PAX Technology D900W Mobile payment Terminal User Manual

PAX Technology Limited Mobile payment Terminal

user manual

D900 User ManualD900Mobile Payment TerminalPAX TECHNOLOGY LIMITED
D900 User ManualProduct DescriptionFigure 2: Front view1. Receiver2. LED indicator3. Touch screen4. Android function keys5. USB connector6. Pinpad function keys7. Pinpad screen8. Pinpad keys9. Multi-function connector10. Microphone11. Smart card reader
D900 User ManualFigure 2: Back view1. Magnetic stripe card reader2. Speaker3. Battery compartment cover4. Barcode / Camera5. Audio jack6. POWER key1. Battery slot2. Barcode label3. Nameplate4. MicroSD slot5. SAM2 slot6. SAM1 slot7. Battery8. Battery hook9. Battery compartment coverFigure 3: SIM / SAM card slot & battery
D900 User ManualFigure 4: View from different angles1) SAM CardFigure 5: Take off the battery compartment cover①Take off the battery compartment cover.②Insert SAM card into the slot.2) Battery①Remove the battery compartment cover.②Install the battery.3) MicroSD Card①Take off the battery compartment cover.②Insert MicroSD card into the slot.
D900 User ManualInstructions1) Switch the device on / offSwitch on:Press and hold the POWER button until the device vibrates..Switch off:①Press and hold the POWER button for a few seconds. ②When the menu appears, tap Power off.2) Swipe magnetic stripe cardFigure 6: Swipe magnetic stripe cardWhen users swipe magnetic stripe card along the slot, the back of the card must be faced up asshown in Figure 6. Bi-directional swiping is supported. It is recommended to swipe from the top of theterminal to the bottom with a constantspeed.3) Read IC cardWhen inserting IC card into its slot, the chip of IC card must be faced up. In order to avoid anyphysical damage to the card or the IC slot of the terminal, it is recommended to insert the cardgently. If IC card is successfully detected by the terminal, the icon of the IC card will be shown on thetop of screen.4) Tap contactless cardFigure 7: Tap Contactless Card
D900 User ManualAs shown in Figure 7: when tapping contactless card, please put the contactless card into thesensing area at the back cover of the terminal.4) LED indicatorThe LED indicator show①Solid blue when the system is starting.②Solid red when the battery is being charged.③Solid green when the battery is fully charged.SpecificationsCPU: 800MHz Android application processor (AP)32-bit secure processor (SP)Memory: AP: 512MB FLASH, 512MB DDRSP: 8MBFLASH, 16MB SDRAMDisplay: HVGA (320×480), 3.5"TFTTouch screenKey: 10 alphanumeric keys4 android function keys 3pinpad command keys 3pinpad function keys 1power buttonMagnetic Stripe Card Reader: Encryption transmission, triple track l/2/3, bi-directionalSmart Card Reader: 1 User card (EMV4.3)Contactless(Opt.): ISO14443 Type A & Type B, Mifare, FelicaSAM Slots: 2, ISO7816Camera(Opt.): 5 mega pixel, auto focus, with flashBarcode Scanner(Opt.): 1D barcode scanningCommunication: Wi-Fi 802.11 b/g/nBluetoothPeripheral Ports: 1 RS232 (MiniUSB), 1 USB2.0 (MicroUSB)1 Handset jack, 1 Multi-function extension portBattery: Li-ion battery l850mAh, 3.7VPower Supply: Input: 100-240VAC, 50Hz / 60HzOutput: 5VDC, 1AWorking Environment: Temperature:0℃～50℃(32°F～122°F)R.H.:10％～90％(non-condense)Storage Environment: Temperature:-20℃～70℃(-4°F～158°F)R.H.:5％～95％(non-condense)Dimensions: 137mm×77mm×32mm (L×W×H)Weight: 390g (battery included)
D900 User ManualInstallation and Usage Tips1) Do not damage the power cord and the adapter. If the power cord or the adapter is damaged,please do not use it any more.2) Before the adapter is plugged into the socket. Please make sure that its voltage is appropriatefor the terminal.3) Do not expose the terminal in sunshine, or in humid, hot, and dusty environmental conditions4) Keep the terminal away from liquid materials.5) Do not plug any unknown material into any port of the terminal, since it may cause seriousdamage to the terminal.6) If the terminal is defective, please contact professional POS technicians.7) Do not assemble the terminal in explosive and hazardous area.Battery Usage Tips1) Charge indoor with PAX charger under cool and well ventilated conditions.2) Do not dismantle the battery.3) Do not short-circuit the battery.4) Keep the battery away from sunshine, smog and dust.5) Do not squeeze and punch the battery, and do not put it into liquid or near fire.6) Keep the battery away from environmental conditions which are too hot, cold, damp and highlyexplosive.7) Once a failure happens such as heating or distortion, or it was broken down, please replace itwith a new battery.8) Please replace it with a new battery if the aging phenomenon happens.9) Please replace it with a new one if the battery is used more than two years accumulatively.
FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. RF Exposure Information This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government.

Navigation menu