PAX Technology D210WCDMA Wireless POS Terminal User Manual

PAX Technology Limited Wireless POS Terminal

User manual

Wireless POS Terminal D210       PAX TECHNOLOGY LIMITED
1. Installation 1) SAM Card Installation ① Open up battery cover, which is at the bottom of the terminal; ② Take out battery; ③ Insert SAM card to corresponding SAM card slot. 2) Battery Installation ① Hold the battery with its facing up; ② Attach battery forelock to battery bayonet; ③ Press down the other side of the battery 2. Instruction 1) Power ON/OFF Power on: Insert power adapter or insert the battery, Press    button for 3 seconds until LCD backlight is on. If POS terminal is being turned on successfully, PAX LOGO can be seen  and   ‘Di’    from the buzzer can be heard. Power off: Press    button for 3 seconds until Shutting down… can be seen. POS terminal is being turned off. 2) Magnetic Stripe Card When  user  swipes  magnetic  stripe  card  along  the  slot,  the  backside  of  card,  which  contains magnetic strip information, should be facing to the terminal. Bi-directional swiping is supported. It is recommended to swipe starting from the top of the terminal to the bottom of the terminal with a constant moving speed. 3) IC card When  user  insert  IC  card  into  the  IC  slot,  the  chip  of  IC  card  should  be  facing  up;  user  is recommended to gently insert the card, in order to avoid any physical damage to the card or the IC slot of the terminal. If IC card is successfully read by the terminal, the IC card icon will be shown on LCD display screen. 4) Tearing off receipt from the terminal   After the receipt is printed, pinch the end of the receipt and keep an angle of 45 degrees between receipt and the cutter of the terminal; tear off the receipt swiftly. 3. Specifications Default CPU: 32-bit,ARM11 Memory:64MB DDR , 128MB Flash, Micro SD(Maximum 32GB) Display:2.8 -inch 320x240 pixel color TFT LCD;LED backlight; Keypad:10 alphanumeric keys, 8 functional keys Magnetic Card Reader  :Track 1/2/3,bi-directional swipe IC Card Reader:1 user card  (EMV2000) Contactless Reader: 1 Contactless Reader(ISO/IEC 14443 Type A/B) SAM slots:SAM slot 2 or SAM slot 1 Communication:  Bluetooth, WIFI, WCDMA Peripheral  Ports:  1  Mini  USB  Interface  (RS232),  1  Mini  USB  Interface(USB  HOST),1  Power Interface                                 1 Multi-Functional port(High-Speed RS232+Power charge port) Printer : Thermal printer; Speed:18 lines/sec; Paper width:58mm
Paper roll outside diameter: 40mm Power Supply:Input:100-240VAC ~0.3A 50/60HZ Output:9V DC 1A Battery:Li-on battery, 2300mAh, 7.4V Working Environment:  Temperature:-10℃~50℃(32℉~122℉) R.H.: 10%~93%(non-condense) Storage Environment:  Temperature:-20℃  ~ 70℃  (-4℉~158℉) R.H.:5% ~95%(non-condense) Dimensions:166.48mm  80.09mm 52.99mm(L W H) Weight:365g(with Li-on battery)    4. Installation and Usage Tips 1)Do not damage electric wire and power adapter. If electric wire or power adapter is damaged , please do not use the terminal any more. 2) Before power adapter is plugged into power socket, please make sure that voltage which the power socket supplies is appropriate working voltage for the terminal. 3)Do not expose the terminal in sunshine, or in humid, hot, or dusty environment 4)Keep the terminal away from liquid material 5) Do not plug any unknown material into any port of the terminal, since it may create serious damage to the terminal. 6) If the terminal is defective, please contact professional POS repair technicians. 7) When installing paper roll, please be aware of the cutter within paper bracket. 8) Please use standard thermal paper, in order to protect the printer and avoid paper jam. 9) Do not assemble the terminal in explosion hazardous area.  5.Battery Usage Tips 1) Charge indoor by PAX charger, where is cool and well ventilated; 2) Do not apart the battery; 3) Do not short circuit the battery; 4) Keep the battery away from sunshine, smog and dust; 5) Do not squeeze, punch the battery, put it into liquid or near fire; 6) Keep way from environment which is too hot , too cold, damp and highly explosive; 7) Once a failure happens such as heating or distortion, or it was broken down. Please change new battery; 8) Change new battery if it cannot satisfy your requirement; 9) Change new battery if using more than two years. FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:  (1)  This  device  may  not  cause  harmful  interference,  and  (2)  this  device  must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant  to  Part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide  reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause  harmful  interference  to  radio  or  television  reception,  which  can  be  determined  by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Caution:  Changes  or  modifications  not  expressly  approved  by  the  party  responsible  for compliance could void the user‘s authority to operate the equipment. FCC RF Exposure Information (SAR) This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States.    During SAR testing,  this device is set to  transmit at its highest certified power level  in all tested frequency bands, and placed in positions that simulate RF exposure in usage near the body. Although the SAR is determined at the highest certified power level, the actual SAR level  of  the  while  operating  can  be  well  below  the  maximum  value.   This  is  because  the device is designed to operate at multiple power levels so as to use only the power required to reach the network.   In general, the closer you are to a wireless base station antenna, the lower the power output.  The exposure  standard  for  wireless  employs  a  unit  of measurement  known as  the  Specific Absorption Rate, or SAR.   The SAR limit set by the FCC is 1.6W/kg.     The  FCC  has  granted  an  Equipment  Authorization  for this  model  device  with  all reported SAR  levels  evaluated  as  in  compliance  with  the  FCC  RF  exposure  guidelines.   SAR information on this model device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: V5PD210WCDMA.  For this device, the highest reported SAR value for near the body is 1.38W/kg.  While there  may  be  differences between  the SAR levels  of  various devices  and at various positions, they all meet the government requirement.

Navigation menu