Opticon Sensors Europe H29 Mobile computers User Manual
Opticon Sensors Europe BV Mobile computers
User manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3772374 |
| Application ID | K5K3wvmRI7pZpRqkYLRsew== |
| Document Description | User manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 438.3kB (5478791 bits) |
| Date Submitted | 2018-03-07 00:00:00 |
| Date Available | 2018-09-03 00:00:00 |
| Creation Date | 2018-03-06 09:41:54 |
| Producing Software | Adobe PDF Library 15.0 |
| Document Lastmod | 2018-03-06 09:42:16 |
| Document Title | User manual |
| Document Creator | Adobe InDesign CC 13.0 (Windows) |
Charging Instructions Battery Installation The H-29(EU) battery pack is initially not fully charged. After installing the battery pack, please charge it via the USB cable or via the charging cradle. By default, the battery pack is not installed in the H-29(EU) at the factory to avoid damage caused by excessive draining. Annual replacement of the battery pack can avoid possible risks or abnormalities and ensures maximum performance. Do not store fully charged or (almost) empty batteries for long periods of time. We recommend charging the spare battery pack every two to three months to keep its charge at a moderate level to maximize battery life. H-29 H-29EU Mobile Computer 1. 2. 3. Quick Start Guide 4. 5. 6. 7. Earphone connector Power button Scan button Front View Please remove the hand strap first when opening the battery compartment. Push the battery cover lock switch to open position then remove the battery cover. Please make sure that the battery contacts are properly aligned with the contacts of the terminal. Close the battery cover and push the cover lock switch to lock. Volume up Volume down Scan button USB connector 1. Battery slot 2. Battery pack 3. Battery cover Back View CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. Confirm what is in the Box -- H-29/H-29EU A mobile computer with a barcode scanning feature. -- USB cable Charge/Communication cable & quick charge compliant power adapter. -- Battery box With rechargeable battery. -- Hand strap -- Quick Start Guide Provides product information and instructions. DISPOSE OF USED BATTERIES ACCORDINGTO LOCAL REGULATIONS BC * The number of accessories may differ depending on the product configuration. If any of the accessories are damaged or missing, please contact your local representative. Charging Time The required charging time depends on the actual application running on the H-29(EU) and the condition of the battery pack. The H-29(EU) is shipped with a Lithium-ion battery but not fully charged. Please fully charge it before the 1st time use. 1. Logo and indicator area 2. Android function key area (Back, Home, Menu key) 1. 2. 3. 4. 5. 6. 7. 8. General View Battery contact SIM card slot (H-29EU model) Micro SD card slot Battery cover lock switch Hand strap hook Speaker Flash LED Camera Keypad Charging via USB Cable Use the provided USB charge & communication cable together with the quick charge compliant power adapter to charge the H-29(EU). Charging via Charging Cradle Connect the cradle with a power adapter to a power outlet. Place the H-29(EU) on the cradle for charging. SD / SIM Card Installation (H-29EU model) Top View Bottom View 1. Scan Window 1. Cradle IO connect 1. 2. 3. 4. 5. 6. 7. 8. Enter Back space → Key ↓ Key Scan key ↑ Key ← Key Esc 9. 10. 11. 12. 13. Tab Orange change Blue change * Key # Key 1. 2. 3. 4. 5. 6. 7. 8. 9. Turn off the H-29EU or put it in battery swap mode Remove the battery cover Remove the battery by pulling the tab on the end of the battery Lift the retaining door Please see the back view Insert the micro SD card into the left slot Insert the SIM card into the right slot Insert the battery pack into the battery compartment Restore the battery cover and lock the battery cover lock switch Barcode Data Capture To scan a barcode label: 1. Point the scan window at the barcode. 2. Tap scan on the screen or press one of the scan buttons on the H-29(EU). The imager will project a green aiming bar. The green aiming bar is used to position the barcode or object within the field of view of the imager. 3. Ensure the entire barcode is within the width area formed by the green aiming bar, then either wait for the timeout or release the scan key to capture the image. A white beam will illuminates the barcode to capture and decode it. FCC Compliance for H-29 This Device complies with Part 15 of the FCC rules, operation is subject to the following two conditions: (1) This device may not cause harmful interference and, (2) This device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. 15.21 Statement You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 1cm between the radiator and your body. General Safety Rules Please read this Guide thoroughly and carefully before you start using this device. Use only the components and accessories supplied by the manufacturer for H-29(EU) you are using. Do not attempt to disassemble H-29(EU), as it does not contain parts that can be repaired by the user. Any tampering will void the warranty. When replacing the battery pack or at the end of life of H-29(EU) disposal must be performed in compliance with the laws in force in your jurisdiction. Do not submerge H-29(EU) in any liquid (water, detergent, etc). For Safe Use Concern, Please Pay Special Attention on the Following Notices: The manufacturer has taken safety as first priority during design stage. To avoid any potential accident, please be cautious on the following alert points: • Please do not stock this device under conditions of high temperature which will cause the battery to become hot, fire, or broken etc. leading to failure and safety concerns. • When the charging time is noticed longer than standard required (CHARGING LED, RED, is still ON), please stop charging immediately. • Please charge this device in place without any water-spray or moisture. • Ensure that the AC adapter can freely dissipate its heat, don’t cover the AC adapter with objects, such as curtains. • Never use damaged AC adapters, immediately replace it with a new approved AC adapter. • Please do not put any heavy weight on top of this device as it might cause device enclosure crack then lead to cutting injury. • Please do not use wet hand to pull out the AC adapter which might cause electric shock. • Please do not use H-29(EU) AC adapter on any other different devices. • Please do not put the device into water which may cause shortcircuit or fire. • Please do not put this device in place close to open fire. • If the power or USB cable is seriously twisted or broken, please stop using immediately or it may cause electric shock, short-circuit, or fire. • Please stop using immediately when there is any unusual smell or overheat during charging or operation. • Please stop using immediately when there is any liquid or dew on the device. • Please do not use the AC adapter outdoor. Please do not wrap the AC adapter with cloth which will block heat dissipation and will cause electric shock or fire. • Except charging, please remove the AC adapter plug from the wall AC outlet socket or it will cause fire accident. Important Notices When Using • Before replacing battery pack due to failure, shortened life, or any other unusual behavior, please confirm if the device has been used correctly and there has no user operation issue involved. • It is possible there will be some missed data or interference encountered during the wireless transmission. It is not a situation can be controlled by the manufacturer. • Please do not use any alcohol, benzene, organic solvent, cleaner liquid, or steel-wool on the surface of this device. • Please do not scratch the surface of Scan Window in any way as which will cause problem on barcode scanning. Audio Safety To prevent possible hearing damage, do no listen at high volume for long periods. European Union Regulatory Notes Hereby, Opticon Sensors Europe B.V. declares that the radio equipment type H-29(EU) is in compliance with Directive 2014/53/ EU. The WiFi operating in the bands 5150 – 5350 MHz shall be restricted to indoor use for the following countries: AT, BE, BG, CH, CY, CZ, DE, DK, EE, EL, ES, FI, FR, HR, HU, IE, IS, IT, LI, LT, LU, LV, MT, NL, NO, PL, PT, RO, SE, SI, SK, TR, UK. The full text of the Declaration of Conformity is available at the following internet address: https://opticon.com/product/h-29/ SAR Compliance (H-29EU) SAR Information (for EU): Head: 0.328 W/kg@ 10g (CE) Body: 1.600 W/kg@ 10g (CE) SAR Compliance (H-29) SAR Information (for EU): Head: 0.288 W/kg@ 10g (CE) Body: 0.320 W/kg@ 10g CE) Body - worn Operation This device was tested for typical body-worn operations. A minimum separation distance must be maintained between the user’s body and the handset, including the antenna: 0.5 cm to comply with the RF exposure requirements in Europe third-party belt-clips, holsters and similar accessories used by this device should not contain any metallic components. Body-warn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Power and Frequency Ranges H-29EU Frequency Maximum Output 4dBm 4dBm 17dBm 21dBm 22dBm 32dBm 30.5dBm 24dBm 24dBm 23dBm 23dBm 23dBm 23dBm 23dBm 24dBm 23dBm Radio Type Description Bluetooth Bluetooth BR+EDR Bluetooth 4.0-LE 2.4GHz 5GHz Radio Type Description Frequency Maximum Output Bluetooth Bluetooth BR+EDR 2400~2483.5 MHz 4dBm Bluetooth 4.0-LE 2400~2483.5 MHz 4dBm 2.4GHz 2400~2483.5 MHz 17dBm 5GHz 5150~5350 MHz 21dBm 5470~5725 MHz 22dBm 2400~2483.5 MHz 2400~2483.5 MHz WLAN 2400~2483.5 MHz 5150~5350 MHz 5470~5725 MHz GSM GSM 900 880~915 MHz GSM 1800 1710~1785 MHz WCDMA WCDMA Band I 1920~1980 MHz WCDMA Band VIII 880~915 MHz LTE LTE Band 1 1920~1980 MHz LTE Band 3 1710~1785 MHz LTE Band 7 2500~2570 MHz LTE Band 8 880~915 MHz LTE Band 20 832~862 MHz LTE Band 38 2570~2620 MHz LTE Band 40 2300~2400 MHz other NFC 13.56 MHz GPS 1575.42 MHz H-29 WLAN other NFC 13.56 MHz Documentation Documentation, drivers and software updates for the H-29(EU) are available at:www.opticon.com Opticon Sensors Europe BV Opaallaan 35, 2132 XV Hoofddorp, the Netherlands. © Copyright Opticon. All rights reserved. This information is subject to change without prior notice. For availability, contact your local representative.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Language : nl-NL XMP Toolkit : Adobe XMP Core 5.6-c143 79.161210, 2017/08/11-10:28:36 Create Date : 2018:03:06 09:41:54+01:00 Metadata Date : 2018:03:06 09:42:16+01:00 Modify Date : 2018:03:06 09:42:16+01:00 Creator Tool : Adobe InDesign CC 13.0 (Windows) Instance ID : uuid:b645b381-339d-4fac-bfcb-e6bc846d370c Original Document ID : xmp.did:e8d74682-ca96-e144-90d5-67646336dd9f Document ID : xmp.id:43fffbe2-60f8-034d-96c7-f8a48d2dd487 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:6b40f0f1-f64a-ac42-a3f2-07d11fecb3ff Derived From Document ID : xmp.did:95296de3-49bc-5241-96e5-211c305e9c91 Derived From Original Document ID: xmp.did:e8d74682-ca96-e144-90d5-67646336dd9f Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 13.0 (Windows) History Changed : / History When : 2018:03:06 09:41:54+01:00 Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Page Count : 2 Creator : Adobe InDesign CC 13.0 (Windows)EXIF Metadata provided by EXIF.tools