Oregon Scientific Starck Ps M02 Users Manual English R18 Op
PS-M02 to the manual 4964582d-78c1-4b20-9d0d-71a677ffe645
2015-02-04
: Oregon-Scientific Oregon-Scientific-Starck-Ps-M02-Users-Manual-374487 oregon-scientific-starck-ps-m02-users-manual-374487 oregon-scientific pdf
Open the PDF directly: View PDF 
.
Page Count: 27
| Download | |
| Open PDF In Browser | View PDF |
EN Full Weather Station with Radio Controlled Clock and Projection (Model #: PS-M02 / PS-M02U) User Manual PS M02 English Cover R7 op 1 Black 7/24/03, 11:57 AM EN TABLE OF CONTENTS About this guide ........................................................ 2 Product overview ....................................................... 3 Getting started .......................................................... 8 Batteries .............................................................. 8 AC power adapter ............................................... 8 Switch between modes ....................................... 8 Change settings .................................................. 9 Remote unit setup ...................................................... 9 Clock ...................................................................... 10 Alarm ...................................................................... 11 Calendar ................................................................. 12 Moon phase ............................................................ 12 Barometer ............................................................... 13 Weather forecast ..................................................... 14 Temperature & humidity ........................................... 14 Backlight ................................................................. 17 Projector ................................................................. Reset system ........................................................... Safety and care ....................................................... Warnings ................................................................. Troubleshooting ....................................................... Specifications .......................................................... Additional resources ................................................ 1 PS M02 English R18 op 1 Black 7/24/03, 11:56 AM 18 19 20 20 21 22 25 EN In this box, you will find: ABOUT THIS GUIDE Congratulations on your selection of the Philippe Starck with Oregon Scientific Full Weather Station with Radio Controlled Clock and Projection (PS-M02 / PS-M02U). This powerful device bundles time keeping, alarm, indoor and wireless outdoor temperature and humidity monitoring, weather forecasting, and projection features into a single tool you can use from the convenience of your home. • • • • Main unit Remote sensor Batteries AC/DC power adapter Keep this manual handy as you use your new product. It contains practical step-by-step instructions, as well as technical specifications and warnings you should know. 2 PS M02 English R18 op 2 Black 7/24/03, 11:56 AM EN PRODUCT OVERVIEW DESCRIPTIONS TOP VIEW 1. 2. 3. Snooze / Light button Light sensor Projection lens 1 3 2 3 PS M02 English R18 op 3 Black 7/24/03, 11:56 AM EN LCD DISPLAY DESCRIPTIONS 1. 2. 3. 4. 5. 6. 7. 8. 1 2 3 7 Low battery icon Clock Barometer Weather forecast Moon phase Calendar Temperature and humidity Alarm 4 8 5 6 4 PS M02 English R18 op 4 Black 7/24/03, 11:56 AM EN BACK VIEW BUTTON DESCRIPTIONS 1 1. 2. 3. 4. 5. 6. 7. 2 3 4 Select - switch modes / change settings Focus - focus projector Up - increase setting / activate auto-synch Down - decrease setting / deactivate auto-synch Rotation - rotate projector Alarm -activate / deactivate alarm Channel - switch remote unit 5 6 7 5 PS M02 English R18 op 5 Black 7/24/03, 11:56 AM EN DESCRIPTIONS BOTTOM AND SIDE VIEW 1. 2. 3. 4. 5. 2 1 Battery compartment Backlight switch Reset button Light sensitivity knob DC power input jack NOTE AC power adapter not shown. 3 4 5 6 PS M02 English R18 op 6 Black 7/24/03, 11:56 AM EN DESCRIPTIONS REMOTE UNIT 1 1. 2. 3. 4. 5. 6. 7. 8. 9. 4 2 5 6 7 3 Temperature / Trend display Low battery icon Humidity / Trend / Comfort Level display °C/°F switch Channel switch Reset button Battery compartment Wall-mount hole Battery compartment lid 8 9 7 PS M02 English R18 op 7 Black 7/24/03, 11:56 AM EN GETTING STARTED NOTE Insert the batteries in the remote unit before you set up the main unit. Do not use rechargeable batteries. BATTERIES Batteries for the remote and main units are supplied with this product. Replace them whenever the low battery signal ( ) displays. Remove the battery compartment lid on the bottom of the main unit, and insert the batteries. You will need a small Phillips screwdriver to remove the remote unit compartment lid. Be sure to match the correct polarity, as shown in the battery compartment. Before you close the lid, press the RESET button with the point of a blunt object (such as a ball point pen). AC POWER ADAPTER An AC power adapter is supplied for use with the main unit. You must connect the power adapter if you wish to use the continuous projection or backlight features. The jack is located on the side of the unit. NOTE If the AC power becomes unavailable, the unit will automatically switch to battery power. SWITCH BETWEEN MODES Press SELECT. The selected mode will flash. The display will stop flashing if no key is pressed within 5 seconds. 8 PS M02 English R18 op 8 Black 7/24/03, 11:56 AM EN CHANGE SETTINGS Press and hold SELECT for 2 seconds. Then, press UP or DOWN to change each setting. Press SELECT to switch options. INSTALLATION Mount the remote unit on a flat surface using the recess holes on the back of the unit. For best results: • Before you insert the batteries, select the measurement unit and channel number first. • Place the unit out of direct sunlight and moisture. • Do not place the remote unit more than 20 - 30 meters (60 - 90 feet) from the main (indoor) unit. • Position the unit so that it faces the main (indoor) unit. Minimize obstructions such as doors, walls, and furniture. REMOTE UNIT SET UP Up to 3 remote units can be used with this product to monitor outdoor temperature and humidity. The measurement unit (°C or °F) and channel number (1, 2, or 3) switches are located in the battery compartment, and should be set prior to installation. NOTE Additional remote units sold separately. If you are using more than one remote unit, be sure to select a different channel number for each unit. You may need to experiment with various locations to get the best reception. 9 PS M02 English R18 op 9 Black 7/24/03, 11:56 AM EN NOTE For best results, place the unit away from metal or electrical objects, and near a window with a clear view to the sky. CLOCK This product can automatically synchronize the date and time with official time-keeping organizations in Frankfurt, Germany (PS-M02) or Rugby, England (PS-M02U). When the unit is within 1500 km (932 miles) of a RF signal, the reception icon will blink during reception. TO DISABLE OR ENABLE AUTOSYNCHRONIZATION In Clock mode, press DOWN for 2 seconds to disable the auto-synchronization. The unit will not respond to radio signals until you reactivate the synchronization. RECEPTION Reception takes 2 - 10 minutes to complete. Once complete, the icon will stop blinking. Strong signal Weak signal To enable auto-reception, press UP for 2 seconds. No signal 10 PS M02 English R18 op 10 Black 7/24/03, 11:56 AM EN SET ALARM 1. Press SELECT several times until the Alarm area flashes. 2. Press and hold SELECT for 2 seconds to enter the setting mode. 3. Select the hour, minute, melody (1 - 7) and volume level (Lo or Hi). Press UP or DOWN to change the setting. Press SELECT to confirm. 4. Press SELECT again when you are finished. SET OR CHANGE THE CLOCK 1. Press SELECT to switch to the Clock Mode. The time will flash. 2. Press and hold SELECT for 2 seconds to enter the setting mode. 3. Select the 12/24-hour format, hour, and minute. Press UP or DOWN to change the setting. Press SELECT to confirm. ALARM When activated, the Melody Alarm starts quietly, then gradually becomes louder. It shuts off after two minutes. The LCD display lights up for the first 8 seconds. SNOOZE Press the SNOOZE/LIGHT button the top of the unit to temporarily disable the alarm for 8 minutes. The alarm icon will blink while Snooze is activated. 11 PS M02 English R18 op 11 Black 7/24/03, 11:56 AM EN 3. TO TURN THE ALARM OFF OR ON Press any button to stop the alarm. To turn the alarm off completely (deactivate it for the next day), press ALARM. Select the year, month, date, and language. Press UP or DOWN to change the setting. Press SELECT to confirm. NOTE The language options are (E) English, (F) French, (D) German, (I) Italian, and (S) Spanish. CALENDAR MOON PHASE Press SELECT until the Calendar Area flashes. Then, press UP or DOWN to change the date and view the corresponding moon phase. SET DATE Clock auto-synchronization must be deactivated before you manually set the date. ( 10) 1. 2. Press SELECT several times until the calendar area flashes. Press and hold SELECT for 2 seconds to enter the calendar setting mode. 12 PS M02 English R18 op 12 Black 7/24/03, 11:56 AM EN BAROMETER This product tracks barometric pressure changes over the past 24 hours to provide the weather forecast ( 14) and a trend line showing the direction of barometric change. Barometric changes are measured by the main (indoor) unit. Trend BAROMETRIC TREND The barometric trend arrow for the last 30 minutes is always displayed. Description Pressure change (mb/hPa) 1 hr 6 hrs Rising +1 +3 Steady Steady Steady Falling -1 -3 VIEW THE LAST 24 HOURS Press SELECT 2 times until the Barometer Area flashes. Then, press UP or DOWN to view the last 24 hours history. 13 PS M02 English R18 op 13 Black 7/24/03, 11:56 AM EN SET UNIT AND ALTITUDE You can set the unit of measurement (mb/hPa or inHg) and altitude. Setting the altitude allows the product to take more accurate barometric measurements. 1. 2. 3. WEATHER FORECAST This product forecasts the next 12 to 24 hours of weather within a 30 to 50 km (19 - 31 mile) radius with 70 to 75 percent accuracy. The weather forecast is always displayed. Press SELECT 2 times until the Barometer Area flashes. Press and hold SELECT for 2 seconds. Select altitude (-100 meters to 2500 meters in increments of 10) and the unit of measurement (mb/hPa or inHg). Press UP or DOWN to change the setting. Press SELECT to confirm. Clear Partly Cloudy Cloudy TEMPERATURE AND HUMIDITY With the press of a button, you can check the current indoor or outdoor temperature, humidity percentage, comfort level, trend, and record measurements. Outdoor measurements are collected by the remote unit. 14 PS M02 English R18 op 14 Black Rainy 7/24/03, 11:56 AM EN Temperature is given at the top; humidity is below. and hold CHANNEL for 2 seconds to enter Auto scan mode. If only 1 remote unit is in use, you will not be able to change channels or select Auto. If you select “Auto”, the channel will change every 3 seconds. To deactivate, press and hold CHANNEL for 2 seconds again. VIEW MIN / MAX / CURRENT MEASUREMENTS Press SELECT 3 times until the Temperature and Humidity Areas flash. Press UP or DOWN to scan the readings. SENSOR SEARCHING If there is no remote unit signal, the temperature and humidity measurements will be blank. Check the remote unit batteries, or press and hold UP and DOWN for 2 seconds to search for the remote unit(s). CLEAR MIN / MAX RECORDS While viewing Min/Max records, press and hold UP or DOWN for 2 seconds until a beep sounds. This clears the previous measurements from the memory. Searching No sensor SELECT REMOTE UNIT CHANNEL While in the Temperature / Humidity Mode, press CHANNEL to switch between CH 1, 2, or 3, or press 15 PS M02 English R18 op 15 Black 7/24/03, 11:56 AM Sensor found EN COMFORT ZONE The indoor and outdoor comfort zones are shown for the following conditions. NOTE Signals from household electrical appliances such as doorbells and home security systems can cause temporary reception failures between the indoor and outdoor units. This is normal and does not affect the general performance of the product. Reception will automatically resume once the interference ends. Zone Temperature RelativeHumidity Any >70% Any <40% 20 - 25 °C (68 - 77 °F) 40 - 70% Wet Dry Comfort 16 PS M02 English R18 op 16 Black 7/24/03, 11:56 AM EN SET UNIT While in Temperature / Humidity Mode, press SELECT for 2 seconds. Press UP or DOWN to switch between °C and °F. Press SELECT to confirm. TRENDS The trend arrow for the last 30 minutes always displays. Indoor and outdoor temperature and humidity trends are shown separately. Trend Temperature Relative Humidity +0.5 °C +3% Steady Steady -0.5 °C -3% BACKLIGHT Press SNOOZE/LIGHT to illuminate the backlight for 5 seconds. CONTINUOUS BACKLIGHT The AC power adapter must be plugged in to use this feature ( 8). 1. The BACKLIGHT switch is located in the battery compartment. Move it to the “ON” position to enable the continuous backlight. Move it to the “OFF” position to disable. 17 PS M02 English R18 op 17 Black 7/24/03, 11:56 AM EN 2. 3. Move it to the “AUTO” position to enable continuous backlight controlled by light intensity. When activated, the backlight will be on whenever the unit perceives that the room is dark. The Light Sensitivity knob switch is located in the battery compartment. Rotate to adjust. PROJECTOR This product has a built-in projector for viewing time and alarm status at night. NOTE The maximum projection range is 2 meters (6 feet). The image gets larger the farther you display it. PROJECT TIME / ALARM STATUS In a darkened room, press SNOOZE/LIGHT to display the time and alarm status for 5 seconds. E OI LIGHT SENSOR FLIP IMAGE Press SNOOZE/LIGHT again while the projector is on. LIGHT ON OFF AUTO RESET 4. ROTATE IMAGE The ROTATION switch is located on the back of the unit. Rotate to adjust. When activated, the continuous backlight will be half as bright as usual. To achieve full brightness, press SNOOZE/LIGHT. 18 PS M02 English R18 op 18 Black 7/24/03, 11:56 AM EN FOCUS IMAGE The FOCUS switch is located on the back of the unit. Rotate to adjust. RESET SYSTEM The RESET buttons are located in the battery compartments for the main and remote units. Press these buttons with the tip of a blunt object (such as a ball point pen) whenever you change the batteries, or whenever performance is not behaving as expected (e.g., unable to establish radio frequency link with remote unit or automatic clock, etc.) This will return all settings to default value, and you will lose all stored information (minimum / maximum temperature and humidity, etc.). CONTINUOUS PROJECTION The AC power adapter must be plugged in to use this feature ( 8), Press and hold SNOOZE/LIGHT for 2 seconds when the projection is on. When activated, the time and alarm status will project continuously. Press and hold SNOOZE/LIGHT for 2 seconds again to deactivate. 19 PS M02 English R18 op 19 Black 7/24/03, 11:56 AM EN • SAFETY AND CARE Wash the unit with a slightly damp cloth and mild detergent. Avoid dropping the unit or placing it in a location where the AC power adapter will be stepped on. • • • WARNINGS This product is designed to give you years of service if handled properly. Observe the following guidelines: • • • • • Never immerse the unit in water. This can cause electrical shock and damage the unit. Do not subject the main unit to extreme force, shock, or fluctuations in temperature or humidity. Do not tamper with the internal components. Do not mix new and old batteries or batteries of different types. • Do not use rechargeable batteries with this product. Remove the batteries if storing this product for a long period of time. Do not scratch the LCD display. Do not make any changes or modifications to this product. Unauthorized changes may void your right to use the product. The contents of this user manual are subject to change without notice. Images not drawn to scale. 20 PS M02 English R18 op 20 Black 7/24/03, 11:56 AM EN TROUBLESHOOTING Check here before contacting our customer service department. Problem Temp Calendar Backlight Projector Symptom Shows “LLL” or “HHH” Strange date / month Remedy Temperature is outof-range. No continuous backlight Plug in AC power adapter. Check the BACKLIGHT switch. ( 8, 17) Plug in AC power adapter ( 8, 18, 19) No continuous projection Problem Remote unit Symptom Cannot locate remote unit Check location ( 9) Cannot change channel Change language ( 12) Clock Cannot autosynchronize 21 Black Check sensors. Only one sensor is working ( 15 ) 1. Remove batteries. 2. Press RESET. All memory items will return to default. 3. Replace batteries. 21 PS M02 English R18 op Remedy Check batteries ( 8) 7/24/03, 11:56 AM EN Problem Baro Symptom Remedy 4. Place clock near window / away from electrical devices, and wait 10 - 20 minutes. SPECIFICATIONS If it still fails, you may be too far from a signal. Remote unit dimensions LxWxH 75 x 35 x 78.3 mm (3 x 1.4 x 3.1 inches) Weight 136 grams with battery Cannot change clock Disable autosynchronization ( 10) Strange reading Set altitude / unit ( 14) Main unit dimensions LxWxH 129 x 43 x 133.3 mm (5.1 x 1.7 x 5.3 inches) Weight 471 grams with batteries Temperature Unit Range °C or °F Main unit: -5 ºC to 50 ºC (23 ºF to 122 ºF) 22 PS M02 English R18 op 22 Black 7/24/03, 11:56 AM EN Resolution Comfort Memory Trend Remote Unit: -20 °C to 60 °C (-4 °F to 140 °F) 0.1 °C (0.2 °F) 20 °C to 25 °C (68 °F to 77 °F) (see also, Relative humidity) Minimum / maximum +/- 0.5 °C (+/- 0.9 °F) change Range Resolution Altitude Display Memory Trend Relative humidity Range Main & Remote Unit 25% to 95% Resolution 1% Comfort 40% to 70% (see also, Temperature) Memory Minimum / maximum Trend 3% change Barometer Unit Remote unit RF frequency Range Transmission Channel No. Unit mb/hPa or inHg 500 to 1050 mb (14.77 to 31.01 inHg) 1 mb (0.03 inHg) -100 to 2500 meters (-328 to 8202 feet) Rainy, cloudy, partly cloudy, sunny 24 hour 1mb change in 1 hour or 3mb change in 6 hours 433 MHz 30 meters (98 feet) with no obstructions approximately every 40 seconds 1, 2, or 3 °C or °F 23 PS M02 English R18 op 23 Black 7/24/03, 11:56 AM EN Power Main unit Radio-controlled clock Synchronization Auto or disabled Clock display HH:MM:SS Hour format 12hr AM/PM (MSF format) 24hr (DCF format) Calendar DD/MMM; weekday selection in 5 languages (E, D, F, I, S) Moon phase High, medium, and low tide Alarm 7 melody; 2 minute crescendo Snooze 8 minutes Projector Display Rotation Focusing Projection Remote unit 4 x UM-3 (AA) 1.5V alkaline batteries (back-up) AC/DC 6V power adapter (for normal operation and continuous backlight and projector) 2 x UM-4 (AAA) 1.5V alkaline batteries Current time / alarm status 180° and image flip Manual 5-second or continuous 24 PS M02 English R18 op 24 Black 7/24/03, 11:56 AM EN ADDITIONAL RESOURCES Visit our website (www.oregonscientific.com) to learn more about your new product and other Oregon Scientific products such as digital cameras, hand-held organizers, health and fitness gear, and weather stations. The website also includes contact information for our customer service department, in case you need to reach us. 25 PS M02 English R18 op 25 Black 7/24/03, 11:56 AM EN Additional information: The product is therefore conform with the Low Voltage Directive 73/23/EC, the EMC Directive 89/336/EC and R&TTE Directive 1999/5/EC (appendix II) and carries the respective CE marking. EC-DECLARATION OF CONFORMITY This product contains the approved transmitter module TX 07 and complies with the essential requirements of Article 3 of the R&TTE 1999/5/EC Directives, if used for its intended use and that the following standard(s) has/have been applied: VS-Villingen / Germany August 2003 Gerhard Preis R&TTE Representative of manufacturer Radio frequency spectrum (Article 3.2 of the R&TTE Directive) applied standard(s) ETSI EN 300 220-3 (Ver.1.1.1):2000-09 Electromagnetic compatibility (Article 3.1.b of the R&TTE Directive) applied standard(s) ETSI EN 301 489-1-3 (Ver.1.4.1):2002-08 RTT&E Compliant Countries: All EC Countries, Switzerland CH , and Norway N Safety of information technology equipment (Article 3.1.a of the R&TTE directive) applied standard(s) EN 60950:2000 ©2003 Oregon Scientific. All rights reserved. 26 PS M02 English R18 op 26 Black 7/24/03, 11:57 AM
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2003:07:24 18:58:01Z Modify Date : 2003:07:24 11:59:27-07:00 Page Count : 27 Creation Date : 2003:07:24 18:58:01Z Mod Date : 2003:07:24 11:59:27-07:00 Producer : Acrobat Distiller 5.0.2 for Macintosh Author : G4/2 Metadata Date : 2003:07:24 11:59:27-07:00 Creator : G4/2 Title : PS M02 English R18 opEXIF Metadata provided by EXIF.tools