PBE Europe as Axell Wireless A215SERIES Dual Band Repeater MBF-D-8-19 User Manual manual

Axell Wireless Dual Band Repeater MBF-D-8-19 manual

manual

    MBF, Multi Band Repeater                                                            PRODUCT DESCRIPTION AND USER’S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  1 (105)          MBF, Multi Band Repeater Product Description and User’s Manual       This revision of the MBF manual is valid for single, dual and tri band repeaters covering the frequency bands LTE 700, 850, 900, 1800, 1900, 2200 and AWS  Firmware release version  Common Commands and Attributes v 1.3.2  MBF Commands and Attributes v 1.0.0     Copyright © 2010 Axell Wireless Ltd All rights reserved. No part of this document may be copied, distributed, transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language without  the  prior written permission  of Axell  Wireless Ltd. The  manufacturer  has  made  every  effort  to  ensure  that  the  instructions  contained  in  this  document  are adequate and  free  of  errors  and  omissions.  The  manufacturer will, if necessary, explain issues which  may not  be covered by this document. The manufacturer's liability for any errors in  the  document is limited to the correction of errors and the aforementioned advisory services. This  document  has  been  prepared  to  be  used  by  professional  and  properly  trained  personnel,  and  the customer assumes full responsibility when using them. The manufacturer welcomes customer comments as part  of  the  process  of  continual  development  and  improvement  of  the  documentation  in  the  best  way possible  from  the  user's  viewpoint.  Please  submit  your  comments  to  the  nearest  Axell  Wireless  sales representative.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  2 (105)  Table of Contents Safety Instructions and Warnings ................................................................................................. 4 References .................................................................................................................................... 7 Contact Information ..................................................................................................................... 8 Definitions, Abbreviations and Acronyms ................................................................................... 9 1.1 Basic Repeater Features .................................................................................................... 12 1.2 Repeater Types .................................................................................................................. 12 1.3 Repeater Applications ....................................................................................................... 16 2.1 Repeater Firmware ............................................................................................................ 19 2.2 The RMC, Repeater Maintenance Console ....................................................................... 19 2.3 The AEM, Axell Element Manager ................................................................................... 19 3.1 Overview ........................................................................................................................... 20 3.2 Repeater Models ................................................................................................................ 21 3.3 Characteristics ................................................................................................................... 22 3.4 Casing ................................................................................................................................ 22 3.5 Connections ....................................................................................................................... 24 3.6 Building Blocks ................................................................................................................. 24 3.7 Signal Diagrams ................................................................................................................ 30 3.8 OMU-Repeater System ..................................................................................................... 32 3.9 Access to the System ......................................................................................................... 33 3.10 SW for Configuration and Control .................................................................................... 34 4.1 Software Features - Overview ........................................................................................... 35 4.2 Network Nodes .................................................................................................................. 36 4.3 Fibre Loss Compensation .................................................................................................. 38 4.4 Alarm System .................................................................................................................... 39 4.5 Repeater Heartbeat ............................................................................................................ 52 4.6 RF Parameters ................................................................................................................... 57 4.7 Hardware Identification ..................................................................................................... 59 4.8 Tag and ID ......................................................................................................................... 60 4.9 User Access ....................................................................................................................... 61 4.10 Integration into AEM ........................................................................................................ 62 4.11 Upgrading Firmware ......................................................................................................... 62 5.1 Commissioning Advice ..................................................................................................... 64 5.2 Install the Repeater ............................................................................................................ 69 5.3 Start-up the Repeater ......................................................................................................... 78 5.4 Initiate Local Communication ........................................................................................... 82 5.5 Install the OMU and Set up OMU-Repeater System ......................................................... 84 5.6 Configure the Repeater ...................................................................................................... 84
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  3 (105)  5.7 Set Up Remote Communication ........................................................................................ 87 5.8 Integration into the AEM ................................................................................................... 98 6.1 General .............................................................................................................................. 99 6.2 Preventative Maintenance ................................................................................................. 99 6.3 Trouble Shooting ............................................................................................................... 99 6.4 Component Replacement ................................................................................................... 99 6.5 Product Disposal ................................................................................................................ 99 7.1 Single Band Repeater MBF-S-7/8/9/17/18/19/22............................................................ 100 7.2 Dual Band Repeater MBF-D-9-22/8-19/7-17 .................................................................. 102 7.3 Tri Band Repeater MBF-T-9-18-22/8-17-19 ................................................................... 104
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  4 (105)  Safety Instructions and Warnings Guarantees All antennas must be installed with lightning protection. Damage to power modules, as a result of lightning are not covered by the warranty. Switching on AC or DC power prior to the connection of antenna cables is regarded as faulty installation procedure and therefore not covered by the Axell Wireless warranty.  The repeater box should be closed using the two screws. The screws must be fully tightened. Failure to do so may affect the IP65 compliancy and therefore any warranty.  Safety to Personnel Before installing or replacing any of the equipment, the entire manual should be read and understood. The user needs to supply the appropriate AC or DC power to the repeater. Incorrect power settings can damage the repeater and may cause injury to the user. Caution Please be aware that the equipment may, during certain conditions become very warm  and can cause minor injuries if handled without any protection, such as gloves.  Throughout this manual, there are "Caution" warnings. "Caution" calls attention to a procedure or practice, which, if ignored, may result in injury or damage to the system, system component or even the user. Do not perform any procedure preceded by a "Caution" until the described conditions are fully understood and met. Caution This notice calls attention to a procedure or practice that, if ignored,  may result in personal injury or in damage to the system or system component. Do not perform any procedure preceded by a “Caution” until described  conditions are fully understood and met. Safety to Equipment When installing, replacing or using this product, observe all safety precautions during handling and operation. Failure to comply with the following general safety precautions and with specific precautions described elsewhere in this manual violates the safety standards of the design, manufacture, and intended use of this product. Axell Wireless assumes no liability for the customer's failure to comply with these precautions. This entire manual should be read and understood before operating or maintaining the repeater. Electrostatic Sensitivity Observe electrostatic precautionary procedures. Caution ESD = Electrostatic Discharge Sensitive Device  Semiconductor transmitters and receivers provide highly reliable performance when operated in conformity with their intended design. However, a semiconductor may be damaged by an electrostatic discharge inadvertently imposed by careless handling. Static electricity can be conducted to the semiconductor chip from the centre pin of the RF input connector, and through the AC connector pins. When unpacking and otherwise handling the repeater, follow ESD precautionary procedures including use of grounded wrist straps, grounded workbench surfaces, and grounded floor mats.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  5 (105)  Class 1 Laser This product is equipped with class 1 lasers, as per definition in EN 60825-1.  Caution Un-terminated optical receptacles may  emit laser radiation. Do not stare into beam  or view with optical instruments.  Optical transmitters in the opto module can send out high energy invisible laser radiation. There is a risk for permanent damage to the eye.   Always use protective cover on all cables and connectors which are not connected. Never look straight into a fibre cable or a connector. Consider that a fibre can carry transmission in both directions.  During handling of laser cables or connections ensure that the source is switched off. Regard all open connectors with respect and direct them in a safe direction and never towards a reflecting surface. Reflected laser radiation should be regarded as equally hazardous as direct radiation. Radiation Hazard  This equipment emits radio frequency radiation and can, if used the wrong way, be hazardous for personnel. Here follows an example of the power densities from an intentional radiator.  For radiation from a general antenna, the power density (S) at some distance is according to the well-known formula:  For the repeaters described in this handbook the maximum output powers are 5 W for 900 / 1800 MHz and 10 W 2100 MHz. The corresponding power densities using a + 10 dBi antenna as an example at 1 m will be 4 W/ m² for the 900/1800 MHz output and 8 W/ m² for 2100 MHZ output. 1 m distance from the antenna at these frequencies is used as a minimum distance for practical exposure of the public. It is also difficult to have a developed EMF at distances closer than 1 m.  According to R&TTE Health requirements referring to the 1999 Council recommendation, the reference level for the frequency range of 400 – 2000 MHz is f/ 200 W/ m² ( f in MHz ) and above 2 GHz, 10 W/ m².  For the repeaters in this manual the levels are: GSM 900 (960 MHz) = 4.8 W/m² DC 1800 (1880 MHz) = 9.4 W/m² UMTS 2100 (2170 MHz) = 10 W/m². This means that an installation with a +10 dBi antenna does not exceed the basic restriction levels according to the recommendations. For frequencies between 400 and 2000 MHz the ICNIRP occupational guideline level of exposure is f /40 W/m² (f in MHz), and 50 W/m² for frequencies above 2 GHz. The ICNIRP levels for the frequency above bands: GSM 900 (960 MHz) = 24 W/m² DC 1800 (1880 MHz) = 47 W/m² UMTS 2100 (2170 MHz) = 50 W/m². There are no radiation health issues with the above + 10 dBi antenna installations. However, the repeater is marked with radiation hazard warning.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  6 (105)  References This document covers both GSM and WDCMA repeaters. These references are valid for respective repeater type. ETSI TS 25.106    Universal Mobile Telecommunications System (UMTS); UTRA repeater radio transmission and reception 3GPP TS 25.106 version 5.8.0 Release 5)   ETSI TS 25.143    Universal Mobile Telecommunications System (UMTS); UTRA repeater conformance testing (3GPP TS 25.143 version 5.8.0 Release 5) ETSI EN 301 908-3    Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements ETSI EN 301 489-23    Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 23: Specific Conditions for IMT-2000 CDMA Direct Spread (UTRA) Base Station (BS) radio, repeater and ancillary equipment EN 60 950    Information technology equipment - Safety - Part 1: General requirements EN 301 502    Harmonized EN for Global System for Mobile communications (GSM); Base station and Repeater equipment covering essential requirements under article 3.2 of the R&TTE directive (GSM 13.21 version 8.1.2. Release 1999) ETS 300 342-3    Radio Equipment and Systems (RES); Electro-Magnetic Compatibility (EMC) for European Digital Cellular Telecommunications systems. Base Station Radio and ancillary equipment and Repeaters meeting phase 2 GSM requirements. R & TTE Directive: ETS EN 301 502  (ETS EN 300 609-4/GSM 11.26)     Harmonized EN for Global System for Mobile communications (GSM); Base Station and Repeater equipment covering essential requirements under article 3.2 of the R&TTE directive  ETS EN 301 489-8    Electromagnetic Compatibility (EMC) Standard For Radio Equipment And Services; Part 8: Specific Conditions For GSM Base Stations ETS 300 342-3    Electromagnetic Compatibility (EMC) For European Digital Cellular Telecommunications System (GSM 900 MHz and DCS 1 800 MHz); Part 3: Base Station Radio and Ancillary Equipment And Repeaters Meeting Phase 2 GSM Requirements
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  7 (105)  Contact Information Headquarters  Axell Wireless Aerial House  Asheridge Road  Chesham  Buckinghamshire HP5 2QD  United Kingdom   Tel: +44 1494 777000  Fax: +44 1494 777002   Commercial inquiries  info@axellwireless.com Web site  www.axellwireless.com Support issues  support@axellwireless.com Technical Support Line, English speaking  +44 1494 777 777  Contact information for Axell Wireless offices in other countries can be found on our web site, www.axellwireless.com
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  8 (105)  Definitions, Abbreviations and Acronyms AEM   Axell Element Manager A software tool for operation and monitoring a network consisting of Axell Wireless products.  Previous name of this product was Avitec Element Manager. ALC   Automatic Limit Control Antenna   The part of a radio transmission system designed to radiate or receive electromagnetic waves Antenna beamwidth  More properly referred to as the half-power beamwidth, this is the angle of an antenna pattern or beam over which the relative power is at or above 50% of the peak power Antenna directivity  This is the relative gain of the main beam of an antenna pattern to a reference antenna, usually an isotropic or standard dipole Base station   The central radio transmitter/receiver that maintains communications with a mobile radio equipment within a given range BCCH    Broadcast Control Channel BTS   Base Transceiver Station, one part of a base station. A base station is composed of two parts, a Base Transceiver Station (BTS) and a Base Station Control Module (BSC). A base station is often referred to as BTS. The BTS is also sometimes called an RBS or Remote Base Station.  Carrier-to-interference ratio, C/I  The ratio of power in an RF carrier to the interference power in the channel Carrier-to-noise ratio, C/N  The ratio of power in an RF carrier to the noise power in the channel Channel   In all Axell Wireless documentation a channel is the same as a carrier.  Coverage area   The geographical reach of a mobile communications network or system Coverage hole   An area within the radio coverage footprint of a wireless system in which the RF signal level is below the design threshold. Coverage holes are usually caused by physical obstructions such as buildings, foliage, hills, tunnels and indoor parking garages dB   Decibel, A technique for expressing voltage, power, gain, loss or frequency in logarithmic form against a reference.  dBi   Decibels referenced to an isotropic antenna. A technique for expressing a power gain measurement in logarithmic form using a theoretical isotropic antenna as a reference dBm   Decibels referenced to 1 mW. A technique for expressing a power measurement in logarithmic form using 1 mW as a reference. Dead spot   An area within the coverage area of a wireless network in which there is no coverage or transmission falls off. Dead spots are often caused by electronic interference or physical barriers such as hills, tunnels and indoor parking garages. See also coverage area. Distributed antenna system  A type of antenna system that is distributed or remotely located away from the transmitter. Such an antenna or series of antennas can be connected via coaxial
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  9 (105)  cable, leaky feeder or optical fibre link. DL, Downlink    The transmission path from the base station down to the mobile station EAM   External Alarm Messaging EDGE   Enhanced Data for Global Evolution. A technology that gives GSM and TDMA similar capacity to handle services for the third generation of mobile telecom. EDGE was developed to enable the transmission of large amounts of data at a high speed of 384 kilobit per second, or more.  EMC   Electromagnetic Compatibility. The ability of a device or system to function in its intended electromagnetic environment ERP   Effective Radiated Power ETSI   European Telecommunications Standard Institute. The European standardization body for telecommunications GND   Ground Hand-over   The passing of a call signal from one base station to the next as the user moves out of range or the network software re-routes the call ISI   Inter Symbol Interference. An interference effect where energy from prior symbols in a bit stream is present in later symbols. ISI is normally caused by filtering of the data streams LED   Light Emitting Diode Link budget   A calculation involving the gain and loss factors associated with the antennas, transmitters, transmission lines and propagation environment used to determine the maximum distance at which a transmitter and receiver can successfully operate. LMT   Local Maintenance Terminal LNA   Low Noise Amplifier. A receive preamplifier having very low internal noise characteristics.  Logical channel   A communications channel derived from a physical channel. A physical channel, i.e. RF channel, typically carries a data stream that contains several logical channels. These usually include multiple control and traffic channels. LOS   Line of Sight. A description of an unobstructed radio path or link between the transmitting and receiving antennas of a communications system MCPA   Multi Carrier Power Amplifier MS   Mobile Station (e.g. mobile phone) MTBF   Meantime Between Failures NA   Not Applicable NC   Not Connected NF   Noise Figure Noise figure   A figure of merit for receivers and preamplifiers representing the amount of excess noise added to the signal by the amplifier or receiving system itself. The lower the noise figure, the less excess noise is added to the signal ODF   Optical Distribution Frame, used for connection and patching of optical cables OMC   Operations and Maintenance Centre. A location used to operate and maintain a wireless network
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  10 (105)  OMU   Optical Master Unit, translates between RF signals and optical signals so that fibre fed repeaters can be used.  PA   Power Amplifier. A device for taking a low or intermediate-level signal and significantly boosting its power level. A power amplifier is usually the final stage of amplification in a transmitter. PSTN   Public Switched Telephone Network, standard domestic and commercial phone service Radio link   The equipment and transmission path (propagation channel) used to carry on communications. It includes the transmitting system, the propagation channel and receiving system Repeater    A bi-directional Radio Frequency (RF) amplifier that can amplify and transmit a received Mobile Station (MS) signal in the MS transmit band. Simultaneously it amplifies and transmits a received Base Transceiver Station (BTS) RF signal in the BTS transmit band. RF   Radio Frequency, 9 kHz – 300 GHz Designation   Abbreviation   Frequencies Very Low Frequency   VLF   9 kHz - 30 kHz  Low Frequency   LF   30 kHz - 300 kHz  Medium Frequency   MF   300 kHz - 3 MHz  High Frequency   HF   3 MHz - 30 MHz  Very High Frequency   VHF   30 MHz - 300 MHz  Ultra High Frequency   UHF   300 MHz - 3 GHz  Super High Frequency   SHF   3 GHz - 30 GHz  Extremely High Frequency   EHF   30 GHz - 300 GHz   RMC   Repeater Maintenance Console. Software tool to monitor and control Axell Wireless repeaters via local or remote access RS232   Serial interface standard RS485   Serial Interface standard Service area   The specified area over which the operator of a wireless communications network or system provides services Signal-to-interference ratio, S/I  The ratio of power in a signal to the interference power in the channel. The term is usually applied to lower frequency signals, such as voice waveforms, but can also be used to describe the carrier wave. See also carrier-to-interference ratio. Signal-to-noise ratio, S/N, SNR  The ratio of power in a signal to the noise power in the channel. This term is usually applied to lower frequency signals, such as voice waveforms. See also carrier-to-noise ratio SMSC   Short Messaging Service Centre TCH   Traffic Channel. A logical channel that allows the transmission of speech or data. In most second generation systems, the traffic channel can be either full or half-rate Transceiver   A transmitter and receiver contained in one package. A 2-way radio or cell phone is an example of a transceiver Transmitter   Equipment which feeds the radio signal to an antenna, for transmission. It consists of active components such as the mixer, driver and PA and passive components such as the TX filter. Taken together, these components impress a signal onto an RF carrier
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  11 (105)  of the correct frequency by instantaneously adjusting its phase, frequency, or amplitude and provide enough gain to the signal to project it through the ether to its intended target UL, Uplink    The transmission path from the mobile station up to the base station WDM   Wavelength Division Multiplexing. A technology that uses optical signals on different wavelengths to increase the capacity of fibre optic networks in order to handle a number of services simultaneously VSWR   Voltage Standing Wave Ratio
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  12 (105)  1 Repeater Technology 1.1 Basic Repeater Features A basic feature of a mobile communication system is to transmit RF signals between base stations and mobile radio equipment.  When there is a blocking object, such as a mountain or a building, preventing the base station signal to reach the mobile equipment, a repeater can be used to extend the base station’s coverage area.  RepeaterBTS BTSDonor antennaServer antennaUndisturbed transmission Obstacle creating a coverage hole  MS MS In the downlink path (from the base station to the mobile phone) the repeater picks up the signal in the air via a donor antenna, amplifies it and re-transmits it into the desired coverage area via a server antenna. In the uplink path (from the mobile phone to the base station) the repeater receives the signals from mobile transmitters in the covered area and re-transmits them back to the base station. A repeater can work off-air, as the repeater in the example above, or be fed over fibre from an optical master unit, OMU. The OMU taps the signal directly off a base station via a coupler, converts it to light and transmits it to a number of repeaters via fibre. 1.2 Repeater Types 1.2.1 Channel Selective Repeaters Channel selective repeaters are mainly used for coverage of dead zones, shadows, in-building coverage or other areas with inadequate signal strength. The output power of a channel selective repeater is sufficient to cover an area shadowed by a building or other obstacle.  In a channel selective repeater each carrier is separately filtered, amplified and retransmitted.  BTSDonor antennaServer antennaF1 F1 F1RepeaterMS  A channel selective repeater system consists of one repeater unit complemented with one antenna facing the donor BTS and another antenna directed towards the coverage area. The repeater site needs to be located
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  13 (105)  where the BTS signal strength is large enough to be usable by the system. Ideally the repeater’s donor antenna should have line of sight (LOS) contact with the BTS antenna. If the signal strength is high enough, LOS may in some cases not be necessary. The signal generated by the BTS is picked up at the repeater site via the donor antenna. The repeater filters and amplifies the signal before retransmitting it at the same frequency over the server antenna.  The isolation between the antennas at the repeater site has to be high in order to prevent degradation of signal quality and risk of oscillation. Ways to achieve this can be large physical separation between the antennas, usage of highly directional antennas with good front-to-interference ratio or external shielding between the antennas. Another option is to use a Frequency Translating repeater (see description below). Channel selective repeaters may have higher output power per carrier and typically have better spurious rejection than band selective repeaters. The maximum output power per carrier can be several watts. 1.2.2 Band Selective Repeaters Band selective repeaters have the same functionality as channel selective repeaters. The difference is that band selective repeaters do not separate out specific carriers but amplify and retransmit all signals within a defined frequency band.  The risk for intermodulation distortion leads in most cases to a lower output power per carrier in a band selective repeater than in a channel selective repeater. 1.2.3 Frequency Translating Repeaters A frequency translating repeater provides output power levels comparable to a base station. The concept allows for high gain without the high antenna isolation required for channel selective repeaters. The frequency translating repeater consists of two units; one donor unit and one remote unit.  Donor Cell Base StationRemote unitServer antennaF4 F4 F1Donor unitRF Link PathF1Link antennasRepeater units  The donor unit is mounted at the base station site where the signal enters the repeater via a directional coupler. In the donor unit, the signal is translated into another frequency, the link frequency, amplified and transmitted via a link antenna. At the remote site, a link antenna picks up the signal and feeds it to the remote unit. The signal is translated back into the original frequency and retransmitted over the server antenna.  Only 2 guard channels are needed between the radio frequency and the link frequency.  The isolation between antennas at the remote site seldom needs to be more than 75dB. This value that can be achieved with a limited antenna displacement, often as low as 3 meters. The relatively modest isolation requirement allows the use of omni-directional antennas for the service area. Important applications for frequency translating repeaters are road coverage, rural coverage or for transferring capacity from a base station to another area.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  14 (105)  1.2.3.1 Donor Unit There are two types of donor units – single donor (SD) and double donor (DD).  A single donor (SD) unit has one input connector. The input signal from the BTS is split in two within the repeater unit. In the opposite direction – in the uplink – the signals are combined within the repeater before being sent to the BTS. A double donor (DD) unit has dual inputs. This can be used in combination with a BTS that uses air combining, and hence has a separate antenna for each TRU. A double donor unit can alternatively handle two signals from two separate BTS. 1.2.3.2 Remote Unit There are two types of remote units – internal combining (IR) and external combining (ER). In an internal combining (IR) remote unit output from the power amplifiers in the downlink is combined and filtered before being passed on to the server antenna. In the uplink the signal is separated within the remote unit. An external combining remote (ER) unit has two server antenna ports and the signal is combined in the air. Since the ER model needs no combiner the output signal and gain is 3dB higher than in the IR model. 1.2.4 Band Shifting Repeaters Band shifting repeaters are based on the same concept as frequency translating repeaters described above.  In contrast to a frequency translating repeater, which uses another frequency within the same band for the link, a band shifting repeater uses another band. For instance can a repeater operating on the 900MHz band use the 1800MHz band for the link and vice versa. Other combinations are also possible.  Donor Cell Base StationRemote unitServer antennaBand 2 Band 2 Band 1Donor unitRF Link PathBand 1Link antennasRepeater unitsLink and server antenna on the remote site can often be combined  By using another band for the link the isolation between antennas at the remote site becomes very low. It might in some applications even be possible to use the same antenna for both the link and the service area.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  15 (105)  1.2.5 Fiber Fed Repeaters The fiber fed repeater is primarily designed for coverage of tunnels and large buildings.  BTS BTSLeaky feeder Fiber fed repeatersTunnelHUB/OptoBoxDirectional couplerOptic fiber  A fiber fed repeater can be either channel selective or band selective. It receives the RF signals from the base station via a HUB or an OptoBox which translates the RF signal to an optical signal and sends it to the repeater via a fiber optic cable. The repeater unit can be installed up to 20 km away from the base station. Inside the tunnel leaky feeders or antennas can be used for transmission to the mobile units.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  16 (105)  1.3 Repeater Applications 1.3.1 Channel Selective Repeaters 1.3.1.1 Shadow Coverage and Gap Filling When there are coverage holes caused by buildings or mountains, a channel selective repeater can be used to extend coverage into the “dead zone”. The building can sometimes be used as physical shield to create the necessary antenna isolation.   BTSRepeaterRepeaterMSMS  The terrain is often seen as a limiting factor when striving for flawless radio coverage. The gap-filler repeaters can be used as a complement to the network of base stations. 1.3.2 Frequency Translating Repeaters 1.3.2.1 Low Traffic Coverage   The example shows coverage extension in an area with low traffic by using frequency translating repeaters.  A two sector BTS is extended with two frequency translating repeaters. Both donor units are mounted at the base station site and connected to the base station via directional couplers.  Each repeater has a different link frequency and transmits the frequency of the opposite base station sector, thus minimizing interference or multi-path propagation problems. A normal handover is performed between the repeater coverage area and the neighboring base station coverage area.  BTSDonor unitDonor unitRemote unitRemote unitRF Link PathsF1F1F2F8F2F4F4F8 Since the installation of frequency translating repeaters requires moderate antenna isolation, remote site requirements are very moderate.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  17 (105)  1.3.2.2 Highway Coverage One two-sector BTS feeds two frequency translating repeaters, each covering an area comparable to the base station. This is a way to get maximum coverage out of the one BTS, with one connection point for transmission.  BTS  Since antenna isolation requirements are low for frequency translating repeaters, omni-directional antennas can be used at the remote sites to achieve good coverage. 1.3.2.3 “Fake site” – Moving Capacity In this application the BTS is upgraded with an additional “sector” used for feeding a frequency translating repeater to cover an area up to 20km away from the BTS. This is an effective alternative when no transmission point is available in the area to be covered. The frequency translating repeater “moves” capacity from the base station site to the new location.   BTSRemote unitDonor unitFake Site  This type of installation takes full advantage of the high output power and high sensitivity of the frequency translating repeater. 1.3.3 Band Shifting Repeaters A band shifting repeater can be used in the same way as a frequency translating repeater if the user has access to frequencies on two different bands. 1.3.4 Fiber Fed Repeaters 1.3.4.1 Tunnel Coverage  Fiber optic fed repeaters makes it possible to cover long tunnels from one or two BTS sites nearby. The hub unit at the BTS site can feed up to 24 repeaters. The repeaters distribute the signal in the tunnel with antennas or radiating cables (leaky feeders).
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  18 (105)  Using leaky feeders is normally the most effective way to cover a tunnel, since the signal is evenly distributed along the tunnel. Achieving good coverage in a train tunnel, for instance, using antennas can be difficult as the trains tend to block signal propagation.  1.3.4.2 Open Area Coverage A fiber optic fed repeater can be used in combination with a HUB or an OptoBox to move the repeater away from the base station. This can in some cases be used to avoid antenna isolation problems.  BTSHUB/OptoBoxFiber Fed RepeaterOptical FiberOmnidirectionalAntennaDirectional Coupler  In this example a HUB/OptoBox is placed at the BTS site. The RF signal is tapped from the antenna by a directional coupler, translated into an optical signal and sent to the repeater over a fiber optic link. At the repeater site a fiber fed repeater receives the signal, translates it back to RF and sends it to the antenna. This antenna can be for instance omni-directional because the distance to the BTS is no longer a problem.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  19 (105)  2 Software Overview Axell Wireless mainly supplies three different types of software; Repeater firmware, Repeater Maintenance Console and Axell Element Manager. 2.1 Repeater Firmware The repeater firmware is the software inside the Control Module of the repeater. It is command line based, with simple SET and GET commands. A rich variety of commands are available to control and monitor all subsystems of the repeater from a normal VT100 terminal emulation program, such as MiniCom (Linux/Unix) or HyperTerminal (Windows). This also means that any standard laptop is able to control a repeater without additional software installed. The repeater firmware has three main tasks:  Set and configure parameters in the repeater, such as channel numbers, gain, power levels, and different report configurations  Monitor and measure alarm sources, alarm parameters and repeater utilization  Send reports and alarms to the repeater OMC Communication with the repeater can be performed either locally on site or remotely via a built in modem.  For local communication a terminal with RS232 interface is needed. For remote communication a computer with a modem is needed as well as a serial communications program such as HyperTerminal™. 2.2 The RMC, Repeater Maintenance Console  RMC is an online software program with an intuitive graphical interface that simplifies control and installation of the repeater or OMU. The RMC is a graphical shell for the repeater’s Control Module. It reads commands and attributes from the Control Module and displays them in an intuitive layout. This eliminates the need to learn commands and attributes for controlling the repeater or OMU. Login can be made locally via the LMT port or remotely via a modem or via Ethernet. As soon as the RMC is connected it constantly polls the repeater or OMU for parameters such as power supply levels, in and out levels, temperature, traffic, etc. If the repeater is a slave type repeater, the OMU manages the data collection from the repeater. The RMC program can be installed from a CD. It is a Windows based application that runs on Windows 2000 and Windows XP. 2.3 The AEM, Axell Element Manager AEM is a complete operations and maintenance centre for Axell Wireless repeater networks. The AEM takes control of the repeater – or the OMU-Repeater system - once the installation at site is completed. The repeater gets integrated into the network and will be controlled by the Element Manager. During integration all repeater parameters and statuses are downloaded into a database. The database is regularly updated with all incoming alarms and reports, and will hence contain a copy of the repeater configuration so that current repeater information will be accessible without setting up communication with the repeaters.   Communication between the AEM and the repeaters are message based. This means that the operator does not have to await message delivery, but will be informed when the message is delivered to the repeater The Axell Element Manager is a Windows™ based application that runs on Windows 2000, Windows 2003 Server and Windows XP. For more information please refer to the separate AEM User’s Manual.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  20 (105)  3 Product and System Description  3.1 Overview The MBF family of repeaters include band selective, fibre fed repeaters with one, two or three bands integrated into one repeater box. The repeaters are named MBF (Multi Band Fibre) with an extension that defines the number of bands and the type of band. The number of bands is indicated by a letter where “S” stands for single band, “D” for dual band and “T” for tri band. The frequencies covered are indicated by numbers where “7” stands for 700MHz, “8” stands for 850MHz, “9” for 900 MHz, “18” for 1800MHz, “19” for 1900 MHz, “22” for 2100MHz and “17” for the AWS band. The MBF repeater is a systems component and needs to be fed from an Optical Master Unit, OMU. Each OMU can be equipped with up to 6 fibre optic converters. Several OMUs can also be cascaded to form more extensive repeater systems.  RFMBF RepeaterOpto FiberRFFiberOpticConvertersServer AntennaFrom BTS via couplerOMU Standard OMU-Repeater application where one OMU is used  In a standard OMU-Repeater application as illustrated above, the input signal to the system is tapped off a base station via a directional coupler. In the OMU the RF signal is converted into an analogue optical signal and transported via optic fibre to the fibre fed repeater MBF. The repeater converts the optical signal back into an RF signal which is then amplified and transmitted via a server antenna. In the uplink direction the OMU receives the signal from the repeater via the fibre optical cable, converts it to an RF signal and sends it back to the base station via the coupler. The OMU-Repeater system can also be fed from one a repeater. In this case the signal is tapped from the repeater’s server antenna port. The repeater in its turn can be linked to an antenna that picks up the signal off air. An MBF repeater with more that one band can be equipped with one fibre optic converter which is shared between the bands or have one converter for each band. Below are the two options exemplified. BTS 1BTS 2BTS 3Tri band repeater with three fibre optic convertersServer Antenna A tri band repeater with three fibre optic converters fed by three OMUs
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  21 (105)  BTS 1BTS 2BTS 3Tri band repeater with one fibre optic converterServer AntennaCombiner system A tri band repeater with one fibre optic converter fed by one OMU  An OMU-Repeater system can be expanded to handle up to 24 repeaters and cover a distance of to up to 20 km of fibre between the OMU and the most distant repeater.  3.2 Repeater Models The MBF repeater can be configured in many combinations. These are the most common ones. Single Band MBF-S-7  LTE-700 MBF-S-8   GSM/WCDMA850 MBF-S-9  E-GSM MBF-S-18  GSM1800 MBF-S-19  GSM/WCDMA1900 MBF-S-22  WCDMA2100  Dual Band MBF-D-9-22  E-GSM and WCDMA2100 MBF-D-8-19  GSM/WCDMA850 and GSM/WCDMA1900 MBF-D-7-17  LTE700 and AWS  Tri Band MBF-T-9-18-22  E-GSM, GSM1800 and WCDMA2100 MBF-T-8-17-19  GSM/WCDMA850, AWS and GSM/WCDMA1900
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  22 (105)  3.3 Characteristics  These are some of the most important characteristics of the MBF family of repeaters. For more detailed information please refer to section 7 Specifications. MBF System  GSM/WCDMA850, E-GSM, GSM1800, GSM/WCDMA1900, AWS, LTE and WCDMA2100 Composite Output Power DL  850MHz  +37 dBm Composite Output Power DL E-GSM    +37 dBm* Composite Output Power DL 700MHz  +37dBm Composite Output Power DL 1800MHz  +37 dBm* Composite Output Power DL 1900MHz  +37 dBm Composite Output Power DL 2100MHz  +39 dBm Gain is defined by the whole link including the OMU  Adjustable in 1dB steps  * Note! In repeaters that share a common downlink fibre for 900MHZ and 1800MHz a minimum of 4 carriers in each band is required for the full composite output power to be attainable maintaining full ETSI compliance. 3.4 Casing Axell Wireless repeaters are relatively small and have low power consumption. They are housed in a die cast aluminum box which makes them light and offers good heat conduction and waterproofing. Cooling is accomplished by convection.  Note! The MBF repeaters are designed primarily for multi carrier purposes. If the repeaters are run at full output power over a longer period the convection cooling might not be enough. The repeaters have a power management function implemented that will step down the power and if needed fully shut down the amplifier chains until temperature has reached normal values. In situations where a repeater will be run in such a manner extra cooling can be provided for instance by putting the repeater in a temperature controlled environment or via external fans. The housing conforms to IP65 and NEMA 4 standards.  Dimensions, Weight and Power Consumption Dimensions  Single and dual band versions: 540 x 350 x 150 mm Tri band version:540 x 350 x 220 mm Weight  Single band version: 21 kg, Dual band version: 25 kg, Tri band version: 33kg
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  23 (105)    Single or dual band repeater   Tri band repeater       Single band repeater with door open  Dual band repeater with door open    Tri band repeater with door open
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  24 (105)  The repeaters are closed with two hex screws, M8.  As a complement the repeaters can be locked with a key. Note! The two screws must be fully tightened. Failure to do so may affect the IP65 compliancy and therefore any warranty.  The external connections at the bottom of the repeater can be protected with a cover which is screwed in place.  ScrewsConnectorsLock The repeaters are designed to be mounted on a wall or in a 19” rack. They should always be mounted in a vertical position with the connectors facing downwards. 3.5 Connections All connections are placed at the bottom panel of the repeater.   Power Fiber inputGround Server antennaExternal alarms       Antenna connection is DIN 7/16” connector, female  Fibre connector is SC/APC. It is placed on the fibre optic converter(s) inside the repeater  Plinth connection for power input is described in section 5 Installation  Plinth connector for external alarms is described in section 5 Installation  Note! APC connectors need to be used  throughout the whole link between the OMU and the repeater.  Also all ODF connections need to be of the same type.   3.6 Building Blocks The repeaters consist of the following main building blocks.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  25 (105)   Control Module – all MBF repeaters have one Control Module  MCPA, Multi Carrier Power Amplifier – an MBF repeater has one MCPA for each band   Radio Module – an MBF repeater has one Radio Module for each band   Fibre Optic Converter – an MBF repeater can have one, two or three Fibre Optic Converters  Filter – all MBF repeaters have one filter for one, two or thee bands  RefGen, Reference Generator - all MBF  repeaters have one RefGen  EAIM, External Alarm Interface Module - all MBF  repeaters have one EAIM  PSUP, Power Supply Module  - single and dual band repeaters have one PSUP, and tri band repeaters have two  The illustration to the right shows a dual band repeater with one fibre optic converter.     Radio ModuleExternal AlarmsPower Server Antenna PortPSUPPSUPControl ModuleRef GenEAIMFiber InputFibre Optic ConverterMCPA MCPAFilterRadio Module
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  26 (105)   The illustration to the left shows a tri band repeater with three fibre optic converters                  Radio ModuleExternal AlarmsPower Server Antenna PortPSUPPSUPControl ModuleRef GenEAIMFiber InputFibre Optic ConverterMCPA MCPAFilterRadio ModulePSUPPSUPMCPARadio ModuleFibre Optic Converter Fibre Optic Converter 3.6.1 Control Module The Control Module manages and controls the repeater and handles alarms. The Control Module keeps track of all modules in the repeater based on serial numbers. Data is collected from modules within the repeater such as MCPA, Radio Module and Fibre Optic Converter. The collected data is processed and if an error is detected the Control Module may send an alarm via a built in modem or via Ethernet to an Operations and Maintenance Center (OMC).  In addition to collecting data from all modules, the Control Module can also collect status of four external alarm inputs connected to the External Interface board. The summary alarm status of the repeater can be indicated on a relay port, available on the external interface connector. This relay can be used to indicate to external equipment if the repeater is functioning properly.  The Control Module includes a Real Time Clock (RTC). The RTC keeps track of at what time alarms and events occur. This RTC has its own backup battery in order to keep up proper time keeping even during long power failures.  The Control Module contains a RS232 port used for local access to the repeater. The USB connector is not activated in this version of the repeater and cannot be used.  The Control Module can be configured in two different modes:  Stand-alone Mode – in this mode all communication is made directly with the unit – either locally or remotely via a modem or Ethernet. The communication with the Axell Element Manager is performed using a modem or Ethernet.  Systems Slave – being a systems slave means all communications with the Axell Element Manager is handled by the Control module in the OMU.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  27 (105)  The Control Module has four LEDs which give information regarding the status of the repeater and if someone is logged on to the repeater. If the repeater is configured as a system slave the two LEDs MDM Power and MDM Status do not fill any function and can be disregarded.        LOGINSTATUSMDM PWRMDM STATUS  Blue LED - Login  Quick flash  Control Module switched on, someone logged in locally and/or remotely  Off (except for a quick flash every 10th second) Control Module switched on, no one logged in   Off  (permanent)  Control Module switched OFF  Red LED - Status  Quick flash  Control Module switched on, one or more errors/alarms detected  Off (except for a quick flash every 10th second) Control Module switched on, status OK  Off (permanent)  Control Module switched off   Green LED – Modem Status  On    Depending on type of call: Voice call: Connected to remote party Data call: Connected to remote party or exchange of parameters while setting up or disconnecting a call  Flashing  (irregular) Indicates GPSR data transfer. When a GPRS transfer is in progress the LED goes on within 1 second after data packets were exchanged. Flash duration in approximately 0.5s.  75ms on/75ms off/75ms on/3s off  One or more GPRS contexts activated  75ms on/3s off  Logged to network (monitoring control channels and user interactions). No call in progress  600ms on/600ms off  No SIM card inserted, or no PIN entered, or network search in progress, or ongoing user authentications, or network login in progress  Off  Modem is off Green LED – Modem Power  On  Modem Power is on  Off  Modem Power is off
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  28 (105)  3.6.1.1 Modem The repeater can be equipped with a wireless modem or a PSTN modem for remote control and supervision. Different wireless modem types are supported – GSM, EDGE, GPRS, TETRA, etc. If the repeater is equipped with a wireless modem a SIM card holder is mounted on the Control Module. The repeater can also be accessed via Ethernet. Wireless modems are placed on the Control Module inside the repeater. A PSTN modem is placed in a separate module within the repeater.  3.6.2 MCPA, Multi Carrier Power Amplifier There is one MCPA for each band in the repeater. 3.6.3 Radio Module There is one Radio Module for each band in the repeater. These are RF boards containing two RF-chains, one uplink and one downlink.  3.6.4 Fibre Optic Converter A single band MBF repeater has only one Fibre Optic Converter. A dual or tri band repeater can have one, two or three converters depending on the mixture of frequency bands and the requirements on the system.  The Fibre Optic Converters contain both a receiver and a transmitter. The two optical signals are combined utilizing WDM technology (Wavelength Division Multiplexing). Hence only one fibre is necessary for transmission. The module also contains a function for the internal communication over the fibre.  The Fibre Optic Modules work in pairs in the system – one in the OMU and one in the repeater. The one placed in the OMU is the master (Optical Master Unit) and the one placed in the repeater is the slave (Optical Slave Unit).  The Fibre Optic Converter has a pilot tone generator that is used for detecting the optical path loss in the fibre. This information can be used for compensation of this loss. Optical loss compensation is always initiated from the Optical Master Unit. In the Optical Slave Unit the pilot tone is normally disabled, and only enabled upon request (from for example the Optical Master Unit). The Fibre Optic Converter contains two optical alarm sources. These are alarms for transmitted and received optical signal level. The levels of the received optical signals can be monitored on-line via the RMC. This is convenient during installation and tuning of the system. The module also has two alarm sources for the communication between the master and the slave. There are 6 LEDs on the module to indicate the status.           PWRERRUL DataDL DataOpto RxOpto Tx LED 1, Power, Green  On  Unit is powered on Off  Unit has no power LED 2, Error, Red On  Error detected Off  No error LED 3, UL Data, Yellow On  Communication is ongoing in the uplink direction
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  29 (105)  Off  No communication LED 4, DL Data, Yellow On  Communication is ongoing in the downlink direction Off  No communication LED 5, Opto Rx, Green On  Received RF signal on fiber channel is above threshold Off  Input level below threshold LED 6, Opto Tx, Green On  Transmitted RF signal on fiber channel is above threshold Off  Output level below threshold  3.6.5 Filter The filter provides a wide band selective window for the uplink and downlink in each band on the RF antenna end of the repeater.  3.6.6 RefGen, Reference Generator Module The Reference Generator generates a stable reference frequency which is distributed to the radio modules of the system. It is used as a reference signal in the synthesizer in the repeater and also in the microcontrollers in the MCPA and Radio Module.  3.6.7 EAIM, External Alarm and Interface Module Four external alarm sources can be connected to the alarm module, EAIM. These sources must generate a voltage between 12 and 24 VDC. The presence or absence of this voltage will trigger the alarm depending on how alarm thresholds have been configured in the controller software. The module can also supply +15V to external alarm sources. The maximum allowed load on this supply is 100mA. One relay contact closure is provided to reflect the status of the repeater. This can be used as a sum alarm. For installation of external alarms see section 5 Installation. 3.6.8 PSUP, Power Supply The PSUP is fed by 110/230 V AC, 50/60 Hz or -48 V DC. The PSUP generates secondary DC voltages for the repeater modules. The input is equipped with a surge, EMI, EMC suppression filter.  The -48VDC version of the power supply is designed to turn off if the supply voltage falls below -36V (±1V). It will turn on again as the supply voltage reaches -43V (± 1V). On the Power Supply unit a rechargeable battery pack in mounted. This part also includes charging and supervision electronics. The backup battery will provide the Control Module and modem with enough capacity to send an alarm in case of input power failure.  The power supply module is connected to all other electronic modules via the distribution board. The power supply has a switch which allows it to be set in “on” position or in “stand by”. The battery can be switched on and off.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  30 (105)   Power Supply  The power supply has 4 LEDs to indicate the status. Input Power+6V +15V +28V LED 1, Input Power, Green  Slow flash  Power supply unit operating on AC or DC OFF  Power supply unit not operating LED 2, +6V, Red Slow flash (every 10 seconds)  +6V power supply operating Quick flash  +6V power supply not operating or operating with malfunction LED 3, +15V, Red  Slow flash (every 10 seconds)  +15V power supply operating Quick flash  +15V power supply not operating or operating with malfunction LED 4, +28V, Red Slow flash (every 10 seconds)  +28V power supply operating Quick flash  +28V power supply not operating or operating with malfunction   3.7 Signal Diagrams   Duplex FilterRFOOpticalIn/OutDownlinkRF in/outFiber OpticConverterRadio Module GSMMCPA GSMUplink~~~~~~~~~~~~ Single band repeater for E-GSM
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  31 (105)  MCPA UMTS2 x Duplex FilterRFOOpticalIn/OutDownlinkUplinkRF in/outFiber OpticConverterRadio Module UMTSRadio Module GSMMCPA GSMDownlinkUplink~~~~~~~~~~~~~~~~~~~~~~~~ Dual band repeater for E-GSM and UMTS  In the downlink the signal from the OMU enters the fibre optic converter in the repeater that translates the optical signal to RF. The signal is fed to the Radio Modules. The signals are amplified in the Radio Modules and further in the separate MCPAs. It is then fed to the combined duplex filter and out on the server port to the antenna. In the uplink the signal is amplified in the Radio Modules and translated to an optical signal and fed back to the OMU.  A tri band repeater works in a corresponding way.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  32 (105)  3.8 OMU-Repeater System An OMU-Repeater system consists of one or more Optical Master Units and one or several fibre fed repeaters.  An Optical Master Unit, OMU, can be equipped with up to 6 fibre optic converters. If more than 6 repeaters are needed in the network there are two ways of expanding the system.  Link several OMUs together.   Up to 4 OMUs can be cascaded in this manner, and operate up to 24 repeaters as one system. When OMUs are cascaded only one is equipped with a Control Module and that one manages the other OMUs as well as all the repeaters.    BTSRepeatersOMU Units Four OMUs cascaded in one system   A laser system with two colors can operate one repeater for each fibre optic converter in an OMU-Repeater system; one color is used for the uplink and one for the downlink. A laser system with three or four colors can operate two or three repeaters per fibre optic converter. One color is used for the downlink which is the same for all repeaters, and in the uplink each repeater uses its own color.   The connection from one repeater to the next is done via so called add-drop couplers. If needed these couplers can be designed to balance the downlink signal to compensate for different distances to the repeaters.        Add-drop CouplerSlave 1 Slave 2OMU13101550 1510 Two repeaters are connected to the same converter in the OMU via the same fibre but the wavelength for the uplink differs between the units. Slave 1: 1550 ± 3 nm, Slave 2: 1510 ± 3 nm. The downlink signal is the same for both repeaters.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  33 (105)  3.9 Access to the System Important Generic Information Axell Wireless repeaters and OMUs can be configured in three different ways as regards communication and control. They can be “stand-alone units”, “node masters” or “slaves”. Stand-alone units do not control any other unit or take control from any other unit. All communication with a stand-alone unit needs to be made directly with the unit – either locally or remotely via a modem or Ethernet. Most stand-alone units are equipped with Ethernet and/or a modem for this purpose. Node Masters keep track of the slaves that are connected to it. It is the single point of contact for alarm reports and for heart beats in the entire system, and communicates with the AEM. All configuration and control of all units in the network go through this Node Master. Most stand-alone units are equipped with Ethernet and/or a modem for this purpose. Slaves are linked to a node master. Slaves do not have modems but instead all data is transferred to the master where it is distributed further to the AEM.   An OMU-Repeater system can be designed using repeaters that operate as slaves to the OMU or as stand alone units regarding communication, configuration, alarms etc. Either all communication is handled by the OMU that acts as a node master and the repeaters are slaves, or each repeater (and the OMU) handles this communications and reporting separately.  The most common configuration is the master-slave set up which has several advantages:  All nodes can be reached from any node in the system. An operator can log in from any node in the system and access all parameters in all nodes, including those in the OMU  Only one modem is needed for remote communication and configuration of the whole system  Since the communication runs on the same fibre as the RF, this arrangement gives a reliable supervision of the radio link. If communication between the OMU and a repeater is broken, an alarm can be generated immediately. Several users at a time can be logged on to the system, for instance one locally via the RS232 interface and one remotely via modem or Ethernet. Only one user at a time can be logged in remotely. Note! If the network has an OMU from an earlier generation1, there are some limitations of what can be accessed via a local login to a slave repeater. 3.9.1 Local Access Local access is achieved via a RS232 interface to the LMT port in the repeater or the OMU. This port is accessible on the front of the OMU and inside the repeater.  3.9.2 Remote Access Remote access is achieved via modem or via Ethernet. Different types of modems are supported, for example GSM, GSM-R and PSTN.  The modem is either placed on the Control Module or as a separate unit. When cascaded OMUs are used, the modem is placed in the OMU unit that holds the Control Module. Ethernet connection is available on the Control Module.                                                            1 The earlier version of the OMU was called HUB.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  34 (105)  3.10 SW for Configuration and Control There are two SW tools for configuration and control of the Axell Wireless OMU-Repeater system. The RMC, Repeater Maintenance Consol and the AEM, Axell Wireless Element Manger.  The RMC is an on-line tool that can be used locally or remotely for configuration and monitoring of all parameters in the system. It is installed on a lap-top computer and holds pre-configured screens for each repeater type or OMU that shows the parameters live in a user-friendly manner. All parameters can be accessed and changed on-line. In the RMC there is also a terminal mode that allows for command based communication.  The AEM is a tool for monitoring and control of a whole network. Data from the network elements are collected at regular intervals and alarm information are sent to the AEM as they occur. All data are stored in a data base and can be presented in maps, reports and diagrams.   OMU RepeatersAEM or RMC for remote monitoring via modem or Ethernet RMC for local accessModemGSM, PSTN or TCP/IPdata connection
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  35 (105)  4 Monitoring and Control The MBF repeater can be accessed on site through the Local Maintenance Terminal (LMT) port or remotely over a built in modem or Ethernet in the OMU (for slave-type repeaters) or via a modem or Ethernet in the repeater.  When an RS232 cable is plugged in to the LMT port, there are two options for communication; terminal mode or RMC mode.  Terminal mode is accessed by using a terminal emulation software, such as HyperTerminal™ or ProComm™. Settings should be ANSI or VT100 emulation, baud rate 9600, 8 data bits, 1 stop bit, No parity and No flow control. A simple command language is used to control the repeater in this mode.  Repeater Maintenance Console (RMC) mode allows configuration and control of the repeater via a user friendly Windows software. Note! All instructions in this chapter assumes that the repeater is controlled using the Repeater Maintenance Console, RMC.  For use of the terminal mode please refer to the documents “Common Commands and Attributes” and “MBF Commands and Attributes” which contain detailed description of all attributes and commands. Firmware Documentation Structure The attached documents “Common Commands and Attributes” and “MBF Commands and Attributes” together describe all functionality in the repeater. The Common part contains functionality that is common for all Axell Wireless repeaters of the latest generation and the MBF part contains functionality that is specific for this repeater type. Help Functions When being logged in to a unit using the terminal mode the command  HELP  will list all attributes and their modes of operation and display them in alphabetic order on the screen.  Further help regarding specific commands can be had by typing  INF <command> The INF attribute gives detailed information about a specific attribute. 4.1 Software Features - Overview The firmware in the repeater controls and monitors all repeater parameters. Statuses and measured levels can be read online via the RMC. This includes for instance voltage levels, RF-levels and temperatures. In the event of a failure, an alarm is logged in the repeater. If the repeater is controlled by the AEM, the alarm is also transmitted to the AEM. The repeater can be configured to handle alarms concerning a number of different parameters. Each alarm can also be individually configured in a number of ways. The repeater stores approximately 2 000 alarms in a local alarm log. The data stored regarding each alarm is the time at which an alarm occurred and the alarm information which consists of alarm source, alarm severity, alarm attributes and in some cases an additional alarm description. On regular intervals, the repeater can send a heartbeat report to the AEM to confirm that the repeater is functioning. The heartbeat message contains information about the RF-configuration and the alarm sources. It ensures that the data communication from the repeater to the AEM is working properly. The latest 2 000 heartbeats (approximately) are stored in a log. The Control Module keeps track of the exact repeater type it is controlling, and its performance parameters, including maximum uplink and downlink gain, serial number of repeater, software version in Control Module, controller hardware version, as well as hardware version of all included components.  The repeater can be equipped with a wireless modem (GSM, GSM-R, EDGE, etc) or a PSTN modem mounted inside the repeater. The repeater is also equipped with Ethernet.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  36 (105)  The Control Module contains a battery backed-up real time clock, which will stay active even during a power failure. The real time clock is used for instance to keep track of when an alarm occurred, when to retransmit an alarm and at what time of the day to send traffic report to the AEM. If the repeater is controlled by the Axell Element Manager, the AEM will automatically time synchronize repeaters, to ensure that the time is always set correctly in the entire repeater network. Slave repeaters are synchronized from the OMU.  4.2 Network Nodes  Note! The description in this section is based on a master-slave set-up of the system, where the OMU is the node master and the repeaters are the slaves. An Axell Wireless OMU-Repeater system consists of an OMU unit and a number of remote nodes (repeaters) connected to the OMU unit via fibre optic cables. During software setup of the system, all nodes installed in the system are configured in the Control Module. Hence, the node master contains a list of all the repeaters in the system. Once a node is added to the system, it is also written to all the nodes installed. This means that all nodes in the repeater system have information about all other nodes, allowing for a very good overview of the entire repeater system no matter what node the repeater system login is made from.  4.2.1 Node Identification All nodes have a unique address within the repeater system. This address is based on the serial number of the node. When the system is installed to the Axell Element Manager, the master unit is assigned a unique repeater ID within the AEM database.  This number is on the form: XX-YY-ZZZZ where XX   is the AEM installation number within the network YY   is the region number within the AEM-system ZZZZ  is the site installation number Within the repeater system, all slave nodes (repeaters) are given a unique ID, based on the AEM assigned ID. The nodes share the XX-YY- part of the master ID, but the ZZZZ is replaced by the node’s serial number. Example: If the master’s ID is 17-42-4711 and the serial number for a node in the system is 23BJ. The node’s ID will be 17-42-23BJ. 4.2.2 Node Addressing Modes When logging in to the OMU-repeater system, it is possible to view information about any of the nodes in the system, as long as they are added to the node list. All nodes can be addressed in four different ways, all starting with the @-sign. Numeric Addressing Each node in the network gets a unique ID-number in the Node List as they are added to the system. Node 0 is always the master node. Addressing is on the format: @K K   from 0 to N where N is number of nodes Reading a parameter from node 3 is entered as: AVITEC AB> @3 GET ATD 14 AVITEC AB>
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  37 (105)  Serial Number Addressing A node can be accessed using the serial number of the node. Example: AVITEC AB> @2J34 GET MDL MBF-I AVITEC AB> Node ID Addressing A node can also be addressed using the full Node ID. Example: AVITEC AB> @01-01-2J34 GET TAG SITE3_TUNNEL_OPENING AVITEC AB> Direct Node Addressing When many attributes are intended for another node, the user can enter Direct Node Accessing mode, where the node the user is logged in redirects all commands to the destination node.  This mode is configured by sending the command: SET DNA [Node Address] where any of the node addressing modes can be used as Node Address.  When going into direct node addressing, the command prompt is changed to reflect what node is currently addressed: AVITEC AB> SET DNA 2J34 AVITEC AB @2J34>  Refer to attribute DNA in OMU Command and Attribute Summary for further details on direct node addressing. 4.2.3 System Wide Parameters System Wide Parameters are parameters that when configured should be written to all nodes in the system. When setting a system wide parameter, the parameter is always set in the node master, which is then responsible for setting the parameter to all other nodes. If attempting to set a system wide parameter from a node as access to the node master is not available, setting the parameter will fail. The following “standard” parameters are treated as system wide parameters (please refer to OMU Command and Attribute Summary for details): LMT   Local Maintenance Terminal timeout TIM   Setting the time DAT   Setting the date TPD   Setting the time for sending traffic / utilization report to the AEM UID   User ID’s PWD  Passwords RID   Repeater ID In slave repeaters the OMU is responsible for the communication with the AEM.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  38 (105)  4.2.4 Node Access An operator can login to the system from any node in the network and access all parameters in all nodes, including those in the node master unit. This can be done using a serial cable connected to the node’s LMT-port or by remote access over a modem in the master unit.   Select “System Nodes”     Node detailes: number, ID, Model  Node name  Node status     Select a node by clicking on  . The RMC will now connect to the selected node. The OMU unit polls the connected repeaters / nodes regularly and keeps control of login requests. If a user at a repeater site wants to log in to the system, the OMU Control Module is responsible for granting / denying the login request. If a user forgets to log out from the node when a session is finished, the system will automatically log the user out after a configurable number of minutes of inactivity.   4.3 Fibre Loss Compensation Each fibre optic link in the system will induce a loss. This loss will also differ in magnitude from one link to another since the distances between each repeater and the OMU is different. The Axell Wireless OMU-repeater system can automatically calculate this loss, compensate for the loss in each link and by that also balance the system. This is accomplished by using a pilot tone of a well defined level which is sent from the master node to the slave and vice versa. The received level of the pilot tone is measured and the loss is calculated. The Fibre Optic Converter is automatically adjusted to compensate for the loss. The adjustment is made towards a target value which means that the system will also be balanced (all fibers will appear to have the same loss). The maximum compensation is 10dB which equals an unbroken fibre distance of 20 km. For each connection in the link (for instance at the ODF) approximately 0.5 dB will have to be added to the loss. The loss compensation function is activated by some quick commands as the system is set up. Each time the system has been changed or fibres have been exchanged or moved for some reason, it is recommended to re-activate this function.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  39 (105)  4.4 Alarm System The Axell Wireless repeaters contain a number of different alarm sources, both analogue and digital, to ensure that the repeater works with desired performance. 4.4.1 Alarm Sources Temperature Related Alarms Alarm  Code Description  Trigger Temperature  TEM  Measures the temperature in the Control Module  Temperature too high or too low  Radio Board Temperature RBT  Measures the temperature on the defined radio or opto module Temperature too high or too low Power Supply Temperature PTM  Measures the temperature in the power supply   Temperature too high or too low Power Related Alarms Alarm  Code Description  Trigger Power Supply Level PSL  Monitors the input voltage level to the repeater  Level too high or too low Power Supply 1   PW1  Measures the +28V generated by the repeater’s power supply. Level too high or too low Power Supply 2   PW2  Measures the +15V generated by the repeater’s power supply. Level too high or too low Power Supply 3   PW3  Measures the +6.45 V generated by the repeater’s power supply Level too high or too low Power Supply 4   PW4  Measures the backed up +6.45 V generated by the repeater’s power supply Level too high or too low Battery Level  BAT  Measures the power level in the battery  Level too high or too low Repeater Performance Related Alarms Alarm  Code  Description  Trigger Amplifier/Gain Downlink AD1-4  The repeater measures the input signal level in the downlink and compares it to expected output power with regards to set attenuation. If the output power is too high or too low an alarm is triggered. Expected output power too high or too low compared to calculated output power Amplifier/Gain Uplink AU1-4  The repeater measures the input signal level in the uplink and compares it to expected output power with regards to the set attenuation. If the output power is too high or too low an alarm is triggered. Expected output power too high or too low compared to calculated output power Amplifier  ASD  Measures saturation in the downlink, measured  Saturation enters
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  40 (105)  Alarm  Code  Description  Trigger Saturation Downlink on the radio module.  An amplifier chain going into saturation means that the input signal level is too high. defined level  Power Amplifier Downlink Error PAE  Monitors the alarms from the MCPA  Non-fatal alarms from the MCPA Power Amplifier Downlink Fatal Error PAF  Monitors the alarms from the MCPA  Fatal alarms from the MCPA Power Downlink Level  PD1-4  Measures the output power in the downlink. If it drops below the configured threshold an alarm is generated. Output power level (too high) or too low Communication Related Alarms Alarm  Code Description  Trigger Communication with Active Devices COM  Detects errors in the communication between  the Control Module and other active devices, such as power supplies, radio module, MCPA, ref generator and Fibre Optic Converter Errors in the communication EEPROM CRC check in active devices CRC  Controls checksum in radio module, MCPA and Fibre Optic Converter Checksum wrong Received Data Packet Quality RXQ  Measures the quality of the received data from the node master Quality too low Communication between the Radio Module and the MCPA CMM  Monitors the communication between the Radio Module and the related MCPA. Errors in the communication Opto Related Alarms Alarm  Code Description  Trigger Received Optical Level RXO  Measures the received optical signal level  Optical signal level too low Transmitted Optical Level TXO  Measures the transmitted optical signal level  No transmission Received Pilot Tone Level RXP  Measures the pilot tone level  Level too high or too low Synthesizer Pilot Tone Generator SZP  Measures the pilot tone frequency  Error on pilot tone Door Alarm Alarm  Code Description  Trigger Door  DOO  Checks if the repeater’s door is open or closed  Door is open
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  41 (105)  External Alarms Alarm  Code Description  Trigger External Alarm 1  EX1  Monitors any alarm source, for example fire alarms or external door sensors connected to the external interface. Error from alarm source External Alarm 2  EX2  Monitors any alarm source, for example fire alarms or external door sensors connected to the external interface. Error from alarm source External Alarm 3  EX3  Monitors any alarm source, for example fire alarms or external door sensors connected to the external interface. Error from alarm source External Alarm 4  EX4  Monitors any alarm source, for example fire alarms or external door sensors connected to the external interface. Error from alarm source Relay Output for Sum Alarm The module for external alarms contains a relay output. The relay can be used to indicate the summary status of the repeater. Each alarm source can be configured to be affecting the relay or not.  4.4.2 Alarms and End of Alarms When the Control Module detects a failure in the repeater, an alarm is transmitted to the Axell Element Manager, informing the operator about the error condition. When the alarm has ceased, an end of alarm is sent to the AEM, stating that the alarm source is now OK.  For slave type repeaters in a OMU-repeater system this communication is initiated and managed by the OMU. Each “alarm” and “end of alarm” updates the AEM database with the latest status of the alarm source, ensuring that the AEM operator always has the correct repeater status in the system.  To generate an alarm a number of consecutive measurements must first show an error state. This can be configured for each alarm source separately.   To generate an end of alarm only one OK measurement is needed.   Alarm levelTimeAlarm thresholdAlarm is sent after three seconds above thresholdEnd of alarm is sent as soon as status is OK If an alarm should constantly toggle between OK and ERROR the communications interface might be blocked. To prevent this there is a parameter called Minimum Alarm Repetition Cycle. This parameter defines how many minutes must elapse before a new alarm can be transmitted from the same alarm source.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  42 (105)  Alarm ThresholdInitial alarm End of AlarmThree minutes have elapsed and a new alarm is transmittedMinimum alarm repetitionAlarm levelTime This illustration shows an alarm source with an upper threshold, and a fluctuating level around the alarm threshold. In this example, the first alarm will be sent as indicated. The next alarm will be transmitted after three minutes, when the minimum alarm repetition period has elapsed.  In this configuration a new alarm will not be sent before three minutes have elapsed. This variable can be set from 0 to 99. If it is set to 0 the feature is disabled.  Set Minimum Alarm Repetition Cycle Select “Configuration “ and “Reports”             4.4.3 Alarm Retransmissions and Acknowledgements  As soon as the repeater detects an alarm or an end of alarm, a connection to the Axell Element Manager is established and the alarm event is reported.  The 2 000 latest alarms and end of alarms are stored in the repeater’s local alarm log. In case an alarm is not acknowledged the alarm will be retransmitted to the AEM after a configurable number of minutes. Allowed values are 0 to 999. Default retransmit interval is 10 minutes. The retransmission will be repeated a configurable number of times. This variable can be set from 0 to 99. Default number of retries is three  Set Number of Retransmissions and Repetition Cycle for Non-acknowledged Alarms Select “Configuration “ and “Reports”
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  43 (105)  4.4.3.1 Alarm Acknowledgement using the RMC Each alarm can be manually acknowledged using the Repeater Maintenance Console. However, if the repeater is controlled by the Axell Element Manager, a manual acknowledgement of the alarm means that the AEM will not be aware of the change in the repeater status.  4.4.3.2 Alarm Acknowledgement using the Axell Element Manager If the repeater is integrated to and controlled by the Axell Element Manager (via an OMU or directly), an alarm is considered acknowledged when the alarm has been delivered to the AEM. Once delivered to the AEM, the acknowledgement of the event is taken care of locally at the AEM, why no dial-back needs to be performed to acknowledge the alarms in the repeater. 4.4.3.3 Alarm Acknowledgement using SMS Note! SMS functionality is not implemented in this SW release. If the repeater is configured to send alarms using SMS, alarm acknowledgement can be made in two different ways.  the alarm is acknowledged as soon as the alarm SMS is successfully received by the Short Message Service Centre or  the alarm is acknowledged by sending a special alarm acknowledgement SMS back to the repeater from the alarm destination.  Set Acknowledgement Type for SMS Alarms Select “Configuration “ and “Reports”             Pick one alternative from the drop-down menu   All alarms transmitted from the repeater contain a message number. Acknowledgement of an alarm is done by sending an SMS to the repeater containing this message number.  Note! Only the defined “Primary SMS address” can acknowledge alarms. The table below displays the format of alarm acknowledgement messages. Message field  Format  Description Repeater ID  XX-YY-ZZZZ  ID of the repeater that the message is intended for Message number  NNNNN  Message number set by originator Command  ACT  Action command  Argument  ACK  Acknowledge action Argument  MMMMM  Message number of the alarm message to acknowledge
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  44 (105)  The message fields are separated with blanks.  For example, sending an SMS to the repeater with the text 01-42-4711 00242 ACT ACK 00023 will acknowledge alarm number 00023 from repeater 01-42-4711. 4.4.4 Alarm Format Each alarm transmitted from the repeater contains a number of fields, in detail describing the event that caused the alarm. The alarm is transmitted as an ASCII text string, each field separated by a blank/white space. Using the Axell Element Manager to control the repeater, the alarm string is delivered to the transceiver for further processing in the AEM system. When SMS is used to control the repeater, the string is sent as clear text to the alarm address (main address).  Note! The SMS functionality is not implemented in repeaters with this SW release. Message field Format  # of char. Description Repeater ID  XX-YY-ZZZZ  10  ID of the repeater causing the alarm. When monitoring the repeater using the AEM, this repeater ID is set by the AEM during the repeater installation phase. Using SMS, this repeater ID should be modified to uniquely identify the repeater in the network. Message #  N  1 to 10  This integer value uniquely identifies this message from the repeater and may be from 0 to 2147483648 (231). Message type  ALARM  5  This text string identifies the message as being an alarm (or end of alarm) Date  DDMMYY  6  Day, month and year when the alarm was detected Time  HHMMSS  6  Hour, minute and second when the alarm was detected Alarm Name  CCC  3  Identifies the alarm type (e.g. PW1, SZU, PDL, etc) Alarm Severity  CC  2  Abbreviation for severity of the alarm. This severity varies between the different alarm sources. CR = critical   MA = major MI = minor WA = warning CL = cleared When an and of alarm is sent, the severity is CL = cleared Alarm Class  CC  2  Abbreviation for kind of alarm CO = communication alarm EN = environmental alarm QS = quality of service alarm PR = processing alarm EQ = equipment alarm Status  C  1  This status identifier is 0 if end of alarm and 1 if alarm. Hardware Enumeration CCCC  1 to 5  Denotes what hardware module the alarm originates from. If not used, a '-' (dash) is replied. Position Identifier CCCCCCCCCCCC 1 to 12  Gives detailed information about certain alarm sources. For some alarms, such as VLI, LGO and CLR, this may contain user information. If not used, a '-' (dash) is replied. Additional text  <Text>  60  This quoted string contains additional alarm information, such as measured levels when the alarm condition was detected.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  45 (105)  4.4.5 Alarm Class Each alarm belongs to a class. The defined classes are: Class  Description CO  Communications  QS  Quality of service PR  Software or processing EQ  Hardware equipment EN  Environment (enclosing or surrounding equipment)  All alarms are configured to a class at delivery but can be changed by the user. The external alarms do not have a classification at delivery, but can be set by the user. 4.4.6 Alarm Severity Alarms can be of five different severity levels. Severity Level  Description  Critical  A critical error has occurred which affects the functionality of the repeater. This type of alarm requires immediate action.  Major  A major error has occurred. This type of alarm should be investigated within a short time.  Minor  A minor error has occurred. This type of alarm should be investigated, but is not urgent.  Warning  Something has occurred that does not affect the operation of the repeater but may be important to notice. For example, someone has logged on to the repeater.  Cleared  A cleared alarm. This is the end of alarm. The severity can be defined for each alarm source in the Alarm Configuration screen in the RMC. It is recommended not to change the default settings.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  46 (105)  4.4.7 Alarm Configuration A number of different parameters can be configured for how the alarms are transmitted to the repeater OMC. Each alarm source can also be individually configured in a number of different ways.  Note! The alarm configuration window will differ from the one below but have similar functionality. Select “Configuration “ and “Alarms”         Affect Relay  Alarm transmission enabled  Requires acknowledgement  Lower and upper threshold  Number of faulty measures before an alarm is triggered      Affect relay  If checked, an active alarm from the alarm source affects the relay status Enabl.   If checked, the alarm is transmitted to the repeater OMC  Note! This only affects the transmission of the alarm. The alarm is still measured, and corresponding alarm status is still displayed in the repeater status screen and in the heartbeat reports transmitted to the repeater OMC.  Ack.  All alarms will by default be transmitted to the repeater OMC requiring acknowledgement (the box is checked). Disabling this checkbox removes this requirement, which means that an alarm will only be transmitted once, regardless if an acknowledgement is received or not. Lower  Lower threshold, not applicable for all alarm sources. Please refer to documents Command and Attribute Summary for details on the usage of thresholds for each alarm source. Upper  Upper threshold, not applicable for all alarm sources. Please refer to documents Command and Attribute Summary for details on the usage of thresholds for each alarm source. Time  Defines how many consecutive measurements from one alarm source that should be measured as ERROR before an alarm is triggered.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  47 (105)  External Alarms Four external alarm sources can be connected to the External Alarm module in the repeater. These can be for instance fire alarms or external door sensors.  The alarm sources must generate a voltage between 12 and 24 VDC. The presence or absence of voltage will trigger the alarm depending on how alarm thresholds have been configured in the controller software. Each alarm can also be given a unique name.  The external alarms can be set as “active high” or “active low” As for all alarm sources a delay can be set that defines how many seconds an alarm should be in error state before an alarm is generated. To define names and polarity of the external alarms use the lower part of the Alarm Configuration screen.   Set the dip-switches to configure the external alarms  Name the alarms   The external alarms can be given individual names of up to 19 characters. Click on Edit and insert the new names.     For more information about external alarms see 5.2.7  Connect External Alarms. Sum Alarm  The module for external alarms contains a relay output. The relay can be used to indicate the summary status of the repeater. Each alarm source can be configured to be affecting the relay or not.  Note! The relay status is not affected by the login / logout alarm parameters. For installation testing purposes, it is possible to test the open / close function of the relay. This test procedure makes sure the relay is closed for 3 seconds, then opens for 10 seconds, and finally closes for 3 seconds before going back to original state.  The relay can be set to close or open to indicate an alarm. This can be changed by changing the polarity.   Click on Relay Test  Relay polarity
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  48 (105)  4.4.8 Alarm Monitoring The alarms can be monitored via the RMC. Each alarm has an indicator that is either green or red. See also reference to section 4.4.1 Alarm Sources. Uplink Related Alarms  Amplifier, AU1-4. The repeater measures the input signal level in the uplink and compares it to expected output power with regards to set attenuation. If the output power is too high or too low an alarm is triggered.     Downlink Related Alarms   Amplifier, AD1-4. The repeater measures the input signal level in the downlink and compares it to expected output power with regards to set attenuation. If the output power is too high or too low an alarm is triggered.   Saturation Status, ASD. Measures saturation in the downlink.   Power Level, PD1-4. Measures the output power in the downlink.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  49 (105)  General Alarms  Door, DOO. Door to repeater open  Controller Temp, TEM. Temperature in Control Module too high or too low  External Alarms, EX1-4. Alarm from external source Power Supply Related Alarms  Com, COM. Error in communication with Power Supply  Temperature, PTM. Temperature in Power Supply too high or too low  Power Supply Input, PSL. Input power to the repeater too high or too low  Battery, BAT. Power level in battery too high or too low  Power P1-4, PW1-4. +28VDC, +15VDC, +6,45VD and backed up +6,45 VDC too high or too low Reference Generator Related Alarms  Com, COM  Error in communication with module  Power P3, PW3. Relevant power to module too high or too low Radio Board Related Alarms  Com, COM  Error in communication with module  Power P2-3, PW2-3  Relevant power to module too high or too low  Radio board temp, RBT. Temperature in Radio Board too high or too low  MCPA temp, RBT Temperature in MCPA too high or too low  Radio board CRC, CRC Faulty checksum in Radio Board  MCPA Condition, PAE Error in MCPA  Fatal MCPA Condition, PAF Fatal error in MCPA  MCPA Com, CMM Error in communication between the radio board and the MCPA   Fibre Optic Converter Related Alarms  Com, COM. Error in communication with module  Temperature, RBT. Temperature in Fibre Optic Converter too high or too low  Transmitter, TXO. No detectable transmitted optical signal  Received Level, RXO. Received optical level too low  Pilot Tone Gen Synth, SZP. Pilot tone frequency faulty  Re. Pilot Tone Level, RXP. Pilot tone level too high or too low  EEPROM CRC, CRC. Faulty checksum in Fibre Optic Converter
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  50 (105)   Power Supply Alarms Additional power levels and alarms is monitored by clicking    Power Supply Input, PSL  P1 – Pwr Sup +28V, PW1  P2 – Pwr Sup +15V, PW2  P3 – Pwr Sup +6,45V, PW3  P4 – Pwr Sup +6,45V, PW4  Battery, BAT                System Node Alarms  COM, Node Communication, NCO.  Error in communication with slave (repeater)  Status. Sum status of slave repeater
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  51 (105)  4.4.9 Alarm Log Recent alarms can be viewed in an alarm log that shows details about the alarms. Note! The alarm log window will differ from the one below but have similar functionality.  Select “Log” and “Alarm Log”          Message No  Date/Time Description  Attribute/Alarm Source Severity  Class Alarm acknowledged  Acknowledgement using RMC
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  52 (105)  4.5 Repeater Heartbeat  On regular intervals, the repeater sends a heartbeat report to the AEM to confirm that the repeater is functioning. The heartbeat message contains information about the RF-configuration and the alarm sources. It ensures that the data communication from the repeater to the AEM is working properly. The heartbeat interval can be set from 1 to 1440 minutes. Setting the heartbeat to 0 disables the transmission of heartbeats.  Slave repeaters in OMU-repeater system send the heartbeat messages to the OMU. The heartbeats are sent on to the AEM by the OMU. 4.5.1 Heartbeat Tasks With the heartbeat reports, a number of tasks are carried out. 4.5.1.1 Ensuring Repeater to AEM Communications path By configuring the repeater to regularly establish a connection to the AEM, the functionality of the data communications path between the repeater and the AEM is verified. This ensures that for instance the alarms will be transmitted properly. If an expected heartbeat is not received by the AEM, an alarm is generated to the AEM operator. Reasons for a heartbeat message failing to be delivered can be:  No power – the repeater site might experience a power failure, and the battery backing up the Control Module and modem is empty  Broken donor antenna – If the repeater antennas have been tampered with, the repeater might not get adequate signal to establish a connection to the AEM  Failing BTS – If the feeding BTS for some reason goes down, the repeater will loose its network connection, and hence fail to establish a connection to the Axell Element Manager. 4.5.1.2 AEM Database Synchronization The Axell Element Manager stores all repeater parameters in a database. This database is populated during the repeater integration into the AEM, when the AEM downloads all the repeater parameters. If the AEM operator wants to monitor the configuration of the repeater, the parameters can be read from the database without having to connect to the repeater. In case of an alarm, the AEM updates the database with the status of the alarm source. In case the repeater failed to deliver the alarm to the AEM, there will be a discrepancy between the repeater configuration and the configuration in the database. Furthermore, if a technician at site makes changes to the RF-configuration of the repeater, the configuration will differ from the AEM configuration. For this reason, each heartbeat report contains all the relevant RF-parameters and status of all the alarm sources in the repeater. This means that each heartbeat report will update the AEM with all status and RF parameters. Note! Once the repeater is integrated to the Axell Element Manager, it is recommended that all reconfigurations are made from the AEM.  Note! If a user logs in to the repeater making changes, as soon as the user logs out, an alarm will be transmitted to the AEM informing the operator that a change has been made. When this alarm is received, the operator can initiate repeater synchronization where all repeater parameters will be updated. 4.5.1.3 Time Synchronization Each heartbeat message transmitted to the AEM contains a time stamp of the local time inside the repeater. Upon reception in the AEM, the time stamp is compared to the Axell Element Manager time. If the difference between the repeater and AEM time is too big, time synchronization is initiated by the AEM, adjusting the time in the repeater. In this ways, we ensure that a repeater integrated to the Axell Element Manager always contains the correct time information.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  53 (105)  Note! If the time is adjusted by a user logged in to the repeater, once the user logs out, a heartbeat is sent to the AEM to ensure that the time is correctly synchronized.  4.5.2 Heartbeat Format The heartbeat report is transmitted as an ASCII text string, with a number of fields representing the RF-configuration and status parameters, each field separated by a blank/white space. Using the Axell Element Manager to control the repeater, the heartbeat report is delivered to the Transceiver for further processing in the AEM system. Field   Format  # of char Description Repeater ID  XX-YY-ZZZZ  10   Message no  NNNNNNNNN  9   State  STATE  5   Date  DDMMYY  6   Time  HHMMSS  6   IHU  NNNNNNNNNNNN 12  Installed hardware units. 0 = not installed 1 = installed Hardware order: PSUP1, PSUP2, RefGen, RadioUnit1, RadioUnit2, RadioUnit3, RadioUnit4, FiberOptic1, FiberOptic2, FiberOptic3, FiberOptic4, Comm.Multiplexer ATD  XXYYZZWW  8  Attenuation in downlink ATU   XXYYZZWW  8  Attenuation in uplink LVD/LVU   JKLMXYZW  4  Output Power Enabled / Disabled in downlink/uplink AMD/AMU   NN  2       Status of amplifier chain downlink/uplink.  These values are Hex Coded, and should be used in conjunction with COM status for actual device. For example, the Byte 1 status is sent as Hex ‘8’, which is extracted to 1000. Byte 1 Bit 3  Bit 2  Bit 1  Bit 0 Amplifier Chain 1 Downlink Amplifier Chain 2 Downlink Amplifier Chain 3 Downlink Amplifier Chain 4 Downlink Byte 2 Bit 3  Bit 2  Bit 1  Bit 0 Amplifier Chain 1 Uplink Amplifier Chain 2 Uplink Amplifier Chain 3 Uplink Amplifier Chain 4 Uplink  ASD  N  1  Status of amplifier saturation downlink These values are Hex Coded, and should be used in conjunction with COM status for actual device. For example, the Byte 1 status is sent as Hex ‘8’, which is extracted to 1000. Bit 3  Bit 2  Bit 1  Bit 0 Amplifier Chain 1 Downlink Amplifier Chain 2 Downlink Amplifier Chain 3 Downlink Amplifier Chain 4 Downlink  BAT  N  1  Status of Battery Charge CMM  N  1  Status of communication between Radio Board and MCPA.  These values are Hex Coded, and should be used in conjunction with COM status for
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  54 (105)  Field   Format  # of char Description       actual device. For example, the Byte 1 status is sent as Hex ‘8’, which is extracted to 1000. Bit 3  Bit 2  Bit 1  Bit 0 MCPA Comm. Chain 1 MCPA Comm. Chain 2 MCPA Comm. Chain 3 MCPA Comm. Chain 4  COM  NNNNNNNNNNNN 12  Status of communication between controller and active devices CRC  NNN  3        Status of CRC Status for target firmware. These values are Hex Coded, and should be used in conjunction with COM status for actual device. For example, the Byte 1 status is sent as Hex ‘8’, which is extracted to 1000. Byte 1 Bit 3  Bit 2  Bit 1  Bit 0 CRC Radio Unit 1 CRC Radio Unit 2 CRC Radio Unit 3 CRC Radio Unit 4 Byte 2 Bit 3  Bit 2  Bit 1  Bit 0 CRC Fibre Optic Unit 1 CRC Fibre Optic Unit 2 CRC Fibre Optic Unit 3 CRC Fibre Optic Unit 4 Byte 3 Bit 3  Bit 2  Bit 1  Bit 0 Com Mux  0  0  0   MSC  NN  2               Status of MCPA, both errors and fatal errors.  These values are Hex Coded, and should be used in conjunction with CMM status for actual MCPA. For example, the Byte 1 status is sent as Hex ‘A’, which is extracted to 1010. Byte 1 Bit 3  Bit 2  Bit 1  Bit 0 Fatal Error MCPA 1 Error MCPA 1  Fatal error MCPA 2 Error MCPA 2 Byte 2 Bit 3  Bit 2  Bit 1  Bit 0 Fatal Error MCPA 3 Error MCPA 3  Fatal error MCPA 4 Error MCPA 4  PDL  N  1        Status of Power Downlink Level.  These values are Hex Coded, and should be used in conjunction with COM status for actual device. For example, the Byte 1 status is sent as Hex ‘8’, which is extracted to 1000. Bit 3  Bit 2  Bit 1  Bit 0 Power Level Chain 1 Downlink Power Level Chain 2 Downlink Power Level Chain 3 Downlink Power Level Chain 4 Downlink
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  55 (105)  Field   Format  # of char Description  PSL  N  1  Status of Power Supply Input Level PTM  NN  2  Status of Power Supply Temperature PW1  NN  2              Status of 28V Power Supply distribution.  These values are Hex Coded, and should be used in conjunction with COM status for actual device. For example, the Byte 1 status is sent as Hex ‘8’, which is extracted to 1000. Byte 1 Bit 3  Bit 2  Bit 1  Bit 0 PW1 Power Supply 1 PW1 Power Supply 2 PW1 Radio Unit 1 PW1 Radio Unit 2 Byte 2 Bit 3  Bit 2  Bit 1  Bit 0 PW1 Radio Unit 3 PW1 Radio Unit 4 0  0  PW2  NN  2              Status of 15V Power Supply distribution.  These values are Hex Coded, and should be used in conjunction with COM status for actual device. For example, the Byte 1 status is sent as Hex ‘8’, which is extracted to 1000. Byte 1 Bit 3  Bit 2  Bit 1  Bit 0 PW2 Power Supply 1 PW2 Power Supply 2 PW2 Radio Unit 1 PW2 Radio Unit 2 Byte 2 Bit 3  Bit 2  Bit 1  Bit 0 PW2 Radio Unit 3 PW2 Radio Unit 4 0  0  PW3  NN  2             Status of 6.45V Power Supply distribution. These values are Hex Coded, and should be used in conjunction with COM status for actual device. For example, the Byte 1 status is sent as Hex ‘8’, which is extracted to 1000. Byte 1 Bit 3  Bit 2  Bit 1  Bit 0 PW3 Power Supply 1 PW3 Power Supply 2 PW3 Radio Unit 1 PW3 Radio Unit 2 Byte 2 Bit 3  Bit 2  Bit 1  Bit 0 PW3 Radio Unit 3 PW3 Radio Unit 4 PW3 Ref Gen  PW3 Com Mux  PW4  N  1  Status of 6.45V Backup Power Supply distribution RBT  NNN  3  Status of Radio Board Temperatures. These values are Hex Coded, and should be used in conjunction with COM status for
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  56 (105)  Field   Format  # of char Description                  actual device. For example, the Byte 1 status is sent as Hex ‘8’, which is extracted to 1000. Byte 1 Bit 3  Bit 2  Bit 1  Bit 0 Temp Radio Unit 1 Temp Radio Unit 2 Temp Radio Unit 3 Temp Radio Unit 4 Byte 2 Bit 3  Bit 2  Bit 1  Bit 0 Temp MCPA 1  Temp MCPA 2  Temp MCPA 3  Temp MCPA 4 Byte 3 Bit 3  Bit 2  Bit 1  Bit 0 Temp Fibre Optic Unit 1 Temp Fibre Optic Unit 2 Temp Fibre Optic Unit 3 Temp Fibre Optic Unit 4  RXO  N  1        Status of Received Optical Level These values are Hex Coded, and should be used in conjunction with COM status for actual device. For example, the Byte 1 status is sent as Hex ‘8’, which is extracted to 1000. Bit 3  Bit 2  Bit 1  Bit 0 RXO Fibre Optic Unit 1 RXO Fibre Optic Unit 2 RXO Fibre Optic Unit 3 RXO Fibre Optic Unit 4   RXP  N  1        Status of Received Pilot Tone level  These values are Hex Coded, and should be used in conjunction with COM status for actual device. For example, the Byte 1 status is sent as Hex ‘8’, which is extracted to 1000. Bit 3  Bit 2  Bit 1  Bit 0 RXP Fibre Optic Unit 1 RXP Fibre Optic Unit 2 RXP Fibre Optic Unit 3 RXP Fibre Optic Unit 4  RXQ  N  1  Status of Received Data Quality If repeater is NOT a system slave, this reports as a dash. SZP  N  1         Status of Synthesizer in Pilot Tone Generator  These values are Hex Coded, and should be used in conjunction with COM status for actual device. For example, the Byte 1 status is sent as Hex ‘8’, which is extracted to 1000.  Bit 3  Bit 2  Bit 1  Bit 0 SZP Fibre Optic Unit 1 SZP Fibre Optic Unit 2 SZP Fibre Optic Unit 3 SZP Fibre Optic Unit 4  TEM  N  1  Status of temperature in Controller TXO  N  1  Status of Optical Transmitter  These values are Hex Coded, and should be used in conjunction with COM status for
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  57 (105)  Field   Format  # of char Description       actual device. For example, the Byte 1 status is sent as Hex ‘8’, which is extracted to 1000. Bit 3  Bit 2  Bit 1  Bit 0 TXO Fibre Optic Unit 1 TXO Fibre Optic Unit 2 TXO Fibre Optic Unit 3 TXO Fibre Optic Unit 4  EX1/EX2/EX3/EX4  NNNN  4  Status of external alarm inputs DOO  N  1  Door status NMP  X  1  Communications path to node master in the Communications Multiplexer. If not used, a dash is reported. RCH  NNNNNN  6  Repetition Cycle for Heartbeat reports  4.5.3 Heartbeat Log Recent heartbeats can be viewed in a log that shows details about the alarms. Monitor Alarm Log via the RMC Select “Alarm Log” and “Heartbeat Log”         Message No  Date/Time Description  Retransmissions Message     The heartbeat message format is described in section 4.5.2 Heartbeat Format. 4.6 RF Parameters The attenuation can be changed in 1 dB steps. If the attenuation for example is set to 15 dB, the repeater is downgraded 15 dB from its maximum performance.  Maximum gain in the repeater can be read from the Product Information menu (choose Configuration/Product).
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  58 (105)  Setting the gain in the repeater plays an important role in the repeater configuration.  The gain is adjusted by changing the attenuation of the repeater. The setting is done for the uplink and downlink separately. The attenuation can be changed in 1 dB steps. If the attenuation for example is set to 15 dB, the repeater is downgraded 15 dB from its maximum performance.  Maximum gain in the repeater can be read from the Product Information menu (choose Configuration/Product).         4.6.1 Power Level The repeater has a constant gain in both uplink and downlink paths. The gain is set by defining the attenuation as described above.  The repeater has a defined maximum output level. If the input signal amplified by the gain set exceeds the set output limit, an ALC (Automatic Level Control) loop is activated. This ALC ensures that the amplifier does not add distortion to the radio signal. Below are examples of the ALC function for one and two carriers. ALC one carrierInput signal, dBmOutput power, dBm+36,5+33,8-24 -16Gain: 60 dB+35ALC two carriers
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  59 (105)  4.6.2 Input / Output Levels  By using the input/output values together with the gain settings in the repeater it is possible to monitor the functionality of the amplifier chains. These measurements can also be useful during installation of the repeater.  Monitoring the output level is helpful in determining how much the gain must be increased to reach maximum output power. The input and output power levels to and from the repeater are constantly monitored.  If the power levels are lower than the lowest detectable level, the RMC reports a dash.  Note! Uplink power levels can only be displayed when there is a user in the repeater coverage area generating traffic.  In this example there is no signal on the uplink nor on the downlink.         4.6.3 ALC   The repeater is equipped with an ALC, Automatic Level Control. The ALC is an immediate reaction to the input signal level which keeps the output level to the maximum defined level.     +20Input Signal, dBmOutput Power Level, dBmGain 70dB-50ALC 4.7 Hardware Identification A repeater contains a number of different modules. Some of these are active devices meaning that they contain a micro controller used for monitoring module parameters. Some are passive devices, for example the external alarm interface. The Control Module communicates with the active devices using a master/slave configuration, where the Control Module is the master and the active devices are slaves. Each active device uses its serial number as an address. A slave only replies to requests with the correct address information.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  60 (105)  During manufacturing the repeater is configured with all the serial numbers of all the devices in the system. For passive devices, the article number of the device is added. Once the system is configured, the Control Module polls all the active devices for article numbers and production information as well as software versions and statistics of the active devices.  Via the RMC the full repeater inventory can be read, including statistics of the active devices. When a login to a repeater is made using the Repeater Maintenance Console, the RMC detects the repeater type and adjusts the user interface correspondingly. The same RMC can be used for all repeater types. Via the RMC basic information about the repeater configuration can be monitored.  Select “Configuration” and  “Product”           General repeater information  Hardware devices installed  Active devices installed  More details regarding selected item  Control Module information   Additional information regarding Radio Board and MCPA                  4.8 Tag and ID  When the repeater is integrated into the Axell Element Manager the repeater is assigned a repeater ID, which is a unique identifier in the repeater network. This ID is used by the AEM to keep track of the repeaters in the AEM database.  The repeater Tag can be used to give the repeater a more logical name, such as the site or installation place. If Tag is set during site installation, this can easily be read by the AEM during AEM integration, giving the AEM operator a clear identification of the site. The repeater tag can be locked so that the tag can not be accidentally changed from the AEM. Refer to section 5.6.2 Set Repeater Name (TAG) for information about how to set the repeater Tag.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  61 (105)  4.9 User Access  Several users at a time can be logged on to a Repeater, for instance one locally via the RS232 interface and one remotely via modem. There is one default user name and password defined for the repeater.  User Name  Password avitec  AvitecPasswd Note! Both the user name and the password are case sensitive. The password can be changed and new accounts be added once a logon has been made. This is made in terminal mode. Please refer to the Command and Attribute Summary. A user will be logged out after a configurable number of minutes of inactivity. This time can be defined via the RMC. 4.9.1 Configure Automatic Logout Select “Configuration” and “Communication”             Note! A password for the repeater’s communication with the AEM can be set in the box above but it is recommended that it is done from the AEM, and NOT from here. 4.9.2 Change Username or Password Select “Configuration” and “Communication”      Make the changes
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  62 (105)  4.9.3 User Access in a Network Application An operator can login to the system from any node in the network and access all parameters in all nodes, including those in the node master unit. This can be done using a serial cable connected to the node’s LMT-port or by remote access over the modem (GSM or PSTN) in the master unit, or in the repeater itself.  In an OMU-repeater system with slave-type repeaters the OMU unit polls the connected repeaters / nodes regularly and keeps control of login requests. If a user at a repeater site wants to log in to the repeater system, the OMU Control Module is responsible for granting / denying the login request. If a user forgets to log out from the node when a session is finished, the system will automatically log the user out after a configurable number of minutes of inactivity.  All nodes contain a copy of all user accounts (username and password). These are updated as soon as there is a change or at system start-up. All configuration and changes of this information needs to be made when the node has connection with a master. A node in standalone mode cannot change the username or password. 4.10 Integration into AEM When the repeater has been installed at site and the remote communication has been enabled, either through the repeater’s own modem or via an OMU, the repeater can be integrated to the Axell Element Manager. This is done by the operator of the AEM. After entering the telephone number to the repeater, the AEM dials up the repeater, downloads all the repeater parameters and statuses into a database. When all parameters have been downloaded, the AEM configures the repeater with the telephone number where alarms and reports should be sent, and optionally with a secondary telephone number where the repeater can dial in case connection to primary number fails. When heartbeat reports and alarms are sent from the repeater to the AEM also the latest information about the status and RF-configuration is included. This means that the AEM operator always has information about the current status in the AEM database (and do not need to call the repeater to find this out). Note! Once the repeater is integrated to the AEM, all changes to the repeater should preferably be done from the Axell Element Manager in order to ensure that the database always contains correct information. 4.11 Upgrading Firmware The software installed in the repeater is called firmware. Using the RMC it is possible to see what firmware is installed, install upgrades etc. The firmware can be upgraded in the field while the repeater is operational.   The RMC is used to upload software to the Control Module. Since the Control Module contains two separate software banks, software can be downloaded to one bank while executing from the other. Once software is successfully uploaded, the new software is executed. All repeater configurations remain unchanged when upgrading the software to a new version. The Control Module contains two different program banks. The software can be executed from one bank while new software is downloaded to the other. When new software has been completely downloaded, the execution is moved over to the new program bank. The software download can be done at site, or remotely via a modem. Note! During software download no measurements will be made in the repeater. However, the RF transmission will still be fully operational.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  63 (105)   Firmware Control via RMC View the currently installed firmware 1. Open the Firmware upload view in RMC. In the box labeled Installed Firmware information about the currently installed firmware is displayed. Upload new firmware 1. Open the Firmware upload view in RMC. In the box labeled Firmware Location select the directory where your firmware files (ARF files) are located. 2. Select the firmware to upload from the firmware list, labeled Select new firmware to upload. For each firmware available, there is information about version and compatibility with the repeater you are currently connected to. Below this list there is a box with detailed information about the selected firmware.  3. Click Start Upload. During upload a status screen displays upload progress information while you wait. The upload takes about 10 minutes with a local connection and 15 minutes over the GSM network. 4. Upload completed.  5. The user is logged out and the new firmware is initiated.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  64 (105)  5 Installation 5.1 Commissioning Advice 5.1.1 Introduction To set the proper operating RF levels on the repeaters in the MBF family during commissioning there are six steps to be carried out for each band of operation.  Set OMU DL attenuation to adjust the RF level from the BTS to suit the fibre optic converter in the OMU (UFO-M)  Run the OLA (Optical Link Adjustment) command for each band to correct for DL optical fibre loss  Set the DL attenuation in the repeater to adjust gain following fibre optic converter in the repeater (UFO-S)  Set the UL attenuation in the repeater to adjust gain before the fibre optic converter in the repeater (UFO-S)  Run the OLA (Optical Link Adjustment) command for each band to correct for DL optical fibre loss  Set OMU UL attenuation to adjust the OMU output level to suit the BTS    5.1.2 OMU Point of Interface (POI) The OMU will usually be fed from the donor BTS via an attenuator or coupling network. The electrical configuration of this OMU Point of Interface (POI) will be system specific depending on the presentation of the BTS RF ports, the power class of the BTS and whether the BTS itself provides coverage via antennas/radiating cable infrastructure or if coverage is only via the MBF repeaters.  The important consideration for commissioning is that the correct attenuation exists between BTS and OMU in order that   input power limits of OMU ports are not exceeded  operating levels can be brought into the correct range using the OMU internal attenuators  isolation is preserved between ports and bands  OMU damage levels are 10dBm RF in to the fibre optic converter. For some systems the commissioning adjustments may be completely independent (e.g. an MBF Tri Band repeater fed by separate OMUs, one per frequency band). For other systems (e.g. an MBF Tri Band repeater fed a by a single OMU carrying all three bands) one adjustment may affect all bands simultaneously. In such cases certain commissioning actions e.g. optical link adjustment only need to be carried out once for all bands but the POI must include some means to level the different frequency bands at the OMU interface ports.  5.1.3 Downlink POI / OMU DL Attenuator Adjustment The critical aspect for the correct system operating level is the composite power presented at the input of the fibre optic converter in the OMU (UFO-M). The illustration below shows the simplest possible arrangement for a single Tri Band repeater fed by three BTSs - one per band. It is assumed that the BTS for GSM900 and GSM1800 produce two carriers each of +43dBm and that the UMTS BTS produces a single carrier of +43dBm.  The correct interface level at the optical fibre converter is -5dBm/carrier in 900MHz and -7dBm/carrier in both GSM1800 and UMTS bands. An attenuation of 48dB in 900MHz and 50dB in 1800/UMTS is therefore required between them.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  65 (105)     MBF-T-9-18-22OMU #1UFOM #3UFOM #2RB2200BSBSUMTSRB900-17dB-19dBMCPA UMTS+40dB+24dB-1dB+18dBAtten=1Atten=4(Max Gain=25dB)+40dBMCPA GSM900-1.5dB-17dB-1dB-1dB-17dB-30dB-30dBUMTS:+43dBmGSM900:2x+43dBm0..10dB optical2x+12dBm(IL=16dB)(IL=14dB)(Max Gain=22dB)2x-5dBm2x-4dBm2x+35.5dBm2x+34dBm+12dBm-7dBm0dBm+40dBm+39dBmRB1800MCPA 1800Atten=5+40dB+20dB-1.5dB2x+35.5dBm2x-4dBm-19dB-1dB(IL=16dB)-17dBGSM1800:2x+43dBm2x-7dBm2x-24dBm2x-24dBm2x+12dBmUFOSAtten: 0-20dBPDPilot LevelUFOSAtten=3Det PwrUFOM #1LDPilot toneANTUFOSAtten: 0-20dBPDPilot LevelUFOSAtten: 0-20dBPDPilot Level2x-22dBm(Max Gain=25dB)-24dBmOMU #2UFOM #3UFOM #20..10dB opticalUFOSAtten=3Det PwrUFOM #1LDPilot toneOMU #3UFOM #3UFOM #20..10dB opticalUFOSAtten=3Det PwrUFOM #1LDPilot toneBSGSM1800-30dB
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  66 (105)  It must also be kept in mind that the OMU might have separated input/output ports for each band (UL/DL) while the interface with the BTS may well be duplex. In that case some duplexing network must be provided to allow these to be brought together. If there is more than one operator’s BTS per band the loss of any combining network and any equipment room cabling also becomes part of the overall attenuation required to reach the correct interface level in each frequency band. The illustration on the next page shows a more complicated arrangement where the same three BTSs feed multiple MBF repeaters (up to 6 is possible using the standard splitter card which fits the OMU rack). In this case an OMU per frequency band is shown. The internal splitter has an insertion loss of 14 or 16dB depending on frequency band. This loss is again a contribution to the overall attenuation which must be provided between BTS and the input ports of the UFO-M for the correct operational levels to be achieved. The interface levels must be modified to maintain the same composite power if a greater number of carriers is to be applied from the BTS.  The DL POI / OMU Adjustment must be made considering the fully loaded condition – e.g. a BTS capacity of 8 carriers must include a back off of 6dB compared to the 2 carrier level and -11dBm/carrier is then the correct UFO-M drive level for GSM 900. The same rule for back off applies in other bands.  Note that a UMTS BTS at idle (no traffic) will be radiating only a pilot – approx -10dB compared to the average power when it is in traffic. See also section about UMTS Signal Measurement below. 5.1.4 Repeater Downlink Optical Link Adjustment (OLA) The optical link between the UFO-M of the OMU and the UFO-S in the repeater is equipped with a calibrated pilot tone transmitter/receiver which enables compensation for the loss of the optical fibre plant between them. The OLA procedure requires a computer running Axell RMC software and an RS232 connection to the LMT Port of the repeater controller.  Start the RMC and login to the repeater as described in the appropriate section of the handbook. Click on the Actions tab on top of the RMC screen. A drop down list will appear where a command will be found to execute the optical link adjustment for each UFO-S module that is fitted to the repeater. Click the command for the desired optical link and following a short delay (2-3 secs) an information screen will be shown describing the result of the automatic setup process. This procedure is described in the OMU Manual section 4.10. 5.1.5 Downlink Repeater Gain Adjustment When the DL POI levels and the repeater optical links have both been set up as described in the foregoing the MBF repeater set at maximum gain should produce a composite signal level at the output connector of +37dBm for GSM900 and 1800 and +39dBm for UMTS. The RMC provides sub screens for each band where the downlink power from UFO-S optical receiver /input to the DL radio board and the composite output power level from the MCPA can be viewed.  The power amplifier for each frequency band can be enabled /disabled and the preset DL attenuation in the radio board for each band can be adjusted. A saturation status indicator (red/green) shows whether the radio board ALC is in operation. This indicator should be green. A red indication indicates overdrive the cause of which should be investigated and rectified.  In each band the DL output power per carrier should be measured using a spectrum analyzer. Allowing for the maximum DL carrier quantity in each band the composite level per band under full loading should be calculated to ensure it does not exceed the rated maximum otherwise ALC will be in operation when traffic levels are high. See also section about UMTS Signal Measurement below.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  67 (105)     OMUMBF-T-9-18-22UFOM #3UFOM #2RB2200BSBSGSM900UMTSRB900-17dB-19dB-4dBMCPA UMTS+40dB+28dB-1dB+22dBAtten=1Atten=4(Max Gain=29dB)+40dBMCPA GSM900+4dB-1.5dBSplit-17dB-1dB-1dB-17dB-30dB-30dBUMTS:+43dBmGSM900:2x+43dBm0..10dB optical2x+12dBm(IL=16dB)(IL=14dB)(Max Gain=26dB)2x-5dBm2x-22dBm2x-26dBm2x-4dBm2x+35.5dBm2x+34dBm+12dBm-7dBm-24dBm-28dBm0dBm+40dBm+39dBmRB1800MCPA 1800Atten=5+40dB+24dB-1.5dB-4dB2x+35.5dBm2x-4dBm-19dB-1dB(IL=16dB)-17dBGSM1800:2x+43dBm2x-7dBm2x-24dBm2x-28dBm(Max Gain=29dB)2x+12dBmUFOSAtten: 0-20dBPDPilot LevelUFOSAtten=3Det PwrUFOM #1LDPilot toneCombNetwANT
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  68 (105)  5.1.6 UMTS Signal Measurement The UMTS signal carries wideband and complex modulation and its properties vary depending on the level of traffic carried. 5.1.6.1 Bandwidth The first issue is the wideband nature of the signal. It occupies around 3.8MHz and measurements through a narrower filter will reduce the apparent power level since only a portion of the signal reaches the detector in the test equipment.  Equipment that includes a UMTS/3G measurement personality simplifies the task considerably. Usually a stored configuration for power measurement will integrate many samples taken using a narrower filter to display the correct power level for the bandwidth of the signal. Settings can easily become corrupted however leading to erroneous results. In such cases following the manufacturers instructions in detail is advised. Measuring with a simple spectrum analyzer must use a wider resolution bandwidth than 3.8MHz or else a bandwidth correction factor has to be applied to the observed result. E.g. if measuring with a 300kHz RBW the power level in the centre of the signal would appear to be around 11dB lower than actual (10Log 3.84/0.3). 5.1.6.2 Traffic A further complication is that the power level of a UMTS signal depends on the traffic level being carried. UMTS carrier power is usually quoted as average values e.g. a 5Watt or 37dBm signal can contain peaks up to 10dB greater when traffic is high. An idling base station carrying no traffic radiates only a Pilot in which case the power observed is around 10dB below the average value with traffic.  Advanced test equipment that can measure the different code power components in the UMTS signal avoids this problem but more often in the field repeater commissioning must be done when only simple test equipment is available. This leads to the need to know and allow for the state of traffic when making repeater setup and diagnostic measurements. It is obvious that adjusting a repeater to maximum rated output power by using BTSs that are idling radiating only the pilot will lead to overloading when they are in traffic.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  69 (105)  5.2 Install the Repeater 5.2.1 Unpack the Repeater Unpack the repeater   Inspect the shipped material before unpacking the equipment, document any visual damage and report according to routines. A delivery of a repeater from Axell Wireless contains:  Checklist with delivered items  Repeater  Mounting brackets  4 bolts for attaching repeater to mounting kit  Cable cover  Keys to repeater and insex tool for bolts  Hose for fibre inlet  CD containing User’s Manual and RMC  Any other specifically ordered item 5.2.2 Mount the Repeater  Mount the repeater on a wall, on a pole or in a rack           Mount the repeater in an accessible location and in a location that fulfils the environmental requirements.  The repeater can be mounted on the wall or in a 19 inch rack. The Repeater is delivered with mounting brackets.  The repeater needs to be mounted tightly to eliminate vibrations   Mounting bracket position for wall mounting Mounting bracket position for rack mounting     Ensure proper ventilation    Mount the repeater so that heat can be dispersed from it. The repeater wall mounting kit ensures an optimum airflow between the wall and the repeater itself. Do not block this air channel as it will cause the MTBF of the repeater to drop dramatically, or even in the worst case cause the repeater to fail completely.  If possible use a wall in the shadow to minimize the overall sun loading. If sufficient shielding cannot be obtained, an additional sun shield should be mounted.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  70 (105)   Example of a sun shield  IP65 Casing    Note! The repeater box should be closed using the two screws. The screws must be fully tightened. Failure to do so may affect the IP65 compliancy and therefore any warranty.  5.2.3 Ensure Proper Grounding Connect the grounding protection   Ensure that good grounding protection measures are taken to create a reliable repeater site. Make sure to use adequately dimensioned grounding cables. The minimum recommended conductive area for a grounding cable is 16mm2. The antenna cabling should be connected to ground every 10m by a reliable grounding kit.  Make sure the grounding product used is suitable for the kind and size of cable being used.  Connect the repeater box bolt to the same ground.  Ground Ground connector on repeater
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  71 (105)  5.2.4 Ensure Good EMV Protection   Caution If insufficient Electromagnetic Protection is provided,  or if EMV measures are not taken, warranties issued by Axell Wireless are not valid. Connect the lightning protection                                  The lightning hazard to electric and electronic equipment consists in the interferences of direct lightning current infections and high surge voltages induced by the electromagnetic field of nearby lightning channels or down conductors. Amplitudes from cloud-to-earth lightning amounts to several 10kA and may last longer than 2 ms. The damage caused depends on the energy involved and on the sensitivity of the electronics systems.  Ensure that lightning protection measures are taken to create a reliable repeater site. Protect all coaxial cables and power cables from the transients caused by lightning. Fit all cables with suitable lightning protection devices.   RepeaterFiberBTS-30dB CouplerOMUAntennaPrimary Protective DeviceEquipotential Grounding Bar230VAC/-48VDCProtective DeviceThe top of the mast must be higher than the antennas and be grounded properlyThe grounding path must have reliable continuity and be dimensioned correctlyBTS area Repeater area  Example of EMV protection for a repeater system  For detailed information please refer to IEC 61024-1 and 61312-1 for international standards for protection of information systems against LEMP, Lightning Electromagnetic Pulse, including radio transmitters. They define proper planning, installation and inspection of effective lightning protection systems.  The Axell Wireless repeaters comply with the EN standard ETS 301 498-8 which stipulates demands on lightning/surge protection for typical infrastructure telecom equipment installations.  Several lightning protection devices should be used in series with declining threshold voltages to help attenuate the pulse component which makes it through the first layer of protection. The primary protective device is part of the site installation and is not supplied by Axell
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  72 (105)       Wireless. Coaxial lightning protection is normally one of these three types: Gas capsule, High-pass and Bandpass. There also need to be a protective device installed on the power supply cord.  Protective device installed in connection with the  power supply   5.2.5 Attach Cabling Power Fiber inputGround Server antennaExternal alarms 5.2.5.1 Attach Fiber Cable This product is equipped with class 1 lasers, as per definition in EN 60825-1.  Caution Un-terminated optical receptacles may  emit laser radiation. Do not stare into beam  or view with optical instruments.  Note! Angled connectors, APC, need to be used throughout the whole link between  the OMU and the repeater. The angle needs to be 8 degrees.  Also the ODF connections need to be APC type.  The fibre must be monomode type.   Select fibre    Recommended fibre cable is single mode 9/125.  Connect the fibre    The casing of the repeater is equipped with an inlet. The inlet is designed to go with a corrugated hose, which is included in the shipment.  The hose, together with the rubber seal meet the protection standard IP65.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  73 (105)  1. Run the fibre through the hose   2. Run the fibre through the inlet in the repeater   3. Connect the fibre to the Fibre Optic Converter inside the repeater  4. Place the fibre in the rubber seal  5. Adjust the fibre length inside the repeater and insert the seal into the inlet  6. Attach the hose to the inlet  Note! Make sure the fibre is not bent too sharply inside the repeater. There is room under the optic module to allow for some slack of the fibre.  Note! To insert and extract the hose from the inlet press the side levers.     Make necessary measurements   Make necessary measurements to ensure a correct installation.  When the cable has been installed, the quality of the optical path should be checked for optical path loss and magnitude and location of any reflections. This can be done with an Optical Time Domain Reflectometer (OTDR). The total return loss should be > 45 dB. Optical reflections can degrade the noise and linearity of a fibre optic link. In particular, reflections that reach the laser can be a problem. Keep all discrete reflections to > 60 dB. The SC/APC connectors are polished to a return loss >60 dB.  Attach the fibre to the fibre optic  Note! Clean the fibre connector before it is connected, see instruction below.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  74 (105)  converter inside the repeater. Cleaning Optical Connectors Optical reflections from a discontinuity such as a poor connector interface appear on an RF spectrum analyzer trace as stable variations in the noise floor amplitude that are periodic with RF frequency. If the reflection is bad enough, it could impact the system performance. By far, the most common cause for a large discrete reflection is a dirty optical connector. A bit of dust or oil from a finger can easily interfere with, or block this light. Fortunately, it is very easy to clean the connector.  Be sure to use the correct procedure for the given connector. When disconnected, cap the FC/APC connector to keep it clean and prevent scratching the tip of the ferrule.  Alternative 1 Swipe the tip of the ferule 2-3 times with a cotton swab soaked in alcohol. Let it air dry.   Alternative 2 Use a product specially designed for the purpose.    5.2.6 Supply Power to the Repeater  Caution! The antenna cables must be connected to the repeater before mains power is switched on. Alternatively the antenna connections on the repeater can be terminated with 50ohm termination plugs.   Note! The repeater can be fed by 230 VAC 50 Hz, 115 VAC 60 Hz or -48 VDC. Ensure that the right voltage is used.  Connect the repeater to the power supply               Power is connected to the repeater via a plinth inside the repeater.  The strain relief fitting is a Pg 13.5 suitable for a 6-12 mm cable diameter. 230 VAC Power Supply Connect the power cable to the plinth with the phase linked to the brown cable, neutral linked to the blue and ground to the yellow/green. See illustration below.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  75 (105)                   Connection PlinthPhase/LiveNeutralGroundLNStrain Relief Fitting -48 VDC Power Supply Connect the power cable to the plinth with negative (-48V) to the uppermost connection and positive (0V) to the lower connection. Leave the middle connection empty. See illustration below.  Connection PlinthNegativePositive-48V0VStrain Relief Fitting  Recommended cable areas for 48VDC Distance  Cable Area 0 - 10 meters between repeater and power supply 2,5 mm² 10 – 50 meters between repeater and power supply 4 mm² Over 50 meters between repeater and power supply Recommendation is to reconfigure the installation, or to make special arrangements to increase cable area Requirements on 48 V DC power supply  The 48VDC power supply must comply with SELV requirements, as defined in EN60950, which implies double isolation. The output power needs to be 48VDC +25%/-15%.  The maximum input current is 8A. Turn Off level
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  76 (105)  The -48VDC version of the power supply is designed to turn off if the supply voltage falls below -36V (±1V), not to drain the feeding battery. It will turn on again as the supply voltage reaches -43V (± 1V).   Back-up battery   Backup Battery There is a back-up battery installed in connection with the power supply. If there is a power failure the battery will supply enough power to the Control Module and the Fibre Optic Converter in the repeater to send information about the power failure. The backup battery can be switched on and off separately. The switch is placed adjacent to the main power switch on the power supply. At delivery the back-up battery is connected.  The battery is replaced by lifting the battery pack out of the crate and disconnecting the cable.  Connector 5.2.7 Connect External Alarms  Connect external alarms  The repeater is equipped with an external alarm interface card. The connector plinth for the external alarms is located at the bottom of the repeater.  The strain relief fitting in is a Pg 13.5 suitable for a 6-12 mm cable diameter. Connect the alarm cords to the plinth according to the pin layout below (in the standard version pins 14 – 18 are not used).  1 External alarm 1A 2 External alarm 1B3 External alarm 2A 4 External alarm 2B 5 External alarm 3A 6 External alarm 3B 7 External alarm 4A 8 External alarm 4B 9 Alarm  +15V 10 Alarm  0V 11 Relay Output 1A  12 Relay Output 1B13 GND14 NC15 NC16 NC17 NC18 NCPin #    SignalPin 1
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  77 (105)  External Alarm  Four external alarm sources can be connected to the repeater. These alarms operate on a voltage between 12 and 24VDC. The presence or absence of this voltage will trigger the alarm depending on how the alarm polarity has been configured.  The alarms can be configured active-low or active-high, so that the alarm is given either in the presence or absence of applied power. Active high means that an applied voltage of between 12 and 24 V will cause the external alarm indicator to turn red. Active low means that when there is no voltage the alarm indicator will turn red. The repeater can supply +15 VDC to an external alarm source through pin 9 and 10. The maximum allowed load is 100mA. The repeater contains a relay (pin 11 and 12) that can be connected to an external device to indicate an alarm. The relay can be configured to trigger on any number of internal and external alarms. The maximum current that can be supplied is 100mA. 5.2.8 Close Repeater Close repeater  Close lid and lock repeater, or continue with the next section: Start-up the Repeater. Note! The two screws must be fully tightened. Failure to do so may affect the IP65 compliancy and therefore any warranty.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  78 (105)  5.3 Start-up the Repeater Caution!  Make sure the antenna cables or 50 ohm terminations are connected to the repeater’s antenna connectors before the repeater is turned on.  Switch the repeater on Switch the repeater on by using the power switches on the power supply.   Note! See caution above! Power Switch There are two switches. One is for the battery and one is for the power  The rightmost switch is the one that switches the main power. The leftmost is for turning the battery on/off. Note! The power switch has two positions; “on” and “stand by”. In the stand by position the repeater is still connected to the power supply but not operational. Note! On repeaters mounted in an extended box with two power supplies, both power supplies needs to be switched on.  Check power supply LEDs        Check the LEDs on the Power unit to ensure that normal operation conditions have been attained. Input Power+6V +15V +28V LED 1, Input Power, Green  Slow flash  Power supply unit operating on AC or DC OFF  Power supply unit not operating LED 2, +6V, Red Slow flash (every 10 seconds)  +6V power supply operating Quick flash  +6V power supply not operating or operating with malfunction LED 3, +15V, Red  Slow flash (every 10 seconds)  +15V power supply operating Quick flash  +15V power supply not operating or operating with malfunction LED 4, +28V, Red Slow flash (every 10 seconds)  +28V power supply operating Quick flash  +28V power supply not operating or operating
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  79 (105)   with malfunction  Examples Input Power+6V +15V +28V LED 1 is flashing slowly, LED 2 – 4 are flashing slowly (once every 10 seconds) => power supply unit is operating without problem Input Power+6V +15V +28V LED 1 is flashing slowly, one or two of  the red LEDs are flashing quickly => Input power is operating but there is a problem with some of the other voltages Input Power+6V +15V +28V LED 1 is flashing slowly, all of  the red LEDs are flashing quickly => Input power is out and unit is operating on backup battery   Check Control Module LEDs  The Control Module has four LEDs which give information regarding the status of the repeater and if someone is logged on to the repeater.  If the repeater is configured as a system slave the two LEDs MDM Power and MDM Status do not fill any function and can be disregarded. LOGINSTATUSMDM PWRMDM STATUS Blue LED - Login  Quick flash  Control Module switched on, someone logged in locally and/or remotely  Off (except for a quick flash every 10th second) Control Module switched on, no one logged in   Off  (permanent) Control Module switched OFF  Red LED - Status  Quick flash  Control Module switched on, one or more errors/alarms detected  Off (except for a quick flash every 10th second) Control Module switched on, status OK  Off  (permanent) Control Module switched off Green LED – Modem Power
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  80 (105)   On  Modem Power is on  Off  Modem Power is off   Green LED – Modem Status  On    Depending on type of call: Voice call: Connected to remote party Data call: Connected to remote party or exchange of parameters while setting up or disconnecting a call  Flashing  (irregular) Indicates GPSR data transfer. When a GPRS transfer is in progress the LED goes on within 1 second after data packets were exchanged. Flash duration in approximately 0.5s.  75ms on/75ms off/75ms on/3s off  One or more GPRS contexts activated  75ms on/3s off  Logged to network (monitoring control channels and user inRadio Modulections). No call in progress  600ms on/600ms off  No SIM card inserted, or no PIN entered, or network search in progress, or ongoing user authentications, or network login in progress  Off  Modem is off   Check the LEDs on the Fibre Optic Converter    The Fibre Optic Converter contains two optical alarm sources. These are alarms for transmitted and received optical signal level. The levels of the received optical signals can be monitored on-line via the RMC. This is convenient during installation and tuning of the system. There are 6 LEDs on the module to indicate the status. PWRERRUL DataDL DataOpto RxOpto Tx LED 1, Power, Green  On  Unit is powered on Off  Unit has no power LED 2, Error, Red On  Error detected Off  No error LED 3, UL Data, Yellow
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  81 (105)   On  Communication via the opto module is ongoing in the uplink direction Off  No communication LED 4, DL Data, Yellow On  Communication via the opto module is ongoing in the downlink direction Off  No communication LED 5, Opto Rx, Green On  Input opto level OK Off  Input opto level below threshold LED 6, Opto Tx, Green On  Output opto level OK Off  Output opto level below threshold
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  82 (105)  5.4 Initiate Local Communication 5.4.1 RMC Communication Connect to the LMT port  Connect the computer to the LMT port via a DB9 male connector with serial RS232 interface.  LMT Port  The communication parameters are set automatically by the RMC  Select “Cable” connection and communication port         Enter user name and password     Several users at a time can be logged on to a Repeater, for instance one locally via the RS232 interface and one remotely via modem or Ethernet.  There is one default user name and password defined for the repeater.. User Name  Password avitec  AvitecPasswd  Note! Both the user name and the password are case sensitive.   Note! Do not use the number pad when entering numbers.    Note! Failed login attempts are logged. Default maximum number is 8. It is decremented by one every hour, which means that it takes one hour after the last failed attempt before a new try can be made.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  83 (105)  5.4.2 RMC Work Views There are three different work views to choose from in the RMC  Console mode    The console mode displays a large number of repeater parameters and contains a number of console pages. It adjusts its user interface to adapt to the features of the connected repeater. Terminal mode     The terminal mode is used for communication with the repeater using its native command line interface. This interface follows the VT100 standard. For some special actions and error tracing, this mode gives an enhanced availability of the repeater. Firmware mode    The firmware mode is used for monitoring the currently installed software and for uploading new software to the repeater.  Note! The description in this manual is based on using the Consol work view.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  84 (105)  5.5 Install the OMU and Set up OMU-Repeater System For information about how to install the OMU which will supply the input signal to the repeater please refer to the OMU Manual. In the OMU Manual there is also information about how to calculate link budgets for a whole OMU-Repeater system.  5.6 Configure the Repeater The following pages will guide you through the configuration of a repeater utilizing the Repeater Maintenance Console (RMC) software. Configuration of a repeater is made partially on site and partially remotely through the AEM. At site the RF parameters are set and verified, the repeater is given a name (a tag) and the remote communication is set and verified. All other configuration can, and should be made from the AEM. 5.6.1 Set up RF Configuration Configuration of the repeater amplification can be made locally. If the repeater is connected to an OMU the configuration can also be made via this OMU. See OMU User’s Manual.  Note! This is an example from a single band repeater. Other repeaters will have similar features. Ensure online communication with the repeater     Select “RF/Status” window     Alarms and general information Uplink attenuation  Uplink input and output power  Downlink attenuation   Downlink input and output power      This shows a single band repeater with no RF signals  Check that the fibre is OK  Make sure there are no alarms relating to the fibre.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  85 (105)  Set attenuation level in uplink and downlink to a maximum  Choose the maximum attenuation value from the drop down menu.    Configure the downlink  -33  Lower the attenuation level step by step until the desired output power level is reached. In this example +33 dBm. Zero attenuation is the same as maximum gain. Note! Please also consult the OMU User’s Manual.   Initiate a fibre loss elimination  This is done from the OMU by sending a pilot tone to the repeater and calculating the loss in the fibre link. This loss is compensated for automatically. The system will behave as if there is no loss at all in the fibre link.  Configure the uplink    In the uplink direction the attenuation needs to be set based on a measurement of a known signal which is transmitted through the repeater and the OMU as well as the fibre. There are two ways of performing this measurement. Alternative 1 Use a signal generator to insert a signal of approximately -70dBm into the repeater’s server antenna port. Measure the signal level on the BTS or on the coupler and adjust the attenuation so that the total gain in the uplink is close to 0dB. (At 0dB gain the signal level at the coupler should be -40dBm and on the BTS -70dBm in this example.)  RepeaterSignal GeneratorFiber-70dBmBTS-30dB CouplerOMU-40dBm-70dBmAlternative 2: Use the RMC to measure the uplink at the OMU  Alternative 2 Use a signal generator to insert a signal of approximately -70dBm into the repeater’s
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  86 (105)  server antenna port. Log into the OMU and monitor the uplink via the RMC. This measurement is not as accurate as alternative 1.  Note! If several repeaters are connected to the same OMU the total gain in each chain should be slightly lower than 0dB not to insert too much noise into the BTS.  Note!   For in-depth instructions for commissioning of an OMU-Repeater system please contact your Axell Wireless representative.  5.6.2 Set Repeater Name (TAG) The TAG can be chosen freely to give the repeater a name that is linked to the location, the site name, etc. The TAG may contain up to 30 characters including spaces. Select “Configuration” and “Product”           Insert the repeater’s name (TAG) in this box.    Note! Do not assign an ID. The AEM will do this automatically when the repeater is integrated in the AEM. 5.6.3 Configure Alarms  See section 4.4.7Alarm Configuration.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  87 (105)  5.6.4 Configure Reports Select “Configuration” and “Reports”        Set report data   Heartbeat   Alarms   Note! For repeaters that are to be used as slaves in an OMU-Repeater system all report configurations are done from the OMU.  5.7 Set Up Remote Communication Note! If the repeater is fibre fed and is set up as a slave- this section is not relevant since the remote communication is handled by the node master – in most cases an OMU. The repeaters can be configured with a wireless modem, a PSTN modem or Ethernet for the remote communication.  5.7.1 Communication via Modem The Control Module is responsible for enabling the power to the modem, unlocking the SIM-card, using the configured PIN-code and making sure the modem is logged in to the network correctly. Depending on network configuration and modem usage, the modem might require different modem initialization strings to work properly. This modem initialization string is set and verified during repeater setup.  5.7.1.1 Modem Initialization After a power failure, or upon user request, the Control Module performs a full initialization of the modem. This consists of three steps:  If the SIM-card in the modem has the PIN code enabled, the Control Module unlocks the PIN code. In case wrong PIN-code is configured, the Control Module will not try to unlock the SIM again until the PIN-code is changed. This avoids the SIM card being locked by a Control Module repeatedly trying to unlock the SIM with the wrong PIN code.  Once the SIM is unlocked, the Control Module waits for the SIM to log in to the network. Depending on signal quality and network configuration this might take a while. The Control Module will wait a configurable number of seconds (default 50 seconds) for the modem to login to the network. In case no network is found, a modem power cycle will be initiated. When the modem is successfully logged in to the network, the Control Module configures the modem with the modem initialization string as configured when setting up the remote configuration. The modem initialization string is a network dependent string. The default string is suitable for most networks, but some networks might require some tweaking of this string.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  88 (105)  5.7.1.2 Monitoring Modem Connection The Control Module constantly monitors the status of the modem connection to ensure that it is working properly, and that the modem is logged in to the network. In case the modem is not registered to the network, or the Control Module cannot properly communicate with the modem, a power cycling of the modem is initiated, after which the modem will reinitialized. 5.7.1.3 Scheduled Modem Power Cycling In addition to polling the modem to ensure the repeater online status, the Control Module can be configured to perform an automatic power cycling on a scheduled time of the day. Power cycling the modem ensures the latest network configuration for the modem, such as the HLR Update Interval etc.  Note! By default, the scheduled modem power cycling is disabled. 5.7.2 Communication via Wireless Modem  There are two different ways of communication for a wireless (GSM) modem:  Using data call / modem connection.  Note! This requires the SIM-card in the modem to be configured with data service.  Using SMS to configure the repeater with simple text messages  Note! SMS functionality is not implemented in this SW release. The Axell Element Manager always uses data call communication with the repeater, why all repeaters being controlled by the AEM must have data service enabled on the SIM card. Configuring the repeater to send alarms and reports via SMS it is still possible to establish data calls to the repeater, as long as the SIM card is data service enabled. 5.7.2.1 Modem Configuration, not using GPRS Select “Configuration” and “Communication”           Select Data Call   Initialization string  Connect times      AEM addressed are set via the AEM  2004-01-01 Select Data Call  Set the modem initialization string. This string differs between networks. Primary
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  89 (105)  recommendation is AT+CBST=71,0,1;\Q3. If remote communication cannot be established try 7,0,1 or 0,0,1 or 7,0,3. For more information please refer to the section on Troubleshooting Remote Communication. Tick “Enable Automatic Modem Power Cycling” for the modem to be power cycled once every 24 hours. Set the time at which the modem should be tested. This function ensures that the repeater always is logged in to the network.  5.7.2.2 Modem Configuration, using GPRS Select “Configuration” and “Communication”           Select GPRS  Initialization string  Connect times      AEM addressed are set via the AEM  Configure GPRS    Select GPRS Set the modem initialization string. This string differs between networks. Primary recommendation is AT+CBST=71,0,1;\Q3 Tick “Enable Automatic Modem Power Cycling” for the modem to be power cycled once every 24 hours. Set the time at which the modem should be tested. This function ensures that the repeater always is logged in to the network. Click on Configure…
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  90 (105)       Each parameter is described in Common Commands and Attributes, section 14 GPRS Configurations. Set the Access Point Name. It needs to be defined by the telecom operator Set Maximum Receive Unit and maximum Transmission Unit. These differ depending on access type: 576 for GSM, 1476 for EDGE and 1500 for WCDMA. Click on Close, and then on “Yes”.  Wait for the modem to restart. This can take a few minutes.  When the modem settings are ready the LED turn green.    5.7.2.3 AEM Addresses The Control Module can be configured with two different addresses (telephone numbers) to which alarms and reports are delivered. In case the repeater cannot deliver alarms and reports to the primary address, the next call will be made to the secondary address.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  91 (105)  A fallback functionality is available, which means that the Control Module falls back to the primary address after a configurable number of minutes. If this interval is set to 0, the fallback will not be performed. A user can always force the Control Module to fall back to the primary address. Note! When the repeater is integrated to the Axell Element Manager system, these addresses are set by the AEM, why they need not be configured during site installation. 5.7.2.4 Modem Verification When the remote configuration has been set up the communication can be verified using the modem feature of the RMC and dialling the data number. The remote communication is verified as soon as a successful remote login to the repeater has been performed. However, as a first step, it is recommended to verify that the modem is initialized correctly. After configuring the modem using the RMC, make sure to initiate a power cycling of the modem. This is done from the RMC menu. Click on the drop-down menu Actions, choose Power Cycle Modem on Logout   An immediate power cycling is initiated after which the modem is initialized and registered onto the network. The modem is now ready for remote access. Ensure a successful configuration by observing the modem LED as described below.  Note! This LED behaviour is valid only for GSM modems. Other modem types will be added in later editions. Green LED – Modem Status  On    Depending on type of call: Voice call: Connected to remote party Data call: Connected to remote party or exchange of parameters while setting up or disconnecting a call  Flashing  (irregular) Indicates GPSR data transfer. When a GPRS transfer is in progress the LED goes on within 1 second after data packets were exchanged. Flash duration in approximately 0.5s.  75ms on/75ms off/75ms on/3s off  One or more GPRS contexts activated  75ms on/3s off  Logged to network (monitoring control channels and user interactions). No call in progress  600ms on/600ms off  No SIM card inserted, or no PIN entered, or network search in progress, or ongoing user authentications, or network login in progress  Off  Modem is off  Verify the remote communication either by having someone attempting to integrate the repeater from the Axell Element Manager, or by dialling the repeater using the Repeater Maintenance Console.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  92 (105)  Note! It is very important to dial the data number of the SIM. In case the voice number is dialled, the call is answered, but almost immediately the call will be hung up. 5.7.2.5 SIM-card Using Single Numbering Scheme If the network is configured using Single Numbering Scheme (SNS), some special considerations apply. The repeaters are by default configured so that networks using SNS always will have calls routed to the data service in the modem. When dialling from within the network to a repeater having an SNS-configured SIM will operate normally, since the call originator informs the system that the bearer is of type DATA. However, when dialling from outside the network trying to connect to the repeater can be difficult. Depending on the interface to the roaming network or to the PSTN network if an analogue modem is used, the bearer type can default to voice. If the bearer is set to voice, the data service cannot be converted to DATA, and a call setup cannot be completed.  Note! This is not a repeater related problem; the solution is to verify how the external network interfaces handles the VOICE vs. DATA bearer type. 5.7.3 Configuration via PSTN (Fixed) Modem Also for PSTN modems data call shall be used.  Select “Configuration” and “Communication”           Select Data Call   Initialization string  Connect times      AEM addressed are set via the AEM  2004-01-01ATE0S0=0  Tick “Enable Automatic Modem Power Cycling” for the modem to be power cycled once every 24 hours. Set the time at which the modem should be tested. This function ensures that the repeater always is logged in to the network. 5.7.4 Communication via TCP/IP and Ethernet A TCP/IP communication is run over a company’s network. Therefore each company needs to define the details regarding the configuration, IP addresses, etc. For more information please refer to Common Commands and Attributes, section 13 Network Configurations.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  93 (105)  Select “Configuration” and “Communication”                 Set IP address and other relevant information here    In these screens the Ethernet and/or DNS Gateway parameters can be set         5.7.5 Troubleshooting Remote Communication Please also refer to the document Common Command and Attributes for guidance.  Since many networks have their own “personality”, performing first time configuration of the remote communication sometimes requires tweaking of the modem parameters. This section describes some trouble shooting techniques if configuring the repeater for remote access fails.  The illustration below is a simplified schematic of the remote communication between a GSM modem in a repeater and an analogue modem. The analogue modem in the computer communicates with the Interworking Function Unit (IFU), which is the GSM network analogue network interface. The call is routed via the switch centre over the air interface to the data call number in the SIM-card of the GSM module. The Control Module is responsible for establishing connections with the Axell Element Manager, and to answer incoming calls to the repeater.  As described in previous sections, the Control Module only accepts one login at a time, either via Local Maintenance port (LMT) or modem connection. Hence, when verifying the remote access of the repeater, it is important to log out from the repeater locally before trying to access the repeater remotely.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  94 (105)  Radio LinkProtocol(RLP)Base StationLaptopLaptopControl module in Axell Wireless  RepeaterSwitch CentreModemModem RS232InterworkingFunction Unit(IFU)  5.7.5.1 Direct Modem Access To allow for advanced trouble shooting of the communications, it is possible to access the modem directly via the Control Module from a laptop computer.   LaptopLaptopRS232 cableControl ModuleGSM ModuleLMT Port Log in to the repeater, either with RMC, or with a terminal emulation program, such as HyperTerminal™. When the login is completed, select Terminal Mode, this will give access to the repeater command prompt in the same way as with HyperTerminal. When the repeater prompt is accessible, type in the command  ACCESS MODEM <Enter>.  When typing ACCESS MODEM, the controller will send all the characters that are typed directly out to the modem port. All characters replied back from the modem will go directly to the LMT port and back to the computer. To abort an ACCESS MODEM session, press three ‘-‘ in a row (all three within one second) to come back to the repeater command prompt. Note! When accessing the modem port the modem might be configured with “echo off”, meaning that the characters entered will not be echoed back to the screen. In order to enable “echo”, press Enter.  Type  ATE1 <enter> (invisible)  The modem replies with OK indicating that the echo is enabled. All characters entered will now be echoed back to the terminal program. 5.7.5.2 Trace Modem For troubleshooting purposes it is possible to trace the actual progress of initializing the modem. This trace is useful when having problems with the modem initialization. Go to Terminal Mode and type TRACE MODEM
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  95 (105)    To end session type CTRL-Z 5.7.5.3 Manually Answering Incoming Calls It is possible to manually answer incoming calls without involving the repeater software at all, to verify that the remote access and the network itself works as intended. In order to verify the remote communication, make sure to have someone stand by to dial up the repeater with a terminal emulation program, for example HyperTerminal™. Go in to Direct Modem Access as described earlier. When in direct access mode, ask the person standing by to dial up the repeater. As soon as a call is received, the text RING will repeatedly be displayed on the screen.  Type ATA <enter> This will inform the modem to answer (ATtention Answer).  When the connection is established, a connect message will be displayed including the connection speed. Sometimes the information comes together with some miscellaneous information, such as error correction protocols etc.  Note! Make sure the remote peer dials the Data Call number If the voice number is dialled instead of the data number, or if the modem contains an illegal modem initialization string, the message  OK or NO CARRIER  will be displayed almost immediately.  Try to change the modem initialization string. The modem initialization string mainly used to configure the remote communication is AT+CBST.  Successful modem initialization strings used by Axell Wireless includes (most common first): AT+CBST=71,0,1;\Q3 AT+CBST=7,0,1;\Q3 AT+CBST=0,0,1;\Q3
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  96 (105)  AT+CBST=0,0,1;\Q3 AT+CBST=7,0,3;\Q3 Once the modem initialization string is entered, try again to dial up the repeater. For details on the different modem initialization strings, please refer to the modem’s user guide. If the setup is successful, the connect message will be brought up; CONNECT 9600 This means that an online connection is established to the remote peer. From now on, all characters typed on the keyboard will end up on the remote peer’s screen. Similarly, all characters typed by the remote peer will be displayed on the screen.  In the example, the incoming call was successfully answered, and the remote user entered the text message.   In order to come back to modem command mode, press +++ (three pluses) rapidly (within one second).  Receiving OK means that the modem is back in command mode. Type ATH <enter>  This terminates the connection to the remote peer. The message NO CARRIER will be displayed.  5.7.5.4 Common Problems  Problem 1 When enabling the remote access for the repeater, the modem fails to log in to the network. Solution Signal strength from the donor site is too low. The signal strength can be read directly from the modem. Go in to Direct Modem Access as described earlier. Use the command AT+CSQ (documented below) to read out the signal strength. In order to have good signal quality, Axell Wireless recommends that the signal strength should be better than -95 dBm. If signal strength is lower, try to adjust the antennas to get a better signal strength from the donor.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  97 (105)   Documentation of +CSQ command from a modem’s manual.   In the example the reply to AT+CSQ is 0,7 meaning 7*2 dB above -113 dBm; the modem detects a signal level of -99 dBm.   Problem 2a Repeater is configured properly, and answers the incoming call, but when trying to dial the repeater using an analogue mode, no modem handshaking is heard from the dialling modem.  Problem 2b When dialling the repeater, the repeater answers the incoming call, but no connection is established, and after a while the repeater disconnects the call.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  98 (105)  Solution   The most common cause is that the number called is the voice number of the SIM, not the data number. Therefore, make sure to dial the data number. If data call is used, the problem probably is an illegal modem initialization string. In order to change the modem string, go to the repeater command prompt. Try changing the modem initialization string and log out to let the controller reinitialize the modem. If problem remains, try a few different modem initialization strings. Axell Wireless has been successful with the following modem initialization strings: AT+CBST=71,0,1;\Q3 AT+CBST=7,0,1;\Q3 AT+CBST=0,0,1;\Q3 AT+CBST=0,0,1;\Q3 AT+CBST=7,0,3;\Q3 Please refer to the modem manual for detailed description of the modem initialization strings. Problem 3 It is possible to call the repeater from another GSM mobile, but not from an analogue modem.  Solution This problem is most likely related to the modem configuration and/or the configuration of the IFU unit. Try to decrease the communications speed and make sure that the modem error correction is supported by the IFU. Verify the IFU configuration to see if there are any known problems with the modem connections. Problem 4 When dialling the repeater, or when the repeater is dialling the Element Manager, the connection is terminated before the handshaking is completed. Solution When a repeater is answering an incoming modem call, or calling up the OMC to deliver an alarm or a report, the repeater will wait a configurable number of seconds for the call to be established. If no communication is established within this time, the call will be hung up. If this interval is set too low, the handshaking is terminated too fast. In the RMC, verify the Modem Connect Time to see that it is set to at least 30 seconds. 5.8 Integration into the AEM When the repeater has been installed at site and the remote communication has been enabled, the repeater can be integrated to the Axell Element Manager. This is done by the operator of the AEM. After entering the telephone number to the repeater, the AEM dials up the repeater, downloads all the repeater parameters and statuses into a database. When all parameters have been downloaded, the AEM configures the repeater with the telephone number where alarms and reports should be sent, and optionally with a secondary telephone number where the repeater can dial in case connection to primary number fails. When heartbeat reports and alarms are sent from the repeater to the AEM also the latest information about the status and RF-configuration is included. This means that the AEM operator always has information about the current status in the AEM database (and do not need to call the repeater to find this out). Note! Once the repeater is integrated to the AEM, all changes to the repeater should preferably be done from the Axell Element Manager in order to ensure that the database always contains correct information.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  99 (105)  6 Maintenance Caution Please be aware that the equipment may, during certain conditions become very warm and can  cause minor injuries if handled without any protection, such as gloves.  Caution Risk of explosion if battery is replaced by an incorrect type.  Dispose of used batteries according to local laws and instructions.  This product is equipped with class 1 lasers, as per definition in EN 60825-1.  Caution Un-terminated optical receptacles may  emit laser radiation. Do not stare into beam  or view with optical instruments. 6.1 General The system normally operates without any operator intervention or maintenance. If in the unlikely event of any unit failure, the faulty repeater should be replaced. A failed unit can be removed and replaced with a spare while the rest of the system (other repeaters) is still operating. However, the power supply of the failed repeater should be isolated from the power before anything is replaced. In the event of a malfunction in the system, the status of the antenna systems as well as the continuity of the cabling should be checked before replacing any modules within the repeater. 6.2 Preventative Maintenance The repeater does not require preventative maintenance apart from changing the battery once every three years. 6.3 Trouble Shooting In the event of a failure Axell Wireless’s support service should be contacted for advice on a possible module replacement or other action to be taken. Caution! If a shipment of a repeater back to Axell Wireless is made within the period of  guarantee the original packing must be used. 6.4 Component Replacement None of the modules in the repeater can be replaced without removing the repeater from its mounting and opening the cover of the repeater.  6.5 Product Disposal Disposal of this product must be handled according to all national laws and regulations. For detailed information regarding materials, please refer to Axell Wireless.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  100 (105)  7 Specifications Note! All data is subject to change without prior notice. 7.1 Single Band Repeater MBF-S-7/8/9/17/18/19/22 Electrical Specifications   LTE 700  GSM/WCDMA 850 E-GSM GSM1800  GSM/WCDMA 1900 AWS  WCDMA2100 UL  698-716MHz and  777-787MHz 824 – 849 MHz  880 – 915 MHz  1710 - 1785 MHz 1850 - 1910 MHz 1710-1755 MHz 1920 - 1980 MHz DL  728-756MHz  869 – 894 MHz  925 – 960 MHz  1805 - 1880 MHz 1930 - 1990 MHz 2110-2155 MHz 2110 - 2170 MHz Operational bandwidth 28MHz/18MHz/ 10MHz 25MHz  35 MHz 75MHz  60 MHz  45MHz  60 MHz Composite Output Power DL +37dBm  +37 dBm  +37 dBm +37 dBm  +37 dBm  -39 dBm (for PAR of 8.5 dB) +39 dBm (for PAR of 8.5 dB)    Ripple in pass band (all bands)  < 2 dB  Noise figure UL (all bands)  3 dB typical (maximum gain) Propagation delay (all bands)  < 2 µs   Modulation Accuracy at nominal output power LTE  <3%EVM RMS GSM / GMSK   < 2.5 ° RMS and < 10 ° peak  EDGE / 8-PSK   < 3 % EVM RMS WCDMA/EVM  < 12.5% RMS (composite according to ETSI TS 25.106 with TM 1/64 DPCH)  WCDMA/PkDCE                                                        < -33 dB (according to ETSI TS 25.106 with TM 1/64 DPCH and spreading factor 256)  Gain UL/DL (all bands)  Adjustable in 1 dB steps   System Impedance  50 ohm Return Loss at Antenna Connection  > 14 dB    Antenna connectors  DIN 7/16 Electrical ratings  230 VAC, 50 Hz or -48 VDC Power Consumption   140 W
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  101 (105)  Optical Module Electrical Specification  Laser class  Class 1 Optical power level   +3dBm ±2dBm  Optical Wavelength   Two colour system  Three colour system  Four colour system Master  1310 ± 10 nm  1310 ± 10 nm  1310 ± 10 nm Slave 1  1550 ± 3 nm  1550 ± 3 nm  1530 ± 3 nm Slave 2  NA  1510 ± 3 nm  1510 ± 3 nm Slave 3  NA  NA  1550 ± 3 nm     Mechanical Specifications Dimensions   540 x 350 x 150 mm Enclosure  Aluminium (IP 65) Weight   20 kg Environmental Specifications Cooling  Convection* EMC   See compliance below  Operating Temperature  - 25 to + 55 ° C Storage   - 30 to + 70 ° C Humidity  ETSI EN 300 019-2-4 (see compliance below)      MTBF   > 100 000 hrs  Complies in applicable parts, relevant on different markets, to: R&TTE Directive including ETS EN 301 502 (ETS EN 300 609-4/GSM 11.26) ETSI TS 25.106, ETSI 25.143 ETSI EN 301 908-11 ETS EN 301 498-8 EN 60 950 EN 50 385      * The MBF repeaters are designed primarily for multi carrier purposes. If the repeaters are run at full output power over a longer period the convection cooling might not be enough. The repeaters have a power management function implemented that will step down the power and if needed fully shut down the amplifier chains until temperature has reached normal values. In situations where a repeater will be run in such a manner extra cooling can be provided for instance by putting the repeater in a temperature controlled environment or via external fans.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  102 (105)  7.2 Dual Band Repeater MBF-D-9-22/8-19/7-17 Electrical Specifications   LTE 700  GSM/WCDMA 850 E-GSM  GSM/WCDMA 1900 AWS  WCDMA2100 UL  698-716MHz and  777-787MHz 824 – 849 MHz  880 – 915 MHz  1850 - 1910 MHz  1710-1755 MHz 1920 - 1980 MHz DL  728-756MHz  869 – 894 MHz  925 – 960 MHz  1930 - 1990 MHz  2110-2155 MHz 2110 - 2170 MHz Operational bandwidth 28MHz/18MHz/ 10MHz 25MHz  35 MHz  60 MHz  45MHz  60 MHz Composite Output Power DL +37dBm  +37 dBm  +37 dBm +37 dBm  -39 dBm (for PAR of 8.5 dB) +39 dBm (for PAR of 8.5 dB)  Ripple in pass band (all bands)  < 2 dB  Noise figure UL (all bands)  3 dB typical (maximum gain) Propagation delay (all bands)  < 2 µs   Modulation Accuracy at nominal output power LTE 700  <3% EVM RMS GSM / GMSK   < 2.5 ° RMS and < 10 ° peak EDGE / 8-PSK   < 3 % EVM RMS WCDMA/EVM  < 12.5% RMS (composite according to ETSI TS 25.106 with TM 1/64 DPCH)  WCDMA/PkDCE                                                        < -33 dB (according to ETSI TS 25.106 with TM 1/64 DPCH and spreading factor 256)  Gain UL/DL (all bands)  Adjustable in 1 dB steps   System Impedance (all bands)  50 ohm Return Loss at Antenna Connection  > 14 dB    Antenna connectors  DIN 7/16 Electrical ratings  230 VAC, 50 Hz or -48 VDC Power Consumption   220 W
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  103 (105)  Optical Module Electrical Specification  Laser class  Class 1 Optical power level   +3dBm ±2dBm  Optical Wavelength   Two colour system  Three colour system  Four colour system Master  1310 ± 10 nm  1310 ± 10 nm  1310 ± 10 nm Slave 1  1550 ± 3 nm  1550 ± 3 nm  1530 ± 3 nm Slave 2  NA  1510 ± 3 nm  1510 ± 3 nm Slave 3  NA  NA  1550 ± 3 nm     Mechanical Specifications Dimensions   540 x 350 x 150 mm Enclosure  Aluminium (IP 65) Weight   22 kg Environmental Specifications Cooling  Convection* EMC   See compliance below  Operating Temperature  - 25 to + 55 ° C Storage   - 30 to + 70 ° C Humidity  ETSI EN 300 019-2-4 (see compliance below)      MTBF   > 100 000 hrs  Complies in applicable parts, relevant on different markets, to: R&TTE Directive including ETS EN 301 502 (ETS EN 300 609-4/GSM 11.26) ETSI TS 25.106, ETSI 25.143 ETSI EN 301 908-11 ETS EN 301 498-8 EN 60 950 EN 50 385  * The MBF repeaters are designed primarily for multi carrier purposes. If the repeaters are run at full output power over a longer period the convection cooling might not be enough. The repeaters have a power management function implemented that will step down the power and if needed fully shut down the amplifier chains until temperature has reached normal values. In situations where a repeater will be run in such a manner extra cooling can be provided for instance by putting the repeater in a temperature controlled environment or via external fans.
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  104 (105)  7.3 Tri Band Repeater MBF-T-9-18-22/8-17-19 Electrical Specifications   GSM/WCDMA 850 E-GSM  GSM1800  GSM/WCDMA 1900 WCDMA 2100 AWS UL  824 – 849 MHz  880 – 915 MHz  1710 - 1785 MHz 1850 - 1910 MHz 1920 - 1980 MHz 1710-1755 MHz DL  869 – 894 MHz  925 – 960 MHz  1805 - 1880 MHz 1930 - 1990 MHz 2110 - 2170 MHz 2110-2155 MHz Operational bandwidth 25MHz  35 MHz  75MHz  60 MHz  60 MHz  45MHz Composite Output Power DL +37 dBm  +37 dBm*  +37 dBm*  +37 dBm  +39 dBm (for PAR of 8.5 dB) +39 dBm (for PAR of 8.5 dB)  * In repeaters that share a common downlink fibre for 900MHZ and 1800MHz a minimum of 4 carriers in each band is required for the full composite output power to be attainable maintaining full ETSI compliance  Ripple in pass band (all bands)                                    < 2 dB  Noise figure UL (all bands)  3 dB typical (maximum gain) Propagation delay (all bands)     < 2 µs   Modulation Accuracy at nominal output power GSM / GMSK                                                     < 2.5 ° RMS and < 10 ° peak EDGE / 8-PSK                                             < 3 % EVM RMS  WCDMA/EVM  < 12.5% RMS (composite according to ETSI TS 25.106 with TM 1/64 DPCH)  WCDMA/PkDCE                                                        < -33 dB (according to ETSI TS 25.106 with TM 1/64 DPCH and spreading factor 256)  Gain UL/DL (all bands)                  Adjustable in 1 dB steps   System Impedance                                               50 ohm Return Loss at Antenna Connection  > 14 dB    Antenna connectors                                             DIN 7/16 Electrical ratings                                                  230 VAC, 50 Hz or -48 VDC Power Consumption                                         350 W
    MBF, Multi Band Repeater                                     PRODUCT DESCRIPTION AND USER'S MANUAL   © Axell Wireless Ltd  A 200 93 00, rev E  105 (105)  Optical Module Electrical Specification  Laser class  Class 1 Optical power level   +3dBm ±2dBm Optical Wavelength   Two colour system  Three colour system  Four colour system Master  1310 ± 10 nm  1310 ± 10 nm  1310 ± 10 nm Slave 1  1550 ± 3 nm  1550 ± 3 nm  1530 ± 3 nm Slave 2  NA  1510 ± 3 nm  1510 ± 3 nm Slave 3  NA  NA  1550 ± 3 nm  Mechanical Specifications Dimensions                                                    540 x 350 x 220 mm Enclosure                                                              Aluminium (IP 65) Weight                                                                        33 kg Environmental Specifications Cooling  Convection* EMC                                                                            See compliance below  Operating Temperature                                      - 25 to + 55 ° C Storage                                                            - 30 to + 70 ° C Humidity  ETSI EN 300 019-2-4 (see compliance below)                         MTBF                                                          > 100 000 hrs  Complies in applicable parts, relevant on different markets, to: R&TTE Directive including ETS EN 301 502 (ETS EN 300 609-4/GSM 11.26) ETSI TS 25.106, ETSI 25.143 ETSI EN 301 908-11 ETS EN 301 498-8 EN 60 950 EN 50 385    * The MBF repeaters are designed primarily for multi carrier purposes. If the repeaters are run at full output power over a longer period the convection cooling might not be enough. The repeaters have a power management function implemented that will step down the power and if needed fully shut down the amplifier chains until temperature has reached normal values. In situations where a repeater will be run in such a manner extra cooling can be provided for instance by putting the repeater in a temperature controlled environment or via external fans.

Navigation menu