PSC 94418 PSE User's Guide 2K5 MASTER(94418)_single Pages User Manual To The B7376a5e 016b 4a35 B515 0119512c4d19

User Manual: PSC 94418 to the manual

Open the PDF directly: View PDF .
Page Count: 12

Precision Shooting Equipment, Inc.

Compound Bow

User’s Guide

Thank you from the entire

PSE family for purchasing a

PSE bow. Your PSE bow was

manufactured from the finest

materials available and hand-

crafted with pride in the USA.

With proper care and use you

will enjoy this product for

years to come.

We at PSE wish you much

success in the archery field

you have chosen to pursue.

Please read this entire

booklet before shooting or

adjusting your bow.

Remember, most adjustments

to a compound bow should be

made in a bow press.

Whenever shooting a bow, be

certain of your target as well

as what else lies downrange.

LIMB

BOLT

SIGHT

ARROWREST

GRIP

STABILIZER

IDLER WHEEL

CABLE

STRING

PEEP

SIGHT

STRING

LOOP

CABLE

GUARD

CABLE

GUARD

SLIDE

BOW SLING

RISER

CAM

TYPICAL

ONE-CAM

BOW

BOW TERMINOLOGY

Fill out the reverse side

of this page completely,

remove it, and mail to:

PSE Warranty Registration

P.O. Box 5487

Tucson, AZ 85703

REGISTRATION

PN 94418

Rev. 11/04

LIMB

POCKET

SERIAL # OF BOW

BOW MODEL

NAME

ADDRESS

ADDRESS APT

CITY STATE

COUNTRY POSTAL CODE

EMAIL ADDRESS

DATE PURCHASED / / PHONE ( )



IMPORTANT

WARRANTY REGISTRATION

THIS FORM MUST BE RECEIVED BY PSE WITHIN

30 DAYS OF PURCHASE TO ACTIVATE WARRANTY

MAIL TO: PSE WARRANTY REGISTRATION

P. O. BOX 5487

TUCSON, AZ 85703

Your local Authorized PSE Dealer is your best

source for information and assistance.

Visit them for these and other typical services:

1. Adjusting draw length and draw weight

2. Adjusting / changing let-off

3. Replacing / servicing strings and cables

4. All aspects of bow tuning

5. Correct arrow selection

6. Mounting new accessories

7. Adjusting tiller

LIMB

BOLT

SIGHT

ARROWREST

GRIP

STABILIZER

IDLER WHEEL

CABLE

STRING

PEEP

SIGHT

STRING

LOOP

CABLE

GUARD

CABLE

GUARD

SLIDE

BOW SLING

RISER

CAM

TYPICAL

ONE-CAM

BOW

PN 94418

Rev. 11/04

LIMB

POCKET

520-884-9065

www.pse-archery.com

Precision Shooting Equipment, Inc.

Compound Bow

User’s Guide

Thank you from the entire

PSE family for purchasing a

PSE bow. Your PSE bow was

manufactured from the finest

materials available and hand-

crafted with pride in the USA.

With proper care and use you

will enjoy this product for

years to come.

We at PSE wish you much

success in the archery field

you have chosen to pursue.

Please read this entire

booklet before shooting or

adjusting your bow.

Remember, most adjustments

to a compound bow should

be made in a bow press.

Whenever shooting a bow, be

certain of your target as well

as what else lies downrange.

BOW TERMINOLOGY

• Always inspect your bow thoroughly before each shooting session to insure

that it is in good working order. Check for worn or missing components and have

them replaced as required, i.e. bushings, spacers, etc.

• Inspect your arrows to insure that they are straight and that each nock is in

good condition. A cracked nock can break when fired from the bow and cause

the bow to "dry fire" resulting in possible injury to the archer and damage to the

bow.

• When purchasing arrows for your bow, consult the selection chart from the

arrow manufacturer and select the correct arrow for your application. Always

use an arrow that meets the weight requirement marked on the

specification label on the lower limb of your bow. Failure to do so could cause

personal injury and damage to your bow.

Your PSE bow will give you many years of service if maintained and cared

for properly.

IMPORTANT: Before servicing any PSE bow in a bow press, back out each limb

bolt 4 complete turns from bottomed position.

• Keep synthetic cables and strings waxed. Apply bow string wax to your

synthetic cables and string before each shooting session.

• Strings and cables must be replaced periodically. A worn cable or string can

suddenly break causing serious injury to the archer and damage to the bow. It is

recommended that the string and cables be replaced at least every 5,000 shots

or 12 months.

• Always store your bow in a cool dry place. High temperatures, such as those

that can occur in a truck or interior of a vehicle, can cause serious damage to

your bow.

• After use in high humidity or damp conditions, wipe metal components of bow

with a light oil.

Get the PSE BOW OWNER'S GUIDE video at

www.pse-archery.com. This entertaining and

informative video covers all aspects of modern

bow technology. 60 minutes.

GENERAL OPERATING INSTRUCTIONS

BOW MAINTENANCE

SETTING-UP YOUR BOW

NOCKING POINT PLACEMENT:

Finger shooters: For the initial setting,

install the nocking point on the bowstring

approximately 5/16" plus the arrow width

above a point where a horizontal line from

the rest intersects the string.

Release Aid shooters: Install the nock-

ing point the width of the arrow above a point

where a horizontal line from the rest inter-

sects the string. When the arrow is in posi-

tion on the rest the arrownock should fit snug

against the bottom of the nocking point.

ARROWREST ADJUSTMENT:

The in/out position of the arrowrest should

be adjusted so that the arrow is in

alignment with the string when shooting with a

release aid. The arrow tip should be ~1/2 shaft

diameter left of center on a right-handed bow,

(opposite for left-handed) when shooting with

fingers.

As with any weapon, safe operation of your PSE bow must always be the

highest priority. ALWAYS WEAR SAFETY GLASSES WHEN HANDLING A BOW.

Do not attempt to use your bow without proper instruction. Doing so can result in

serious injury.

a. Never "dry-fire" any bow. Dry-fire is to draw and release the bowstring

without an arrow on the string. Dry-firing will likely cause damage to the bow and

serious injury to the archer.

b. Always be sure of your intended target as well as what lies behind the

target area. An arrow can travel a considerable distance, so it is important to have

a safe and sound backstop.

c. If you draw a bow and need to let it down, do so in a slow and careful

manner. Keep your support arm straight and prepare for a rapid and violent

let-down. Avoid hitting your hand on protruding accessories such as the cable guard

or quiver. Keep your head and face back and out of danger during let-down. Never

draw a bow with a peak weight above your comfort level. Always use a bow sling

when drawing a bow.

d. Never modify any part of the bow or its components by drilling extra holes or

removing material. This voids the warranty and presents safety problems.

SAFETY

SIGHT ADJUSTMENT:

When adjusting the sight pin locations, always remember to "follow the

group". That is, if the shot group is to the left of the target, move the sight pins

to the left. If the shot group is low, move the sight pins down.

SETTING-UP YOUR BOW

••

•

INSTALLATION OF ACCESSORIES

Arrowrest/Overdraw: The arrowrest or overdraw should be

installed according to the instructions received with the

product. It is usually mounted to the riser in the threaded hole

on the side opposite the shelf (hole "A") using the hardware

provided with the arrowrest or overdraw.

Sight: The sight should be installed according to the

instructions received with the product. It is usually mounted to

the riser in the threaded holes (holes "B") on the side opposite

the shelf using the hardware provided with the sight.

Stabilizer: The stabilizer should be mounted

according to the manufacturer's recommendation. It is usually

mounted in the threaded hole on the front of the riser (hole "C").

Bow Sling: The bow sling attaches to the riser of the bow

generally with the stabilizer. If a stabilizer is not used, attach the

sling to the riser with the correct sized bolt using the hole pro-

vided for the stabilizer (hole "C").

Hole

Holes

Hole

CABLE GUARD ADJUSTMENT & INSTALLATION:

Install the cable guard as shown in Figure A.

Adjust the cable guard so the cables just clear the

arrow vanes. On bows using an offset cable guard

rod, adjustments must be done with the rod in the

up position (approximately 1 o’clock) as shown in

Figure B (11 o’clock for left handed bows).

Excessive arrow clearance may cause the

cable to track incorrectly on the wheels

and cause personal injury and/or

damage to the bow.

Figure A Figure B

OTHER ADJUSTMENTS

Draw Weight: Your bow is factory-set to within 2 lbs. of the peak draw

weight indicated on the label on the lower limb of the bow. Changes in draw

weight can be made by turning the limb bolt in or out. Before making any

changes in weight, turn the limb bolt clockwise until it no longer moves.

Never use extreme torque when turning the bolt or damage to the limb may

occur. The limb bolt then may be turned counterclockwise to obtain the

desired weight, but NEVER more than 4 turns or revolutions. Adjust

each limb exactly the same. CAUTION: On some bow models, the limb bolt

locking screw MUST be loosened BEFORE adjusting.

Wheels/Cams: Many PSE wheels and cams have adjustable features.

Each one comes from the factory set-up and ready to use but there may

be occasions where you need to adjust the characteristics of your bow. In

some cases you will need a PSE Tune Chart to determine what to adjust,

and you may need to see a PSE Dealer for information. If you are not sure

of the adjustment you are making, stop and see your PSE Dealer for

assistance. In all cases, an appropriate bow press will be needed to make

adjustments to cams and wheels. If you do not have an appropriate press,

see your PSE Dealer.

Centerfire™, Rimfire™& NRG™One Cams:

Draw Length: To change the draw length in 1" increments

the module must be changed. See your PSE Dealer for

information on how to obtain a replacement module. For

minor changes in draw length, the bow must be placed in a

suitable bow press and with tension relieved from the

string/cable.

For Centerfire™: Move the string from the "B" peg to the "C"

peg to shorten draw by approximately ¼" or to the "A" peg

to lengthen draw by approximately ¼". The string can also

be moved from the "2" peg to the "3" peg to shorten draw

by ¼" or to the "1" peg to lengthen draw by approximately

¼".

For NRG™: Each side of the cam has two posts. Moving the

string from the post with the dot to the post without a dot on

the string side of the cam increases the draw length by

approximately 3/8". Moving the string from the post with the

dot to the post without a dot on the take-up side of the cam

decreases the draw length by approximately 1/8".

For Rimfire™: There are two posts on the string side of the

cam. The bow is shipped from the factory with the string on

the far peg. Moving the string to the peg nearest the string

groove increases draw by approximately 1/2".

CAM ADJUSTMENTS

Yoouur

Auutthooriizzeed

PSE

Deealeer

iiss

ssuuppliieed

wiitth

tteecchniiccal

iinffoormattiioon

oon

PSE

boowss

and

ccamss.

Pleeassee

sseeee

yoouur

Deealeer

ffoor

assssiissttanccee

wheen

makiing

ttheessee

adjuussttmeenttss.

Rimfire™

NRG™

Centerfire™

CAM ADJUSTMENTS

NRG™Hybrid Cam:

Draw Length: To change the draw length in 1" increments

the modules must be changed on both the top and bottom

cams. See your PSE dealer for information on how to

obtain replacement modules. For minor changes, the bow

must be placed in a suitable bow press and with the

tension relieved from the string/cable, move the string to

the "+" peg on the top cam to increase the draw length by

approximately 3/8" or to the "-" peg to decrease the draw

length by approximately 3/8".

Draw Stop: The draw stop is located on the bottom cam and

is attached with two screws. It must be placed in the position

that corresponds with the modules. For example, if the bow

is equipped with size 7 modules, the draw stop must be

secured firmly with the screws in the number "7" holes.

Let-off: The let-off adjustment is part of the draw stop. To

adjust from the factory setting of 80% to 65%, remove both

screws which hold the stop to the cam and flip it over so that

the cable will contact the side marked "65" at full draw and

reinstall the screws. Note: Changing the let-off from 80% to

65% shortens the draw length by approximately 3/8".

NRG™Hybrid Cam

TOP

NRG™Hybrid Cam

BOTTOM

Draw Stop: The position of the draw stop must match the

size of the module. If the bow is equipped with a size 7

module, the draw stop must be attached to the cam using

the holes marked with the number 7. The size 4 Centerfire™

and Rimfire™modules are the only exceptions to this rule

as the module and stop are one piece.

Let-off: Let-off adjustment is part of the draw stop. To

adjust from 80% to 65%, remove both screws which hold

the stop to the cam, flip the stop over so that the cable will

contact the side marked 65% at full draw and reinstall the

screws. There is no let-off adjustment for the size 4

Centerfire™module. The Rimfire™cam has no provision for

let-off adjustment.

CAM ADJUSTMENTS

Synergy 4™:

Draw Length: The draw length is adjusted by placing the

bow in an appropriate bow press and relieving the tension

from the string and cables. Shortening the effective length of

the string shortens the draw length and lengthening it

lengthens the draw. The bow is shipped from the factory with

the string in the middle slot. Moving the string one slot on

one of the wheels changes the draw length ¼". Moving the

string one slot on each of the two wheels makes a change

of ½". The cables can be moved to change the draw length

by ½". Adjustments to the cable must be made on both

wheels. Remember, shortening the draw length decreases

the draw weight and lengthening the draw length increases

the draw weight.

Stage 3™:

Draw Length: The draw length is adjusted by placing the

bow in an appropriate bow press and relieving the tension

from the string and cables. Move the string to the slot that

will shorten the effective length of the string to shorten

the draw length by ½" per wheel. Move the string to the

slot that will lengthen the effective length of the string to

lengthen the draw of the bow by ½" per wheel.

NOVA ONE-CAM:

Draw Length: The draw length may be adjusted by

placing the bow in an appropriate bow press relieving

the tension from the string and cable. Moving the string

from the center peg to the peg furthest from the string

groove shortens the draw length by approximately ½".

Moving it to the peg closest to the string groove increas-

es the draw length by approximately ½".

Synergy 4™

Stage 3™

LIMITED LIFETIME WARRANTY

PREFERRED PARTNERS

Mossy Oak®www.mossyoak.com

Primos®www.primos.com

Swarovski Optik®www.swarovskioptik.com

Vibracheck®www.vibracheck.com

ALL PSE MANUFACTURED BOWS / ACCESSORIES / KING PRODUCTS

Each PSE Bow, Accessory and King product is backed by a PSE Limited Lifetime

Warranty to the original owner for the life of the product. Product will be replaced or

repaired to restore it to its original performance. Cables, strings, or wearable items are

not covered by this warranty.

Evidence of abuse, mishandling, misuse, or alteration to any PSE product voids any

claim to warranty. PSE specifications on strings and harness must be adhered to.

PSE cannot be held responsible for injury or product failure resulting from improper use

or neglect of maintenance.

All bows must undergo string and cable changes every 5,000 shots or every 12 months

to maintain PSE warranty coverage. Total arrow weight must be in accordance with the

recommendations made by the Archery Trade Association (ATA) for minimum arrow

weight/bow peak weight. Overstressing PSE compound bows by using arrows lighter

than ATA recommendation will void warranty and may cause damage to the bow or

injury to the shooter.

PSE makes no other claims either expressed or implied. In the interest of

product improvement and consumer safety, PSE reserves the right to make changes in

product design, color, and specifications without notice.

PATENT INFORMATION

One or more of the following patents may apply:

4,649,889

4,697,350

4,735,667

4,739,744

4,748,962 B1

4,762,112

4,947,823

4,967,721

5,005,554

5,020,507 B1

5,040,520

5,054,462

5,123,396

5,190,022

5,241,945

5,243,958

5,280,779

5,301,651

5,307,787

5,335,644

5,339,790

5,365,650

5,377,658

5,469,834

5,479,712

5,487,373

5,495,843

5,505,185

5,507,270

5,657,739

5,678,529

5,762,060

5,914,775

5,960,778

6,112,732

6,176,231 B1

6,360,735

6,493,951 B1

6,792,930

DES 429,309

RE-36,942

YES, send me two videos and my free cap!

Please select two videos from below:

WHITETAIL FEVER 3 PETE’S JOURNAL Boar’n the USA Free Hat

VHS 41270 DVD 41296 VHS ONLY 41045 VHS 41266 DVD 41295

PURSUIN’ THE BRUIN HOLDING STEADY BOWHUNTING THE WILD WEST 3

VHS 45092 DVD 41303 VHS 45081 DVD 41302 VHS 41351 DVD 41347

Name

Address

City State / Province

Postal Code (Zip) Country Daytime Phone ( )

CREDIT CARD NUMBER

MC Visa Exp

OR INCLUDE CHECK OR MONEY ORDER

SIGNATURE

Mail to: PSE P.O. Box 5487 Tucson, AZ 85703

$ 18.99

3.95

$22.94

1.32

24.26

Shipping & Handling

Total (non-AZ residents)

AZ residents add

Total (AZ residents)

45354

THANK YOU FOR

SELECTING PSE.

Buy TWO of these

PSC 94418 PSE User's Guide 2K5 MASTER(94418)_single Pages User Manual To The B7376a5e 016b 4a35 B515 0119512c4d19

Navigation menu

Versions of this User Manual:

Views

Navigation