Osram Sylvania LEDEXT-10X Small RGB LED ambient lighting device used as an automotive accessory. User Manual Manual
OSRAM SYLVANIA Inc. Small RGB LED ambient lighting device used as an automotive accessory. Manual
Manual
PLEASE NOTE BEFORE YOU BEGIN:
DO NOT ATTEMPT TO PAIR
THROUGH PHONE SETTINGS;
CONNECT THROUGH APP.
ZEVO® PULSE LIGHT ENGINE
INSTALLATION GUIDE
Q19141643
• Keep components out of reach of small children.
• To avoid possible fire, product damage, or early product failure, do not
position components in areas exposed to high heat.
• Changes or modifications to this unit not expressly approved by the
party responsible for compliance, could void the users’ authority to
operate the equipment. Consult state andlocal regulations regarding
the use of accent color lightingon your vehicle.
• Do not install this product if it interferes with vehicle control or safety
features such as air bags, steering wheel, brakes, clutch or gas pedals
• This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Your new ZEVO® Pulse system uses LED Light Engines to dynamically
project colored light to your vehicle’s headlight refalectors.
Carefully unpack your ZEVO® Pulse system. Lay all components out
individually. Read all instructions completely prior to installation.
WARNING
There are many different headlight reflector designs. You will need to
determine the best location to attach your ZEVO® Pulse Light. Placing
the light engine along the lower edge of the headlight reflector is often
best – the choice is up to you. Place a piece of masking tape on each
lens to identify your chosen mounting positions. You will not be
mounting the light engines until the controller is first mounted and the
wires are routed.
2Finding the best location
If your package has a “Try-Me,” separate the spade connectors from
the red & black wires.
The “Try Me” harness may be discarded.
Disconnect the “Try-Me” wire harness
3
Wire Harness
“Try-Me”
The power supply wires are 39 inches long. The light engine wires are
78 inches long. Select a mounting location for the ZEVO® Pulse
controller within the engine compartment so the wires can reach the
12V source and the headlight lenses. It is critical to keep the controller
and the wires away from hot surfaces. Ensure the selected controller
mounting location allows for the wires to be neatly routed and secured
along the way. Use the provided wire ties to secure the ZEVO® Pulse
controller. Connect the power supply wires–the black wire to battery
(-) and the red wire to a suitable +12V circuit.
Installing and mounting the controller box
4
Take each light engine cable and secure the wires along the route to
the headlight. Take the provided alcohol wipe and clean the light
engine mounting surface on the LED side as well as the headlight lens
location where the light engine is to be attached. Take care to properly
clean these surfaces, as any residual contaminant from handling the
light engine or anything on the headlight lens mounting location will
result in poor adhesion.
Clean the light engine
surface on the “LED side”
LED Light Engine
Mounting the light engines5
Peel off the release film from one side of the
double-sided mounting tape for the Light engine.
Release Film
Mounting tape has release film on both sides6
Attach double sided mounting tape to each ZEVO® light engine on the
LED side. Be sure to align the tape opening with the LED side opening
on the light engine.
7
INSTALLING THE
APPLICATION
FREQUENTLY
ASKED
QUESTIONS
10
Upon opening, the app gives
you a WARNING screen. Read
the warning and then touch the
“I AGREE” button to continue.
11 12 13
Touch the colored display to
select a color. The lower bar
controls the brightness.
Slide it left for brighter, or to
the right for dimmer.
17 18
14
Use the “Color” tab, located
at the lower left corner, to
manually select a light color.
16
Select “Library” to open the
music files on your Bluetooth®
device. The Pulse colors will
dynamically respond to your
music selections.
Select “Microphone” to
enable your Pulse to respond
to the microphone in your
Bluetooth® device.
2019 Q: Do I need a switch to turn off the power to the ZEVO® Pulse controller?
A: You do not need to shut off the controller as it uses only 5mA in sleep mode.
Q: My Bluetooth® device cannot find my ZEVO® Pulse controller. What do I do?
A: Remove the fuse for a moment and replace it. Then swipe down to refresh device list.
Q: If my Bluetooth® device is shut off or moves far away from the vehicle, what happens?
A: Your ZEVO® Pulse will continue to operate for about 30 minutes and then shut off.
Q: Can anyone else change my ZEVO® Pulse settings from their Bluetooth® device?
A: Your ZEVO® Pulse Controller is not accessible to others while your Bluetooth® device is connected.
If your Bluetooth® device is out of range or off, another Bluetooth® device with the proper app can
communicate with your ZEVO® Pulse controller.
Remove the remaining film from the mounting tape.
8
Attach the ZEVO® Pulse light engine at the previously cleaned,
headlight lens position. Press and hold the light engine to the
headlight lens for about 15 seconds, to allow the adhesive to set.
9
Touch “Done” when you have
finished editing the name.
15
Download the SYLVANIA ZEVO®
app from Google Play™ or the
App Store®
. Once it is loaded on
your device, open the ZEVO® app.
Google Play is a trademark of Google Inc.
App Store is a registered Trademark of Apple. Inc
The app can control multiple
ZEVO® Hybrid and ZEVO® Pulse
controllers. Here we show 4
connected systems. To set them
all to the same mode, leave the
“active” checked. To set them to
different modes or colors, deselect
the systems you wish not to
change, then change the settings
of the selected system.
Use the “Audio” tab, located at
the lower center, to have your
ZEVO® Pulse react to the beat
of your music.
Make sure your hand held device has
the Bluetooth® function turned on.
Swipe down from the center of the
screen for your hand held device to
search for your ZEVO® Pulse controller.
If your ZEVO® Pulse is not found after a
few swipes, make sure you are close
enough to it. If you are close enough,
then cycle power to the controller and
swipe the screen to refresh again.
Note: Do NOT use the phone’s
Bluetooth® setting menu to connect to
the ZEVO® Pulse.
Once your handheld device
locates your ZEVO® Pulse, it will
change from “searching” to
“connected”. A checked
“active” indicates you can
change Color or Audio settings. A
default name (shown here as
“ZEVO”) will be assigned.
Touching the default name
(shown here as “ZEVO”) allows
you to change it.
Introduction
1