Otto Bock HealthCare MUG6081 Serial Cable Replacement User Manual UserMan
Otto Bock Healthcare Products GmbH Serial Cable Replacement UserMan
UserMan
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 618463 |
| Application ID | qdFVq9Pm9dYquGRWB+3gpg== |
| Document Description | UserMan |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 74.42kB (930282 bits) |
| Date Submitted | 2006-01-11 00:00:00 |
| Date Available | 2006-01-10 00:00:00 |
| Creation Date | 2005-11-04 07:21:17 |
| Producing Software | Adobe PDF Library 5.0 |
| Document Lastmod | 2006-01-11 12:59:09 |
| Document Title | UserMan |
| Document Creator | Adobe InDesign 2.0.1 |
The EUT is labled with its own FCC ID number. If the module is inside of an end product, the label will not be visible. GB Printed in Austria - 11.05 BionicLinkModule 1 The EUT is labled with its own FCC ID number. If the module is inside of an end product, the label will not be visible. Attention: To be installed by trained staff only. 1 Intended Use The BionicLinkModule is used for a cordless configuration and diagnosis of other Otto Bock products. Its main purpose is the replacement of the currently used serial cables. It has a three wire serial interface. 2 Description and Function It uses Bluetooth® technology, because this technology allows an easy connection to a PC, a PDA or to a similar device. These devices either must have the Bluetooth® functionality incorporated or use an external Bluetooth® interface such as a USB dongle or a Compact Flash- or PC-Card. The BionicLinkModule is conceived as a modular device, which can be permanently built into other products of Otto Bock. Special Features of the BionicLinkModule are: • The module is very flat. • Onboard PCB antenna, to achieve a higher antenna efficiency compared to the wide spread ceramic antennas. The goal is to maximize the connection range without increasing the output power of the RF components. This avoids unnecessary spurious emissions and minimizes the power drain out of the battery of the prosthetic device. • One single LED indicator shows the user if the module is powered (LED is on) and if data is transmitted (LED flashing). 3 Technical Data Temperature Range: Supply Voltage Range: Bluetooth Class II 0° - 60°C 3.5 – 4.7V 4 Mounting Restrictions: • The module has to be mounted in a way to insure that the human tissue is held at a minimum distance as shown in figure (2) and (3). • The module has to be placed isolated from metal surfaces at a minimum distance of 1mm, as shown in figure (1). • It is forbidden to make any modifications, especially of the antenna. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Modifications not expressly approved by Otto Bock could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This product has a modular FCC approval according to FCC public notice DA 00-1407 (released: June 26th, 2000) The EUT is labled with its own FCC ID number. If the module is inside of an end product, the label will not be visible. In this case the end product will be labled exterior with the following information: "This device contains FCC ID: SJ3MUG6081" End users may not be provided with the module installation instructions. OEM integrators and end-users must be provided with transmitter operating conditions for satisfying RF exposure compliance. For portable applications OEM integrators need no SAR evaluation. The max source-based time- averaged output of 0.5 mW is below the low threshold of 24mW for d < 1.5 cm. Use only the supplied or approved antenna. Unauthorized antennas, modifications or attachments could damage the terminal and may contravene local RF emission regulations or invalidate type approval. Industry Canada Otto Bock Healthcare Products GmbH Kaiserstraße 39 · 1070 Wien · Austria Tel. (+43-1) 526 95 48 · Telefax (+43-1) 526 79 85 vertrieb.austria@ottobock.com · www.ottobock.at Otto Bock has been certified by the German Society for the Certification of Quality Assurance Systems (DQS) in accordance with DIN EN ISO 9001, Reg. No. 779 ( Management System).
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 4 Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:4309d148-c8a6-4c3a-b630-5fac2a380333 Create Date : 2005:11:04 07:21:17Z Modify Date : 2006:01:11 12:59:09+01:00 Metadata Date : 2006:01:11 12:59:09+01:00 Creator Tool : Adobe InDesign 2.0.1 Version ID : 1 Rendition Class : proof:pdf Document ID : adobe:docid:indd:35774a7e-4cfb-11da-9573-de72e8451465 Rendition Of Document ID : adobe:docid:indd:35774a7e-4cfb-11da-9573-de72e8451465 Rendition Of Version ID : 1 Rendition Of Rendition Class : default Format : application/pdf Title : Trapped : False Creator : Adobe InDesign 2.0.1 Producer : Adobe PDF Library 5.0EXIF Metadata provided by EXIF.tools