Oreck Xl U2505Rh Users Manual
U2505RH to the manual 45b27323-6ece-49b7-b457-bde7bcae26d7
2015-02-05
: Oreck Oreck-Xl-U2505Rh-Users-Manual-408754 oreck-xl-u2505rh-users-manual-408754 oreck pdf
Open the PDF directly: View PDF .
Page Count: 8
Download | |
Open PDF In Browser | View PDF |
75812-01 REV A S I M P L Y A M A Z I N G® USER’S GUIDE U2505RH HIGH SPEED UPRIGHT VACUUM CLEANER WITH ® CLEANING SYSTEM •IMPORTANT• SAVE THIS BOOKLET! Includes: • Safety Warnings • Warranty • Operating Instructions • Trouble Diagnosis • Accessories IMPORTANT SAFETY INSTRUCTIONS BEFORE OPERATING CLEANER, READ ALL INSTRUCTIONS IN THIS MANUAL CAREFULLY. When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING Table of Contents Plug Fitting Instructions, Important Safety Instructions . . . . . . Maintenance and Customer Service, Warranty, Accessories . . . . . . . . . . Assembly, To Replace Paper Filter Dust Bag . . . Operating Instructions . . . . . . . . . . How to Replace a Worn Belt, To Adjust or Replace Brush . . . . . . . Stuffing or Blockage, Using an Oreck Fresh Air ® Tab . . . . Troubleshooting Guide . . . . . . . . . . To reduce the risk of fire, electric shock, or injury: • Do not leave appliance unattended when plugged in. Unplug from outlet when not in use and before servicing. • Do not use outdoors or on wet surfaces. • Do not operate the unit while in the upright and locked position. • Do not let the unit run while in any one stationary position for any period of time. Keep the unit moving while in operation. • Do not allow to be used as a toy. Close attention is necessary when used by or near children. • Use only as described in this manual. Use only manufacturer’s recommended attachments. • Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center or call customer service at: 0845 603 0153. • Do not pull or carry by cord, use cord as a handle, close door on cord, or pull cord around sharp edges or corners. Keep cord away from heated surfaces. • Do not run appliance over cord. • Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. • Do not handle plug or appliance with wet hands. • Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair and anything that may reduce air flow. • Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts. • Do not use to pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes. • Do not use without filter bag assembly in place. • Turn off all controls before unplugging. • Use extra care when cleaning on stairs. • Do not use to pick up flammable or combustible liquids, such as gasoline or lighter fluid, or use in areas where they may be present. • Do not use appliance in an enclosed space where flammable, explosive or toxic vapors are given off by oil base paint, paint thinner, some mothproofing substances, or in an area where flammable dust is present. • Do not pick up toxic material such as chlorine bleach, drain cleaner, gasoline, etc. with this appliance. • Use caution when vacuuming over area rug edges and fringe. . page 2 . page 3 . page 4 . page 5 . page 6 . page 7 . page 8 Important Where Necessary for Plug to be Fitted The wires in this mains lead are coloured in accordance with the following code: Blue: Neutral Brown: Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows; The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black. The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Red. Neither wire is to be connected to the earth pin of the 3 pin plug. SAVE THESE INSTRUCTIONS Replace fuse with same size fuse. Household Use Only 2 Maintenance and Customer Service ACCESSORIES ITEM Your ORECK vacuum cleaner is a product of precise engineering. The motor bearings are permanently lubricated and should not be oiled. If you require additional information or have problems with your ORECK appliance, or to order new bags or spare parts, you may call ORECK customer service at: 1. 0845 603 0153 Or write to: Oreck UK P.O. Box 107 Exeter Devon EX2 8ZQ Attention: Oreck Customer Service Please specify the model number and serial/code number which can be found on the data label on the back of the vacuum. Save your sales or purchase slip. Should your ORECK appliance require warranty service, present this slip to the Authorized Service Center as your proof of purchase date. Warranty ORECK MANUFACTURING COMPANY: (Oreck 1400 Salem Road; Cookeville, TN, USA 38506 gives you the following warranty for this product only if it was originally purchased for residential use, not resale from Oreck or an Oreck Authorized Retail Dealer.) Oreck will repair or replace, free of charge, to the original purchaser, any part that is found to be defective in material or workmanship within two (2) years of date of purchase; ten (10) years on housing. This warranty applies to normal domestic use. Any commercial use of this product will void this warranty. This limited warranty covers the revolving roller brush for one (1) year for residential use only. This warranty does not cover the replacement of expendable or consumable parts such as carbon motor brushes, edge brushes, belts, bulbs, disposable bags and other parts subject to normal wear unless they are defective in material or workmanship. This warranty does not apply to any part subjected to accident, abuse, alteration, misuse, damage caused by act of God, the use of voltages other than indicated on the serial number displayed on this product or service of this product by other than Oreck or a participating Factory Authorized Service Center. Oreck does not authorize any person or representative to assume or grant any other warranty obligation with the sale of this product. Oreck’s warranty is valid only if you retain proof of purchase from Oreck or an Oreck Authorized Retail Dealer for this product. If you purchase this product from any other source, your purchase is “AS IS,” which means Oreck grants you no warranty, and that you, not Oreck, assume the entire risk of the quality and performance of this product, including the entire cost of any necessary servicing or repairs of any defects. This warranty is in addition to your statutory and other legal rights. 3 PART NUMBER Dust Bag, 8 Pack, Saniseal® Hypo-Allergenic CCPK8DW Dust Bag, 8 Pack, Regular CCPK8 2. Belts, 3 Pack 0300604 3. Oreck Fresh Air® Tabs AIRTABS To Replace Paper Filter Dust Bag Assembly To assist you in identifying components of your vacuum, the parts have been numbered as follows: 1 Handle tube, upper 2 Tube, lower 3 Power head 4 Outer bag 5 Paper filter dust bag 5 6 Power cord 7 Retaining spring 8 Bag tension bar 9 Zip fastener 10 On/off switch 11 Cord hook 12 Plastic loop/cable clamp 13 Connector assembly 14 Fan housing 15 Cord assembly 16 Cord Strain Relief Assembly 1 WARNING: Unplug cord from electrical outlet before servicing. 10 11 BAG REMOVAL: 1. Unsnap bag door from base. 9 1 12 2. Gently pull bag from cardboard collar upwards. 16 13 4 2 7 8 6 14 15 3 3. XL2605HH: Dust seal will close automatically 2 TAB BAG INSTALLATION: 1. Slide the cardboard collar completely onto bag dock door. 3 Before assembling appliance, remove two screws from connector assembly. Remove cardboard insert by pulling upward (fig 1). ENFONCEZ JUSQU’À ENTENDRE UN BRUIT PRESIONE HASTA ESCUCHAR UN CHASQUIDO DE SUJECIÓN With ON/OFF switch facing the front of the unit, slide upper handle tube over matching section of the connector assembly. Hold tab of cord strain relief flush with TOP hole in connector assembly. Insert screw through hole in tab of cord strain relief and firmly tighten to connector assembly. Insert remaining screw in bottom hole of connector assembly and tighten firmly (fig 2). NOTE: The power cord comes installed in the cord strain relief. Should the power cord come loose, simply pinch the power cord together and slide approximately 1 - 2 inches through hole in cord strain relief. Carefully slide power cord over clamp on the cord strain relief and pull excess until the power cord is tightly rested under clamp. 2. Firmly push bag dock door with both thumbs on indication point until it snaps. Attach cord to cord clip by pressing cord above and below clip ensuring the cord is fully rested in clip (fig 3). 4 Operating Instructions To Operate Make sure the disposable paper filter dust bag is in place. DO NOT operate the cleaner without a paper filter dust bag. Plug the power cord into an electrical outlet. Press the ON(l) OFF(O) switch on handle assembly when ready to operate. All paper dust bags are not the same. Your ORECK disposable dust bags have been designed to be used with the ORECK cleaner. Using bags other than genuine ORECK TYPE CC disposable bags will affect the cleaning ability of your cleaner and could cause damage to it. General Information The performance of your new cleaner greatly depends upon care and maintenance. The instructions in this manual will guide you in performing basic care and maintenance. To obtain the most satisfying years of service read the instructions and keep them handy for future reference. Antibacterial Technology Oreck added Antibacterial Technology to various touch points, including the handle, outer bag and bag dock while manufacturing this upright vacuum cleaner in order to provide you with antimicrobial protection that continuously fights the growth of microbes that can cause stains, odor and product degradation. When microbes, such as bacteria, mold and mildew come in contact with the product surface, the antibacterial technology penetrates the cell wall and disrupts key functions so they cannon grow or reproduce. Operating Recommendations This new ORECK XL High-Speed Upright is one of the finest, fastest, and strongest units in its class. You’ll love the way it cleans, gets under things, and it’s SO lightweight and easy to use. The Belt The belt on your vacuum cleaner controls the speed of the revolving brush and is very important for the effective operation of the cleaner. If the belt becomes stretched or cut, it will cause the revolving brush to stop completely or slow down. See instructions in the manual for replacing belt. The following are a few simple suggestions regarding its operation: 1. When inserting a new disposable paper filter dust bag— FIRST PUFF OUT and OPEN THE BAG. 2. When the disposable filter dust bag is full, REPLACE IT. 3. If at any time the machine does not pick up properly or makes an unusual noise, STOP OPERATION and service. 4. Although your upright will pick up pins, paper clips, and other small objects, it is recommended that these be removed from the floor before you vacuum. Failure to do so may result in permanent damage to the motor suction fan and its housing. 5. WARNING: Do not use your vacuum cleaner on damp or wet surfaces. This will cause damage to the vacuum cleaner and is dangerous to the user. Damage caused by use on wet or damp surfaces is not covered under warranty. 6. REPLACE THE BELT EVERY 6 MONTHS. 7. Change the disposable filter dust bag at least once a month—even if it is not full! The collected dust in the dust bag can cause odor, attract moisture, act as a breeding area and can affect the efficiency of the cleaner. 8. DO NOT run the vacuum cleaner over cord. The revolving brush could damage the cord. 9. Use caution when vacuuming over area rug edges and fringe. An extra belt is stored in the baseplate of your cleaner. When buying replacement belts, use ONLY ORECK genuine belts. Belts other than ORECK belts will not operate the revolving brush correctly and may create undue stress which will cause damage to the motor and brush bearings. Using belts other than ORECK belts will void the warranty. Lubrication The vacuum cleaner motor bearings are factory lubricated and sealed. Further lubrication is not required. General Cleaner Care At least once a month, check for and remove excessive lint, string or hair from revolving brush. Wipe the outside of the cleaner with a damp cloth. Also clean the connector deflector assembly area, base of cleaner and fan housing area. If there is dust in the outer bag, vacuum it or shake it out. Disposable Paper Filter Dust Bags Disposable paper filter dust bags play a very important role in the efficiency of your ORECK vacuum cleaner. The purpose of the paper bag is to trap dirt, but at the same time it must be porous enough to allow air to pass through. If the paper bag becomes clogged, no air can pass through the cleaner and cleaning cannot take place, regardless of the cleaner’s power. A little preventative maintenance will keep your cleaner looking new and will ensure continued cleaning effectiveness. CAUTION—Wood Floors, Soft (Vinyl, Asphalt Tile, etc.) Floor Surfaces and Polished Floor Finishes Use floor and floor finish manufacturer’s recommended methods of cleaning. The metal strip on the base of the cleaner could be damaged if used on concrete or abrasive surfaces, and, therefore, cause damage to wood floors, soft To keep your cleaner operating at maximum efficiency, change the dust bag frequently. DO NOT FILL ABOVE THE LINE INDICATED ON THE DUST BAG. (vinyl, asphalt tile, etc.) floor surfaces and polished floor finishes. The roller brush may also scuff very soft finishes. Do Be sure the disposable paper filter dust bag is installed properly. not operate the unit while in the upright and locked position. Do not let the unit run while in any one stationary position for any period of time. Keep the unit moving while in operation. 5 How to Replace a Worn Belt To Adjust or Replace Brush WARNING: Unplug cord from electrical outlet before servicing. WARNING: Unplug cord from electrical outlet before servicing. Remove the replacement belt from the storage channel. To determine if the brush is worn, place a firm straight edge across the nozzle opening. If brush bristles do not extend beyond baseplate, brush should be adjusted. Remove the door by removing the hold down screw located on side of power head. Remove the baseplate by removing 5 screws. Then, remove the belt and brush roll from the housing. Slide the door forward by prying open with a screwdriver or coin. Rotate both bearing assemblies at ends of brush roll to show “OLD” and replace in the holding channels in the housing. Remove the belt from the brush roll pulley and the motor drive shaft. Rotate and match bearing assemblies Loop the new belt over the motor drive shaft. Place the opposite end of the belt on the brush roll pulley. NOTE: The bearing assembly setting marked “OLD” has a smooth side. The one marked “NEW” has notches. When rotating bearings, make sure both bearing assembly settings are the same and face up when replacing the brush roll. Reassemble the belt and the baseplate and check bristle height above baseplate at each end of brush. Rotate the brush roll three (3) complete revolutions to ensure that no part of the belt is overhanging the end of the motor drive shaft. IMPORTANT: Unless the brush is worn as indicated above, both bearings must be in the “NEW” position. When rotating, both bearings must be in the “OLD” position. Unmatched settings will cause damage to your machine. Replace the door by sliding it into the groove at the bottom of the housing. Replace the hold down screw. 6 If a previous adjustment has already been made and bristle height does not extend above baseplate, a new brush assembly should be ordered. 5. Many times blockage occurs due to a full dust bag causing dirt to back down the air flow system. When that happens, the blockage will be at the top of the system, starting in the area where the dust bag connects to the connector assembly. See illustration F. Stuffing or Blockage Under certain conditions it is possible to stuff or block the intake tube and the lower tube assembly. If your vacuum cleaner does not pick up properly, or makes unusual noise and the outer bag does not fluff up or balloon open, follow the following steps: ± WARNING: Unplug cord from electrical outlet before servicing. A Intake Opening B Intake Opening Retainer Spring C Fan Housing O-ring D E 1. Check for blockage at the mouth of the intake opening. See illustration A. If there is blockage, remove it with long-nose pliers, a screwdriver or coat hanger. If you can not reach the blockage, remove baseplate. See illustration B. 2. If the blockage is not at the base, remove lower tube. See illustration C. Unhook retainer spring, releasing bottom of bag. Twist lower collar counterclockwise to slide up. Pull tube out of base. Check for blockage. If blockage is in the tube, remove with a coat hanger. 3. If tube is not blocked, look into fan housing. See illustration D. Remove debris with long-nose pliers, a screwdriver or coat hanger. 4. To reassemble, check O-ring on tube, and replace if damaged. Vacuum will not operate properly without the tube O-ring. Slide O-ring to approximately 2" from base of tube. Replace tube by first lining up slot at base of tube with inner tab inside fan housing. Then reinsert tube and push down until the tube is seated. Make sure O-ring is in place against fan housing opening. Replace and tighten collar until collar locking tabs are locked in place. See illustration E. Make sure collar is not cross threaded on housing. F Connector Deflector Opening NOTE: If the “Stuffing or Blockage” actions do not correct the problem, contact an ORECK authorized service center or call the customer service center at: 0845 603 0153. IMPORTANT: On plush and new carpets, stuffing may occur due to excessive fuzz and loose cuttings in the carpet. Stuffing could occur for the first few cleanings until all the loose material is removed. Due to the high efficiency of the cleaner, many older carpets will cause stuffing when the cleaner is first used on them. Using An Oreck Fresh Air Tab ® Your ORECK XL vacuum cleaner has a special Oreck Fresh Air® tab pocket. This pocket is located inside the outer bag in the area where the disposable paper bag attaches to the intake tube. Insert tablet in pocket. 7 Troubleshooting Guide WARNING: Unplug cord from electrical outlet before servicing. SAVE SERVICE CALLS...CHECK THESE FIRST: • Is the disposable filter dust bag full? • Are pores of filter dust bag clogged with powder or fine dust? • Is anything clogging the revolving brush, lower tube, intake opening, fan housing or connector assembly opening? • Is the belt in place and turning the brush? • Are the brush ends in the proper location? • Does the brush turn freely? Are hair, string or rug fibers wound around the brush? PROBLEM CLEANER WILL NOT RUN CLEANER DOES NOT PICK UP POSSIBLE SOURCE AREAS TO CHECK Not plugged in properly. Be sure cleaner is firmly plugged into wall outlet. No electricity in wall outlet. Check electrical source–fuse or circuit breaker. Filter bag is full. Replace filter bag. See “To Replace Paper Filter Dust Bag.” Nozzle or intake pivot clogged. Clear obstruction. Belt is broken or stretched. Replace belt. Brush is worn. See “To Adjust or Replace Brush.” Bag tube clogged. Clear obstruction. Bag pores are clogged with fine dust. Change bag. Impeller fan is broken. Return to Service Center for repair. Revolving brush is not even at both ends. Check brush roll end cards. Make sure words “OLD” or “NEW” match at each end. ALL OTHER SERVICING SHOULD BE DONE BY AN ORECK AUTHORIZED SERVICE CENTER. CALL CUSTOMER SERVICE HOT LINE 0845 603 0153 Whenever calling, please be sure to have your model and serial number from data plate. ©2009 Oreck Holdings, LLC. All rights reserved. All word marks, logos, product configurations, and registered trademarks are owned and used under the authority of Oreck Holdings, LLC. Printed in America. 75812-01 REV A 8 01/09 ECN# R-9282
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Create Date : 2009:07:21 11:33:14-05:00 Modify Date : 2009:07:21 11:33:14-05:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Producer : Acrobat Distiller 9.0.0 (Windows) Format : application/pdf Title : untitled Document ID : uuid:2d197340-1fd9-46c0-a00d-e51c335a2c94 Instance ID : uuid:72d352dc-bde8-49fc-8e16-ac2af7ad0e32 Page Count : 8EXIF Metadata provided by EXIF.tools