Axil

01413, 01457, 02418

Dgtec

01631, 02418

FMD

01413, 01457

Pace

02657

Axitronic

01626

02418

00879, 01176, 01356

Philips

02294

Balmet

01457

Dick Smith
Electronics

Foxtel
Freesat

02408

Scientific Atlanta

00858, 02345

Bell ExpressVu

00775

Digi Raum Electronics 01176

Fuba

00173, 01251

SFR

03107

Belson

02418

Digiality

01334

Galaxis

00853, 00879

SingTel

01998, 02802

Big Sat

01457

Digihome

01284

General Satellite

01176

TeliaSonera

01385

Black Diamond

01284

DigiLogic

01284

Globo

01251, 01334, 01626

Telus

02345

Blaupunkt

00173

DigiQuest

01300, 01457, 01631

GOI

00775

Thomson

02769

Boshmann

01413, 01631

Digisky

01457

Gold Box

00853

Verizon

02378

Boston

01251

DigitalBox

01100, 01631

Gold Vision

01631

Boxer

01458

Digiwave

01631

GoldMaster

01334

British Sky
Broadcasting

00847, 01175, 01662

DirecTV

01377, 00099

Goodmans

01284, 01291

Dish Network

00775

Gradiente

00099, 00887

BskyB

00847, 01175, 01662

Satellite Set Top Box

Dishpro

00775

Grandin

01626

Bush

01284, 01291, 01626

@sat

01300

DishTV

01300

Grocos

01409, 01457

Canal Digital

00853, 01334

@Sky

01334

DRE

01176

Grundig

Canal Satellite

00853, 02657

01284

01237

00847, 00853, 00173,
00879, 01284, 01291

Acoustic Solutions

Dream Multimedia

Canal+

00853, 02657

02280, 02418

02418

00642, 00887, 01259

DSE

Haier

ADB

CanalSat

00853, 02657

01626

Akura

01626

00879, 00642, 01433

Hallo

Receiver
Onkyo

52503

Cyfra+

Dantax

DSTV

Remote Control Codes
Satellite Set Top Box

Satellite Set Top Box

Hama

01567

Leiko

01626

Pace

Sat Industrie

01611

Hanseatic

01100

Lemon

01334

SAT+

01409

Hirschmann

00173

Lenoxx

01611

Hitachi

01284

Linsar

01284

00847, 00853, 00887,
01175, 01323, 01356,
01423, 01662, 01693,
01850, 02059, 02060,
02211, 02657

Hornet

01300

Listo

01626

Pacific

01284

Schaub Lorenz

02418

HTS

00775

Lodos

01284

Palcom

01409, 01611

Schneider

01206, 01251

Humax

01377, 01176, 01427,
01675, 01808, 01882,
01915, 02144, 02408,
02616

Logik

01284

Panasat

00879, 01433

Schwaiger

01334, 01457, 01631

Macab

00853

Panasonic

00847, 01304, 01404,
03099

Sedea Electronique

01206, 01626

SEG

01251, 01284, 01626

ID Digital

01176

ID Sat

01334

ILLUSION sat

01631

Imperial

01195, 01334

Indovision

00887

Satplus

01100

SatyCon

01631

Manhattan

01300

Maspro

00173

Panda

00173

Servimat

01611

Matsui

00173, 01284, 01626

Pass

01567

ServiSat

01251

Maximum

01334

peeKTon

01457, 02418

Shark

01631

Mediabox

00853

Philips

Sherwood

01409

Mediacom

01206

Siemens

MediaSat

00853

00099, 00853, 00173,
01114, 00887, 00133,
02211

00173, 01334, 01626,
02418

Medion

01334, 01626

Phoenix

02418

Sigmatek

02418

Pino

01334

SKY

Pioneer

00853, 01308

PMB

01611

00099, 00847, 00887,
01175, 01662, 01693,
01850, 02754

00173

Premiere

00723

SKY Brazil

00887

01251

Pro Basic

00853

SKY Deutschland

02754

Movistar

02527, 02761

Proline

01284

SKY Italia

00853, 01693, 01850

Multichoice

00879, 00642, 01433,
02059, 02060

QNS

01404

SKY New Zealand

02211

RCA

01291

SKY PerfecTV!

02299, 02616, 03099

01251

Sky XL

01251

iNETBOX

01237

Inno Hit

01626

Innova

00099

inVion

02418

iotronic

01413

ISkyB

00887

ITT

02418

ITT Nokia

00723

Jadeworld

00642

Jaeger

01334

MySky

01356, 01693, 01850

Regal

JVC

00775

NEOTION

01334

Roadstar

00853

Sky+

01175, 01662

KabelBW

01195, 01882, 01915

Netsat

00099, 00887

Rollmaster

01413

Skymaster

Kaon

01300

Nikko

00723

Rownsonic

01567

01334, 01409, 01567,
01611

Kathrein

00173, 01561, 01567

Nokia

00853, 00723, 01223

SAB

01251, 01300, 01631

Skymax

01413

Nordmende

01611

Sagem

Kenwood

00853

MegaSat

01631

Metronic

01334, 01413, 01631,
02418

Metz
Moserbaer

01114

Koenig

01631

NPG

01631

Saivod

02418

Kreiling

01626

Onn

01284

Samsung

01377, 00853, 01175,
01206, 01458, 01662,
02986

Kreiselmeyer

00173

Optex

01413, 01611, 01626

L&S Electronic

01334

Optus

00879, 01356

Orbis

01334

Orbitech

01100, 01195

LaSAT
Lava

00173
01631

Skyplus

01175, 01334

SkySat

01100

Skyvision

01334

SM Electronic

01409

Smart

01404, 01413, 01631

Sansui

01251

SmartVision

01457

Sanyo

01626

Sony

Sat Control

01300

00847, 00853, 01558,
02299

Remote Control Codes
Satellite Set Top Box

Satellite Set Top Box

SAT/PVR Combination

Star

00887

UBC

00642

Canal+

02657

SKY Deutschland

02754

Stream System

01300

UEC

00879, 01356

CanalSat

02657

SKY Italia

01693, 01850

Strong

00853, 00879, 01284,
01300, 01409, 01626,
02418

United

01251, 01626, 02418

Cyfrowy Polsat

02527

SKY New Zealand

02211

Unitymedia

01882

DigiQuest

01300

SKY PerfecTV!

02299, 03099

Universum

00173, 01251

DirecTV

01377, 00099, 20739

Sky+

01662

Variosat

00173

Dish Network

00775

Skyplus

01175, 01334

VEA

02418

Dishpro

00775

Smart

01631

Vestel

01251, 01284

Dream Multimedia

01237

Sony

02299

Viasat

01195

Echostar

00775, 02527

Stream System

01300

Vision

01626

Edision

01631

Strong

01300

Visiosat

01413, 01457

Expressvu

00775

Sunny

01300

Vitecom

01413

Foxtel

01356

TechniSat

01195

Vivax

02418

Humax

Technosat

01206

Volcasat

02418

01176, 01427, 01675,
01808

Telefonica

02527

Wavelength

01413

ID Sat

01334

Telestar

01195

Wharfedale

01284

iNETBOX

01237

Thomson

01175, 01662

Wisi

00173

Kaon

01300

Topfield

01206

Worldsat

01251

Kathrein

01561

Viasat

01195

Woxter

02418

Maximum

01334

Xtreme

01300

Xsat

00847, 01323

Mediacom

01206

Xtreme

01300

MegaSat

01631

Television

01413

Movistar

02527

A.R. Systems

10556, 10037

Yes

00887

Multichoice

02059, 02060

Accent

10037

Zehnder

01251, 01334, 01413,
01631

MySky

01356, 01693, 01850

Acer

11339

NEOTION

01334

Acoustic Solutions

11037, 11667

02280, 02761

Pace

01175, 01356, 01423,
01662, 01693, 01850,
02059, 02060, 02211,
02657

Action

10650

Sunny

01300

Sunstar

00642

Supernova

00887

Supratech

01413

Systec

01334

Sytech

02418

TBoston

01251, 02418

TEAC

01251

Technical

01626

Technika

01284

TechniSat

01100, 01195

Technosat

01206

Techwood

01251, 01284, 01626

TELE System

01251, 01409, 01611

Telefonica

02527, 02761

Telestar

01100, 01195, 01251,
01334, 01626

Televes

01300, 01334

Televisa

00887

Tevion

01409

Thomson

00847, 00853, 01175,
01046, 01291, 01662

Tonna

01611

Topfield

01206

Toshiba

01284

Trevi
Triax

01251
00853, 01251, 01291,
01413, 01611, 01626,
01631

Yakumo

Zinwell

SAT/PVR Combination
@sat

01300

Amstrad

01175, 01662, 01693

Atsat

01300

Bell ExpressVu

00775
01175, 01662

Tricolor TV

01176

British Sky
Broadcasting

True Visions

02408

BskyB

01611

Canal Satellite

Twinner

Panasonic
Philips
Samsung

01304, 03099
00099
01175, 01206, 01662

Sat Control

01300

Schneider

01206

Addison

10653

AEG

11037, 11324

Agfaphoto

12719

Aiko

10037

Aim

10037, 10499

Akai

10178, 10556, 10037,
10714, 10715, 10208,
11675

01175, 01662

Sedea Electronique

01206

Akiba

10037

02657

SKY

01175, 01662, 01693,
01850, 02754

Akito

10037

Remote Control Codes
Television
Akura

Alba
Alien

Television
10171, 10037, 10714,
10668, 11037, 11363,
11585, 11667, 11709
10037, 10714, 10668,
11037, 11585
11037

Allstar

10037

Amstrad

10171, 10037, 11037

Anam

10037

Television
11037

Classic

10499

DMTech

12001

Beon

10037

Clatronic

10037, 10714, 11324

Domeos

10668

Berthen

10556, 10668

Clayton

11037

Drean

10037

Bestar

10037

Condor

10037

DSE

10698

Bexa

12493

Conrowa

10698

Dual

Black Diamond

11037

Contec

10037

10037, 11037, 11585,
11667

Blaupunkt

10195

Cosmel

10037

Durabrand

Blue Sky

10556, 10037, 10625,
10714, 10668, 11037,
10715, 10499, 11324,
11363, 11652, 11709

CPTEC

10625, 11363

10178, 10171, 10714,
11037, 11652

Crown

10037, 10714, 10668,
11037, 10715, 10208,
11652

Dux

10037

Anam National

10037, 10650

Andersson

11585

Anitech

10037

Boca

11652

Cyberpix

Ansonic

10037, 10668

Boman

11324

D-Vision

AOC

10178, 10625, 11365

Bork

11363

Ardem

10037, 10714

BPL

10037, 10208

Arena

10037

Brandt

Aristona

10556, 10037

ART

11037

Art Mito
Asberg

DX Antenna

11817, 13817

Dynatron

10037

11667

Dynex

12049

10556, 10037

e-motion

11709

Daewoo

10178, 10556, 10037,
10634, 10499, 12098

E:max

11324

Easy Living

11666, 11709

10625, 10714, 10560

Dansai

10037, 10208

ECE

10037

Brimax

11709

Dantax

10556, 10037

10037, 10668

10714, 11037, 10715,
11652

Elbe

Brinkmann

11585

Brionvega

10037

Datsura

10208

10037

Bush

10556, 10037, 10714,
10668, 11037, 10698,
10208, 11585, 11652,
11667, 12719

Dawa

10037

Daytron

10037

Astra

10037

ATD

10698

Atlantic

10037

Audiosonic

10037, 10714, 10715

Audioworld

10698

Aventura

10171

Axxon

10714

Baird

10208

Barco

10556

Basic Line

10556, 10037, 10668,
11037

Baur

10037, 10195, 10512

Beaumark

10178

Beijing

10208

Beko

10037, 10714, 10715,
11652

Belson

Television

Belstar

10698

Byd:sign

12140, 12209

Camper

10037

Carad

10668, 11037

Carena

10037

Carrefour

10037

Cascade

10037

Casio

De Graaf

10208

DEC

11709

Decca

10037

Electrograph

11755

Element

11886

Elfunk

11037

ELG

10037

Elin

10037

Elite

10037

Emerson

10178, 10171, 10037,
10714, 10668, 11394,
11864, 11886

Denver

10037, 11709

Desmet

10037

Diamant

10037

Envision

11365, 11506

Diamond

10698

Epson

11379

10037

Dick Smith
Electronics

10698

Erres

10037

Cathay

10037

ESA

10171

Digatron

10037

CCE

10037

ESC

10037

Digihome

11667

Centrum

11037

Euroman

10037

Digiline

10037, 10668

Centurion

10037

Europa

10037

Digitek

11709

Changhong

10508

Europhon

10037

Digitor

10037, 10698

Chimei

11666

Evesham

11248, 11667

Dixi

10037

Clarivox

10037

Excello

11037

11363

Exquisit

10037

Remote Control Codes
Television
Ferguson

Television
10037, 10625, 10560,
10195, 11037, 11585

Fidelity

10171, 10037, 10512

Finlandia

10208

Finlux

10556, 10037, 10714,
10715, 11248, 11667

Firstline

10556, 10037, 10714,
10668, 11037, 10208,
11363

Fisher

10208

Flint

10037

Formenti

10037

Fraba

10037

Friac

10037, 10499

Fujicom

11709

Fujitsu

10809

Fujitsu Siemens

10809, 11248, 11666

Funai

10171, 10714, 10668,
11037, 11394, 11666,
11817, 13817

G-Hanz

11363

Gaba

11037

Galaxi

10037

Galaxis

10037

Gateway

11755

10178, 11454, 10625,
10560

Goodmans

Gorenje
Gradiente
Graetz

Television
10556, 10037, 10625,
10714, 10560, 10668,
10634, 11037, 10499,
11585, 11667
11585
10037
10714

Granada

10037, 10560, 10208

Grandin

10556, 10037, 10714,
10668, 11037, 10715,
11652

Television

Hoeher

10714

Karcher

10714, 11324

Hornyphon

10037

Kathrein

10556

Hugoson

11666

Kendo

10037, 11037, 11585

Humax

11295

Kennex

11037

Hypson

10556, 10037, 10714,
10668, 11037, 10715

Kioto

10556

Kiton

10037, 10668

11037, 10698

KLL

10037

Iberia

10037

Kneissel

10556, 10037, 10499

ICE

10037

Koenig

10037

iLo

11394

Kolin

10037

10150, 10037, 11610,
11755

Hyundai

Grundig

10556, 10037, 10195,
11223, 11667, 12625

Imperial
Indiana

10037

Kolster

10037

GVA

11363, 12098

Ingelen

10714

Konka

10037, 10714

H&B

12001

Inno Hit

11037, 11585

Korpel

10037

Haier

10037, 10698, 10508

Innova

10037

Kosmos

10037

Hallmark

10178

Insignia

10171, 11423, 12049

Kunlun

10208

Hankook

10178

Integra

11807, 13100, 13500

L&S Electronic

10714

Hanseatic

10556, 10037, 10625,
10714, 10634, 10499,
12001

Interbuy

10037

Lavic

11363

Interfunk

10037, 10512

Lavis

11037

Internal

10556

Lecson

10037

Intervision

10037

Lenco

10037, 11037

Irradio

10037

Leyco

10037

IRT

10698

Isukai

10037

10178, 10556, 10037,
10714, 10715, 10698,
11423, 11768, 11840,
12182, 12358, 12424,
12834

Hantarex

10037

Hantor

10037

Harwood

10037

Hauppauge

10037

11324

HCM

10037

GEC

10037

Highline

10037

Genesis

10037

Hinari

10037, 10208

Genexxa

10037

Hisawa

10714

GFM

10171, 11864, 11886

Hisense

Godrej

11585

10556, 10508, 10208,
11363, 12098

Goldfunk

10668

GoldStar

10178, 10037, 10714,
10715

ITS

10037

ITT

10208

ITT Nokia

10208

Liesenkoetter

10037

ITV

10037

Lifetec

JGC

11709

10037, 10714, 10668,
11037, 12001

Jinfeng

10208

Linsar

11585

10150, 10178, 10037,
10634, 11037, 10508,
10499, 10578, 11576,
11585, 11643, 11667,
11691, 12433

Jinxing

10556, 10037, 10698

Local India TV

10208

JMB

10556, 10634, 10499

Local Malaysia TV

10698

Jubilee

10556

Lodos

11037

JVC

10650, 10653, 10508,
11428, 11601, 12271

Loewe

10037, 10512, 11884

Hitachi Fujian

10150

Logik

11037, 10698

Kaisui

10037

Hitec

10698

Logix

10668

Hitachi

Remote Control Codes
Television

Television

Luma

11037

Metronic

10625

NetTV

11755

Orline

10037

Lumatron

10037, 10668

Metz

10037, 10668, 10195,
11037

Neufunk

10556, 10037, 10714

Ormond

10668, 11037

Lumenio

10037

New Tech

10556, 10037

Osaki

10556, 10037

Lux May

10037

MGA

10150, 10178

Newave

10178

Osio

10037

Luxor

11037, 10208

Micromaxx

Nikkai

10037

Osume

10037

LXI

10178

10037, 10714, 10668,
11037, 11324, 12001

Nikkei

10714

Otto Versand

M Electronic

10037, 10714, 10634,
10195, 10512, 11652

Nikko

10178

10556, 10037, 10195,
10512

Nokia

10208

Pacific

Norcent

11365

10556, 10714, 11037,
11324

Nordmende

10037, 10714, 10560,
10195, 11585, 11667,
12001

Palladium

10556, 10037, 10714

Microspot

11614

Mikomi

11037, 11585
10037

Madison

10037

Minato

Magnavox

10171, 11454, 11365,
11506, 11755, 11867,
12372

Minerva

10195, 11248

Ministry Of Sound

11667

Minoka

10037

Magnum

10037, 10714, 10715

Mirai

11666

Normerel

10037

Manesth

10037

Mitsubishi

10150, 11250, 10178,
10556, 10037, 11037,
10512, 11171

Nortek

10668

Manhattan

10037, 10668, 11037

Marantz

11454, 10556, 10037

Mark

10037, 10714, 10715

Mivar

Master's

10499

Moree

10037

10698

Morgan's

10037

Masuda

10037

Moserbaer

11585

Matsui

10556, 10037, 10714,
10195, 11037, 10208,
11666, 11667

MTC

10512

MTlogic

10714

Mudan

10208

Mastro

10609

Matsushita

10650

Multitec

10037, 10668, 11037

Maxent

11755

Multitech

10037

Maxess

12493

Myrica

11666

Meck

10698

Myryad

10556

NAD

10178, 10037

10556, 10037, 10714,
10668, 11037, 10698,
10512, 11248, 11585,
11667, 12001, 12719

Naiko

10037

Nakimura

10037

National

10508, 10208

Megatron

10178

NEC

MEI

11037

10178, 10653, 10508,
10499

Neckermann

10556, 10037

NEI

10037, 11037

NEO

11324

Mediator
Medion

Memorex

10556, 10037

10150, 10178, 11037

Mercury

10037

Mermaid

10037

Netsat

10037

Novatronic

10037

Novita

11585

Nu-Tec

10698

O.K.Line

11037, 11324

Oceanic

10208

Odys

12719

Okano

10037

OKI

11585, 11667

Olevia

11610, 12124

Omni

10698

Onei

11667

Onida

10653

Palsonic

10037, 10698

Panama

10037

Panasonic

11480, 10037, 10650,
10508, 10208, 11636,
12170

Panavision

10037

Panda

10698, 10508, 10208

Pansonic

11636

Penney

10178

Perdio

10037

Perfekt

10037

Petters

10037

Philco

10178, 10171, 10037,
11394

Philips

10178, 10171, 11454,
10556, 10037, 10512,
10605, 10690, 11394,
11506, 11867, 12372

Onimax

10714

Onix

10698

Phocus

10714, 11652

Onkyo

11807, 13100, 13500

Phoenix

10037

Onn

11667, 11709

Phonola

10556, 10037

Onyx

11709

Pioneer

Opera

10037, 10714

10037, 10698, 10512,
11457, 11636, 12171

Optimus

10650

Plantron

10037

Orbit

10037

Playsonic

10037, 10714, 10715,
11652

Orion

10556, 10037, 10714,
11037, 12001

Powerpoint

10037, 10698

Prinston

11037, 10715

Remote Control Codes
Television

Television

Profitronic

10037

Rowa

10037, 10698

Siera

10556, 10037

Svasa

Proline

10037, 10625, 10634,
11037

Saba

10625, 10714, 10560

Silva

10037

Swisstec

11614, 11775

Sagem

10618

Silva Schneider

10037

Sylvania

10037, 10714, 10668,
11324, 11585, 11667,
11709, 12001

Saivod

10037, 10668, 11037

Silver

10715

10171, 11394, 11864,
11886

Salora

10208, 12001

SilverCrest

11037

Symphonic

10171, 11394

Sinudyne

10037

Synco

10178, 11755

SKY

10037, 11614, 11775

Syntax

11610

10037, 10698

Sysline

10037

Sliding

11324

Tacico

10178

SLX

10668

Talent

10178
10650

Prosonic

Protech

10037, 10668, 11037

Proton

10178

ProVision

10556, 10037, 10714,
11324

Pvision

12001

Pye

10556, 10037

Qingdao

10208

Quasar

10650

Quelle

10037, 10668, 10195,
11037, 10512

R-Line

10037

Radiola

10556, 10037

Radiomarelli

10037

RadioShack

10178, 10037

Radiotone

10037, 10668, 11037

RCA

10178, 11454, 10625,
10560, 10618, 11781,
12247, 12403, 12434,
12746, 12932

Realistic

10178

Recor

10037

Rectiligne

10037

Sampo
Samsung

10178, 10171, 10650,
11755
10178, 10556, 10037,
10618, 10650, 10208,
12051

Skyworth

10208

Sansui

10171, 10037, 10714,
11248, 12001

Solavox

10037

Tashiko

Sanyo

11037, 10508, 10208,
11142, 11365, 11585,
11667, 11974

Soniko

10037

Tatung

10037, 11248, 11324

12493

TCL

Sonitron

10208

10698, 12403, 12434,
13183

10556, 10037

Sonneclair

10037

TCM

10714, 12001

TEAC

10178, 10171, 10037,
10714, 10668, 11037,
10698, 10512, 11248,
11363, 11709, 11755

SBR

Soniq

Schaub Lorenz

10714, 11324, 11363,
11667, 12001

Sonoko

10037

Schneider

10556, 10037, 10714,
10668, 11037

Sonolor

10208

Sontec

10037

Sony

10810, 11505, 11167,
11651, 11825

Tec

10037

Tech Line

10037, 10668

Soundesign

10178

Technica

11037

Soundwave

10037, 11037, 10715

Technics

10556, 10650

Sowa

10178

Technika

11667

Squareview

10171

TechniSat

10556

Standard

10037, 11037, 11709

Technisson

10714, 11652

Starlite

10037

Techno

11585

10037

Technosonic

11610

10556, 10625, 10499,
11324
11709

Schoentech
Scotch
Scott
Sears

11037
10178
10178
10178, 10171

Seaway

10634

Seelver

11037

SEG

10037, 10668, 11037,
12719

10037

SEI

10037

Strato

Reflex

10037, 10668, 11037

Sei-Sinudyne

10037

SunBriteTV

Relisys

11585

Serie Dorada

10178

Sungoo

11248

Techvision

Remotec

10171, 10037

Shanghai

10208

Sunny

10037

Techwood

11037, 11667

Reoc

10714

Sharp

10037

Tecnimagen

10556

Revox

10037

10650, 10818, 11165,
11423, 11659

Sunstar
Sunstech

12001

Teco

10178, 10653

RFT

10037

Shintoshi

10037

Sunwood

10037

Tedelex

10208, 11709

Roadstar

10037, 10714, 10668,
11037, 10715

Shivaki

10178, 10037

Supersonic

10208

Teknika

10150

Siam

10037

SuperTech

10556, 10037

TELE System

11585

Siemens

10037, 10195

Supra

10178

Telecor

10037

Redstar

Rolson

12001, 12098

Remote Control Codes
Television
Telefunken

Telefusion

Television
10037, 10625, 10714,
10560, 10698, 11585,
11667
10037

Television

Ultravox

10037

UMC

11614, 11775

Unic Line

10037

Uniden
United

Wharfedale

PVR
10556, 10037, 11324,
11667

ReplayTV

20616

Sonic Blue

20616

White Westinghouse

10037

TiVo

20739

12122

Wilson

10556

10556, 10037, 10714,
11037, 10715, 11652

Windsor

10668, 11037

TV/VCR Combination

Windy Sam

10556

Telegazi

10037

Telemeister

10037

Amstrad

10171

Telesonic

10037

Unitek

11709

Wintel

10714

Ferguson

10625

Telestar

10556, 10037

Universal

10037, 10714

World-of-Vision

12001

Fidelity

10171

Teletech

10037, 10668, 11037

Universum

Wyse

11365

GoldStar

10037

Teleview

10037

10037, 10668, 10195,
11037, 10618, 10512

Xenius

10634

Grundig

10556, 10037, 10195

Tennessee

10037

Univox

10037

Xiahua

10698

10178

Tensai

10037, 11037, 10715

V7 Videoseven

11666, 11755

XLogic

10698

Mitsubishi

10556

Tesla

10556, 10037, 10714,
11037, 11652

Vestel

10037, 10668, 11037,
11585, 11667

Xrypton

10037

Philips

10556, 10037

Tevion

10556, 10037, 10714,
10668, 11037, 11248,
11585, 11667

Vexa

10037

Yamaha

10650, 11576

Radiola

10556

Yamishi

10037

Saba

10625

Yokan

10037

Sanyo

11974

Yoko

10037

Schneider

10556, 10037

YU-MA-TU

10037

Sharp

10818

Zenith

10178, 10037, 11365,
11423, 12358

Siemens

10037

Sony

11505
10178, 10171

Thomson

10037, 10625, 10560

Thorn

10037, 10499, 10512

Thorn-Ferguson

10499

TMK

10178

Tokai

10037, 10668, 11037

Tokaido

11037

Topline

10668, 11037

Toshiba

10195, 11037, 10618,
10650, 10508, 11169,
11508, 11524, 11652,
12203

Victor

10650, 10653, 11428

Videocon

10037, 10508

VideoSystem

10037

Vidtech

10178

Viewsonic

11365, 11755, 12049

Vision

10037

Zepto

11585

Vistron

11363

TEAC

Zonda

10698

Vivax

11709

Technics

10556

Thomson

10625

Vizio

11758, 12209

VCR

Vortec

10037

DirecTV

20739

DVD

Voxson

10178, 10037

Humax

20739

3D LAB

30539

11365, 12098

Panasonic

20616

Accurian

30675

Toyoda

11709

Walker

11667

Philips

20739

Acoustic Solutions

30713

TRANS-continents

10556, 10037, 10668,
11037

Waltham

10037, 10668, 11037

ReplayTV

20616

AEG

30675

Wansa

12098

Sonic Blue

20616

Transonic

10037, 10698, 10512,
11363

AFK

31152

Wards

10178

TiVo

20739

Aiwa

30533

Triad

10556

Watson

10037, 10714, 10668,
11037

PVR

Akai

30675

Trio

11248

10037

DirecTV

20739

Triumph

10556, 10037

Welltech

10714, 11652

Humax

20739

TVTEXT 95

10556

Weltstar

11037

Panasonic

20616

Uher

10037

Westinghouse

11755

Philips

20739

Wega

Alba

30539, 30713

Ambiance

33052

Amstrad

30713

Anthem

32820

Remote Control Codes
DVD

DVD

Aristona

30539, 30646

Elfunk

30713

Kennex

30713

Orion

30713

ASDA

32213

Elite

31152

Kenwood

30490, 30534

Ormond

30713

Audix

30713

Emerson

30675, 32213

Lenco

30713, 33052

Pacific

30713

Autovox

30713

EuroLine

30675

Lexicon

32545

Palladium

30713

Awa

32587

Ferguson

30713

30741, 31602

Panasonic

Basic Line

30713

Finlux

30741

Limit

33052

Bel Canto Design

31571

Firstline

30713

Lodos

30713

30503, 30490, 31579,
31641, 32523, 32710,
32859

Black Diamond

30713

Foehn & Hirsch

33052

Loewe

Blue Parade

30571

Funai

30675

30539, 30741, 32474,
32783

Blue Sky

30713

30522

Logik

30713

Brandt

30503

GFM

30675

Lumatron

30741, 30713
30741

Pelican Accessories

30533

Philco

30675

Philips

30503, 30539, 30646,
30675, 30713, 31340,
31354, 32056, 32084,
32434, 32689

Pioneer

30571, 30142, 30631,
31571, 32442, 32860
30539

Bush

30713

Global Sphere

31152

Lunatron

C-Tech

31152

Go Video

30741

Luxman

30573
30713
30503, 30539, 30646,
30675, 30713, 31354

Polk Audio
Presidian

30675

Manhattan

30713

ProAudio

31394

Marantz

30539, 32414, 32432,
33444

Proscan

30522

Proson

30713

Pye

30539, 30646

California Audio Labs 30490

GoldStar

30741

Luxor

Cambridge Audio

Goodmans

30713, 31152

Magnavox

Centrum

32808
30675, 30713

GPX

30741

Changhong

30627

Grandin

30713

Cinetec

30713

Grundig

30539, 30713

Clatronic

30675

H&B

30713

Clayton

30713

Haaz

31152

Crown

30713

Hanseatic

30741

Dantax

30539, 30713

Harman/Kardon

30582, 31229, 33228

Denon

30490, 30634, 31634,
32258, 32748

Henss

30713

Hitachi

30573, 30713, 31664

Dick Smith
Electronics

31152

Hoeher

30713

Digihome

30713

HotMedia

31152

DigiLogic

30713

Humax

30646

Digix Media

31394

Inno Hit

30713

Disney

30675

Insignia

30741, 30675, 32428,
32596

DSE

30675, 31152

Dual

30713

Integra

30503, 30571, 30627,
31612, 31634, 32147

Mark

30713

Matsui

30713

Maxim

30713

MDS

30713

Medion

30630, 30741

Memorex
Metz

Radionette

30741

Radiotone

30713

RCA

30522, 30571, 32213,
32587

32213

REC

30490

30571, 30713

Red

32213

Micromedia

30503, 30539

Redstar

31394

Micromega

30539

Roadstar

30713

Microsoft

30522, 32083

Rotel

30623

Minax

30713

Salora

30741

Mitsubishi

30713

Samsung

Momitsu

33052

30490, 30573, 30199,
30820, 31635, 32069,
32329, 32489, 33195
30713

Durabrand

30675, 30713

Irradio

30646

NAD

30741

Dynex

32596

JVC

NEC

30741, 31602

Sanyo

Dyon

33052

30539, 30646, 30713

31152

30503, 30627, 31612,
32147, 30571, 31634

Schneider

eBench

30503, 30539, 30623,
30867, 31597, 31602,
32855

Schoentech

30713

Oppo

30575, 32545

Scott

31394

Kendo

Onkyo

Remote Control Codes
DVD

DVD

SEG

30713

Semp

30503

Sharp

30630, 30675, 30713,
32250, 32474, 32652,
32869

Sherwood

Blu-ray Disc

DVD-R

30503, 31639, 32277,
32551, 32705, 33157

JVC

32855

Irradio

Lenco

33052

JVC

31597

Transonic

31394

Lexicon

32545

30741

TVE

30713

30741, 31602

Loewe

30741

United

30675, 30713, 31152

30741, 33052

Limit

33052

Magnavox

30646, 30675

Universum

30741, 30713

Shinsonic

30533

Loewe

32474, 32783

Medion

30741

Urban Concepts

30503

Silva Schneider

30741

Magnavox

30675

Panasonic

Vestel

30713

31152

32414, 32432, 33444

30490, 31579, 32523,
32710, 32859

SilverCrest

Marantz

Victor

31597

33052

30646, 31340

30539, 30713

Momitsu

Philips

Skantic

Vizio

32563

30631, 32860

SM Electronic

31152

Vtrek

32587

Pye

30646

Smart

30713

Waltham

30713

32147, 32900, 32910,
33100, 33101, 33500,
33501

Pioneer
RCA

30522

Sony

30533, 30864, 31033,
31070, 31431, 31516,
31633, 32180

Wellington

30713

Oppo

32545

Samsung

30490, 31635

Weltstar

30713

Panasonic

31641, 32523, 32859

Schneider

30646

Wharfedale

30713

Philips

32084, 32434, 32689

Sharp

30630, 30675, 32869

Windsor

30713

Pioneer

30142, 32442

Sony

Windy Sam

30573

Samsung

30199, 33195

31033, 31070, 31431,
31516, 31633, 32180

30522, 32083

Sharp

32250, 32474, 32652

Sylvania

30675

XLogic

31152

Sherwood

33052

Targa

30741

Yamaha

30490, 30539, 30646,
30817, 31354, 32298,
32299

Sony

31516, 32180

Toshiba

31639, 32277, 32551

Sylvania

30675

Victor

31597

TASCAM

34004

Yamaha

30646

30503, 30741

Toshiba

32551, 32705, 33157

Zenith

30741

Vizio

32563

Yamaha

32298, 32299

Soundwave

30713

Star Clusters

31152

Strato

31152

Strong

30713

Supervision

31152

Sylvania

30630, 30675

Symphonic

30675

Toshiba

Xbox

Onkyo

30646

Tamashi

31394

Tandberg

30713

Targa

30741

Blu-ray Disc

Tchibo

30741

Ambiance

33052

TCL

32587

Anthem

32820

DVD-R

TCM

30741

Cambridge Audio

32808

Accurian

TEAC

34004, 30571, 30741,
30675, 31394

Denon

32258, 32748

Aristona

Dyon

33052

Technica

30713

Denon

30490

Foehn & Hirsch

33052

Technics

30490

Emerson

30675

Funai

30675

30713

30675

TV/DVD Combination

Techwood

Funai

Harman/Kardon

33228

30741

11675

30713

Go Video

Akai

Teletech

Insignia

30675, 32428, 32596

11037, 30713

Theta Digital

30571

30741

Black Diamond

Integra

11037, 30713

30522

31664

Blue Sky

Thomson

32147, 32900, 32910,
33100, 33101, 33500,
33501

30646

Bush

11037, 10698, 12719,
30713

Zenith

GPX
Hitachi
Humax

HD-DVD
Integra

32901, 33104, 33504

30741

30675

Microsoft

32083

30646

Onkyo

32901, 33104 33504

Xbox

32083

Remote Control Codes
TV/DVD Combination

TV/DVD Combination

Centrum

11037, 30713

Sunstech

12001

Crown

11037, 30713

Sylvania

10171, 11394, 11864,
11886, 30630, 30675
10698

DMTech

12001

Dual

11037, 30713

TEAC

12049

Technica

11037, 30713

Elfunk

11037, 30713

Telefunken

10698

Emerson

11394, 11864, 11886,
30675

Teletech

11037, 30713

Thomson

10625

Ferguson

11037, 30713

Toshiba

11524

Goodmans

11037, 30713

United

11037, 30713

Grandin

30713

Universum

30713

Grundig

30539

Vestel

11037

H&B

12001

Viewsonic

12049

Hanseatic

12001

Weltstar

11037, 30713

Hitachi

11037, 11667, 30713

Dynex

Insignia

12049

JVC

12271

11423

Logik

11037, 30713

Luxor

11037, 30713

Magnavox

12372

Matsui

11037, 30713

Medion

12719

Nordmende

12001

Odys

12719

Panasonic

12170

Philips

11454, 10556, 11394,
30539

Powerpoint

10698

Prosonic

12001

Pvision

12001

RCA

12746, 12932

Schaub Lorenz

12001

SEG

11037, 12719, 30713

Sharp

10818

Soniq

12493

Remote Control Codes

Memo

* 2 9 4 0 1 4 7 1 C O D E *

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2013:03:13 18:56:03+09:00
Modify Date                     : 2013:03:13 20:26:47+09:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2013:03:13 20:26:47+09:00
Format                          : application/pdf
Document ID                     : uuid:c15fda23-03a8-4076-810a-440bff119ac5
Instance ID                     : uuid:1d748443-0f03-46d7-8c7e-bf0937803733
Page Layout                     : SinglePage
Page Mode                       : UseOutlines
Page Count                      : 140

EXIF Metadata provided by EXIF.tools

Onkyo Tx Nr626 Owner S Manual

TX-NR626 to the manual 15712385-f5a8-45dd-86eb-9540272f5688

Navigation menu

Versions of this User Manual:

Views

Navigation