Onset Computer ENDPOINT 802.15.4 Networking Device - Endpoint User Manual Visio Simplenet QSG1 vsd
Onset Computer Corporation 802.15.4 Networking Device - Endpoint Visio Simplenet QSG1 vsd
Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1044026 |
| Application ID | +jn5RLJP1qZbhRt6rclBLg== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 17.57kB (219582 bits) |
| Date Submitted | 2008-12-15 00:00:00 |
| Date Available | 2008-12-16 00:00:00 |
| Creation Date | 2008-12-10 16:23:33 |
| Producing Software | Acrobat Distiller 8.1.0 (Windows) |
| Document Lastmod | 2008-12-10 16:23:33 |
| Document Title | Visio-Simplenet-QSG1.vsd |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | JBean |
HOBOnodeÂŽ System Quick Start Guide Follow the steps in this Quick Start Guide to setup a HOBOnode system. Components The HOBOnode System includes: - 1 HOBOnode Receiver - HOBOnode(s) - HOBOnode Repeater(s) (Optional) Step 1 - Connect HOBOnode Receiver Connect the receiver to the base PC. Put the receiver into the base and mount vertically or lay horizontally on a desk. Make sure the antenna is pointing upward. Topology The following diagrams show two basic topologies. Step 2 - Activate Devices You must push the Activate button on HOBONodes and Repeaters to enable them. Remove the cap and locate the brown button. Hold it down for 2 seconds. The LEDs will flash briefly to indicate that the device is activated. Activating HOBONodes Activating Repeaters Part# MAN_HOBOnode-QS Document # 12537-A Step 7 - Deploy HOBOnode Repeaters (if required) Step 3 - Discover Nodes Open HOBOnode Viewer and click the AutoSearch. The receiver will search for 4 minutes for any HOBOnodes or HOBOnode Repeaters within its range. The yellow Search LED on the receiver will blink while searching. If you have HOBOnodes outside of range due to distance or Line of Sight restriction, you will need to use a HOBOnode Repeater. Connect the antennas to the HOBOnode Repeater as shown below. Step 8 - Verify Connection to HOBOnode and Receivers After you have deployed the units, perform an AutoSearch again using Campfire to make sure that all the HOBOnodes and Repeaters can still connect to the HOBOnode Receiver. You may need to reposition the units and AutoSearch again to achieve the connection. Step 4 - View Node Information In Campfire, select the Serial Number tab to view information about each node. FCC Compliance Step 5 - View Plots This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. In Campfire, select the Node Plots tab to view data plots. Changes or modifications not expressly approved by Onset Computer Corporation could void the user's authority to operate the equipment. Step 6 - Deploy HOBOnodes To comply with FCC and Industry Canada RF radiation exposure limits for general population, the HOBOnode Receiver and the HOBOnode Repeaters must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Deploy HOBOnodes in desired locations. Attach the mounting bracket to a wall, post, or tree, then insert HOBOnode into bracket. Make sure the cable is hanging down and create a drip-loop. Canada This device has been designed to operate with the antennas listed below, and having a maximum gain of 15 dB. Antennas not included in this list or having a gain greater than 15 dB are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Maximum Allowed Antenna Gain Max Gain Part W-RCVR-USB 5 dBi W-REPEATER Local Antenna (Omni-Directional): 5 dBi Long Distance Antenna (Directional): 15 dBi
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Producer : Acrobat Distiller 8.1.0 (Windows) Creator Tool : PScript5.dll Version 5.2 Modify Date : 2008:12:10 16:23:33-05:00 Create Date : 2008:12:10 16:23:33-05:00 Format : application/pdf Title : Visio-Simplenet-QSG1.vsd Creator : JBean Document ID : uuid:fddba50e-e91d-4194-ad45-af30f7047fca Instance ID : uuid:1d343709-a2e1-40ac-8d81-0b36218314f1 Page Count : 2 Author : JBeanEXIF Metadata provided by EXIF.tools