PEGATRON BT185 Bluetooth Module User Manual

PEGATRON CORPORATION Bluetooth Module Users Manual

Users Manual

BT-185 Bluetooth ModuleHardware and Driver Reference
BT-185 Hardware & Driver Reference2CONTENTSCONTENTS .................................................................................2INTRODUCTION .........................................................................3SCOPE ............................................................................................. 3ACRONYMS AND DEFINITIONS ..................................................... 3GENERAL FEATURES ..................................................................... 3ANTENNA SPECIFICATION ............................................................ 4REGULATORY REQUIREMENTS ................................................... 4RELIABILITY REQUIREMENTS ...................................................... 4PACKING ......................................................................................... 4DRIVER INSTALLATION ............................................................5DRIVER INSTALLATION STEPS ..................................................... 5DEVICE AND DRIVER DETAILS ...................................................... 7BLUETOOTH CONNECTIONS ........................................................ 8SAFETY STATEMENTS............................................................10NOTE: Information in this document is subject to change after this document is made available.
BT-185 Hardware & Driver Reference 3INTRODUCTIONSCOPEThe purpose of this specication is to document the requirements for Bluetooth 2.1 + EDR, it is USB standard interface for use in laptop. ACRONYMS AND DEFINITIONSAcronym Description GFSK Gaussian Frequency Shift Keying 8DPSK 8 phase Differential Phase Shift Keying π/4 DQPSK pi/4 rotated Differential Quaternary Phase Shift Keying USB Universal Serial Bus or Upper Side Band (depending on context) BER Bit Error Rate. Used to measure the quality of a link dBm Decibels relative to 1mW EDR Enhanced Data Rate GENERAL FEATURES• Network Standard Bluetooth 2.1 + EDR • Chipset BROADCOM BCM2046 • Host interface USB Interface • Out Power Class 2 (max +4dBm) • Data Rate 1, 2, 3Mbps • Modulation GFSK; Pi/4DQPSK(2Mbps); 8DPSK(3Mbps) • Operating Frequency 2402 ~ 2480 MHz • Operating Channel CH1 ~ CH79 • Antenna Connectors PIFA antenna or RF connector • Coverage 1m~10m(depending on environment) • Sensitivity Typical : 90dBm • Driver Support OS Windows 2000, Windows XP and Windows Vista
BT-185 Hardware & Driver Reference4INTRODUCTIONANTENNA SPECIFICATION There are two types of antenna. One is builtin, and the other one is to use conductive connector to connect with the external antenna. The table shown below is the specication of builtin antenna. • Antenna Length 15.74±1.574mm • Operating Freguancy 2.4GHz • Antenna Type Planar invertedF antenna (PIFA) • Polariation Type Linear • Type of Radiation Omnidirectional • Peak Gain Max 2.62 dBi • Impedance 50 Ohm • V.S.W.R. Max 2.0:1 REGULATORY REQUIREMENTS • USA • EU • Taiwan • Canada • JapanRELIABILITY REQUIREMENTS Humidity Test Description Operation Mode: Relative Humidity:20-90% Temperature: 25-50 Duration: 3 days Non-operation Mode: Relative Humidity: 20-90% Temperature: 25-60 Duration: 4 days PACKING The packaging material is customized by customers; the standard packaging contents are: • Bluetooth USB module (x1)• ESD BAG (x1) • Bulk pack carton (500 in 1)
BT-185 Hardware & Driver Reference 5DRIVER INSTALLATIONInstall the device (if not already installed). When entering Windows for the first time, the device should be detected. Select “Don’t show...”Double-click the driver setup file.Select “Install this driver...”.The installation wizard will prepare to install.Click Next to continue.DRIVER INSTALLATION STEPSRead the agreement. Select “I accept...” and click Next.
BT-185 Hardware & Driver Reference6After installing, click Finish to exit.Click Next to install in the default folder or change it. Click Install to continue.Drivers will begin installing.DRIVER INSTALLATION STEPSDRIVER INSTALLATION
BT-185 Hardware & Driver Reference 7DEVICE AND DRIVER DETAILSBefore driver installation, the device may show as “Unknown device” under “Other devices”.After driver installation, the wireless module shows as “Generic Bluetooth Adapter”. Other Windows supporting functions will also be added. DRIVER INSTALLATIONDetailed device info. Detailed driver info.
BT-185 Hardware & Driver Reference8BLUETOOTH CONNECTIONSClick the bluetooth icon on the taskbar to bring up a menu of commands.DRIVER INSTALLATIONSelect “Add a Bluetooth Device”.Select a device. Use a passkey if necessary. The Bluetooth device will be added. Click Finish when done.
BT-185 Hardware & Driver Reference 9BLUETOOTH CONNECTIONSDevices will be categorized into Computers, Phones and modems, etc.You can use a phone or modem device for Internet dial-up connections.
BT-185 Hardware & Driver Reference10SAFETY STATEMENTSFederal Communications Commission StatementThis device complies with FCC Rules Part 15. Operation is subject to the following two conditions:• This device may not cause harmful interference, and• This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.WARNING! The use of a shielded-type power cord is required in order to meet FCC emission limits and to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be used. Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.(Reprinted from the Code of Federal Regulations #47, part 15.193, 1993. Washington DC: Ofce of the Federal Register, National Archives and Records Administration, U.S. Government Printing Ofce.)FCC Radio Frequency Interference RequirementsThis device is restricted to INDOOR USE due to its operation in the 2.402 to 2.480GHz frequency range. FCC requires this product to be used indoors for the frequency range 2.402 to 2.480GHz to reduce the potential for harmful interference to co-channel of the Mobile Satellite Systems. High power radars are allocated as primary user of the 2.402 to 2.480GHz bands. These radar stations can cause interference with and / or damage this device.IMPORTANT: This device and its antenna(s) must not be co-located or op-erating in conjunction with any other antenna or transmitter.
BT-185 Hardware & Driver Reference 11SAFETY STATEMENTSDeclaration of Conformity for R&TTE directive 1999/5/ECProtection requirements for health and safety - Article 3.1a The protection of the health and the safety of the user and any other person, including the objectives with respect to safety requirements contained in Directive 73/23/EEC, but with no voltage limit applying.Protection requirements for electromagnetic compatibility (EMC) - Article 3.1bThe protection requirements with respect to electromagnetic compatibility con-tained in Directive 89/336/EEC.Effective use of the radio spectrum - Article 3.2Radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communication and orbital resources so as to avoid harmful interference.FCC Radio Frequency (RF) Exposure Caution StatementThis equipment complies with FCC RF exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance require-ments, please follow operation instructions in the user’s manual. This equipment is for operation within indoor frequency ranges and is restricted to indoor environ-ments only.FCC Caution: Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. “The manufacturer declares that this device is limited to Channels in the frequency by specied rmware controlled in the USA.”CE Mark WarningThis is a Class B product, in a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.Hereby the [manufacturer’s name], declares that this [product’s name and model number] is in compliance with the essential requirements and other relevant provi-sions of Directive 1999/5/EC.

Navigation menu