Contents
- 1. user manual
- 2. Users manual
- 3. User Manual
user manual
Manual
Unihan UPWL6580
Federal Communications Commission Statement
This device complies with FCC Rules Part 15. Operation is subject to the following
i. This device may not cause harmful interference, and
ii. This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a class B digital device,
pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
i. Reorient or relocate the receiving antenna.
ii. Increase the separation between the equipment and receiver.
iii. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
iv. Consult the dealer or an experienced radio/TV technician for help.
CAUTION! You are cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
Reprinted from the Code of Federal Regulations #47, part 15.193, 1993. Washington DC: Office of the
Federal Register, National Archives and Records Administration, U.S. Government Printing Office.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of the device.
This radio transmitter (identify the device by certification number, or model number if Category II) has
been approved by Industry Canada to operate with the antenna types listed below with the maximum
permissible gain and required antenna impedance for each antenna type indicated. Antenna types not
included in this list, having a gain greater than the maximum gain indicated for that type, are strictly
prohibited for use with this device.
No. Ant. Cat. Ant. Type Brand Part No. G
A
NT
(
dBi
)
1 Integral PCB Wanshih UC3WFI0057 1.99
2 Integral PCB Wanshih UC3WFI0058 2.08
3 Integral PCB Wanshih UC3WFI0090 2.03
4 Integral PCB Airgain N5X20B (6.5cm) 1.70
5 Integral PCB Airgain N5X20B (10cm) 1.70
6 Integral PCB Airgain N5X20SC 1.90
Safety statements
Regulatory Information/Disclaimers
Installation and use of this device must be in strict accordance with the instructions included in the user
documentation provided with the product. Any changes or modifications (including the antennas) made
to this device that are not expressly approved by the manufacturer may void the user’s authority to
operate the equipment. The manufacturer is not responsible for any radio or television interference
caused by unauthorized modification of this device, or the substitution of the connecting cables and
equipment other than manufacturer specified. It is the responsibility of the user to correct any
interference caused by such unauthorized modification, substitution or attachment. Manufacturer and
its authorized resellers or distributors will assume no liability for any damage or violation of government
regulations arising from failing to comply with these guidelines.
CAUTION! To maintain compliance with FCC’s RF exposure guidelines, this equipment should be
installed and operated with minimum distance [20cm] between the radiator and your body. Use on the
supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter
and may violate FCC regulations.
Safety Information
In order to maintain compliance with the FCC RF exposure guidelines, this equipment should be
installed and operated with minimum distance [20cm] between the radiator and your body. Use only
with supplied antenna.
Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC
regulations.
CAUTION! Any changes or modifications not expressly approved in this manual could void your
authorization to use this device.
Any changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate this equipment.
MPE Statement
Your device contains a low power transmitter. When device is transmitted it sends out Radio Frequency
(RF) signal.
FCC Radio Frequency Exposure
This device has been evaluated under FCC Bulletin OET 65C and found compliant to the requirements as
set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247(b)(4) addressing RF Exposure from radio
frequency devices. The radiation output power of this device is far below the FCC radio frequency
exposure limits. Nevertheless, this device shall be used in such a manner that the potential for human
contact during normal operation – as a mobile or portable device but use in a body-worn way is strictly
prohibit. When using this device, a certain separation distance between antenna and nearby persons
has to be kept to ensure RF exposure compliance. In order to comply with the RF exposure limits
established in the ANSI C95.1 standards, the distance between the antennas and the user should not be
less than [20cm].
RF Exposure
The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
The final end product must be labeled in a visible area with the following " Contains TX FCC ID:
VUIUPWL6580".
This transmitter module is authorized only for use in device where the antenna may be installed such
that 20 cm may be maintained between the antenna and users. The final end product must be labeled
in a visible area with the following: “Contains transmitter module IC: 7582A-UPWL6580”.
Frequency Statement
This device is restricted to indoor use when operated in the 5.15 to 5.25 GHz frequency range.
The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful
interference to co-channel mobile satellite systems
About this guide
This user guide contains the information your PEGATRON WIFI Module.
System requirements
Before installing the PEGATRON WIFI module, make sure that your system meets the
following requirements:
Intel® Pentium® 4 or AMD K7/K8 system
Minimum 64MB system memory
Windows® XP/VISTA operating system
Installing the device drivers
To install the device driver in your computer:
Insert the support CD to the optical drive and follow the following procedure.
Step 1:Browser my computer for driver software
Step 2
Step 3:click Browse,then select the win7 folder,then click OK and Next
Step 4: click Install
Step 5: the driver shows below
Step 6: click Close