PAX Technology D2204GBW Mobile Payment Terminal User Manual D220

PAX Technology Limited Mobile Payment Terminal D220

User manual

D220 Wireless POS Terminal
1. Installation
Micro SAM/SIM Card
a) Remove the bottom cover.
b) Insert the Micro SAM/SIM card to the corresponding card slot.
2. Instructions
1) Power ON/OFF
Power on: Plug in power adapter, Press Power ON/OFF button for 5 seconds, and then PAX
LOGO will display on LCD.
Power off: Press Power ON/OFF button for 3 seconds until Shutting down... can be seen.
Forced shutdownPress Power ON/OFF button more than 6 secondsuntil the screen no
display, that is forced to shut down.
2) IC Card
Put IC card chip side upward, push-in IC card slot and to bottom.
3) Contactless Card
The card read area is above the LCD, Put the card above the LCD.
4) Battery Charge display
Connecting USB port with external adapter can charger battery. And there are charging
display.
5) Battery Charge style
Please use the original adapter instead of pc usb port if you need to charge.
3. Installation and Usage Tips
1Avoid putting the terminal in direct sunlight, high temperature, moist, or dusty environment.
2Forbid non-professional to repair the terminal.
3Before insert the card, please check internal and around of IC card slot. when you found some
suspicious objects , must report to related administrator.
4. Lithium Ion Battery Usage Tips
1) In order to prolong the battery life, the terminal needs to charge at least once in 3 months..
2) Avoid putting the battery in sunlight or smoke, dusty environment.
3) Forbid crushing, treading ,throwing the battery into fire or liquid.
4) Replace the battery immediately if it is damaged(exothermic or distorted).
5) It is recommended changing battery that used more than two years.
5. Specifications
1) CPU 32-bit, ARM Cortex-A9, 1.25 GHz
2) Memory 512MB FLASH, 512MB SDRAM
3) Display 4" TFT, 480 x 800 pixels
4) Keypad Enter, Cancel, Clear (Touch key)
5) 0~9 (Virtual key)
6) Magnetic Card Reader Track 1 / 2 / 3, bi-directional
7) IC Card Reader EMV4.3 L1 & L2 certied
8) SAM Slots 1 Micro SAM Slot, ISO7816
9) Communication 4G / 3G / Bluetooth + WiFi
10) Ports 1Micro USB
11) Battery Li-ion 3050mAh
12) Power Supply Input: 110~240V AC, 50/60Hz
13)
Output: 5V DC, 2A
14)
Working Environment
Temperature: 0°C to 50°C (32°F to 122°F)
15)
R.H. : 10~90( non-condense)
16)
Storage Environment
Temperature: -20°C to 70°C (-4°F to 158°F)
17)
R.H. : 5~95( non-condense)
18)
Dimensions
136.5mm x 70mm x 17.4mm (L x W x H)
19)
Weight
182g with battery
20)
Wireless Module
21)
Operating Frequency Band (RF):
22)
LTE (FDD) B2/B4/B5/B17, all bands with diversity
23) HSDPA/HSPA+/HSUPA/WCDMA B2/B4/B5
24)
Type of ModulationLTE (FDD)
FCC notice
The following statement applies to all products that bear the FCC logo
and/or FCCID on the product label.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This device has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiated radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user‘s authority to operate the equipment.
FCC RF Exposure Information (SAR)
This devices is designed and manufactured not to exceed the emission limits for exposure to radio
frequency (RF) energy set by the Federal Communications Commission of the U.S. Government.
For SAR testing, this device is set to transmit at its highest certified power level in all tested
frequency bands. And placed in position that simulate RF exposure in usage near the body.
Although the SAR is determined at the highest certified power level, the actual SAR level of the
phone while operating can be well below the maximum value. This is because the phone is
designed to operate at multiple power levels so as to use only the power required to reach the
network. In general, the closer you are to a wireless base station, the lower the power output.
The exposure standard for wireless employs a unit of measurement know as the Specific
Absorption Rate. Or SAR. The SAR limit set by the FCC is 1.6W/kg.
The FCC has granted an Equipment Authorization for this model phone with all reported SAR
levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on
this model phone is on file with the FCC and can be found under the Display Grant section of
http://www.fcc.gov/oet/fccid after searching on FCC ID: V5P-D2204GBW
For this device, the highest reported SAR value for usage near the body is 0.95 W/kg.
While there may be differences between the SAR levels of various phones and at various positions,
they all meet the government requirement.
PAX TECHNOLOGY LIMITED
To know more product details, please visit http://www.pax.com.cn
P/N200312000000206

Navigation menu