OvisLink NPLUG Wireless b/g/n Power Adapter Access Point User Manual N Plug

OvisLink Corp. Wireless b/g/n Power Adapter Access Point N Plug

User Manual

1 N.Plug Wireless b/g/n Power Adapter Access Point User’s Manual
Copyright and Disclaimer AirLive N.Plug User’s Manual i Copyright & Disclaimer No part of this publication may be reproduced in any form or by any means, whether electronic, mechanical, photocopying, or recording without the written consent of OvisLink Corp. OvisLink Corp. has made the best effort to ensure the accuracy of the information in this user’s guide. However, we are not liable for the inaccuracies or errors in this guide. Please use with caution. All information is subject to change without notice All Trademarks are properties of their respective holders.
Copyright and Disclaimer AirLive N.Plug User’s Manual iiFCC Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: z Reorient or relocate the receiving antenna. z Increase the separation between the equipment and receiver. z Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. z Consult the dealer or an experienced radio/TV technician for help. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT NOTE FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. NOTICE: the domain name of our e-mail address is being shifted from adt.com.tw to tw.bureauveritas.com. The old e-mail address is still valid till mid-2010. Please modify your address book to keep contact information correct and up-to-date.
Table of Contents AirLive N.Plug User’s Manual iiiTable of Contents 1. Introduction................................................................................................1 1.1 Overview..............................................................................................1 1.2 Firmware Upgrade and Tech Support ..................................................1 1.3 Product Features .................................................................................2 1.4 Physical Details....................................................................................3 1.4.1 Status LED/WPS .........................................................................................3 1.4.2 Upper Switch ...............................................................................................5 1.4.3 Bottom View ................................................................................................6 2. Operation Modes........................................................................................7 2.1 Router Mode ........................................................................................7 2.2 Access Point Mode ..............................................................................8 2.3 Repeater Mode ....................................................................................8 2.3.1 Repeater Mode (Default Mode) ...................................................................8 2.3.2 Repeating Router ........................................................................................9 2.3.3 Client Mode ...............................................................................................10 3. Installation................................................................................................12 3.1 Hardware Connection ........................................................................12 3.1.1 AP/Router Mode .........................................................................................12 3.1.2 Repeater Mode...........................................................................................12 3.2 Login ..................................................................................................13 3.3 Common Connection Types...............................................................16 3.3.1 Cable Modems ...........................................................................................16 3.3.2 DSL Modems..............................................................................................16 3.3.3 Other Modems (e.g. Broadband Wireless) .................................................17 4. Web Configuration...................................................................................18 4.1 Setup Wizard .....................................................................................19 4.1.1 Router Mode..............................................................................................19 4.1.2 Repeater Mode...........................................................................................21 4.1.3 AP Mode.....................................................................................................24 4.2 Wireless ............................................................................................25 4.2.1 Basic Settings.............................................................................................25 4.2.2 Advanced Settings......................................................................................34 4.2.3 Security ......................................................................................................36 4.2.4 Access Control ...........................................................................................38 4.2.5 WDS Settings .............................................................................................39
Table of Contents AirLive N.Plug User’s Manual iv4.2.6 Site Survey .................................................................................................43 4.2.7 WPS ...........................................................................................................44 4.2.8 Schedule ....................................................................................................45 4.3 Internet Setting .................................................................................46 4.3.1 WAN Interface ............................................................................................46 4.3.2 Port Filtering ...............................................................................................52 4.3.3 IP Filtering ..................................................................................................53 4.3.4 Port Forwarding ..........................................................................................54 4.3.5 URL Filtering...............................................................................................55 4.3.6 DMZ............................................................................................................56 4.3.7 DDNS .........................................................................................................57 4.3.8 Router Setup ..............................................................................................58 4.4 System..............................................................................................60 4.4.1 LAN Interface..............................................................................................60 4.4.2 Time Zone Setting ......................................................................................63 4.4.3 Denial-of-Service ........................................................................................64 4.4.4 Upgrade Firmware......................................................................................65 4.4.5 Save/Reload Setting...................................................................................65 4.4.6 Password....................................................................................................66 4.4.7 QoS ............................................................................................................67 4.5 Ststus ................................................................................................69 4.5.1 Status .........................................................................................................69 4.5.2 Statistics .....................................................................................................70 4.5.3 Log .............................................................................................................71 4.6 Reboot ..............................................................................................71 5. PC Configuration .....................................................................................72 5.1 Overview............................................................................................72 5.2 Windows Clients ................................................................................72 5.2.1 TCP/IP Settings – Overview ......................................................................72 5.2.2 Checking TCP/IP Settings - Windows 2000...............................................73 5.2.3 Checking TCP/IP Settings - Windows XP...................................................75 5.2.4 Checking TCP/IP Settings - Windows Vista................................................77 5.2.5 Checking TCP/IP Settings - Windows 7......................................................79 5.2.6 Internet Access...........................................................................................81 5.2.7 Macintosh Clients .......................................................................................83 5.2.8 Linux Clients...............................................................................................83 5.2.9 Other Unix Systems....................................................................................84 5.2.10Wireless Station Configuration..................................................................84 Appendix A: Troubleshooting.................................................................85 Appendix B: About Wireless LANs.........................................................88
1. Introduction AirLive N.Plug User’s Manual 11 1. Introduction 1.1 Overview The AirLive N.Plug is a wireless B/G/N multi-mode (Repeater/AP/Router) network device with support of 3G USB dongle and xDSL WAN. The size and casing of the device are compact and well designed which is great for users want to travel light but desire for complete wireless function support as well. N.Plug in repeater mode is also great for users who are looking to extend their current wireless network but use as little configuration as possible. If not specify, “Wireless Router” means N.Plug in the following paragraph. 1.2 Firmware Upgrade and Tech Support If you encounter a technical issue that can not be resolved by information on this guide, we recommend that you visit our comprehensive website support at www.airlive.com. The tech support FAQ are frequently updated with latest information. In addition, you might find new firmwares that either increase software functions or provide bug fixes for N.Plug. You can reach our on-line support center at the following link: http://www.airlive.com/support/support_2.jsp Since 2009, AirLive has added the “Newsletter Instant Support System” on our website. AirLive Newsletter subscribers receives instant email notifications when there are new download or tech support FAQ updates for their subscribed airlive models. To become an AirLive newsletter member, please visit: http://www.airlive.com/member/member_3.jsp
1. Introduction AirLive N.Plug User’s Manual 2 Figure 1.1: AirLive Newsletter Support System 1.3 Product Features  Repeater, AP, Router all-in-one compact design!  Extend your coverage distance of current wireless network!  Configuration free with WPS  Easy-installation!! Plug directly onto electric socket/outlet!  IEEE 802.11 B/G/N standard  Support 3G/3.5G USB dongle and xDSL WAN
1. Introduction AirLive N.Plug User’s Manual 31.4 Physical Details 1.4.1 Status LED/WPS
1. Introduction AirLive N.Plug User’s Manual 4 WPS button Press the physical WPS button on the Wireless Router once, or go to enable the WPS function via web configuration (Go to Wireless > WPS page), then the LED will start to flash. Please make a connection with other WPS supported device within 2 minutes. LED Behavior LED Printed Color Behavior Indication Off Power off On Power on POWER PWR Green Flashing System is resetting. Flashing Try to surf Internet Off Surfing Internet is successfully Internet Internet Yellow On Fail to surf Internet Off WLAN function off On WLAN link / active Wireless LAN WLAN Yellow Flashing WLAN traffic transmitting Off No Ethernet cable connecting On Ethernet cable connected WAN/LAN 1 port (Ethernet) WAN/LAN1 Green Flashing Receiving/ sending data Off No Ethernet cable connecting On Ethernet cable connected LAN 2 Port (Ethernet) LAN2 Green Flashing Receiving/ sending data
1. Introduction AirLive N.Plug User’s Manual 51.4.2 Upper Switch Hardware Mode Selector and USB port AP In order switch to AP mode, User need to MANUALLY flick the hardware switch to the line labeled AP. The device will reboot which takes about 45 seconds. After the device has fully started, it will automatically into the selected AP mode. Repeater This is the DEFAULT mode when release from factory. In order switch to Repeater mode, User need to MANUALLY flick the hardware switch to the line labeled Repeater. The device will reboot which takes about 45 seconds. After the device has fully started, it will automatically into the selected Repeater mode. Router In order switch to Router mode, User need to MANUALLY flick the hardware switch to the line labeled Router. The device will reboot which takes about 45 seconds. After the device has fully started, it will automatically into the selected Router mode. USB Port 2.0 USB port which provide access for 3G/3.5G USB dongle. For the compatibly 3G/3.5G dongle support list, please refer to Appendix section.
1. Introduction AirLive N.Plug User’s Manual 61.4.3 Bottom View Hardware Radio switch, WAN/LAN1 port, LAN2 port and R-SMA Antenna Connector WAN/LAN1 port (Ethernet) When the mode sets to AP mode and user can use standard LAN cable (RJ-45 connector) to connect his/her PC with this port, it will automatically function as an "Uplink" port When the mode sets to Router mode, connect the ADSL or Cable Modem here with RJ45 cable. If your modem came with a cable, use the supplied cable, otherwise, use a standard LAN cable (RJ45 connectors). When the mode sets to Repeater (Repeating Router), it will serve as standard LAN port will shares the internet connection from Wireless.LAN2 port (Ethernet) When the mode sets to Router mode and user can use standard LAN cable (RJ-45 connector) to connect his/her PC with this port, it will enable the device to share the internet connection from WAN/LAN1. Power ON/OFF switch User will able to turn on and off the N.Plug with this hardware switch.R-SMA Antenna Connector User will connect the provided R-SMA antenna by screw the antenna in a clockwise direction to the bottom panel of the device.
2. Operation Modes AirLive N.Plug User’s Manual 72 2. Operation Modes This device provides operational applications with Router, AP and Repeater modes, which are mutually exclusive. This device is shipped with configuration that is functional right out of the box. If you want to change the settings in order to perform more advanced configuration or even change the mode of operation, you can manually switch to the mode you desire by the manufacturer as described in the following sections. The default setting mode is Repeater mode. Switch Bar 2.1 Router Mode When set to Router mode, ensure you are using the wireless LAN interface, connect the Wireless Router with computer via radio frequency. In this mode, the device is supposed to connect to internet via ADSL/Cable Modem or with 3G/3.5G USB dongle. Connect the ADSL modem to the Ethernet port of the Wireless Router by Ethernet cable or Connect the 3G/3.5G USB dongle at the USB 2.0 Port. After connected successfully, user can login the web page of the Wireless Router to set up the Internet connection by using PPPoE, DHCP client, PPTP client , L2TP client or static IP.
2. Operation Modes AirLive N.Plug User’s Manual 82.2 Access Point Mode When acting as an Access Point (AP), this device connects all the stations (PC/notebook with wireless network adapter) to a wireless network. 2.3 Repeater Mode There are three selectable sub modes under Repeater. 2.3.1 Repeater Mode (Default Mode) If the sub mode sets to Repeater (Universal Repeater) mode, it can also extend the wireless coverage of another wireless AP or router. But the universal repeater does not require the remote device to have WDS function. Therefore, it can work with almost any wireless device. Note: When you are using the universal repeater mode, please make sure the remote AP/Router‘s WDS function is turned off.
2. Operation Modes AirLive N.Plug User’s Manual 92.3.2 Repeating Router For entering Repeating Router Mode, user needs to set the hardware switch to Repeater first. Then user can access to the web user interface of N.Plug, either use the Wizard function or just go to “Wireless Æ Basic” for selecting the Repeating Mode via the drop down box. If set to Repeater (Repeating Router) mode, In Repeating Router mode, the AP will behave just the same as the Client mode for wireless function. However, Router functions are added between the wireless WAN side and the Ethernet LAN side. Therefore, the ISP Subscriber can share the Repeating Router connection without the need for extra router
2. Operation Modes AirLive N.Plug User’s Manual 10 2.3.3 Client Mode For entering Client Mode, user needs to set the hardware switch to Repeater first. Then user can access to the web user interface of N.Plug, either use the Wizard function or just go to “Wireless Æ Basic” for selecting the Client Mode via the drop down box.
2. Operation Modes AirLive N.Plug User’s Manual 11 If set to Repeater (Client) mode, If set to Client mode, this device can work like a wireless station when it’s connected to a computer so that the computer can send packets from wired end to wireless interface.
3. Installation AirLive N.Plug User’s Manual 12 3.1 Hardware Connection 3.1.1 AP/Router Mode Connect via RJ-45 (Ethernet) cable 1. Set N.Plug in “AP mode” or “Router” Mode by using the hardware switch at the top of N.Plug 2. For Router mode, please connect Internet line to the WAN port. For 3G sharing, please connect your 3G USB dongle to the USB port. 3. Connect the LAN cable to the LAN port 4. If you have selected the AP mode, please make sure you have configured the PC’s IP address to the same subnet as the N.Plug. (for example, 192.168.1.50) 5. Open the web browser and enter N.Plug’s IP address (default 192.168.1.253). 6. Choose the “Wizard” to complete the setup. 3.1.2 Repeater Mode Configure one N.Plug as Repeater with WPS 1. Set N.Plug in “Repeater mode” by using the hardware switch at the top of N.Plug. 2. Plug-in N.Plug at the electrical outlet and wait about 2 minutes for devices to complete boot up. 3. Press the WPS push button for 5 seconds on the existing AP or Router. (If your AP/Router doesn’t have WPS Push Button. Please refer to its user’s guide on the CD for instructions). 4. Then within one minute, press the WPS push button on the N.Plug for 5 seconds until the WLAN LED is on and without flashing. 5. Wait for 2 minutes for the connection to establish between N.Plug and the AP/Router. 3 3 . Installation
3. Installation AirLive N.Plug User’s Manual 13 Configure one N.Plug as Repeater without WPS 1. Set N.Plug in “Repeater mode” by using the hardware switch at the top of N.Plug. 2. Plug-in N.Plug at the electrical outlet and wait about 2 minutes for devices to complete boot up. 3. Access WEB UI of N.Plug by enter http://192.168.1.253 in the URL box of Web Browser (IE/Firefox/Safari) 4. Enter UserID/Password as admin/airlive 5. After Logged in, click at Wizard at top panel of the page. 6. Click at the Site survey button 7. Choose the SSID of your Router/AP device, and press OK. 8. Press Next Button 9. Select corresponded Encryption of your Router/AP device 10. Select the Pre-Shared Key format of your Router/AP device 11. Enter Pre-Share Key 12. Press Finish and wait for N.Plug to reboot 13. Wait for 2 minutes for the connection to establish between N.Plug and the Router/AP. 3.2 Login Step1. Make sure the connection between your computer and Wireless Router setup successfully. Step2. Start your Web Browser. Step3. In the Address box, enter the IP address of the Wireless Router, as in this example, which uses the Wireless Router's default IP address: http://192.168.1.253.
3. Installation AirLive N.Plug User’s Manual 14Step4. After connected successfully, the following screen will show up. Simply enter the username “admin” and password “airlive” to login (case-sensitive). After login successfully, please click the Setup Wizard item that provides a primary configuration of this device. You may enter each screen to change the default settings step by step.
3. Installation AirLive N.Plug User’s Manual 15If you cannot connect... If the Wireless Router does not respond, please check following: Step1. The Wireless Router is properly installed and connection with computer is OK, and it is already powered ON. You can test the connection by using the "Ping" command: Step2. Please go to Start>Run…> Enter “cmd” command in the column to open the MS-DOS window. Step3. Enter the command: ping 192.168.1.253 Step4. If no response is received, either the connection is not working, or your PC's IP address is not compatible with the Wireless Router's IP address. (See next item.) Step5. If your PC is using a fixed IP address, its IP address must be within the range 192.168.1.1 to 192.168.1.252 to be compatible with the Wireless Router's default IP Address of 192.168.1.253. Also, the Network Mask must be set to 255.255.255.0. See Chapter 4 - PC Configuration for details on checking your PC's TCP/IP settings. Step6. Ensure that your PC and the Wireless Router are on the same network segment. (If you don't have a router, this must be the case.) Step7. When set to AP/Client mode, ensure you are using the wired LAN interface, connect the computer by Ethernet cable to the Ethernet port of the Wireless Router. Step8. When set to Router mode, ensure you are using the wireless interface, connect the Wireless Router with computer via radio frequency. The Wireless interface can only be used if its configuration matches computer’s wireless settings.
3. Installation AirLive N.Plug User’s Manual 163.3 Common Connection Types 3.3.1 Cable Modems Type Details ISP Data required Dynamic IP Address Your IP Address is allocated automatically, when you connect to you ISP. Usually, none. However, some ISP's may require you to use a particular Hostname, Domain name, or MAC (physical) address. Static (Fixed) IP Address Your ISP allocates a permanent IP Address to you. IP Address allocated to you. Some ISP's may also require you to use a particular Hostname, Domain name, or MAC (physical) address. 3.3.2 DSL Modems Type Details ISP Data required Dynamic IP Address Your IP Address is allocated automatically, when you connect to you ISP. None. Static (Fixed) IP Address Your ISP allocates a permanent IP Address to you. IP Address allocated to you. PPPoE You connect to the ISP only when required. The IP address is usually allocated automatically. User name and password. PPTP Mainly used in Europe. You connect to the ISP only when required. The IP address is usually allocated automatically, but may be Static (Fixed). 1. PPTP Server IP Address. 2. User name and password. 3. IP Address allocated to you, if Static (Fixed).
3. Installation AirLive N.Plug User’s Manual 17L2TP Mainly used in Europe. You connect to the ISP only when required. The IP address is usually allocated automatically, but may be Static (Fixed). 1. L2TP Server IP Address. 2. User name and password. 3. IP Address allocated to you, if Static (Fixed). 3.3.3 Other Modems (e.g. Broadband Wireless) Type Details ISP Data required Dynamic IP Address Your IP Address is allocated automatically, when you connect to you ISP. None Static (Fixed) IP Address Your ISP allocates a permanent IP Address to you. IP Address allocated to you.
4. Web Configuration AirLive N.Plug User’s Manual 18 After login successfully, please click the Setup Wizard item that provides a primary configuration of this device. You may enter each screen to change the default settings step by step. 4 4. Web Configuration
4. Web Configuration AirLive N.Plug User’s Manual 194.1 Setup Wizard The setup wizard will guide you to configure access point for first time. Please follow the setup wizard step by step. 4.1.1 Router Mode Step 1- Wireless Setting User can set the SSID, wireless encryption in this page. SSID A SSID is referred to a network name because essentially it is a name that identifies a wireless network (case-sensitive). Encryption Key We have chose the WPS2-PSK encryption type for you. If you wish to change to other encryption type, please go to “Wireless Æ Basic Setting” for further configuration.
4. Web Configuration AirLive N.Plug User’s Manual 20 Step2- WAN Configuration You can select the WAN connection type in this page. N.Plug supports DHCP, Static IP, L2TP, PPTP, PPPoE, BigPond, and 3G. We will take the PPPoE as an example here.
4. Web Configuration AirLive N.Plug User’s Manual 21WAN Connection Type If the PPPoE be selected, user have to set up the user name and password according to the ISP that provided the related information. User Name: Enter the username that provide by your ISP provider. Maximum input is 32 alphanumeric characters (case sensitive). Password: Enter the password that provide by your ISP provider. Maximum input is 32 alphanumeric characters (case sensitive). User Name Enter the username that provide by your ISP provider. Maximum input is 32 alphanumeric characters (case-sensitive). Password Enter the password that provide by your ISP provider. Maximum input is 32 alphanumeric characters (case-sensitive). Step3- Finish and Reboot Once the configuration is done, please click on the Finish button for applying the setting. 4.1.2 Repeater Mode
4. Web Configuration AirLive N.Plug User’s Manual 22Step 1- Mode Selection and Site Survey User can further select one of the three sub mode in this page. There are three sub modes supported by N.Plug. We will take Repeater mode as an example here. Mode Selection Repeater: Using repeater mode, N.Plug can also extend the wireless coverage of another wireless AP or router. Repeating Router: In Repeating Router mode, the AP will behave just the same as the Client mode for wireless function. However, router functions are added between the wireless WAN side and the Ethernet LAN side. Therefore, the WISP subscriber can share the WISP connection without the need for extra router. Client: If set to Client (Infrastructure) mode, N.Plug can work like a wireless station when it’s connected to a computer so that the computer can send packets from wired end to wireless interface. Site Survey You can use this page to search the remote AP you wanted. After clicking on the Site Survey button, N.Plug will list all availability AP’s or Routers in range. Please select your desired AP and click.
4. Web Configuration AirLive N.Plug User’s Manual 23 Step 2- Set Encryption User can set the SSID manually and configure the encryption of the wireless connection here. Once the configuration is done, please click on the Finish button for applying the setting. .
4. Web Configuration AirLive N.Plug User’s Manual 244.1.3 AP Mode Step 1- Wireless Setting User can select the set the SSID, wireless encryption in this page. SSID A SSID is referred to a network name because essentially it is a name that identifies a wireless network (case-sensitive). Encryption Key We have chose the WPS2-PSK encryption type for you. If you wish to change to other encryption type, please go to “Wireless Æ Basic Setting” for further configuration. Step 2- Finish and Reboot Once the configuration is done, please click on the Finish button for applying the setting.
4. Web Configuration AirLive N.Plug User’s Manual 254.2 Wireless 4.2.1 Basic Settings 4.2.1.1 AP/Router Disable Wireless LAN Interface Check to disable the wireless function. If the wireless LAN interface be disabled, the WLAN LED on the top will be off. Band You can choose one mode of the following you need. The default is 2.4GHz (B+G+N) mode. 2.4GHz (B): 802.11b supported rate only. 2.4GHz (G): 802.11g supported rate only. 2.4GHz (N): 802.11n supported rate only. 2.4GHz (B+G): 802.11b supported rate and 802.11g supported rate. 2.4GHz (G+N): 802.11g supported rate and 802.11n supported rate.
4. Web Configuration AirLive N.Plug User’s Manual 262.4GHz (B+G+N): 802.11b, 802.11g and 802.11n supported rate. User can select WDS disable/ WDS enable/ WDS only from the pull-down list. WDS Network Name (SSID) A SSID is referred to a network name because essentially it is a name that identifies a wireless network(case-sensitive). Multiple APs This page shows and updates the wireless setting for multiple APs User can set up the multiple AP here. To enable one of the APs from 1~4, then setup the wireless settings from the pull-down list.Channel Width This function will be available under 2.4GHz (N), 2.4GHz (G+N), 2.4GHz (B+G+N) mode. Select 20MHz the channel number will be form 5~11 and auto; Select 20/40MHz channel width the channel number will be form 1~11 and auto. Default is 20/40MHz.Control Sideband This function will be available under 2.4GHz (N), 2.4GHz (G+N), 2.4GHz (B+G+N) mode. Select upper or lower form the pull-down list, default is upper. Channel Number The channel number base on the channel width you select. Broadcast SSID Enabled: This Wireless Router will show its network name(SSID) to stations. Disabled: This Wireless Router will hide the network name to stations. If stations want to connect to this Wireless Router, this Router’s network name(SSID) should be known in advance to make a connection. WMM The Wi-Fi Multiple Media function is available under 2.4GHz (B), 2.4GHz (G) and 2.4GHz (B+G) band, and it is disabled under 2.4GHz (N), 2.4GHz (G+N) and 2.4GHz (B+G+N) band.
4. Web Configuration AirLive N.Plug User’s Manual 27Data Rate There are several data rate that you can select from the pull-down menu. Associated Clients Click button to show all connected clients. 4.2.1.1 Repeater In Repeater Mode, there are three sub modes, Repeater, Repeating Router and Client mode. According to different sub mode selected, the web will be slightly different for user to do the proper setting. Because in the repeater mode, the wireless setting will be mostly the same the upstream Router or AP, if not necessary, we recommend you to use the site survey or WPS function for getting these values automatically.
4. Web Configuration AirLive N.Plug User’s Manual 28 4.2.1.1.1 Repeater Disable Wireless LAN Interface Check to disable the wireless function. If the wireless LAN interface be disabled, the WLAN LED on the top will be off. Band You can choose one mode of the following you need. The default is 2.4GHz (B+G+N) mode. 2.4GHz (B): 802.11b supported rate only. 2.4GHz (G): 802.11g supported rate only. 2.4GHz (N): 802.11n supported rate only. 2.4GHz (B+G): 802.11b supported rate and 802.11g supported rate. 2.4GHz (G+N): 802.11g supported rate and 802.11n supported rate. 2.4GHz (B+G+N): 802.11b, 802.11g and 802.11n supported
4. Web Configuration AirLive N.Plug User’s Manual 29rate. Local SSID A SSID is referred to a network name because essentially it is a name that identifies a wireless network(case-sensitive). Remote SSID In Repeater Mode, the remote SSID should be the same with the repeated Router or AP. Channel Width This function will be available under 2.4GHz (N), 2.4GHz (G+N), 2.4GHz (B+G+N) mode. Select 20MHz the channel number will be form 1~11 and auto; Select 20/40MHz channel width the channel number will be form 5~11 and auto. Default is 20/40MHz.Control Sideband This function will be available under 2.4GHz (N), 2.4GHz (G+N), 2.4GHz (B+G+N) mode. Select upper or lower form the pull-down list, default is upper. Channel Number The channel number will be set the same as remote Ap automatically. Broadcast SSID Enabled: This Wireless Router will show its network name(SSID) to stations. Disabled: This Wireless Router will hide the network name to stations. If stations want to connect to this Wireless Router, this Router’s network name(SSID) should be known in advance to make a connection. WMM The Wi-Fi Multiple Media function is available under 2.4GHz (B), 2.4GHz (G) and 2.4GHz (B+G) band, and it is disabled under 2.4GHz (N), 2.4GHz (G+N) and 2.4GHz (B+G+N) band. Data Rate There are several data rate that you can select from the pull-down menu. Associated Clients Click button to show all connected clients.
4. Web Configuration AirLive N.Plug User’s Manual 30 4.2.1.1.2 Repeating Router Disable Wireless LAN Interface Check to disable the wireless function. If the wireless LAN interface be disabled, the WLAN LED on the top will be off. Band You can choose one mode of the following you need. The default is 2.4GHz (B+G+N) mode. 2.4GHz (B): 802.11b supported rate only. 2.4GHz (G): 802.11g supported rate only. 2.4GHz (N): 802.11n supported rate only. 2.4GHz (B+G): 802.11b supported rate and 802.11g supported rate.
4. Web Configuration AirLive N.Plug User’s Manual 31 2.4GHz (G+N): 802.11g supported rate and 802.11n supported rate. 2.4GHz (B+G+N): 802.11b, 802.11g and 802.11n supported rate. Local SSID A SSID is referred to a network name because essentially it is a name that identifies a wireless network(case-sensitive). Remote SSID In Repeater Mode, the remote SSID should be the same with the repeated Router or AP. WAN Setting Click on this button for invoking the WAN configuration page. Channel Width This function will be available under 2.4GHz (N), 2.4GHz (G+N), 2.4GHz (B+G+N) mode. Select 20MHz the channel number will be form 5~11 and auto; Select 20/40MHz channel width the
4. Web Configuration AirLive N.Plug User’s Manual 32channel number will be form 1~11 and auto. Default is 20/40MHz.Control Sideband This function will be available under 2.4GHz (N), 2.4GHz (G+N), 2.4GHz (B+G+N) mode. Select upper or lower form the pull-down list, default is upper. Channel Number The channel number will be set the same as remote Ap automatically. Broadcast SSID Enabled: This Wireless Router will show its network name(SSID) to stations. Disabled: This Wireless Router will hide the network name to stations. If stations want to connect to this Wireless Router, this Router’s network name(SSID) should be known in advance to make a connection. WMM The Wi-Fi Multiple Media function is available under 2.4GHz (B), 2.4GHz (G) and 2.4GHz (B+G) band, and it is disabled under 2.4GHz (N), 2.4GHz (G+N) and 2.4GHz (B+G+N) band. Data Rate There are several data rate that you can select from the pull-down menu. Associated Clients Click button to show all connected clients.
4. Web Configuration AirLive N.Plug User’s Manual 33 4.2.1.1.3 Client Disable Wireless LAN Interface Check to disable the wireless function. If the wireless LAN interface be disabled, the WLAN LED on the top will be off. Band You can choose one mode of the following you need. The default is 2.4GHz (B+G+N) mode. 2.4GHz (B): 802.11b supported rate only. 2.4GHz (G): 802.11g supported rate only. 2.4GHz (N): 802.11n supported rate only. 2.4GHz (B+G): 802.11b supported rate and 802.11g supported rate. 2.4GHz (G+N): 802.11g supported rate and 802.11n supported rate. 2.4GHz (B+G+N): 802.11b, 802.11g and 802.11n supported rate. Remote SSID In Repeater Mode, the remote SSID should be the same with the repeated Router or AP.
4. Web Configuration AirLive N.Plug User’s Manual 34 Channel Width This function will be available under 2.4GHz (N), 2.4GHz (G+N), 2.4GHz (B+G+N) mode. Select 20MHz the channel number will be form 5~11 and auto; Select 20/40MHz channel width the channel number will be form 1~11 and auto. Default is 20/40MHz.Control Sideband This function will be available under 2.4GHz (N), 2.4GHz (G+N), 2.4GHz (B+G+N) mode. Select upper or lower form the pull-down list, default is upper. Channel Number The channel number will be set the same as remote Ap automatically. 4.2.2 Advanced Settings
4. Web Configuration AirLive N.Plug User’s Manual 35 Fragment Threshold Fragmentation mechanism is used for improving the efficiency when high traffic flows along in the wireless network. If the 802.11g MIMO Wireless Router often transmit large files in wireless network, you can enter new Fragment Threshold value to split the packet. The value can be set from 256 to 2346. The default value is 2346. RTS Threshold RTS Threshold is a mechanism implemented to prevent the “Hidden Node” problem. If the “Hidden Node” problem is an issue, please specify the packet size. The RTS mechanism will be activated if the data size exceeds the value you set. Warning: Enabling RTS Threshold will cause redundant network overhead that could negatively affect the throughput performance instead of providing a remedy. This value should remain at its default setting of 2347. Should you encounter inconsistent data flow, only minor modifications of this value are recommended. Beacon Interval Beacon Interval is the amount of time between beacon transmissions. Before a station enters power save mode, the station needs the beacon interval to know when to wake up to receive the beacon. Range 20-1024 ms, default is 100. Preamble Type A preamble is a signal used in wireless environment to synchronize the transmitting timing including Synchronization and Start frame delimiter. You can select Long or Short for the preamble type. IAPP Select Enabled or Disabled to execute this function. Protection Select Enabled or Disabled to execute the security function. Aggregation Select Enabled or Disabled to execute this function. Short GI Select Enabled or Disabled to execute this function. WLAN Partition Select Enabled or Disabled to execute this function. 20/40MHz Coexist Select Enabled or Disabled to execute this function. The default is enabled. RF Output Power Select the transmitting power rate 100%, 70%, 50%, 35%, 15%.
4. Web Configuration AirLive N.Plug User’s Manual 364.2.3 Security Encryption Select desired security type from the pull-down menu Disable, WEP, WPA, WPA2 and WPA2-Mixed. The default setting is Disable. It is strongly recommended to set up security mode (WEP, WPA, WPA2 and WPA2-Mixed) to prevent any unauthorized accessing. Note: WPA and WPA2 only support TKIP and AES as encryption method. Shared Key only supports WEP as encryption method. AUTO(Open/Shared) means AP can accept station connect to it using OPEN-WEP or SHARED-WEP WEP 802.1x Authentication: Check the box to enable the 802.1x authentication. Authentication: Select Open System, Shared Key or Auto. Key Length: select key length 64-bit or 128-bit. Key Format:
4. Web Configuration AirLive N.Plug User’s Manual 37 Hexadecimal (WEP 64-bit): 10 Hex characters (0~9, a~f). Hexadecimal (WEP 128-bit): 26 Hex characters (0~9, a~f). ASCII (WEP 64-bit): 5 ASCII characters (case-sensitive). ASCII (WEP 128-bit): 13 ASCII characters (case-sensitive). Encryption Key: Enter the key in the key setting field. 802.1x Authentication Key Length: select key length 64 Bits or 128 Bits. RADIUS Server IP Address: Enter the RADIUS Server’s IP Address provided by your ISP. RADIUS Server Port: Enter the RADIUS Server’s port number provided by your ISP. The default is 1812. RADIUS Server Password: Enter the password that the AP shares with the RADIUS Server. WPA/ WPA2/ WPA2-Mixed Personal (Pre-Shared Key) Authentication Mode: Select Enterprise (RADIUS) or Personal (Pre-Shared Key) mode. WPA Cipher Suite: Here supported AES only.
4. Web Configuration AirLive N.Plug 38WPA2 Cipher Suite: Here supported AES only. Pre-Shared Key Format: There are two formats for choice to set the Pre-shared key, Passphrase and Hex (64 characters). If Hex is selected, users will have to enter a 64 characters string. For easier configuration, the Passphrase (at least 8 characters) format is recommended. Pre-Shared Key : Pre-Shared Key serves as a password. Users may key in 8 to 63 characters string if you selected passphrase. Pre-shared key format to set the passwords or leave it blank, in which the 802.1x Authentication will be activated. Make sure the same password is used on client's end. Enterprise (RADIUS) RADIUS Server IP Address: Enter the RADIUS Server’s IP Address provided by your ISP. RADIUS Server Port: Enter the RADIUS Server’s port number provided by your ISP. The default is 1812. RADIUS Server Password: Enter the password that the AP shares with the RADIUS Server. User’s Manual 4.2.4 Access Control
4. Web Configuration AirLive N.Plug User’s Manual 39Wireless Access Control Mode Enable or Disable the Access Control function. User can use this function for restricting the wireless client connection. MAC Address Enter the MAC address (12 characters) of a station that is allowed to access this Wireless Router. The format of the address should be XXXXXXXXXXXX. Delete Selected Click Delete Selected to delete items which are selected. Delete All Click Delete All to delete all the items. Reset Click Reset to rest. Apply Change Click Apply Change for save the configuration. 4.2.5 WDS Settings Wireless Distribution System uses wireless media to communicate with other APs, like the Ethernet does. To do this, you must set these APs in the same channel and set MAC address of other APs which you want to communicate with in the table and then enable the WDS. 1. The APs must support WDS function. 2. The channel must be set to the same on the APs. 3. To set the same Wireless MAC address (BSSID) on the APs. 4. To set same security (WEP key) on the APs. Note: To setup WDS must use the same wireless products (the same model will be better); due to different wireless products might support different WDS settings. Thus, it is suggested that to use the same wireless products that support WDS function. Step1. Users would like to set up the WDS function, please go to Wireless Æ Basic
4. Web Configuration AirLive N.Plug User’s Manual 40Settings page to enable WDS function, and set the APs into the same Channel Number. After setting up, please click Apply Changes button to execute. Step2. Then go back to Wireless Æ WDS Settings page to enter the Wireless MAC address (please make sure the BSSID of the other WDS supported AP) 12 characters to each other to make the WDS connection. Please click Apply Changes button to execute.
4. Web Configuration AirLive N.Plug User’s Manual 41MAC Address MAC Address: Enter the Wireless BSSID (MAC) 12 characters of the other wireless AP that you want to connect with. To check your wireless router’s MAC address, please go to Status Æ Wireless Configuration to find your BSSID (Wireless MAC address.) Data Rate Select the data rate form the pull-down list. Comment Enter a description for the device. Apply Changes After completing the settings on this page, click Apply changes button to save the settings. Reset After completing the settings on this page, click Apply changes button to save the settings. Set Security Enable the WDS function and then click Set Security button to set up the WDS security. Encryption: Select the encryption type None, WEP 64 bits, WEP 128 bits from the pull-down menu. WEP
4. Web Configuration AirLive N.Plug User’s Manual 42WEP Key Format: For WEP 64 bits and WEP 128 bits encryption type, the selection of WEP Key Format are Hex and ASCII. WEP Key: If select Hex if you are using hexadecimal numbers (0-9, or A-F). Select ASCII if you are using ASCII characters (case-sensitive). Hexadecimal (WEP 64 bits): 10 Hex characters (0~9, a~f). Hexadecimal (WEP 128 bits): 26 Hex characters (0~9, a~f). ASCII (WEP 64 bits): 5 ASCII characters (case-sensitive). ASCII (WEP 128 bits): 13 ASCII characters (case-sensitive). Show Statistics Click Show Statistics to show the current WDS AP table. This table shows the MAC address, transmission packets and errors, reception packets and Tx Rate (Mbps) counters for each configured WDS AP. Refresh: Click to renew the counters information. Close: Click to leave the screen. Current WDS AP List Here shows the current WDS AP information. Delete Selected Click Delete Selected to delete the selected AP information. Delete All Click Delete All to delete all the items. Reset Click Reset to restore the settings.
4. Web Configuration AirLive N.Plug User’s Manual 434.2.6 Site Survey Site Survey Check this button to renew all the listed access point. Next Click the Next button to configure the security setting. Back Go back to previous step. Connect Under the Repeater mode and select a site that you would like to communicate, and then click the Connect button to make a connection.
4. Web Configuration AirLive N.Plug User’s Manual 444.2.7 WPS Disable WPS Check the box to disable the WPS function, default setting is enabled. WPS Status Here shows the current status of the WPS function. Default setting is Configured, click Reset to UnConfigured to re-configured the WPS connection. Self-PIN Number Here shows the 8-digit numbers PIN code of the router itself. Enter the Self-PIN Number to client (Registrar) end and click the PIN button at the client end to make a WPS connection. It will connect with the wireless router within two minutes and get IP address. Push Button Configuration Click Start PBC button (or press the physical WPS button on the Wireless Router once), meanwhile, the client should also click the PBC button simultaneously within 2 minutes. Client PIN Number Enter the client (Enrollee) PIN code into the blank field then click the Start PIN button to make a WPS connection with client. Then, the wireless router will connect to client within 2 minutes and get IP address. Current Key Info This table shows the security status of the Wireless Router. If user would like to set up the security, please go to Wireless > Security.
4. Web Configuration AirLive N.Plug User’s Manual 454.2.8 Schedule Enable Wireless Schedule Check the box to enable the schedule function. Set up the time to schedule the wireless access rule. Select the day and time you want to enable the wireless function.
4. Web Configuration AirLive N.Plug User’s Manual 464.3 Internet Setting 4.3.1 WAN Interface WAN Connection Type DHCP Client If the DHCP Client connection be selected, the PC will obtain the IP address automatically. Host Name: Enter the network area name in the column. MTU Size: The most appropriate MTU (Maximum Transmission Unit) namely the maximum packet size, the default value is 1492 for your application. Reducing the packet size can help connecting to certain web sites or speeding up packet transfer rate. If the incorrect packet size is entered, you may not be able to open certain web sites. Static IP
4. Web Configuration AirLive N.Plug User’s Manual 47 If the Static IP be selected, user have to set up the IP address, subnet mask and default gateway according to the ISP (Internet Service Provider) that provided the related information. IP Address: Enter the WAN IP address provided by your ISP here. Subnet Mask: Enter the subnet mask here. Default Gateway: Enter the default gateway IP address provided by your ISP here. MTU Size: The most appropriate MTU (Maximum Transmission Unit) namely the maximum packet size. Reducing the packet size can help connecting to certain web sites or speeding up packet transfer rate. If the incorrect packet size is entered, you may not be able to open certain web sites. DNS 1: Enter the DNS server IP address(es) provided by your ISP, or you can specify your own preferred DNS server IP address(es). DNS 2/ DNS 3: These servers are optional. You can enter another DNS server’s IP address as a backup. DNS 2 and 3 servers will be used when the DNS 1 server fails.
4. Web Configuration AirLive N.Plug User’s Manual 48PPPoE If the PPPoE be selected, user has to set up the user name and password according to the ISP that provided the related information. User Name: Enter the username that provide by your ISP provider. Maximum input is 32 alphanumeric characters (case sensitive). Password: Enter the password that provide by your ISP provider. Maximum input is 32 alphanumeric characters (case sensitive). Service Name: Enter the Internet service provider name in the column. Connection Type: Select the connection type Continuous, Connect on Demand or Manual from the pull-down menu. If selected Manual user can click Connect button to make a connection. Idle Time: It represents that the device will idle after the minutes you set. The time must be set between 1~1000 minutes. Default value of idle time is 5 minutes. This function will be available when the Connection Type is selected to Connect on Demand. MTU Size: The most appropriate MTU (Maximum Transmission Unit) namely the maximum packet size, the default value is 1452 for your application. Reducing the packet size can help connecting to certain web sites or speeding up packet transfer rate. If the incorrect packet size is entered, you may not be able to open certain web sites.
4. Web Configuration AirLive N.Plug User’s Manual 49PPTP If the PPTP be selected, user has to set up the server IP address, user name and password according to the ISP that provided the related information. IP Address: Enter the WAN IP address provided by your ISP here. Subnet Mask: Enter the subnet mask here. Server IP Address: Enter the PPTP Server IP Address in this column. User Name: Maximum input is 20 alphanumeric characters (case sensitive). Password: Maximum input is 32 alphanumeric characters (case sensitive). Connection Type: Select the connection type Continuous, Connect on Demand or Manual from the pull-down menu. If selected Manual user can click Connect button to make a connection. Idle Time: It represents that the device will idle after the minutes you set. The time must be set between 1~1000 minutes. Default value of idle time is 5 minutes. This function will be available when the Connection Type is selected to Connect on Demand. MTU Size: The most appropriate MTU (Maximum Transmission Unit) namely the maximum packet size, the default value is 1460 for your application. Reducing the packet size can help connecting to certain
4. Web Configuration AirLive N.Plug User’s Manual 50web sites or speeding up packet transfer rate. If the incorrect packet size is entered, you may not be able to open certain web sites. L2TP If the L2TP be selected, user has to set up the server IP address, user name and password according to the ISP that provided the related information. IP Address: Enter the WAN IP address provided by your ISP here. Subnet Mask: Enter the subnet mask here. Server IP Address: Enter the L2TP Server IP Address in this column. User Name: Maximum input is 20 alphanumeric characters (case sensitive). Password: Maximum input is 32 alphanumeric characters (case sensitive). Connection Type: Select the connection type Continuous, Connect on Demand or Manual from the pull-down menu. If selected Manual user can click Connect button to make a connection. Idle Time: It represents that the device will idle after the minutes you set. The time must be set between 1~1000 minutes. Default value of idle time is 5 minutes. This function will be available when the Connection Type is selected to Connect on Demand.
4. Web Configuration AirLive N.Plug User’s Manual 51MTU Size: The most appropriate MTU (Maximum Transmission Unit) namely the maximum packet size, the default value is 1460 for your application. Reducing the packet size can help connecting to certain web sites or speeding up packet transfer rate. If the incorrect packet size is entered, you may not be able to open certain web sites. 3G: If the 3G be selected, user have to set up the user name, password and other information that the 3G connection needed. z Attain DNS Automatically z Set DNS Manually Select to Attain DNS Automatically or select Set DNS Manually to set the DNS server IP address at the following DNS 1~3 columns. Default setting is Attain DNS Automatically. Enter the DNS server IP address(es) provided by your ISP, or you can specify your own preferred DNS server IP address(es). z DNS 1 z DNS 2 z DNS3 DNS 2 server is optional. You can enter another DNS server’s IP address as a backup. DNS 2 server will be used when the DNS 1 server fails. Clone MAC Your ISP may require a particular MAC address in order for you to connect to the Internet. This MAC address is the PC’s MAC address
4. Web Configuration AirLive N.Plug User’s Manual 52address that your ISP had originally connected your Internet connection to. Type in this Clone MAC address in this section to replace the WAN MAC address with the MAC address of that PC. Enable uPNP… Check to enable the listed functions. Apply Changes After completing the settings on this page, click Apply changes button to save the settings. Reset Click Reset to restore to default values. 4.3.2 Port Filtering Enable Port Filtering Check to enable Port Filtering function. Port Range Enter the beginning of the range of port numbers used by the service. If the service uses a single port number, enter it in both the start and finish fields. Protocol Select the protocol (TCP, UDP or Both) used to the remote system or service. Comment You may key in a description MAC address. Apply Changes After completing the settings on this page, click Apply Changes button to save the settings. Reset Click Reset button to restore to default values. Current Filter Table Shows the current Port Forwarding information.
4. Web Configuration AirLive N.Plug User’s Manual 53Delete Selected Click Delete Selected button to delete items which are selected. Delete All Click Delete All button to delete all the items. Reset Click Reset button to rest. 4.3.3 IP Filtering Enable IP Filtering Check to enable IP filtering function. Local IP Address Enter the local computer’s IP address. Protocol Select the protocol (TCP, UDP or Both) used to the remote system or service. Comment You may key in a description for the port range. Apply Changes After completing the settings on this page, click Apply Changes button to save the settings. Reset Click Reset button to restore to default values. Current Filter Table Shows the current IP filter information. Delete Selected Click Delete Selected button to delete items which are selected. Delete All Click Delete All button to delete all the items. Reset Click Reset button to rest.
4. Web Configuration AirLive N.Plug User’s Manual 54 4.3.4 Port Forwarding Enable Port Forwarding Check to enable Port Forwarding function. IP Address Enter the IP address in the field. Protocol Select the protocol (TCP, UDP or Both) used to the remote system or service. Port Range For TCP and UDP Services, enter the beginning of the range of port numbers used by the service. If the service uses a single port number, enter it in both the start and finish fields. Comment You may key in a description MAC address. Apply Changes After completing the settings on this page, click Apply Changes button to save the settings. Reset Click Reset button to restore to default values. Current Port Forwarding Table Shows the current Port Forwarding information. Delete Selected Click Delete Selected button to delete items which are selected.
4. Web Configuration AirLive N.Plug User’s Manual 55Delete All Click Delete All button to delete all the items. Reset Click Reset button to rest. 4.3.5 URL Filtering Enable URL Filtering Check to enable URL filtering function. URL Address Enter the URL address in the field Apply Changes After completing the settings on this page, click Apply Changes button to save the settings. Reset Click Reset button to restore to default values. Current Filter Table Shows the current URL address filter information. Delete Selected Click Delete All button to delete all the items. Reset Click Reset button to rest.
4. Web Configuration AirLive N.Plug User’s Manual 564.3.6 DMZ Enable DMZ Check the box to enable DMZ function. If the DMZ Host Function is enabled, it means that you set up DMZ host at a particular computer to be exposed to the Internet so that some applications/software, especially Internet / online game can have two way connections. DMZ Host IP Address Enter the IP address of a particular host in your LAN which will receive all the packets originally going to the WAN port/Public IP address above. Note You need to give your LAN PC clients a fixed/static IP address for DMZ to work properly. Apply Changes After completing the settings on this page, click Apply Changes button to save the settings. Reset Click Reset button to restore to default values
4. Web Configuration AirLive N.Plug User’s Manual 574.3.7 DDNS Enable DDNS Check to enable the DDNS function. Service Provider Select the desired DDNS Service Provider DynDNS or TZO from the pull-down list. Domain Name Here shows the domain name of the service provider. User Name/Email Enter your email that you registered in service provider website. (You can refer to below Note information to apply a account form the service provider website.) Password/Key Enter your passwords that you registered in service provider website. Maximum input is 30 alphanumeric characters (case sensitive). Apply Changes After completing the settings on this page, click Apply Changes button to save the settings. Reset Click Reset button to restore to default values.
4. Web Configuration AirLive N.Plug User’s Manual 584.3.8 Router Setup
4. Web Configuration AirLive N.Plug User’s Manual 59Enable Dynamic Route Dynamic routing performs the same function as static routing except it is steadier. Dynamic routing allows routing tables in routers to change as the possible routes change. There are several protocols used to support dynamic routing including RIP and OSPF. NAT Network Address Translation (NAT) selects to enable or disable this function. Transmit Select to enable or disable RIP protocol for transmit. Receive Select to enable or disable RIP protocol for receive. Enable Static Route If you connect several routers with this Wireless Router, you may need to set up a predefined routing rule to have more effective network topology/traffic, this is called static route between those routers and the Wireless Router. To set static routers, enter the settings including route IP address, route mask, route gateway and the route Interface from LAN or WAN. IP Address Set up the IP address that would like to send the packets pass through. Subnet Mask Set up the Subnet Mask that would like to send the packets pass through. Gateway Set up the gateway that would like to send the packets pass through. Metric It is used by a router to make routing decisions. The metrics used by a router to make routing decisions. It is typically one of many fields in a routing table. Router metrics can contain any number of values that help the router determine the best route among multiple routes to a destination. A router metric typically based on information like path length, bandwidth, load, hop count, path cost, delay, Maximum Transmission Unit (MTU), reliability and communications cost. Interface Select the interface of the setting path.
4. Web Configuration AirLive N.Plug User’s Manual 604.4 System 4.4.1 LAN Interface IP Address Shows the IP address of the Wireless Router. Default IP address is 192.168.1.254 (Router/AP mode) or 192.168.1.253 (Client Mode). Subnet Mask The subnet mask of the Wireless Router (Default subnet mask is 255.255.255.0.) Default Gateway Enter the Gateway IP address here. DHCP Disable: Select to disable this Wireless Router to distribute IP addresses to connected clients. Server: Select to enable this Wireless Router to distribute IP Addresses (DHCP Server) to connected clients. And the following field will be activated for you to enter the starting IP address. DHCP Client Range The starting address of this local IP network address pool. The pool is a piece of continuous IP address segment, the device will distribute IP addresses from 192.168.1.100 to 192.168.1.200 to all the computers in the network that request IP addresses from DHCP server (Router). The end IP address maximum is 253. Note: If “Continuous IP address pool starts” is set at 192.168.1.1 and the
4. Web Configuration AirLive N.Plug User’s Manual 61“Number of IP address in pool end” is 253, the device will distribute IP addresses from 192.168.1.100 to 192.168.1.253 to all the computers in the network that request IP addresses from DHCP server (Router). Click Show Client button to show Active DHCP Client Table. The table shows assigned IP address, MAC address and time expired for each client. Refresh: Click this button to refresh the table. Close: Click this button to close the window. Static DHCP Check the box to enable the Static DHCP function, default setting is disabled. When set to enabled, user can click Set Static DHCP button to set the Static DHCP function.
4. Web Configuration AirLive N.Plug User’s Manual 62 IP Address: Enter the fixed IP address that DHCP server assigned to a certain connected station. MAC Address: Enter the MAC address of a certain station, and then the DHCP server will to distribute a fixed IP address to the station automatically once they connected. Comment: You can enter a comment to description above IP address or MAC address. Apply Changes: After completing the settings on this page, click Apply changes button to save the settings. Reset: Click Reset to restore to default values. Static DHCP List: Here shows the static IP address that have been assigned according to the MAC address. Delete Selected: Click Delete Selected to delete items which are selected. Delete All: Click Delete All button to delete all the items. Reset: Click Reset button to rest. Domain Name Enter the network area name here. 802.1d Spanning Tree Select Disabled or Enabled form the pull-down list. Clone MAC Address Your ISP may require a particular MAC address in order for you to connect to the Internet. This MAC address is the PC’s MAC address that your ISP had originally connected your Internet connection to. Type in the MAC address to replace the WAN MAC address with the MAC address of that PC.
4. Web Configuration AirLive N.Plug User’s Manual 634.4.2 Time Zone Setting Current Time Enter the current time of this wireless router or click the Copy Computer Time button to synchronize the time with the connected computer automatically. Time Zone Select Select the local time zone from the pull-down menu. Enable NTP client update Check to enable NTP (Network Time Protocol Server) client update function. Automatically Adjust Daylight Saving Check the box to enable this function. NTP server Manual IP Setting You may choose to select NTP server from the pull-down menu or enter an IP address of a specific server manually. Apply Changes After completing the settings on this page, click Apply Changes button to save current settings. Refresh Click Refresh button to renew current time.
4. Web Configuration AirLive N.Plug User’s Manual 644.4.3 Denial-of-Service Enable DoS Prevention DoS (Denial of Service) attacks can flood your Internet connection with invalid packets and connection requests, using so much bandwidth and so many resources that Internet access becomes unavailable. The Wireless Router incorporates protection against DoS attacks. This screen allows you to configure DoS protection. Check the box to enable the DoS settings.
4. Web Configuration AirLive N.Plug User’s Manual 65Select All After you enabled the DoS prevention, you can click to select all DoS preventions. Clear All After you enabled the DoS prevention, you can click to uncheck all DoS preventions. Apply Changes After completing the settings on this page, click Apply Changes button to save current settings. 4.4.4 Upgrade Firmware Select File Click the Browse button to find and open the firmware file (the browser will display to correct file path.) Upload Click the Upload button to perform. Reset Click Reset button to restore to default values. 4.4.5 Save/Reload Setting
4. Web Configuration AirLive N.Plug User’s Manual 66Save Settings to File Click the Save button to save the current settings file in the PC. Load Settings form File Click the Browse button to find and open the previous saved file (the browser will display to correct file path.) Then, click Upload button to upload the previous file. Reset Settings to Default Click Reset button to set the device back to default settings. 4.4.6 Password User Name Key in a new login user name in the blank field. User can empty the user name and password columns to disable the access. New Password Maximum input is 30 alphanumeric characters (case sensitive.) Confirmed Password Key in the password again to confirm.
4. Web Configuration AirLive N.Plug User’s Manual 674.4.7 QoS
4. Web Configuration AirLive N.Plug User’s Manual 68Enable QoS This function improves online gaming experience by ensuring that game traffic is prioritized over other network traffic, such as FTP or Web. Automatic Uplink/Download Speed Check the box to enable the automatic uplink/ download speed function. Manual Uplink/Download Speed You can manually enter the uplink/ download transmission rate in the blank field. Address Type Select IP or MAC address type. Local IP address MAC address Depend on the address type that selected, user can enter the IP address or MAC address of client to set up the bandwidth of the transmission. Mode Select Guaranteed minimum bandwidth or Restricted maximum bandwidth modes. Uplink Bandwidth (Kbps) Enter the Uplink Bandwidth (Kbps) in the column. Downlink Bandwidth (Kbps) Enter the Downlink Bandwidth (Kbps) in the column. Comment Enter the note for the setting.
4. Web Configuration AirLive N.Plug User’s Manual 694.5 Ststus 4.5.1 Status User can check the running information about N.Plug in this page.
4. Web Configuration AirLive N.Plug User’s Manual 704.5.2 Statistics User can check the wireless connection information in this page.
4. Web Configuration AirLive N.Plug User’s Manual 714.5.3 Log User can check the system log in this page. 4.6 Reboot User can reboot the N.Plug by clicking the Reboot button.
5. PC Configuration AirLive N.Plug User’s Manual 72 5.1 Overview For each PC, the following may need to be configured: z TCP/IP network settings z Internet Access configuration z Wireless configuration 5.2 Windows Clients z This section describes how to configure Windows clients for Internet access via the Wireless Router. z The first step is to check the PC's TCP/IP settings. z The Wireless Router uses the TCP/IP network protocol for all functions, so it is essential that the TCP/IP protocol be installed and configured on each PC. 5.2.1 TCP/IP Settings – Overview If using default Wireless Router settings, and default Windows TCP/IP settings, no changes need to be made. z By default, the Wireless Router will act as a DHCP Server, automatically providing a suitable IP address (and related information) to each PC when the PC boots. z For all non-Server versions of Windows, the default TCP/IP setting is to act as a DHCP client. If using a Fixed (specified) IP address, the following changes are required: z The Gateway must be set to the IP address of the Wireless Router. z The DNS should be set to the address provided by your ISP. 5 5. PC Configuration
5. PC Configuration AirLive N.Plug User’s Manual 735.2.2 Checking TCP/IP Settings - Windows 2000 1. Select Control Panel - Network and Dial-up Connection. 2. Right - click the Local Area Connection icon and select Properties. You should see a screen like the following: 3. Select the TCP/IP protocol for your network card.
5. PC Configuration AirLive N.Plug User’s Manual 744. Click on the Properties button. You should then see a screen like the following. Ensure your TCP/IP settings are correct, as described below. Using DHCP z To use DHCP, select the radio button Obtain an IP Address automatically. This is the default Windows setting. Using this is recommended. By default, the Wireless Router will act as a DHCP Server. z Restart your PC to ensure it obtains an IP Address from the Wireless Router. Using a fixed IP Address ("Use the following IP Address") If your PC is already configured, check with your network administrator before making the following changes. z Enter the Wireless Router 's IP address in the Default gateway field and click OK. (Your LAN administrator can advise you of the IP Address they assigned to the Wireless Router.) z If the DNS Server fields are empty, select Use the following DNS server addresses, and enters the DNS address or addresses provided by your ISP, then click OK.
5. PC Configuration AirLive N.Plug User’s Manual 755.2.3 Checking TCP/IP Settings - Windows XP 1. Select Control Panel - Network Connection. 2. Right click the Local Area Connection and choose Properties. You should see a screen like the following: 3. Select the TCP/IP protocol for your network card. 4. Click on the Properties button. You should then see a screen like the following.
5. PC Configuration AirLive N.Plug User’s Manual 76 5. Ensure your TCP/IP settings are correct. Using DHCP z To use DHCP, select the radio button Obtain an IP Address automatically. This is the default Windows setting. Using this is recommended. By default, the Wireless Router will act as a DHCP Server. z Restart your PC to ensure it obtains an IP address from the Wireless Router. Using a fixed IP Address ("Use the following IP Address") If your PC is already configured, check with your network administrator before making the following changes. z In the Default gateway field, enter the Wireless Router’s IP address and click OK. Your LAN administrator can advise you of the IP Address they assigned to the Wireless Router. z If the DNS Server fields are empty, select Use the following DNS server addresses, and enters the DNS address or addresses provided by your ISP, then click OK.
5. PC Configuration AirLive N.Plug User’s Manual 775.2.4 Checking TCP/IP Settings - Windows Vista 1. Go to Start > Control Panel> Network and Internet> Network and Sharing Center> Manage Network Connections> Local Area Connection. 2. Right click the Local Area Connection icon and choose Properties. You should see a screen like the following: 3. Select the Internet Protocol Version 4(TCP/IPv4) or 6 (TCP/IPv6) for your network card. .
5. PC Configuration AirLive N.Plug User’s Manual 784. Click on the Properties button. You should then see a screen like the following. 5. Ensure your TCP/IP settings are correct. Using DHCP z To use DHCP, select Obtain an IP address automatically and Obtain DNS server address automatically. This is the default Windows setting. Using this is recommended. By default, the Wireless Router will act as a DHCP Server. z Restart your PC to ensure it obtains an IP address from the Wireless Router. Using a fixed IP Address ("Use the following IP Address") If your PC is already configured, check with your network administrator before making the following changes. z In the Default gateway field, enter the Wireless Router 's IP address. Your LAN administrator can advise you of the IP address they assigned to the Wireless Router. z If the DNS Server fields are empty, select Use the following DNS server addresses, and enters the DNS address or addresses provided by your ISP, then click OK.
5. PC Configuration AirLive N.Plug User’s Manual 795.2.5 Checking TCP/IP Settings - Windows 7 1. Go to Start > Control Panel> Network and Sharing Center> Manage Network Connections> Local Area Connection. 2. Right click the Local Area Connection icon and choose Properties. You should see a screen like the following: 3. Select the Internet Protocol Version 4(TCP/IPv4) or 6 (TCP/IPv6) for your network card.
5. PC Configuration AirLive N.Plug User’s Manual 805. Click on the Properties button. You should then see a screen like the following. 6. Using DHCP z To use DHCP, select Obtain an IP address automatically and Obtain DNS server address automatically. This is the default Windows setting. Using this is recommended. By default, the Wireless Router will act as a DHCP Server. z Restart your PC to ensure it obtains an IP address from the Wireless Router. Using a fixed IP Address ("Use the following IP Address") If your PC is already configured, check with your network administrator before making the following changes. z In the Default gateway field, enter the Wireless Router 's IP address. Your LAN administrator can advise you of the IP address they assigned to the Wireless Router. z If the DNS Server fields are empty, select Use the following DNS server addresses, and enters the DNS address or addresses provided by your ISP, then click OK.
5. PC Configuration AirLive N.Plug User’s Manual 815.2.6 Internet Access To configure your PCs to use the Wireless Router for Internet access: z Ensure that the ADSL modem, DSL modem, Cable modem, or other permanent connection is functional. z Use the following procedure to configure your Browser to access the Internet via the LAN, rather than by a Dial-up connection. For Windows 2000 1. Select Start menu - Settings - Control Panel - Internet Options. 2. Select the Connection tab, and click the Setup button. 3. Select "I want to set up my Internet connection manually, or I want to connect through a local area network (LAN)" and click Next. 4. Select "I connect through a local area network (LAN)" and click Next. 5. Ensure all of the boxes on the following Local area network Internet Configuration screen are unchecked. 6. Check the "No" option when prompted "Do you want to set up an Internet mail account now?" 7. Click Finish to close the Internet Connection Wizard. Setup is now completed. For Windows XP 1. Select Start menu >Control Panel > Network and Internet Connections. 2. Select Set up or change your Internet Connection. 3. Select the Connection tab, and click the Setup button. 4. Cancel the pop-up "Location Information" screen. 5. Click Next on the "New Connection Wizard" screen. 6. Select "Connect to the Internet" and click Next. For Windows Vista 1. Select Start menu > Control Panel > Network and Internet> Network and Sharing Center. 2. Select Set up a connection or network. 3. Select Connect to the Internet and click Next to continue. 4. Select Broadband (PPPoE). 5. Enter User name and Password that provided by the ISP, then click Connect to make a connection.
5. PC Configuration AirLive N.Plug User’s Manual 82For Windows 7 1. Select Start menu > Control Panel > Network Sharing Center. 2. Select Set up a new connection or network. 3. Select Connect to the Internet and click Next to continue. 4. Select Broadband (PPPoE). 5. Enter User name and Password that provided by the ISP, then click Connect to make a connection. Accessing AOL To access AOL (America On Line) through the Wireless Router, the AOL for Windows software must be configured to use TCP/IP network access, rather than a dial-up connection. The configuration process is as follows: 1. Start the AOL for Windows communication software. Ensure that it is Version 2.5, 3.0 or later. This procedure will not work with earlier versions. 2. Click the Setup button. 3. Select Create Location, and change the location name from "New Locality" to " Wireless Router ". 4. Click Edit Location. Select TCP/IP for the Network field. (Leave the Phone Number blank.) 5. Click Save, then OK. 6. Configuration is now complete. 7. Before clicking "Sign On", always ensure that you are using the " Wireless Router " location.
5. PC Configuration AirLive N.Plug User’s Manual 835.2.7 Macintosh Clients From your Macintosh, you can access the Internet via the Wireless Router. The procedure is as follow 1. Open the TCP/IP Control Panel. 2. Select Ethernet from the Connect via pop-up menu. 3. Select Using DHCP Server from the Configure pop-up menu. The DHCP Client ID field can be left blank. 4. Close the TCP/IP panel, saving your settings. Note If using manually assigned IP addresses instead of DHCP, the required changes are: z Set the Router Address field to the Wireless Router 's IP Address. z Ensure your DNS settings are correct. 5.2.8 Linux Clients To access the Internet via the Wireless Router, it is only necessary to set the Wireless Router as the "Gateway". Ensure you are logged in as "root" before attempting any changes. Fixed IP Address By default, most Unix installations use a fixed IP Address. If you wish to continue using a fixed IP Address, make the following changes to your configuration. z Set your "Default Gateway" to the IP Address of the Wireless Router. z Ensure your DNS (Domain Name server) settings are correct. To act as a DHCP Client (Recommended) The procedure below may vary according to your version of Linux and X -windows shell. 1. Start your X Windows client. 2. Select Control Panel – Network. 3. Select the "Interface" entry for your Network card. Normally, this will be called "eth0". 4. Click the Edit button, set the "protocol" to "DHCP", and save this data. 5. To apply your changes: z Use the "Deactivate" and "Activate" buttons, if available. z OR, restart your system.
5. PC Configuration AirLive N.Plug User’s Manual 845.2.9 Other Unix Systems To access the Internet via the Wireless Router: z Ensure the "Gateway" field for your network card is set to the IP Address of the Wireless Router. z Ensure your DNS (Name Server) settings are correct. 5.2.10 Wireless Station Configuration z This section applies to all wireless stations wishing to use the Wireless Router 's access point, regardless of the operating system that is used on the client. z To use the Wireless Router, each wireless station must have compatible settings, as following: Mode The mode must be set to Infrastructure. SSID (ESSID) The network name must match the value used on the Wireless Router. Note The SSID is case- sensitive. Disable If there is no security is enabled on the Wireless Router, the security of each station should be disabled as well. And, you can connect the Wireless Router without security, but it is NOT recommended. WEP By default, WEP on the Wireless Router is disabled. z If WEP remains disabled on the Wireless Router, all stations must have WEP disabled. z If WEP is enabled on the Wireless Router, each station must use the same settings as the Wireless Router. WPA WPA2 WPA-Mixed 802.1x RADIUS Server: RADIUS is an authentication, authorization and accounting client-server protocol. The client is a Network Access Server that desires to authenticate its links. The server is a server that has access to a user database with authentication information. Each station must set up the RADIUS Server’s IP address, port and passwords that provided by your ISP. Note By default, the Wireless Router will allow 802.11b, 802.11g and 802.11n connection
Appendix A Troubleshooting AirLive N.Plug User’s Manual 85 Overview This chapter covers some common problems that may be encountered while using the Wireless Router and some possible solutions to them. If you follow the suggested steps and the Wireless Router still does not function properly, contact your dealer for further advice. General Problems Problem 1: Can't connect to the Wireless Router to configure it. Solution 1: Check the following: z Check the Wireless Router is properly installed, LAN connections are OK, and it is powered ON. z Ensure that your PC and the Wireless Router are on the same network segment. z If your PC is set to "Obtain an IP Address automatically" (DHCP client), please restart it. z If your PC uses a Fixed (Static) IP address, ensure that it is using an IP Addresswithin the range 192.168.1.1 to 192.168.1.253 and thus compatible with the Wireless Router's default IP Address of 192.168.1.253. Also, the Network Mask should be set to 255.255.255.0 to match the Wireless Router. In Windows, you can check these settings by using Control Panel-Network to check the Properties for the TCP/IP protocol. Internet Access Problem 1: When I enter a URL or IP address I get a time out error. Solution 1: A number of things could be causing this. Try the following troubleshooting steps. z Check if other PCs work. If they do, ensure that your PCs IP settings are correct. If using a Fixed (Static) IP Address, check the Network Mask, Default gateway and DNS as well as the IP Address. z If the PCs are configured correctly, but still not working, check the Wireless Router. Ensure that it is connected and A Appendix A: Troubleshooting
Appendix A Troubleshooting AirLive N.Plug User’s Manual 86ON. Connect to it and check its settings. (If you can't connect to it, check the LAN and power connections.) z If the Wireless Router is configured correctly, check your Internet connection (DSL/Cable modem etc) to see that it is working correctly. Problem 2: Some applications do not run properly when using the Wireless Router. Solution 2: The Wireless Router processes the data passing through it, so it is not transparent. Use the Content Filter Settings feature to allow the use of Internet applications, which do not function correctly. If this does solve the problem you can use the DMZ function. This should work with almost every application, but: z It is a security risk, since the firewall is disabled. z Only one (1) PC can use this feature. Wireless Access Problem 1: My PC can't locate the Wireless Router. Solution 1: Check the following: z Your PC is set to Infrastructure Mode. (Access Points are always in Infrastructure Mode) z The SSID on your PC and the Wireless Router are the same. z Remember that the SSID is case-sensitive. So, for example "Workgroup" does NOT match "workgroup." z Both your PC and the Wireless Router must have the same setting for security. The default setting for the Wireless Router security is disabled, so your wireless station should also have security disabled. z If security is enabled on the Wireless Router, your PC must have security enabled, and the key must be matched. z To see if radio interference is causing a problem, see if connection is possible when close to the Wireless Router. Remember that the connection range can be as little as 100 feet in poor environments. Problem 2: Wireless connection speed is very slow. Solution 2: The wireless system will connect at the highest possible speed, depending on the distance and the environment. To obtain the
Appendix A Troubleshooting AirLive N.Plug User’s Manual 87highest possible connection speed, you can experiment with the following: z Wireless Router location Try adjusting the location and orientation of the Wireless Router. z Wireless Channel If interference is the problem, changing to another channel may show a marked improvement. z Radio Interference Other devices may be causing interference. You can experiment by switching other devices off, and see if this helps. Any "noisy" devices should be shielded or relocated. z RF Shielding Your environment may tend to block transmission between the wireless stations. This will mean high access speed is only possible when close to the Wireless Router.
Appendix B About Wireless LANs AirLive N.Plug User’s Manual 88 BSS A group of Wireless Stations and a single Access Point, all using the same ID (SSID), form a Basic Service Set (BSS). Using the same SSID is essential. Devices with different SSIDs are unable to communicate with each other. Channels The Wireless Channel sets the radio frequency used for communication. z Access Points use a fixed Channel. You can select the Channel used. This allows you to choose a Channel which provides the least interference and best performance. In the USA and Canada, 11 channel are available. If using multiple Access Points, it is better if adjacent Access Points use different Channels to reduce interference. z In "Infrastructure" mode, Wireless Stations normally scan all Channels, looking for an Access Point. If more than one Access Point can be used, the one with the strongest signal is used. (This can only happen within an ESS.) Note To comply with US FCC regulation, the country selection function has been completely removed from all US models. The above function is for non-US models only. Security z WEP WEP (Wired Equivalent Privacy) is a standard for encrypting data before it is transmitted. This is desirable because it is impossible to prevent snoopers from receiving any data which is transmitted by your Wireless Stations. But if the data is encrypted, then it is meaningless unless the receiver can decrypt it. If WEP is used, the Wireless Stations and the Access Point must have the same security settings for each of the following: WEP 64 Bits, 128 Bits. Key For 64 Bits encryption, the Key value must match. For 128 Bits encryption, the Key value must match. WEP Authentication Open System or Shared Key. B Appendix B: About Wireless LANs
B. Appendix B About Wireless LANs AirLive N.Plug User’s Manual 89z WPA/WPA2/ WPA-Mixed WPA/WPA2 (Wi-Fi Protected Access) is more secure than WEP. It uses a “Shared Key” which allows the encryption keys to be regenerated at a specified interval. There are several encryption options: TKIP, AES, TKIP-AES and additional setup for RADIUS is required in this method. The most important features beyond WPA to become standardized through 802.11i/WPA2 are: pre-authentication, which enables secure fast roaming without noticeable signal latency. If WPA or WPA2 is used, the Wireless Stations and the Access Point must have the same security settings. z 802.1x With 802.1x authentication, a wireless PC can join any network and receive any messages that are not encrypted, however, additional setup for RADIUS to issue the WEP key dynamically will be required. RADIUS is an authentication, authorization, and accounting client-server protocol. The client is a Network Access Server that desires to authenticate its links. The server is a server that has access to a user database with authentication information. Wireless LAN Configuration To allow Wireless Stations to use the Access Point, the Wireless Stations and the Access Point must use the same settings, as follows: Mode The mode must be set to Infrastructure. SSID (ESSID) The network name must match the value used on the Wireless Router. Note The SSID is case- sensitive. Disable If there is no security is enabled on the Wireless Router, the security of each station should be disabled as well. And, you can connect the Wireless Router without security, but it is NOT recommended. WEP Open System/ Shared Key/ Auto By default, WEP on the Wireless Router is disabled. Shared Key only supports WEP as encryption method. AUTO(Open/Shared) means AP can accept STA connect to it using OPEN-WEP or SHARED-WEP. z If WEP remains disabled on the Wireless Router, all stations must have WEP disabled. z If WEP is enabled on the Wireless Router, each station must use the same settings as the Wireless Router. Personal WPA-PSK (TKIP/AES)/ WPA2-PSK (TKIP/AES:
Appendix B About Wireless LANs AirLive N.Plug User’s Manual 90(Pre-Shared Key) WPA WPA2 WPA2-Mixed If one of these securities is enabled on the Wireless Router. To make a connection, each station must use the same algorithms and pass phrase as the Wireless Router. Pre-Shared Key Format: There are two formats for choice to set the Pre-shared key, Passphrase and Hex (64 characters). If Hex is selected, users will have to enter a 64 characters string. For easier configuration, the Passphrase (at least 8 characters) format is recommended. Pre-Shared Key : Pre-Shared Key serves as a password. Users may key in 8 to 63 characters string if you selected passphrase. Pre-shared key format to set the passwords or leave it blank, in which the 802.1x Authentication will be activated. Make sure the same password is used on client's end. Enterprise (RADIUS) WPA WPA2 WPA2-Mixed 802.1x RADIUS Server: RADIUS is an authentication, authorization and accounting client-server protocol. The client is a Network Access Server that desires to authenticate its links. The server is a server that has access to a user database with authentication information. Each station must set up the RADIUS Server’s IP address, port and passwords that provided by your ISP.

Navigation menu