Oracle America ENDCAP mTablet RFID/ Imager Module User Manual User Guide

MICROS SYSTEMS, INC mTablet RFID/ Imager Module User Guide

User Guide

Page1of6 Installing the mTablet RFID/Imager Module The following procedure describes how to install the mTablet RFID/Imager Module to MICROS mTablet. 1. Place the mTablet on table. 2. Gently attach the mTablet RFID/Imager Module as shown in figure1. 3. Find the screw holes at mTablet RFID/Imager Module, as figure 2 4. Lastly, place the screws and tighten it with alien key. mTablet mTablet RFID /Imager Module Figure 1Figure 2
Page2of6 Product Information The mTablet RFID/Imager Module have three main functions: • MSR • Scanner • NFC function MSRslotScannerwindowScannerPressButtonNFC(RFID)taparea
Page3of6 Specification Specification Parameter Model mTablet RFID/ Imager Module Rating 3.3 VDC, 50mA (for MSR function) 5VDC, 550mA (for Scanner and NFC function) Weight About 150g Overall Dimension 170mm x 30mm x20.5 mm Storage Temperature -20 to 70 degree Celsius Operating Temperature -10 to 50 degree Celsius Operating Humidity Operating: 95% RH (no condensation) at 50 degree Celsius Storage: 85% RH, non-condensing at 70 degree Celsius Enclosure Material Plastic Scanner Technical Specification Imaging Sensor Resolution: 752 H x 480 V pixels (Wide VGA) Gray Scale: 256 levels (8bits per pixel) Ambient light immunity (Sunlight) 9000 ft. candles (96,900 lux) Laser Safety Class CDRH / IEC Class 2 NFC Function Frequency 13.56MHz FCC ID A4HENDCAP Canada IC ID 9870A-ENDCAP MSR Function 3.3V powered, magnetic card reader
Page4of6 Safety Information SCANNER ENGINE :ThisdeviceemitsCDRH/IECClass2laser.Donotstareintobeam.
Page5of6 EMC RF Information This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Page6of6 Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.

Navigation menu