PAX Technology CM7ABW PX Communication Module User Manual

PAX Technology Limited PX Communication Module

User Manual

Download: PAX Technology CM7ABW PX Communication Module User Manual
Mirror Download [FCC.gov]PAX Technology CM7ABW PX Communication Module User Manual
Document ID3709899
Application ID7/JYEzPqRQaQyeb1ywKCSg==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize15.88kB (198552 bits)
Date Submitted2018-01-11 00:00:00
Date Available2018-07-11 00:00:00
Creation Date2017-12-21 17:13:07
Producing SoftwareAdobe PDF Library 15.0
Document Lastmod2017-12-21 17:13:08
Document TitleUser Manual
Document CreatorAcrobat PDFMaker 15 Word 版
Document Author: qyb

Px
Communication Module
PAX TECHNOLOGY INC.
1.Product Description
2. Remove Power
Power down and remove all power from the terminal before removing or installing the
communication module.
3. Remove Screw
On the underside of the terminal, loosen the captive screw that holds the installed
communication module in place using a slotted screwdriver.
4. Remove Module
Gently pry open the screw end of the module using a blunt object such as a coin or
screwdriver. Carefully lift the module out from the underside of the terminal. Do not force or
twist the module.
5. Align Module
Remove the new module from its packaging. Insert the tabs opposite the screw end into the
matching openings on the underside of the terminal.
6. Install Module
Slowly lower and gently press the module into position. Do not force or twist the module.
Tighten the screw that holds the communication module into place. Operate the terminal
as usual.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following measures:




Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
 Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment.
 This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and
users, and the maximum antenna gain allowed for use with this device is 2dBi.
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still
responsible for testing their end-product for any additional compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or
co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be
used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be
maintained between the antenna and users. The final end product must be labeled in a visible area with the following:
“Contains FCC ID:V5PCM7ABW and IC: 11689A-CM7ABW”.The grantee's FCC ID&IC ID can be used only when all FCC&IC
compliance requirements are met.
Manual InformationTo the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or
remove this RF module in the user’s manual of the end product which integrates this module.The end user
manual shall include all required regulatory information/warning as show in this manual.
Industry Canada statement






This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions:
1) this device may not cause interference, and
2) this device must accept any interference, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes:
1) l'appareil ne doit pas produire de brouillage, et
2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter, except tested built-in radios.
Cet appareil et son antenne ne doivent pas être situés ou fonctionner en conjonction avec une autre antenne ou un
autre émetteur, exception faites des radios intégrées qui ont été testées.
The County Code Selection feature is disabled for products marketed in the US/ Canada.
La fonction de sélection de l'indicatif du pays est désactivée pour les produits commercialisés aux États-Unis et au
Canada.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé.
Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et
votre corps.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : qyb
Company                         : PD
Content Type Id                 : 0x010100685AE5A4E4523B45A3508A2F283C0A6E
Create Date                     : 2017:12:21 17:13:07+08:00
Modify Date                     : 2017:12:21 17:13:08+08:00
Source Modified                 : D:20171221063120
Subject                         : 
Dlc Doc Id                      : VCMYHUY2VMMT-10-182
Dlc Doc Id Item Guid            : 9a5559a3-9e58-4099-b087-92ffa4b3eb15
Dlc Doc Id Url                  : http://paxdata-bj-sps:10001/D900/_layouts/DocIdRedir.aspx?ID=VCMYHUY2VMMT-10-182, VCMYHUY2VMMT-10-182
Language                        : EN-US
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30
Metadata Date                   : 2017:12:21 17:13:08+08:00
Creator Tool                    : Acrobat PDFMaker 15 Word 版
Document ID                     : uuid:69985471-4d9b-484b-a462-79c99f23abdd
Instance ID                     : uuid:9a507318-20f5-4ea3-97c2-1e29534b610f
Format                          : application/pdf
Title                           : 
Description                     : 
Creator                         : qyb
Producer                        : Adobe PDF Library 15.0
Keywords                        : 
Tag dlc Doc Id Item Guid        : 9a5559a3-9e58-4099-b087-92ffa4b3eb15
Tag dlc Doc Id                  : VCMYHUY2VMMT-10-182
Tag dlc Doc Id Url              : http://paxdata-bj-sps:10001/D900/_layouts/DocIdRedir.aspx?ID=VCMYHUY2VMMT-10-182, VCMYHUY2VMMT-10-182
Page Layout                     : OneColumn
Page Count                      : 6
EXIF Metadata provided by EXIF.tools
FCC ID Filing: V5PCM7ABW

Navigation menu