PEGATRON CGM4231 DOCSIS3.1 Wireless Residential Gateway with Embedded Digital Voice Adapter User Manual Saf Reg MASTER

PEGATRON CORPORATION DOCSIS3.1 Wireless Residential Gateway with Embedded Digital Voice Adapter Saf Reg MASTER

User Manual

Print Vendor Remove Before Printing Printing Specifications Cable Modem and Residential Gateway Quick Start Product Bulletin – NAM/LATAM 78-4043672-01D0 INLET Page Size: A4 Color process: Black (1/1) double sided Paper weight: 20# Paper type: Opaque Varnish: N/A Number of Pages: 1 page (N/A--signatures) COVER N/A BINDING Fold to A7 size, bar code must be visible for scanning. See fold diagram on next page.
A4 ---> A7Print Vendor Remove Before Printing NOTE: Content of document in this example, except for bar code placement, may not match document to be printed. EnglishFrenchBar code mustbe on outside of folded document!
This illustration is shown as an example to help you locate the MAC address and serial number for your device. If asked, provide the technician or service provider with the serial number and MAC address as listed on the label of your device.T16637DeviceMACAddressProduct Family(Families are Cable Modem, EMTA, Gateway, and Voice Gateway)DeviceSerialNumber1 Turn your PC and other networking devices o and unplug them from power sources.2 CABLE: Connect the RF coaxial cable from the wall outlet to the CABLE connector on the back of the device. (Cable not included.)3 Connect your PC to the back of the device using the connector that best fits your device model and home network needs. Note: Connectors vary by device model. ETHERNET: If your device has more than one Ethernet port, you may connect additional PCs or other networking devices to the extra Ethernet ports. (Cable not included.)Cable Modem and Residential Gateway Quick Start Product BulletinFollow the instructions in this bulletin to connect your cable modem or residential gateway device.Important: Before you connect your device, establish an Internet service account with your preferred Internet service provider. When establishing an account, have your device handy because your Internet service provider may ask you to provide information listed on the device label, such as the device serial number or MAC address.4 TELEPHONE (Optional): If your device supports digital telephone service (VoIP), connect one end of a telephone cable to a telephone outlet in your home or to a telephone or fax machine. Connect the other end of the cable to the first TELEPHONE port on the back of the device. The first port is labeled 1 or 1/2 depending on the device model. (Cable not included.)5 POWER: Connect the barrel end ( ) of the power adapter (included) to the POWER input on the back of the device. Then, plug the adapter into a wall outlet. Optional: If your device has a power switch on the back of the device, make sure that the switch is in the ON position.6 WIRELESSON/OFFWait for the POWER, DS, US, ONLINE, and (if applicable) WIRELESS LEDs on the front panel to stop blinking and remain on continuously. It may take up to 10 minutes for all LEDs to stop blinking. Note: If the device supports wireless and the WIRELESS LED does not turn on, press the WIRELESS ON/OFF button on the front of the device to enable wireless networking. 7 Plug in and power on your PC and other home network devices. The LINK LED on the front of the device turns on or blinks.8 You are ready to surf the internet and use other networked devices. This product may contain “open source” software covered by the GNU General Public License or other open source license agreements: http://www.technicolor.com/en/hi/minisites/open-softwareProblems? If you encounter problems, make sure that all connections are secure. For further assistance, contact your service provider.Fiche de produit pour le démarrage rapide du modem câble et de la passerelle résidentielleSuivez les instructions de cette fiche pour connecter votre modem câble ou votre passerelle.Important: avant de connecter votre périphérique, créez un compte de service Internet auprès de votre fournisseur de service Internet préféré. Lorsque vous créez un compte, gardez votre périphérique à proximité car votre fournisseur de service Internet est susceptible de vous demander des informations figurant sur le périphérique, telles que son numéro de série ou son adresse MAC.Voici un exemple pour vous aider à trouver l'adresse MAC et le numéro de série de votre périphérique. S'il vous le demande, donnez au technicien ou au fournisseur de services le numéro de série ou l'adresse MAC du périphérique.T16637AdresseMACGamme de produits (les gammessont : Cable Modem, EMTA, Gateway et Voice Gateway)Numérode série1 Éteignez votre PC et tous les autres périphériques réseau et débranchez-les de toute source d'alimentation.2 CABLE: connectez le câble coaxial RF de la prise murale au connecteur CABLE à l'arrière du périphérique (câble non fourni.)3 Connectez votre PC à l'arrière du périphérique à l'aide du connecteur le mieux adapté à votre modèle de périphérique et aux besoins de votre réseau domestique. Remarque: les connecteurs varient selon le modèle de périphérique. ETHERNET: si votre périphérique dispose de plusieurs ports Ethernet, vous pouvez connecter d'autres PC ou périphériques réseau aux autres ports Ethernet. (câble non fourni.)4 TELEPHONE (facultatif): si votre périphérique prend en charge le service de téléphone numérique (VoIP), connectez l'extrémité d'un câble téléphonique à une prise téléphonique de votre domicile ou à un téléphone ou fax. Connectez l'autre extrémité du câble téléphonique au port TELEPHONE à l'arrière du périphérique. Le premier port porte le numéro1 ou 1/2 selon le modèle de périphérique. (câble non fourni.)5 POWER: connectez la grosse extrémité ( ) de l'adaptateur secteur (fourni) à l'entrée POWER à l'arrière du périphérique. Connectez ensuite l'adaptateur secteur à une prise murale. Facultatif: si votre périphérique dispose d'un interrupteur sur la face arrière, veillez à ce que l'interrupteur soit en position MARCHE.6 WIRELESSON/OFFAttendez que les voyants POWER, DS, US, ONLINE et (le cas échéant) WIRELESS de la façade cessent de clignoter et restent allumés en continu. Cela peut prendre jusqu'à 10 minutes. Remarque: si le périphérique prend en charge la technologie sans fil et si le voyant WIRELESS ne s'allume pas, appuyez sur le bouton WIRELESS ON/OFF de la façade pour activer le réseau sans fil. 7 Branchez votre PC et les autres périphériques réseau, puis mettez-les sous tension. Le voyant LINK de la façade s'allume ou clignote.8 Vous pouvez à présent surfer sur Internet et utiliser les autres périphériques réseau. Ce produit peut contenir des logiciels «open source» couverts par la Licence Publique Générale GNU ou d'autres contrats de licence open source: http://www.technicolor.com/en/hi/minisites/open-softwareVous rencontrez des problèmes? En cas de problème, vérifiez l'ensemble des connexions. Pour obtenir plus d'assistance, contactez votre fournisseur de services.TECHNICOLOR1-5, rue Jeanne d’Arc92130 Issy-les-MoulineauxFrancewww.technicolor.comCopyright 2016 Technicolor. All rights reserved. All tradenames referenced are service marks, trademarks, or registered trade-marks of their respective companies. Specifications subject to change without notice.DMS3-QIG-25-251 v1.078 -4043672 - 01D 0
Boletín de producto de inicio rápido del cable módem y gateway residencialSiga las instrucciones de este boletín para conectar su cable módem o gateway residencial.Importante: antes de conectar el dispositivo, cree una cuenta de servicio de Internet con su proveedor de servicios de Internet favorito. Al crear una cuenta, tenga a mano el dispositivo porque el proveedor de servicios de Internet puede pedirle que le proporcione la información que aparece en la etiqueta del mismo, como el número de serie o la dirección MAC del dispositivo.Esta ilustración se muestra a modo de ejemplo para ayudarle a localizar la dirección MAC y el número de serie de su dispositivo. En caso de que el técnico o proveedor de servicios le pida el número de serie y la dirección MAC, proporciónele estos datos tal como aparecen en la etiqueta del dispositivo.T16637DirecciónMAC deldispositivoFamilia de productos(las familias son el Cablemódem, EMTA, Gateway y Gateway de voz)Númerode serie deldispositivo1 Apague el PC y otros dispositivos de red, y desenchúfelos de la fuente de alimentación.2 CABLE: conecte el cable coaxial RF de la toma de pared al conector CABLE situado en la parte posterior del dispositivo. (Cable no incluido).3 Conecte el PC en la parte posterior del dispositivo mediante el conector que mejor se adapte a las necesidades de la red doméstica y el modelo de dispositivo. Nota: los conectores pueden variar según el modelo de dispositivo. ETHERNET: si el dispositivo tiene más de un puerto Ethernet, puede conectar más PC u otros dispositivos de red a los puertos Ethernet adicionales. (Cable no incluido).4 TELEPHONE (Opcional): si el dispositivo admite el servicio de telefonía digital (VoIP), conecte uno de los extremos de un cable de acoplamiento telefónico a una toma telefónica de su domicilio, a un teléfono o a un fax. Conecte el otro extremo del cable al primer puerto TELEPHONE en la parte posterior del dispositivo. El primer puerto puede ser 1 o 1/2 en función del modelo de dispositivo. (Cable no incluido).5 POWER: conecte el extremo con forma de barril ( ) del adaptador de alimentación (incluido) a la entrada POWER en la parte posterior del dispositivo. A continuación, enchufe el adaptador en una toma de pared. Opcional: si el dispositivo tiene un interruptor de alimentación en la parte posterior del dispositivo, asegúrese de que el interruptor esté en la posición ON.6 WIRELESSON/OFFEspere a que los LED POWER, DS, US, ONLINE y (en su caso) WIRELESS del panel frontal dejen de parpadear y permanezcan siempre encendidos. Deberá esperar un máximo de 10 minutos para que todos los LED dejen de parpadear. Nota: si el dispositivo admite la conexión inalámbrica y el LED WIRELESS no se enciende, pulse el botón WIRELESS ON/OFF en la parte frontal del dispositivo para habilitar la red inalámbrica. 7 Enchufe y encienda su PC y demás dispositivos de la red doméstica. El LED LINK en la parte frontal del dispositivo se encenderá o parpadeará.8 Ya está listo para navegar por Internet y utilizar otros dispositivos de red. Este producto puede contener software “de código abierto” cubierto por la Licencia Pública General de GNU u otros acuerdos de licencia de código abierto: http://www.technicolor.com/en/hi/minisites/open-softwareQué hacer en caso de problemas Si tiene problemas, asegúrese de que todas las conexiones estén conectadas correctamente. Si necesita más ayuda, póngase en contacto con su proveedor de servicios.Boletim de produtos de início rápido para modem de cabo e gateway residencialSiga as instruções incluídas neste boletim para ligar o seu modem de cabo ou dispositivo de gateway residencial.Importante: antes de fazer a ligação do dispositivo, crie uma conta de serviços de Internet junto de um fornecedor de serviços de Internet à sua escolha. Mantenha o dispositivo à mão quando criar uma conta, uma vez que o fornecedor de serviços de Internet poderá pedir-lhe que disponibilize as informações indicadas na etiqueta do dispositivo, tais como o número de série ou o endereço MAC.Esta imagem é apresentada como um exemplo, para o ajudar a localizar o endereço MAC e o número de série do dispositivo. Se tal lhe for solicitado, transmita ao técnico ou fornecedor de serviços o número de série e o endereço MAC indicados na etiqueta do dispositivo.T16637EndereçoMAC dodispositivoFamília de produtos(as famílias são: modem de cabo, EMTA, gateway e gateway de voz)Número de série dodispositivo1 Desligue o computador e outros dispositivos de rede, e remova as fichas das fontes de alimentação.2 CABLE: ligue o cabo coaxial RF desde a tomada de parede até ao conector CABLE na parte de trás do dispositivo. (Cabo não incluído.)3 Ligue o computador à parte de trás do dispositivo utilizando o conector mais adequado ao modelo do dispositivo e às suas necessidades de rede doméstica. Nota: os conectores variam consoante o modelo do dispositivo. ETHERNET: se o dispositivo tiver mais de uma porta Ethernet, pode ligar mais computadores ou outros dispositivos de rede às portas Ethernet adicionais. (Cabo não incluído.)4 TELEPHONE (Opcional): se o dispositivo suportar o serviço telefónico digital (VoIP), ligue uma extremidade de um cabo telefónico a uma tomada telefónica em sua casa ou a um telefone ou aparelho de fax. Ligue a outra extremidade do cabo à primeira porta TELEPHONE na parte de trás do dispositivo. A primeira porta encontra-se identificada como 1 ou 1/2, consoante o modelo do dispositivo. (Cabo não incluído.)5 POWER: ligue a extremidade cilíndrica ( ) do transformador (incluído) à entrada POWER na parte de trás do dispositivo. Em seguida, ligue o transformador a uma tomada de parede. Opcional: se o dispositivo tiver um interruptor de alimentação na parte de trás, certifique-se de que o interruptor está na posição ON.6 WIRELESSON/OFFAguarde até os indicadores LED POWER, DS, US, ONLINE e (se aplicável) WIRELESS no painel frontal pararem de piscar e permanecerem acesos continuamente. Os indicadores LED poderão demorar até 10 minutos a pararem de piscar. Nota: se o dispositivo for compatível com rede sem fios e se o LED WIRELESS não se acender, prima o botão WIRELESS ON/OFF na parte da frente do dispositivo para possibilitar a ligação através de rede sem fios. 7 Ligue a ficha do computador à tomada e, em seguida, ligue o computador e outros dispositivos da rede doméstica. O LED LINK na parte da frente do dispositivo acende-se ou pisca.8 Pode agora navegar na Internet e utilizar outros dispositivos ligados em rede. Este produto poderá conter software de “fonte aberta” abrangido pela GNU General Public License (Licença Pública Geral GNU) ou outros acordos de licenciamento de fonte aberta: http://www.technicolor.com/en/hi/minisites/open-softwareProblemas? Se tiver algum problema, certifique-se de que todas as ligações estão bem feitas. Para obter assistência adicional, contacte o fornecedor de serviços.
Software described in this document is protected by copyright law and furnished to you under a license agreement. You may only use or copy this software in accordance with the terms of your license agreement.Open Source Software notificationThe software of this product may contain certain open source software modules which are subject to Open Source Software license terms (see https://opensource.org/osd for definition). Such Open Source Software components and/or versions may change in the future versions of the software product.A list of the Open Source Software used or provided as embedded into the current software of the product and their corresponding licenses and version number are, to the extent required by applicable terms, available on Technicolor's website at the following address: www.technicolor.com/en/hi/minisites/open-software or at another address as Technicolor may provide from time to time.If and where applicable, depending on the terms of the applicable Open Source Software licenses, the source code of the Open Source Software is available for free upon request.For avoidance of doubt, Open Source Software is only licensed by the original owner of the Open Source Software under the terms set forth in the designated Open Source License.Environmental informationBatteries (if applicable)Batteries contain hazardous substances which pollute the environment. Do not dispose of them with other articles. Take care to dispose them at special collecting points.Recycle or dispose of batteries in accordance with the battery manufacturer’s instructions and local/national disposal and recycling regulations.Energy efficiencyEnergy savingsThe user documentation that is included with your product not only provides useful information on all the features of your product, but also on its energy consumption. We strongly encourage you to carefully read this documentation before putting your equipment in service in order to get the best service it can offer you.Safety instructionsClimatic conditionsThis product:• Is intended for in-house stationary use; the maximum ambient temperature must not exceed 40 °C (104 °F); the relative humidity must be between 20 and 80 %.• Must not be mounted in a location exposed to direct or excessive solar and/or heat radiation.• Must not be exposed to heat trap conditions and must not be subjected to water or condensation.• Must be installed in a Pollution Degree 2 environment (an environment where there is no pollution or only dry, non-conductive pollution).If applicable, batteries (battery pack or batteries installed) must not be exposed to excessive heat such as sunshine, fire or the like.Ventilation and positioningThis product is intended to be used indoors in a residential or office environment.• Remove all packaging material before applying power to the product.• Place and use the product only in positions as described in the user documentation that is included with your product.• Do not block or cover any ventilation openings; never stand it on soft furnishings or carpets.• Never push objects through the openings in this product.• Leave 7 to 10 cm (3 to 4 inches) around the product to ensure that proper ventilation gets to it.• Do not install the product near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.• Do not put anything on it which might spill or drip into it (for example, lighted candles or containers of liquids). Do not expose it to dripping or splashing, rain or moisture. If a liquid enters inside the product, or if the product has been exposed to rain or moisture, unplug it immediately and contact your supplier or customer service.CleaningUnplug this product from the wall socket and disconnect from all other devices before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.!• Read these instructions.• Keep these instructions.• Heed all warnings and cautions.• Follow all instructions.For APPROVAL and NOT for distribution outside Technicolor!!!
Water and moistureDo not use this product near water, for example near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement or near a swimming pool. Transition of the product from a cold environment to a warm one may cause condensation on some of its internal parts. Allow it to dry by itself before using the product.Electrical poweringThe powering of the product must adhere to the power specifications indicated on the marking labels.In case this product is powered by a power supply unit:•For US and Canada: This product is intended to be supplied by a UL listed Direct Plug-inPower Unit marked "Class 2" and rated as indicated on the label on your product.• This power supply unit must be Class II and a Limited Power Source in accordance with the requirements of IEC 60950-1/ EN 60950-1, Clause 2.5 and rated as indicated on the label on your product. It must be tested and approved to national, or local standards.AccessibilityThe plug on the power supply cord or power supply unit serves as disconnect device. Be sure that the mains supply socket outlet you use is easily accessible and located as close to the product as possible.The power connections to the product and the mains supply socket outlet socket must be accessible at all times, so that you always can disconnect the product quickly and safely from the mains supply.OverloadingDo not overload mains supply socket outlets and extension power cords as this increases the risk of fire or electric shock.Handling batteriesThis product may contain disposable batteries.• Insert batteries correctly. There may be a risk of explosion if the batteries are incorrectly inserted.• Do not attempt to recharge disposabal or non-reusable batteries.• Please follow instructions provided for charging rechargeable batteries.• Replace batteries with the same or equivalent type.• Do not expose batteries to excessive heat (such as sunlight or fire) and to temperatures above 100 °C (212 °F).Cable DistributionFor this apparatus, the cable shield/screen shall be grounded (earthed) as close as practical to the point of entry of the cable into the building.For products sold in the US and Canada, this reminder is provided to call the system installer's attention to ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable (or Canadian Electrical Code Part 1).Limiting the human body exposure to electromagnetic fieldsThis product should be installed and operated with a minimum distance of 20 cm (8 inches) between the product and a person’s body.ServicingIf service or repair work is required, take it to a qualified service dealer.Damage requiring serviceUnplug this product from the mains supply socket outlet and refer servicing to qualified service personnel under the following conditions:• When the power supply, power cord or its plug are damaged.• When the attached cords are damaged or frayed.!Only use the power supply unit that is supplied with this product, is supplied by your service provider or local product supplier, or a replacement power supply unit provided by your service provider or local product supplier.The use of other types of power supplies is prohibited.If you are not sure of the type of power supply needed, consult the user documentation that is included with your product or contact your service provider or local product supplier.!CAUTIONThere is danger of explosion if the battery is mishandled or incorrectly replaced. Replace only with the same or equivalent type of battery. Do not disassemble it or attempt to recharge it outside the system.Do not disassemble, crush, puncture, short the external contacts, dispose of in fire, or expose to fire, water or other liquids.!To reduce the risk of electric shock or electrocution, do not disassemble this product.For APPROVAL and NOT for distribution outside Technicolor!!!
• If liquid has been spilled into the product.• If the product has been exposed to rain or water.• If the product does not operate normally.• If the product has been dropped or damaged in any way.• There are noticeable signs of overheating.• If the product exhibits a distinct change in performance.• If the product is giving off smoke or a burning smell.Protect the product when moving itAlways disconnect the power source when moving the product or connecting or disconnecting cables.Interface classifications (upon applicability)The external interfaces of the product are classified as follows:• Cable (IN/OUT): TNV circuit, not subjected to overvoltages (TNV-1)• Phone, FXS: TNV (Telecommunications Network Voltage ) circuit, not subjected to overvoltages (TNV-2)• MoCA, HPNA, RF: TNV circuit, not subjected to overvoltages (TNV-1)• All other interface ports (e.g. Ethernet, USB,...), including the low voltage power input from the AC mains power supply: SELV (Safety Extra-Low Voltage) circuits.Regulatory informationNorth-America - CanadaNotification of Canadian Radio Frequency interference statementThis Class B digital apparatus complies with Canadian ICES-003.This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.Canada - Radiation exposure statementThis equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm (8 inches) between the radiator and your body.Canada - Industry Canada (IC)In case this product is equipped with a wireless transceiver, this device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.Restricted frequency bandsIn case this product is equipped with a wireless transceiver operating in the 2.4 GHz band, it may only use channels 1 to 11 (2412 to 2462 MHz) on Canada territory.In case this product is equipped with a wireless transceiver operating in the 5 GHz band, it is for indoor use only.The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.North-America - United States of AmericaImportant safety instructions• The cable distribution system should be grounded (earthed) in accordance with ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820,93, Grounding of outer Conductive Shield of a Coaxial Cable.• Leave 5 to 8 cm (2 to 3 inches) around the product to ensure proper ventilation to it.• Never push objects through the openings in this product.Federal Communications Commission (FCC) radio frequency interference statementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. For APPROVAL and NOT for distribution outside Technicolor!!!
• Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.Responsible Party: Technicolor, 101W. 103rd St., Indianapolis, IN 46290 USA, 317-587-5466.RF exposure statementThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in the product documentation.When the product is equipped with a wireless interface, then it becomes a mobile or fixed mounted modular transmitter and must have a separation distance of at least 20 cm (8 inches) between the antenna and the body of the user or nearby persons. In practice, this means that the user or nearby persons must have a distance of at least 20 cm (8 inches) from the product and must not lean on the product in case it is wall-mounted.With a separation distance of 20 cm (8 inches) or more, the M(aximum) P(ermissible) E(xposure) limits are well above the potential this wireless interface is capable to produce.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Restricted frequency bandsIn case this product is equipped with a wireless transceiver operating in the 2.4 GHz band, it can only use channels 1 to 11 (2412 to 2462 MHz) on U.S.A. territory.In case this product is equipped with a wireless transceiver operating in the 5 GHz band, it meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.For APPROVAL and NOT for distribution outside Technicolor!!!
TECHNICOLOR1-5 rue Jeanne d’Arc92130 Issy-les-MoulineauxFrancewww.technicolor.com*37743260*37743260Copyright 2017 Technicolor. All rights reserved. All tradenames referenced are service marks, trademarks, or registered trademarks of their respective companies. Specifications subject to change without notice.DMS3-SAF-25-465 v1.0. SAFETY INSTRUCTIONS AND REGULATORY NOTICESBEFORE YOU START INSTALLATION OR USE OF THIS PRODUCT, CAREFULLY READ ALL SAFETY INSTRUCTIONSApplicabilityThese Safety Instructions and Regulatory Notices apply to:• Technicolor Cable Modems & GatewaysUsing equipment safelyUsed symbolsFollowing symbols may be found in this and accompanying documentation as well as on the product or accompanying accessories:DirectivesProduct useYou must install and use this product in strict accordance with the manufacturer's instructions as described in the user documentation that is included with your product.Before you start installation or use of this product, carefully read the contents of this document for device specific constraints or rules that may apply in the country where you want to use this product.If you have any doubts about the installation, operation or safety of this product, please contact your supplier.Any change or modification made to this product that is not expressly approved by Technicolor will result in the loss of product warranty and may void the user's authority to operate this equipment. Technicolor disclaims all responsibility in the event of use that does not comply with the present instructions.Software and firmware useThe firmware in this equipment is protected by copyright law. You may only use the firmware in the equipment in which it is provided. Any reproduction or distribution of this firmware, or any portion of it, without express written consent from Technicolor is prohibited.!When using this product, always follow the basic safety precautions to reduce the risk of fire, electric shock and injury to persons, including the following:• Always install the product as described in the documentation that is included with your product.• Do not use this product to report a gas leak in the vicinity of the leak.• Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.Symbol IndicationThis symbol is intended to alert you that uninsulated voltage within this product may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this product.This symbol is intended to alert you of the presence of important operating and maintenance (servicing) instructions in the documentation that is included with your product.This symbol indicates for indoor use only (IEC 60417-5957).!This symbol indicates Double insulated Class II equipment (IEC 60417-5172). Does not require an earth connection.This symbol indicates Alternating Current (AC).This symbol indicates Direct Current (DC).This symbol indicates Electrical polarity.This symbol indicates Fuse.Symbol IndicationFor APPROVAL and NOT for distribution outside Technicolor!!!
Software described in this document is protected by copyright law and furnished to you under a license agreement. You may only use or copy this software in accordance with the terms of your license agreement.Open Source Software notificationThe software of this product may contain certain open source software modules which are subject to Open Source Software license terms (see https://opensource.org/osd for definition). Such Open Source Software components and/or versions may change in the future versions of the software product.A list of the Open Source Software used or provided as embedded into the current software of the product and their corresponding licenses and version number are, to the extent required by applicable terms, available on Technicolor's website at the following address: www.technicolor.com/en/hi/minisites/open-software or at another address as Technicolor may provide from time to time.If and where applicable, depending on the terms of the applicable Open Source Software licenses, the source code of the Open Source Software is available for free upon request.For avoidance of doubt, Open Source Software is only licensed by the original owner of the Open Source Software under the terms set forth in the designated Open Source License.Environmental informationBatteries (if applicable)Batteries contain hazardous substances which pollute the environment. Do not dispose of them with other articles. Take care to dispose them at special collecting points.Recycle or dispose of batteries in accordance with the battery manufacturer’s instructions and local/national disposal and recycling regulations.Energy efficiencyEnergy savingsThe user documentation that is included with your product not only provides useful information on all the features of your product, but also on its energy consumption. We strongly encourage you to carefully read this documentation before putting your equipment in service in order to get the best service it can offer you.Safety instructionsClimatic conditionsThis product:• Is intended for in-house stationary use; the maximum ambient temperature must not exceed 40 °C (104 °F); the relative humidity must be between 20 and 80 %.• Must not be mounted in a location exposed to direct or excessive solar and/or heat radiation.• Must not be exposed to heat trap conditions and must not be subjected to water or condensation.• Must be installed in a Pollution Degree 2 environment (an environment where there is no pollution or only dry, non-conductive pollution).If applicable, batteries (battery pack or batteries installed) must not be exposed to excessive heat such as sunshine, fire or the like.Ventilation and positioningThis product is intended to be used indoors in a residential or office environment.• Remove all packaging material before applying power to the product.• Place and use the product only in positions as described in the user documentation that is included with your product.• Do not block or cover any ventilation openings; never stand it on soft furnishings or carpets.• Never push objects through the openings in this product.• Leave 7 to 10 cm (3 to 4 inches) around the product to ensure that proper ventilation gets to it.• Do not install the product near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.• Do not put anything on it which might spill or drip into it (for example, lighted candles or containers of liquids). Do not expose it to dripping or splashing, rain or moisture. If a liquid enters inside the product, or if the product has been exposed to rain or moisture, unplug it immediately and contact your supplier or customer service.CleaningUnplug this product from the wall socket and disconnect from all other devices before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.!• Read these instructions.• Keep these instructions.• Heed all warnings and cautions.• Follow all instructions.For APPROVAL and NOT for distribution outside Technicolor!!!
Water and moistureDo not use this product near water, for example near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement or near a swimming pool. Transition of the product from a cold environment to a warm one may cause condensation on some of its internal parts. Allow it to dry by itself before using the product.Electrical poweringThe powering of the product must adhere to the power specifications indicated on the marking labels.In case this product is powered by a power supply unit:•For US and Canada: This product is intended to be supplied by a UL listed Direct Plug-inPower Unit marked "Class 2" and rated as indicated on the label on your product.• This power supply unit must be Class II and a Limited Power Source in accordance with the requirements of IEC 60950-1/ EN 60950-1, Clause 2.5 and rated as indicated on the label on your product. It must be tested and approved to national, or local standards.AccessibilityThe plug on the power supply cord or power supply unit serves as disconnect device. Be sure that the mains supply socket outlet you use is easily accessible and located as close to the product as possible.The power connections to the product and the mains supply socket outlet socket must be accessible at all times, so that you always can disconnect the product quickly and safely from the mains supply.OverloadingDo not overload mains supply socket outlets and extension power cords as this increases the risk of fire or electric shock.Handling batteriesThis product may contain disposable batteries.• Insert batteries correctly. There may be a risk of explosion if the batteries are incorrectly inserted.• Do not attempt to recharge disposabal or non-reusable batteries.• Please follow instructions provided for charging rechargeable batteries.• Replace batteries with the same or equivalent type.• Do not expose batteries to excessive heat (such as sunlight or fire) and to temperatures above 100 °C (212 °F).Cable DistributionFor this apparatus, the cable shield/screen shall be grounded (earthed) as close as practical to the point of entry of the cable into the building.For products sold in the US and Canada, this reminder is provided to call the system installer's attention to ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable (or Canadian Electrical Code Part 1).Limiting the human body exposure to electromagnetic fieldsThis product should be installed and operated with a minimum distance of 30 cm between the product and a person’s body.ServicingIf service or repair work is required, take it to a qualified service dealer.Damage requiring serviceUnplug this product from the mains supply socket outlet and refer servicing to qualified service personnel under the following conditions:• When the power supply, power cord or its plug are damaged.• When the attached cords are damaged or frayed.!Only use the power supply unit that is supplied with this product, is supplied by your service provider or local product supplier, or a replacement power supply unit provided by your service provider or local product supplier.The use of other types of power supplies is prohibited.If you are not sure of the type of power supply needed, consult the user documentation that is included with your product or contact your service provider or local product supplier.!CAUTIONThere is danger of explosion if the battery is mishandled or incorrectly replaced. Replace only with the same or equivalent type of battery. Do not disassemble it or attempt to recharge it outside the system.Do not disassemble, crush, puncture, short the external contacts, dispose of in fire, or expose to fire, water or other liquids.!To reduce the risk of electric shock or electrocution, do not disassemble this product.
• If liquid has been spilled into the product.• If the product has been exposed to rain or water.• If the product does not operate normally.• If the product has been dropped or damaged in any way.• There are noticeable signs of overheating.• If the product exhibits a distinct change in performance.• If the product is giving off smoke or a burning smell.Protect the product when moving itAlways disconnect the power source when moving the product or connecting or disconnecting cables.Interface classifications (upon applicability)The external interfaces of the product are classified as follows:• Cable (IN/OUT): TNV circuit, not subjected to overvoltages (TNV-1)• Phone, FXS: TNV (Telecommunications Network Voltage ) circuit, not subjected to overvoltages (TNV-2)• MoCA, HPNA, RF: TNV circuit, not subjected to overvoltages (TNV-1)• All other interface ports (e.g. Ethernet, USB,...), including the low voltage power input from the AC mains power supply: SELV (Safety Extra-Low Voltage) circuits.Regulatory informationNorth-America - CanadaNotification of Canadian Radio Frequency interference statementThis Class B digital apparatus complies with Canadian ICES-003.This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.Canada - Radiation exposure statementThis equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 35cm between the radiator and your body.Canada - Industry Canada (IC)In case this product is equipped with a wireless transceiver, this device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.Restricted frequency bandsIn case this product is equipped with a wireless transceiver operating in the 2.4 GHz band, it may only use channels 1 to 11 (2412 to 2462 MHz) on Canada territory.In case this product is equipped with a wireless transceiver operating in the 5 GHz band, it is for indoor use only.The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.North-America - United States of AmericaImportant safety instructions• The cable distribution system should be grounded (earthed) in accordance with ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820,93, Grounding of outer Conductive Shield of a Coaxial Cable.• Leave 5 to 8 cm (2 to 3 inches) around the product to ensure proper ventilation to it.• Never push objects through the openings in this product.Federal Communications Commission (FCC) radio frequency interference statementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.Responsible Party: Technicolor, 101W. 103rd St., Indianapolis, IN 46290 USA, 317-587-5466.RF exposure statementThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in the product documentation.When the product is equipped with a wireless interface, then it becomes a mobile or fixed mounted modular transmitter and must have a separation distance of at least 30 cm between the antenna and the body of the user or nearby persons. In practice, this means that the user or nearby persons must have a distance of at least 30 cm from the product and must not lean on the product in case it is wall-mounted.With a separation distance of 30 cm or more, the M(aximum) P(ermissible) E(xposure) limits are well above the potential this wireless interface is capable to produce.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Restricted frequency bandsIn case this product is equipped with a wireless transceiver operating in the 2.4 GHz band, it can only use channels 1 to 11 (2412 to 2462 MHz) on U.S.A. territory.In case this product is equipped with a wireless transceiver operating in the 5 GHz band, it meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu