POULAN Lawn, Tractor Manual L0604837
User Manual: POULAN POULAN Lawn, Tractor Manual POULAN Lawn, Tractor Owner's Manual, POULAN Lawn, Tractor installation guides
Open the PDF directly: View PDF 
.
Page Count: 30
| Download | |
| Open PDF In Browser | View PDF |
IMPORTANT MANUAL
Do Not Throw Away
OPERATOR'S MANUAL
WARNING:
MODEL:
Read this Manual and follow all Warnings and
Safety Instructions, Failure to do so can result
in serious injury,
HD1842
LAWN TRACTOR
ALWAYS WEAR EYE PROTECTION
DURING OPERATION
Visit our website: www.poulan-pro.com
195506 11,4,04 RD
Printed in U,S,A,
SAFETY
RULES
Practices for Ride-On
Safe Operation
IMPORTANT:
THIS CUTTING
MACHINE
IS CAPABLE
OF AMPUTATING
HANDS
Mowers
AND FEET AND THROWING
OBJECTS
FAILURE
TO OBSERVETHE FOLLOWINGSAFETY INSTRUCTIONSCOULD RESULTIN SERIOUS INJURYOR DEATH
•
WARNING: In order to prevent accidental starting when setting up,
transporting, adjusting or making repairs, always disconnect spark plug
wire and place wire where it cannot
contact spark plug.
•
•
•
I
I_
in neutral, you may lose control of the
WARNING:
Do not coast down a hill
tractor.
I
I
•
•
WARNING: Tow only the attachments
that are recommended by and comply with specifications of the manufacturer of your tractor. Use common
sense when towing. Operate only at
the lowest possible speed when on a
slope. Too heavy of a load, while on
a slope, is dangerous. Tires can lose
traction with the ground and cause you
to lose control of your tractor.
•
•
•
•
WARNING
•
Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals
known to the State of California to cause cancer and
birth defects or other reproductive harm.
•
WARNING
II. SLOPE OPERATION
Battery posts, terminals and related accessories
contain lead and lead compounds, chemicals known
to the State of California to cause cancer and birth
Slopes are a major factor related to loss of control and
tip-over accidents, which can result in severe injury or
death. Operation on all slopes requires extra caution. If
you cannot back up the slope or if you feel uneasy on it,
do not mow it.
defects or other reproductive harm. Wash hands
after handling.
I. GENERAL
•
•
•
•
•
•
•
•
•
•
OPERATION
Read, understand, and follow all instructions on the
machine and in the manual before starting
Do not put hands or feet near rotating parts or under
the machine Keep clear of the discharge opening at
all times
Only allow responsible adults, who are familiar with the
instructions, to operate the machine
Clear the area of objects such as rocks, toys, wire, etc,
which could be picked up and thrown by the blades
Be sure the area is clear of bystanders before operating Stop machine if anyone enters the area
Never carry passengers
Do not mow in reverse unless absolutely necessary
Always look down and behind before and while backing
Never direct discharged material toward anyone Avoid
discharging material against a wall or obstruction Material may ricochet back toward the operator Stop the
blades when crossing gravel surfaces.
Do not operate machine without the entire grass catcher,
discharge guard, or other safety devices in place and
working.
Slow down before turning.
Never leave a running machine unattended. Always
turn off blades, set parking brake, stop engine, and
remove keys before dismounting.
Disengage blades when not mowing. Shut off engine
and wait for all parts to come to a complete stop before
cleaning the machine, removing the grass catcher, or
unclogging the discharge guard.
Operate machine only in daylight or good artificial
light.
Do not operate the machine while under the influence
of alcohol or drugs.
Watch for traffic when operating near or crossing roadways.
Use extra care when loading or unloading the machine
into a trailer or truck.
Always wear eye protection when operating machine.
Data indicates that operators, age 60 years and above,
are involved in a large percentage of riding mower-related injuries. These operators should evaluate their
ability to operate the riding mower safely enough to
protect themselves and others from serious injury.
Follow the manufacturer's recommendation for wheel
weights or counterweights.
Keep machine free of grass, leaves or other debris
build-up which can touch hot exhaust / engine parts
and burn. Do not allow the mower deck to plow leaves
or other debris which can cause build-up to occur.
Clean any oil or fuel spillage before operating or
storing the machine. Allow machine to cool before
storage.
•
•
•
•
•
•
•
2
Mow up and down slopes, not across.
Watch for holes, ruts, bumps, rocks, or other hidden
objects. Uneven terrain could overturn the machine.
Tall grass can hide obstacles.
Choose a low ground speed so that you will not have
to stop or shift while on the slope.
Do not mow on wet grass. Tires may lose traction.
Always keep the machine in gear when going down
slopes. Do not shift to neutral and coast downhill.
Avoid starting, stopping, or turning on a slope. If the
tires lose traction, disengage the blades and proceed
slowly straight down the slope.
Keep all movement on the slopes slow and gradual.
Do not make sudden changes in speed or direction,
which could cause the machine to roll over.
Use extra care while operating machine with grass
catchers or other attachments; they can affect the
stability of the machine. Do no use on steep slopes.
Do not try to stabilize the machine by putting your foot
on the ground.
Do not mow near drop-offs, ditches, or embankments.
The machine could suddenly roll over if a wheel is over
the edge or if the edge caves in.
SAFETY
RULES
Practices for Ride-On
Safe Operation
III. CHILDREN
Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
the machine and the mowing activity. Never assume that
children will remain where you last saw them,
•
Keep children out of the mowing area and in the watchful
care of a responsible adult other than the operator.
•
Be alert and turn machine off if a child enters the
area.
•
Before and while backing, look behind and down for
small children.
•
Never carry children, even with the blades shut off, They
may fall off and be seriously injured or interfere with
safe machine operation, Children who have been given
rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over
by the machine.
•
Never allow children to operate the machine.
•
Use extra care when approaching blind corners, shrubs,
trees, or other objects that may block your view of a
child,
IV. TOWING
•
•
•
•
•
Tow only with a machine that has a hitch designed for
towing. Do not attach towed equipment except at the
hitch point,
Follow the manufacturer's recommendation for weight
limits for towed equipment and towing on slopes.
Never allow children or others in or on towed equipment.
On slopes, the weight of the towed equipment may
cause loss of traction and loss of control.
Travel slowly and allow extra distance to stop,
To avoid personal injury or property damage, use extreme
care in handling gasoline, Gasoline is extremely flammable
and the vapors are explosive,
•
Extinguish all cigarettes, cigars, pipes, and other
sources of ignition,
•
Use only approved gasoline container,
•
Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling,
•
Never fuel the machine indoors.
•
Never store the machine or fuel container where there
is an open flame, spark, or pilot light such as on a water
heater or other appliances,
•
Never fill containers inside a vehicle or on a truck or
trailer bed with plastic liner, Always place containers
on the ground away from your vehicle when filling,
•
Remove gas-powered equipment from the truck ortrailer
and refuel it on the ground, If this is not possible, then
refuel such equipment with a portable container, rather
than from a gasoline dispenser nozzle.
•
Keep the nozzle in contact with the rim of the fuel tank
or container opening atall times until fueling is complete,
Do not use a nozzle lock-open device,
•
If fuel is spilled on clothing, change clothing immediately.
•
Never overfill fuel tank. Replace gas cap and tighten
securely.
&
GENERAL SERVICE
•
Never operate machine in a closed are,
•
Keep all nuts and bolts tight to be sure the equipment
is in safe working condition.
•
Never tamper with safety devices, Check their proper
operation regularly,
•
Keep machine free of grass, leaves, or other debris
build-up. Clean oil or fuel spillage and remove any fuelsoaked debris, Allow machine to cool before storing.
•
If you strike a foreign object, stop and inspect the
machine. Repair, if necessary, before restarting.
•
Never make any adjustments or repairs with the engine
running.
•
Check grass catcher components and the discharge
guard frequently and replace with manufacturer's recommended parts, when necessary,
•
Mower blades are sharp, Wrap the blade or wear
gloves, and use extra caution when servicing them.
•
Check brake operation frequently. Adjust and service
as required.
•
Maintain or replace safety and instruction labels, as
necessary,
•
•
•
V. SERVICE
SAFE HANDLING OF GASOLINE
Mowers
•
•
•
•
•
•
•
•
•
Be sure the area is clear of bystanders before operating, Stop machine if anyone enters the area.
Never carry passengers.
Do not mow in reverse unless absolutely necessary,
Always look down and behind before and while backing,
Never carry children, even with the blades shut off, They
may fall off and be seriously injured or interfere with
safe machine operation. Children who have been given
rides in the past may suddenly appear in the mowing
area for another ride and be run over or backed over
by the machine,
Keep children out of the mowing area and in the watchful
care of a responsible adult other than the operator,
Be alert and turn machine off if a child enters the
area,
Before and while backing, look behind and down for
small children.
Mow up and down slopes (15 ° Max), not across,
Choose a low ground speed so that you will not have
to stop or shift while on the slope.
Avoid starting, stopping, or turning on a slope. If the
tires lose traction, disengage the blades and proceed
slowly straight down the slope,
If machine stops while going uphill, disengage blades,
shift into reverse and back down slowly.
Do not turn on slopes unless necessary, and then, turn
slowly and gradually downhill, if possible.
PRODUCT
GASOLINE
SPECIFICATIONS
CAPACITY
CONGRATULATIONS on your purchase of a new tractor.
It has been designed, engineered and manufactured to give
you the best possible dependability and performance.
1.25 GALLONS
AND TYPE:
UNLEADED REGULAR
OIL TYPE (API-SG-SL):
SAE 30 (above 32°F)
SAE 5W-30 (below 32°F)
W/FILTER 3.5 PINTS
W/O FILTER3.0 PINTS
OIL CAPACITY:
SPARKPLUG:
(GAP:
Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center/
department, We have competent, well-trained technicians
and the proper tools to service or repair this tractor.
Please read and retain this manual, The instructions will
enable you to assemble and maintain your tractor properly.
Always observe the "SAFETY RULES",
CHAMPION RC12YC
.030")
GROUND SPEED (MPH):
CUSTOMER
FORWARD:
1st 1.1
2nd 1.4
•
•
3rd 2.2
4th 3.3
•
5th 4.4
6th 4.9
TIRE PRESSURE:
REVERSE:
FRONT:
REAR:
3 AMPS BATTERY
5 AMPS HEADLIGHTS
BATTERY:
AMP/HR:
MIN. CCA:
BLADE BOLTTORQUE:
WARNING: This tractor is equipped with an internal combustion engine and should not be used on or near any
unimproved forest-covered, brush-covered or grass-covered
land unless the engine's exhaust system is equipped with
a spark arrester meeting applicable local or state laws (if
any), If a spark arrester is used, it should be maintained
in effective working order by the operator.
1.4
14 PSI
12 PSI
CHARGINGSYSTEM:
RESPONSIBILITIES
Read and observe the safety rules,
Follow a regular schedule in maintaining, caring for
and using your tractor.
Follow the instructions under "Maintenance" and "Storage" sections of this owner's manual.
A spark arrester for the muffler is available through your
nearest authorized service center/department,
28
230
CASE SIZE: U1R
27-35 FT.LBS.
TABLE OF CONTENTS
SAFETY RULES ......................................................... 2-3
PRODUCT SPECIFICATIONS ....................................... 4
CUSTOMER RESPONSIBILITIES ................................. 4
ASSEMBLY ................................................................. 6-8
OPERATION ............................................................. 9-14
MAINTENANCE SCHEDULE ...................................... 15
MAINTENANCE ..................................................... 15-18
SERVICE AND ADJUSTMENTS ............................ 19-23
STORAGE ....................................................................
24
TROUBLESHOOTING ............................................ 25-26
WARRANTY .................................................................
27
4
CONTENTS
OF HARDWARE
Steering Wheel
PACK
Seat
(1) Washer
Steering
Boot
@
17/32 x 1-3/16 x 12 Gauge
(1) Lock
Washer 1/2
Steering
Wheel
Insert
Steering
Extension
Shaft
(1) Bolt
Key
(1) Large Flat
Washer
(1) 5/16
Lock Washer
(2) Keys
Slope Sheet
Steering Wheel
Adapter
(1) Hex Bolt 5/16-18 x 4
ASSEMBLY
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes,
To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely, Use
the correct tools as necessary to insure proper tightness.
TOOLS
REQUIRED
FOR ASSEMBLY
A socket wrench set will make assembly easier. Standard
wrench sizes are listed.
(1) 1/2" wrench
Utility knife
Tire pressure gauge
Pliers
When right or left hand is mentioned in this manual, it means
when you are in the operating position (seated behind the
steering wheel),
TO REMOVE
TRACTOR
d_L.-------" LOCKWASHER
FROM
WHEEL
CARTON
UNPACK
CARTON
•
Remove all accessible loose parts and parts cartons
from carton.
•
Cut along dotted lines on all four panels of carton.
Remove end panels and lay side panels flat.
Check for any additional loose parts or cartons and
remove,
•
BEFORE
SKID
REMOVING
ATTACH STEERING
TRACTOR
ADAPTER--------SHAFT
FROM
WHEEL (See Fig. 1)
ASSEMBLE EXTENSION SHAFT AND BOOT
•
Slide extension shaft onto lower steering shaft,
•
Place tabs of steering boot over tab slots in dash and
push down to secure,
rAB
SLOTS
INSTALL STEERING WHEEL
•
Position front wheels of the tractor so they are pointing
straight forward.
•
Remove steering wheel adapter from steering wheel
and slide adapter onto steering shaft extension,
•
Position steering wheel so cross bars are horizontal
(left to right) and slide inside boot and onto adapter,
•
Assemble large flat washer, 5/16 lock washer, 5/16
hex bolt and tighten securely.
•
Snap steering wheel insert into center of steering
wheel,
FIG. 1
INSTALL SEAT (See Fig. 2)
Adjust seat before tightening adjustment bolt.
•
Remove adjustment bolt, lock washer and flat washer
securing seat to cardboard packing and set aside for
assembly of seat to tractor,
•
Pivot seat upward and remove from the cardboard packing, Remove the cardboard packing and discard,
•
Place seat on seat pan so head of shoulder bolt is
positioned over large slotted hole in pan,
•
Push down on seat to engage shoulder bolt in slot and
pull seat towards rear of tractor,
•
Pivot seat and pan forward and assemble adjustment bolt, Iockwasher and flat washer loosely, Do not
tighten
Lower seat into operating position and sit on seat,
•
Slide seat until a comfortable position is reached
which allows you to press clutch/brake pedal all the
way down,
•
Get off seat without moving its adjusted position,
•
Raise seat and tighten adjustment bolt securely,
•
Remove protective materials from tractor hood and
grill.
IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN
SKID THAT MAYPUNCTURETIRESWHERETRACTOR ISTO
ROLLOFF SKID.
6
ASSEMBLY
SEAT
SHOULDER
BOLT
TO ROLL TRACTOR OFF SKID (See Operation section for location and function of
controls)
•
•
•
•
•
Press lift lever plunger and raise attachment lift lever
to its highest position,
Release parking brake by depressing clutch/brake
pedal,
Place gearshift lever in neutral (N) position.
Roll tractor forward off skid,
Remove banding holding deflector shield up against
tractor,
TO DRIVE TRACTOR
OFF SKID (See Operation section for location and function
of
controls)
FLAT WASHER
LOCK WASHER_
ADJUSTMENT
BOLT
FIG. 2
CHECK BATTERY
(See Fig. 3)
•
Lift seat pan to raised position,
•
If this battery is put into service after month and year
indicated on label (label located between terminals)
charge battery for minimum of one hour at 6-10 amps,
(See "BATTERY" in MAINTENANCE section of this
manual for charging instructions),
_,WARNING: Before starting, read, understand and follow
all instructions in the Operation section of this manual, Be
sure tractor is in a well-ventilated area, Be sure the area in
front of tractor is clear of other people and objects,
•
Be sure all the above assembly steps have been completed.
•
Check engine oil level and fill fuel tank with gasoline,
•
Sit on seat in operating position, depress clutch/brake
pedal and set the parking brake,
•
Place gear shift lever in neutral (N) position,
•
Press lift lever plunger and raise attachment lift lever
to its highest position,
•
Start the engine.After engine has started, move throttle
control to idle position,
•
Depress clutch/brake pedal into full "BRAKE" position
and hold. Move gearshift lever to 1st gear.
•
Slowly release clutch/brake pedal and slowly drive
tractor off skid.
•
Apply brake to stop tractor, set parking brake and place
gearshift lever in neutral position.
•
Turn ignition key to "OFF" position.
Continue with the instructions that follow,
SEAT PAN
LABEL
FIG. 3
NOTE: You may now roll or drive your tractor off the skid,
Follow the appropriate instruction below to remove the
tractor from the skid.
ASSEMBLY
CHECK TIRE PRESSURE
,/CHECKL
IS T
The tires on your tractor were overinflated at the factory
for shipping purposes, Correct tire pressure is important
for best cutting performance,
•
Reduce tire pressure to PSI shown in "PRODUCT
SPECIFICATIONS" section of this manual,
BEFORE YOU OPERATE YOUR NEW TRACTOR, WE
WISH TO ASSURE THAT YOU RECEIVE THE BES T PERFORMANCEAND SATISFACTION FROM THIS QUALITY
PRODUCT.
CHECK DECK LEVELNESS
,/
,/
All assembly instructions have been completed.
No remaining loose parts in carton.
,/
Battery is properly prepared and charged. (Minimum
1 hour at 6 amps).
Seat is adjusted comfortably and tightened securely.
PLEASE REVIEW THE FOLLOWING CHECKLIST:
For best cutting results, mower housing should be properly
leveled, See "TO LEVEL MOWER HOUSING" in the Service
and Adjustments section of this manual.
CHECK
BELTS
FOR
PROPER
POSITION
,/
OF ALL
See the figures that are shown for replacing motion and
mower blade drive belts in the Service and Adjustments
section of this manual. Verify that the belts are routed
correctly,
,/
All tires are properly inflated. (For shipping purposes,
the tires were overinflated at the factory).
,/
Be sure mower deck is properly leveled side-to-side/
front-to-rear for best cutting results. (Tires must be
properly inflated for leveling).
,/
Check mower and drive belts. Be sure they are routed
properly around pulleys and inside all belt keepers.
Check wiring. See that all connections are still secure
and wires are properly clamped.
CHECK BRAKE SYSTEM
,/
After you learn how to ope rate your tractor, check to see that
the brake is properly adjusted, See "TO ADJUST BRAKE"
in the Service and Adjustments section of this manual,
,/
Before driving tractor, be sure freewheel control is in
"transmission engaged" position (see "TO TRANSPORT" in the Operation section of this manual).
WHILE LEARNING HOWTO USEYOURTRACTOR, PAY
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT
ITEMS:
,/
,/
,/
,/
,/
,/
8
Engine oil is at proper level.
Fuel tank is filled with fresh, clean, regular unleaded
gasoline.
Become familiar with all controls, their location and
function. Operate them before you start the engine.
Be sure brake system is in safe operating condition.
Be sure Operator Presence System and Reverse Operation System (ROS) are working properly (See the
Operation and Maintenance sections in this manual).
It is important to purge the transmission before operating your tractor for the first time. Follow proper starting and transmission purging instructions (See "TO
START ENGINE" and "PURGE TRANSMISSION" in
the Operation section of this manual).
OPERATION
These symbols may appear on your tractor or in literature supplied with the product, Learn and understand their meaning,
R
REVERSE
NEUTRAL
HIGH
LOW
SLOW
IGNITION SWITCH
ENGINE OFF
REVERSE
OPERATION
ENGINE
ON
ENGINE START
PARKING
BRAKE
PARKING BRAKE
LOCKED
PARKING BRAKE
UNLOCKED
SYSTEM (ROS)
Oi
OVER TEMP
LIGHT
FUEL
OIL PRESSURE
BATTERY
REVERSE
FORWARD
MOWER
HEIGHT
MOWER
LIFT
m
ATTACHMENT
CLUTCH DISENGAGED
ATTACHMENT
CLUTCH ENGAGED
LIGHTS ON
FREE WHEEL
(Automatic
Models only)
&
&
&
could result in serious injury or
death. The safety alert symbol
is used to identify safety information about hazards which can
result in death, serious injury
and/or property damage.
SLOPE HAZARDS
(SEE SAFETY
RULES SECTION)
DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.
WARNING
could
indicates
result
CAUTION
a hazard which, if not avoided,
in death
indicates
might result
CAUTION
Failure to follow instructions
KEEP AREA CLEAR
DANGER, KEEP HANDS
AND FEET AWAY
or serious
injury.
a hazard which,
in minor or moderate
when used without
the alert symbol,
indicates a situation that could
to the tractor and/or engine.
HOT SURFACES
indicates
if not avoided, could result
,_hl{$111Ntl,,
and/or property damage.
if not avoided,
injury.
result
in damage
a hazard which,
in death,
serious
FIRE indicates a hazard which, if not avoided,
could result in death, serious injury and/or
property
damage.
injury
OPERATION
KNOW
YOUR
TRACTOR
READ THIS OWNER'S
MANUAL AND SAFETY RULES BEFORE
OPERATING
YOUR TRACTOR
Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments,
Save this manual for future reference.
IGNITION
ATTACHMENT
CLUTCH LEVER
SWITCH
POSITION
THROTTL_
CHOKE
CONTROL
LIFTLEVER
PLUNGER
ATTACHMENT
LIFT LEVER
HEIGHT
ADJUSTMENT
INDICATOR
PARKING
BRAKE
GEAR SHIFT
LEVER
O2829
FIG. 4
Our tractors conform to the safety standards of the American National Standards Institute,
LIFT LEVER PLUNGER - Used to release attachment lift
lever when changing its position,
LIGHT SWITCH - Turns the headlights on and off,
PARKING BRAKE - Locks clutch/brake pedal into the
brake position,
REVERSE OPERATION SYSTEM (ROS) "ON" POSITION - Allows operation of mower deck or other powered
attachment while in reverse.
ATTACHMENT CLUTCH LEVER - Used to engage the
mower blades, or other attachments mounted to your
tractor.
ATTACHMENT LIFT LEVER - Used to raise, lower, and
adjust the mower deck or other attachments mounted to
your tractor.
CLUTCH/BRAKE PEDAL - Used for declutching and braking the tractor and starting the engine,
GEARSHIFT LEVER - Selects the speed and direction
of the tractor,
THROTTLE/CHOKE CONTROL - Used for starting and
controlling engine speed,
IGNITION SWITCH - Used for starting and stopping the
engine,
10
OPERATION
The operation of any tractor can result in foreign objects thrown into the eyes, which can result
in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or
performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles
or standard safety glasses.
HOW TO USE YOUR
TRACTOR
TO SET PARKING BRAKE (See Fig. 5)
Your tractor is equipped with an operator presence sensing switch. When engine is running, any attempt by the
operator to leave the seat without first setting the parking
brake will shut off the engine.
•
Depress clutch/brake pedal into full "BRAKE" position
and hold.
•
Place parking brake lever in "ENGAGED" position and
release pressure from clutch/brake pedal. Pedal should
remain in "BRAKE" position. Make sure parking brake
will hold tractor secure.
ATTACHMENT CLUTCH
LEVER "ENGAGED"
POSITION
T.°OTT'
CHOKE
CONTROL
\ "'_'L"-_
_
_ \ ',
\'._
POSITION
X'
_/"
TO USE THROTTLE
CONTROL
\ \\ _ _
PARKING BRAKE
_ _ _J"ENGAGED"
__
_
_"
(See Fig. 5)
Always operate engine at full throttle.
•
Operating engine at less than full throttle reduces the
battery charging rate.
•
Full throttle offers the best bagging and mower performance.
TO MOVE FORWARD AND BACKWARD
Fig. 5)
LEVER....L
;"
"BRAKE"
CAUTION: Always stop tractor completely, as described above, before leaving the operator's position; to empty
grass catcher, etc.
.O°.T.ON
._<_-_
_ /
_-_----_-_:,,Xf//"DISENGAGED"
"_
NOTE: Under certain conditions when tractor is standing
idle with the engine running, hot engine exhaust gases may
cause "browning" of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas.
POSITION
(See
The direction and speed of movement is controlled by the
gearshift lever.
•
Start tractor with clutch/brake pedal depressed and
gearshift lever in neutral (N) position.
•
Move gearshift lever to desired position.
•
Slowly release clutch/brake pedal to start movement.
IMPORTANT:
BRING TRACTOR
TO A COMPLETE
STOP
BEFORE
SHIFTING
OR CHANGING
GEARS.
FAILURE
CLUTCH/BRAKE
PEDAL "DRIVE"
POSITION
TO DO SO WILL SHORTEN THE USEFUL LIFE OF YOUR
TRANSAXLE.
PARKING BRAKE
"DISENGAGED"
POSITION
TO ADJUST
Fig. 5)
FIG.5
STOPPING
(See Fig. 5)
MOWER BLADES •
To stop mower blades, move attachment clutch lever
to "DISENGAGED" position.
GROUND DRIVE •
To stop ground drive, depress clutch/brake pedal into
full "BRAKE" position.
•
Move gearshift lever to neutral (N) position.
ENGINE •
Move throttle control between half and full speed (fast)
position.
NOTE: Failure to move throttle control between half and
full speed (fast) position, before stopping may cause engine
to "backfire".
•
Turn ignition key to "STOP" position and remove key.
Always remove key when leaving tractor to prevent
unauthorized use.
•
Never use choke to stop engine.
IMPORTANT:
LEAVING
THE
IGNITION
SWITCH
IN ANY
POSITION OTHERTHAN "OFF" WILL CAUSE THE BATTERY
TO BE DISCHARGED, (DEAD).
11
MOWER CUTTING
HEIGHT (See
The position of the attachment lift lever determines the
cutting height.
•
Grasp lift lever.
•
Press plunger with thumb and move lever to desired
position.
The cutting height range is approximately 1-1/2 to 4".
The heights are measured from the ground to the blade tip
with the engine not running. These heights are approximate
and may vary depending upon soil conditions, height of
grass and types of grass being mowed.
•
The average lawn should be cut to approximately 2-1/2
inches during the cool season and to over 3 inches
during hot months. For healthier and better looking
lawns, mow often and after moderate growth.
•
For best cutting performance, grass over 6 inches
in height should be mowed twice. Make the first cut
relatively high; the second to desired height.
OPERATION
TO OPERATE
MOWER (See Fig. 6)
Your tractor is equipped with an operator presence sensing switch, Any attempt by the operator to leave the seat
with the engine running and the attachment clutch engaged
will shut off the engine,You must remain fully and centrally
positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough,
rolling terrain or hills,
•
Select desired height of cut.
•
Start mower blades by engaging attachment clutch
control,
•
TO STOP MOWER BLADES - disengage attachment
clutch control,
_
without either the entire grass catcher,
on
mowers so
or the
deflector
CAUTION:
Doequipped,
not operate
the
mower
shield in place.
TO OPERATE
POSITION
LIFT LEVER
HIGH POSITION
•
•
•
LOW
POSITION
ATTACHMENT
CLUTCH LEVER
"DISENGAGED"
POSITION
ON HILLS
hills with slopes greater than 15 ° and
WARNING:
not any
driveslope,
up or down
do not drive Do
across
I_lb
•
"ENGAGED"
ENGINE "ON" POSITION
(NORMAL OPERATING)
ROS "ON" POSITION
Choose the slowest speed before starting up or down
hills,
Avoid stopping or changing speed on hills,
If slowing is necessary, move throttle control lever to
slower position,
If stopping is absolutely necessary, push clutch/brake
pedal quickly to brake position and engage parking
brake,
•
Move gearshift lever to 1st gear, Be sure you have
allowed room for tractor to roll slightly as you restart
movement,
•
To restart movement, slowly release parking brake and
clutch/brake pedal.
Make all turns slowly.
•
TO TRANSPORT
SHIELD
FIG. 6
REVERSE OPERATION SYSTEM (ROS)
Your tractor is equipped with a Reverse Operation System
(ROS). Any attempt by the operator to travel in the reverse
direction with the attachment clutch engaged will shut off
the engine unless ignition key is placed in the ROS "ON"
position,
A_,WARNING: Backing up with the attachment clutch engaged while mowing is strongly discouraged. Turning the
ROS "ON", to allow reverse operation with the attachment
clutch engaged, should only be done when the operator
decides it is necessary to reposition the machine with the
attachment engaged. Do not mow in reverse unless
absolutely necessary.
USING THE REVERSE OPERATION SYSTEM •
Depress clutch/brake pedal all the way down and
hold.
•
•
•
•
With engine running, turn ignition key counterclockwise
to ROS "ON" position.
Look down and behind before backing.
Move gear shift lever to reverse (R) position and slowly
release clutch/brake pedal to start movement,
When use of the ROS is no longer needed, turn the
ignition key clockwise to engine "ON" position,
12
•
•
•
Raise attachment lift to highest position with attachment
lift control,
When pushing or towing your tractor, be sure gearshift
lever is in neutral (N) position,
Do not push or tow tractor at more than five (5) MPH.
NOTE: To protect hood from damage when transporting
your tractor on a truck or a trailer, be sure hood is closed
and secured to tractor. Use an appropriate means of tying
hood to tractor (rope, cord, etc.),
TOWING
MENTS
CARTS
AND
OTHER
ATTACH-
Tow only the attachments that are recommended by and
comply with specifications of the manufacturer of your tractor, Use common sense when towing, Too heavy of a load,
while on a slope, is dangerous. Tires can lose traction with
the ground and cause you to lose control of your tractor,
OPERATION
BEFORE
STARTING
THE ENGINE
•
CHECK ENGINE OIL LEVEL
The engine in your tractor has been shipped, from the
factory, already filled with summer weight oil.
•
Check engine oil with tractor on level ground.
•
Remove oil fill cap/dipstick and wipe clean, reinsert the
dipstick and screw cap tight, wait for a few seconds,
remove and read oil level, If necessary, add oil until
"FULl" mark on dipstick is reached, Do not overfill.
•
For cold weather operation you should change oil for
easier starting (See "OIL VISCOSITY CHART" in the
Maintenance section of this manual).
•
To change engine oil, see the Maintenance section in
this manual,
WARM WEATHER STARTING (50 ° F and above)
•
When engine starts, move the throttle control to the
fast position,
•
The attachments and ground drive can now be used, If
the engine does not accept the load, restart the engine
and allow it to warm up for one minute using the choke
as described above,
COLD WEATHER STARTING ( 50 ° F and below)
•
When engine starts, allow engine to run with the throttle
control in the choke (1\1)position until the engine runs
roughly, then move throttle control to fast position, This
may require an engine warm-up period from several
seconds to several minutes, depending on the temperature,
•
The attachments can also be used during the engine
warm-up period,
ADD GASOLINE
•
Fill fuel tank to bottom of filler neck, Do not overfill,
Use fresh, clean, regular unleaded gasoline with a
minimum of 87 octane, (Use of leaded gasoline will
increase carbon and lead oxide deposits and reduce
valve life), Do not mix oil with gasoline, Purchase fuel
in quantities that can be used within 30 days to assure
fuel freshness,
I
I&
fuel. Do not store, spill or use gasoline
CAUTION:
Wipe
off any spilled oil or
near an open
flame,
Inse rt key into ignition and turn key clockwise to"START"
position and release key as soon as engine starts,
Do not run starter continuously for more than fifteen
seconds per minute, If the engine does not start after
several attempts, move throttle control to fast position,
wait a few minutes and try again. If engine still does
not start, move the throttle control back to the choke (
I\1) position and retry,
NOTE: If at a high altitude (above 3000 feet) or in cold
temperatures (below 32 F) the carburetor fuel mixture may
need to be adjusted for best engine performance. See "TO
ADJUST CARBURETOR" in the Service and Adjustments
section of this manual,
I
I
IMPORTANT:
WHEN
OPERATING
IN TEMPERATURES
BELOW32°F(0°C),
USE FRESH,
CLEAN
WINTER
GRADE
GASOLINE
TO HELP
INSURE
GOOD
COLD
WEATHER
STARTING.
CAUTION:
Alcohol blended fuels (called
gasohol or using ethanol or methanol) can attract moisture which leads to separation and
formation of acids during storage. Acidic gas
can damage the fuel system of an engine while
in storage. To avoid engine problems, the fuel
system should be emptied before storage of
30 days or longer. Drain the gas tank, start
the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel next
season. See Storage Instructions for additional
information. Never use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.
TO START ENGINE (See Fig. 5)
When starting the engine for the first time or if the engine
has run out of fuel, it will take extra cranking time to move
fuel from the tank to the engine.
•
Sit on seat in operating position, depress clutch/brake
pedal and set parking brake.
•
Place gear shift lever in neutral (N) position,
•
Move attachment clutch to "DISENGAGED" position.
•
Move throttle control to choke (1\1) position,
NOTE: Before starting, read the warm and cold starting
procedures below,
13
OPERATION
MOWING TIPS
•
•
•
•
Mower should be properly leveled for best mowing per
formance See TO LEVEL MOWER HOUSING in the
Service and Adjustments section of this manual
The left hand side of mower should be used for trim
ming
Drive so that clippings are discharged onto the area
that has been cut Have the cut area to the right of the
machine This will result in a more even distribution of
clippings and more uniform cutting
When mowing large areas start by turning to the right so
that clippings will discharge away from shrubs fences
driveways etc After one or two rounds mow in the
opposite direction making left hand turns until finished
(See Fig7)
f
•
•
•
r
=(
J
FIG. 7
14
If grass is extremely tall it should be mowed twice to
reduce load and possible fire hazard from dried clip
pings Make first cut relatively high; the second to the
desired height
Do not mow grass when it is wet Wet grass will plug
mower and leave undesirable clumps Allow grass to
dry before mowing
Always operate engine at full throttle when mowing to assure better mowing performance and proper
discharge of material Regulate ground speed by se
lecting a low enough gear to give the mower cutting
performance as well as the quality of cut desired
When operating attachments select a ground speed
that will suit the terrain and give best performance of
the attachment being used
MAINTENANCE
F,LL,N
OATES
REGULAR
VICE DATES
SERVICE
cChh:_ kkTB[;ekplOsPse[_;i° n
T
R
A
Check Operator
ROS Systems
Check
_V P
Presence
and
V _
for Loose
Fasteners
Sharpen/Replace
Mower
if
V's
Blades
C
Lubrication
0
Check
Battery
Level
1_4
Clean
Battery
and Terminals
if
R
Chart
V _
E
N
G
V-Belts
Check
Engine
V _
I_
Oil Level
li_
Change
Engine
Oil (with
Change
Engine
Oil (without
ll_
oil filter)
1_1,2
oil filter)
1_1,2
Clean Air
Filter
Vf2
Clean Air
Screen
V$2
Inspect
E
Replace
Clean
Muffler/Spark
Oil Filter
Engine
Spark
Replace
Air Filter
Replace
Fuel Filter
_1_
Arrester
(If equipped)
Cooling
Replace
1_1,2
Fins
li_
Plug
Paper
2
ll_
Cartridge
1 - Change
more often when operating
in high ambient
temperatures.
2 - Service
more often when operating
GENERAL
V _
v'
Check Transaxle Cooling
Check
V _
li_'s
under
a heavy
load
in dirty
or dusty
conditions.
3 - Replace
or
blades
more
often
4 - Not required
if equipped
5 - Tighten
front axle pivot
Do not overtighten.
RECOMMENDATIONS
when
mowing
in sandy
soil.
with maintenance-free
battery.
bolt to 35 ft.-Ibs,
maximum.
LUBRICATION
CHART
The warranty on this tractor does not cover items that have
been subjected to operator abuse or negligence. To receive
full value from the warranty, operator must maintain tractor
as instructed in this manual.
ZERK
@FRONT WHEEL
BEARING
Some adjustments will need to be made periodically to
properly maintain your tractor.
At least once a season, check to see if you should make
any of the adjustments described in the Service and
Adjustments section of this manual.
• At least once a year you should replace the spark
plug, clean or replace air filter, and check blades and
belts for wear. A new spark plug and clean air filter
assure proper air-fuel mixture and help your engine
run better and last longer.
BEFORE
•
•
•
•
•
@FRONT WHEEL
BEARING ZERK
I
EACH USE
I
Check engine oil level.
Check brake operation.
Check tire pressure.
Check operator presence and
ROS systems for proper operation.
Check for loose fasteners.
I
]
I
_--I
T--"
(])GEARSHIFT
PIVOTS
@SAE 30 OR 10W30 MOTOR OIL
@GENERAL
PURPOSE GREASE
@REFER TO MAINTENANCE
"ENGINE"
SECTION
IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS WHICH
HAVE SPECIAL NYLON BEARINGS. VISCOUS LUBRICANTS WILL
ATTRACT DUST AND DIRT THAT WILL SHORTEN THE LIFE OF
THE SELF-LUBRICATING BEARINGS.
IF YOU FEEL THEY MUST
BE LUBRICATED, USE ONLY A DRY, POWDERED GRAPHITE TYPE
LUBRICANT SPARINGLY.
15
MAINTENANCE
TRACTOR
BLADE CARE
Always observe safety rules when performing any maintenance.
For best results mower blades must be kept sharp. Replace
bent or damaged blades.
BRAKE OPERATION
CAUTION: Use only a replacement
blade approved by the manufacturer
of your tractor. Using a blade not approved by the manufacturer of your
tractor is hazardous, could damage
your tractor and void your warranty.
If tractor requires more than five (5) feet to stop at highest
speed in highest gear on a level, dry concrete or paved
surface, then brake must be checked and adjusted, (See
"TO ADJUST BRAKE" in the Service and Adjustments
section of this manual),
TIRES
•
Maintain proper air pressure in all tires (See "PRODUCT SPECIFICATIONS" section of this manual),
•
Keep tires free of gasoline, oil, or insect control
chemicals which can harm rubber.
•
Avoid stumps, stones, deep ruts, sharp objects and
other hazards that may cause tire damage,
NOTE: To seal tire punctures and prevent flat tires due
to slow leaks, tire sealant may be purchased from your
local parts dealer, Tire sealant also prevents tire dry rot
and corrosion,
BLADE REMOVAL (See Fig. 8)
•
•
•
Raise mower to highest position to allow access to
blades.
Remove blade bolt, lock washer and flat washer securing
blade.
Install new or resharpened blade with trailing edge up
towards deck as shown.
IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER
HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL
ASSEMBLY.
OPERATOR PRESENCE SYSTEM AND REVERSE
OPERATION SYSTEM (ROS)
•
Reassemble blade bolt, lock washer
in exact order as shown.
Be sure operator presence and reverse operation systems
are working properly, If your tractor does not function as
described, repair the problem immediately.
•
The engine should not start unless the brake pedal
is fully depressed, and the attachment clutch control
is in the disengaged position.
•
Tighten
CHECK OPERATOR PRESENCE SYSTEM
•
When the engine is running, any attempt by the
operator to leave the seat without first setting the
parking brake should shut off the engine,
•
When the engine is running and the attachment clutch
is engaged, any attempt by the operator to leave the
seat should shut off the engine,
•
The attachment clutch should never operate unless
the operator is in the seat,
CHECK REVERSE OPERATION (ROS) SYSTEM
•
When the engine is running with the ignition switch in
the engine "ON" position and the attachment clutch
engaged, any attempt by the operator to shift into
reverse should shut off the engine,
•
When the engine is running with the ignition switch
in the ROS "ON" position and the attachment clutch
engaged, any attempt by the operator to shift into
reverse should NOT shut off the engine.
ROS "ON" POSITION
ENGINE "ON" POSITION
(NORMAL OPERATING)
blade bolt securely
and flat washer
(27-35 Ft. Lbs. torque).
IMPORTANT: BLADE BOLT IS HEATTREATED.IF BOLT NEEDS
REPLACING, REPLACE ONLYWITH APPROVE BOLT SHOWN
IN THE REPAIR PARTS.
TRAILING
EDGE UP
MANDREL
ASSEMBLY
BLADE
CENTER
HOLE
FLAT WASHER
LOCK WASHER_
STAR
BOLT
FIG. 8
TO SHARPEN
BLADE (See Fig. 9)
NOTE: We do not recommend sharpening blade - but if
you do, be sure the blade is balanced,
Care should be taken to keep the blade balanced, An unbalanced blade will cause excessive vibration and eventual
damage to mower and engine,
•
The blade can be sharpened with a file or on a grinding wheel, Do not attempt to sharpen while on the
mowe r.
•
To check blade balance, you will need a 5/8" diameter
steel bolt, pin, or a cone balancer. (When using a
cone balancer, follow the instructions supplied with
balancer.)
NOTE: Do not use a nail for balancing blade. The lobes of
the center hole may appear to be centered, but are not.
•
Slide blade on to an unthreaded portion ofthe steel bolt
or pin and hold the bolt or pin parallel with the ground.
If blade is balanced, it should remain in a horizontal
position. If either end of the blade moves downward,
16
sharpen the heavy end until the blade is balanced.
MAINTENANCE
5,8"BO- T
OR PIN
""_
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, these multi-viscosity oils
will result in increased oil consumption when used above
32°E Check your engine oil level more frequently to avoid
possible engine damage from running low on oil,
B'AOE
Change the oil after every 25 hours of operation or at least
once a year if the tractor is not used for 25 hours in one
year.
_
FIG. 9
Check the crankcase oil level before starting the engine
and after each eight (8) hours of operation, Tighten oil fill
cap/dipstick securely each time you check the oil level,
BATTERY
Your tractor has a battery charging system which is sufficient
for normal use, However, periodic charging of the battery
with an automotive charger will extend its life.
•
Keep battery and terminals clean.
•
Keep battery bolts tight,
•
Keep small vent holes open.
•
Recharge at 6-10 amperes for 1 hour.
TO CHANGE ENGINE OIL (See Figs, 10 and 11)
Determine temperature range expected before oil change,
All oil must meet API service classification SG-SL
•
Be sure tractor is on level surface,
•
•
•
NOTE: The original equipment battery on your tractor is
maintenance free. Do not attempt to open or remove caps
or covers. Adding or checking level of electrolyte is not
necessary,
•
TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battery and terminals can cause
the battery to "leak" power,
•
Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor,
•
Rinse the battery with plain water and dry.
•
Clean terminals and battery cable ends with wire brush
until bright,
•
Coat terminals with grease or petroleum jelly.
•
Reinstall battery (See "REPLACING BATTERY" in the
Service and Adjustment section of this manual).
OIL DRAIN VALVE
V-BELTS
FIG. 11
CheckV-belts for deterioration and wearafter 100 hours and
replace if necessary. The belts are not adjustable. Replace
belts if they begin to slip from wear,
TRANSAXLE
•
•
•
COOLING
Keep transaxle free from build-up of dirt and chaff which
can restrict cooling,
•
ENGINE
•
LUBRICATION
Only use high quality detergent oil rated with API service
classification SG-SL, Select the oil's SAE viscosity grade
according to your expected operating temperature,
SAE VISCOSITY
-30
Oil will drain more freely when warm.
Catch oil in a suitable container,
Remove oil fill cap/dipstick, Be careful not to allow dirt
to enter the engine when changing oil,
Remove yellow cap from end of drain valve and install
the drain tube onto the fitting,
-20
TEMPERATURE
-10
RANGE
GRADES
0
ANTICIPATED
•
20
BEFORE
NEXT
30
40
OIL CHANGE
FIG. 10
17
Unlock drain valve by pushing inward and turning
counterclockwise,
To open, pull out on the drain valve,
After oil has drained completely, close and lock the
drain valve by pushing inward and turning clockwise
until the pin is in the locked position as shown,
Remove the drain tube and replace the cap onto to the
bottom fitting of the drain valve.
Refill engine with oil through oil fill dipstick tube, Pour
slowly. Do not overfill, For approximate capacity see
"PRODUCT SPECIFICATIONS" section of this manual.
Use gauge on oil fill cap/dipstick for checking level,
Be sure dipstick cap is tightened securely for accurate
reading. Keep oil at"FULU'line on dipstick.Tighten cap
onto the tube securely when finished,
MAINTENANCE
CLEAN AIR SCREEN
IN-LINE FUEL FILTER
Air screen must be kept free of dirt and chaff to prevent
engine damage from overheating, Clean with a wire brush
or compressed air to remove dirt and stubborn dried gum
fibers,
The fuel filter should be replaced once each season, If fuel
filter becomes clogged, obstructing fuel flow to carburetor,
replacement is required.
•
With engine cool, remove filter and plug fuel line sections.
•
Place new fuel filter in position in fuel line with arrow
pointing towards carburetor,
•
Be sure there are no fuel line leaks and clamps are
properly positioned.
•
Immediately wipe up any spilled gasoline,
AIR FILTER
Your engine will not run properly using a dirty air filter,
Service air cleaner more often under dusty conditions.
See Engine Manual.
MUFFLER
Inspect and replace corroded muffler and spark arrester
(if equipped) as it could create a fire hazard and/or damage.
(See Fig. 12)
CLAMP
CLAMP
SPARK PLUGS
Replace spark plugs at the beginning of each mowing season or after every 1O0 hours of use, whichever comes first,
Spark plug type and gap setting is shown in "PRODUCT
SPECIFICATIONS" section of this manual.
FUEL
FILTER
FIG. 12
CLEANING
•
Clean engine, battery, seat, finish, etc, of all foreign
matter,
•
Keep finished surfaces and wheels free of all gasoline,
oil, etc.
Protect painted surfaces with automotive type wax,
•
We do not recommend using a garden hose or pressure
washer to clean your tractor unless the engine and transmission are covered to keep water out,Water in engine or
transmission will shorten the useful life of your tractor, Use
compressed air or a leaf blower to remove grass, leaves
and trash from tractor and mower.
18
SERVICE
_
AND ADJUSTMENTS
MENTS:
ARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTDepress clutch/brake pedal fully and set parking brake.
Place gearshift lever in neutral (N) position.
•
Place attachment clutch in "DISENGAGED" position.
•
Turn ignition key to "STOP" and remove key.
•
Make sure the blades and all moving parts have completely stopped.
•
Disconnect spark plug wire from spark plug and place wire where it cannot come in contact
with plug.
IMPORTANT:
IF AN ATTACHMENT
OTHERTHAN
DECK IS TO BE MOUNTED ON THE TRACTOR,
FRONT LINKSAND HOOKTHECLUTCH
SPRING
HOLE IN FRAME.
TRACTOR
TO REMOVE
MOWER
(See
Fig. 13)
Mower will be easier to remove from the right side of tractor,
•
Place attachment clutch in "DISENGAGED" position,
•
Move attachment lift lever forward to lower mower to
its lowest position,
•
Roll belt off engine pulley.
•
Remove small retainer spring, and remove clutch spring
off pulley bolt.
•
Remove large retainer spring, slide collar off and push
housing guide out of bracket.
•
Disconnect anti-swaybar from chassis bracket by removing retainer spring,
•
Disconnect suspension arms from rear deck brackets
by removing retainer springs.
•
Disconnect front links from deck by removing retainer
springs,
•
Raise lift lever to raise suspension arms, Slide mower
out from under tractor,
THE MOWER
REMOVE THE
INTOSQUARE
TO INSTALL MOWER (See Fig. 13)
•
•
•
•
•
•
•
•
•
Raise attachment lift lever to its highest position.
Slide mower under tractor with deflector shield to right
side of tractor,
Lower lift lever to its lowest position.
Connect front links to mower deck and secure with
retainer springs,,
Connect suspension arms to rear deck brackets and
secure with retainer springs,
Connect anti-swaybar to chassis bracket and secure
with retainer spring,
Push clutch cable housing guide into bracket, slide collar onto guide and secure with large retainer spring.
Place flat washer and clutch spring on idler pulley bolt
and secure with small retainer spring.
Install belt onto engine pulley,
CLUTCH SPRING,
FLAT
SMALL RETAINER SPRING
CLUTCH SPRING
FRONT LINK
RETAINER
RETAINER SPRINGS
(BOTH SIDES)
HOUSING GUIDE
RETAINER
SPRING
BRACKET
DEFLECTOR
FIG. 13
19
SHIELD
SERVICE
AND ADJUSTMENTS
When distance 'D is 1/8" to 1/2 lower at front than
rear tighten nuts 'F against trunnion on both front
links
TO LEVEL MOWER HOUSING
Adjust the mower while tractor is parked on level ground
or driveway Make sure tires are properly inflated (See
"PRODUCT SPECIFICATIONS section of this manual) If
tires are over or underinflated you will not properly adjust
your mower
SIDETOSIDE ADJUSTMENT (See Figs 14 and 15)
•
Raise mower to its highest position
•
At the midpoint of both sides of mower measure height
from bottom edge of mower to ground
Distance "A
on both sides of mower should be the same or within
1/4 of each other
•
•
•
•
•
•
To raise front of mower, loosen nut 'F from trunnion on
both front links Tighten nut "E on both front links an
equal number of turnsThe two front links must remain
equal in length
Whendistance"Disl/8tol/21oweratfrontthanrear,
tighten nut 'F against trunnion on both front links
Recheck sidetoside adjustment
MANDREL
If adjustment is necessary make adjustment on one
side of mower only
To raise one side of mower, tighten lift link adjustment
nut on that side
To lower one side of mower loosen lift link adjustment
nut on that side
FIG. 16
NOTE: Each full turn of adjustment nut will change mower
height about 1/8
•
Recheck measurements after adjusting
BOTTOM EDGE
OF MOWER TO
GROUND
BOTH FRONT LINKS MUST BE EQUAL IN LENGTH
BOTTOM EDGE
OF MOWER TO
__/
GROUND
NUT "E"
FIG. 14
SUSPENSION
TRUNNION
ARM
FRONT LINKS
LIFT LINK
FIG. 17
TO REPLACE
FIG. 15
FRONTTOBACK
ADJUSTMENT
(See Figs
16 and
MOWER
BLADE DRIVE BELT
(See Fig. 18)
17)
The mower blade drive belt may be replaced without tools
Park the tractor on level surface Engage parking brake
BELT REMOVAL
•
Remove mower from tractor (See 'TO REMOVE
MOWER in this section of this manual)
•
Work belt off both mandrel pulleys and idler pulleys
•
Pull belt away from mower
BELT INSTALLATION
•
Install new belt in reverse order of removal
•
Make sure belt is in all pulley grooves and inside all
belt guides
•
Install mower in reverse order of removal instruc
tions
IMPORTANT:
DECK MUST BE LEVEL SIDETOSIDE
IF THE
FOLLOWING FRONT TO BACKADJUSTMENT
IS NECESSARY
BE SURE TO ADJUST
BOTH FRONT LINKS
EQUALLY
SO
MOWER WILL STAY LEVEL SIDETOSIDE
To obtain the best cutting results the mower housing
should be adjusted so that the front is approximately 1/8
to 1/2 lower than the rear when the mower is in its high
est position
Check adjustment on right side of tractor Measu re distance
"D directly in front and behind the mandrel at bottom edge
of mower housing as shown
•
Before making any necessary adjustments, check that
both front links are equal in length
•
If links are not equal in length adjust one link to same
length as other link
•
To lower front of mower loosen nut "E on both front
links an equal number of turns
20
SERVICE
AND ADJUSTMENTS
TO REPLACE
IDLER PULLEYS
MOTION
DRIVE BELT
(See Fig. 20)
Park the tractor on level surface, Engage parking brake,
For assistance, there is a belt installation guide decal on
bottom side of left footrest,
BELT REMOVAL •
Remove mower (See "TO REMOVE MOWER" in this
section of manual),
NOTE: Observe entire motion drive belt and position of all
belt guides and keepers,
•
Remove belt from stationary idler and clutching idler,
•
Remove belt downward from around engine pulley,
•
Pull belt slack toward rear of tractor, Remove belt
upwards from transaxle pulley by deflecting belt keepers.
•
Remove belt from center span keeper and pull belt
away from tractor.
MANDREL PULLEYS
FIG. 18
TO CHECK
AND ADJUST
BRAKE
(See Fig.
19)
Your tractor is equipped with an adjustable brake system
which is mounted on the right side of the transaxle,
BELT INSTALLATION •
Carefully work new belt down between transaxle belt
keepers and onto the input pulley.
•
Slide belt into the center span keeper,
•
Pull belt toward front of tractor and roll around the top
groove of engine pulley.
•
Install belt through stationary idler and clutching
idler,
If tractor requires more than five (5) feet to stop at highest
speed in highest gear on a level, dry concrete or paved
surface, then brake must be checked and adjusted.
TO CHECK BRAKE
•
Park tractoron a level, dry concrete or paved surface,
depress clutch/brake pedal all the way down and engage parking brake.
•
Place gear shift lever in neutral (N) position,
•
•
The rear wheel s must lock and skid when you try to manually
push the tractor forward, If the rear wheels rotate, the brake
needs to be adjusted or the pads need to be replaced.
TO ADJUST BRAKE
•
Depress clutch/brake pedal all the way down and engage parking brake,
•
Measure distance between brake operating arm and
nut "A" on brake rod,
•
If distance is other than 1-1/2", loosen jam nut and turn
nut "A" until distance becomes 1-1/2". Retighten jam
nut against nut "A".
•
Road test tractor for proper stopping distance as stated
above, Readjust if necessary. If stopping distance is
still greater than five (5) feet in highest gear, further
maintenance is necessary. Replace brake pads or
contact a qualified service center,
Make sure belt is in all pulley grooves and inside all
belt guides and keepers,
Install mower (See "TO INSTALL MOWER" in this section of manual).
PULLEY
CLUTCHING
IDLER
IDLER
CENTER SPAN _
KEEPER
PULLEY
WITH PARKING BRAKE "ENGAGED"
1-1/2"
FIG. 20
TRANSAXLE
NUT "A"
JAM NUT
__ATING
FIG. 19
ARM
21
GEAR SHIFT LEVER NEUTRAL-
ADJUSTMENT
(See Fig. 21)
The transaxle should be in neutral when the gear shift
lever is in neutral (N) (lock gate) position, The adjustment
is preset at the factory; however, if adjustment is needed,
proceed as follows:
•
Make sure transaxle is in neutral (N).
NOTE: When the tractor rear wheels move freely, the
transaxle is in neutral.
SERVICE
AND ADJUSTMENTS
TO START ENGINE WITHAWEAK
'See Fig. 23)
•
Loosen adjustment bolt in front of the right rear
wheel,
•
Position the gear shift lever in the neutral (N) position,
•
Tighten adjustment bolt securely,
NOTE: If additional clearance is needed to getto adjustment
bolt, move mower deck height to the lowest position,
GEARSHIFT
erate explosive gases. Keep sparks,
flame
and smoking
materials
away from
WARNING:
Lead-acid
batteries
genbatteries. Always wear eye protection
when around batteries.
NEUTRAL
LOCK GATE
LEVER
If your battery is too weak to start the engine, it should be
recharged, (See "BATTERY" in the Maintenance section
of this manual),
If "jumper cables" are used for emergency starting, follow
this procedure:
IMPORTANT:YOURTRACTORIS EQUIPPEDWITH A 12 VOLT
SYSTEM.THE OTHER VEHICLE MUST ALSO BE A 12 VOLT
SYSTEM.DO NOT USEYOURTRACTORBATTERYTO START
OTHERVEHICLES.
ADJUSTMENT
BOLT
TO ATTACH JUMPER CABLES •
Connect one end of the RED cable to the POSITIVE
(+) terminal of each battery(A-B), taking care not to
short against tractor chassis,
•
Connect one end of the BLACKcable tothe NEGATIVE
(-) terminal (C) of fully charged battery,
•
Connect the other end of the BLACK cable (D) to good
chassis ground, away from fuel tank and battery,
FIG. 21
TO ADJUST
MENT
STEERING
WHEEL
BATTERY
ALIGN-
If steering wheel crossbars are not horizontal (left to right)
when wheels are positioned straight forward, remove steering wheel and reassemble per instructions in the Assembly
section of this manual,
TO REMOVE CABLES, REVERSE ORDER •
BLACK cable first from chassis and then from the fully
charged battery.
•
RED cable last from both batteries.
FRONT WHEEL TOE-IN/CAMBER
The front wheel toe-in and camber are not adjustable on
your tractor, If damage has occurred to affect the front wheel
toe-in or camber, contact your nearest authorized service
center/department,
TO REMOVE WHEEL FOR REPAIRS
(See Fig. 22)
•
•
•
•
•
•
Block up axle securely.
Remove axle cover, retaining ring and washers to allow
wheel removal (rear wheel contains a square key - Do
not lose).
Repair tire and reassemble.
On rear wheels only: align grooves in rear wheel hub
and axle, Insert square key.
Replace washers and snap retaining ring securely in
axle groove,
Replace axle cover.
WEAK OR DEAD
BATTERY
FIG. 23
REPLACING
NOTE: To seal tire punctures and prevent flat tires due to
slow leaks, tire sealant may be purchased from your local
parts dealer. Tire sealant also prevents tire dry rot and
&
corrosion.
RETAINING
RING
FULLY CHARGED
BATTERY
WASHERS
BATTERY (See
Figs. 24 and 25'
WARNING: Do not short battery
terminals by allowing a wrench or any
other object to contact both terminals
at the same time. Before connecting battery, remove metal bracelets,
wristwatch bands, rings, etc.
Positive terminal must be connected
first to prevent sparking from accidental grounding.
AXLE\
•
•
COVERXx@
SQUARE KEY(REARWHEELONLY)
•
FIG. 22
22
Lift seat pan to raised position.
Disconnect BLACK battery cable first then RED battery
cable and carefully remove battery from tractor.
Install new battery with terminals in same position as
old battery.
SERVICE
AND ADJUSTMENTS
First connect RED battery cable to positive (+) terminal
with hex bolt and keps nut as shown,Tighten securely.
Slide terminal cover over terminal,
HOOD
Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten
securely.
g ,c .gW,RE
SEAT PAN
®
FIG. 26
FIG. 24
TERMINAL
ENGINE
KEPS NUT
COVER
TO ADJUST THROTTLE
"'_"_.
HEX
BOLT
CONTROL
CABLE
The throttle control has been preset at the factory and
adjustment should not be necessary. If adjustment is necessary, see engine manual,
TO ADJUST CHOKE CONTROL
POSITIVE (RED) CABLE
The choke control has been preset at the factory and adjustment should not be necessary, If adjustment is necessary, see engne manual,
NEGATIVE (BLACK) CABLE
FIG. 25
TO REPLACE
•
•
•
•
HEADLIGHT
BULB
TO ADJUST CARBURETOR
Raise hood,
Pull bulb holder out of the hole in the backside of the
grill.
Replace bulb in holder and push bulb holder securely
back into the hole in the backside of the grill,
Close hood,
INTERLOCKS
Your carburetor is not adjustable, If your engine does not
operate properly due to suspected carburetor problems,
take your tractor to an authorized service center for repair
and/or adjustment,
AND RELAYS
Loose or damaged wiring may cause your tractor to run
poorly, stop running, or prevent it from starting,
•
Check wiring, See electrical wiring diagram in the
Repair Parts section,
TO REPLACE
FUSE
Replace with 20 amp automotive-type plug-in fuse. The
fuse holder is located behind the dash.
TO REMOVE
HOOD AND GRILL ASSEMBLY
(See Fig. 26)
•
Raise hood,
•
•
•
Unsnap headlight wire connector.
Stand in front of tractor. Grasp hood at sides, tilt toward
engine and lift off of tractor,
To replace, reverse above procedure,
23
STORAGE
ENGINE
Immediately prepare your tractor for storage at the end
of the season or if the tractor will not be used for 30 days
or more.
FUEL SYSTEM
IMPORTANT:
IT IS IMPORTANTTO
PREVENT GUM DEPOSITS
FROM FORMING IN ESSENTIAL
FUEL SYSTEM PARTS SUCH
AS CARBURETOR,
FUEL FILTER, FUEL HOSE, OR TANK
DURING STORAGE.
ALSO, EXPERIENCE
INDICATES
THAT
ALCOHOL
BLENDED FUELS (CALLED GASOHOL
OR USING
WARNING: Never store the tractor with
gasoline in the tank inside a building
where fumes may reach an open flame
or spark. Allow the engine to cool before
storing in any enclosure.
ETHANOLOR METHANOL)CANATTRACTMOISTUREWHICH
LEADSTOSEPARATIONAND FORMATIONOFACIDS DURING
STORAGE. ACIDIC GAS CAN DAMAGETHE FUEL SYSTEM
OF AN ENGINEWHILE IN STORAGE.
•
Empty the fuel tank by starting the engine and let it run
until the fuel lines and carburetor are empty.
•
Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur,
•
Use fresh fuel next season,
TRACTOR
Remove mower from tractor for winter storage. When mower
isto be stored for a period of time, clean it thoroughly, remove
all dirt, grease, leaves, etc. Store in a clean, dry area,
•
Clean entire tractor (See "CLEANING" in the Maintenance section of this manual),
•
Inspect and replace belts, if necessary (See belt replacement instructions in the Service and Adjustments
section of this manual),
•
Lubricate as shown in the Maintenance section of this
manual.
•
•
NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage,
Add stabilizer to gasoline in fuel tank or storage container,
Always follow the mix ratio found on stabilizer container,
Run engine at least 10 minutes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not empty
the gas tank and carburetor if using fuel stabilizer,
Be sure that all nuts, bolts and screws are securely
fastened, Inspect moving parts for damage, breakage
and wear, Replace if necessary.
Touch up all rusted or chipped paint surfaces; sand
lightly before painting,
ENGINE OIL
Drain oil (with engine warm) and replace with clean engine oil, (See "ENGINE" in the Maintenance section of
this manual),
BATTERY
•
•
•
•
•
CYLINDER(S)
Fully charge the battery for storage.
After a period of time in storage, battery may require
recharging.
To help prevent corrosion and power leakage during
long periods of storage, battery cables should be disconnected and battery cleaned thoroughly (see "TO
CLEAN BATTERY AND TERMINALS" in the Maintenance section of this manual).
After cleaning, leave cables disconnected and place
cables where they cannot come in contact with battery
terminals,
If battery is removed from tractor for storage, do not
store battery directly on concrete or damp surfaces,
•
•
•
•
Remove spark plug(s).
Pour one ounce of oil through spark plug hole(s) into
cylinder(s),
Turn ignition key to "START" position for a few seconds
to distribute oil,
Replace with new spark plug(s),
OTHER
•
•
•
•
Do not store gasoline from one season to another,
Replace your gasoline can if your can starts to rust,
Rust and/or dirt in your gasoline will cause problems.
If possible, store your tractor indoors and cover it to
give protection from dust and dirt.
Cover your tractor with a suitable protective cover that
does not retain moisture. Do not use plastic, Plastic
cannot breathe which allows condensation to form and
will cause your tractor to rust.
IMPORTANT:
NEVERCOVERTRACTORWHILE
EXHAUST AREAS ARE STILL WARM.
24
ENGINE
AND
TROUBLESHOOTING
PROBLEM
Will not start
CAUSE
CORRECTION
1.
Out of fuel.
1.
Fill fuel tank.
2.
3.
4.
5.
6.
7.
Engine not "CHOKED" properly.
Engine flooded.
Bad spark plug.
Dirty air filter.
Dirty fuel filter.
Water in fuel.
2.
3.
4.
5.
6.
7.
8.
9.
Loose or damaged wiring.
Carburetor out of adjustment.
8.
9.
See "TO START ENGINE" in Operation section.
Wait several minutes before attempting to start.
Replace spark plug.
Clean/replace air filter.
Replace fuel filter.
Empty fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter.
Check all wiring.
See "To Adjust Carburetor" in Service Adjustments
section.
10.
Hard to start
POINTS
Engine valves out of adjustment.
10.
Contact an authorized service center/department.
1.
2.
3.
4.
5.
6.
7.
Dirty air filter.
Bad spark plug.
Weak or dead battery.
Dirty fuel filter.
Stale or dirty fuel.
Loose or damaged wiring.
Carburetor out of adjustment.
1.
2.
3.
4.
5.
6.
7.
Clean/replace air filter.
Replace spark plug.
Recharge or replace battery.
Replace fuel filter.
Empty fuel tank and refill tank with fresh, clean gasoline.
Check all wiring.
See "To Adjust Carburetor" in Service Adjustments
section.
8.
Engine valves out of adjustment.
8.
Contact an authorized service center/department.
Engine will not turn over
1.
2.
3.
4.
5.
6.
7.
8.
9.
Clutch/brake pedal not depressed.
Attachment clutch is engaged.
Weak or dead battery.
Blown fuse.
Corroded battery terminals.
Loose or damaged wiring.
Faulty ignition switch.
Faulty solenoid or starter.
Faulty operator presence switch(es).
1.
2.
3.
4.
5.
6.
7.
8.
9.
Depress clutch/brake pedal.
Disengage attachment clutch.
Recharge or replace battery.
Replace fuse.
Clean battery terminals.
Check all wiring.
ChecWreplace ignition switch.
ChecWreplace solenoid or starter.
Contact an authorized service center/department.
Engine clicks but will not
start
1.
2.
3.
4.
Weak or dead battery.
Corroded battery terminals.
Loose or damaged wiring.
Faulty solenoid or starter.
1.
2.
3.
4.
Recharge or replace battery.
Clean battery terminals.
Check all wiring.
ChecWreplace solenoid or starter.
Loss of power
1.
2.
Cutting too much grass/too fast.
Throttle in 'CHOKE" position.
Build-up of grass, leaves and trash under mower.
Dirty air filter.
Low oil level/dirty oil.
Faulty spark plug.
Dirty fuel filter.
Stale or dirty fuel.
Water in fuel.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Raise cutting height/reduce speed.
Adjust throttle control.
Clean underside of mower housing.
Clean/replace air filter.
Check oil level/change oil.
Clean and regap or change spark plug.
Replace fuel filter.
Empty fuel tank and refill tank with fresh, clean gasoline.
Empty fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter.
Connect and tighten spark plug wire.
Clean engine air screen/fins.
Clean/replace muffler.
Check allwiring.
See "To Adjust Carburetor" in Service Adjustments
section.
3.
4.
5.
6.
7.
8.
9.
Excessive vibration
10.
11.
12.
13.
14.
Spark plug wire loose.
Dirty engine air screen/fins.
Dirty/clogged muffler.
Loose or damaged wiring.
Carburetor out of adjustment.
10.
11.
12.
13.
14.
15.
Engine valves out of adjustment.
15.
1.
2.
Worn, bent or loose blade.
Bent blade mandrel.
3.
Loose/damaged part(s).
1.
2.
3.
25
Contact an authorized service center/department.
Replace blade. Tighten blade bolt.
Replace blade mandrel.
Tighten loose part(s). Replace damaged parts.
TROUBLESHOOTING
POINTS
PROBLEM
CAUSE
CORRECTION
Engine dies when
tractor is shifted
into reverse
1.
1.
Turn ignition key to
ROS "ON" position.
See Operation section.
Engine continues to run
when operator leaves seat
with attachment clutch
Reverse operation system
(ROS) is not "ON" while
mower or other attachment
is engaged.
1.
Faulty operator-safety presence control system.
1.
Check wiring, switches and connections. If not
corrected, contact an authorized service center/
department.
1.
2.
Worn, bent or loose blade.
Mower deck not level.
1.
2.
Replace blade. Tighten blade bolt.
Level mower deck.
3.
4.
5.
Buildup of grass, leaves, and trash under mower.
Bent blade mandrel.
Clogged mower deck vent holes from buildup of
grass, leaves, and trash around mandrels.
3.
4.
5.
Clean underside of mower housing.
Replace blade mandrel.
Clean around mandrels to open vent holes.
engaged
Poorcut-uneven
Mower blades will not
rotate
Poor grass discharge
1.
Obstruction in clutch mechanism.
1.
Remove obstruction.
2.
3.
4.
Worn/damaged mower drive belt.
Frozen idler pulley.
Frozen blade mandrel.
2.
3.
4.
Replace mower drive belt.
Replace idler pulley.
Replace blade mandrel.
1.
2.
3.
4.
Engine speed too slow.
Travel speed too fast.
Wet grass.
Mower deck not level.
1.
2.
3.
4.
Place throttle control in "FAST" position.
Shift to slower speed.
Allow grass to dry before mowing.
Level mower deck.
5.
6.
7.
8.
Low/uneven tire air pressure.
Worn, bent or loose blade.
Buildup of grass, leaves and trash under mower.
Mower drive belt worn.
9.
10.
1.
Blades improperly installed.
Improper blades used.
Clogged mower deck vent holes from buildup of
grass, leaves, and trash around mandrels.
5.
6.
7.
8.
9.
10.
11.
Check tires for proper air pressure.
Replace/sharpen blade. Tighten blade bolt.
Clean underside of mower housing.
Replace mower drive belt.
Reinstall blades sharp edge down.
Replace with blades listed in this manual.
Clean around mandrels to open vent holes.
Headlight(s) not working
(if so equipped)
1.
2.
3.
4.
5.
Light switch is "OFF".
Bulb(s) or lamp(s) burned out.
Faulty light switch.
Loose or damaged wiring.
Blown fuse.
1.
2.
3.
4.
5.
Turn light switch "ON".
Replace bulb(s) or lamp(s).
Check/replace light switch.
Check wiring and connections.
Replace fuse.
Battery will not charge
1.
2.
3.
4.
Bad battery cell(s).
Poor cable connections.
Faulty regulator (if so equipped).
Faulty alternator.
1.
2.
3.
4.
Replace battery.
Check/clean all connections.
Replace regulator.
Replace alternator.
Engine "backfires" when
turning engine "OFF"
1.
Engine throttle control not set between half and
full speed (fast) position before stopping engine.
1.
Move throttle control between half and full speed
(fast) position before stopping engine.
26
LIMITED WARRANTY
The Manufacturer
warrants to the original consumer purchaser that this product as manufactured
is free from defects in materials and workmanship.
For a period of two (2) years from date of purchase by the original consumer
purchaser, we will repair or
replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we find to be defective due
to materials
or workmanship.
This Warranty
is subject
to the following
limitations
and exclusions.
1.
This warranty does not apply to the engine, other than EHP manufactured
transaxle/transmission
cept as noted below) or components
parts thereof. Please refer to the applicable manufacturer's
2.
Transportation
charges for the movement
of any power equipment
unit or attachment
are the responsibility
of the purchaser. Transportation
charges for any parts submitted for replacement
under this warranty must be paid by the purchaser
unless such return is requested by Electrolux Home Products.
3.
Battery Warranty:
On products equipped with a Battery, we will replace, without charge to you, any battery which we find
to be defective in manufacture,
during the first ninety (90) days of ownership. After ninety (90) days, we will exchange
the
Battery, charging you 1/12 of the price of a new Battery for each full month from the date of the original sale. Battery must
be maintained
in accordance
with the instructions furnished.
4.
The Warranty
purchase.
5.
This Warranty applies only to products which have been properly assembled,
adjusted, operated, and maintained
in accordance with the instructions
furnished. This Warranty does not apply to any product which has been subjected to alteration,
misuse, abuse, improper assembly or installation,
delivery damage, or to normal wear of the product.
6.
Exclusions:
Excluded
hardware and normal
7.
In the event you have a claim
Should
period
for any products
from this Warranty
maintenance.
you have any unanswered
Electrolux
Outdoor
Home
Products
are belts,
under this Warranty,
questions
Products,
blades,
blade adapters,
this Warranty,
Inc.
Service
is limited
normal
you must return the product
concerning
Customer
purposes
Dept.
please
to 90 days from the date of original
wear, normal
to an authorized
adjustments,
service
standard
dealer.
contact:
In Canada
contact:
Electrolux
Canada
Creek
Road
7075 Ordan
GA 30907
USA
Mississauga,
1030 Stevens
Augusta,
used for rental or commercial
components,
battery (exwarranty on these items.
Corp.
Drive
Ontario
L5T 1K6
giving the model number, serial number
dealer from whom it was purchased.
and date of purchase
of your product
and the name
and address
of the authorized
THIS WARRANTY
DOES NOT APPLY TO INCIDENTAL
OR CONSEQUENTIAL
DAMAGES
AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED
WARRANTIES.
Some areas
do not allow the limitation of consequential
damages or limitations
of how long an implied Warranty may last, so the above limitations or exclusions
may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which
vary from locale to locale.
This is a limited
Warranty
within
the meaning
of that term as defined
27
in the Magnuson-Moss
Act of 1975.
SERVICE
POLICY
WARRANTY
TECUMSE_
TECUMSE_
Issued January 1980
Revised January 1991
LIMITED WARRANTIES
FOR
NEW PEERLESS GEAR POWER TRAIN COMPONENTS
A.
Products
Warranted
Peerless Gear and Machine Division of Tecumseh
Products Company ("Tecumseh"),
subject to the limitations contained
below,
will,at its option, repair or replace, without charge for parts or labor only, any part of a new Power Train Component
(which as used
herein means and includes the transaxle,
gear box, transmission,
differential
and right angle drives, and any part of the Power Train
Component),
EXCEPT any new Power Train Component
incorporated
in equipment
used for commercial
or rental purposes, which is
found upon examination
by any Tecumseh Authorized
Service Outlet or by Tecumseh's factory in Grafton, Wisconsin,
to be DEFECTIVE
IN MATERIAL AND/OR WORKMANSHIP
if received by Tecumseh or a Tecumseh Authorized
Service Outlet for such examination
within
TWO YEARS from the date of sale to the original consumer
purchaser of Peerless Series 820, 900, 910, 915, 920, 930 transaxles
and
Series 1100 angle drive and ONE YEAR for all other Peerless products.
New Power Train Components
incorporated
in equipment used
for commercial
purposes are warranted
in the same manner and to the same extent EXCEPT such Power Train Components
are warranted for NINETY (90) DAYS ONLY, and must be received by Tecumseh or by a Tecumseh Authorized
Service Outlet for such examination within 90 days from the date of sale to the original purchaser.
New Power Train Components
Incorporated
in equipment
used for
rental purposes are warranted
in the same manner and to the same extent EXCEPT such Power Train Components
are warranted for
THIRTY (30) DAYS ONLY, and must be received by Tecumseh or a Tecumseh Authorized
Service Outlet within 30 days from the date
of sale to the original purchaser.
B.
Products
And
Items
Not Warranted
1.
2.
Alterations
or Modifications
of Power Train Components.
Accidents,
Normal Maintenance,
Failure to follow the Original Equipment
Manufacturer's
Manual.
This warranty covers only parts of new Power Train Components
which are found upon examination
to be defective in material or
workmanship
as delivered to the original purchaser.
This warranty does not cover defects caused by depreciation
or damage caused
by normal wear, accidents, improper maintenance,
improper use or abuse of the product, failure to follow the instructions
contained in
an Instruction
Manual for the operation of the Power Train Component
and parts. The cost of normal maintenance
and replacement
of
service items which are not defective shall be paid for by the original purchaser.
C. Securinq
Warranty
Service
Warranty service can be arranged for by contacting either a Tecumseh Authorized
Service Outlet (any Tecumseh Registered Service
Dealer, Tecumseh Authorized
Service Distributor, or Tecumseh Central Warehouse
Distributor)
or by contacting Tecumseh, c/o Service
Manager, Engine and Transmission
Group Service Division, 900 North Street, Grafton, Wisconsin
53024. Warranty service can only
be performed
by a Tecumseh Authorized
Service Outlet or by Tecumseh at its factory in Grafton, Wisconsin.
At the time of requesting
warranty service, evidence must be presented
of the date of sale to the original purchaser.
The purchaser
shall pay any charges for
making service calls and/or for transporting
the product to and from the place where the inspection and/or warranty work is performed.
The purchaser shall be responsible
for any damage or loss incurred in connection with the transportation
of Power Train Components
and/or part(s) of the Power Train Components
submitted for inspection and/or warranty work.
D. Limitation
of Damaqes
and Implied
Warranties
The foregoing EXPRESSED
WARRANTY
IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES.
Neither Tecumseh nor any of its
affiliates makes any warranties,
representations
or promises, written or oral, as to the quality of the Power Train Component
or any of
its parts, other than as set forth herein.
ANY IMPLIED WARRANTY
OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR
PURPOSE,
TO THE EXTENT THAT
EITHER MAY APPLY TO ANY PART(S) OF POWER TRAIN COMPONENTS,
SHALL BE LIMITED IN DURATION TO THE PERIODS
OFTHE EXPRESSED
WARRANTIES
DEFINED IN PARAGRAPH
A HEREOE
IN NO EVENTWILLTECUMSEH
BE LIABLE FOR ANY
INCIDENTAL,
CONSEQUENTIAL
OR SPECIAL DAMAGES
AND/OR EXPENSES.
Some states do not allow limitations
on how long
an implied warranty lasts or the exclusion or limitation of incidental or consequential
damages, so the above limitation(s)
or exclusion(s)
may not apply to you. This warranty gives you specific legal rights and you may also have other legal rights which vary from state to
state.
E. No Dealer
Warranty
Tecumseh neither assumes nor authorizes
any other person, natural or corporate, to assume for Tecumseh any other obligations or
liabilities in connection with or with respect to any part(s) of a Power Train Component.
The seller or dealer of part(s) of a Power Train
Component
has no authority, whatsoever,
to make any representations
or promises on behalf of Tecumseh or to modify the terms or
limitations of Tecumseh's warranty in any way.
28
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION
ONLY RIDE UP AND DOWN HILL,
NOT ACROSS HILL
_O
15 DEGREES
_b
MAX.
down the face of slopes, never across the face. Do not mow
ARNING: To avoid serious injury, operate your tractor up and
slopes greater than 15 degrees. Make turns gradually to prevent
tipping or loss of control. Exercise extreme caution when
changing direction on slopes.
1. Fold this page along dotted line indicated above.
2. Hold page before you so that its left edge is vertically parallel to a tree
trunk or other upright structure.
3. Sight across the fold in the direction of hill slope you want to measure.
4. Compare the angle of the fold with the slope of the hill.
PARTS AND SERVICE
This product has been expertly engineered and carefully manufactured to rigid quality standards. As with all
mechanical products, some adjustments or part replacement may be necessary during the life of your unit.
For Parts and service, contact our authorized distributor: call 1-800-849-1297
•
For replacement parts, have available the following information:
a.
Model Number/Manufacturer's
b.
Description of part.
I.D. Number
For Techical Assistance: call 1-800-829-5886
For a Parts Manual, go to our website: www.poulan-pro.com/support.asp
NOTE:
Electrolux Home Products provides parts and service through its authorized distributors and
dealers; therefore, all requests for parts and service should be directed to your local dealer(s).
The philosophy of Electrolux Home Products is to continually improve all of its products. If
the operating characteristics or the appearance of your product differs from those described
in this Manual, please contact your local dealer for updated information and assistance.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 30 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Wed Aug 15 04:12:19 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools