PaloSanto Solutions NLX4000 Elastix NLX4000 User Manual elastix NLX4000

PaloSanto Solutions Elastix NLX4000 elastix NLX4000

Manual

Elastix NLX4000 User Manual
www.elastix.com 1 Copyright Copyright© 2013 Elastix Inc. All rights reserved. No part of this document may be reproduced without prior written permission. Disclaimer Elastix Inc. reserves the right to modify the design, characteristics, and products at any time without notification or obligation and shall not be held liable for any error or damage of any kind resulting from the use of this document. Elastix has made every effort to ensure that the information contained in this document is accurate and complete; however, the contents of this document are subject to revision without notice. Please contact Elastix to ensure you have the latest version of this document. Trademarks All other trademarks mentioned in this document are the property of their respective owners. FCC warning statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
www.elastix.com 2 Recycling / disposal Do not discard electronic products in household trash! All waste electronics equipment should be recycled according to local regulations. Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. • If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer. Operation safety • Before installing devices into the system, carefully read all the documents that came with the package. • Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately. • To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry. • Avoid dust, humidity, and temperature extremes. Do not place the product in any area where it may become wet. Place the product on a stable surface. • If you encounter technical problems with the product, contact a qualified service technician or your retailer. ---------------------------------------------------- Lithium-Ion Battery Warning CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturerís instructions.
www.elastix.com 3 Chapter 1 System introduction 1.1 Welcome! This chapter lists the system features, including introduction on the front and rear panel, and internal components, Thank you for choosing the elastix NLX4000. The system motherboard supports the Intel Atom N2600XX/D2500XX series processors and combined with the Intel NM10 Chipset to set a new benchmark for an effective desktop platform solution. The system supports up to 4GB of system memory using DDR3 1333MHZ SODIMMs, high-resolution graphics integrated graphics controller .serial ATA RAID, USB 2.0, and PCIe x4 solt. 1.2 Front panel The front panel include LCD panel display and control buttons, power button . 1. Power button , press this button to turn the system on. 2. Lcd panel display, the Lcd panel can display various operating states of the system. 3. Lcd panel control buttons. Enter function. 4. Lcd panel control buttons. Down function. 5. Lcd panel control buttons. Exit function. 6. Lcd panel control buttons. Up function.
www.elastix.com 4 1.3 Rear panel The system rear panel includes power connector and several I/O ports that allow convenient connection of devices. 1. Expansion slot covers. Remove these cover when installing expansion cards. Expansion card is replaceable. 2. VGA port. This port connected with a VGA monitor. 3. LAN (RJ-45) port. This port allows Gigabit connection to a Local Area Network (LAN) through a network hub. 4. LAN(RJ-45) port. This port allows Gigabit connection to a Local Area Network (LAN) through a network hub. 5. USB 2.0 ports 1 and 2. These 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices 6. Power connector. This connector is used for the power cable and plug. (input AC100V_240V) 1.4 Internal components The illustration below is the internal view of the system when you remove, the top cover and the power supply unit. The installed components are labeled for your reference.
www.elastix.com 5 1. Power supply unit 2. Hard disk power support 3. SATA connectors 4. GPIO connectors 5. USB connector 6. LCD panel display connectors 7. Motherboard power connector 8. Expansion slot 9. Power button connectors’ cable Chapter 2 System introduction This chapter provides instructions on how to install components in the system step-by-step. 2.1 Preparation Before you proceed, make sure that you have all the components you plan to install in the system. Basic components to install 1. Motherboard 2. DDR Memory Module (SODIMM) 3. Expansion solts 4. Hard disk drive 5. Optical drive
www.elastix.com 6 Tool Phillips (cross) screw driver 2.2 Before you proceed Take note of the following precautions before you install components into the system. • Use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity. • Hold components by the edges to avoid touching the ICs on them. • Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that came with the component. The motherboard comes with an onboard standby power LED. This LED lights up to indicate that the system is ON, in sleep mode or in soft-off mode, and not powered OFF. Unplug the power cable from the power outlet and make sure that the standby power LED is OFF before installing any system component. 2.3 Installing a SODIMM The system motherboard has a DDR3 Memory (SODIMM) sockets which supports up to 4GB Memory. The following figure illustrates the location of the sockets 2.4 Expansion slots Elastix NLX4000 Based on plug-in modular design. It allows users to integrate up to 2 pieces of PCI-E x1 telephony cards and supports to combine with analog, BRI, PRI, GSM .
www.elastix.com 7 Chapter 3 Motherboard info This chapter gives information about the motherboard that comes with the system. This chapter includes the motherboard layout, jumper settings, and connector locations. 3.1 Specification  CPU: Intel Atom N2600_1.6Ghz/D2500_1.86Ghz/D2550_1.86Ghz  DRAM: Slot Onboard, up to 4GB DDR3 1333 SDRAM ( Atom N2600 only support 2GB)  Chipset: Intel NM10 Express Chipset  Southbridge: Intel NM10  Storage: 1 SATA slot, 1 mSATA Socket  Three front panel LEDs, for 3 programmable GPO status indicator  Push button: for mode setting switch, accessing a programmable GPI, active low means switch is pressed  PCIe Interface : PCIe x4 Golden Finger  Expansion: 1 Mini PCIe slot  Connectivity: Up to 2 Ethernet channels (10/100/1000Mbps speed) 2 PCIe Ethernet controllers Support PXE (for remote booting)  I/O: 1*DB15 VGA port, 5*USB 2.0 port  Board size: 6 x 6" (152.4 x 152.4 mm)  Temperature: 0°C to 60°C (contact factory for more temp. options)  Firmware: AMI_UEFI BIOS  PCB layer: 4  Power dissipation: ~7.8W (Minimum Power Dissipation)
www.elastix.com 8 3.2 Motherboard layout 3.3 Connector and Jumper List Name Function VGA1 VGA display output CN10 PCIe x4 Golden Finger JP1 Clear CMOS CN15 Main Power in Jacket CN16 Power Supply Jacket U4 DDR3 Memory Slot CN11 mSATA Slot CN13 Mini PCIe Slot CN2 Ethernet 1 CN3 Ethernet 2 CN5 SATA Interface CN4 SATA power supply CN8 USB Port CN1 LPC interface
www.elastix.com 9 JP5 Manual Reset In CN6 External LEDs and GPIO CN18/CN9 USB connector CN14 SIM Socket FAN1 FAN power supply SW1 GPI switch 3.4 Specification  CPU: Intel Atom N2600_1.6Ghz/D2500_1.86Ghz/D2550_1.86Ghz  DRAM: Slot Onboard, up to 4GB DDR3 1333 SDRAM ( Atom N2600 only support 2GB)  Chipset: Intel NM10 Express Chipset  Southbridge: Intel NM10  Storage: 1 SATA slot, 1 mSATA Socket  Three front panel LEDs, for 3 programmable GPO status indicator  Push button: for mode setting switch, accessing a programmable GPI, active low means switch is pressed  PCIe Interface : PCIe x4 Golden Finger  Expansion: 1 Mini PCIe slot  Connectivity: Up to 2 Ethernet channels (10/100/1000Mbps speed) 2 PCIe Ethernet controllers Support PXE (for remote booting)  I/O: 1*DB15 VGA port, 5*USB 2.0 port  Board size: 6 x 6" (152.4 x 152.4 mm)  Temperature: 0°C to 60°C (contact factory for more temp. options)  Firmware: AMI_UEFI BIOS  PCB layer: 4 Power dissipation: ~7.8W (Minimum Power Dissipation) 3.5 Connector and Jumper Description JP1 clear CMOS Setting Function Close 1-2 Clear CMOS Open 1-2 (default) Normal CN15 Main Power Jacket DC in @12V
www.elastix.com 10 1 2 Pin Name 1 Gnd 2 Vin CN16 Power Supply Jacket DC out @12V Pin Name 1 Vin 2 Gnd U4 DDR3 Memory Slot  1.5V  DDR3  ATOM N2600 CPU Support Max Memory Size 2GB of DRAM  ATOM D2550 CPU Support Max Memory Size 4GB of DRAM CN13 Mini PCIe Slot Attach 3G SIM card to CN14, and attach Mini PCIe 3G module to CN13，implement 3G function for NLX4000.
www.elastix.com 11 CN2/CN3 Giga Ethernet Port Pin Name 1 BI_DA+ 2 BI_DA- 3 BI_DB+ 4 BI_DC+ 5 BI_DC- 6 BI_DB-
www.elastix.com 12 7 BI_DD+ 8 BI_DD- CN5 SATA Interface Pin Name 1 Ground 2 Transmit + 3 Transmit - 4 Ground 5 Receive - 6 Receive + 7 Ground CN4 SATA Power Supply Pin Name 1 5v 2 Ground 3 Ground 4 12v CN8 USB Port 2 USB2.0 ports. 500 mA Continuous Current per Channel. Short-Circuit and Thermal Protection with Overcurrent Logic. Pin Name Pin Name 1 5v 5 5v 2 Data- 6 Data- 3 Data+ 7 Data+ 4 Ground 8 Ground CN9 USB connector
www.elastix.com 13 Pin Name 1 5v 2 Data- 3 Data+ 4 Ground CN18 USB connector Pin Name Pin Name 1 5v 2 Ground 3 Data- 4 Data+ 5 Data+ 6 Data- 7 Ground 8 5v CN1 LPC Interface Pin Name Pin Name 1 LPC_CLK 9 AD3 2 SERIRQ 10 +3.3V 3 AD0 11 FRAME# 4 NC 12 GND 5 AD1 13 GND 6 GND 14 NC 7 AD2 15 48MHz_CLK 8 +5V 16 NC JP5 Manual Reset In Setting Function Close 1-2 Reset System Open 1-2 (default) Normal CN6 External LEDs and GPIO 2*4*2.0mm header 3.3V 200mA max CMOS output
www.elastix.com 14 Pin Name Pin Name 1 LED1P (3.3V) 2 LED1N 3 LED2P(3.3V) 4 LED2N 5 LED3P(3.3V) 6 LED3N 7 GPIO 8 GND 3.6 System Status LEDs Indicator & SW1 How to use the status indicator LEDs and Micro switch SW1? After system completed boot, enter I/O space based address 500H and change some register value as follow: LED16 1. Set 5000H+0CH, bit7 2. the LED will light 3. clear the 500H+0CH, bit7 4. the LED will dark LED17 1. Set 500H+0CH, bit6 2. the LED will light 3. clear the 500H+0CH, bit6 4. the LED will dark LED6 1. Set 500H+0FH, bit28 2. the LED will light 3. clear the 500H+0FH, bit28 4. the LED will dark SW1 1. Set 500H+0DH, bit13 ,means direction is input 2. press SW1 ,then 500H+0DH ,bit13 will be changed to 0 3. when SW1 release, 500H+0DH ,bit13 will be changed to 1 (default)
www.elastix.com 15 CN6 7-8pin GPIO As output 1. Clear 500H+0DH, bit13, means direction is output 2. Set 500H+0DH, bit13 ,CN6 7pin will be changed to 1 (High level) 3. Clear 500H+0DH, bit13 ,CN6 7pinwill be changed to 0 (low level) As input 1. Set 500H+0DH, bit13, means direction is input 2. CN6 7Pin input 1 (High level), then 500H+0DH, bit13 will be changed to 1 3. CN6 7pin input 0 (Low level), then 500H+0DH, bit13 will be changed to 0 Chapter 4 BIOS Setup Guide PXE remote boot function setup Press the “del” key, Enter the BIOS, system will display information as following: PXE remote boot function setup a. Enter Boot menu – >CSM Parameters Options b. Highlight PXE OpROM control, press enter key, system will prompt as following:
www.elastix.com 16 Legacy only Options enable PXE, Other options disable. c. Enter “exit” menu, then highlight “save changes and exit” item, answer ok to confirm the latest Address: F/3, Building No.127, Jindi Industrial Zone, Shazui Road, Futian District, Shenzhen, Guangdong 518048, China Tel:+86-755-82535461, 82535095, 82535362, Fax:+86-755-83823074 Business Contact: sales@elastix.com.cn Technical Support: support@elastix.com.cn Business Hours: 09:00-18:00(GMT+8) from Monday to Friday URL: www.elastix.cn Thank You for Choosing Elastix Products!

Navigation menu