OvisLink AC1200R 1200Mbps 802.11AC AP Router User Manual AirLive AC 1200R Manual
OvisLink Corp. 1200Mbps 802.11AC AP Router AirLive AC 1200R Manual
OvisLink >
User Manual
AC-1200R
1200Mbps 802.11AC
AP Router
User’s Manual
Copyright and Disclaimer
AirLive AC-1200R User’s Manual
Copyright & Disclaimer
No part of this publication may be reproduced in any form or by any means, whether
electronic, mechanical, photocopying, or recording without the written consent of OvisLink
Corp.
OvisLink Corp. has made the best effort to ensure the accuracy of the information in this
user’s guide. However, we are not liable for the inaccuracies or errors in this guide.
Please use with caution. All information is subject to change without notice
All Trademarks are properties of their respective holders.
This product requires professional installation. Please do not attempt to install the
device without the necessary knowledge in regards to your country's wireless
regulations.
Copyright and Disclaimer
AirLive AC-1200R User’s Manual
ii
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, (example - use only shielded interface
cables when connecting to computer or peripheral devices) any changes or modifications
not expressly approved by the party responsible for compliance could void the user’s
authority to operate this equipment. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
For product available in the USA/Canada market, only channel 1~11 can be operated.
Selection of other channels is not possible.
Article 12
Without permission, any company, firm or user shall not alter the frequency, increase
the power, or change the characteristics and functions of the original design of the
certified lower power frequency electric machinery.
Article 14
The application of low power frequency electric machineries shall not affect the
navigation safety nor interfere a legal communication, if an interference is found, the
service will be suspended until improvement is made and the interference no longer
exists.
Copyright and Disclaimer
AirLive AC-1200R User’s Manual
IMPORTANT NOTE
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
FCC NOTICE: To comply with FCC part 15 rules in the United States, the system must be
professionally installed to ensure compliance with the Part 15 certification. It is the
responsibility of the operator and professional installer to ensure that only certified systems
are deployed in the United States. The use of the system in any other combination (such as
co-located antennas transmitting the same information) is expressly forbidden.
© 2011, OvisLink Corporation. All rights reserved.
Table of Contents
i AirLive AC-1200R User’s Manual
Table of Contents
1. Introduction .............................................................................................. 1
1.1 Overview............................................................................................ 1
1.2 Firmware Upgrade and Tech Support ................................................ 2
1.3 Wireless Operation Modes ................................................................. 2
1.3.1 Dual Band Router Mode........................................................... 3
1.3.2 Dual AP Mode .......................................................................... 4
1.3.3 WISP + AP Mode ..................................................................... 5
1.3.4 Bridge + AP Mode .................................................................... 6
1.3.5 Client + AP Mode ..................................................................... 7
2. Installing the AC-1200R ........................................................................... 8
2.1 Before You Start ................................................................................. 8
2.2 Installing AC-1200R ........................................................................... 8
2.3 Knowing Your AC-1200R ................................................................... 9
2.3.1 Front Side Introduction ............................................................. 9
2.3.2 Back Side Introduction ............................................................10
2.4 Installation Steps ............................................................................... 11
2.4.1 Installation Steps by using LAN port ........................................ 11
2.4.2 Wireless Installation Steps ......................................................12
2.4.3 Internet Installation Steps ........................................................15
3. Configuring the AC-1200R .................................................................... 17
3.1 Important Information ....................................................................... 17
3.2 Prepare Your PC .............................................................................. 18
3.3 Management Interface ..................................................................... 19
3.3.1 Web Management (HTTP): .....................................................19
3.4 Introduction to Web Management .................................................... 19
3.4.1 Getting into Web Management ................................................19
3.4.2 Login .......................................................................................19
Table of Contents
AirLive AC-1200R User’s Manual
ii
3.5 Initial Configuration .......................................................................... 20
3.5.1 Choose the wireless Operation Modes ...................................20
3.5.2 Change the Device’s IP Address .............................................21
3.5.3 Change the Country Code ......................................................22
3.5.4 Set the Time and Date ............................................................23
3.5.5 Change Password ...................................................................23
4. Wireless and WAN Settings .................................................................. 24
4.1 About AC-1200R Menu Structure ..................................................... 24
4.2 General Wireless Settings ............................................................... 25
4.2.1 Regulatory Domain .................................................................27
4.2.2 Network SSID .........................................................................27
4.2.3 Site Survey .............................................................................28
4.2.4 Radio Mode ............................................................................29
4.2.5 Channel ..................................................................................29
4.2.6 Channel Width ........................................................................30
4.2.7 Security Settings .....................................................................30
4.2.8 Advance Settings ....................................................................33
4.2.9 Access Control (ACL) ..............................................................36
4.2.10 Multiple SSID ........................................................................37
4.2.11 QoS Setting ...........................................................................38
4.2.12 Bandwidth Control .................................................................40
4.3 AP Specific Settings ......................................................................... 42
4.4 Bridge Mode Specific Settings ......................................................... 44
4.5 Client Mode Specific Settings .......................................................... 45
4.6 Router Mode Specific Settings ......................................................... 47
4.6.1 WAN Port Settings ..................................................................48
4.6.2 PPPoE Server Settings ...........................................................50
4.6.3 DHCP Server Settings ............................................................52
4.6.4 Multiple DMZ ...........................................................................53
4.6.5 Virtual Server Settings ............................................................54
4.6.6 Special Applications ................................................................55
Table of Contents
iii AirLive AC-1200R User’s Manual
4.6.7 IP Filtering Settings .................................................................56
4.6.8 Dynamic DNS Settings ...........................................................57
4.6.9 Remote Management Settings ................................................57
4.7 WISP Specific Settings .................................................................... 58
4.7.1 WAN Port Settings ..................................................................59
4.7.2 DHCP Server Settings ............................................................61
4.7.3 Multiple DMZ ...........................................................................62
4.7.4 Virtual Server Settings ............................................................63
4.7.5 Special Applications ................................................................64
4.7.6 IP Filtering Settings .................................................................65
4.7.7 Dynamic DNS Settings ...........................................................66
4.7.8 Remote Management Settings ................................................66
5. System Configuration ............................................................................ 67
5.1 System Configuration ...................................................................... 67
5.1.1 Device IP Settings ...................................................................67
5.1.2 Time Settings ..........................................................................68
5.1.3 Password Settings ..................................................................69
5.1.4 System Management ..............................................................70
5.1.5 WAN .......................................................................................71
5.1.6 2.4G Wireless .........................................................................71
5.1.7 5G Wireless ............................................................................77
5.1.8 QoS ........................................................................................78
5.1.9 NAT .........................................................................................79
5.1.10 Firewall .................................................................................80
6. Device Status & Tools ........................................................................... 82
6.1 Status .............................................................................................. 82
6.1.1 Status ......................................................................................82
6.1.2 Internet Connection .................................................................82
6.1.3 Device Status ..........................................................................83
6.1.4 System Log .............................................................................84
6.1.5 Security Log ............................................................................84
6.1.6 Active DHCP Client .................................................................85
Table of Contents
AirLive AC-1200R User’s Manual
iv
6.1.7 Statistics..................................................................................85
6.1.8 Configuration Tools .................................................................86
6.1.9 Firmware Upgrade ..................................................................86
6.1.10 Reset ....................................................................................87
7. Frequent Asked Questions ................................................................... 88
8. Specifications ........................................................................................ 90
9. Wireless Network Glossary ................................................................... 94
1. Introduction
1 AirLive AC-1200R User’s Manual
1
1. Introduction
1.1 Overview
The AC-1200R is a multi-functional dual band concurrent AP Router that can operate in 5
different wireless modes. The AP features 2 radios that run in 5GHz or 2.4GHz frequency
band. Moreover, it supports latest standard 802.11ac which provide the higher throughout
than pervious standard.
Feature Summary
2.4G/5G Dual Band Concurrent
11ac + 11b/g/n, data rate up to 1200Mbps
5 Wireless Modes
23dBm* Hi-Power with standard antennas. ( Limit 20dBm in EU)
QoS and Bandwidth Control
Multiple SSID and VLAN
1. Introduction
AirLive AC-1200 User’s Manual
2
10/20/40/80 Channel Width
PPPoE Server
Virtual Server and DMZ support
Syslog Support
1.2 Firmware Upgrade and Tech Support
If you encounter a technical issue that can not be resolved by information on this guide, we
recommend that you visit our comprehensive website support at www.airlive.com. The tech
support FAQ are frequently updated with latest information.
In addition, you might find new firmware that either increase software functions or provide
bug fixes for AC-1200R. You can reach our on-line support center at the following link:
http://www.airlive.com/support/support_3.php
1.3 Wireless Operation Modes
The AC-1200R can perform as a multi-function wireless device. Through the AirLive web
interface, users can easily select which wireless mode they wish the AC-1200R to perform.
The AC-1200R provides 5 modes of wireless operational applications. It can transform
the AC-1200R into different roles in the wireless infrastructure. Below is the example
application table for AC-1200R.
Mode
Radio 1(5G)
Radio2(2.4G)
Applications
Dual Band Router
AP Router
AP Router
Dual Home Networks:
5GHz for Games/AV
and 2.4GHz for PC
Dual AP Mode
Access Point
Access Point
Dual Band Hotspots
WISP + AP
Client Mode
AP Router
Sharing WISP 5GHz
Broadband Wirelessly
Bridge + AP
Bridge Mode
Access Point
WDS Wireless
Repeater
Client + AP
Client
Access Point
Universal Repeater
1. Introduction
3 AirLive AC-1200R User’s Manual
1.3.1 Dual Band Router Mode
In Dual Band Concurrent mode, the radio1 works in 5GHz while radio2 works in 2.4GHz
mode. That means the AC-1200R can provide Internet service to both 5GHz (like game
network) and 2.4GHz (like PC network) at the same time.
1. Introduction
AirLive AC-1200 User’s Manual
4
1.3.2 Dual AP Mode
In Dual AP mode, both wireless interface of AC-1200R are set as AP and provide hotspot
service on each interface. Radio1 is set to 11ac mode while Radio2 is set to 11g/b/n Mode.
This mode is most useful for Dual Band Hotspot function such as in the hotels, shopping
malls, or offices.
1. Introduction
5 AirLive AC-1200R User’s Manual
1.3.3 WISP + AP Mode
In this mode, Radio1 (5GHz) acts as a client to connect with remote WISP Base Station.
Radio2 (in 11g/b/n mode) works as an AP router to allow subscriber to share the WISP
connection wirelessly. Using the AC-1200R, WISP no longer requires 2 AP/CPE to provide
wireless access in subscriber’s home or office.
1. Introduction
AirLive AC-1200 User’s Manual
6
1.3.4 Bridge + AP Mode
In this mode, Radio1 is working as Bridge mode in 5GHz while Radio 2 is working as AP
mode in 2.4GHz. This mode is useful for WISP backbone application where Radio 1 is used
for connection to another Base Station and Radio2 is used for service to subscribers. This
mode can also be used as repeater in indoor environment.
The AC-1200R’s Bridge mode can be configured as “WDS Bridge”. In WDS Bridge, you
must enter the remote AP’s MAC Address. It can connect with another AC-1200R via WDS
Bridge.
1. Introduction
7 AirLive AC-1200R User’s Manual
1.3.5 Client + AP Mode
In this mode, it can work as a wireless repeater to extend the coverage of remote wireless
router.
2. Installing the AC-1200R
AirLive AC-1200 User’s Manual
8
2
2.Installing the AC-1200R
This section describes the hardware features and the hardware installation procedure for
the AC-1200R. For software configuration, please go to chapter 3 for more details.
2.1 Before You Start
It is important to read through this section before you install the AC-1200R.
The use of 5GHz spectrum might be prohibited in some countries. Please consult with
your country’s telecom regulation first.
Please installation the antennas first before connecting the power. Connecting the
power without installing the antennas may result in damage to the wireless radios
which may void your warranty.
2.2 Installing AC-1200R
The AC-1200R package contains the following items:
One AC-1200R main unit
One 12V 1A DC power adapter
Indoor detachable dual band Omni Antenna x 2
Quick Start Guide
User’s Guide CD
2. Installing the AC-1200R
9 AirLive AC-1200R User’s Manual
2.3 Knowing Your AC-1200R
2.3.1. Front Side Introduction
LED #
Display
Description
1
Power
Solid Green LED while the device is powered on,
either by power adaptor or PoE.
2
2.4G
Solid Green LED while the device is powered on.
Blinking while there is Data transmission, dark when
this interface is turn off.
3
5G
4~8
LAN
WAN
LAN ports status LED, Solid Green LED shows
when a port is actively connected, blinking while
there is data transmission, turns into dark when this
disconnected. LAN5 is also the WAN port
2. Installing the AC-1200R
AirLive AC-1200 User’s Manual
10
2.3.2. Back Side Introduction
Port #
Display
Description
1
WLAN1
Detachable antenna with R-SMA connector. 2
indoor dual band antennas are delivered.
2
Power Adaptor
12V 1A power supply adaptor delivered with
product.
3
WPS/Reset
It works as WPS or Reset button. Push 15 sec
of the button, the device will reset to default
4
WAN Port
WAN Port. When it is in Dual Band Router
mode, it function as a WAN port. In Dual AP
mode , it work as LAN port
5~8
LAN
LAN port
9
WLAN2
Detachable antenna with R-SMA connector.
2. Installing the AC-1200R
11 AirLive AC-1200R User’s Manual
2.4 Installation Steps
This section describes installation steps required for the AC-1200R before it can work
properly in your network.
2.4.1. Installation Steps by using LAN port
1. Install antennas into the AC-1200R
2. Connect the broadband line into the WAN port of the AC-1200R
3. Connect your PC to any LAN port.
4. Connect the power jack to the power port.
5. Wait for 5 minutes. Then open the browser on your PC and type in "192.168.1.254"
to reach the web management
6. For software configuration, please go to chapter 3 for more details.
2. Installing the AC-1200R
AirLive AC-1200 User’s Manual
12
2.4.2. Wireless Installation Steps
1. Install antennas into the AC-1200R
2. Connect the broadband line into the WAN port of the AC-1200R
3. Connect the power jack to the power port.
4. Wait for 5 minutes. Then on your Notebook PC, scan and connect to “airlive”
wireless network
5. Open your web browser and type “192.168.1.254” to configure your AC-1200R
6. When prompt for username/password, type “admin” as username and “airlive” as
password
7. When the following screen appears, click on “Setup” to configure wireless settings.
2. Installing the AC-1200R
13 AirLive AC-1200R User’s Manual
8. Select “Change Settings for: Radio2”. Then click on “Security Settings”
2. Installing the AC-1200R
AirLive AC-1200 User’s Manual
14
9. Choose WPA2-PSK and enter your own encryption key (please write down and do
not forget it is case sensitive). Then click on “Apply” button
10. The AC-1200R will reboot. After about 3 minutes, please try to access the network
again. You will be prompted to enter your encryption key.
2. Installing the AC-1200R
15 AirLive AC-1200R User’s Manual
2.4.3. Internet Installation Steps
Please finish the LAN port and Wireless installations first in 2.4.1 and 2.4.2 before
performing the following steps.
If you are using AC-1200R as a router, please follow the steps below:
1. Please make sure the Internet line is connected to the WAN port.
2. Open your web browser and type 192.168.1.254
3. When prompt for password, enter “admin” for username and “airlive” for password.
4. Choose “Wireless Settings” on Welcome Screen and click on “Setup”
5. Choose “WAN Port Settings” on the bottom.
6. Please enter your ISP’s authentication Information and Click on “Apply” button. Here
are some guidelines.
2. Installing the AC-1200R
AirLive AC-1200 User’s Manual
16
If your Internet connection is ADSL, it is most likely using the following option:
Your ISP already provides you with PPPoE authentication information,
select this button and enter the information below:
If your internet connection is Cable Modem, it is most likely to use the option:
If your ISP already provides you with a Host Name, select this button and
enter the information below: (DHCP)
However, please still consult with your ISP about the correct account information.
7. Click on “Apply” to finish.
3. Configuring the AC-1200R
17 AirLive AC-1200R User’s Manual
3
3.Configuring the
AC-1200R
The AC-1200R offers web based management interface. You can configure through
standard web browser (http). In this chapter, we will explain AC-1200R’s available
management interfaces and how to get into them. Then, we will provide the introduction on
Web Management and recommended initial settings.
3.1 Important Information
The following information will help you to get start quickly. However, we recommend you to
read through the entire manual before you start. Please note the password and SSID are
case sensitive.
The default IP address is: 192.168.1.254 Subnet Mask: 255.255.255.0
When using Web UI, the login as follow:
User name: admin
Password: airlive
The default radio mode for Radio 1 is 802.11ac/n
The default radio mode for Radio 2 is 802.11g/b/n
The default SSID for Radio 1 is: AirLive
The default SSID for Radio 2 is: AirLive 5G
The default wireless mode is : Dual Band Router Mode
After power on, please wait for 2 minutes for AC-1200R to finish boot up
Please remember to click on “Apply” for new settings to take effect
3. Configuring the AC-1200R
AirLive AC-1200 User’s Manual
18
3.2 Prepare Your PC
The AC-1200R can be managed remotely by a PC through either the wired or wireless
network. The default IP address of the AC-1200R is 192.168.1.254 with a subnet mask of
255.255.255.0. This means the IP address of the PC should be in the range of 192.168.1.1
to 192.168.1.253.
The default mode for AC-1200R is “Dual Band Router” mode. In this mode, the AC-1200R’s
DHCP server is turned on; therefore, your PC can get IP automatically from AC-1200R. You
just need to set your PC to “Obtain IP address automatically” on the TCP/IP setting. By
default, Windows already do this so you do not need to change.
However, if you are using AC-1200R in non-router modes (Dual AP, Dual Band Router,
WDS+AP, Cllient+AP), you need to set your IP manually. To prepare your PC for
management with the AC-1200R, please do the following:
1. Connect your PC directly to the LAN port on the DC Injector of AC-1200R
2. Set your PC’s IP address manually to 192.168.1.100 (or other address in the same
subnet)
You are ready now to configure the AC-1200R using your PC.
3. Configuring the AC-1200R
19 AirLive AC-1200R User’s Manual
3.3 Management Interface
The AC-1200R can be configured using web management interfaces below:
3.3.1 Web Management (HTTP):
You can manage your AC-1200R by simply typing its IP address in the web browser. Most
functions of AC-1200R can be accessed by web management interface. We recommend
using this interface for initial configurations. To begin, simply enter AC-1200R’s IP address
(default is 192.168.1.254) on the web browser. The default user name is “admin”; default
password is “airlive”.
3.4 Introduction to Web Management
3.4.1 Getting into Web Management
Normal Web Management (HTTP)
To get into the Normal Web Management, simply type in the AC-1200R’s IP address
(default IP is 192.168.1.254) into the web browser’s address field.
3.4.2 Login
After the procedure above, the Login username and password is required.
Please type in the username and password. The default username is “admin” and
password is “airlive”. After that Operation Mode page will appear.
3. Configuring the AC-1200R
AirLive AC-1200 User’s Manual
20
3.5 Initial Configuration
We recommend users to browse through AC-1200R’s web management interface to get an
overall picture of the functions and interface. Below are the recommended initial
configurations for first time login:
3.5.1 Choose the wireless Operation Modes
The wireless settings of AC-1200R are dependent on the wireless operation mode you
choose. Therefore, the first step is to choose the operation mode. For explanation on when
to use what operation mode, please refer to Chapter 1.
Follow the example below to change to “WISP + AP” mode
1. Select “WISP + AP” mode
2. Click on “setup” button
3. The AP will reboot, wait for about one minute
1
Wizard to setup Dual
Band Router Mode
Click to configure wireless settings
2
3. Configuring the AC-1200R
21 AirLive AC-1200R User’s Manual
3.5.2 Change the Device’s IP Address
The default IP address is at 192.168.1.254. You should change it to the same subnet as
your network. Also, if you want to manage AC-1200R remotely, you have to set the
Gateway and DNS server information.
To setup the IP settings for AC-1200R, please select “General Setup” -> LAN”. After
entering the IP information, click on “Apply” to finish.
3. Configuring the AC-1200R
AirLive AC-1200 User’s Manual
22
3.5.3 Change the Country Code
The legal frequency and channels in 5GHz spectrum varies between countries. The default
country code is ETSI which should require no changes If you are living in Europe. If you are
living outside EU, you should change the country code accordingly. In the example below,
we will change the country code to FCC
Step 1. Select “Operation Mode” -> “Setup”
Step 2. From the Regulatory Domain, please select your country and click on “Apply”
to finish.
3. Configuring the AC-1200R
23 AirLive AC-1200R User’s Manual
3.5.4 Set the Time and Date
It is important that you set the date and time for your AC-1200R so that the system log will
record the correct date and time information. Please go to “System Configuration” ->Time
Settings. We recommend you choose “Enable NTP” so the time will be keep even after
reboot. If your AC-1200R is not connected to Internet, please enter the time manually.
Please remember to select your local time zone and click “Apply” to finish.
3.5.5 Change Password
You should change the password for AC-1200R at the first login. To change password,
please go to “General Setup -> “Password Settings” menu.
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
24
4
4.Wireless and WAN
Settings
In this chapter, we will explain about the wireless settings and router mode settings in web
management interface. Please be sure to read through Chapter 3’s “Introduction to Web
Management” and “Initial Configurations” first. For system configurations, device status,
and other non-wireless related settings; please go to Chapter 5.
4.1 About AC-1200R Menu Structure
The AC-1200R’s web management menu is divided into 4 main sections: Operation
Modes, General Setup, Tools and Status. The main menus’ options are always displayed
on the top of the web management page. Within each main menu category, there are
sub-menu options which are displayed on the side of the web management page.
Top Menu Bar
Side Menu Bar
4. Wireless and WAN Settings
25 AirLive AC-1200R User’s Manual
Operation Mode: This menu is where you will find wireless and WAN settings. The
AC-1200R’s wireless settings are dependent on the wireless operation mode you
choose; only the applicable wireless settings for selected operation mode are shown.
For example; WAN port setting is available only for AP Router and WISP Router mode,
it will only be shown in those modes. To access wireless settings, click on the “Setup”
button within each operation mode. For explanation on different wireless modes,
please refer to Chapter 1. We will talk about functions in this menu for this chapter.
General Setup: All settings besides Wireless and WAN functions are in this category.
The system configuration including changing password, upload firmware, backup
configuration, settings PING watchdog, and setting management interface. We will
talk about this menu’s function in Chapter 5.
Tools: Discover network status using ping, trace route and other tools
Status: This section for monitoring the status of AC-1200R. It provides information on
device status, Ethernet status, wireless status, wireless client table, and system log.
4.2 General Wireless Settings
The wireless settings of AC-1200R are dependent on the wireless operation mode you
choose. Therefore, the first step is to choose the operation mode. For explanation on when
to use what operation mode, please refer to Chapter 1.
When you select “Wireless Settings” in the welcome screen, or click on the “Operation
Mode” on the top menu; the following screen will appear:
This tells your
current operation
mode now
Select one of the
wireless
operation modes
here
Configure Wireless and WAN
settings
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
26
Mode: The available wireless operation modes for AC-1200R. Select one and click on
“Change Mode” button to switch between modes.
Setup: Click here to configure the Wireless and WAN (in router mode) settings.
Once you click on the “Setup” page, the wireless settings will appear
4. Wireless and WAN Settings
27 AirLive AC-1200R User’s Manual
The AC-1200R device provides all 14 modes of wireless operational applications with:
Mode
Radio 1(11a)
Radio2(11a/b/g)
Applications
Dual Band Router
AP Router
AP Router
Dual Home Networks:
5GHz for Games/AV
and 2.4GHz for PC
Dual AP Mode
Access Point
Access Point
Dual Band Hotspots
WISP + AP
Client Mode
AP Router
Sharing WISP 5GHz
Broadband Wirelessly
WDS + AP
WDS Bridge
Mode
Access Point
WDS Wireless
Repeater
Client + AP
Client
Access Point
Universal Repeater
4.2.1 Regulatory Domain
Operation Mode -> Setup -> Regulatory Domain
The legal frequency and channels in 5GHz spectrum varies between countries. Please
select your country from here. It is for compatibility testing only. Please make sure the
channel you used is allowed in your country when select this special domain.
4.2.2 Network SSID
Operation Mode -> Setup -> Network SSID
The SSID is the network name used to identify a wireless network. The SSID must be the
same for all devices in the same wireless network. In AC-1200R, it is possible to create
more than one SSID or guest Mode in AP and AP Router mode, please check the
“General Setup2.4G-> Guest” for 2.4 radio and “General Setup5G-> Guest” for 5G
radio. The SSID length is up to 32 characters. The default SSID is “airlive”.
Enable Radio 1/2: The default wireless is on. You can uncheck this box to disable
wireless interface.
Disable SSID Broadcasting: If you check this box, the SSID will be hidden; only users
who know the SSID can associate with this network.
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
28
4.2.3 Site Survey
Operation Mode -> Setup -> Site Survey
The Site Survey function in AC-1200R provides 4 important functions
In Client and Bridge Infrastructure mode, site survey will scan for available AP
network. Then allow user to select and connect to the AP. These greatly
simplify the installation.
Once Site Survey displays the available AP or Bridge networks, you can
select a particular SSID to display its RSSI value continuously. This function is
called “Signal Survey”. Signal Survey can be used for antenna alignment.
For WDS Bridge mode, the Site Survey will scan for available AP and Bridge
networks. User can then find the MAC address (BSSID) of the remote
Bridges.
For AP and AP router mode, the Site Survey allows administrator to check
what channels are already occupied for choosing a cleaner channel.
When you click on Site Survey, the following screen will appear. It might take a few minutes
to scan all the channels in the 2.4G or 5GHz spectrum.
Click here to select
SSID for Association
or Signal Survey
For antenna alignment, it
will display and update
signal value after refresh
button is clicked
To connect with the selected
SSID, this function is available
only in Client Infrastructure or
Bridge Infrastructure
4. Wireless and WAN Settings
29 AirLive AC-1200R User’s Manual
Done: Please choose a SSID before click on this button. This button is available only in
Client Infrastructure or Bridge Infrastructure modes. Once you click on this button,
AC-1200R will attempt to make a connection with the selected ESSID. If there is
encryption needed, the AC-1200R will prompt you to enter the encryption key. Please
make sure you enter the correct encryption key, the AC-1200R will not check whether
the encryption key is correct.
Signal: Signal is a value to show the Signal Level for other access point R. In general,
remote APs with stronger signal will display higher signal values. For RSSI value, the
smaller the absolute value is, the stronger the signal.
4.2.4 Radio Mode
Operation Mode -> Setup -> Radio Mode
AC-1200R has different options for WLAN transmission. All devices in the same network
should use the same WLAN mode. In radio 1 (5G), 6 options can be selected: A+N+AC ,
N+AC, AC,A+N,N,A
In radio 2 (2.4G): 5 options can be selected: B+G+N,G,B+G, N,B
4.2.5 Channel
Operation Mode -> Setup -> Channel
The channel is the frequency range used by radio. In 802.11ac standard, each channel
occupies 80MHz width. For 2 wireless devices to connect, they must use the same
channel. The number of available legal channels might be different between countries. If
you are living outside EU, please change the country from the “Regulatory Domain” option
in this page.
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
30
4.2.6 Channel Width
Operation Mode -> Setup -> Channel Width
In radio1 (5G) spec, each channel occupies 20MHz channel width. Therefore, each
channel will jump by number of 4 (i.e. 36, 40, 44…etc). You can change the Channel Width
to 10MHz (Half) or 5MHz (Quarter) to either increase performance or reduce the
interference problem.
Auto(20/40/80MHz): This is the default channel width specified by IEEE 802.11ac
specification
20/40: Using this option would reduce the interference when AC-1200R is deployment
in congested areas. However, the performance will also drop by half when using this
option.
20MHz: It is a good choice for deployment in very congested areas. However, the
performance will also drop greatly when using this option.
4.2.7 Security Settings
Operation Mode -> Setup -> Security Settings
Security settings allow you to use encryption to secure your data from eavesdropping.
You can select different security policy to provide association authentication and/or data
encryption. The AC-1200R features various security policies including WEP, WPA radius,
WPA, WPA-PSK, WPA2, and WPA2-PSK. Please note not all security policies are
available in all operation modes. For example, only WEP is available currently in WDS
Bridge mode. All wireless devices on the same network must use the same security policy.
We recommend using WPA-PSK or WPA2-PSK whenever possible.
WEP: WEP Encryption is the oldest and most available encryption method. However, it is
also the least secure.
4. Wireless and WAN Settings
31 AirLive AC-1200R User’s Manual
Select one of the WEP key for wireless network: There are total of 4 possible keys
for WEP encryption. You need to choose which key will be used for encryption. All
wireless devices on the same network have to use the same settings. We recommend
using WEP Key 1 as in default setting.
WEP Keys: Please enter the WEP keys used for encryption. You need to fill at least
the “Select WEP Key”. For example; if you choose “Encrypt Data with WEP Key 1” in
the previous field, then it is necessary to fill WEP Key 1. The length of key is
dependant on the Key Length and Key type you choose.
Key Length: The AC-1200R offers 64bit, 128 bit, and 152 bit for WEP key length. The
longer the Key Length, the more secure the encryption is.
Key Type: 2 types are available: ASCII and HEX. ASCII is a string of ASCII code
including alphabetical characters, space, signs and numbers (i.e. “airlivepass12”). HEX
is a string of 16-bit hexadecimal digits (0..9, a, b, c, d, e, f). All wireless devices on the
network must match the exact key length and Key type. Some Wireless clients only
allow HEX type for WEP.
ASCII-64: This is a key with 64-bit key length of ASCII type. Please enter 5 ASCII
Characters if you choose this option. For example, “passw”
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
32
HEX-64: This is a key with 64-bit key length of HEX type. Please enter 10 Hexadecimal
digits if you choose this option. For example, “12345abcdef”
ASCII-128: This is a key with 64-bit key length of ASCII type. Please enter 13 ASCII
Characters if you choose this option. For example, “airlivewepkey”
HEX-128: This is a key with 128-bit key length of HEX type. Please enter 26
Hexadecimal digits if you choose this option. For example,
“1234567890abcdef1234567890”
WPA radius: WPA radius allows users to leverage a RADIUS server to do association
authentications.
UTo Enable RADIUS Server:
Server IP: The IP address of the RADIUS server.
Port Number: The port number that your RADIUS server uses for
authentication. The default setting is 1812.
Radius Server Password: This is used by your RADIUS server in the
Shared Secret field in RADIUS protocol messages. The password configured
in the AC-1200R must match the password configured in the RADIUS server.
The password can contain up to 64 alphanumeric characters.
4. Wireless and WAN Settings
33 AirLive AC-1200R User’s Manual
WPA-PSK, WPA2-PSK: Wi-Fi Protected Access (WPA) with Pre-Shared Key (PSK)
provides better security than WEP keys. It does not require a RADIUS server in order to
provide association authentication, but you do have to enter a shared key for the
authentication purpose. The encryption key is generated automatically and dynamically.
WPA2-PSK adds AES encryption for even better security. WPA2 mixed tries to authenticate
wireless clients using WPA-PSK or WPA2-PSK.
Pre-shared Key: This is an ASCII string with 8 to 63 characters. Please make
sure that both the AC-1200R and the wireless client stations use the same
key.
WPA unicast Cipher Suite: There are three cipher suite : WPA
(TKIP),WPA2(AES), WPA2 Mixed
Pre-shared Key format: To select the key format
4.2.8 Advance Settings
Operation Mode -> Setup -> Advance Settings
This page includes all the wireless settings that change the RF behaviors of AC-1200R. It is
important to read through this section before attempting to make changes.
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
34
Beacon Interval: Beacon Interval: The device broadcasts beacon frames regularly to
announce its existence. The beacon Interval specifies how often beacon frames are
transmitted in time unit of milliseconds. The default value is 100, and a valid value
should be between 1 and 65,535.
RTS Threshold: RTS/CTS frames are used to gain control of the medium for
transmission. Any unicast (data or control) frames larger than specified RTS threshold
must be transmitted following the RTS/CTS handshake exchange mechanism. The
RTS threshold should have a value between 256-2347 bytes, with a default of 2347. It
is recommended that this value does not deviate from the default too much.
Fragmentation Threshold: When the size of a unicast frame exceeds the
fragmentation threshold, it will be fragmented before the transmission. It should have a
value of 256-2346 bytes, with a default of 2346. If you experience a high packet error
rate, you should slightly decrease the Fragmentation Threshold.
DTIM Interval: The AC-1200R buffers packets for stations that operate in the
4. Wireless and WAN Settings
35 AirLive AC-1200R User’s Manual
power-saving mode. The Delivery Traffic Indication Message (DTIM) informs such
power-conserving stations that there are packets waiting to be received by them. The
DTIM interval specifies how often the beacon frame should contain DTIMs. It should
have a value between 1 to 255, with a default value of 3.
Transmit Power: You can adjust the transmit output power of the AC-1200R’s radio
from 10dBm to 24dBm. The higher the output power, the more distance AC-1200R can
deliver. However, it is advised that you use just enough output power so it will not
create excessive interference for the environment. Also, using too much power at close
distance can create serious performance drop due to signal distortion. At less than
200meter distance, the best output power is about 14dBm. At 2km distance; the best
output power setting is 18dBm for “11a”.
Data Rate: Select here to change the Data Rate for the radio. Lower data rate
sometimes provide longer distance. In most cases, however, we recommend to keep
the setting at “Auto
Enable 802.1d STP: Enable the Spanning Tree Protocol to prevent forming a network
loop. This option is especially important for WDS Bridge mode.
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
36
4.2.9 Access Control (ACL)
Operation Mode -> Setup -> Access Control
The AC-1200R allows you to define a list of MAC addresses that are allowed or denied to
access the wireless network. This function is available only for Access Point and AP Router
modes.
To add a MAC address into the table, enter a Mnemonic Name and the MAC Address, and
then click Add. The table lists all configured MAC Filter entries.
To delete entries, check the corresponding Select boxes and then press Delete Selected or
delete all.
4. Wireless and WAN Settings
37 AirLive AC-1200R User’s Manual
4.2.10 Multiple SSID
Operation Mode -> Setup -> Multiple SSID
This function is available only for Access Point and AP Router modes. Multiple SSID also
known as guess mode allows AC-1200R to create up to 1 different wireless networks
(SSID). It is also known as “Virtual AP or guess” function. Each SSID can have its
Encryption type. The users who access the Guess mode SSID can not access the
AC-1200R.
Configuring the Multiple SSID
When you click on the “Multiple SSID” button, the following screen will appear.
To set the SSID for the
Guest Network
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
38
How to enable Guess SSID
You can add 1 SSID for guest in each radio. Please follow the procedure below:
1. Enter the Wireless Guest Name (SSID) name (i.e. BridgeNet)
2. Select the Security Policy (i.e. WPA-PSK)
3. Enter the Security Key (i.e. BridgeNetKey).
4. Click on “Apply” to add SSID
How to disable guess SSID
To disable the guess SSID, please uncheck the “Enable Guess SSID”.
4.2.11 QoS Setting
Operation Mode -> Setup -> QoS Setting
QoS also known as the Bandwidth Control, administrator can set up the bandwidth for each
IP address.
4. Wireless and WAN Settings
39 AirLive AC-1200R User’s Manual
Configure the QoS Parameters
Rule Name: Set the name for the rule
Bandwidth: Set the number which you want to limit
Local IP address: Set the IP address which you want to manage
Local Port Range: Set the port number for which you want to manage
Remote IP address: Set the IP address
Remote Port Range: Set the port range
Specific the Traffic Type: Select the specific traffic you want to manage
Protocol: select the QoS protocol: TCP or UDP
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
40
4.2.12 Bandwidth Control
Operation Mode -> Setup -> QoS
QoS also known as Bandwidth Control can limit the maximum speed of entire wireless
interface or individual device. It is also known as Traffic Shaping. The AC-1200R provides
both Total Bandwidth and Per-User Bandwidth Control for both uplink and downlink speed.
It controls the speed of both wireless and wired interface.
To configure, please click on the “Bandwidth Control” button under wireless settings. The
following screen will appear:
Check to
enable
Bandwidth
Control
After enabling Bandwidth
Control and selecting
“Total” or “Per User” type,
click here to Apply
Settings for Total
Bandwidth Control
Settings for Per-User
Bandwidth Control
4. Wireless and WAN Settings
41 AirLive AC-1200R User’s Manual
Enable Bandwidth: Check to enable Bandwidth Control. Uncheck to disable it. The
default value is disabled.
Total Download Bandwidth: Total Download Bandwidth control limit the bandwidth
which all users can download from the WAN. Enter speed you wish to limit the
download traffic in Kbps
Total Upload Bandwidth: Enter the speed you wish to limit the upload traffic in Kbps
units.
QoS table: QoS table can limit speed of individual PC and network device. The AC-1200R
allows multiple rule for QoS bandwidth control and it can limit the bandwidth by IP address,
Port segment. Please first enable the Bandwidth Control, then click add to add the Rule.
Rule Name: Enter a description for the bandwidth policy. For example, “VIP”
subscriber
Bandwidth: To set the download, upload bandwidth limited
IP address: To limit the bandwidth of one single MAC address
Port Range: This is available only in WISP router and AP Router
mode. It can limit the bandwidth by application ports.
Traffic type: This option is special for WISP router and AP Router mode. It
can limit the bandwidth of HTTP, FTP,POP3, and SMTP traffic.
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
42
4.3 AP Specific Settings
The Access Point mode is the most basic mode of multi-function Access Point. In this mode,
the AP will act as a central hub for different Wireless LAN clients. Some hotspot Access
Points requires 802.1x authenticator function to authenticate a user before providing
internet service.
4. Wireless and WAN Settings
43 AirLive AC-1200R User’s Manual
Enable Radio: Use this check box to turn on or turn off the radio.
Network ID (SSID): This is to change your SSID.
Disable SSID Broadcasting: Enable the check box if you want to hide your
SSID in the network. This prevent an un-welcomed client survey your radio.
Radio Mode: Connection modes on AC-1200R and its wireless client. Note
that the client must support the same mode as AC-1200R to connect.
Channel: The radio for channel in Radio 1 (5G) and Radio 2 (2.4G) is totally
depend on the country regulation
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
44
4.4 Bridge Mode Specific Settings
The AC-1200R supports WDS Bridge connection. In a WDS network, each node can have
up to 4 connections.
WDS Bridges are using BSSID (AP’s Wireless MAC address) to authenticate each other.
Therefore, it is necessary to know the remote Bridge’s wireless MAC addresses. You can
always do a “Site Survey” to find out the MAC Addresses. You also need to set the same
encryption with remote Bridge. You can set up the encryption in Security Setting.
Here are the encryption key
settings for WEP. Please
make sure all bridges in the
WDS network enter the
same keys.
4. Wireless and WAN Settings
45 AirLive AC-1200R User’s Manual
4.5 Client Mode Specific Settings
Client mode is also known as Ethernet Client. In this mode, the AP will act as a WLAN card
to connect with the remote AP. Users can connect PC or local LAN to the Ethernet port of
local LAN to the Ethernet port of the client mode AP. This mode is mostly used as a CPE
device for WISP subscriber.
1. To connect to an access point, use the “Site Survey” button to find the Access
Point.
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
46
2. The Site Survey pop up window then shows up and lists available access point
with relative information.
3. After the access point is selected, its SSID shows automatically in the Network ID
(SSID) field.
Select the access point you want to connect
and then click the “Done” button.
4. Wireless and WAN Settings
47 AirLive AC-1200R User’s Manual
4.6 Router Mode Specific Settings
In Router mode, router functions are added between one Ethernet port and other network
interfaces. Therefore, the ISP subscriber can share the ISP connection without need for
extra router.
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
48
4.6.1 WAN Port Settings
Operation Mode -> Setup -> WAN Port Settings
The AC-1200R support different authentication and IP assignment standards for the WAN
port. It includes fixed IP, DHCP, PPPoE and PPTP protocols. Please consult with your ISP
about what authentication type is used for the WAN port connection.
Clone MAC Address: Some service provider (Cable Modem provider) lock to
certain MAC address. In this situation, the WAN port of AC-1200R needs to
clone the MAC address. Please check the “Clone MAC address” box and
enter the address that need to be cloned.
4. Wireless and WAN Settings
49 AirLive AC-1200R User’s Manual
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
50
4.6.2 PPPoE Server Settings
The PPPoE server setting is only available when the AC-1200R is in Dual Band Router
mode. The maximum number of concurrent accounts is 14.
Operation Mode -> Setup -> PPPoE Server Settings
Enable/Disable: Used to enable or disable PPPoE server.
Authentication: Choose to use “Local Account” or “Radius” as authentication
mechanism. If choosing “Local Account”, you have to configure “Local Account
Management”. If choosing “Radius”, you have to configure Radius server.
Local IP Address: Assign IP address to the interface of PPPoE server.
Remote Start/Remote End IP: Define IP address pool that is used to assign
address to the connected PPPoE clients.
4. Wireless and WAN Settings
51 AirLive AC-1200R User’s Manual
MPPE Encryption: Used to enable or disable special MPPE encryption function.
Compression: Used to enable compression function.
Local Account Management
User Name: Specify authentication username.
Password: Specify authentication password.
Assign IP: Specify the IP address of PPPoE client. If 0.0.0.0 is specified, then
PPPoE client will get an IP address between remote start IP and remote end
IP.
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
52
4.6.3 DHCP Server Settings
Operation Mode -> Setup -> DHCP Server Settings
DHCP Server Settings is to assign private IP address to the devices in your local area
network (LAN). Note that AC-1200R keeps the IP address of 192.168.1.254 and act as the
default gateway of the LAN.
You can assign IP address to MAC address; the DHCP server will keep the IP for the MAC
address.
Manually
assign MAC
address to IP
here
Change IP
range and IP
Lease Time
here
Change
AC-1200R IP
address
4. Wireless and WAN Settings
53 AirLive AC-1200R User’s Manual
4.6.4 Multiple DMZ
Operation Mode -> Setup -> Multiple DMZ
Multiple DMZ opens all TCP/UDP ports to particular IP address on the LAN side. It allows
setting up servers behind the AC-1200R.
Select a DMZ type and then enter the local DMZ IP address
Note: A DMZ server is a common term used to describe the default virtual server. If the
DMZ server is selected, Internet traffic not destined for a valid virtual server is redirected to
this privately addressed LAN client. This can be used together with a separate firewall
device to perform additional security functions.
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
54
4.6.5 Virtual Server Settings
Operation Mode -> Setup -> Virtual Setting
This allows you to specify one or more applications running on server computers on the
LAN that may be accessed by any Internet user. Internet data destined for the specified
public port will be directed to the specified private port number on the LAN client with the
specified private IP address.
4. Wireless and WAN Settings
55 AirLive AC-1200R User’s Manual
4.6.6 Special Applications
Operation Mode -> Setup -> Special Applications
Some Internet application such as Instant Messaging or games use groups of ports, and
are not easy to work behind a firewall. To work well with these special applications we will
open ports to let traffic pass through.
Note: You can use up to 3 sets of opened ports for a specific application. The opened ports
can be separated by a comma and no spaces are allowed (e.g. 2300-2305, 4300-4305,
5300-5305).
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
56
4.6.7 IP Filtering Settings
Operation Mode -> Setup -> IP Filtering Settings
IP Filtering Settings allows users to define the traffic type permitted or not permitted in your
LAN. You can control which PC client uses what services in which they can have access to
these services. If both of MAC filtering and IP filtering are enabled simultaneously, the MAC
filtering table will be checked first and then IP filtering table
This allows you to define who are allowing / denying access from / to the Internet.
Enable MAC Filtering: To enable the MAC filtering.
Enable IP Filtering : To enable the IP filtering
Allow: Data traffic satisfying rules below are allowed / forwarded.
Deny: Data traffic satisfying rules below are denied / filtered.
To grant or deny IP address, select ADD ,ADD PC or Reset.
4. Wireless and WAN Settings
57 AirLive AC-1200R User’s Manual
4.6.8 Dynamic DNS Settings
Operation Mode -> Setup -> Dynamic DNS Settings
Dynamic DNS (DDNS) allows you to create a hostname that points to your dynamic IP or
static IP address or URL. AC-1200R provide Dynamic DNS client using DynDNS, please
visit http://dyn.com/dns/ for detail.
4.6.9 Remote Management Settings
Operation Mode -> Setup -> Remote Management
The remote management function allows you to designate a host in the Internet to have
management/configuration access to the Wireless Router from a remote site. Enter the
designated host IP Address in the Host IP Address field.
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
58
4.7 WISP Specific Settings
In WISP mode, the AP will behave just the same as the Client mode for wireless function.
However, router functions are added between the wireless WAN side and the Ethernet LAN
side. Therefore, the WISP subscriber can share the WISP connection without need for
extra router.
WISP mode acts both in AP and Router which included in these operation modes: WISP +
AP.
In WISP + AP mode, the Radio 1 is actually a wireless client of the WISP wireless node and
also the gateway of the local area network.
Router mode acts both in AP and Router which included in these operation modes: Dual
Band Router
4. Wireless and WAN Settings
59 AirLive AC-1200R User’s Manual
4.7.1 WAN Port Settings
Operation Mode -> Setup -> WAN Port Settings
The AC-1200R support different authentication and IP assignment standards for the WAN
port. It includes fixed IP, DHCP, PPPoE and PPTP protocols. Please consult with your ISP
about what authentication type is used for the WAN port connection.
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
60
Clone MAC Address: Some service provider (Cable Modem provider) lock to
certain MAC address. In this situation, the WAN port of AC-1200R needs to
clone the MAC address. Please check the “Clone MAC address” box and
enter the address that need to be cloned.
4. Wireless and WAN Settings
61 AirLive AC-1200R User’s Manual
4.7.2 DHCP Server Settings
Operation Mode -> Setup -> DHCP Server Settings
DHCP Server Settings is to assign private IP address to the devices in your local area
network (LAN). Note that AC-1200R keeps the IP address of 192.168.1.1 and act as the
default gateway of the LAN.
You can assign IP address to MAC address; the DHCP server will keep the IP for the MAC
address.
Manually assign
MAC address to IP
here
Change IP range
and IP Lease
Time here
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
62
4.7.3 Multiple DMZ
Operation Mode -> Setup -> Multiple DMZ
Multiple DMZ opens all TCP/UDP ports to particular IP address on the LAN side. It allows
setting up servers behind the AC-1200R.
Select a DMZ type and then enter the local DMZ IP address
Note: A DMZ server is a common term used to describe the default virtual server. If the
DMZ server is selected, Internet traffic not destined for a valid virtual server is redirected to
this privately addressed LAN client. This can be used together with a separate firewall
device to perform additional security functions.
4. Wireless and WAN Settings
63 AirLive AC-1200R User’s Manual
4.7.4 Virtual Server Settings
Operation Mode -> Setup -> Virtual Setting
This allows you to specify one or more applications running on server computers on the
LAN that may be accessed by any Internet user. Internet data destined for the specified
public port will be directed to the specified private port number on the LAN client with the
specified private IP address.
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
64
4.7.5 Special Applications
Operation Mode -> Setup -> Special Applications
Some Internet application such as Instant Messaging or games use groups of ports, and
are not easy to work behind a firewall. To work well with these special applications we will
open ports to let traffic pass through.
Note: You can use up to 3 sets of opened ports for a specific application. The opened ports
can be separated by a comma and no spaces are allowed (e.g. 2300-2305, 4300-4305,
5300-5305).
4. Wireless and WAN Settings
65 AirLive AC-1200R User’s Manual
4.7.6 IP Filtering Settings
Operation Mode -> Setup -> IP Filtering Settings
IP Filtering Settings allows users to define the traffic type permitted or not permitted in your
LAN. You can control which PC client uses what services in which they can have access to
these services. If both of MAC filtering and IP filtering are enabled simultaneously, the MAC
filtering table will be checked first and then IP filtering table
This allows you to define who are allowing / denying access from / to the Internet.
Enable MAC Filtering: To enable the MAC filtering.
Enable IP Filtering : To enable the IP filtering
Allow: Data traffic satisfying rules below are allowed / forwarded.
Deny: Data traffic satisfying rules below are denied / filtered.
To grant or deny IP address, select ADD ,ADD PC or Reset.
4. Wireless and WAN Settings
AirLive AC-1200 User’s Manual
66
4.7.7 Dynamic DNS Settings
Operation Mode -> Setup -> Dynamic DNS Settings
Dynamic DNS (DDNS) allows you to create a hostname that points to your dynamic IP or
static IP address or URL. AC-1200R provide Dynamic DNS client using DynDNS, please
visit http://www.dyndns.orgUH for detail.
4.7.8 Remote Management Settings
Operation Mode -> Setup -> Remote Management
The remote management function allows you to designate a host in the Internet to have
management/configuration access to the Wireless Router from a remote site. Enter the
designated host IP Address in the Host IP Address field.
5. System Configuration
67 AirLive AC-1200R User’s Manual
In this chapter, we will explain about General Setup in web management interface. Please
be sure to read through Chapter 3’s “Introduction to Web Management” and “Initial
Configurations” first.
5.1 System Configuration
When you click on the “General Setup” menu on the top menu bar, the following screen will
appear. The system configuration includes all non-wireless settings. We will explain their
functions here.
5.1.1 Device IP Settings
General Setup >> LAN
The LAN Settings screen allows you to configure the IP address and subnet of the device.
You also can enable or disable the DHCP server in this page. If AC-1200R is working in
client mode or AP mode, please disable the DHCP server.
The DHCP server setting, please refer the chapter 4.6.3
5
5. System Configuration
5. System Configuration
AirLive AC-1200 User’s Manual
68
5.1.2 Time Settings
General Setup >>System ->Time Zone
It is important that you set the date and time for your AC-1200R so that the system log will
record the correct date and time information. We recommend you choose “Enable NTP” so
the time will be keep even after reboot. If your AC-1200R is not connected to Internet,
please enter the time manually. Please remember to select your local time zone and click
“Apply” to finish.
5. System Configuration
69 AirLive AC-1200R User’s Manual
5.1.3 Password Settings
General Setup ->System ->Password Settings
To change password, please go to “System Configuration” -> “Password Settings” menu.
5. System Configuration
AirLive AC-1200 User’s Manual
70
5.1.4 System Management
General Setup ->System -> Remote Management
In this page, administrator can change the management parameters and disable/enable
management interface.
Host Address: To set up the IP address which allow the user to management
AC-1200R via Internet
HTTP Port No: The port number for remote management.The default port for
HTTP is Port 8080, you can change the value here. Please donot set the 80
Enable: You can enable or disable HTTP service from WAN side
Response to WAN ping: You can disable or enable whether AC-1200R will
response to PING command.
5. System Configuration
71 AirLive AC-1200R User’s Manual
5.1.5 WAN
General Setup -> WAN
If AC-1200R is working in router mode, WAN setting is appear. When can setup the WAN in
operation -> setup or in here
5.1.6 2.4G Wireless
AC-1200R supports multiple operations for 2.4G and 5G radio and each radio can work in
difference mode. You can setup the operation mode, channel , SSID in operation setup or
you can setup in here if you want to have specific operation in each mode. When you setup
in Operation Mode, the parameter in here will change as well
5.1.6.1 Basic Setting
This page allows you to define ESSID, and Channel for the wireless connection. These
parameters are used for the wireless stations to connect to the Access Point. You also can
figure out who are connecting to the AC-1200R via 2.4G band
5.1.6.2 Guess
This page allows you to define the ESSID (Guess) and wireless security. These parameters
are used by wireless stations to connect to this router. Turn on WEP or WPA by using
encryption keys in order to prevent unauthorized access to your wireless network.
The wireless stations which connect to the Guess SSID cannot access AC-1200R and it
can have difference wireless encryption from the main SSID
5. System Configuration
AirLive AC-1200 User’s Manual
72
5. System Configuration
73 AirLive AC-1200R User’s Manual
5.1.6.3 Advance Setting
This page is to set the advance setting for wireless parameter. You can refer the chapter
4.2.8 for the detail.
5. System Configuration
AirLive AC-1200 User’s Manual
74
5.1.6.4 Security Setting
This page allows you setup the wireless security. Turn on WEP or WPA by using Encryption
Keys could prevent any unauthorized access to your wireless network.
You can refer the 4.2.7 for detail setting, each radio has its own security setting.
5. System Configuration
75 AirLive AC-1200R User’s Manual
5.1.6.5 Access Control
For security reason, the Wireless Router features MAC Address Filtering that only allows
authorized MAC Addresses associating to the Router via 2.4G radio.
5. System Configuration
AirLive AC-1200 User’s Manual
76
5.1.6.6 WPS
This page allows you to change the setting for WPS (Wi-Fi Protected Setup). WPS can help
your wireless client automatically connect to the Wireless Router.
5. System Configuration
77 AirLive AC-1200R User’s Manual
5.1.7 5G Wireless
AC-1200R supports multiple operations for 2.4G and 5G radio and each radio can work in
difference mode. You can setup the operation mode, channel, SSID in Operation Mode or
you can setup in here if you want to have specific operation in each mode. When you setup
in Operation Mode, the parameter in here will change as well
AC-1200R 2.4G/5G can work individually. You can refer the 5.1.6 for the detail setting.
5. System Configuration
AirLive AC-1200 User’s Manual
78
5.1.8 QoS
QoS (Quality of Service) refers to the capability of a network to provide better service to
selected network traffic. The primary goal of QoS is to provide priority including dedicated
bandwidth, controlled jitter and latency (required by some real-time and interactive traffic),
and improved loss characteristics. Also important is making sure that providing priority for
one or more flows does not make other flows fail.
You can refer chapter 4.2.11 for the detail setting.
5. System Configuration
79 AirLive AC-1200R User’s Manual
5.1.9 NAT
NAT (Network Address Translation) allows multiple users at your local site to access the
Internet through a single Public IP Address or multiple Public IP Addresses. NAT provides
Firewall protection from hacker attacks and has the flexibility to allow you to map Private IP
Addresses to Public IP Addresses for key services such as the Web or FTP.
You can refer chapter 4.6.4 ,4.6.5, 4.6.6 for the Port Forwarding, Virtual Server, Special
applications.
5.1.9.1 UPNP
UPnP is more than just a simple extension of the Plug and Play peripheral model. It is
designed to support zero-configuration, "invisible" networking, and automatic discovery for
a breadth of device categories from a wide range of vendors. With UPnP, a device can
dynamically join a network, obtain an IP address, convey its capabilities, and learn about
the presence and capabilities of other devices-all automatically; truly enabling zero
configuration networks. Devices can subsequently communicate with each other directly;
thereby further enabling peer to peer networking.
Select Enable to enable the UPNP function
5. System Configuration
AirLive AC-1200 User’s Manual
80
5.1.9.2 ALG Setting
Some applications that need router's special support to make them work under the NAT.
You can select applications that you are using.
5.1.10 Firewall
AC-1200R Router provides extensive firewall protection by restricting connection
parameters, thus limiting the risk of hacker attack, and defending against a wide array of
common attacks. However, for applications that require unrestricted access to the Internet,
you can configure a specific client/server as a Demilitarized Zone (DMZ).
You can refer the chapter 4.6.4 and 4.6.7 for the DMZ and IP Filtering Setting
5. System Configuration
81 AirLive AC-1200R User’s Manual
5.1.10.1 URL Blocking
URL Blocking allow user to block access to certain Web sites from a particular PC by
entering either a full URL address or just a keyword of the Web site
5.1.10.2 DoS
AC-1200R can block common hacker attacks, including DoS, Discard Ping from WAN and
Port Scan.
6. Device Status & Tools
AirLive AC-1200 User’s Manual
82
6.1 Status
When you click on the “Status” on the top menu bar, the sub menu for device status will
appear.
6.1.1 Status
This page provides the following information about your Wireless Router:
Hardware/Firmware version, Serial Number, and its current operating status.
6.1.2 Internet Connection
This page displays the current internet connection status and related information.
6
6. Device Status & Tools
6. Device Status & Tools
83 AirLive AC-1200R User’s Manual
6.1.3 Device Status
This page shows the general information about AC-1200R such as , device IP/MAC
Wireless Encryption, SSID…etc. Below are some additional explanations on some status
information of this page:
6. Device Status & Tools
AirLive AC-1200 User’s Manual
84
6.1.4 System Log
The System Log displays the system activities, login, and system error report. If you need
to report a problem to Air Live, please be sure to send us the System Log information also.
6.1.5 Security Log
The Security Log displays any attempts that have been made to illegally gain access to
your network.
6. Device Status & Tools
85 AirLive AC-1200R User’s Manual
6.1.6 Active DHCP Client
This table shows the assigned IP address, MAC address and time expired for each DHCP
leased client.
6.1.7 Statistics
This page shows the packet counters for transmission and reception regarding to networks
including 2.4G/5G Wireless, LAN and WAN Port
6. Device Status & Tools
AirLive AC-1200 User’s Manual
86
6.1.8 Configuration Tools
Use the "Backup" tool to save the Wireless Router's current configurations to a file named
"config.bin". You can then use the "Restore" tool to restore the saved configuration to the
Wireless Router. Alternatively, you can use the "Restore to Factory Default" tool to force the
Wireless Router to perform System Reset and restore the original factory setting
6.1.9 Firmware Upgrade
This page allows you to upgrade the Wireless Router's system firmware. Enter the path and
name of the upgrade file and then click the APPLY button below. You will be prompted to
confirm the upgrade.
Do not power off the device while upgrading the firmware.
It is recommended that you do not upgrade your AC-1200R unless the
new firmware has new features you need or if it has a fix to a problem
that you’ve encountered.
6. Device Status & Tools
87 AirLive AC-1200R User’s Manual
6.1.10 Reset
In the event that the system stops responding correctly or stops functioning, you can
perform a Reboot. Your settings will not be changed. To perform the reboot,click on the
APPLY button below. You will be asked to confirm your decision.The Reboot will be
complete when the LED Power light stops blinking.
7. Frequent Asked Questions
AirLive AC-1200 User’s Manual
88
====================================================================
Question: I heard AC-1200R can limit the bandwidth of BitTorrent and eDonkey traffic.
But I don’t see the option on the Bandwidth Control.
Answer: The option to limit bandwidth by application or port is available only on WISP
and Router modes.
===================================================================
Question: When do I use Per-User Bandwidth Control by IP, MAC, or IP segment?
Answer: In general, IP address control limits the devices on the end node (i.e. PC and
WISP router). MAC address control can limit the traffic of a AP/CPE in
wireless client mode.
IP address: When you want to limit the bandwidth of a single notebook
computer, PC, or WISP router.
MAC address: When you want to limit the bandwidth of a remote
AP/CPE in Client mode. For example, another AC-1200R in client mode
IP Segment: When you want to limit the bandwidth of an entire IP range.
For example, all the PCs using the DHCP server to get IP addresses.
====================================================================
Question: I thought AC-1200R has PPPoE server function, where can I find it?
Answer: The AC-1200R PPPoE function is available only in “Dual Band Router Mode”.
The PPPoE function is inside the “Wireless Settings”->WAN Settings.
Please see graphics below:
7
7. Frequent Asked
Questions
7. Frequent Asked Questions
89 AirLive AC-1200R User’s Manual
====================================================================
8. Specifications
AirLive AC-1200 User’s Manual
90
The specification of AC-1200R is subject to change without notice. Please use the
information with caution.
Hardware
MedeaTek CPU
High power design, up to 23dBm with included antennas ( 20dBm in EU)
5 x 10/100/1000Mbps LAN Ports
2.4G/5G Dual Band Technology
MIMO Technology
8MB Flash, 32MB SDRAM
Antenna
2 x R-SMA antenna connectors
8
8. Specifications
8. Specifications
91 AirLive AC-1200R User’s Manual
Frequency Range
WLAN1(Radio 1)
802.11ac : 5.15 to 5.825 GHz
WLAN2 (Radio 2)
802.11b/g/n : 2.412 to 2.472 GHz
Frequency Band
5.15 to 5.25GHz: U-NII Low and ETSI Band1
5.25 to 5.35GHz: U-NII Mid and ETSI Band2
5.47 to 5.725GHz: U-NII World Wide and ETSI Band3
5.745 to 5.825GHz, U-NII Upper Band
Frequency Channel
WLAN1(Radio 1)
802.11ac
USA (FCC) : 12
Europe (ETSI) : 4
WLAN2(Radio 2)
802.11b/g
USA (FCC) : 11
Europe (ETSI) : 13
Power Supply
12V at 1.5A DC Power Adapter
8. Specifications
AirLive AC-1200 User’s Manual
92
Supported WLAN Mode
11ac mode
11 b/g/n
Output Power (without antennas)
2.4GHz
11b(11M): 16±1.5 dBm
11g(54M): 14±1.5 dBm
11n(20MHz, MCS7): 14±1.5 dBm
11n(40MHz, MCS7): 14±1.5 dBm
5GHz
11a(54M): 13±1.5 dBm
11n(20MHz, MCS7): 13±1.5 dBm
11n(40MHz, MCS7): 13±1.5 dBm
Receive Sensitivity
2.4GHz
11b(11M): -76±2dBm
11g(54M): -65±2dBm
11n(20MHz, MCS7):-64±2dBm
11n(40MHz, MCS7):-61±2dBm
5GHz
11a(54M): -65±2dBm
11n(20MHz, MCS7): -64±2dBm
11n(40MHz, MCS7): -61±2dBm
8. Specifications
93 AirLive AC-1200R User’s Manual
Software
Wi-Fi, WPA compatible interoperability
Support WDS Bridge Mode, Client Mode, AP Mode on interface under each predefined
operational mode
Client Isolation supported
5/10/20/40/80 MHz Variable Channel Width
Support adjustable output power
User Limitation
Multiple SSID, VLAN, QoS, WPA with PSK/TKIP/AES support ,WPA2 support
Radius Support
QoS
Bandwidth Control
Product Weight (g)
305 g
Product Size (L x W x H mm)
173 x 130 x 33 mm
9. Wireless Network Glossary
AirLive AC-1200 User’s Manual
94
The wireless network glossary contains explanation or information about common terms
used in wireless networking products. Some of information in this glossary might be
outdated, please use with caution.
802.11a
An IEEE specification for wireless networking that operates in the 5 GHz frequency range
(5.15 GHz to 5.850 GHz) with a maximum of 54 Mbps data transfer rate. The 5 GHz
frequency band is not as crowded as the 2.4 GHz band. In addition, the 802.11a have 12
non-overlapping channels, comparing to 802.11b/g's 3 non-overlapping channels. This
means the possibility to build larger non-interfering networks. However, the 802.11a deliver
shorter distance at the same output power when comparing to 802.11g.
802.3ad
802.3ad is an IEEE standard for bonding or aggregating multiple Ethernet ports into one
virtual port (also known as trunking) to increase the bandwidth.
802.3af
This is the PoE (Power over Ethernet) standard by IEEE committee. 802.3af uses 48V POE
standard that can deliver up to 100 meter distance over Ethernet cable.
9
9. Wireless Network
Glossary
9. Wireless Network Glossary
95 AirLive AC-1200R User’s Manual
802.11b
International standard for wireless networking that operates in the 2.4 GHz frequency band
(2.4 GHz to 2.4835 GHz) and provides a throughput up to 11 Mbps.
802.1d STP
Spanning Tree Protocol. It is an algorithm to prevent network from forming. The STP
protocol allows net work to provide a redundant link in the event of a link failure. It is advise
to turn on this option for multi-link bridge network.
802.11d
Also known as “Global Roaming”. 802.11d is a standard for use in countries where systems
using other standards in the 802.11 family are not allowed to operate.
802.11e
The IEEE QoS standard for prioritizing traffic of the VoIP and multimedia applications.
The WMM is based on a subset of the 802.11e.
802.11g
A standard provides a throughput up to 54 Mbps using OFDM technology. It also operates
in the 2.4 GHz frequency band as 802.11b. 802.11g devices are backward compatible with
802.11b devices.
802.11h
This IEEE standard define the TPC (transmission power control) and DFS(dynamic
frequency selection) required to operate WiFi devices in 5GHz for EU.
9. Wireless Network Glossary
AirLive AC-1200 User’s Manual
96
802.11i
The IEEE standard for wireless security. 802.11i standard includes TKIP, CCMP, and AES
encryption to improve wireless security. It is also known as WPA2.
802.1Q Tag VLAN
In 802.1Q VLAN, the VLAN information is written into the Ethernet packet itself. Each
packet carries a VLAN ID(called Tag) as it traveled across the network. Therefore, the
VLAN configuration can be configured across multiple switches. In 802.1Q spec, possible
4096 VLAN ID can be created. Although for some devices, they can only view in frames of
256 ID at a time.
802.1x
802.1x is a security standard for wired and wireless LANs. In the 802.1x parlance, there are
usually supplicants (client), authenticator (switch or AP), and authentication server (radius
server) in the network. When a supplicants request a service, the authenticator will pass the
request and wait for the authentication server to grant access and register accounting.
The 802.1x is the most widely used method of authentication by WISP.
Adhoc
A Peer-to-Peer wireless network. An Adhoc wireless network do not use wireless AP or
router as the central hub of the network. Instead, wireless client are connected directly to
each other. The disadvantage of Adhoc network is the lack of wired interface to Internet
connections. It is not recommended for network more than 2 nodes.
Access Point (AP)
The central hub of a wireless LAN network. Access Points have one or more Ethernet ports
that can connect devices (such as Internet connection) for sharing. Multi-function Access
Point can also function as an Ethernet client, wireless bridge, or repeat signals from other
AP. Access Points typically have more wireless functions comparing to wireless routers.
9. Wireless Network Glossary
97 AirLive AC-1200R User’s Manual
ACK Timeout
Acknowledgement Timeout Windows. When a packet is sent out from one wireless station
to the other, it will waits for an Acknowledgement frame from the remote station. The station
will only wait for a certain amount of time; this time is called the ACK timeout. If the ACK is
NOT received within that timeout period then the packet will be re-transmitted resulting in
reduced throughput. If the ACK setting is too high then throughput will be lost due to waiting
for the Ack Window to timeout on lost packets. If the ACK setting is too low then the ACK
window will have expired and the returning packet will be dropped, greatly lowering
throughput. By having the ability to adjust the ACK setting we can effectively optimize the
throughput over long distance links. This is especially true for 802.11a and 802.11g
networks. Setting the correct ACK timeout value needs to consider 3 factors: distance, AP
response time, and interference. The AC-1200R provides ACK adjustment capability in
form of either distance or direct input. When you enter the distance parameter, the
AC-1200R will automatically calculate the correct ACK timeout value.
Bandwidth Management
Bandwidth Management controls the transmission speed of a port, user, IP address, and
application. Router can use bandwidth control to limit the Internet connection speed of
individual IP or Application. It can also guarantee the speed of certain special application or
privileged IP address - a crucial feature of QoS (Quality of Service) function. The
AC-1200R’s features both “Per-user Bandwidth Control” and “Total Bandwidth Control”.
“Per-user Bandwidth Control” allow administrator to define the maximum bandwidth of each
user by IP, IP Group, or MAC address. Total Bandwidth defines the maximum bandwidth of
wireless or Ethernet interface.
Bootloader
Bootloader is the under layering program that will start at the power-up before the device
loads firmware. It is similar to BIOS on a personal computer. When a firmware crashed, you
might be able to recover your device from bootloader.
9. Wireless Network Glossary
AirLive AC-1200 User’s Manual
98
Bridge
A product that connects 2 different networks that uses the same protocol. Wireless bridges
are commonly used to link network across remote buildings. For wireless application, there
are 2 types of Bridges. WDS Bridge can be used in Point-to-Point or Point-to-Multipoint
topology. Bridge Infrastructure works with AP mode to form a star topology.
Cable and Connector Loss
During wireless design and deployment, it is important to factor in the cable and connector
loss. Cable and connector loss will reduce the output power and receiver sensitivity of the
radio at connector end. The longer the cable length is, the more the cable loss. Cable
loss should be subtracted from the total output power during distance calculation. For
example, if the cable and connector loss is 3dBm and the output power is 20dBm; the
output power at the cable end is only 17dBm.
Client
Client means a network device or utility that receives service from host or server. A client
device means end user device such as wireless cards or wireless CPE.
CPE Devices
CPE stands for Customer Premises Equipment. A CPE is a device installed on the end
user's side to receive network services. For example, on an ADSL network, the ADSL
modem/router on the subscriber's home is the CPE device. Wireless CPE means a
complete Wireless (usually an AP with built-in Antenna) that receive wireless broadband
access from the WISP. The opposite of CPE is CO.
CTS
Clear To Send. A signal sent by a device to indicate that it is ready to receive data.
9. Wireless Network Glossary
99 AirLive AC-1200R User’s Manual
DDNS
Dynamic Domain Name System. An algorithm that allows the use of dynamic IP address for
hosting Internet Server. A DDNS service provides each user account with a domain name.
A router with DDNS capability has a built-in DDNS client that updates the IP address
information to DDNS service provider whenever there is a change. Therefore, users can
build website or other Internet servers even if they don't have fixed IP connection.
DHCP
Dynamic Hosting Configuration Protocol. A protocol that enables a server to dynamically
assign IP addresses. When DHCP is used, whenever a computer logs onto the network, it
automatically gets an IP address assigned to it by DHCP server. A DHCP server can either
be a designated PC on the network or another network device, such as a router.
DMZ
Demilitarized Zone. When a router opens a DMZ port to an internal network device, it opens
all the TCP/UDP service ports to this particular device. The feature is used commonly for
setting up H.323 VoIP or Multi-Media servers.
DNS
A program that translates URLs to IP addresses by accessing a database maintained on a
collection of Internet servers.
Domain Name
The unique name that identifies an Internet site. Domain Names always have 2 or more
parts, separated by dots. In www.airlive.com, the "airlive.com" is the doman name.
9. Wireless Network Glossary
AirLive AC-1200 User’s Manual
100
DoS Attack
Denial of Service. A type of network attack that floods the network with useless traffic. Many
DoS attacks, such as the Ping of Death and Teardrop attacks, exploit limitations in the
TCP/IP protocols.
Encryption
Encoding data to prevent it from being read by unauthorized people. The common wireless
encryption schemes are WEP, WPA, and WPA2.
ESSID (SSID)
The identification name of an 802.11 wireless network. Since wireless network has no
physical boundary liked wired Ethernet network, wireless LAN needs an identifier to
distinguish one network from the other. Wireless clients must know the SSID in order to
associate with a WLAN network. Hide SSID feature disable SSID broadcast, so users must
know the correct SSID in order to join a wireless network.
Firewall
A system that secures a network and prevents access by unauthorized users. Firewalls can
be software, router, or gateway. Firewalls can prevent unrestricted access into a network,
as well as restricting data from flowing out of a network.
Firmware
The program that runs inside embedded device such as router or AP. Many network
devices are firmware upgradeable through web interface or utility program.
9. Wireless Network Glossary
101 AirLive AC-1200R User’s Manual
FTP
File Transfer Protocol. A standard protocol for sending files between computers over a
TCP/IP network and the Internet.
Fragment Threshold
Frame Size larger than this will be divided into smaller fragment. If there are interferences
in your area, lower this value can improve the performance. If there are not, keep this
parameter at higher value. The default size is 2346. You can try 1500, 1000, or 500 when
there are interference around your network.
Full Duplex
The ability of a networking device to receive and transmit data simultaneously. In wireless
environment, this is usually done with 2 or more radios doing load balancing.
Gateway
In the global Internet network, the gateways are core routers that connect networks in
different IP subnet together. In a LAN environment with an IP sharing router, the gateway is
the router. In an office environment, gateway typically is a multi-function device that
integrates NAT, firewall, bandwidth management, and other security functions.
Hotspot
A place where you can access Wi-Fi service. The term hotspot has two meanings in
wireless deployment. One is the wireless infrastructure deployment; the other is the Internet
access billing system. In a hotspot system, a service provider typically need an
authentication and account system for billing purposes, and a wireless AP network to
provide access for customers.
9. Wireless Network Glossary
AirLive AC-1200 User’s Manual
102
IGMP Snooping
Internet Group Management Protocol (IGMP) is a Layer 3 protocol to report IP multicast
memberships to neighboring multicast switches and routers. IGMP snooping is a feature
that allows an Ethernet switch to "listen in" on the IGMP conversation between hosts and
routers. A switch support IGMP snooping has the possibility to avoid multicast traffic being
treated as broadcast traffic; therefore, reducing the overall traffic on the network.
Infrastructure Mode
A wireless network that is built around one or more access points to provide wireless clients
access to wired LAN / Internet service. The opposite of Infrastructure mode is Adhoc mode.
IP address
IP (Internet Protocol) is a layer-3 network protocol that is the basis of all Internet
communication. An IP address is 32-bit number that identifies each sender or receiver of
information that is sent across the Internet. An IP address has two parts: an identifier of a
particular network on the Internet and an identifier of the particular device (which can be a
server or a workstation) within that network. The new IPv6 specification supports 128-bit IP
address format.
IPsec
IP Security. A set of protocols developed by the IETF to support secure exchange of
packets at the IP layer. IPsec has been deployed widely to implement Virtual Private
Networks (VPNs). IPsec supports two encryption modes: Transport and Tunnel.
Transport mode encrypts only the data of each packet, but leaves the header untouched.
The more secure Tunnel mode encrypts both the header and the payload. On the receiving
side, an IPSec-compliant device decrypts each packet.
9. Wireless Network Glossary
103 AirLive AC-1200R User’s Manual
LACP (802.3ad) Trunking
The 802.3ad Link Aggregation standard defines how to combine the several Ethernet ports
into one high-bandwidth port to increase the transmission speed. It is also known as port
trunking. Both devices must set the trunking feature to work.
MAC
Media Access Control. MAC address provides layer-2 identification for Networking Devices.
Each Ethernet device has its own unique address. The first 6 digits are unique for each
manufacturer. When a network device have MAC access control feature, only the devices
with the approved MAC address can connect with the network.
Mbps
Megabits per Second. One million bits per second; a unit of measurement for data
transmission
MESH
Mesh is an outdoor wireless technology that uses Spanning Tree Protocol (STP) and
Wireless Distribution system to achieve self-forming, self-healing, and self-configuring
outdoor network. MESH network are able to take the shortest path to a destination that
does not have to be in the line of site.
MIMO
Multi In Multi Out. A Smart Antenna technology designed to increase the coverage and
performance of a WLAN network. In a MIMO device, 2 or more antennas are used to
increase the receiver sensitivity and to focus available power at intended Rx.
NAT
Network Address Translation. A network algorithm used by Routers to enables several PCs
to share single IP address provided by the ISP. The IP that a router gets from the ISP side
is called Real IP, the IP assigned to PC under the NAT environment is called Private IP.
9. Wireless Network Glossary
AirLive AC-1200 User’s Manual
104
Node
A network connection end point, typically a computer.
Packet
A unit of data sent over a network.
Passphrase
Used much like a password, a passphrase simplifies the WEP encryption process by
automatically generating the WEP encryption keys for the company products.
POE
Power over Ethernet. A standard to deliver both power and data through one single
Ethernet cable (UTP/STP). It allows network device to be installed far away from power
ource. A POE system typically compose of 2 main component: DC Injector (Base Unit) and
Splitter(Terminal Unit). The DC injector combines the power and data, and the splitter
separates the data and power back. A PoE Access Point or CPE has the splitter built-in to
the device. The IEEE 802.3af is a POE spec that uses 48 volt to deliver power up to 100
meter distance.
Port
This word has 2 different meaning for networking.
The hardware connection point on a computer or networking device used for plugging
in a cable or an adapter.
The virtual connection point through which a computer uses a specific application on a
server.
9. Wireless Network Glossary
105 AirLive AC-1200R User’s Manual
PPPoE
Point-to- Point Protocol over Ethernet. PPPoE relies on two widely accepted standards:
PPP and Ethernet. PPPoE is a specification for connecting the users on an Ethernet to the
Internet through a common broadband medium, such as a single DSL line, wireless device
or cable modem.
PPTP
Point-to-Point Tunneling Protocol: A VPN protocol developed by PPTP Forum. With PPTP,
users can dial in to their corporate network via the Internet. If users require data encryption
when using the Windows PPTP client, the remote VPN server must support MPPE
(Microsoft Point-To-Point Encryption Protocol) encryption. PPTP is also used by some ISP
for user authentication, particularly when pairing with legacy Alcatel / Thomson ADSL
modem.
Preamble Type
Preamble are sent with each wireless packet transmit for transmission status. Use the long
preamble type for better compatibility. Use the short preamble type for better performance
Rate Control
Ethernet switches' function to control the upstream and downstream speed of an individual
port. Rate Control management uses "Flow Control" to limit the speed of a port. Therefore,
the Ethernet adapter must also have the flow control enabled. One way to force the
adapter's flow control on is to set a port to half-duplex mode.
RADIUS
Remote Authentication Dial-In User Service. An authentication and accounting system
used by many Internet Service Providers (ISPs). When you dial in to the ISP, you must
enter your username and password. This information is passed to a RADIUS server, which
checks that the information is correct, and then authorizes access to the ISP system.
Radius typically uses port 1812 and port 1813 for authentication and accounting port.
Though not an official standard, the RADIUS specification is maintained by a working group
of the IETF.
9. Wireless Network Glossary
AirLive AC-1200 User’s Manual
106
Receiver Sensitivity
Receiver sensitivity means how sensitive is the radio for receiving signal. In general; the
slower the transmission speed, the more sensitive the radio is. The unit for Receiver
Sensitivity is in dB; the lower the absolute value is, the higher the signal strength. For
example, -50dB is higher than -80dB.
RJ-45
Standard connectors for Twisted Pair copper cable used in Ethernet networks. Although
they look similar to standard RJ-11 telephone connectors, RJ-45 connectors can have up to
eight wires, whereas telephone connectors have only four.
Router
An IP sharing router is a device that allows multiple PCs to share one single broadband
connection using NAT technology. A wireless router is a device that combines the functions
of wireless Access Point and the IP sharing router.
RSSI
Receiver Sensitivity Index. RSSI is a value to show the Receiver Sensitivity of the remote
wireless device. In general, remote APs with stronger signal will display higher RSSI values.
For RSSI value, the smaller the absolute value is, the stronger the signal. For example,
“-50db” has stronger signal than “-80dB”. For outdoor connection, signal stronger than
-60dB is considered as a good connection.
RTS
Request To Send. A packet sent when a computer has data to transmit. The computer will
wait for a CTS (Clear To Send) message before sending data.
9. Wireless Network Glossary
107 AirLive AC-1200R User’s Manual
RTS Threshold
RTS (Request to Send). The RTS/CTS(clear to send) packet will be send before a frame if
the packet frame is larger than this value. Lower this value can improve the performance if
there are many clients in your network. You can try 1500, 1000 or 500 when there are many
clients in your AP’s network.
SNMP
Simple Network Management Protocol. A set of protocols for managing complex networks.
The SNMP network contains 3 key elements: managed devices, agents, and
network-management systems (NMSs). Managed devices are network devices that content
SNMP agents. SNMP agents are programs that reside SNMP capable device's firmware to
provide SNMP configuration service. The NMS typically is a PC based software such as HP
Openview that can view and manage SNMP network device remotely.
SSH
Developed by SSH Communications Security Ltd., Secure Shell is a program to log into
another computer over a network, to execute commands in a remote machine, and to move
files from one machine to another. It provides strong authentication and secure
communications over insecure channels. It is a replacement for rlogin, rsh, rcp, and rdist.
SSL
Secure Sockets Layer. It is a popular encryption scheme used by many online retail and
banking sites to protect the financial integrity of transactions. When an SSL session begins,
the server sends its public key to the browser. The browser then sends a randomly
generated secret key back to the server in order to have a secret key exchange for that
session. SSL VPN is also known as Web VPN. The HTTPS and SSH management
interface use SSL for data encryption.
9. Wireless Network Glossary
AirLive AC-1200 User’s Manual
108
Subnet Mask
An address code mask that determines the size of the network. An IP subnet are
determined by performing a BIT-wise AND operation between the IP address and the
subnet mask. By changing the subnet mask, you can change the scope and size of a
network.
Subnetwork or Subnet
Found in larger networks, these smaller networks are used to simplify addressing between
numerous computers. Subnets connect to the central network through a router, hub or
gateway. Each individual wireless LAN will probably use the same subnet for all the local
computers it talks to.
Super A
Super A is an Atheros proprietary turbo mode to increase speed over standard 802.11a
mode. It adds Bursting and Compression to increase the speed. If you live in countries that
prohibit the channel binding technology (i.e. Europe), you should choose “Super-A without
Turbo) if you need more speed than 11a mode
TCP
A layer-4 protocol used along with the IP to send data between computers over the Internet.
While IP takes care of handling the actual delivery of the data, TCP takes care of keeping
track of the packets that a message is divided into for efficient routing through the Internet.
Turbo A
Turbo A is an Atheros proprietary turbo mode to increase speed over standard 802.11a
mode. It uses channel binding technology to increase speed. There are 2 types of Turbo A
modes: Dynamic Turbo and Static Turbo. In Dynamic Turbo, the channel binding will be
used only if necessary. In Static Turbo, the channel binding is always on. This protocol may
be combined with Super-A model to increase the performance even more. The used of
channel binding might be prohibited in EU countries.
9. Wireless Network Glossary
109 AirLive AC-1200R User’s Manual
TX Output Power
Transmit Output Power. The TX output power means the transmission output power of the
radio. Normally, the TX output power level limit for 2.4GHz 11g/b is 20dBm at the antenna
end. The output power limit for 5GHz 802.11a is 30dBm at the antenna end.
UDP
User Datagram Protocol. A layer-4 network protocol for transmitting data that does not
require acknowledgement from the recipient of the data.
Upgrade
To replace existing software or firmware with a newer version.
Upload
To send a file to the Internet or network device.
URL
Uniform Resource Locator. The address of a file located on the Internet.
VPN
Virtual Private Network. A type of technology designed to increase the security of
information transferred over the Internet. VPN creates a private encrypted tunnel from the
end user's computer, through the local wireless network, through the Internet, all the way to
the corporate network.
9. Wireless Network Glossary
AirLive AC-1200 User’s Manual
110
Walled Garden
On the Internet, a walled garden refers to a browsing environment that controls the
information and Web sites the user is able to access. This is a popular method used by
ISPs in order to keep the user navigating only specific areas of the Web
WAN
Wide Area Network. A communication system of connecting PCs and other computing
devices across a large local, regional, national or international geographic area. A WAN
port on the network device means the port (or wireless connection) that is connected to the
Internet side of the network topology.
WEP
Wired Equivalent Privacy. A wireless encryption protocol. WEP is available in 40-bit (64-bit),
108-bit (128-bit) or 152-bit (Atheros proprietary) encryption modes.
Wi-Fi
Wireless Fidelity. An interoperability certification for wireless local area network (LAN)
products based on the IEEE 802.11 standards. The governing body for Wi-Fi is called
Wi-Fi Alliance (also known as WECA).
WiMAX
Worldwide Interoperability for Microwave Access. A Wireless Metropolitan Network
technology that complies with IEEE 802.16 and ETSI Hiperman standards. The orginal
802.16 standard call for operating frequency of 10 to 66Ghz spectrum. The 802.16a
amendment extends the original standard into spectrum between 2 and 11 Ghz. 802.16d
increase data rates to between 40 and 70 Mbps/s and add support for MIMO antennas,
QoS, and multiple polling technologies. 802.16e adds mobility features, narrower
bandwidth (a max of 5 mhz), slower speed and smaller antennas. Mobility is allowed up to
40 mph.
9. Wireless Network Glossary
111 AirLive AC-1200R User’s Manual
WDS
Wireless Distribution System. WDS defines how multiple wireless Access Point or Wireless
Router can connect together to form one single wireless network without using wired
uplinks. WDS associate each other by MAC address, each device
WLAN
Wireless Local Area Network. A type of local-area network that uses high-frequency radio
waves rather than wires to communicate between nodes. The most popular standard for
WLAN is the 802.11 standards.
WMM
Wi-Fi Multimedia (WMM) is a standard to prioritize traffic for multimedia applications. The
WMM prioritize traffic\ on Voice-over-IP (VoIP), audio, video, and streaming media as well
as traditional IP data over the AP.
WMS
Wireless Management System. An utility program to manage multiple wireless AP/Bridges.
WPA
Wi-Fi Protected Access. It is an encryption standard proposed by WiFi for advance
protection by utilizing a password key (TKIP) or certificate. It is more secure than WEP
encryption. The WPA-PSK utilizes pre-share key for encryption/authentication.
WPA2
Wi-Fi Protected Access 2. WPA2 is also known as 802.11i. It improves on the WPA security
with CCMP and AES encryption. The WPA2 is backward compatible with WPA.
WPA2-PSK utilizes pre-share key for encryption/authentication.