PAKITE TECHNOLOGY 24GAVSENDER RCA AV Sender & IR Remote Extender User Manual

SHENZHEN PAKITE TECHNOLOGY CO.,LTD. RCA AV Sender & IR Remote Extender

User Manual

FCC STATEMENT§15.19 Labelling requirements.This device complies with part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that maycause undesired operation.§15.21 Information to user.Any Changes or modifications not expressly approved by the party responsible forcompliance could void the user's authority to operate the equipment.§15.105 Information to the user.Note: This equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residentialinstallation. This equipment generates uses and can radiate radio frequency energyand, if not installed and used in accordance with the instructions, may cause harmfulinterference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.-Consult the dealer or an experienced radio/TV technician for help.FCC Radiation Exposure Statement*RF warning for Mobile device:This equipment complies with FCC radiation exposure limits set forth for anuncontrolled environment. This equipment should be installed and operated withminimum distance 20cm between the radiator & your body.
The copyright of this manual belongs to the manufacturer.Esteemed Customers:Thank you for purchasing our product!You will enjoy the fun brought by Wireless Audio Video Transmitteralong with all the global users who firmly support us. Please do read thisguide book carefully and thoroughly for better use of this product. Itworks for home use. Every check of this product (if it works normally)before uses it is necessary. If there any default or damage of this product,please maintain or repair it in time.This final explanation of the content written in this manual book belongsto its manufacturer. Anyone or any party is not allowed to copy all orpartial content of this Manual Book. It is not authorized to anyone orany party. No notifications would be given, if any change of this ManualBook.Thanks for buying our products along with the global users. “The Digital Wireless STBSharing device” is a kind of electronic product, which can realize the audio videosignal sharing in different rooms for family entertainment. It consists of a transmitterand a receiver. Adopting advanced 2.4GHz wireless transmission schemes andhaving advantages of long distance transmission, strong anti-interference and highmobility. By means of radio waves, it can transmit the signal from DVD player, DVR,CCTV camera, IPTV, Satellite receiver, Digital TV Set Top Box or any other AVdevices at transmitter end to TV sets in different room at receiver end. it can supportthe IR remote control at the receiver end to realize the function of wireless control ofdevices from another place. So that you can enjoy freely wireless HD AV sharing dataand Hi-Fi audio and video effect.1. Function & FeaturesUse 2.4GHz ISM frequency band, multiple selective channels supported foranti-interference from wireless.Support 1 group of AV signal input/output.Keep Transmitter and receiver setting at the same channel, it can support 1transmitter and more receivers at the same time.Support DVD, DVR, IPTV, CCTV Camera, Satellite receiver, Digital STB andother AV output devices.Support superheterodyne 433MHz infrared remote signal transmission, whileCompatible for 38KHz infrared carrier control signal.Transmitter have built-in infrared signal emission or infrared transmissionextension cable, so that you can do remote control the signal from DVD, DVR,STB, IPTV, and other device.Supports video transmission of PAL/NTSC system and stereo audio transmission,Pictures received are clear, flamboyant and stable.Full hardware design without installing any software, plug and play, simple andconvenient. Fashionable design, Machine dimensions: 10×8.5×3.0 cm.■■■■■■■■■
2. Standard accessoriesTransmitter ………………………………………………………………………………Receiver …………………………………………………………………………………Power Adapter ……………………………………………………………………………RCA Wire …………………………………………………………………………………IR Extender Wire ………………………………………………………………………..Use Manual………………………………………………………………………………3. SpecificationsPower input: DC 5V 1000mAVideo input: 1Vp-p(PAL/NTSC)Audio input: 1.5Vp-p (dual channel)Video output: 1Vp-p(PAL/NTSC)Audio output: 1.5Vp-p (dual channel)1. Allocation1 set1 set2 pcs2 pcs1 pcs1 copy2. Transmitter panel description3. Receiver panel description
4. Transmitter installation■Put the transmitter near to STB and other AV output devices, connect the AVcable with the audio video output signal of STB corresponding to colors(Red,White, Yellow).■Put the transmitter above the STB or other device so that the IR transmittingwindow extrudes out by 1 to 2 cm and vertically aims at the receiving window ofthe IR signal of the STB or other device.Hints：The receiving window of the IR signal of the STB or other device is generallymarked with “IR”. Please vertically aim at the IR signal transmitting window ofthe transmitter. And keep the transmitter away from other devices and metaldevices to avoid effecting wireless signal transmitter.5.Receiver installationPut the transmitter near to STB and other AV output devices, connect the AV cablewith the audio video input signal of TV corresponding to colors(Red, White, Yellow),and modulate the TV channels to video channel until it shows receiving pictures.Hints：After receiver connects the TV sets, you should change from TV to AV channels andkeep the transmitter away from other devices and metal devices to avoid effectingwireless signal transmitter.6. Allocation of 433MHz antennaPlease pay attention to the allocation of the 433MHz antenna. Make sure there isno obstacle around the 433MHz antenna, especially metal obstacles which mayseriously impact wireless retransmission of IR signals.
Hints:When arranging the transmitter and receiver, make sure there is no obstacle aroundthe 2.4G/2.4G antenna and the 433MHz antenna. Otherwise transmission of thesignal will be affected.3. 433MHz Wireless IR Remote Extender2.4G/2.4G Digital STB wireless sharing device needs no remote controller. If the STBor other device is equipped with a remote controller, you can use it to remotely controlthe receiver end to realize the function of wireless remote control from another place.Transmitting RF：1. Transmission frequency: 433.92MHz±200KHz Superheterodyne2. Carrier frequency: 38KHz3. IR signal Receiving: ≤10mReceiving RF：1. Transmission frequency: 433.92MHz±500KHz Superheterodyne2. Carrier frequency: 38KHz3. IR signal Transmitting:≤5m1. Power switchPressing the power switch can switch on or off the power to the transmitter orreceiver and enable it to transmit or not transmit the signal.Hints:To ensure that the product can be used normally, the product should be connected whenpower off In case the product be damaged. Switch on when finish connection and neverplug in or out at will. Please turn off the product if long time not use it.2. 2.4GHz channel selectionPress the Channel switches can be free to choose 2.4GHz transmission channel.AV signal can be transmitted normally only when the transmitter and the receiver are onthe same channel.■2.4GHz /2.4GHz transmission channel(turn the switch down)：Hints:Please select the 2.4GHz transmission channel with the best image and sound effectaccording to the actual operation environment. If there is interference from the routersignal in the environment, please select another 2.4GHz transmission channel to avoidthe interference source.Hints:If the Wireless IR Remote Extender is not sensitive, you can adjust the relativelocations of the transmitter and the receiver. Keep them away from the AV connectionwires or other metal objects to ensure barrier-free signal transmission.
1. If the indicator lamps do not light up and there is no image.A. Please check the power connection of the transmitter and receiver, open thepower switch.B. Please try to change the 2.4GHz transmission channel for the transmitter and thereceiver.C. Please check if the transmitter and the receiver are connected correctly (Refer toinstallation instruction).2. IR remote controller fails to work.A. Adjust the location of the transmitter and the receiver.B. Plug out the transmitter and the receiver and restart 1~2 minutes later.C. Please check whether the transmitter bulge 1-2 cm out of the STB or not.3. The image is interfered.A. Please adjust the angle of the antenna for 2.4GHz transmitter and thereceiver.B. Please try to change the 2.4GHz transmission channel for thetransmitter and the receiver.C. If allowed, please put the transmitter and the receiver in a higher place tostrengthen the wireless transmission.Switch on only after finishing the connection and never plug in or out at will. Theproduct is for home use instead of professional industrial use. Please don’t takeapart without proper professional knowledge.1. Warranty is only available to customers who buy this productthrough legal approach.2. After-sales promise：Every customer designated dealers to buy products in our company, if there isproduct quality problems under the normal use within 3 months from the day youbuy the machine, user can bring the valid credentials or sales invoice to theoriginal dealer where you bought it to replace the same model of the products.If there are product quality problems within 12 months, you can request freewarranty (not including common accessories).3. Additional fee will be charged in any of the following situations:A. The warranty period is expired.B. Failure or damage caused by connecting other device.C. Failure or damage caused by repairing or transforming by yourself.D. Failure or damage caused by not following the operation instructions of theproduct.E. Failure or damage caused by collision, falling or other non-quality problems.F. Dam age caused by fire, lightning strike or other unexpected disasters.For repairing products which are damaged by the above situations, users shouldbear the fee of replacement of the damaged components as well as the shipping fee.Solemn Statement:The manufacturer assumes no liability for irreversible damage or damages to otherdevices caused by these situations.Dear user:Thank you for buying this device. In order to ensure that you can fully enjoy our perfectafter-sale service of our company, please carefully read the comments of this productservice card.
Comments:1. Please reserve this card carefully. If you lose it, you can not get another copy.2. Please show this card together with your purchase receipt when applying forwarranty service.3. This card is invalid without the seal of the distributor.

Navigation menu