PCB Piezotronics IMI673A01 Receiver User Manual Echo Reciever Manual 2011 06 29

Download:
Mirror Download [FCC.gov]
Document ID	1530711
Application ID	dkcS0vSutAZy4/p3Jtr0hw==
Document Description	User's Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	34.32kB (428969 bits)
Date Submitted	2011-08-26 00:00:00
Date Available	2011-08-26 00:00:00
Creation Date	2011-07-15 07:43:11
Producing Software	GPL Ghostscript 8.70
Document Lastmod	2011-07-15 07:43:11
Document Title	Echo_Reciever_Manual_2011-06-29
Document Creator	PDFCreator Version 0.9.9
Document Author:	dcorelli

Echo® Wireless Receiver
Installation and Operation Manual
Page 1 of 9
Table of Contents
Introduction......................................................................................................................... 4
Proper Handling .................................................................................................................. 4
Receiver Connections ......................................................................................................... 5
Connection A – MIL Connector .................................................................................. 5
Connection B – Industrial Ethernet ............................................................................ 6
Connection C – N Antenna Connection ...................................................................... 6
Locating and Installing the Receiver .................................................................................. 6
Programming the Receiver ................................................................................................. 7
Setting a static or dynamic IP ...................................................................................... 7
Page 2 of 9
FCC NOTICE
FCC ID: ZOC-IMI673A01
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
INDUSTRY CANADA (IC) NOTICE
IC: 9732A-IMI673A01
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Page 3 of 9
Introduction
The Echo® Receiver is a one-way communication wireless receiver operating in the 902928 MHz ISM Band used for the condition monitoring of plant equipment. The receiver
continuously awaits the receipt of intermittent transmissions from Echo® Wireless
Vibration Sensors and EchoPlus® Wireless Junction Boxes. The Echo® Receiver is
connected to a computer or network running Microsoft® SQL database and Echo® Data
Server Software. Information received by the receiver is placed into the Microsoft® SQL
Database where it can be manipulated by the Echo® Data Server software. For
information on the setup and installation of the Echo® Wireless Vibration Sensors,
EchoPlus® Wireless Vibration Junction Boxes, or the Echo® Data Server please consult
their respective manuals.
Proper Handling
Proper handling of the Echo® Receiver is critical to preventing damage.
The following should be avoided:
• Removing the cover of the receiver.
• Dropping the receiver.
• Submersing or spraying the receiver with fluids of any kind.
• Using excessive torque when mounting the unit.
• Placing the unit in strong magnetic fields.
• Exposing the unit to temperatures above 158° F or below -4° F.
Warning
Do not attempt to remove the cover of the Echo® Wireless Receiver.
There are no customer serviceable components inside.
Removing the cover will void the warranty.
Page 4 of 9
Receiver Connections
The Echo® Wireless Receiver is equipped with 4 connectors including 2 MIL, 1 industrial
Ethernet, and 1 N antenna connector. Labels for these connector are found on the bottom
of the receiver.
Both MIL connectors can be used interchangeably for power or data
transmission.
Tip
Location
Connector Type
MIL
Industrial Ethernet
Function
Power Cable or
Programming Cable
Network Cable
Antenna
Quantity
Connection A – MIL Connector
The MIL connections are completely interchangeable. These connections are used for
two purposes. The first is the power for the Receiver unit. A supplied power adaptor has
a mating MIL connector and powers the unit with 110-220VAC line power. If power is
connected to the receiver the blue LED will light indicating the unit is on.
Page 5 of 9
DO NOT USE ANY POWER SUPPLY OTHER THAN THE ONE
INCLUDED WITH THE RECEIVER! DO NOT SUPPLY POWER
OTHER THAN 110-220 VAC OR DAMAGE WILL OCCUR.
Caution
The MIL connector is also used for programming and updating the Echo® Receiver. A
special RS232 to MIL connector cable (optional) connects a computer to the receiver.
For specific information on how to program or update the receiver, consult the
“Programming the Receiver” section of this manual.
Connection B – Industrial Ethernet
The Ethernet connector is used to connect the receiver to your network or stand alone
computer. An industrial Ethernet connector is optional but might be ideal for dirty
industrial environments because the boot will provide some additional protection.
Tip
If a standalone computer is used a crossover cable is NOT needed. When
connecting the computer to your network, the MAC address is
conveniently located on the top of the unit.
Connection C – N Antenna Connection
The receiver’s N connection is used for the antenna input. The antenna may either be
directly mounted to the receiver or connected with low loss antenna cable. For specific
instructions on locating and mounting a remote antenna, please consult the Echo® System
Installation Manual.
Locating and Installing the Receiver
The receiver must be located near a source of 110-220VAC power and an Ethernet
network connection. The antenna should be located centrally to the area of interest. A
good strategy is to map out your facility and mark possible locations of the receivers.
Based on location and survey testing choose the optimal location. For specific
information on this process, please consult the “Echo® Wireless System Manual”.
The receiver is included with mounting hardware which may be useful for installing it at
your location. The receiver should be physically located where it can be accessed with
the programming cable should settings need to be adjusted.
You may use the short antenna provided with the receiver for testing, setup, and in cases
were the sensors are close to the receiver. To improve the performance, a 6 dBi gain
antenna is recommended and mounted in an elevated location. In some cases a higher
gain antenna, generally not to exceed 8 dBi, can be used. The antenna should be
connected to the receiver using low loss antenna (add spec) cable. For specific
information consult the “Echo® Wireless System Manual”.
Tip
Proper planning and locating the receiver in the best location can cause
drastic performance enhancement. Remember – you will need to access
the box with the programming cable.
Page 6 of 9
Programming the Receiver
The receiver can be programmed to a static or dynamic IP address and one of 12
independent RF frequency bands. Firmware updates can also be installed. The following
equipment is required for programming the receiver:
•
•
•
•
Echo® Wireless Receiver
Power supply
Receiver programming cable
Computer with the Echo® Wireless Data Server software installed
Setting a static or dynamic IP
To check the status of the IP configuration, open the Echo® Wireless Data Server
Software and click the Configure IP address button.
Select the COM port the receiver programming cable is connected to.
Page 7 of 9
To check the current status of the receiver, click the “Query Receiver” button.
To set a Dynamic IP, click the Dynamic IP button and hit Apply Update.
Page 8 of 9
To set a static IP, click the Static IP button and enter the desired IP address, subnet mask,
and default gateway. Hit apply update to program the receiver.
After the receiver has been programmed hit Quit to close the programming menu.
Page 9 of 9

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 9
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : 462d8666-b133-11e0-0000-201bcfe6687c
Producer                        : GPL Ghostscript 8.70
Keywords                        : ()
Modify Date                     : 2011:07:15 07:43:11-04:00
Create Date                     : 2011:07:15 07:43:11-04:00
Creator Tool                    : \376\377\000P\000D\000F\000C\000r\000e\000a\000t\000o\000r\000 \000V\000e\000r\000s\000i\000o\000n\000 \0000\000.\0009\000.\0009
Document ID                     : 462d8666-b133-11e0-0000-201bcfe6687c
Format                          : application/pdf
Title                           : \376\377\000E\000c\000h\000o\000_\000R\000e\000c\000i\000e\000v\000e\000r\000_\000M\000a\000n\000u\000a\000l\000_\0002\0000\0001\0001\000-\0000\0006\000-\0002\0009
Creator                         : \376\377\000d\000c\000o\000r\000e\000l\000l\000i
Description                     : ()
Author                          : dcorelli
Subject                         : 

EXIF Metadata provided by EXIF.tools