Oticon A S FU2CICWL Hearing Aid User Manual COMPANY LETTER HEAD

Oticon A/S Hearing Aid COMPANY LETTER HEAD

InstallationInstructions.pdf

                                                                   PEOPLE FIRST   Oticon A/S      Kongebakken 9      DK-2765 Smørum      www.oticon.com   Main +45 39 17 71 00    Fax +45 39 27 79 00    Denmark        CVR-no. 42334219      1  Oticon Radio Model - Quick Installation Guide  Radio Model Name:  CIC WL Fusion 2  The CIC WL Fusion 2 radio model is a low power, short range, inductive radio transceiver working at 3.84 MHz. It can be seen below:                    CIC WL Fusion 2 – Typical Radio Model Assembly  The most important parts of the module are an amplifier (containing a Digital-Signal-Processor (DSP), a radio Front-End (FE), memory and smaller components),  a battery and a coil antenna, all mounted on a plastic faceplate. The microphone is also mounted on the faceplate and externally to it there is normally also an audio receiver/speaker and some optional push buttons, but they are not part of the radio model. The radio model is intended to be installed in Oticon and affiliated wireless hearing aid devices of CIC WL (Completely-In-the Canal) and IIC WL (Invisible-In-the Canal) wearing styles.
                                                                   PEOPLE FIRST   Oticon A/S      Kongebakken 9      DK-2765 Smørum      www.oticon.com   Main +45 39 17 71 00    Fax +45 39 27 79 00    Denmark        CVR-no. 42334219      2  Oticon Radio Model - Quick Installation Guide  Radio Model Name:  CIC WL Fusion 2  The DSP, FE, memory and smaller components in the amplifier are all mounted on a flexible Printed-Circuit-Board (PCB), which is connected to the antenna through  two  short  wires.  The  DSP  is  the  main  processor  controlling  the  amplifiers  functionality  and  the  FE  is  a  complete  radio  transceiver,  including  both transmitter,  receiver  and  local  oscillators.  The  module  also  includes  all  voltage  regulators  inside  the  DSP  and  FE  and  buffered  data programming  inputs (PC_DATA and PC_CLOCK) on board.   CIC WL Fusion 2 – Amplifier Assembly in 2D  The module only requires a battery, an external microphone and speaker to be attached in order to run. All components are kept in place by the face plate as mechanical carrier for the radio model.
                                                                   PEOPLE FIRST   Oticon A/S      Kongebakken 9      DK-2765 Smørum      www.oticon.com   Main +45 39 17 71 00    Fax +45 39 27 79 00    Denmark        CVR-no. 42334219      3   Oticon Radio Model - Regulatory Label Information    Radio Model Name:  CIC WL Fusion 2   Contains:  FCC ID:  U28FU2CICWL      IC:    1350B-FU2CICWL   NOTICE: This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.  Operation is subject to the following two conditions: (1)   This device may not cause harmful interference, and (2)   This device must accept any interference received, including   interference that may cause undesired operation.  Changes or modifications made to this equipment not expressly approved by Oticon A/S may void the FCC authorization to operate this equipment.    Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.  L'exploitation est autorisée aux deux conditions suivantes: (1)  l'appareil ne doit pas produire de brouillage, et  (2)  l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Navigation menu