PEGATRON WAP571E Wireless-AC/N Premium Dual Radio Outdoor Access Point User Manual QSG 571E EN

PEGATRON CORPORATION Wireless-AC/N Premium Dual Radio Outdoor Access Point QSG 571E EN

User Manual.rev

Quick Start GuideCisco WAP571E Wireless-AC/N Premium Dual Radio Outdoor Access Point
1 Cisco WAP571E Wireless Access PointWelcomeThank you for choosing the Cisco WAP571E Wireless-AC/N Premium Dual Radio Outdoor Access Point. The Cisco WAP571E is an outdoor dual radio 802.11ac + 802.11n access point.This guide is designed to familiarize you with the general layout of the access point, describe how to deploy the device in your network, and describe how to configure the device. Your access point has more features and functionality than what is described in this guide. For additional information, see the Administration Guide. A link to the Administration Guide is found in Where to Go From Here.Package Contents•Wireless Access Point•Mounting kit•This Quick Start Guide•Ethernet cable•Pointer Card with China RoHS•Technical Support Contacts•EU Directives 1999/5/EC Compliance Information (for EU SKU only)Before You BeginBefore you begin the installation, make sure that you have the following equipment and services: •A computer with browser support for:– Internet Explorer v7.0 or later– Chrome v5.0 or later– Firefox v3.0 or later–Safari v3.0 or later•Tools for installing the hardware•One or more Ethernet network switches with PoE1
Cisco WAP571E Wireless Access Point 2Cisco WAP571E Wireless-AC/N Premium Dual Radio Outdoor Access Point FeaturesFront PanelThe front panel of the device consists of a single system LED. For a full description of the colors of the light and its indications, see Verifying the Hardware Installation.A Kensington lock slot is found under the lights.Back PanelThe back panel of the device has a water proof RJ-45 Ethernet port and reset bottom. Facing the side of the device, the right port (labeled "ETH0/PD") is an 802.3at and 802.3af Power over Ethernet (PoE) port which is used to power your device. The left port (labeled "ETH1") is a general Gigabit Ethernet LAN interface. Both are auto-sensing, Gigabit Ethernet (802.3) ports used to connect your WAP devices to network devices, such as computers, routers, or switches. We strongly recommend that you use a Category 5e or better cable for Gigabit connectivity.Side PanelThe side panel of the device has a Reset button at right. See Rebooting the Devices or Returning them to their Factory Default Settings for information on the Reset button.Default Setting If you are using a Cisco RV Series router, the default range for the DHCP assigned address is from 192.168.1.100 to 192.168.1.254. Any device connecting to the same LAN will be assigned an IP address in this range.If your network does not have an existing DHCP server, the WAP571E will start a DHCP server for WLAN stations and stop the DHCP client when WAP571E is in factory default. The DHCP server will assign the IP address from 192.168.1.20 to 192.168.1.100.Parameter Default ValueUsername ciscoPassword ciscoLAN IP Address DHCP address assigned by serverFallback LAN IP 192.168.1.245Subnetwork Mask 255.255.255.02
3 Cisco WAP571E Wireless Access PointMounting the Cisco WAP571E Wireless-AC/N Premium Dual Radio Outdoor Access PointYou can place your access point at an outdoor location and mount it on a wall or pole.Placement Tips• Ambient Temperature—To prevent the access point from overheating, do not operate it in an area that exceeds an ambient temperature of 122°F (55°C).• Mechanical Loading—The device should be level, stable, and secure to prevent it from sliding or shifting out of position.Wall and Pole MountingThe Cisco WAP571E device can be wall or pole-mounted. A mounting kit is packaged with your device. The kit is designed to install your device to the wall or a pole. The outdoor model includes an adjustable bracket to mount on a flat vertical surface. Adjustments can be made in up/down, left/right direction for signal optimization. Pole-mount allows for mounting to small pole (3" diameter max) and is also adjustable.3
Cisco WAP571E Wireless Access Point 4WARNING Insecure mounting might damage the device or cause injury. Cisco is not responsible for damages incurred by insecure wall or pole mounting.Pole-mounting: To mount the Cisco WAP 571E device on a pole:STEP 1Fix Holder_1 and GND wire on WAP571E by 4 M6*10 screws and screw washers. GND wire can provide better ESD protection.STEP 2Fix Holder_2 and Holder_3 on Pole by 4 M6*130 screws and screw washers. STEP 3Fix WAP571E and Holder_1 to Holder_2 by 4 M6*10 Screws and screw washers.
5 Cisco WAP571E Wireless Access PointWall-mounting: To mount the Cisco WAP 571E device on a wall:STEP 1Fix Holder_1 and GND wire on WAP571E by 4 M6*10 screws and screw washers. GNDwirecanprovidebetterESDprotection.STEP 2Fix HOLDER_3 on wall by 4 anchors.
Cisco WAP571E Wireless Access Point 6STEP 3Fix Holder_2 and Holder_3 by 4 M6*10 screws and screw washers.STEP 4Fix WAP571E and Holder_1 to Holder_2 by 4 M6*10 Screws and screw washers.
7 Cisco WAP571E Wireless Access Point
Cisco WAP571E Wireless Access Point 8Connecting the Cisco WAP571E Wireless-AC/N Premium Dual Radio Outdoor Access PointYou can perform the initial configuration using either a wired or wireless connection. The default configuration of the WAP 571 has the Wi-Fi radio turned on.To connect the WAP 571E to the wired network:STEP 1Connect the Ethernet cable to the Ethernet port of a PoE switch. STEP 2Connect the other end of the network Ethernet cable to the Ethernet port (PoE) of the wireless access point. NOTE WAP571E bundles the two Ethernet ports to be link aggregation mode. If the two Ethernet ports have been connected at the same time, the link partner must also support link aggregation.This wireless default configuration will not allow traffic between WiFi and Ethernet; users will need to go through the setup wizard to resume the traffic between WiFi and Ethernet.To connect the WAP 571E to the network wirelessly:STEP 1Use wireless clients to locate the WAP571E’s SSID (CiscoSB-Setup). STEP 2Use the ‘cisco123’ passkey to access the access point.NOTE The system provides a one-time-only access to configure the access point using a wireless connection.After installation, all lights should be active. Refer to Verifying the Hardware Installation for details about the different lights on the WAP 571E. 4
9 Cisco WAP571E Wireless Access PointVerifying the Hardware InstallationTo verify the hardware installation, complete the following tasks:•Check the cable connections.•Check the state of the indicator lights.NOTE If you need help resolving a problem, visit the Cisco Support Community at www.cisco.com/go/smallbizsupport. Label Activity DescriptionPower Off The WAP571E is out of power.Solid (Green) The Cisco WAP571E is normal; no wireless client connected.Solid (Blue) The Cisco WAP571E is normal; at least one wireless client connected.Flashing (Blue) The Cisco WAP571E is upgrading the firmware.Solid (Red) The Cisco WAP571E fails to boot with bothfirmware images.5
Cisco WAP571E Wireless Access Point 10Getting Started with the ConfigurationTo configure the wireless access points, you can either use Ethernet or wireless. Please follow these steps to access the Wizard and then the web-based configuration utility from your computer by Ethernet:STEP 1Ethernet: Connect the wireless access point to the same network (IP subnet) as your computer. The factory default IP address configuration of the access points is DHCP. Make sure your DHCP server is running and can be reached.See Incorrect IP Address for troubleshooting information, or if you do not have a DHCP server. Wireless: Search the wireless SSID "CiscoSB-Setup", and connect to this SSID with the passphrase "cisco123".STEP 2Locate the IP address of the wireless access point.a. The wireless access points can be accessed and managed by Cisco network tools and services including the Cisco FindIT Network Discovery Utility that enables you to automatically discover all supported Cisco devices in the same local network segment as your computer. You can get a snapshot view of each device or launch the product configuration utility to view and configure the settings. For more information, see www.cisco.com/go/findit.b. The wireless access points are Bonjour-enabled and automatically broadcast their services and listen for services being advertised by other Bonjour-enabled devices. If you have a Bonjour-enabled browser, such as Microsoft Internet Explorer with a Bonjour plug-in, or the Apple Mac Safari browser, you can find the wireless access point on your local network without knowing its IP address.You can download the complete Bonjour for Microsoft Internet Explorer browser from Apple’s website by visiting: http://www.apple.com/bonjour/ c. Locate the IP address assigned by your DHCP server by accessing your router or DHCP server. See your DHCP server instructions for more information. STEP 3Launch a web browser, such as Microsoft Internet Explorer or Mozilla Firefox.STEP 4In the Address field, enter the default DHCP address and press the Enter key.6
">
11 Cisco WAP571E Wireless Access PointSTEP 5Enter the default user name of cisco and password of cisco in the User Name and Password fields.STEP 6Click Login. The Wireless Access Point Setup Wizard appears.STEP 7Follow the Setup Wizard instructions to finish the WAP device installation. We strongly recommend that you use the Setup Wizard for the first installation. The Setup Wizard turns on the Wi-Fi radio, which allows you to connect wirelessly. For more advanced configurations, see the Administration Guide. A link to the Administration Guide is found in Where to Go From Here.Congratulations, you can now start using your wireless access point.
Cisco WAP571E Wireless Access Point 12Suggested Next StepsSmart PoESmart PoE is designed for detecting the power level from the PSE (Power Sourcing Equipment) side; it does not matter whether 802.3at or 802.3af mode, the WAP571 will operate at the appropriate mode automatically. Smart PoE ensures that the WAP571E remains functional once powered by 802.3af PSE, and intelligently to adjust operations below:•Second Ethernet port disabled•2.4-GHz 802.11n radio in 2x2:2 spatial-stream mode•5-GHz 802.11ac radio operates without restrictionsIn case of an error while installing, try the following troubleshooting procedures described in this section:TroubleshootingIf you cannot display the configuration utility, you can test the ability of the computer to communicate with the device by using ping. To u s e ping on a computer running Windows:STEP 1Verify that the Cisco WAP571E is powered on and the lights indicate the appropriate links.STEP 2Locate the device’s IP address. While there are different ways to locate your device’s IP address, this procedure uses Cisco FindIT.a. If you have previously downloaded Cisco FindIT, open Internet Explorer and launch Cisco FindIT. For more information on downloading Cisco FindIT, see www.cisco.com/go/findit.b. In the Cisco FindIT display, place your mouse over the device’s name. The device IP address is displayed along with other device information.STEP 3Open a command window by choosing Start > Run and enter cmd.STEP 4At the command window prompt, enter ping and the device IP address. In this example, we pinged 192.0.2.10. If successful, you should get a reply similar to the following:Pinging 192.0.2.10 with 32 bytes of data:Reply from 192.0.2.10: bytes=32 time<1ms TTL=1287
13 Cisco WAP571E Wireless Access PointIf it fails, you should get a reply similar to the following:Pinging 192.0.2.10 with 32 bytes of data:Request timed out.Possible Cause of Installation FailureNo Power•Power up the switch and your computer if they are turned off.•Make sure your PoE switch is powered on and the lights indicate that you have a link. See Verifying the Hardware Installation.•Verify that the devices on your network are not plugged into a switchable outlet.Bad Ethernet Connection•Check the state of the indicator lights. See Verifying the Hardware Installation.•Check the Ethernet cable to ensure that it is firmly connected to your devices. Devices connected by the Ethernet cable can include the WAP device, and routers, any switches, and your computer.•Verify the connected switch has auto-negotiation enabled. The access point and the switch need the same negotiation parameters set.Bad ImageAfter a new firmware installation, if the Power light is solid red, contact system support; see Where to Go From Here.Incorrect IP AddressThe most likely cause of connectivity failure is an incorrect IP address. The Web browser may be pointing to the wrong IP address, or your computer may be configured with an IP address that is not in the same subnet as the device.Because the factory default IP address configuration is DHCP, make sure that your DHCP server is running and can be reached. You may need to disconnect and reconnect the devices for them to discover their new IP addresses from the DHCP server. You can then query the DHCP server for the new IP address. See Step 2 of Getting Started with the Configuration for more information on how to find the DHCP address.
Cisco WAP571E Wireless Access Point 14If the wireless access points do not receive a DHCP response (there is no DHCP server on your network) after 60 seconds, the access points will fallback to the following default static IP address: 192.168.1.245 and a default mask of 255.255.255.0. To reach that IP address, be sure that your computer is on the 192.168.1.xxx network.Rebooting the Devices or Returning them to their Factory Default SettingsTo reboot your device:•The Cisco WAP571 uses PoE power supply; unplug your Ethernet connection and plug it back in.or•With the power on, press the Reset button with an opened paper clip for less than three seconds, or until the lights go off. – Release the Reset button as soon as the lights go off, or you will restore the device to factory default settings and lose your configurations.– Release the Reset button when the system light turns on. To reset the device to factory default settings:•With the power on, press and hold the Reset button with an opened paper clip for more than 10 seconds. The system light will go off.Where to Go From HereSupportCisco Support Communitywww.cisco.com/go/smallbizsupportCisco Support and Resourceswww.cisco.com/go/smallbizhelpPhone Support Contacts www.cisco.com/en/US/support/tsd_cisco_small_business _support_center_contacts.html8
Americas HeadquartersCisco Systems, Inc.www.cisco.comCisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbersare listed on the Cisco website atwww.cisco.com/go/offices.Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliatesin the U.S. and other countries. To view a list of Ciscotrademarks, go to this URL:www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of theirrespective owners. The use of the word partner does not imply a partnership relationshipbetween Cisco and any other company. (1110R)© 2015 Cisco Systems, Inc. All rights reserved. 78-100813-01 A0For EU lot 26 related test result, please check this web page: www.cisco.com/go/eu-lot26-results. Cisco Firmware Downloadswww.cisco.com/go/smallbizfirmwareSelect a link to download firmware for Cisco Products. No login is required.Cisco Open Source Requestswww.cisco.com/go/smallbiz_opensource_requestCisco Partner Central (Partner Login Required)www.cisco.com/web/partners/sell/smbProduct DocumentationCisco WAP571E Administration Guide www.cisco.com/go/300_wap_resourcesCisco Power Adapters www.cisco.com/go/wap_accessories
Americas Headquarters:Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USARegulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)This document provides domestic and international regulatory compliance and safety information for the Cisco WAP571/571E Wireless Access Point EMC Class B Devices.Use this document in conjunction with the documentation available online for the Wireless Access Points.This document includes the following sections: • Translated Safety Warnings, page 1 • Product Usage Restrictions, page 22 • Declaration of Conformity Statements, page 22 • European Directives, page 22 • EU Battery Disposal and Recycling, page 24 • Standards Compliance, page 24 • EMC Class B Notices and Warnings, page 25 • Japanese Electric Appliance and Radio Laws, page 28 • Radio, page 28 • Canadian Radio Warning Statement, page 28 • Generic Discussion on RF Exposure, page 31 • Obtaining Documentation and Submitting a Service Request, page 32Translated Safety WarningsThis section includes translations in multiple languages of the warnings that may appear in your product documents. • Statement 1071—Warning Definition
2Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Translated Safety Warnings • Statement 1—Power Disconnection Warning • Statement 248—Unit Mounting Warning • Statement 1004—Installation Instructions • Statement 1005—Circuit Breaker • Statement 1040—Product Disposal • Statement 1044—Port Connections • Statement 1072—Shock Hazard from Interconnections • Statement 1073—No User-Serviceable Parts • Statement 1074—Comply with Local and National Electrical CodesStatement 1071—Warning DefinitionWarningIMPORTANT SAFETY INSTRUCTIONSThis warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071SAVE THESE INSTRUCTIONSWaarschuwingBELANGRIJKE VEILIGHEIDSINSTRUCTIESDit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.BEWAAR DEZE INSTRUCTIESVaroitusTÄRKEITÄ TURVALLISUUSOHJEITATämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.SÄILYTÄ NÄMÄ OHJEET
3Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Translated Safety WarningsAttentionIMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.CONSERVEZ CES INFORMATIONSWarnungWICHTIGE SICHERHEITSHINWEISEDieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.BEWAHREN SIE DIESE HINWEISE GUT AUF.AvvertenzaIMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento. CONSERVARE QUESTE ISTRUZIONIAdvarselVIKTIGE SIKKERHETSINSTRUKSJONERDette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.TA VARE PÅ DISSE INSTRUKSJONENEAvisoINSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.GUARDE ESTAS INSTRUÇÕES
4Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Translated Safety Warnings¡Advertencia!INSTRUCCIONES IMPORTANTES DE SEGURIDADEste símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo. GUARDE ESTAS INSTRUCCIONESVarning!VIKTIGA SÄKERHETSANVISNINGARDenna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.SPARA DESSA ANVISNINGAR
5Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Translated Safety WarningsAvisoINSTRUÇÕES IMPORTANTES DE SEGURANÇAEste símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.GUARDE ESTAS INSTRUÇÕESAdvarselVIGTIGE SIKKERHEDSANVISNINGERDette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.GEM DISSE ANVISNINGER
6Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Translated Safety Warnings
7Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Translated Safety WarningsStatement 1—Power Disconnection WarningWarningBefore working on a system that has an on/off switch, turn OFF the power and unplug the power cord. WaarschuwingVoordat u aan een systeem werkt dat een aan/uit schakelaar heeft, dient u de stroomvoorziening UIT te schakelen en de stekker van het netsnoer uit het stopcontact te halen.
8Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Translated Safety WarningsVaroitusEnnen kuin teet mitään sellaiselle järjestelmälle, jossa on kaksiasentokytkin, katkaise siitä virta ja kytke virtajohto irti.AttentionAvant de travailler sur un système équipé d'un commutateur marche-arrêt, mettre l'appareil à l'arrêt (OFF) et débrancher le cordon d'alimentation.WarnungBevor Sie an einem System mit Ein/Aus-Schalter arbeiten, schalten Sie das System AUS und ziehen das Netzkabel aus der Steckdose.AvvertenzaPrima di lavorare su un sistema dotato di un interruttore on/off, spegnere (OFF) il sistema e staccare il cavo dell’alimentazione.AdvarselSlå AV strømmen og trekk ut strømledningen før det utføres arbeid på et system som er utstyrt med en av/på-bryter.AvisoAntes de começar a trabalhar num sistema que tem um interruptor on/off, DESLIGUE a corrente eléctrica e retire o cabo de alimentação da tomada.¡Advertencia!Antes de utilizar cualquier sistema equipado con interruptor de Encendido/Apagado (ON/OFF), cortar la alimentación y desenchufar el cable de alimentación.Varning!Slå AV strömmen och dra ur nätsladden innan du utför arbete på ett system med strömbrytare.
9Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Translated Safety WarningsStatement 248—Unit Mounting WarningWarningThis unit is intended to be mounted on a wall. Please read the wall mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.WaarschuwingDeze eenheid dient aan een wand te worden bevestigd. Lees voordat u met de installatie begint, de instructies voor wandmontage aandachtig door. Het niet gebruiken van de juiste apparatuur of het niet volgen van de juiste procedures kan leiden tot gevaarlijke situaties of beschadiging van het systeem. VaroitusTämä laite on tarkoitettu seinälle asennettavaksi. Lue seinäasennusohjeet huolellisesti ennen asennuksen aloittamista. Väärien työkalujen käyttäminen tai ohjeiden noudattamatta jättäminen voi aiheuttaa henkilövahinkoja ja vioittaa laitetta.AttentionCette unité est conçue pour être montée sur un mur. Veuillez lire attentivement les instructions de montage avant de commencer l'installation. L'utilisation d'un matériel incorrect ou l'application inappropriée des procédures peut être à l'origine d'accidents et endommager le système.WarnungDiese Einheit ist für die Montage an einer Wand bestimmt. Lesen Sie die Montageanweisungen sorgfältig durch, bevor Sie mit der Installation beginnen. Nichtverwenden der korrekten Hardware oder Nichtbefolgen der korrekten Vorgehensweise stellt eine potentielle Gefahrenquelle dar und könnte das System beschädigen.AvvertenzaL’unità deve essere montata a parete. Leggere attentamente le istruzioni di montaggio a parete prima di procedere all’installazione. L’impiego di utensili non adeguati o di procedure non corrette può comportare un rischio per le persone e per il sistema stesso.AdvarselDenne enheten er beregnet på veggmontering. Les instruksjonene om veggmontering nøye før du begynner installeringen. Hvis du ikke bruker riktig maskinutstyr eller følger de korrekte prosedyrer, kan det medføre risiko for personskade og skade på systemet. AvisoEsta unidade foi concebida para ser montada numa parede. Leia atentamente as instruções de montagem em parede antes de iniciar a instalação. A utilização de material incorrecto ou o não seguimento dos procedimentos correctos podem dar origem a uma situação perigosa para o pessoal e danificar o sistema.¡Advertencia!Esta unidad está diseñada para ser montada en la pared. Leer las instrucciones de montaje en pared cuidadosamente antes de comenzar la instalación. En caso de no utilizar los materiales apropiados o no seguir el procedimiento correcto, se podría crear una situación peligrosa y ocasionar daños al sistema.Varning!Den här enheten är utformad för väggmontering. Läs noga anvisningarna för väggmontering innan du börjar installera. Om du inte använder rätt maskinvara eller inte följer anvisningarna kan det orsaka fara för personskada eller skador på systemet.
10Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Translated Safety WarningsStatement 1004—Installation InstructionsWarningRead the installation instructions before connecting the system to the power source. Statement 1004WaarschuwingRaadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit.VaroitusLue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen.AttentionAvant de brancher le système sur la source d'alimentation, consulter les directives d'installation.WarnungVor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen.AvvertenzaConsultare le istruzioni di installazione prima di collegare il sistema all'alimentatore.AdvarselLes installasjonsinstruksjonene før systemet kobles til strømkilden.AvisoLeia as instruções de instalação antes de ligar o sistema à fonte de energia.¡Advertencia!Lea las instrucciones de instalación antes de conectar el sistema a la red de alimentación.Varning!Läs installationsanvisningarna innan du kopplar systemet till strömförsörjningsenheten.
11Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Translated Safety WarningsStatement 1005—Circuit BreakerWarningThis product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 15 A, 125 Vac, or 10A, 240 Vac. Statement 1005WaarschuwingDit product is afhankelijk van de installatie van het gebouw voor beveiliging tegen kortsluiting (overstroom). Controleer of de beschermingsinrichting niet meer dan: 15 A, 125 Vac, or 10A, 240 Vac is.VaroitusTämä tuote on riippuvainen rakennukseen asennetusta oikosulkusuojauksesta (ylivirtasuojauksesta). Varmista, että suojalaitteen mitoitus ei ole yli: 15 A, 125 Vac, or 10A, 240 Vac.AttentionPour ce qui est de la protection contre les courts-circuits (surtension), ce produit dépend de l'installation électrique du local. Vérifiez que le courant nominal du dispositif de protection n'est pas supérieur à : 15 A, 125 Vac, or 10A, 240 Vac.WarnungDieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss- bzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der Schutzvorrichtung nicht mehr als: 15 A, 125 Vac, or 10A, 240 Vac beträgt.AvvertenzaQuesto prodotto dipende dall'impianto dell'edificio per quanto riguarda la protezione contro cortocircuiti (sovracorrente). Assicurarsi che il dispositivo di protezione non abbia un rating superiore a: 15 A, 125 Vac, or 10A, 240 Vac.AdvarselDette produktet er avhengig av bygningens installasjoner av kortslutnings (overstrøm)-beskyttelse. Påse at verneenheten ikke er merket høyere enn: 15 A, 125 Vac, or 10A, 240 Vac.
12Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Translated Safety WarningsStatement 1040—Product DisposalAvisoEste produto depende das instalações existentes para proteção contra curto-circuito (sobrecarga). Assegure-se de que o fusível ou disjuntor não seja superior a: 15 A, 125 Vac, or 10A, 240 Vac.¡Advertencia!Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes) del edificio. Asegúrese de que el dispositivo de protección no sea superior a: 15 A, 125 Vac, or 10A, 240 Vac.Varning!Denna produkt är beroende av i byggnaden installerat kortslutningsskydd (överströmsskydd). Kontrollera att skyddsanordningen inte har högre märkvärde än: 15 A, 125 Vac, or 10A, 240 Vac.15 A, 125 Vac, or 10A, 240 Vac.15 A, 125 Vac, or 10A, 240 Vac.15 A, 125 Vac, or 10A, 240 Vac.15 A, 125 Vac, or 10A, 240 Vac.WarningUltimate disposal of this product should be handled according to all national laws and regulations. Statement 1040WaarschuwingHet uiteindelijke wegruimen van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen.VaroitusTämä tuote on hävitettävä kansallisten lakien ja määräysten mukaisesti.AttentionLa mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent.WarnungDie Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen des Landes erfolgen.
13Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Translated Safety WarningsAvvertenzaLo smaltimento di questo prodotto deve essere eseguito secondo le leggi e regolazioni locali.AdvarselEndelig kassering av dette produktet skal være i henhold til alle relevante nasjonale lover og bestemmelser.AvisoDeitar fora este produto em conformidade com todas as leis e regulamentos nacionais.¡Advertencia!Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales.Varning!Vid deponering hanteras produkten enligt gällande lagar och bestämmelser. AvisoO descarte definitivo deste produto deve estar de acordo com todas as leis e regulamentações nacionais.AdvarselEndelig bortskaffelse af dette produkt skal ske i henhold til gældende love og regler.
14Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Translated Safety WarningsStatement 1044—Port ConnectionsWarningFor connections outside the building where the equipment is installed, the following ports must be connected through an approved network termination unit with integral circuit protection.10/100/1000 Ethernet Statement 1044WaarschuwingVoor aansluitingen buiten het gebouw waar de apparatuur wordt geïnstalleerd, dienen de volgende poorten aangesloten te worden via een goedgekeurde netwerkafsluiteenheid met integrale circuitbescherming.10/100/1000 EthernetVaroitusAsennuksen sisältävän rakennuksen ulkopuolisia liitäntöjä varten seuraavat portit on kytkettävä hyväksytyn verkon päätelaitteen kautta ja virtapiirin on oltava kiinteästi suojattu.10/100/1000 EthernetAttentionPour les connexions extérieures au bâtiment équipé, les ports suivants doivent être connectés à un point approuvé de terminaison de réseau, avec protection complète du circuit.10/100/1000 EthernetWarnungFür Verbindungen außerhalb des Gebäudes, in dem das Gerät installiert ist, müssen die folgenden Anschlüsse über eine zulässige Netzabschlusseinheit mit integralem Leitungsschutz verbunden werden.10/100/1000 EthernetAvvertenzaPer le connessioni esterne all'edificio in cui è installato l'apparecchio, le seguenti porte devono essere connesse a un'unità di terminazione di rete approvata, con protezione completa del circuito.10/100/1000 EthernetAdvarselFor tilkoblinger utenfor bygningen der utstyret er montert, må følgende åpninger tilkobles gjennom en godkjent nettverksterminal med integrert kretsbeskyttelse.10/100/1000 Ethernet
15Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Translated Safety WarningsAvisoPara ligações fora do edifício onde o equipamento está instalado, é necessário ligar as seguintes portas através de uma unidade de terminal de rede aprovada com protecção de circuito integral.10/100/1000 Ethernet¡Advertencia!Para realizar conexiones en el exterior del edificio en el que esté instalado el equipo, deberá conectar los puertos especificados a continuación a una unidad terminal de red aprobada que cuente con protección de circuitos integrales.10/100/1000 EthernetVarning!För alla anslutningar utanför byggnaden där utrustningen har installerats gäller att följande portar måste anslutas genom en godkänd nätverksavslutningsenhet med integrerat kretsskydd. 10/100/1000 Ethernet10/100/1000 Ethernet10/100/1000 Ethernet10/100/1000 Ethernet10/100/1000 Ethernet10/100/1000 Ethernet10/100/1000 Ethernet10/100/1000 Ethernet10/100/1000 Ethernet
16Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Translated Safety WarningsStatement 1072—Shock Hazard from Interconnections10/100/1000 Ethernet10/100/1000 Ethernet10/100/1000 EthernetWarningVoltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if interconnections are made using uninsulated exposed metal contacts, conductors, or terminals. Avoid using such interconnection methods, unless the exposed metal parts are located within a restricted access location and users and service people who are authorized within the restricted access location are made aware of the hazard. A restricted access area can be accessed only through the use of a special tool, lock and key or other means of security. Statement 1072WaarschuwingVoltages kunnen elektrische schokken veroorzaken in PoE (Power over Ethernet)-circuits als er verbindingen worden gemaakt met blootliggende metalen contactpunten, geleiders of aansluitingspunten die niet zijn geïsoleerd. Gebruik dit type verbinding niet tenzij de blootliggende metalen onderdelen zich bevinden op een locatie met beperkte toegang en de gebruikers en onderhoudstechnici die toegang tot deze locatie hebben, op het gevaar worden gewezen. De locatie met beperkte toegang kan alleen worden geopend met speciaal gereedschap, slot en sleutel of een andere beveiligingsmethode.VaroitusSisäisissä Ethernet (PoE) -virtapiireissä voi olla sähköiskun vaaran aiheuttavia jännitteitä, jos kytkentöihin käytetään eristämättömiä paljaita metalliliittimiä tai -johtimia. Vältä tällaisia kytkentöjä, elleivät paljaat metalliosat ole rajatussa paikassa. Ilmoita valtuutetuille käyttäjille ja huoltohenkilöille vaarasta. Rajattuun alueeseen pääsee käsiksi ainoastaan erityistyökalua, lukkoa ja avainta tai muuta turvallista menetelmää käyttämällä.
17Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Translated Safety WarningsAttentionLes tensions existant sur les alimentations utilisant la technologie PoE (Power over Ethernet) peuvent constituer un risque d'électrocution si les interconnexions sont effectuées en utilisant des terminaux, conducteurs ou contacts métalliques exposés non isolés. Évitez d'utiliser de telles méthodes d'interconnexion à moins que les pièces métalliques exposées ne se trouvent dans un emplacement d'accès restreint et que les utilisateurs et les responsables du service autorisés dans cet emplacement d'accès restreint ne soient conscients du danger. Une zone d'accès restreint peut être accédée uniquement à l'aide d'une clé, d'un outil et d'un verrou spécial, ou d'autres moyens de sécurité.WarnungBei Power-over-Ethernet-(PoE-)Schaltkreisen besteht u.U. Stromschlaggefahr, wenn Verbindungen unter Verwendung nicht isolierter, freiliegender Metallkontakte, Leiter oder Anschlussklemmen hergestellt werden. Vermeiden Sie das Herstellen solcher Verbindungen, es sei denn, die freiliegenden Metallteile befinden sich an Orten mit beschränktem Zugang, und Personen, die Zugang dazu haben, sind ausdrücklich über diese Gefahr informiert worden. Ein Ort mit beschränktem Zugang ist nur mit Hilfe eines speziellen Werkzeugs, Schloss und Schlüssels oder anderen Sicherheitseinrichtungen zugänglich.AvvertenzaNei circuiti con alimentazione via Ethernet (PoE) possono verificarsi pericoli di scosse elettriche se si creano connessioni con contatti metallici, conduttori o terminali scoperti. Evitare di utilizzare i metodi di connessione sopraelencati a meno che le parti metalliche esposte non si trovino in una zona riservata e gli utenti e il personale di assistenza, che sono autorizzati ad accedere nella suddetta zona, siano stati messi al corrente del pericolo. È possibile accedere alla zona riservata solamente utilizzando gli appositi elementi di sicurezza.AdvarselI strømkretser med PoE (Power over Ethernet) kan det være spenninger som kan utgjøre støtfare hvis det blir foretatt sammenkoblinger med uisolerte, eksponerte kontakter, ledere eller terminaler av metall. Unngå å bruke slike sammenkoblingsmetoder med mindre de eksponerte metalldelene er i et område med begrenset tilgang, og brukere og servicepersonell som har tilgang til det begrensede området, blir gjort oppmerksom på faren. Et område med begrenset tilgang kan bare åpnes ved hjelp av spesialverktøy, nøkkel eller andre sikkerhetstiltak.AvisoPode haver voltagens que representam perigo de choque em circuitos PoE (Power over Ethernet) se as interconexões forem feitas utilizando-se terminais, condutores ou contatos de metal exposto e sem isolamento. Evite utilizar tais métodos de interconexão a não ser que as partes de metal expostas estejam em um local de acesso restrito e os usuários e o pessoal de serviço com acesso autorizado a este local restrito estejam cientes do perigo. Uma área de acesso restrito só pode ser acessada com o uso de uma ferramenta, fechadura e chave especial ou de outros meios de segurança.¡Advertencia!Puede haber voltajes con riesgo de shock en circuitos de alimentación sobre el cableado Ethernet (PoE), si para las interconexiones se utilizan contactos, conductores o terminales metálicos descubiertos. Evite tales métodos de interconexión, a menos que las partes metálicas descubiertas se encuentren en un lugar de acceso restringido y tanto los usuarios como el personal de servicios en dicho lugar sean conscientes de la existencia de tal riesgo. Sólo se puede tener acceso a una zona de acceso restringido mediante el uso de una herramienta especial, un candado y una llave u otros medios de seguridad.
18Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Translated Safety WarningsStatement 1073—No User-Serviceable PartsVarning!Det kan finnas spänningar på PoE-kretsarna (Power over Ethernet) som utgör risk för stötar om sammankopplingarna görs med ej isolerade, exponerade kontakter, ledare och/eller terminaler av metall. Undvik att använda sådana sammankopplingsmetoder, såvida inte de exponerade metalldelarna finns i en plats med begränsad åtkomst. Användare och servicepersonal som tillåts inom platsen med begränsad åtkomst måste vara medvetna om risken. Ett begränsat område kan bara nås med ett speciellt verktyg eller lås, en speciell nyckel eller någon annan säkerhetsmetod.WarningNo user-serviceable parts inside. Do not open. Statement 1073WaarschuwingEr zijn geen door de gebruiker te vervangen onderdelen. Niet openen.
19Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Translated Safety WarningsVaroitusEi sisällä käyttäjän huollettavissa olevia osia. Älä avaa.AttentionAucune pièce se trouvant à l'intérieur ne peut être réparée ou remplacée par l'utilisateur. Ne pas ouvrir.WarnungEnthält keine Teile, die vom Benutzer gewartet werden müssen. Bitte nicht öffnen.AvvertenzaNon contiene parti riparabili dall'utente. Non aprire.AdvarselInneholder ingen deler som kan repareres av brukeren. Må ikke åpnes.AvisoSem peças sujeitas a manutenção pelo utilizador. Não abrir.¡Advertencia!No contiene partes que puedan ser arregladas por el usuario. No abrir.Varning!Det finns inga delar som användare kan utföra service på. Öppna inte.AvisoManutenção somente por técnico especializado. Não abra.AdvarselIngen dele indeni som brugere kan reparere. Åbn ej.
20Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Translated Safety WarningsStatement 1074—Comply with Local and National Electrical CodesWarningInstallation of the equipment must comply with local and national electrical codes. WaarschuwingBij installatie van de apparatuur moet worden voldaan aan de lokale en nationale elektriciteitsvoorschriften. VaroitusLaitteisto tulee asentaa paikallisten ja kansallisten sähkömääräysten mukaisesti.AttentionL'équipement doit être installé conformément aux normes électriques nationales et locales.WarnungDie Installation der Geräte muss den Sicherheitsstandards entsprechen.AvvertenzaL'installazione dell'impianto deve essere conforme ai codici elettrici locali e nazionali.AdvarselInstallasjon av utstyret må samsvare med lokale og nasjonale elektrisitetsforskrifter.AvisoA instalação do equipamento tem de estar em conformidade com os códigos eléctricos locais e nacionais. ¡Advertencia!La instalación del equipo debe cumplir con las normativas de electricidad locales y nacionales.Varning!Installation av utrustningen måste ske i enlighet med gällande elinstallationsföreskrifter.
21Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Translated Safety Warnings
22Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Product Usage RestrictionsProduct Usage RestrictionsThe Cisco WAP571/571E Wireless Access Points are intended for indoor use only.Declaration of Conformity StatementsThe Declaration of Conformity statements for this product can be found at the following URL:http://www.ciscofax.comNote If you still have questions regarding the compliance of these products or you cannot find the information you are looking for, please send an e-email request to complianceinfo@cisco.com.European Directives Statement 287—Declaration of Conformity to R&TTE Directive 1999/5/EC for the European Community, Switzerland, Norway, Iceland and LiechtensteinEnglish:This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.[Bulgarian]: [Czech]: Dansk [Danish]:Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i Direktiv 1999/5/EF.Deutsch [German]:Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU.Eesti [Estonian]: See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele asjakohastele sätetele.Español [Spanish]:Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva 1999/5/CE.[Greek]: The CISCO WAP571 Wireless Access Point are intended for indoor use only.
23Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 European DirectivesFrançais [French]:Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999/5/EC.Hrvatski: [Croatian]Ova oprema je u sukladnosti s bitnim zahtjevima i drugim relevantnim odredbama Direktive 1999/5/EC.Íslenska [Icelandic]:Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar 1999/5/EC.Italiano [Italian]:Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/CE.Latviski [Latvian]: [Lithuanian]: Nederlands [Dutch]:Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de Richtlijn 1999/5/EC.Malti [Maltese]: Magyar [Hungarian]: Norsk [Norwegian]:Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-direktiv 1999/5/EF.Polski [Polish]: Português [Portuguese]:Este equipamento está em conformidade com os requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC.[Romanian]: Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi relevante ale Directivei 1999/5/EC.Slovensko [Slovenian]: Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji Direktive 1999/5/EC.Slovensky [Slovak]: Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými nariadeniami direktív: 1999/5/EC. Suomi [Finnish]:
24Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 EU Battery Disposal and RecyclingDeclaration of Conformity with Regard to the Directives 2006/95/EC and 2004/108/ECThis equipment complies with the essential requirements and other provisions of Directives 2006/95/EC and 2004/108/EC. For more information, please refer to the Declaration of Conformity.EU Battery Disposal and RecyclingThis product may contain a battery. Recycle or dispose of batteries in accordance w\ith the battery manufacturer’s instructions and local/national disposal and recycling regulations.Standards Compliance The following CE mark is affixed to the equipment and packaging:This section includes all regulatory, safety, EMC, telecom, and radio standards used to verify compliance with the EU Directive (Directive 2006/95/EC and 2004/108/EC for products without antenna or antenna connectors and Directive 1995/5/EC for products with antenna or antenna connectors). The Cisco WAP571/571E Wireless Access Points are in compliance with national and international standards as described in Table 1.Türk [Turkish]:Bu cihaz 1999/5/EC Direktifi'nin temel gereklerine ve ilgili di?er hükümlerine uygundur.Svenska [Swedish]: Table 1 Specification DescriptionEU Compliance (CE Mark) Products with CE marking indicate compliance with the Low Voltage Directive 2006/95/EC, EMC Directive 2004/108/EC or R&TTE Directive 1999/5/EC. Safety UL 60950-1 CAN/CSA-C22.2 No. 60950-1 EN 60950-1 IEC 60950-1 AS/NZS 60950-1
25Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 EMC Class B Notices and WarningsFor specific details about the years, revisions and relevant amendments please refer to the applicable declaration of conformity available at http://www.ciscofax.com.EMC Class B Notices and WarningsThis section includes the EMC Class B warnings for the Cisco WAP571/571E Wireless Access Point.Class B Notice for FCCModifying the equipment without Cisco’s authorization may result in the equipment no longer complying with FCC requirements for Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver.EMC 47CFR FCC Part 15BIndustry Canada ICES-003 EN 301 489-1, EN 301 489-17 EN 300 386EN55022 EN55024 EN61000-3-2 EN61000-3-3 CISPR 22 CISPR 24 AS/NZS CISPR22 Radio 47CFR FCC Part 15C Industry Canada RSS-210 EN 300 328 EN 301893AS/NZS 4268RF Exposure FCC OET 65, Supplement C RSS-102 EN 50385 Table 1 (continued)Specification DescriptionRSS-247
26Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 EMC Class B Notices and Warnings • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
27Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 EMC Class B Notices and WarningsClass B Notice for CanadaThis Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.Statement 295—Class B Warning for KoreaStatement 157—VCCI Compliance for Class B EquipmentWarningThis is a Class B Device and is registered for EMC requirements for residential use. This device can be used not only in residential areas but in all other areas.WarningThis is a Class B product based on the standard of the VCCI Council. If this is used near a radio or television receiver in a domestic environment, it may cause radio Interference. Install and use the equipment according to the instruction manual. VCCI-B
28Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Japanese Electric Appliance and Radio LawsJapanese Electric Appliance and Radio LawsStatement 571/571E—Power Cable and AC AdapterRadioThis section describes radio compliance conditions for the Cisco WAP571/571E Wireless Access Points EMC Class B Devices.Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when using the integrated antennas. Any changes or modification to the product not expressly approved by Cisco could void the user’s authority to operate this device.Canadian Radio Warning StatementThis device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme aÌ la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage preìjudiciable, et (2) ce dispositif doit accepter tout brouillage rec?u, y compris un brouillage susceptible de provoquer un fonctionnement indeìsirable. WarningWhen installing the product, please use the provided or designated connection cables/power cables/AC adaptors/batteries. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” or “CSA” shown on the cord), not regulated with the subject law by showing "PSE" on the cord, for any other electrical devices than products designated by CISCO.RSS-247CNR-247
29Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 RadioGuidelines for Operating Cisco WAP571/571E Wireless Access Points in JapanThis section provides guidelines for avoiding interference when operating Cisco WAP571/571E Wireless Access Points in Japan. These guidelines are provided in both English and Japanese.Statement 391—Warning for Low-Power Radio Data Communications Systems (-STD)WarningThis equipment shares a frequency band with a wide range of equipment: e.g. industrial, scientific, and medical equipment such as microwave ovens, premises radio stations (radio stations requiring licenses), and specified low-power radio stations (radio stations not requiring licenses) for RFID used for factory production lines as well as amateur radio stations (radio stations requiring licenses).1. Before use, confirm that no premises radio stations and specified low-power radio stations for RFID or amateur radio stations operate in your vicinity.2. In the event that this equipment causes harmful interference to any premises radio station for RFID, immediately change frequencies or halt radio wave emission and contact us at the information indicated below for consultation on interference avoidance measures (e.g., partition installation).3. Contact us at the information indicated below if this equipment causes harmful interference to any specified low-power radio stations for RFID or amateur radio stations or if other problems arise. Statement 391Contact us at : http://www.cisco.com/web/JP/index.html
30Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 RadioAdministrative Rules for Cisco Wireless Devices in TaiwanThis section provides administrative rules for operating Cisco wireless access products in Taiwan. The rules are provided in both Chinese and English.Wireless Devices with IEEE 802.11a/b/g RadiosChinese TranslationEnglish TranslationThis equipment is limited for indoor use.All Access Wireless ProductsChinese Translation
31Regulatory Compliance and Safety Information for the Cisco WAP571/571E Wireless Access Point (EMC Class B Devices)78-20515-02 Generic Discussion on RF ExposureEnglish TranslationAdministrative Rules for Low-Power Radio-Frequency DevicesArticle 12For those low-power radio-frequency devices that have already received a type-approval, companies, business units, or users should not change its frequencies, increase its power, or change its original features and functions.Article 14The operation of the low-power radio-frequency devices is subject to the conditions that no harmful interference is caused to aviation safety and authorized radio stations; and if interference is caused, the user must stop operating the device immediately and can’t re-operate it until the harmful interference is clear.The authorized radio station means a radio-communication service operating in accordance with the Communication Act.The operation of the low-power radio-frequency devices is subject to the interference caused by the operation of an authorized radio station, by another intentional or unintentional radiator, by industrial, scientific and medical (ISM) equipment, or by an incidental radiator.Generic Discussion on RF ExposureThe Cisco WAP571/571E Wireless Access Points are designed to comply with the following national and international standards on Human Exposure to Radio Frequencies. • US 47 Code of Federal Regulations Part 2 Subpart J • American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers / IEEE C 95.1 (92) • International Commission on Non Ionizing Radiation Protection (ICNIRP) 98 • Ministry of Health (Canada) Safety Code 6. Limits on Human Exposure to Radio Frequency Fields in the range from 3kHz to 300 GHz • Australia Radiation Protection StandardTo ensure compliance with various national and international Electromagnetic Field (EMF) standards, the system should only be operated with Cisco approved antennas and accessories.USThis system has been evaluated for RF exposure for Humans in reference to ANSI C 95.1 (American National Standards Institute) limits. The evaluation was based on evaluation per ANI C 95.1 and FCC OET Bulletin 65C rev 01.01. The minimum separation distance from the antenna to general bystander is 7.9 inches (20cm) to maintain compliance.CanadaThis system has been evaluated for RF Exposure per RSS-102 and is in compliance with the limits specified by Health Canada Safety Code 6. The system must be installed at a minimum separation distance from the antenna to a general bystander of 7.9 inches (20cm) to maintain compliance with the General Populace limits. L’exposition aux radiofréquences de ce système a été évaluée selon la norme RSS-102 et est jugée conforme aux limites établies par le Code de sécurité 6 de Santé Canada. Le système doit être installé à une distance minimale de 7,9 pouces (20 cm) séparant l’antenne d’une personne présente en conformité avec les limites permises d’exposition du grand public. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.This device and it's antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.

Navigation menu