Optimus Ctr 114 Users Manual

CTR-114 to the manual 514b97e7-cc03-475e-8210-ff96572866bc

2015-02-05

: Optimus Optimus-Ctr-114-Users-Manual-496851 optimus-ctr-114-users-manual-496851 optimus pdf

Open the PDF directly: View PDF .
Page Count: 36

Cat. No. 14-1120

OWNER’S MANUAL

Please read before using this equipment.

CTR-114

Auto Reverse

Voice-Activated

Cassette Recorder

with Two-Speed

Recording

14-1120.fm Page 1 Wednesday, January 19, 2000 4:27 PM

FEATURES

Your Optimus CTR-114 Auto-Reverse Voice-Activat-

ed Cassette Recorder offers the greatest conve-

nience in recording technology. You can have

recording begin and end according to the sound level

in a room, which gives you hands-free operation

while recording. The CTR-114’s microphone is sensi-

tive enough for the boardroom, a seminar, or a lec-

ture hall. And it’s small enough to fit in your briefcase

or purse, so it can go wherever you go.

The CTR-114’s other features include:

Two-Speed Recording — lets you record at normal

or extended speed to maximize your recording time.

Automatic Reverse — automatically changes the

tape direction at the end of a tape side so you can

continuously play or record both sides of a cassette

tape.

Voice Activated Recording — lets you choose

hands-free operation which saves tape.

Voice Zoom Switch — lets you record voice sounds

clearly and reduce noises outside the voice range.

Optimus and RadioShack are registered

trademarks used by Tandy Corporation.

14-1120.fm Page 2 Wednesday, January 19, 2000 4:27 PM

Playback Speed Control — lets you adjust the play-

back speed of your tape.

Built-in Microphone — lets you make quality re-

cordings without having to use an external micro-

phone.

External Microphone Jack — lets you connect an

optional external microphone for unidirectional re-

cording, reducing background noise.

One-Touch Recording — lets you start recording

with the press of a button.

Cue/Review — lets you listen to recordings at high

speed to help you find a particular section and stop

there.

Mic Sensitivity Switch — lets you select low or high

microphone sensitivity for recording specific sounds,

like a one-on-one interview, or for recording broader

sounds, as in a lecture hall.

Tape Direction Control — lets you change the

tape’s direction at any time without having to eject

the tape and turn it over.

Battery Check Indicators — show you the amount

of power remaining in the batteries.

14-1120.fm Page 3 Wednesday, January 19, 2000 4:27 PM

Tape Counter — helps you quickly find a specific

section on the cassette. It resets with the touch of a

button.

Automatic Level Control — automatically sets the

correct recording level.

Three Power Sources — let you power your cas-

sette recorder from internal batteries (not supplied),

standard AC power (with an optional AC adapter), or

your vehicle’s battery (with an optional DC adapter).

Automatic Shut-Off Mechanism — automatically

shuts off the recorder at the end of the reverse side

of the tape while playing or recording.

We recommend you record the CTR-114’s serial

number here. The number is on the label inside the

cassette compartment.

Serial Number: ___________________________

14-1120.fm Page 4 Wednesday, January 19, 2000 4:27 PM

CONTENTS

Preparation ........................................................... 6

Connecting Power .......................................... 6

Using Battery Power ................................ 6

Using AC Power ...................................... 9

Using Vehicle Battery Power ................. 11

Connecting an Earphone .............................. 13

Listening Safely ..................................... 14

Traffic Safety .......................................... 14

Connecting an External Microphone ............ 15

Attaching the Wrist Strap .............................. 16

Operation ............................................................ 17

Loading a Cassette Tape .............................. 17

Recording ..................................................... 18

Playing a Cassette Tape ............................... 23

Using Fast Forward and Rewind ........... 27

Using the Tape Counter ................................ 28

Tape Tips ...................................................... 29

Erasing Tapes ........................................ 29

Preventing Accidental Erasure .............. 29

Restoring Tape Tension

and Sound Quality ................................. 30

Care and Maintenance ....................................... 31

Cleaning the Tape-Handling Parts ................ 32

Specifications .................................................... 34

14-1120.fm Page 5 Wednesday, January 19, 2000 4:27 PM

PREPARATION

CONNECTING POWER

You can power your CTR-114 from:

• internal batteries

• AC power (with an optional AC adapter)

• vehicle battery power (with an optional DC

adapter)

Note: Connecting an adapter automatically discon-

nects internal batteries.

Using Battery Power

You can power the CTR-114 with two AA batteries

(not supplied). For the best performance and longest

life, we recommend alkaline batteries, such as Ra-

dioShack Cat. No. 23-557.

You can also use rechargeable nickel-cadmium bat-

teries (Cat. No. 23-125). These batteries and a bat-

tery charger (Cat. No. 23-133) are available at your

local RadioShack store.

14-1120.fm Page 6 Wednesday, January 19, 2000 4:27 PM

Cautions:

• Use only fresh batteries of the required size and

recommended type.

• Do not mix old and new batteries, different types

of batteries (standard, alkaline, or recharge-

able), or rechargeable batteries of different

capacities.

Follow these steps to install batteries.

1. Press down and slide the battery compartment

cover in the direction of the arrow, then lift open

the cover.

2. Put the batteries in the compartment as indi-

cated by the polarity symbols (+ and –) marked

outside the compartment.

3. Close the cover.

14-1120.fm Page 7 Wednesday, January 19, 2000 4:27 PM

The CTR-114 has three colored battery indicators

which show how much power is left in the batteries.

The battery indicators light when you press STOP,

PLAY, RECORD, or .

When the red (L) battery indicator lights, replace both

batteries.

Caution: Always dispose of old batteries promptly

and properly. Do not burn or bury them.

BATTERY

Indicators

Green ➜

F (full)

Orange ➜

M (medium)

Red

L (low)

14-1120.fm Page 8 Wednesday, January 19, 2000 4:27 PM

Important: This product is capable of using re-

chargeable nickel-cadmium batteries. At the end of a

nickel cadmium battery’s useful life, it must be recy-

cled or disposed of properly. Contact your local,

county, or state hazardous waste management au-

thorities for information on recycling or disposal pro-

grams in your area. Some options that might be

available are: municipal curbside collection, drop-off

boxes at retailers such as your local RadioShack

store, recycling collection centers, and mail-back

programs.

Using AC Power

To power the cassette recorder from a standard AC

outlet, you need an AC adapter such as Cat. No.

273-1663.

Cautions:

• You must use an AC adapter that supplies at

least 3 volts DC power and delivers at least 400

mA. Its center tip must be set to negative, and its

barrel plug must properly fit the CTR-114’s DC

3V jack. The recommended adapter meets these

specifications. Using an adapter that does not

meet these specifications could damage the

cassette recorder or the adapter.

14-1120.fm Page 9 Wednesday, January 19, 2000 4:27 PM

• Be sure you connect the adapter to the cassette

recorder before you plug it into the AC outlet,

and unplug the adapter from the AC outlet

before you unplug it from the cassette recorder.

Follow these steps to connect the cassette recorder

to AC power.

1. Set the adapter’s voltage switch to 3V.

2. Insert the adapter’s 3.4 mm outer diameter/1.3

mm inner diameter barrel plug into the adapter’s

cord, with the tip set to negative.

3. Insert the plug into the cassette recorder’s DC 3V

jack.

4. Plug the adapter into a standard AC outlet.

14-1120.fm Page 10 Wednesday, January 19, 2000 4:27 PM

Using Vehicle Battery Power

To power the recorder from your vehicle’s battery,

you need a DC adapter, such as Cat. No. 270-1562.

Cautions:

• You must use a DC adapter that supplies at least

3 volts DC power and delivers at least 400 mA.

Its center tip must be set to negative, and its bar-

rel plug must properly fit the recorder’s DC 3V

jack. The recommended adapter meets these

specifications. Using an adapter that does not

meet these specifications could damage the

recorder.

• Be sure you plug the adapter into the cassette

recorder before you plug it into the cigarette-

lighter socket, and unplug the adapter from the

cigarette-lighter socket before you unplug it from

the cassette recorder.

14-1120.fm Page 11 Wednesday, January 19, 2000 4:27 PM

Follow these steps to power the cassette recorder

from your vehicle’s battery.

1. Set the adapter’s voltage switch to 3V.

2. Insert the adapter’s 3.4 mm outer diameter/1.3

mm inner diameter barrel plug into the adapter’s

cord, with the tip set to negative.

3. Insert the plug into the cassette recorder’s DC 3V

jack.

4. Plug the other end of the adapter into the vehi-

cle’s cigarette-lighter socket.

14-1120.fm Page 12 Wednesday, January 19, 2000 4:27 PM

CONNECTING AN EARPHONE

You can use an optional earphone with a 1/8-inch

(3.5-mm) plug to listen to a tape in privacy. Insert the

earphone’s plug into the cassette recorder’s EAR

jack.

Notes:

• You can also use an earphone during recording

to listen to what the recorder is picking up

through the internal or an external microphone.

(See “Recording” on Page 18.)

• Your local RadioShack store carries a wide

selection of earphones.

14-1120.fm Page 13 Wednesday, January 19, 2000 4:27 PM

Listening Safely

To protect your hearing, follow these guidelines

when you use an earphone.

• Rotate the volume to the lowest setting before

you begin listening. After you begin listening,

adjust the volume to a comfortable level.

• Do not listen at extremely high volume levels.

Extended high-volume listening can lead to per-

manent hearing loss.

• Once you set the volume, do not increase it.

Over time, your ears adapt to the volume level,

so a volume level that does not cause discomfort

might still damage your hearing.

Traffic Safety

Do not wear an earphone while operating a motor ve-

hicle or riding a bicycle. This can create a traffic haz-

ard and could be illegal in some areas.

Even though some headphones let you hear some

outside sounds when listening at normal volume lev-

els, they still can present a traffic hazard.

14-1120.fm Page 14 Wednesday, January 19, 2000 4:27 PM

CONNECTING AN EXTERNAL

MICROPHONE

You can connect an external microphone (not sup-

plied) with a 1/8-inch (3.5-mm) plug to the recorder’s

MIC jack. Connecting an external microphone auto-

matically disconnects the built-in microphone.

Note: Your local RadioShack store sells a variety of

microphones.

14-1120.fm Page 15 Wednesday, January 19, 2000 4:27 PM

ATTACHING THE WRIST STRAP

Attach the supplied wrist strap to the CTR-114 to

make it easier to carry and to reduce the risk of acci-

dentally dropping it.

Thread the strap’s small loop around the metal pin on

the corner of the CTR-114. Then insert the opposite

end of the strap through the slim loop and pull it until

the slim loop tightens around the metal pin.

Hint: If you have difficulty threading the slim loop

around the medal pin, use the end of a straightened

paper clip to hook onto the loop and pull it through.

14-1120.fm Page 16 Wednesday, January 19, 2000 4:27 PM

OPERATION

You can use the recorder to play normal bias, high-

bias, and metal tapes. However, you should only use

normal bias (Type I) tapes for recording. If you record

on metal or high-bias tapes, the recorded sound will

not erase properly.

LOADING A CASSETTE TAPE

1. Take up any slack in the tape by turning the cas-

sette’s hub with a pencil. Do not touch the

exposed tape.

2. Lift open the cassette compartment door.

14-1120.fm Page 17 Wednesday, January 19, 2000 4:27 PM

3. Insert a cassette into the door’s tape guides with

the cassette’s open edge facing up.

4. Close the door.

RECORDING

You can record using the built-in microphone or an

optional external microphone. For the best perfor-

mance, use any normal bias (Type I) tape up to 90

minutes long. We do not recommend 120-minute

tapes because they are thin and can easily tangle.

Notes:

• The ALC (Automatic Level Control) circuit auto-

matically sets the recording level.

• If you set DIRECTION to REV, the cassette

recorder records on only the reverse side and

stops at the end of that side.

14-1120.fm Page 18 Wednesday, January 19, 2000 4:27 PM

• If you want to record on only one side of a tape,

load the tape so the side you want to record on

faces inside the cassette compartment, set

DIRECTION to REV

, then start the recording.

Caution: If you load a cassette with the erase-pro-

tection tabs broken off, do not try to force down

RECORD. This can damage the recording mecha-

nism. (See “Preventing Accidental Erasure” on

Page 29.)

Follow these steps to record.

1. Load a blank cassette tape, or one you want to

record over, into the cassette compartment.

2. Slide MIC SENSITIVITY to LO or HI, depending on

the sound source you want to record.

LO (Low): Select LO when the sound source is

near the recorder.

HI (High): Select HI when the sound source is far

from the recorder, as in a board room, a semi-

nar, or a lecture hall.

14-1120.fm Page 19 Wednesday, January 19, 2000 4:27 PM

3. To record specific voices without background

interference, slide VOICE ZOOM to ON. The CTR-

114 cuts off higher and lower frequency signals

(background noise) and enhances the mid-

range.

4. Slide

REC SPEED to NORM for normal recording,

or to EXT for extended recording (twice the nor-

mal recording time). At the EXT setting, the

recorder puts the recording in half the space

used during normal speed.

Note: Tapes recorded at the EXT setting can

play only on this recorder or on another recorder

that has the extended recording feature.

14-1120.fm Page 20 Wednesday, January 19, 2000 4:27 PM

5. Set VOX to OUT if you want to manually start and

stop recording. Or, set VOX to IN to use voice-

activated recording.

At the VOX setting, recording begins when the

recorder picks up sound and stops a few sec-

onds after the sound stops.

Hint: The voice-activated feature saves power

and tape if there are long or frequent pauses in

the material you are recording.

6. Press RECORD when you want to begin record-

ing. RECORD and PLAY automatically lock down.

14-1120.fm Page 21 Wednesday, January 19, 2000 4:27 PM

If VOX is set to OUT, recording begins immedi-

ately. If VOX is set to IN, recording begins when

the recorder picks up sound.

Note: To pause recording, slide PAUSE in the

direction of the arrow. To resume recording, slide

PAUSE to the other position.

7. If you set VOX to IN, adjust VOX SENS to set the

sound level at which recording begins. When

you adjust VOX SENS higher, softer sounds start

VOX recording. When you adjust VOX SENS

lower, louder sounds start VOX recording.

14-1120.fm Page 22 Wednesday, January 19, 2000 4:27 PM

Notes:

• The CTR-114 records on one side of the tape,

automatically reverses the tape’s direction,

records on the reverse side of the tape, then

automatically stops.

• You can use an earphone (not supplied) to

monitor a recording in progress.

8. To stop recording before it automatically stops,

press STOP

PLAYING A CASSETTE TAPE

1. Switch DIRECTION to FWD to play the side of the

cassette facing out, or to REV to play the side

facing in.

14-1120.fm Page 23 Wednesday, January 19, 2000 4:27 PM

2. Set the auto reverse switch in the cassette com-

partment to either one-time or continuous play-

back.

One-Time Playback: plays one side of

the tape to its end, then automatically reverses

the tape’s playback direction, plays the reverse

side of the tape, then automatically stops.

Notes:

•If you set DIRECTION to REV, the cassette

recorder plays only the reverse side and stops

at the end of that side.

• If you move DIRECTION from REV to FWD dur-

ing playback, the cassette recorder stops.

Continuous Playback: plays both sides

of the tape continuously until you press STOP

14-1120.fm Page 24 Wednesday, January 19, 2000 4:27 PM

3. Press PLAY . The button locks down and the

tape plays.

Note: Slide REC SPEED to NORM for tapes that

have been prerecorded on other recorders or

recorded with the normal record setting on this

recorder. Or slide REC SPEED to EXT for tapes

that have been recorded with the extended

record setting on this recorder.

4. Turn PLAY BACK SPEED toward FAST to play the

tape more quickly or toward SLOW to play it

more slowly.

14-1120.fm Page 25 Wednesday, January 19, 2000 4:27 PM

5. Adjust VOLUME to the desired listening level.

6. To stop the tape, press STOP

Note: To stop play momentarily, slide PAUSE in

the direction of the arrow. Slide PAUSE to the

other position to resume play.

14-1120.fm Page 26 Wednesday, January 19, 2000 4:27 PM

Using Fast Forward and Rewind

When the tape is stopped, press or to re-

wind or fast-forward it.

To stop the tape, press STOP.

Note: The CTR-114 does not automatically stop

when it reaches the end of the tape. To protect the

tape after the tape has fully wound to either end,

press

STOP to release fast-forward or rewind.

DIRECTION

setting

rewind,

press

To fast-

forward,

press

FWD

REV

14-1120.fm Page 27 Wednesday, January 19, 2000 4:27 PM

You can also hold down or during play-

back to help you locate a specific portion of the tape

(for example, if you are listening for a particular

speech, statement or other audio cue). While holding

it down, you hear the tape at a faster speed. To re-

turn to normal playback, release the button.

USING THE TAPE COUNTER

You can use the tape counter to note different posi-

tions or locations on your tape during recording or

playback. Before playing a tape, press the tape

counter reset button to set the counter to 000.

During play or recording, the numbers advance to

show the amount of tape that has moved past the

tape heads since the tape began moving. When the

tape rewinds, the numbers decrease.

14-1120.fm Page 28 Wednesday, January 19, 2000 4:27 PM

TAPE TIPS

Erasing Tapes

If you record on a previously recorded tape, you re-

place the old recording with the new one. If you need

to quickly erase an entire tape, you might prefer to

use a bulk eraser (available at your local RadioShack

store).

Note: If you use metal or high-bias type tape, the re-

corded sound may not be erased properly.

Preventing Accidental Erasure

Cassettes have two erase-protection tabs — one for

each side. When a tab is in place, you can record on

that side.

To prevent accidental erasure of a tape recording,

use a screwdriver to remove one or both of the cas-

sette tape’s erase-protection tabs. This prevents

RECORD from being pressed.

Side A

Side A Tab

14-1120.fm Page 29 Wednesday, January 19, 2000 4:27 PM

If you later decide to record on a tape side after you

have removed its erase-protection tab, place a piece

of strong plastic tape over that side’s erase-protec-

tion hole. Be sure you cover only the hole originally

covered by the erase-protection tab.

Caution: Removing the erase-protection tabs does

not prevent a bulk tape eraser from erasing a cas-

sette tape.

Restoring Tape Tension and Sound

Quality

After you play a cassette tape several times, the tape

might become tightly wound on the reels. This can

cause playback sound quality to deteriorate.

To restore the sound quality, fast-forward the tape

from the beginning to the end of one side, then com-

pletely rewind it. Then loosen the tape reels by gently

tapping each side of the cassette’s outer shell on a

flat surface.

Caution: Be careful not to damage the cassette

when tapping it. Do not touch the exposed tape or al-

low any sharp objects near the cassette.

14-1120.fm Page 30 Wednesday, January 19, 2000 4:27 PM

CARE AND MAINTENANCE

Your Optimus CTR-114 Auto-Reverse Voice-Activat-

ed Cassette Recorder is an example of superior de-

sign and craftsmanship. The following suggestions

will help you care for the cassette recorder so you

can enjoy it for years.

• Keep the recorder dry. If it gets wet, wipe it dry

immediately. Liquids might contain minerals that

can corrode the electronic circuits.

• Use and store the recorder only in normal tem-

perature environments. Temperature extremes

can shorten the life of electronic devices, dam-

age batteries, and distort or melt plastic parts.

• Keep the recorder away from dust and dirt,

which can cause premature wear of parts.

• Handle the recorder gently and carefully. Drop-

ping it can cause the recorder to work improp-

erly.

• Use only fresh batteries of the required size and

recommended type. Batteries can leak chemi-

cals that damage your recorder’s electronic

parts.

• Wipe the recorder with a damp cloth occasion-

ally to keep it looking new. Do not use harsh

chemicals, cleaning solvents, or strong deter-

gents to clean the recorder.

14-1120.fm Page 31 Wednesday, January 19, 2000 4:27 PM

Modifying or tampering with the recorder’s internal

components can cause a malfunction and might in-

validate the recorder’s warranty. If your recorder is

not performing as it should, take it to your local Ra-

dioShack store for assistance.

CLEANING THE TAPE-HANDLING

PARTS

Dirt, dust, or particles of the tape’s coating can accu-

mulate on the tape heads and other parts the tape

touches. This can greatly reduce the performance of

the cassette recorder. After every 20 hours of tape

player operation, use a cassette deck cleaning kit or

follow these steps to clean the tape-handling parts.

1. Remove the batteries and disconnect any other

power source.

2. Open the cassette compartment door.

3. Press PLAY to expose the tape-handling

parts.

14-1120.fm Page 32 Wednesday, January 19, 2000 4:27 PM

4. Use a cotton swab dipped in denatured alcohol

or tape head cleaning solution to clean the

record/playback head, pinch rollers, tape guides,

and capstans.

5. When you finish cleaning, press STOP and close

the cassette compartment door. Then reconnect

power.

Your local RadioShack store sells a complete line of

cassette recorder cleaning supplies.

Tape Guides Erase Heads

Capstans

Pinch Rollers

Record/Playback Head

14-1120.fm Page 33 Wednesday, January 19, 2000 4:27 PM

SPECIFICATIONS

CASSETTE DECK

Tape System .............. 2-track, monophonic cassette

Tape Speed ...................................17/8 ips (4.8 cm/s)

Wow and Flutter (WRMS) ................................. 0.2%

Frequency Response (at –3 dB) ..... 250 Hz to 8 kHZ

S/N Ratio ........................................................ 30 dB

Erasing System ................................................... DC

Recording System ....................................... DC Bias

Tape Type ................................ Normal Bias (Type I)

POWER REQUIREMENT

Batteries ............................................ 2 AA Batteries

(Cat. No. 23-557)

AC .................................. 120 Volts with AC Adapter

(Cat. No. 273-1663)

DC .............................. 12 Volts DC with DC Adapter

(Cat. No. 270-1562)

Typical Cassette Playing Time

with AA Alkaline Batteries ................About 16 Hours

w/ Headphones, About 14 Hours w/Speakers

14-1120.fm Page 34 Wednesday, January 19, 2000 4:27 PM

GENERAL

Power Output ............... 15 mW/Channel at 32 ohms

Dimensions (HWD) .............. 41/2 × 35/8 × 11/2 Inches

(112.4 × 89.8 × 37.6 mm)

Weight (without battery) .................................. 7.2 oz

(206 g)

Specifications are typical; individual units might vary.

Specifications are subject to change and improve-

ment without notice.

14-1120.fm Page 35 Wednesday, January 19, 2000 4:27 PM

RadioShack

A Division of Tandy Corporation

Fort Worth, Texas 76102 87-HT6-906-01

980620ACK-0-9

8A8N Printed in Malaysia

Limited Ninety-Day Warranty

This product is warranted by RadioShack against manufacturing defects in ma-

terial and workmanship under normal use for ninety (90) days from the date of

purchase from RadioShack company-owned stores and authorized Ra-

dioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-

dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED

WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DU-

RATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN.

EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY

OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR EN-

TITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DI-

RECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT

OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING,

BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVE-

NIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR

ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,

EVEN IF RadioShack HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES.

Some states do not allow the limitations on how long an implied warranty lasts

or the exclusion of incidental or consequential damages, so the above limita-

tions or exclusions may not apply to you.

In the event of a product defect during the warranty period, take the product

and the RadioShack sales receipt as proof of purchase date to any Ra-

dioShack store. RadioShack will, at its option, unless otherwise provided by

law: (a) correct the defect by product repair without charge for parts and labor;

(b) replace the product with one of the same or similar design; or (c) refund the

purchase price. All replaced parts and products, and products on which a re-

fund is made, become the property of RadioShack. New or reconditioned parts

and products may be used in the performance of warranty service. Repaired or

replaced parts and products are warranted for the remainder of the original

warranty period. You will be charged for repair or replacement of the product

made after the expiration of the warranty period.

This warranty does not cover: (a) damage or failure caused by or attributable to

acts of God, abuse, accident, misuse, improper or abnormal usage, failure to

follow instructions, improper installation or maintenance, alteration, lightning or

other incidence of excess voltage or current; (b) any repairs other than those

provided by a RadioShack Authorized Service Facility; (c) consumables such

as fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or in-

surance costs; or (f) costs of product removal, installation, set-up service ad-

justment or reinstallation.

This warranty gives you specific legal rights, and you may also have other

rights which vary from state to state.

RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite

600, Fort Worth, TX 76102

We Service What We Sell 3/97

14-1120.fm Page 36 Wednesday, January 19, 2000 4:27 PM

Optimus Ctr 114 Users Manual

CTR-114 to the manual 514b97e7-cc03-475e-8210-ff96572866bc

Navigation menu

Versions of this User Manual:

Views

Navigation