Panasonic of North America 927128AHP VCR User Manual Copy
Panasonic Corporation of North America VCR Copy
User Manual
2
Important Safeguards and Precautions
This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit
has been included. Therefore, it should be read carefully in order to avoid any problems.
Safety Precautions
Warning: To prevent fire or shock hazard, do not expose this equipment to rain or moisture.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
FOR YOUR SAFETY, READ AND
RETAIN ALL SAFETY AND OPERATING
INSTRUCTIONS. HEED ALL WARNINGS
IN THE MANUAL AND ON THE UNIT
USING THE VIDEO UNIT
If the unit has been in storage or moved to a new location,
refer first to the INSTALLATION section of these safeguards.
1 KEEP THIS VIDEO UNIT AWAY FROM WATER OR
MOISTURE OF ANY KIND.
2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR
STRONG IMPACT, unplug the unit and have it inspected by a qualified
service technician before use.
3 DURING AN ELECTRICAL STORM
During a lightning storm, whether indoors or outdoors, or before leaving the
unit unused for extended periods of time, disconnect all equipment from the
power source as well as the antenna and cable system.
4 WHEN THE UNIT IS PLUGGED IN
• Never expose the unit to rain or water. DO NOT OPERATE
if liquid has been spilled into the unit. Immediately unplug the unit,
and have it inspected by a service technician. Fire and shock hazards
can result from electrical shorts caused by liquid contact inside.
•
Never drop or push any object through openings in the unit. Some internal parts
carry hazardous voltages and contact can cause electric shock or fire hazard.
• Avoid placing the unit directly above or below your TV set as this may cause
electrical interference. Keep all magnets away from electronic equipment.
5 USING ACCESSORIES
Use only accessories recommended by the manufacturer to avoid risk of fire,
shock, or other hazards.
6 CLEANING THE UNIT
Unplug the unit. Then, use a clean, dry, chemically untreated cloth to gently
remove dust or debris. DO NOT USE cleaning fluids, aerosols, or forced air
that could over-spray, or seep into the unit and cause electrical shock.
Any substance such as wax, adhesive tape, etc. may mar the cabinet surface.
Exposure to greasy, humid, or dusty areas may adversely affect internal parts.
INSTALLATION
1 POWER SOURCE CAUTION
Operate only from a power source indicated on the unit or in
this manual. If necessary, have your Electric Utility Service
Company or Video Products Dealer verify the power source
in your home.
2 POLARIZED OR GROUNDING PLUG
As a safety feature, this Video product comes with either
a polarized power cord plug (one blade is wider than the
other), or a three-wire grounding type plug.
POLARIZED PLUG CAUTION:
This plug will only fit into an outlet one way. If you cannot
fully insert the plug, try reversing it. If it still will not fit,
have an electrician install the proper wall outlet.
Do not defeat the safety feature by tampering with the plug.
GROUNDING PLUG CAUTION:
This plug will only fit into a three-hole grounding outlet.
If necessary, have an electrician install the proper outlet.
Do not defeat the safety feature by tampering with the plug.
3 POWER CORD
Make sure power cords are routed so that they are not likely
to have anything rest on them, roll over them, or be in the
way of walking traffic. If an extension cord is used, make
sure it also has either a polarized or grounded plug and that
the cords can be securely connected. Frayed cords, damaged
plugs, and damaged or cracked wire insulation are hazardous
and should be replaced by a qualified service technician.
Overloaded outlets and extension cords are fire hazards and
should be avoided.
4 DO NOT BLOCK VENTILATION HOLES
Ventilation openings in the cabinet release heat generated
during operation. If they are blocked, heat build-up inside the
unit can cause failures that may result in a fire hazard or
heat damage to cassettes.
For protection, follow these rules:
a. Never cover ventilation slots or the unit
while in use, or operate the unit when placed
on a bed, sofa, rug, or other soft surface.
b. Avoid built-in installation, such as a book case
or rack, unless proper ventilation is provided.
5 AVOID EXTREMELY HOT LOCATIONS OR
SUDDEN TEMPERATURE CHANGES
Do not place the unit over or near any kind of heater
or regulator, in direct sunlight, inside a closed vehicle, etc..
Do not move the unit suddenly between areas of extreme
temperature variation. If the unit is suddenly moved from a
cold place to a warm place, moisture may condense in the
unit and on the tape.
6 TO AVOID PERSONAL INJURY
• Do not place unsecured equipment on a sloping surface.
• Do not place this unit on any support
that is not firm, level, and adequately
strong. The unit could fall causing
serious injury to a child or adult and
damage to the unit.
• An appliance and cart combination
should be moved with care.
Quick stops, excessive force, and
uneven surfaces may cause the
appliance and cart combination to overturn.
• Carefully follow all operating instructions and use
the manufacturer's recommended accessories when
operating this unit or connecting it to any other equipment.
SERVICE
1 DO NOT SERVICE THIS PRODUCT YOURSELF
If, after carefully following the detailed operating instructions, this Video
product does not operate properly, do not attempt to open or remove
covers, or make any adjustments not described in the manual.
Unplug the unit and contact a qualified service technician.
2 IF REPLACEMENT PARTS ARE REQUIRED
Make sure the service technician uses only parts specified by the manufacturer,
or those having the same safety characteristics as the original parts. The use of
unauthorized substitutes may result in fire, electric shock, or other hazards.
3 HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK
After any service or repairs to the unit, request the service technician to
conduct a through safety check as described in the manufacture’s service
literature to insure that the video unit is in safe operating condition.
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC
- NATIONAL
ELECTRICAL CODE
OUTDOOR ANTENNA INSTALLATION
1 SAFE ANTENNA AND CABLE CONNECTION
If an outside antenna or cable system
is connected to the equipment,
be sure the antenna or cable system
is grounded so as to provide some
protection against built up static
charges and voltage surges.
Section 810 of the National
Electrical Code, ANSI/NFPA 70
(in Canada, part 1 of the Canadian
Electrical Code) provides information
with respect to proper grounding of the
mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna discharge unit, connection
to grounding electrodes and requirements for the grounding electrode.
2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES
OR CIRCUITS
An outside antenna system should be located well away from power lines,
electric light or power circuits and where it will never come into contact with
these power sources if it should happen to fall. When installing an outside
antenna, extreme care should be taken to avoid touching power lines,
circuits or other power sources as this could be fatal. Because of the
hazards involved, antenna installation should be left to a professional.
NV-FJ4620PX P01-06.p65 00/02/29, 0:342
3
Advanced Connections (Cable/DSS) .................................................... 10
Copying Your Tapes (Dubbing) ......................................................... 11
Timer Recording .......................................................................... 12, 13
Timer Recording Using VCR Plus+ System ............... 14 ~ 19
Multi-Brand Control Feature .................................................... 20, 21
Tape Operation .......................................................................... 22 ~ 29
MTS Broadcast/ VHS Hi-Fi Stereo System ........................ 30, 31
Special VCR Features ............................................................. 32 ~ 37
Reset Language, Channels, Clock, VCR’s Output Channel .. 38, 39
VCR & Cassette Information........................................... 40, 41
On Screen Displays (OSD) ....................................................42
Before Requesting Service...................................................43
Location of Controls ....................................................... 44, 45
Quick Use Guide (Playback, Recording) .................... Back Cover
Important Safeguards and Precautions ...................................... 2
Accessories............................................................................................ 4
Loading the Batteries ......................................................................... 4
Basic Connections (Antenna, VCR, TV) ............................................ 4, 5
One Time VCR Setup (Language, VCR’s Output Channel, Channel, Clock) .. 6, 7
Playback a Tape (Still picture, Frame by Frame picture, Slow Motion) ......... 8
Record On a Tape ................................................................................ 9
Table of Contents
•Channel Caption ................ 32, 33
•Time Stamp ...................... 34, 35
•Tape Position Display ............. 36
•Remote Warning ON/OFF ....... 36
Use
Now!
Enjoy
more!
•One Touch Recording ................ 9
• Auto Operation Functions........ 27
•Direct Access ......................... 28
•Repeat Play ............................ 29
•Zero Search ............................ 29
•Select Audio Mode .................. 31
•Function & Channel Display .... 42
•VCR Status & Clock Display... 42
•Head Cleaning ......................... 41
•Built-in Head Cleaner ............... 41
•Cleaning the VCR .................... 41
•Specifications ......................... 41
•Features for a Quality Picture .. 41
•Blank Tape/ No Video Signal
Indication ................................ 42
•Warning and Instruction Displays .. 42
Other
Information!
•Timer Recording
Using VCR Buttons ................. 12 •Review, Replace or Clear
Program Contents ................... 13
•Commercial Advance ...... 22 ~ 24
•Movie Advance ....................... 25
•Search System ................. 26 ~ 29
• Program End Search ............... 26
• Program Index Search, Index Scan .. 27
•
Stereo/SAP/Mono Broadcast
..
30
•Reset All VCR Memory Functions ... 40
•DST (Daylight Saving Time) .... 40
•Prevent Accidental Tape Erasure .. 40
•Record/Playback Time ............ 40
•Choose your connection type .. 14
•Cable Box Setup ..................... 15
•Auto VCR Plus+ System
Channel Setup................... 16, 17
•Manual VCR Plus+ System
Channel Setup ......................... 18
•VCR Plus+ System
Programming ........................... 19
Advanced Operation For Your Information
Basic Operation
•VCR Lock ................................ 36
•Weak Signal Display
ON/OFF
.... 37
• Auto Shut-Off .......................... 37
NV-FJ4620PX P01-06.p65 00/02/29, 0:343
4
Remote Control
LSSQ0204
Batteries 2 “AA”
RF Coaxial Cable
VJAS0196
Accessories
Battery replacement caution
•Do not mix old and new batteries.
•Do not mix alkaline with manganese batteries.
3) Close the cover.
Loading the Batteries
Congratulations
on your purchase of one of the most sophisticated and
reliable products on the market today. Used properly,
it will bring you and your family years of enjoyment.
Please fill in the information below. The serial number
is on the tag located on the back of your VCR.
•Date of Purchase
•Dealer Purchased From
•Dealer Address
•Dealer Phone No.
•Model No.
•Serial No.
Before Using Basic Connection
1) Open the cover.
2) Insert the
batteries as
marked.
V
C
R
+
Connect VCR and TV with an AV Cable (not supplied) or a
RF Coaxial Cable (supplied) as shown in the figure below.
If your TV has AUDIO and VIDEO IN terminals, connect
them to VCR for higher quality picture and sound.
You can enjoy stereo sound even if your TV is not stereo
by connecting a stereo amplifier to the VCR.
INDOOR ANTENNA
OUTDOOR ANTENNA
CABLE TV
or
ANTENNA (See page 5)
WARNING
When using “Nut type” RF coaxial cables, tighten with fingers
only. Overtightening may damage terminals.
IN
VHF/
UHF
VIDEO AUDIO
RL
OUT
TV
IN
FROM
ANT.
OUT
TO
TV
AUDIO
IN 1 OUT
MONO
VCR
a) AV CABLE
(not supplied)
VHF/UHF
R
L
VIDEO
b) RF
COAXIAL
CABLE
Notes
1) While connection b) (above) is sufficient, connection
a) offers better sound and picture (especially with
this model , you can enjoy Hi-Fi STEREO sound).
2) For both connections a) and b) proceed as follows:
• To use VCR : VCR Power on, set TV to VIDEO.
• To watch TV : VCR Power off, select channel on.
3) Set VCR Output to channel 3 or 4 (not an active
station). (See page 6.)
Use the L Audio OUT jack when connecting to a
monaural TV.
Connect VCR
to TV with RF
Coaxial Cable.
2
Disconnect antenna
or cable from TV and
connect to VCR.
1
Power Plug Adaptor
VJSS0070
Caution:
•Voltage 110V, 220V and 240V are not for use in USA.
•Operation at a voltage higher than 120V AC may require the use of a different AC plug. Please contact either a
local or foreign Panasonic Distributor Center for assistance in selecting an alternate plug.
NV-FJ4620PX P01-06.p65 00/02/29, 0:344
5
•If your TV has both post and plug-type
VHF terminals, the post connection is
recommended to minimize signal loss.
Case 1: Twin Lead Cable Only
Case 2: Twin Lead & Coaxial Cables
Case 3: Two Twin Lead Cables
Case 1: Screw & Plug Type Terminal
Case 2: Screw Type Terminal
Case 3: Double Screw Type Terminal
Case 4: Complex TV Terminal
TERMINALS ON BACK OF TV SET
•Connect to one of the ANT terminals and
select the same antenna number on the TV.
300-75 ohm
Transformer
(not supplied)
UHF/VHF Band Mixer
(not supplied)
To VCR Terminal
TV
ANT2
Split out
ANT1
UHF/VHF Band
Separator
(not supplied)
TV
VHF
UHF
1 Between ANT. and VCR 2 Between VCR and TV
75-300 ohm
Transformer
(not supplied)
TV
VHF
or
UHF
TV
UHF/VHF Band
Separator
(not supplied)
RF Coaxial Cable
VHF
UHF
(Flat) Twin Lead
300 Ohm Cable
To VCR Terminal
(Round) 75 Ohm
coaxial Cable
UHF/VHF Band Mixer
(not supplied)
To VCR Terminal
Basic Connection
From Antenna
300-75 ohm
Transformer
(not supplied)
FCC Warning: Any unauthorized changes or modifications
to this equipment would void the user’s authority to operate.
Note to CABLE system installer:
This reminder is provided to call the CABLE system installer’s
attention to Article 820-40 of the NEC in USA (and to the Canadian
Electrical Code in Canada) that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall
be connected to the grounding system of the building, as close to
the point of cable entry as practical.
NV-FJ4620PX P01-06.p65 00/02/29, 0:345
6
SELE
C
T
HOOKUP
C
ABLE
/
D
SS B
OX
OU
TP
U
T
CH
CH
0
1
SELE
C
T
:
KEY
SET
:
KEY
END
:
AC
T
I
O
N
KEY
C
ABLE
/
D
SS B
O
X
V
C
R
TV
SELE
C
T
:
KEY
SET
:
KEY
END
:
ACT
I
O
N
KEY
SELE
C
T
HOOKUP
C
ABLE
/
D
SS B
O
X
V
C
R
TV
V
CR
CAB
L
E
/
D
SS B
O
X
TV
V
CR
TV
V
C
R
+
2
One Time VCR Setup
Turn the TV and VCR on.
Press POWER*.
1
When VCR is turned on the first time,
setup mode is entered automatically. Process of Setup
Language Channel Clock
1
2
POWER
VCR/TV
CH /
3
•If you selected “CABLE/ DSS
BOX VCR TV,” continue with
step 4 and only the cable box
output channel will be placed in
memory.
If not, go to step 6.
4
•If necessary, refer to cable box manual.
•If you used Audio/ Video jack connection to cable box, set “VIDEO OUT”.
5Turn on cable box and set it to PBS
channel in your time zone.
•If you use DSS receiver, it must be turned off.
SELECT/
SET
:PLAY
:STOP
:FF
3
4
Select hookup.
1) Press
to select.
2) Press
to set.
Select cable box
or DSS receiver
output channel.
1) Press
to select.
2) Press
to enter.
Set TV Channel to CH 3.
2ACTION
• If wrong language is set, do “Reset All VCR Memory Functions”
steps on page 40.
Select the language.
2
SELECT
LANGUAGE
P
US
H
CH
:
EN
G
L
I
SH
O
P
R
I
M
I
R
CH
:
E
SPA
ÑO
L
APP.
VCR
/ TV
:
FRAN
ÇA
I
S
T
O
CHANGE
VCR
’
S
O
UTPUT
CH,
PUSH
ACT
I
ON
KEY.
•Always tune TV to this channel to monitor the VCR.
•If you used audio/video jack connection, tune the TV to its video input.
I
F
YOU
PUSH
ACT
I
O
N
KEY,
VCR’
S
O
UTPUT
CH
S
W
I
TCHES
T
O
CH
4
.
PLEASE
TUNE
Y
O
UR
TV
TO
CH
4
.
Press ACTION
Press ACTION
After 3 seconds
for Spanish
(ESPAÑOL)
for English
for French
( FRANÇAIS)
Display SELECT LANGUAGE.
This display appears for first time setup
only.
When using connection b) (see
page 4), tune TV to VCR’s output
channel.
If there is beat or noise on CH3,
change VCR’s output channel to CH4
by pressing ACTION twice.
•If using AV Cable connection, set TV
to Video instead of channel. (See
connection a) on page 4.)
NV-FJ4620PX P01-06.p65 00/02/29, 0:346
7
S
ET
:
KEY
ST
A
RT
:
ACT
I
O
N KEY
D
ST
:
ON
1
/
4
/
2000
2000
TUE
12
12
:
0
0
P
M
SET
CO
M
P
L
E
T
E
D
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
--
-
-
-
-
-
SET
C
L
OC
K
DST
:
O
N
SE
L
E
C
T
M
O
N
TH
1
/ / :
SELE
C
T
:
KEY
SET
:
KEY
END
:
ACT
I
O
N
KEY
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
--
-
-
-
-
-
SET
C
L
OC
K
AUTO CLOCK SET
I
S
I
NC
O
M
PLETE
PUS
H
ACT
I
ON TO
SET
C
L
O
CK
1
/
4
/
20
0
0
TU
E
12
:
00P
M
END
: PUSH CH UP KEY
D
S
T
:
ON
SETT
I
N
G
: CH
02
AUTO CLOCK SET
C
O
M
PLETED
V
C
R
+
Clock Setup incomplete.
Set the clock manually.
•
Likewise, set date, year, time,
DST (Daylight Saving Time).
To Make Corrections,
repeatedly press to move to
error, then correct.
One Time VCR Setup
Start Channel Auto Set
and Clock Auto Set.
CH
A
NN
EL
/
C
L
OCK
AUT
O
SET
CONN
E
CT
A
NT
E
NN
A CABLE
L
OC
A
L
PB
S
CH
THE
N
.
.
.
AND
I
F
Y
OU
US
E
A
CABLE
B
O
X,
TUNE
I T
TO
Y
OU
R
P
L
E
A
S
E
P
US
H
C
H
U
P
K
E
Y
(Setup completed)
•If your area observes DST (daylight
saving time), but the time is incorrect; do
the “Time Zone Adjust” steps on page 39.
(Setup incomplete)
6
ACTION
SELECT/
SET
:PLAY
:STOP
:REW
:FF
CH
Using keys
You can also operate the menu
screen using VCR buttons.
When menu screens are
displayed, the PLAY, STOP,
REWIND, and FF buttons on
the VCR and remote function
as only with no tape
inserted.
To display menu using VCR
buttons, press CH and CH
together.
To exit the menu, repeat above.
: PLAY
: STOP
: REW
: FF
CH AUTO
SET P
ROCEED
I
NG
Press CH
.
1) Press ACTION.
2) Press to
select month.
3) Press to set.
4) Press ACTION.
(Clock starts.)
•To exit this
mode, press
ACTION again.
•VCR calendar is accurately maintained to
Dec. 31, 2096 11:59PM.
•Channel auto set selects normal TV or Cable
channels depending on your VCR hookup.
•To reset Language, Channels, Clock or
VCR’s Output Channel see pages 38 and 39.
Notes
Press CH
to exit.
Case 2
Case 1
On Remote On VCR
PLAY
STOP/EJECT
REC
REW FF
POWER VCR/TV
VIDEO IN 2 L-AUDIO IN 2-R
/
ACTION
CHANNEL
IMPORTANT NOTE FOR
AUTO CLOCK SET
•Auto clock set is performed the
first time the VCR is turned off
each day. If used, a cable box
must be left on and tuned to the
PBS channel at the time VCR
power is turned off if you want auto
clock set to be done.
•If used, a DSS receiver must be
turned off for auto clock set.
•If Cable Box or DSS receiver is
connected to VCR via Audio/Video
jacks, an RF coaxial cable must
also be connected for auto clock
set and channel auto set features
to work.
*Important: If the remote control POWER, ACTION, PROG/VCR+, CH /, NUMBERED keys,
INPUT, SEARCH/MA SKIP or ADD/DLT button does not work when pressed, press
the VCR button on the remote and try the button again.
AUTO CLOCK SET
P
ROCEED
I
NG
NV-FJ4620PX P07.p65 00/02/29, 0:357
40
PLAY
STOP/EJECT
REC
REW FF
POWER VCR/TV
VIDEO IN 2 L-AUDIO IN 2-R
/
ACTION
CHANNEL
Use when moving VCR to new location, or if a mistake
was made in the One Time VCR Setup section.
• Make sure a tape is not inserted in the VCR.
Turn VCR
Power on.
1
Do “One Time VCR Setup” steps on page 6.
3
VCR & Cassette Information
Break off the tab.
Prevent Accidental Tape Erasure
Record/Playback Time
Record Tab
Screw driver
Cover the hole
with cellophane tape.
To record again
Press and hold both PLAY
and CHANNEL on the VCR
for more than 5 seconds.
• The power will shut off.
2
Reset All VCR Memory Functions
DST (Daylight Saving Time)
SP
(Standard Play)
2 Hours
40 Minutes
1 Hour 2 Hours
5 Hours
20 Minutes
2 Hours 4 Hours
LP
(Long Play)
3 Hours 6 Hours 8 Hours
SLP
(Super Long Play)
Type of Video Cassette
Tape Speed
Setting T160
T120T60
Only use tapes with the mark in this unit.
VCR auto adjusts clock for DST
. (Page 7.)
Spring (First Sunday in April)
DST:ON --> sets clock ahead one hour.
Autumn (Last Sunday in October)
DST:ON --> Turns clock back one hour.
•If your area does not observe Daylight Saving
Time, select DST:OFF.
•Keep these time changes in mind when
programming the VCR for timer recordings.
NV-FJ4620PX P40-43.p65 00/02/29, 0:4040
41
Digital Auto Picture
Automatically controls the video output signal for
less noise depending on the tape condition.
Digital Auto Tracking
Continuously analyzes the signal and adjusts for
optimum picture quality.
Manual Tracking Control
(to reduce picture
noise)
Use during Playback and Slow Motion mode to reduce
picture noise. Press CH (TRACKING) / buttons on
the remote control or on the VCR until the picture clears
up. To return to Auto Tracking, press POWER off, then
on again a few seconds later.
V-Lock Control (to reduce picture jitter)
In Still mode, CH (TRACKING) / buttons operate as
a V-Lock control.
Power Source: 110/120/220 V
AC Auto, 50/60 Hz
Power Consumption: Power On
Approx. 23 watts
Power Off
Approx. 3.3 watts
Video Signal: EIA Standard NTSC color
Video Recording System: 4 rotary heads helical
scanning system
Audio Track: 1 track (Normal)
2 channel (Hi-Fi Audio Sound)
Tuner: For USA
TV Tuners: VHF input ch2~ch13
Cable channels “A”~“EEE”,
“A-5”~“A-1”, “5A”, 65~94,
100~125
UHF input ch14~ch69
For EUROPE
TV Tuners: VHF input ch2~ch13 (USA)
UHF input ch21~ch62 (C.C.I.R.)
Broadcast Channels: VHF 2~13, UHF 14~69
CABLE Channels: Midband A through I (14~22)
Superband J through W (23~36)
Hyperband AA~EEE (37~64)
Lowband A-5~A-1 (95~99)
Special CABLE channel 5 A
(01)
Ultraband 65~94, 100~125
Operating Temperature: 5 °C~40 °C (41 °F~104 °F)
Operating Humidity: 10 %~75 %
Weight: 3.4 kC (7.4 lbs.)
Dimensions: 430 (W) x 98 (H) x 250 (D) mm
16-15/16” (W) x 3-7/8” (H) x
9-3/4” (D)
Video Head Clog Sensor
During playback this
screen appears if
clogging is detected.
To remove screen,
press PLAY on the
remote or VCR.
• Use “dry” type head cleaning cassette only.
(Part No. NV-TCL30PT is recommended.)
Playing older or damaged tapes may eventually
cause video heads to become clogged.
Specifications
Head Cleaning
•Follow cleaning tape instructions carefully.
Excessive use of tape can shorten head life.
•If head clog symptoms persist, contact your
nearest Factory Service Center or authorized
Service Center. (See page 45.)
Use a soft cloth or dusting attachment of
your vacuum cleaner to dust your VCR.
Remove dust from the ventilation holes on
the back sides and bottom of the cabinet.
Plastic surfaces are easily scratched and
can be marred by alcohol and various
solvents. Avoid excessive use of oil-based
furniture polishes since the materials used
in the cabinet will accumulate more dust.
We recommend using a nonabrasive,
antistatic cleaner and polisher.
Cleaning the VCR
Note: Designs and specifications are subject to change
without notice.
VCR & Cassette Information
V
I
D
EO HEADS
M
AY
N
EED
CLE
A
N
I
NG
PLEASE
I
NSERT
HEAD
CLE
A
N
I
NG
CASSE
TT
E
OR
REFER
T
O
MANUAL
END
:
P
L
AY KEY
PLAY
STOP/EJECT
REC
REW FF
POWER VCR/TV
VIDEO IN 2 L-AUDIO IN 2-R
/
ACTION
CHANNEL
Cleaning Tape
Features for a Quality Picture
R
R
R
R
R
R
R
R
A clean video head helps produce a clear
picture.
So, we have equipped your VCR with a built-
in, non-chemical head cleaning system that
helps prevent clogging of the video heads.
Cleaning is performed each time you load or
unload a video cassette.
Built-in Head Cleaner
•This feature is preventative only, If your video
heads are seriously clogged, consider the use
of a chemical non-abrasive head cleaning kit or
take your VCR to a Service Center.
NV-FJ4620PX P40-43.p65 00/02/29, 0:4041
42
REC
1
2
:
0
0
A
M
0
:
25
ABC
-
0
:
1
2
:
3
4
SP
1212
/
2
7
/
1
9
9
9
M
ON
1212
:
0
0
P
M
-
1
:
0
0
P
M
CH
0
8 8
ABC
MOMO
V
I
E
MEMORMEMOR
I
AL
MOMO
V
I
E
S
T
ER
EO
SAP
M
ONO
VCR Status &
Clock Display
Function & Channel Display Blank Tape/ No Video
Signal Indication
To display or
remove the overlay.
On-Screen Displays (OSD)
Function Status
Rec Time Remaining
(OTR mode only,
see page 9.)
0
8
A
BC
Press DISPLAY.
Current Time
Tape Speed
(See page 40.)
When a function button is
pressed, e.g. PLAY, or you
change channels, a 4
second display appears
first in large and then small
characters.(Some Station
names may also appear if
Channel Caption is set.
See page 32, 33.)
Counter
Whenever a blank section of a tape comes up
in Play mode, or when the selected channel
has no broadcast signal with the Weak Signal
Display Feature (page 37) set to OFF, the TV
screen will turn solid blue.
Channel Caption
(See pages 32, 33.)
or Channel
Time Stamp Data
(See pages 34, 35.)
•This is not displayed
in Rec mode.
Broadcast Audio
Being Received
(See page 30.)
Warning and Instruction Displays These displays will alert you of a
missed operation or provide further
instructions.
OSD
If no active channels
are found for CHANNEL
MEMORY...
If you attempt to set or
review a Timer
Recording and the
Clock is not set...
After a Timer Program
has been set...
If you press REC on the
remote control or VCR,
and a cassette is inserted
with no record tab...
If you press PLAY, FF,
REW, or REC on the
remote control or VCR
without a cassette
inserted...
If you press POWER or
STOP during a Timer
Recording...
(visible in VCR mode only)
If head cleaning becomes
necessary while playing
back a tape...
If you press a function
button other than STOP/
EJECT or POWER while
the VCR is in VCR Lock
mode...
If you press any invalid
keys on the remote while
in CABLE/DSS mode...
Caution Pg Caution Pg
20
21
36
NO CH FOUND
PLEASE CHECK ANTENNA
CABLE CONNECTION THEN
PUSH VCR CH UP KEY AGAIN
PLEASE SET CLOCK
BEFORE PROGRAMMING
CHECK CASSETTE
RECORD TAB
NO CASSETTE
PLEASE INSERT A CASSETTE
OSD
40
8
9
13
12
612
If you press any invalid
keys on the remote while
in TV mode...
20
21
36
TURN VCR OFF
FOR TIMER RECORDING
TO CANCEL TIMER REC
PUSH POWER THEN STOP KEY
VIDEO HEADS MAY
NEED CLEANING
PLEASE INSERT HEAD
CLEANING CASSETTE
OR REFER TO MANUAL
END: PLAY KEY
VCR LOCK ACTIVATED
REMOTE CONTROL IS SET
TO CABLE/DSS MODE
USE VCR : VCR KEY
USE TV : TV KEY
REMOTE CONTROL IS SET
TO TV MODE
USE VCR : VCR KEY
USE CABLE/DSS : CABLE/DSS
41
36
NV-FJ4620PX P40-43.p65 00/02/29, 0:4042
43
Power
No power…
Recording & Playback
TV program cannot be recorded...
Timer recording cannot be performed…
There is no playback picture, or the playback
picture is noisy or contains streaks...
Special effects playback, picture may contain
some vertical jitter when using a TV with an
Automatic Vertical Hold Control...
VCR cannot be controlled...
Check the following points once again if you are having trouble with your VCR.
Correction
•Check connections between VCR, external antenna, and TV.
•Check hook up selection. (P.4~5)
•Make sure your antenna system (CABLE or TV) is correctly set.
(Channels [P.38])
•Make sure cassette record tab is intact. (P.40)
•Check clock is set to current time and date.
•Make sure Cable/DSS box (if used) is left on and tuned to
channel to be recorded.
•Set recording start/stop times correctly. (P.12)
•Make sure POWER button is set to off. (P.12, 13)
•Timer recording may not be performed or continued if a power
interruption of more than 1 minute occurs before or during, a
Timer Recording, even after power is restored.
•Select channel 3 or 4 on TV to match VCR output channel (3 or 4)
(P.6) or select LINE.
•Set VCR/TV selector to “VCR.”
•Adjust TRACKING control in either direction. (P.41)
•Try Head Cleaning. (P.41)
•Set TV’s Vertical Hold Control to MANUAL, then adjust.
•Make sure VCR LOCK is set to off. (P.36)
•Make sure remote is in proper mode. (P.20)
•Make sure unit is not in a Timer Record operation.
Correction
•Completely insert Power Plug into an AC outlet.
•Set POWER button to on.
•Make sure power source is active.
Correction
•Aim Remote Control directly at remote sensor on VCR. (P.50)
•Avoid any object blocking signal path.
•Check remote batteries. (P.4)
•Make sure VCR LOCK is set to off. (P.36)
•Exposing VCR remote sensor to direct fluorescent or outdoor
light may cause signal interference.
•Press VCR button for VCR mode. (P.20)
•Check remote Batteries. (P.4)
Correction
•Set VCR/TV selector to “TV.” (P.9)
•Make sure proper signal source is selected.
•Insert the cassette with window side up; record tab facing you.
•Insure no other tape is inside unit.
•Completely insert Power Plug into AC outlet.
•Make sure cassette record tab is intact. (P.40)
•To enable Quick play mechanism, the cylinder will rotate for
about 5 minutes. This reduces response time from Stop to Play
mode and from Play to Rewind Search mode.
•Because VCR playback signal is not as stable as off-the-air TV
signal, top of TV screen may be bent or unstable during
playback. Slowly turn TV horizontal Hold control to correct. If
your TV has no horizontal Hold control or adjusting control is
ineffective, contact your nearest TV service center.
Miscellaneous
Programs cannot be viewed on TV...
Video cassette cannot be inserted...
Video cassette cannot be removed...
Video cassette ejects when a recording is started
or the power is turned off for timer recording...
In Stop mode, the motor (CYLINDER) continues
to rotate...
The top of the playback picture waves back and
forth excessively...
Before Requesting Service
Remote Control
VCR cannot be remote controlled...
ACTION and PROG/VCR+ buttons cannot be
used...
OSD & Before Requesting Service
NV-FJ4620PX P40-43.p65 00/02/29, 0:4043