PROSLOGAN AUDIO IU-4009 Wireless microphone User Manual 1
PROSLOGAN AUDIO LLC Wireless microphone 1
User Manual
PROFESSIONAL
WIRELESS MICROPHONE
----- 1/2/4/8 Channel Wireless System
User’s manual
----- 1/2/4/8 Channel Wireless System
~1~
Precautions
1. To assure the finest performance, please read this manual carefully. keep it in a safe place for future
reference.
2. Do not use force on switches or connection wires. When moving unit, first disconnect the powerplug
and the wires connected to other equipment. Never pull the wire itself.
3. Install this unit in a cool, dry, clean place--- away form window, heat sources of excessive vibration,
dust, moisture and cold. To prevent fire or electrical shock, do not expose this unit to rain or water.
4. Only use provided power adapter, and confirm the voltage is correct to the adapter, The use of
other power adapter may damage the machine and void your warranty.
5. The machine use 220VAC power supply voltage, the use of other voltage may cause fire and fault.
6. Avoid collisions or vibration of the machine.
7. Never open or try to change the circuit of the receiver, transmitters and the power adapter. This
could damage your machine and void your warranty. If the machine fails to work, please send to the
Maintenance Service Center authorized.
8. Be sure to read the"troubleshooting"section regarding common operating errors before concluding
that the unit is faulty.
9. If there are any abnormal cases happened during using, such as smoke,odor,etc.,please unplug the
adapter immediately,and send the machineto the Maintenance Service Center authorized asap.
10. Use the 2A alikline batteries or rechargeable batteries for the transmitter.Be sure the polarities are
correct.(See the illustration inside the battery compartment.)Remove the batteries if the
transmitters will not be used for an extended period of time.
11. When not planning to yse this machine for long periods of time,disconnect the power adapter plug
form the wall outlet.12.Do not attempt to clean the unit with chemical solvente;this might damage
the finish.Use a clean,dry cloth.
Contents Features
The front panel name and function
The rear panel name and function
Handheld Transmitter
Bodypack Transmitter
Six, the infrared frequency
Eight, open process equipment
Technical indicators
3-6
3-6
7
9
10
7
9
~2~
the menu operation method 8
Precautions 1
Contents Features 2
Conference Transmitter 8
~4~
1.The front panel name and function
12 3 35 4
RF Ⅰ
AF Ⅱ
M
H
Z
MUT E
FRE Q.
-3 0 -2 5 - 20 -15 -1 0 -5 0 P EA K
CHANNEL.A
SET SET
CHANNEL.B
RF Ⅰ
AF Ⅱ
M
H
Z
MUT E
FRE Q.
-3 0 -2 5 - 20 -15 -1 0 -5 0 P EA K
45
1, "POWER" power switch;
2, "IR" infrared synchronization window (with the transmitter relative to the
30CM frequency);
3, A/B channel display, real-time display of the working state;
4, A/B channel infrared frequency and function settings;
5, A/B channel selection key;
2.The rear panel name and function
1 2 3
4 5
BALANCE D . B BALANCE D . AMIX OUT
DC 12~15V
500mA ANT . AANT . B VOL. B VOL . A
MIN M AX
MIN M AX
WARN ING :
TO RE DUCE TH E RISK OF F IRE OR EL ECTRI C
SHO CK DO NOT E XPOSE T NIS EQU IPMEN T TO RAIN M OISTU RE
ATTEN TIO N:
RIS QUE DE CH OC ELEC TRUQU E NE PAS OUV RIR
RIS K OF ELEC TRIC SH OCK
DO NO T OPEN
C A U T I O N
SERIAL:
FREQUENC Y:
PROFESSI ON AL WIRELES S SY ST EM
2
34
1, power adapter socket, connect DC/500mA 12V power input;
2, A/B channel antenna socket;
3, potentiometer, A/B channel volume control;
4, parallel output, A and B independent audio XLR parallel output.
5, non parallel output, A and B audio 6.35 mixed output;
~3~
1.The front panel name and function
SET
syn
POWER
UHF WIRELESS MICROPHONE RECEIVER
RF Ⅰ
AF Ⅱ
M
H
Z
MUTE
FREQ.
-3 0 - 25 -2 0 -15 - 10 -5 0 PE AK
12 3 5 4
1, "POWER" power switch;
2, "IR" infrared synchronization window (with the transmitter relative to the
30CM frequency);
3, A channel display, real-time display of the working state;
4, A channel infrared frequency and function settings;
5, A channel selection key;
2.The rear panel name and function
1, power adapter socket, connect DC/500mA 12V power input;
2, A/B channel antenna socket;
3, potentiometer, A/B channel volume control;
4, parallel output, A and B independent audio XLR parallel output.
5, non parallel output, A and B audio 6.35 mixed output;
12 3
5 4
BALANCED
MIX OUT DC 12V/800mA ANT . A
ANT . B
VOLUME
MIN MAX
ATTENTION:
RISQ UE DE CHO C ELECT RUQUE N E PAS O UVRIR
RISK OF ELE CTR IC SH OCK
DO NOT OPEN
C A U T I O N
FREQUENCY:
2
~5~
1
32
BALA NC ED . AMIX OU T DC 12V /8 00mAANT . AAN T . B BALA NC ED . BBALA NC ED . CBALA NC ED . D
VOL. C
MIN M AX
VOL. D
MIN M AX
VOL. A
MIN M AX
VOL. B
MIN M AX
23
4 45
SET
CHANNEL.A CHANNEL.B
SET
CHANNEL.C
SET SET
CHANNEL.D
RF Ⅰ
AF Ⅱ
M
H
Z
MUT E
FRE Q.
-3 0 -2 5 - 20 -15 -1 0 -5 0 P EA K
RF Ⅰ
AF Ⅱ
M
H
Z
MUT E
FRE Q.
-3 0 -2 5 - 20 -15 -1 0 -5 0 P EA K
RF Ⅰ
AF Ⅱ
M
H
Z
MUT E
FRE Q.
-3 0 -2 5 - 20 -15 -1 0 -5 0 P EA K
RF Ⅰ
AF Ⅱ
M
H
Z
MUT E
FRE Q.
-3 0 -2 5 - 20 -15 -1 0 -5 0 P EA K
12 3 35 4 4
5
33 5 445
3.The front panel name and function
4.The rear panel name and function
1, "POWER" power switch;
2, "IR" infrared synchronization window (with the transmitter relative to the
30CM frequency);
3, A/B/C/D channel display, real-time display of the working state;
4, A/B/C/D channel infrared frequency and function settings;
5, A/B/C/D channel selection key;
1, power adapter socket, connect DC/500mA 12V power input;
2, A/B channel antenna socket;
3, potentiometer, A/B/C/D channel volume control;
4, parallel output, A/B/C/D independent audio XLR parallel output.
5, non parallel output, A and B audio 6.35 mixed output;
~6~
1
32
BALA NC ED . EMIX O UT DC 12 V/ 2000m AANT . CAN T . D BALA NC ED . FBALA NC ED . GBALAN CE D . H
VOL. G
MIN M AX
VOL. H
MIN M AX
VOL.E
MIN M AX
VOL. F
MIN M AX
BALA NC ED . AMIX OU T ANT . AAN T . B BALA NC ED . BBALA NC ED . CBALA NC ED . D
VOL. C
MIN M AX
VOL. D
MIN M AX
VOL. A
MIN M AX
VOL. B
MIN M AX
23
4 45
CHANNEL.A
SET
CHANNEL.B
SET
CHANNEL.C
SET SET
CHANNEL.D
CHANNEL.E
SET
CHANNEL.F
SET
CHANNEL.G
SET SET
CHANNEL.H
RF Ⅰ
AF Ⅱ
M
H
Z
MUT E
FRE Q.
-3 0 -2 5 - 20 -15 -1 0 -5 0 P EA K
RF Ⅰ
AF Ⅱ
M
H
Z
MUT E
FRE Q.
-3 0 -2 5 - 20 -15 -1 0 -5 0 P EA K
RF Ⅰ
AF Ⅱ
M
H
Z
MUT E
FRE Q.
-3 0 -2 5 - 20 -15 -1 0 -5 0 P EA K
RF Ⅰ
AF Ⅱ
M
H
Z
MUT E
FRE Q.
-3 0 -2 5 - 20 -15 -1 0 -5 0 P EA K
RF Ⅰ
AF Ⅱ
M
H
Z
MUT E
FRE Q.
-3 0 -2 5 - 20 -15 -1 0 -5 0 P EA K
RF Ⅰ
AF Ⅱ
M
H
Z
MUT E
FRE Q.
-3 0 -2 5 - 20 -15 -1 0 -5 0 P EA K
RF Ⅰ
AF Ⅱ
M
H
Z
MUT E
FRE Q.
-3 0 -2 5 - 20 -15 -1 0 -5 0 P EA K
RF Ⅰ
AF Ⅱ
M
H
Z
MUT E
FRE Q.
-3 0 -2 5 - 20 -15 -1 0 -5 0 P EA K
12 3 3533 5 445
3 3 3 3
5 5 5 5
4 4 4 4
4 5 4
5.The front panel name and function
6.The rear panel name and function
1, "POWER" power switch;
2, "IR" infrared synchronization window (with the transmitter relative to the
30CM frequency);
3, A/B/C/D/E/F/G/H channel display, real-time display of the working state;
4, A/B/C/D/E/F/G/H channel infrared frequency and function settings;
5, A/B/C/D/E/F/G/H channel selection key;
1, power adapter socket, connect DC/500mA 12V power input;
2, A/B/C/D channel antenna socket;
3, potentiometer, A/B/C/D/E/F/G/H channel volume control;
4, parallel output, A/B/C/D/E/F/G/H independent audio XLR parallel output.
5, non parallel output, A and B audio 6.35 mixed output;
~8~
9.Conference transmitter
1, microphone head: pick up sound input;
2, liquid crystal display;
3, power switch;
4, infrared port, receive infrared beam, so that the
frequency synchronization;
5, battery warehouse, assembly 2 AA battery;
IR
1
2
3
4
5
10.menu operation
(1), power on and off
1. Press the a power button, the receiver will begin energized and internal CPU initialization,
the system is restored to the when used on a working state.
2, in the boot state, press the power button, the system began to save the current settings,
and then automatically shut down power.
(2), frequency selection
1, according to about "▲" key or " "keys, frequency and channel menu will be flashing. This
could be a direct press" ▲ "key or " "key system Will increase or decrease the frequency
set by the original menu. If the long press "▲" key or" " button for 2 seconds, the
frequency will be quick step Or reduced.
(Note: Each channel operation method is the same)
2, choose a good frequency, press the "SET" button to send the infrared data to determine
the exit, such as no operation, the menu is flashing 5 confirmed exit.
▲
▲
▲
8.Bodypack Transmitter
7.Handheld Transmitter
~7~
1, Voice head module: pick up audio input;
2, IR window: IR infrared synchronous frequency window, Host frequency
synchronization data;
3, Display: display working status;
4, Power switch, long press the power switch;
5, Battery warehouse: the assembly of 2 AA batteries;
6, Transmit antenna;
2
1
IR UP AC T DO WN
3
4
5
6
7
8
9
1, power switch;
2, status indicator;
3, microphone input socket;
4, transmit antenna;
5, LCD display;
6, infrared frequency window;
7, battery warehouse (assembly
2 AA battery);
8, infrared ray key;
9, high and low emission power
conversion;
POW ER P OWE R
1
2
3
5
4
AA X 1.5 v AA X 1.5v
AA X 1.5 v AA X 1.5 v
IR
1
2
3
4
5
~10~
13.Technical index
Wireless Receiver
In the frequency range
maximum deviation + 15KHz
In the letter exercise than >100dB
comprehensive distortion less than 0.02%
frequency stability + 0.03%
audio response + 40 Hz-16 KHz
dynamic range >100dB
rated working current 480 Ma
working temperature -20 to +50 DEG C
receiver voltage: DC 12 ~ 15V
rated working current 150 mA
AC - receiver voltage 100 ~ 240V
Effective working distance 100 meters
Wireless Transmitter
In the frequency range
maximum deviation + 15KHz
In the letter exercise than >100dB
comprehensive distortion less than 0.02%
frequency stability + 0.03%
audio response + 40 Hz-16 KHz
dynamic range >100dB
Power 8.5mW
working temperature -20 to +50 DEG C
battery time 10-12 hours
rated working current 150 mA
~9~
11.infrared automatic frequency
1, the receiver set good working frequency.
2, open the transmitter power, the infrared receiver window at the receiver of the infrared emission
window, press the "SET" button, the transmitter frequency The rate is automatically set to the
receiver frequency. (Note: all channels are identical).
1, the two antennas are respectively mounted on the back panel of the antenna connecting seat, and
the antenna is pulled to the position of the vertical line into a 45 degree angle.
2, the output of the DC power adapter is connected to the DC power input socket of the receiver, and
the other end is connected to the AC power outlet.(Note: the AC power source for the power
adapter must be in accordance with the specifications of the area.)
3, can not be connected to the parallel mixed output socket: at the same time, the output of the A
channel and B channel audio signal.
4, can be connected to the parallel output socket, A, B channel audio parallel output socket is
independent.
5, in order to make the machine to obtain a good reception, the receiver must be installed on the
ground to less than 1 meters from the ground, the transmitter and the receiving antenna
Less than 2 meters, more than 1 meters above the surface of the wall.
6, to keep the antenna away from the interference sources, such as computer equipment, digital
equipment, television, also want to stay away from large areas of metal objects.
7, the use of the receiver and transmitter between the use of the site as far as possible to reduce
obstacles between the line of sight for the best.)
12.the receiver installed
RF Ⅰ
AF Ⅱ
M
H
Z
MUT E
FRE Q.
-3 0 -2 5 - 20 -15 -1 0 -5 0 P EA K
CHANNEL.A
SET SET
CHANNEL.B
RF Ⅰ
AF Ⅱ
M
H
Z
MUT E
FRE Q.
-3 0 -2 5 - 20 -15 -1 0 -5 0 P EA K
AA X 1.5 v AA X 1.5 v
IR
510.5MHz-585MHz UHF
510.5MHz-585MHz UHF
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used
in portable exposure condition without restriction.