PAX Technology S80 Payment Terminal User Manual

PAX Technology Limited Payment Terminal Users Manual

Users Manual

Product Description1Product DescriptionFigure 1 Top ViewFigure 2 Bottom ViewFigure 3: SAM/SIM Socket      Figure 4 Ports at BottomFigure 5: S80 Wall Mounting Device          Note: The above figure shows S80 equipped Wall Mounting Device                     which is optional.Installation2Installation1) Place S80 on table2) Connect the attached cableRemove port cover on bottom of S80Connect each plug of the attached cables into the corresponding sockets on the rear panel of the terminal. Put the port cover back.SAM PINPADRS232APowerLINELAN /RS232BSIM3) Insert the telephone cord supplied with the terminal into standard RJ-11 type outlet. Connect the other end of the telephone cord into a standard RJ-11 type modular telephone line outlet.  The figure below shows  cable installation.4) Connect serial facility to RS232 socket.5) Connect AC plug of power adaptor into AC socket.6) Place paper roll into S80     Press the paper cover release key  to open paper cover.     Insert paper roll along the arrow.     Lead the paper out and place the paper on paper cut and        push the paper  cover downward until  a sound of   ka  can Instruction3Instructionbe heard.7) Turn on S80, LCD backlight is on. On screen initialization and application interface show on one after another.8) To perform a simulation of transaction successfully thus S80 installation is OK.1) Power on/offPower on: Press the red button for about 2 seconds until LED backlight on, the POS is on.Power off: Press the red button for about 2 seconds until the content of display vanishes, the POS is off.2) Magnetic swipeWhen pulling a magnetic card along the slot, make the magnetic stripe face the machine. Bi-directional pulling the magnetic card is acceptable. It is recommended from up to down, and with a steady speed.3) IC card operational descriptionWhen insert a card, make the contact of the card upward. Gently insert and withdraw the card In order to protect the contact on card and IC card connector.4) Tear paper operationHold the end of paper along with the paper cut as an angle of 45 degree and swiftly and evenly tear the paper off.POS WallPOSWall Mounting Device Wall Wall Mounting DevicePaper coverLCD displayOn/off KeyPaper cover release keyATM-style keyKeypadIC Card slotPrivacy shield(Opt.)Paper cutterPAX TECHNOLOGY LIMITED reserves the right to change product technology specifications without notifying.Room 2416, 24/F., Sun Hung Kai Centre, 30 Harbour Road, Wanchai, Hong KongTel: +852-2588 8808    Fax: +852-2802 3300E-mail: daniel@pax.com.hk Website: www.pax.com.hkPAX TECHNOLOGY LIMITED®®®Magnetic stripcard slotHang hole(Opt.)Port coverNameplate USB port Bar code lableSAM/SIM socket coverPower Contactless Card ReaderInterfaceScrew
S80S80S80 HandoverCountertop Payment Terminal Installation ManualPAX TECHNOLOGY LIMITEDSpecificationSpecification51) Use a power bar well grounded and with a fuse in it.2) Protect power supply cable and power adaptor. If they are broken, they are no longer be used.3) Before connect power bar to AC socket, make sure the voltage is correct as POS states.4) POS should be placed steady on table. It is not allowed make it under sun beam, high temperature, high humidity or place full of dust.5) Keep it away from liquid.6) Don't insert hard stuff into port which may damage POS severely.7) When a POS is in failure, please contact designated personnel to maintain it. It is not allowed to repair it on your own.8) When insert paper roll, do not touch paper cut and protect your finger from being hurt.9) Only use designated paper roll to avoid paper jam or damaging the printer.Notice at Installation and Use4Notice at Installation and UseDefaultCPU:                            32-bit ,ARM9Memory:                       8MB Flash, 16MB SDRAMDisplay:                        128 x 64 pixel LCD,  LED backlightKeypad:                        10 alphanumeric keys, 8 functional keys,                                    4 ATM keys, 1 switch(on) key                                    ISO7812, Track 1/2/3,                                     bi-directional swipeIC Card Reader:           1, EMV2000 compliantSAM Slots:                   3, ISO7816Modem:                        Sync. ()                                    Async. (V.92,  )Peripheral Ports:          1 RS232, 1 PIN Pad, 1 line port,                                      1 Phone portPrinter:                         Thermal printer, Speed: 20 lines/sec,                                     Paper width: 57mm                                    Paper roll outer diameter: 50mmPower Supply:              Input 100-240VAC, 50Hz/60Hz, 1.5A                                    Output 8.2VDC, 5AWorking Environment:  Temperature:0 40 (                                    R.H. :10% 90%(non-condense)Storage Environment:  Temperature:-20 70 (                                    R.H. :5% 95% non-condenseDimensions:                 216mm  x  95mm  x  86mm  (L  x  W  x  H, including the keypad privacy shield)Weight                       525gOptional:Built-in Ethernet moduleHDLC up to 9600bps,                                      V.21,V.22/V.22bis,V.29up to 56Kbps, 1 USB port32 104 )-4 150 )Built-in GPRS moduleMass storage: 128MBContactless Card Reader (Can connect with an external contactless card reader as an integrated design of POS system. ISO/IEC14443 Type A/B, 4 LEDs RF Indicator)PIN ProtectionPIN ProtectionThe following techniques can be employed to provide for effective screening of the PIN-entry during the PIN entry process. These methods would typically be used in combination, though in some cases a method might be used singly.Positioning of terminal on the check-stand in such way as to make visual observation of the PIN-entry process infeasible. Examples include:Installing PED on an adjustable stand that allows consumers to process difficult.Positioning of in-store security cameras such that the PIN-entry keypad is not visible.Post instructions around check-stand, in order to inform customers. Instructing the cardholder regarding safe PIN-entry. When the cardholder input his/her PIN, he/she had better use his/her body and hands to prevent visual observation of PIN-entry process.-Visual shields designed into the check-stand. The shields may be solely for shielding purposes, or may be part of the general check-stand design, e.g., used as selling area. -Position the PED so that it is angled in such a way to make PIN spying difficult.Note *Customer instruction methods are less repeatable and therefore should be used in combination with other methods. Security levels: L = low M = medium H = highS80 PIN-entry observation corridors v.s. PIN protection methodsCustomersin Queue Cashier  CustomersElsewhere  On-SiteCamera  RemoteCamerasObservation CorridorsMethod S80 on Adjustable StandPost CustomerInstructionS80 in Check-Standwith shieldswivel the terminal sideways and/or tilt it forwards/backwards to a position that makes visual observation of the PIN-entry ® ®®Note To protect the process of PIN-entry, it is not limited to the above methods and examples, merchants also can adopt other methods and steps to keep cardholder's PIN safe.Magnetic Card Reader: CAUTION To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord
Note: RSS232 Port only used as upgraded EUT by manufacturer  Warning: We declare that: ※ The FCC ID label is placed on Payment Terminal clearly visible to all persons at the time of purchase. ※ The user is cautioned that changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.  ※ This device complies with part 15 of the FCC Rules. Operation is subject to the      following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. ※ Do not attempt to disassemble the  Payment Terminal by yourself.Non-experthandling of the devices may damage them. ※ Your  Payment Terminal is a radio transmitter and receiver. It is designed and manufactured not to exceed limits for exposure to radio frequency (RF) energy set by the Federal Communications ※ Commission (FCC) of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age or health. The exposure standard for  Payment Terminal employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limits set by the FCC are 1.6 W/Kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the  Payment Terminal transmitting as its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the  Payment Termina is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station, the lower the output power.  This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .  Note: This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.

Navigation menu